David S. Miller [Thu, 14 Apr 2016 01:49:03 +0000 (21:49 -0400)]
Merge git://git./pub/scm/linux/kernel/git/pablo/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree. More
specifically, they are:
1) Fix missing filter table per-netns registration in arptables, from
Florian Westphal.
2) Resolve out of bound access when parsing TCP options in
nf_conntrack_tcp, patch from Jozsef Kadlecsik.
3) Prefer NFPROTO_BRIDGE extensions over NFPROTO_UNSPEC in ebtables,
this resolves conflict between xt_limit and ebt_limit, from Phil Sutter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 13 Apr 2016 21:55:39 +0000 (17:55 -0400)]
Merge tag 'wireless-drivers-for-davem-2016-04-13' of git://git./linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.6
b43
* fix memory leaks when removing the device
bcma
* fix building without OF_IRQ
rtlwifi
* fix gcc-6 indentation warning
iwlwifi
* lower the debug level of a benign print
* fix a memory leak
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Sutter [Mon, 11 Apr 2016 23:31:14 +0000 (01:31 +0200)]
netfilter: ebtables: Fix extension lookup with identical name
If a requested extension exists as module and is not loaded,
ebt_check_match() might accidentally use an NFPROTO_UNSPEC one with same
name and fail.
Reproduced with limit match: Given xt_limit and ebt_limit both built as
module, the following would fail:
modprobe xt_limit
ebtables -I INPUT --limit 1/s -j ACCEPT
The fix is to make ebt_check_match() distrust a found NFPROTO_UNSPEC
extension and retry after requesting an appropriate module.
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
stephen hemminger [Mon, 11 Apr 2016 20:39:08 +0000 (13:39 -0700)]
devlink: add missing install of header
The new devlink.h in uapi was not being installed by
make headers_install
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 7 Apr 2016 18:10:41 +0000 (11:10 -0700)]
net: vrf: Fix dev refcnt leak due to IPv6 prefix route
ifupdown2 found a kernel bug with IPv6 routes and movement from the main
table to the VRF table. Sequence of events:
Create the interface and add addresses:
ip link add dev eth4.105 link eth4 type vlan id 105
ip addr add dev eth4.105 8.105.105.10/24
ip -6 addr add dev eth4.105 2008:105:105::10/64
At this point IPv6 has inserted a prefix route in the main table even
though the interface is 'down'. From there the VRF device is created:
ip link add dev vrf105 type vrf table 105
ip addr add dev vrf105 9.9.105.10/32
ip -6 addr add dev vrf105 2000:9:105::10/128
ip link set vrf105 up
Then the interface is enslaved, while still in the 'down' state:
ip link set dev eth4.105 master vrf105
Since the device is down the VRF driver cycling the device does not
send the NETDEV_UP and NETDEV_DOWN but rather the NETDEV_CHANGE event
which does not flush the routes inserted prior.
When the link is brought up
ip link set dev eth4.105 up
the prefix route is added in the VRF table, but does not remove
the route from the main table.
Fix by handling the NETDEV_CHANGEUPPER event similar what was implemented
for IPv4 in
7f49e7a38b77 ("net: Flush local routes when device changes vrf
association")
Fixes:
35402e3136634 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 7 Apr 2016 18:10:06 +0000 (11:10 -0700)]
net: vrf: Fix dst reference counting
Vivek reported a kernel exception deleting a VRF with an active
connection through it. The root cause is that the socket has a cached
reference to a dst that is destroyed. Converting the dst_destroy to
dst_release and letting proper reference counting kick in does not
work as the dst has a reference to the device which needs to be released
as well.
I talked to Hannes about this at netdev and he pointed out the ipv4 and
ipv6 dst handling has dst_ifdown for just this scenario. Rather than
continuing with the reinvented dst wheel in VRF just remove it and
leverage the ipv4 and ipv6 versions.
Fixes:
193125dbd8eb2 ("net: Introduce VRF device driver")
Fixes:
35402e3136634 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 11 Apr 2016 19:22:21 +0000 (15:22 -0400)]
Merge branch 'tipc-fixes'
Jon Maloy says:
====================
tipc: name distributor pernet queue
Commit #1 fixes a potential issue with deferred binding table
updates being pushed to the wrong namespace.
Commit #2 solves a problem with deferred binding table updates
remaining in the the defer queue after the issuing node has gone
down.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Hugne [Thu, 7 Apr 2016 14:40:44 +0000 (10:40 -0400)]
tipc: purge deferred updates from dead nodes
If a peer node becomes unavailable, in addition to removing the
nametable entries from this node we also need to purge all deferred
updates associated with this node.
Signed-off-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Hugne [Thu, 7 Apr 2016 14:40:43 +0000 (10:40 -0400)]
tipc: make dist queue pernet
Nametable updates received from the network that cannot be applied
immediately are placed on a defer queue. This queue is global to the
TIPC module, which might cause problems when using TIPC in containers.
To prevent nametable updates from escaping into the wrong namespace,
we make the queue pernet instead.
Signed-off-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Mon, 11 Apr 2016 05:37:58 +0000 (11:07 +0530)]
cxgb4: Stop Rx Queues before freeing it up
Stop all Ethernet RX Queues before freeing up various Ingress/Egress
Queues, etc. We were seeing cases of Ingress Queues not getting serviced
during the shutdown process leading to Ingress Paths jamming up through
the chip and blocking the shutdown effort itself.
One such case involved the Firmware sending a "Flush Token" through the
ULP-TX -> ULP-RX path for an Ethernet TX Queue being freed in order to
make sure there weren't any remaining TX Work Requests in the pipeline.
But the return path was stalled by Ingress Data unable to be delivered to
the Host because those Ingress Queues were no longer being serviced.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Reid [Thu, 7 Apr 2016 07:55:35 +0000 (15:55 +0800)]
net: stmmac: socfgpa: Ensure emac bit set in System Manger for PTP
When using the PTP fpga to hps clock source for the stmmac module
the appropriate bit in the System Manager FPGA Interface Group register
needs to be set. This is not set by the bootloader setup when the
HPS emac pins are being for this emac module.
This allows the PTP clock to be sourced from the FPGA and also connects
the PTP pps and ext trig signals to the stmmac PTP hardware.
Patch proposed by Phil Collins.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Ivanov [Thu, 7 Apr 2016 07:31:38 +0000 (09:31 +0200)]
netlink: don't send NETLINK_URELEASE for unbound sockets
All existing users of NETLINK_URELEASE use it to clean up resources that
were previously allocated to a socket via some command. As a result, no
users require getting this notification for unbound sockets.
Sending it for unbound sockets, however, is a problem because any user
(including unprivileged users) can create a socket that uses the same ID
as an existing socket. Binding this new socket will fail, but if the
NETLINK_URELEASE notification is generated for such sockets, the users
thereof will be tricked into thinking the socket that they allocated the
resources for is closed.
In the nl80211 case, this will cause destruction of virtual interfaces
that still belong to an existing hostapd process; this is the case that
Dmitry noticed. In the NFC case, it will cause a poll abort. In the case
of netlink log/queue it will cause them to stop reporting events, as if
NFULNL_CFG_CMD_UNBIND/NFQNL_CFG_CMD_UNBIND had been called.
Fix this problem by checking that the socket is bound before generating
the NETLINK_URELEASE notification.
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 11 Apr 2016 03:01:30 +0000 (23:01 -0400)]
decnet: Do not build routes to devices without decnet private data.
In particular, make sure we check for decnet private presence
for loopback devices.
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcelo Ricardo Leitner [Wed, 6 Apr 2016 18:15:19 +0000 (15:15 -0300)]
sctp: avoid refreshing heartbeat timer too often
Currently on high rate SCTP streams the heartbeat timer refresh can
consume quite a lot of resources as timer updates are costly and it
contains a random factor, which a) is also costly and b) invalidates
mod_timer() optimization for not editing a timer to the same value.
It may even cause the timer to be slightly advanced, for no good reason.
As suggested by David Laight this patch now removes this timer update
from hot path by leaving the timer on and re-evaluating upon its
expiration if the heartbeat is still needed or not, similarly to what is
done for TCP. If it's not needed anymore the timer is re-scheduled to
the new timeout, considering the time already elapsed.
For this, we now record the last tx timestamp per transport, updated in
the same spots as hb timer was restarted on tx. Also split up
sctp_transport_reset_timers into sctp_transport_reset_t3_rtx and
sctp_transport_reset_hb_timer, so we can re-arm T3 without re-arming the
heartbeat one.
On loopback with MTU of 65535 and data chunks with 1636, so that we
have a considerable amount of chunks without stressing system calls,
netperf -t SCTP_STREAM -l 30, perf looked like this before:
Samples: 103K of event 'cpu-clock', Event count (approx.):
25833000000
Overhead Command Shared Object Symbol
+ 6,15% netperf [kernel.vmlinux] [k] copy_user_enhanced_fast_string
- 5,43% netperf [kernel.vmlinux] [k] _raw_write_unlock_irqrestore
- _raw_write_unlock_irqrestore
- 96,54% _raw_spin_unlock_irqrestore
- 36,14% mod_timer
+ 97,24% sctp_transport_reset_timers
+ 2,76% sctp_do_sm
+ 33,65% __wake_up_sync_key
+ 28,77% sctp_ulpq_tail_event
+ 1,40% del_timer
- 1,84% mod_timer
+ 99,03% sctp_transport_reset_timers
+ 0,97% sctp_do_sm
+ 1,50% sctp_ulpq_tail_event
And after this patch, now with netperf -l 60:
Samples: 230K of event 'cpu-clock', Event count (approx.):
57707250000
Overhead Command Shared Object Symbol
+ 5,65% netperf [kernel.vmlinux] [k] memcpy_erms
+ 5,59% netperf [kernel.vmlinux] [k] copy_user_enhanced_fast_string
- 5,05% netperf [kernel.vmlinux] [k] _raw_spin_unlock_irqrestore
- _raw_spin_unlock_irqrestore
+ 49,89% __wake_up_sync_key
+ 45,68% sctp_ulpq_tail_event
- 2,85% mod_timer
+ 76,51% sctp_transport_reset_t3_rtx
+ 23,49% sctp_do_sm
+ 1,55% del_timer
+ 2,50% netperf [sctp] [k] sctp_datamsg_from_user
+ 2,26% netperf [sctp] [k] sctp_sendmsg
Throughput-wise, from 6800mbps without the patch to 7050mbps with it,
~3.7%.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sat, 9 Apr 2016 23:28:41 +0000 (02:28 +0300)]
sh_eth: re-enable-E-MAC interrupts in sh_eth_set_ringparam()
The E-MAC interrupts are left disabled when the ring parameters are changed
via 'ethtool'. In order to fix this, it's enough to call sh_eth_dev_init()
with 'true' instead of 'false' for the second argument (which conveniently
allows us to remove the following code re-enabling E-DMAC interrupts and
reception).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 9 Apr 2016 19:32:44 +0000 (12:32 -0700)]
Merge tag 'tty-4.6-rc3' of git://git./linux/kernel/git/gregkh/tty
Pull tty fixes from Greg KH:
"Here are two tty fixes for issues found.
One was due to a merge error in 4.6-rc1, and the other a regression
fix for UML consoles that broke in 4.6-rc1.
Both have been in linux-next for a while"
* tag 'tty-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix merge of "tty: Refactor tty_open()"
tty: Fix UML console breakage
Linus Torvalds [Sat, 9 Apr 2016 19:23:02 +0000 (12:23 -0700)]
Merge tag 'usb-4.6-rc3' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes and new device ids for 4.6-rc3.
Nothing major, the normal USB gadget fixes and usb-serial driver ids,
along with some other fixes mixed in. All except the USB serial ids
have been tested in linux-next, the id additions should be fine as
they are 'trivial'"
* tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
USB: option: add "D-Link DWM-221 B1" device id
USB: serial: cp210x: Adding GE Healthcare Device ID
USB: serial: ftdi_sio: Add support for ICP DAS I-756xU devices
usb: dwc3: keystone: drop dma_mask configuration
usb: gadget: udc-core: remove manual dma configuration
usb: dwc3: pci: add ID for one more Intel Broxton platform
usb: renesas_usbhs: fix to avoid using a disabled ep in usbhsg_queue_done()
usb: dwc2: do not override forced dr_mode in gadget setup
usb: gadget: f_midi: unlock on error
USB: digi_acceleport: do sanity checking for the number of ports
USB: cypress_m8: add endpoint sanity check
USB: mct_u232: add sanity checking in probe
usb: fix regression in SuperSpeed endpoint descriptor parsing
USB: usbip: fix potential out-of-bounds write
usb: renesas_usbhs: disable TX IRQ before starting TX DMAC transfer
usb: renesas_usbhs: avoid NULL pointer derefernce in usbhsf_pkt_handler()
usb: gadget: f_midi: Fixed a bug when buflen was smaller than wMaxPacketSize
usb: phy: qcom-8x16: fix regulator API abuse
usb: ch9: Fix SSP Device Cap wFunctionalitySupport type
usb: gadget: composite: Access SSP Dev Cap fields properly
...
Linus Torvalds [Sat, 9 Apr 2016 19:09:37 +0000 (12:09 -0700)]
Merge tag 'staging-4.6-rc3' of git://git./linux/kernel/git/gregkh/staging
Pull staging and IIO driver fixes from Greg KH:
"Here are some IIO driver fixes, along with two staging driver fixes
for 4.6-rc3.
One staging driver patch reverts the deletion of a driver that
happened in 4.6-rc1. We thought that laptop.org was dead, but it's
still alive and kicking, and has users that were mad we broke their
hardware by deleting a driver for their machines. So that driver is
added back and everyone is happy again.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Revert "Staging: olpc_dcon: Remove obsolete driver"
staging/rdma/hfi1: select CRC32
iio: gyro: bmg160: fix buffer read values
iio: gyro: bmg160: fix endianness when reading axes
iio: accel: bmc150: fix endianness when reading axes
iio: st_magn: always define ST_MAGN_TRIGGER_SET_STATE
iio: fix config watermark initial value
iio: health: max30100: correct FIFO check condition
iio: imu: Fix inv_mpu6050 dependencies
iio: adc: Fix build error of missing devm_ioremap_resource on UM
iio: light: apds9960: correct FIFO check condition
iio: adc: max1363: correct reference voltage
iio: adc: max1363: add missing adc to max1363_id
Linus Torvalds [Sat, 9 Apr 2016 19:00:42 +0000 (12:00 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of eight fixes.
Two are trivial gcc-6 updates (brace additions and unused variable
removal). There's a couple of cxlflash regressions, a correction for
sd being overly chatty on revalidation (causing excess log increases).
A VPD issue which could crash USB devices because they seem very
intolerant to VPD inquiries, an ALUA deadlock fix and a mpt3sas buffer
overrun fix"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: Do not attach VPD to devices that don't support it
sd: Fix excessive capacity printing on devices with blocks bigger than 512 bytes
scsi_dh_alua: Fix a recently introduced deadlock
scsi: Declare local symbols static
cxlflash: Move to exponential back-off when cmd_room is not available
cxlflash: Fix regression issue with re-ordering patch
mpt3sas: Don't overreach ioc->reply_post[] during initialization
aacraid: add missing curly braces
Linus Torvalds [Sat, 9 Apr 2016 18:23:27 +0000 (11:23 -0700)]
Merge tag 'md/4.6-rc2-fix' of git://git./linux/kernel/git/shli/md
Pull MD fixes from Shaohua Li:
"This update mainly fixes bugs:
- fix error handling (Guoqing)
- fix a crash when a disk is hotremoved (me)
- fix a dead loop (Wei Fang)"
* tag 'md/4.6-rc2-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md/bitmap: clear bitmap if bitmap_create failed
MD: add rdev reference for super write
md: fix a trivial typo in comments
md:raid1: fix a dead loop when read from a WriteMostly disk
Linus Torvalds [Sat, 9 Apr 2016 18:03:48 +0000 (11:03 -0700)]
Merge tag 'pm+acpi-4.6-rc3' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"Fixes for some issues discovered after recent changes and for some
that have just been found lately regardless of those changes
(intel_pstate, intel_idle, PM core, mailbox/pcc, turbostat) plus
support for some new CPU models (intel_idle, Intel RAPL driver,
turbostat) and documentation updates (intel_pstate, PM core).
Specifics:
- intel_pstate fixes for two issues exposed by the recent switch over
from using timers and for one issue introduced during the 4.4 cycle
plus new comments describing data structures used by the driver
(Rafael Wysocki, Srinivas Pandruvada).
- intel_idle fixes related to CPU offline/online (Richard Cochran).
- intel_idle support (new CPU IDs and state definitions mostly) for
Skylake-X and Kabylake processors (Len Brown).
- PCC mailbox driver fix for an out-of-bounds memory access that may
cause the kernel to panic() (Shanker Donthineni).
- New (missing) CPU ID for one apparently overlooked Haswell model in
the Intel RAPL power capping driver (Srinivas Pandruvada).
- Fix for the PM core's wakeup IRQs framework to make it work after
wakeup settings reconfiguration from sysfs (Grygorii Strashko).
- Runtime PM documentation update to make it describe what needs to
be done during device removal more precisely (Krzysztof Kozlowski).
- Stale comment removal cleanup in the cpufreq-dt driver (Viresh
Kumar).
- turbostat utility fixes and support for Broxton, Skylake-X and
Kabylake processors (Len Brown)"
* tag 'pm+acpi-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
PM / wakeirq: fix wakeirq setting after wakup re-configuration from sysfs
tools/power turbostat: work around RC6 counter wrap
tools/power turbostat: initial KBL support
tools/power turbostat: initial SKX support
tools/power turbostat: decode BXT TSC frequency via CPUID
tools/power turbostat: initial BXT support
tools/power turbostat: print IRTL MSRs
tools/power turbostat: SGX state should print only if --debug
intel_idle: Add KBL support
intel_idle: Add SKX support
intel_idle: Clean up all registered devices on exit.
intel_idle: Propagate hot plug errors.
intel_idle: Don't overreact to a cpuidle registration failure.
intel_idle: Setup the timer broadcast only on successful driver load.
intel_idle: Avoid a double free of the per-CPU data.
intel_idle: Fix dangling registration on error path.
intel_idle: Fix deallocation order on the driver exit path.
intel_idle: Remove redundant initialization calls.
intel_idle: Fix a helper function's return value.
intel_idle: remove useless return from void function.
...
Linus Torvalds [Sat, 9 Apr 2016 17:50:44 +0000 (10:50 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Stale SKB data pointer access across pskb_may_pull() calls in L2TP,
from Haishuang Yan.
2) Fix multicast frame handling in mac80211 AP code, from Felix
Fietkau.
3) mac80211 station hashtable insert errors not handled properly, fix
from Johannes Berg.
4) Fix TX descriptor count limit handling in e1000, from Alexander
Duyck.
5) Revert a buggy netdev refcount fix in netpoll, from Bjorn Helgaas.
6) Must assign rtnl_link_ops of the device before registering it, fix
in ip6_tunnel from Thadeu Lima de Souza Cascardo.
7) Memory leak fix in tc action net exit, from WANG Cong.
8) Add missing AF_KCM entries to name tables, from Dexuan Cui.
9) Fix regression in GRE handling of csums wrt. FOU, from Alexander
Duyck.
10) Fix memory allocation alignment and congestion map corruption in
RDS, from Shamir Rabinovitch.
11) Fix default qdisc regression in tuntap driver, from Jason Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
bridge, netem: mark mailing lists as moderated
tuntap: restore default qdisc
mpls: find_outdev: check for err ptr in addition to NULL check
ipv6: Count in extension headers in skb->network_header
RDS: fix congestion map corruption for PAGE_SIZE > 4k
RDS: memory allocated must be align to 8
GRE: Disable segmentation offloads w/ CSUM and we are encapsulated via FOU
net: add the AF_KCM entries to family name tables
MAINTAINERS: intel-wired-lan list is moderated
lib/test_bpf: Add additional BPF_ADD tests
lib/test_bpf: Add test to check for result of 32-bit add that overflows
lib/test_bpf: Add tests for unsigned BPF_JGT
lib/test_bpf: Fix JMP_JSET tests
VSOCK: Detach QP check should filter out non matching QPs.
stmmac: fix adjust link call in case of a switch is attached
af_packet: tone down the Tx-ring unsupported spew.
net_sched: fix a memory leak in tc action
samples/bpf: Enable powerpc support
samples/bpf: Use llc in PATH, rather than a hardcoded value
samples/bpf: Fix build breakage with map_perf_test_user.c
...
Linus Torvalds [Sat, 9 Apr 2016 17:41:34 +0000 (10:41 -0700)]
Merge branch 'for-linus-4.6' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"These are bug fixes, including a really old fsync bug, and a few trace
points to help us track down problems in the quota code"
* 'for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix file/data loss caused by fsync after rename and new inode
btrfs: Reset IO error counters before start of device replacing
btrfs: Add qgroup tracing
Btrfs: don't use src fd for printk
btrfs: fallback to vmalloc in btrfs_compare_tree
btrfs: handle non-fatal errors in btrfs_qgroup_inherit()
btrfs: Output more info for enospc_debug mount option
Btrfs: fix invalid reference in replace_path
Btrfs: Improve FL_KEEP_SIZE handling in fallocate
Linus Torvalds [Sat, 9 Apr 2016 17:33:58 +0000 (10:33 -0700)]
Merge tag 'for-linus-4.6-ofs1' of git://git./linux/kernel/git/hubcap/linux
Pull orangefs fixes from Mike Marshall:
"Orangefs cleanups and a strncpy vulnerability fix.
Cleanups:
- remove an unused variable from orangefs_readdir.
- clean up printk wrapper used for ofs "gossip" debugging.
- clean up truncate ctime and mtime setting in inode.c
- remove a useless null check found by coccinelle.
- optimize some memcpy/memset boilerplate code.
- remove some useless sanity checks from xattr.c
Fix:
- fix a potential strncpy vulnerability"
* tag 'for-linus-4.6-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
orangefs: remove unused variable
orangefs: Add KERN_<LEVEL> to gossip_<level> macros
orangefs: strncpy -> strscpy
orangefs: clean up truncate ctime and mtime setting
Orangefs: fix ifnullfree.cocci warnings
Orangefs: optimize boilerplate code.
Orangefs: xattr.c cleanup
Linus Torvalds [Sat, 9 Apr 2016 17:23:45 +0000 (10:23 -0700)]
Merge tag 'iommu-fixes-v4.6-rc2' of git://git./linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- compile-time fixes (warnings and failures)
- a bug in iommu core code which could cause the group->domain pointer
to be falsly cleared
- fix in scatterlist handling of the ARM common DMA-API code
- stall detection fix for the Rockchip IOMMU driver
* tag 'iommu-fixes-v4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Silence an uninitialized variable warning
iommu/rockchip: Fix "is stall active" check
iommu: Don't overwrite domain pointer when there is no default_domain
iommu/dma: Restore scatterlist offsets correctly
iommu: provide of_xlate pointer unconditionally
Greg Kroah-Hartman [Fri, 8 Apr 2016 22:41:58 +0000 (15:41 -0700)]
Merge tag 'usb-serial-4.6-rc3' of git://git./linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.6-rc3
Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
David S. Miller [Fri, 8 Apr 2016 20:41:28 +0000 (16:41 -0400)]
Merge tag 'mac80211-for-davem-2016-04-06' of git://git./linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
For the current RC series, we have the following fixes:
* TDLS fixes from Arik and Ilan
* rhashtable fixes from Ben and myself
* documentation fixes from Luis
* U-APSD fixes from Emmanuel
* a TXQ fix from Felix
* and a compiler warning suppression from Jeff
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Tue, 5 Apr 2016 20:43:53 +0000 (13:43 -0700)]
bridge, netem: mark mailing lists as moderated
I moderate these (lightly loaded) lists to block spam.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Fri, 8 Apr 2016 05:26:48 +0000 (13:26 +0800)]
tuntap: restore default qdisc
After commit
f84bb1eac027 ("net: fix IFF_NO_QUEUE for drivers using
alloc_netdev"), default qdisc was changed to noqueue because
tuntap does not set tx_queue_len during .setup(). This patch restores
default qdisc by setting tx_queue_len in tun_setup().
Fixes:
f84bb1eac027 ("net: fix IFF_NO_QUEUE for drivers using alloc_netdev")
Cc: Phil Sutter <phil@nwl.cc>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Brandenburg [Mon, 4 Apr 2016 20:26:38 +0000 (16:26 -0400)]
orangefs: remove unused variable
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Rafael J. Wysocki [Fri, 8 Apr 2016 19:46:56 +0000 (21:46 +0200)]
Merge branches 'pm-core', 'powercap' and 'pm-tools'
* pm-core:
PM / wakeirq: fix wakeirq setting after wakup re-configuration from sysfs
PM / runtime: Document steps for device removal
* powercap:
powercap: intel_rapl: Add missing Haswell model
* pm-tools:
tools/power turbostat: work around RC6 counter wrap
tools/power turbostat: initial KBL support
tools/power turbostat: initial SKX support
tools/power turbostat: decode BXT TSC frequency via CPUID
tools/power turbostat: initial BXT support
tools/power turbostat: print IRTL MSRs
tools/power turbostat: SGX state should print only if --debug
Rafael J. Wysocki [Fri, 8 Apr 2016 19:46:05 +0000 (21:46 +0200)]
Merge branches 'pm-cpufreq', 'pm-cpuidle' and 'acpi-cppc'
* pm-cpufreq:
cpufreq: dt: Drop stale comment
cpufreq: intel_pstate: Documenation for structures
cpufreq: intel_pstate: fix inconsistency in setting policy limits
intel_pstate: Avoid extra invocation of intel_pstate_sample()
intel_pstate: Do not set utilization update hook too early
* pm-cpuidle:
intel_idle: Add KBL support
intel_idle: Add SKX support
intel_idle: Clean up all registered devices on exit.
intel_idle: Propagate hot plug errors.
intel_idle: Don't overreact to a cpuidle registration failure.
intel_idle: Setup the timer broadcast only on successful driver load.
intel_idle: Avoid a double free of the per-CPU data.
intel_idle: Fix dangling registration on error path.
intel_idle: Fix deallocation order on the driver exit path.
intel_idle: Remove redundant initialization calls.
intel_idle: Fix a helper function's return value.
intel_idle: remove useless return from void function.
* acpi-cppc:
mailbox: pcc: Don't access an unmapped memory address space
Joe Perches [Sun, 27 Mar 2016 21:34:52 +0000 (14:34 -0700)]
orangefs: Add KERN_<LEVEL> to gossip_<level> macros
Emit the logging messages at the appropriate levels.
Miscellanea:
o Change format to fmt
o Use the more common ##__VA_ARGS__
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Martin Brandenburg [Fri, 8 Apr 2016 17:33:21 +0000 (13:33 -0400)]
orangefs: strncpy -> strscpy
It would have been possible for a rogue client-core to send in a symlink
target which is not NUL terminated. This returns EIO if the client-core
gives us corrupt data.
Leave debugfs and superblock code as is for now.
Other dcache.c and namei.c strncpy instances are safe because
ORANGEFS_NAME_MAX = NAME_MAX + 1; there is always enough space for a
name plus a NUL byte.
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Martin Brandenburg [Mon, 4 Apr 2016 20:26:36 +0000 (16:26 -0400)]
orangefs: clean up truncate ctime and mtime setting
The ctime and mtime are always updated on a successful ftruncate and
only updated on a successful truncate where the size changed.
We handle the ``if the size changed'' bit.
This matches FUSE's behavior.
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
kbuild test robot [Sat, 26 Mar 2016 18:54:23 +0000 (02:54 +0800)]
Orangefs: fix ifnullfree.cocci warnings
fs/orangefs/orangefs-debugfs.c:130:2-26: WARNING: NULL check before freeing functions like kfree, debugfs_remove, debugfs_remove_recursive or usb_free_urb is not needed. Maybe consider reorganizing relevant code to avoid passing NULL values.
NULL check before some freeing functions is not needed.
Based on checkpatch warning
"kfree(NULL) is safe this check is probably not required"
and kfreeaddr.cocci by Julia Lawall.
Generated by: scripts/coccinelle/free/ifnullfree.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Mike Marshall [Wed, 6 Apr 2016 15:19:37 +0000 (11:19 -0400)]
Orangefs: optimize boilerplate code.
Suggested by David Binderman <dcb314@hotmail.com>
The former can potentially be a performance win over the latter.
memcpy(d, s, len);
memset(d+len, c, size-len);
memset(d, c, size);
memcpy(d, s, len);
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Mike Marshall [Wed, 6 Apr 2016 14:52:38 +0000 (10:52 -0400)]
Orangefs: xattr.c cleanup
1. It is nonsense to test for negative size_t, suggested by
David Binderman <dcb314@hotmail.com>
2. By the time Orangefs gets called, the vfs has ensured that
name != NULL, and that buffer and size are sane.
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Roopa Prabhu [Fri, 8 Apr 2016 04:28:38 +0000 (21:28 -0700)]
mpls: find_outdev: check for err ptr in addition to NULL check
find_outdev calls inet{,6}_fib_lookup_dev() or dev_get_by_index() to
find the output device. In case of an error, inet{,6}_fib_lookup_dev()
returns error pointer and dev_get_by_index() returns NULL. But the function
only checks for NULL and thus can end up calling dev_put on an ERR_PTR.
This patch adds an additional check for err ptr after the NULL check.
Before: Trying to add an mpls route with no oif from user, no available
path to 10.1.1.8 and no default route:
$ip -f mpls route add 100 as 200 via inet 10.1.1.8
[ 822.337195] BUG: unable to handle kernel NULL pointer dereference at
00000000000003a3
[ 822.340033] IP: [<
ffffffff8148781e>] mpls_nh_assign_dev+0x10b/0x182
[ 822.340033] PGD
1db38067 PUD
1de9e067 PMD 0
[ 822.340033] Oops: 0000 [#1] SMP
[ 822.340033] Modules linked in:
[ 822.340033] CPU: 0 PID: 11148 Comm: ip Not tainted 4.5.0-rc7+ #54
[ 822.340033] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS
rel-1.7.5.1-0-g8936dbb-20141113_115728-nilsson.home.kraxel.org
04/01/2014
[ 822.340033] task:
ffff88001db82580 ti:
ffff88001dad4000 task.ti:
ffff88001dad4000
[ 822.340033] RIP: 0010:[<
ffffffff8148781e>] [<
ffffffff8148781e>]
mpls_nh_assign_dev+0x10b/0x182
[ 822.340033] RSP: 0018:
ffff88001dad7a88 EFLAGS:
00010282
[ 822.340033] RAX:
ffffffffffffff9b RBX:
ffffffffffffff9b RCX:
0000000000000002
[ 822.340033] RDX:
00000000ffffff9b RSI:
0000000000000008 RDI:
0000000000000000
[ 822.340033] RBP:
ffff88001ddc9ea0 R08:
ffff88001e9f1768 R09:
0000000000000000
[ 822.340033] R10:
ffff88001d9c1100 R11:
ffff88001e3c89f0 R12:
ffffffff8187e0c0
[ 822.340033] R13:
ffffffff8187e0c0 R14:
ffff88001ddc9e80 R15:
0000000000000004
[ 822.340033] FS:
00007ff9ed798700(0000) GS:
ffff88001fc00000(0000)
knlGS:
0000000000000000
[ 822.340033] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 822.340033] CR2:
00000000000003a3 CR3:
000000001de89000 CR4:
00000000000006f0
[ 822.340033] Stack:
[ 822.340033]
0000000000000000 0000000100000000 0000000000000000
0000000000000000
[ 822.340033]
0000000000000000 0801010a00000000 0000000000000000
0000000000000000
[ 822.340033]
0000000000000004 ffffffff8148749b ffffffff8187e0c0
000000000000001c
[ 822.340033] Call Trace:
[ 822.340033] [<
ffffffff8148749b>] ? mpls_rt_alloc+0x2b/0x3e
[ 822.340033] [<
ffffffff81488e66>] ? mpls_rtm_newroute+0x358/0x3e2
[ 822.340033] [<
ffffffff810e7bbc>] ? get_page+0x5/0xa
[ 822.340033] [<
ffffffff813b7d94>] ? rtnetlink_rcv_msg+0x17e/0x191
[ 822.340033] [<
ffffffff8111794e>] ? __kmalloc_track_caller+0x8c/0x9e
[ 822.340033] [<
ffffffff813c9393>] ?
rht_key_hashfn.isra.20.constprop.57+0x14/0x1f
[ 822.340033] [<
ffffffff813b7c16>] ? __rtnl_unlock+0xc/0xc
[ 822.340033] [<
ffffffff813cb794>] ? netlink_rcv_skb+0x36/0x82
[ 822.340033] [<
ffffffff813b4507>] ? rtnetlink_rcv+0x1f/0x28
[ 822.340033] [<
ffffffff813cb2b1>] ? netlink_unicast+0x106/0x189
[ 822.340033] [<
ffffffff813cb5b3>] ? netlink_sendmsg+0x27f/0x2c8
[ 822.340033] [<
ffffffff81392ede>] ? sock_sendmsg_nosec+0x10/0x1b
[ 822.340033] [<
ffffffff81393df1>] ? ___sys_sendmsg+0x182/0x1e3
[ 822.340033] [<
ffffffff810e4f35>] ?
__alloc_pages_nodemask+0x11c/0x1e4
[ 822.340033] [<
ffffffff8110619c>] ? PageAnon+0x5/0xd
[ 822.340033] [<
ffffffff811062fe>] ? __page_set_anon_rmap+0x45/0x52
[ 822.340033] [<
ffffffff810e7bbc>] ? get_page+0x5/0xa
[ 822.340033] [<
ffffffff810e85ab>] ? __lru_cache_add+0x1a/0x3a
[ 822.340033] [<
ffffffff81087ea9>] ? current_kernel_time64+0x9/0x30
[ 822.340033] [<
ffffffff813940c4>] ? __sys_sendmsg+0x3c/0x5a
[ 822.340033] [<
ffffffff8148f597>] ?
entry_SYSCALL_64_fastpath+0x12/0x6a
[ 822.340033] Code: 83 08 04 00 00 65 ff 00 48 8b 3c 24 e8 40 7c f2 ff
eb 13 48 c7 c3 9f ff ff ff eb 0f 89 ce e8 f1 ae f1 ff 48 89 c3 48 85 db
74 15 <48> 8b 83 08 04 00 00 65 ff 08 48 81 fb 00 f0 ff ff 76 0d eb 07
[ 822.340033] RIP [<
ffffffff8148781e>] mpls_nh_assign_dev+0x10b/0x182
[ 822.340033] RSP <
ffff88001dad7a88>
[ 822.340033] CR2:
00000000000003a3
[ 822.435363] ---[ end trace
98cc65e6f6b8bf11 ]---
After patch:
$ip -f mpls route add 100 as 200 via inet 10.1.1.8
RTNETLINK answers: Network is unreachable
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Sitnicki [Tue, 5 Apr 2016 16:41:08 +0000 (18:41 +0200)]
ipv6: Count in extension headers in skb->network_header
When sending a UDPv6 message longer than MTU, account for the length
of fragmentable IPv6 extension headers in skb->network_header offset.
Same as we do in alloc_new_skb path in __ip6_append_data().
This ensures that later on __ip6_make_skb() will make space in
headroom for fragmentable extension headers:
/* move skb->data to ip header from ext header */
if (skb->data < skb_network_header(skb))
__skb_pull(skb, skb_network_offset(skb));
Prevents a splat due to skb_under_panic:
skbuff: skb_under_panic: text:
ffffffff8143397b len:2126 put:14 \
head:
ffff880005bacf50 data:
ffff880005bacf4a tail:0x48 end:0xc0 dev:lo
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:104!
invalid opcode: 0000 [#1] KASAN
CPU: 0 PID: 160 Comm: reproducer Not tainted 4.6.0-rc2 #65
[...]
Call Trace:
[<
ffffffff813eb7b9>] skb_push+0x79/0x80
[<
ffffffff8143397b>] eth_header+0x2b/0x100
[<
ffffffff8141e0d0>] neigh_resolve_output+0x210/0x310
[<
ffffffff814eab77>] ip6_finish_output2+0x4a7/0x7c0
[<
ffffffff814efe3a>] ip6_output+0x16a/0x280
[<
ffffffff815440c1>] ip6_local_out+0xb1/0xf0
[<
ffffffff814f1115>] ip6_send_skb+0x45/0xd0
[<
ffffffff81518836>] udp_v6_send_skb+0x246/0x5d0
[<
ffffffff8151985e>] udpv6_sendmsg+0xa6e/0x1090
[...]
Reported-by: Ji Jianwen <jiji@redhat.com>
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bart Van Assche [Thu, 7 Apr 2016 22:55:04 +0000 (15:55 -0700)]
Revert "ib_srpt: Convert to percpu_ida tag allocation"
This reverts commit
0fd10721fe3664f7549e74af9d28a509c9a68719.
That patch causes the ib_srpt driver to crash as soon as the first SCSI
command is received:
kernel BUG at drivers/infiniband/ulp/srpt/ib_srpt.c:1439!
invalid opcode: 0000 [#1] SMP
Workqueue: target_completion target_complete_ok_work [target_core_mod]
RIP: srpt_queue_response+0x437/0x4a0 [ib_srpt]
Call Trace:
srpt_queue_data_in+0x9/0x10 [ib_srpt]
target_complete_ok_work+0x152/0x2b0 [target_core_mod]
process_one_work+0x197/0x480
worker_thread+0x49/0x490
kthread+0xea/0x100
ret_from_fork+0x22/0x40
Aside from the crash, the shortcomings of that patch are as follows:
- It makes the ib_srpt driver use I/O contexts allocated by
transport_alloc_session_tags() but it does not initialize these I/O
contexts properly. All the initializations performed by
srpt_alloc_ioctx() are skipped.
- It swaps the order of the send ioctx allocation and the transition to
RTR mode which is wrong.
- The amount of memory that is needed for I/O contexts is doubled.
- srpt_rdma_ch.free_list is no longer used but is not removed.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 8 Apr 2016 00:22:20 +0000 (17:22 -0700)]
Merge tag 'ext4_for_linus_stable' of git://git./linux/kernel/git/tytso/ext4
Pull ext4 bugfixes from Ted Ts'o:
"These changes contains a fix for overlayfs interacting with some
(badly behaved) dentry code in various file systems. These have been
reviewed by Al and the respective file system mtinainers and are going
through the ext4 tree for convenience.
This also has a few ext4 encryption bug fixes that were discovered in
Android testing (yes, we will need to get these sync'ed up with the
fs/crypto code; I'll take care of that). It also has some bug fixes
and a change to ignore the legacy quota options to allow for xfstests
regression testing of ext4's internal quota feature and to be more
consistent with how xfs handles this case"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: ignore quota mount options if the quota feature is enabled
ext4 crypto: fix some error handling
ext4: avoid calling dquot_get_next_id() if quota is not enabled
ext4: retry block allocation for failed DIO and DAX writes
ext4: add lockdep annotations for i_data_sem
ext4: allow readdir()'s of large empty directories to be interrupted
btrfs: fix crash/invalid memory access on fsync when using overlayfs
ext4 crypto: use dget_parent() in ext4_d_revalidate()
ext4: use file_dentry()
ext4: use dget_parent() in ext4_file_open()
nfs: use file_dentry()
fs: add file_dentry()
ext4 crypto: don't let data integrity writebacks fail with ENOMEM
ext4: check if in-inode xattr is corrupted in ext4_expand_extra_isize_ea()
Linus Torvalds [Thu, 7 Apr 2016 23:34:26 +0000 (16:34 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sage/ceph-client
Pull Ceph fix from Sage Weil:
"This just fixes a few remaining memory allocations in RBD to use
GFP_NOIO instead of GFP_ATOMIC"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: use GFP_NOIO consistently for request allocations
Linus Torvalds [Thu, 7 Apr 2016 23:20:40 +0000 (16:20 -0700)]
Merge tag 'for_linus' of git://git./linux/kernel/git/mst/vhost
Pull virtio/qemu fixes from Michael S Tsirkin:
"A couple of fixes for virtio and for the new QEMU fw cfg driver"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio: add VIRTIO_CONFIG_S_NEEDS_RESET device status bit
MAINTAINERS: add entry for QEMU
firmware: qemu_fw_cfg.c: hold ACPI global lock during device access
virtio: virtio 1.0 cs04 spec compliance for reset
qemu_fw_cfg: don't leak kobj on init error
Linus Torvalds [Thu, 7 Apr 2016 22:53:19 +0000 (15:53 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"This is mostly amdgpu/radeon fixes, and imx related fixes.
There is also one one TTM fix, one nouveau fix, and one hdlcd fix.
The AMD ones are some fixes for power management after suspend/resume
one some GPUs, and some vblank fixes.
The IMX ones are for more stricter plane checks and some cleanups.
I'm off until Monday, so therre might be some fixes early next week if
anyone missed me"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (34 commits)
drm/nouveau/tegra: acquire and enable reference clock if needed
drm/amdgpu: total vram size also reduces pin size
drm/amd/powerplay: add uvd/vce dpm enabling flag default.
drm/amd/powerplay: fix issue that resume back, dpm can't work on FIJI.
drm/amdgpu: save and restore the firwmware cache part when suspend resume
drm/amdgpu: save and restore UVD context with suspend and resume
drm/ttm: use phys_addr_t for ttm_bus_placement
drm: ARM HDLCD - fix an error code
drm: ARM HDLCD - get rid of devm_clk_put()
drm/radeon: Only call drm_vblank_on/off between drm_vblank_init/cleanup
drm/amdgpu: fence wait old rcu slot
drm/amdgpu: fix leaking fence in the pageflip code
drm/amdgpu: print vram type rather than just DDR
drm/amdgpu/gmc: use proper register for vram type on Fiji
drm/amdgpu/gmc: move vram type fetching into sw_init
drm/amdgpu: Set vblank_disable_allowed = true
drm/radeon: Set vblank_disable_allowed = true
drm/amd/powerplay: Need to change boot to performance state in resume.
drm/amd/powerplay: add new Fiji function for not setting same ps.
drm/amdgpu: check dpm state before pm system fs initialized.
...
shamir rabinovitch [Thu, 7 Apr 2016 11:57:36 +0000 (07:57 -0400)]
RDS: fix congestion map corruption for PAGE_SIZE > 4k
When PAGE_SIZE > 4k single page can contain 2 RDS fragments. If
'rds_ib_cong_recv' ignore the RDS fragment offset in to the page it
then read the data fragment as far congestion map update and lead to
corruption of the RDS connection far congestion map.
Signed-off-by: Shamir Rabinovitch <shamir.rabinovitch@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
shamir rabinovitch [Thu, 7 Apr 2016 11:57:35 +0000 (07:57 -0400)]
RDS: memory allocated must be align to 8
Fix issue in 'rds_ib_cong_recv' when accessing unaligned memory
allocated by 'rds_page_remainder_alloc' using uint64_t pointer.
Signed-off-by: Shamir Rabinovitch <shamir.rabinovitch@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Tue, 5 Apr 2016 16:13:39 +0000 (09:13 -0700)]
GRE: Disable segmentation offloads w/ CSUM and we are encapsulated via FOU
This patch fixes an issue I found in which we were dropping frames if we
had enabled checksums on GRE headers that were encapsulated by either FOU
or GUE. Without this patch I was barely able to get 1 Gb/s of throughput.
With this patch applied I am now at least getting around 6 Gb/s.
The issue is due to the fact that with FOU or GUE applied we do not provide
a transport offset pointing to the GRE header, nor do we offload it in
software as the GRE header is completely skipped by GSO and treated like a
VXLAN or GENEVE type header. As such we need to prevent the stack from
generating it and also prevent GRE from generating it via any interface we
create.
Fixes:
c3483384ee511 ("gro: Allow tunnel stacking in the case of FOU/GUE")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Strashko, Grygorii [Wed, 6 Apr 2016 11:45:53 +0000 (14:45 +0300)]
PM / wakeirq: fix wakeirq setting after wakup re-configuration from sysfs
Now wakeirq stops working for device if wakeup option for
this device will be reconfigured through sysfs, like:
echo disabled > /sys/devices/platform/extcon_usb1/power/wakeup
echo enabled > /sys/devices/platform/extcon_usb1/power/wakeup
Once above set of commands is executed the device's wakeup_source
opject will be recreated and dev->power.wakeup->wakeirq field will
contain NULL. As result, device_wakeup_arm_wake_irqs() will not arm
wakeirq for the affected device.
Hece, lets try to fix it in the following way:
check for dev->wakeirq field when device_wakeup_attach() is called
and if !NULL re-attach wakeirq to the device
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Len Brown [Wed, 6 Apr 2016 21:16:00 +0000 (17:16 -0400)]
tools/power turbostat: work around RC6 counter wrap
Sometimes the rc6 sysfs counter spontaneously resets,
causing turbostat prints a very large number
as it tries to calcuate % = 100 * (old - new) / interval
When we see (old > new), print ***.**% instead
of a bogus huge number.
Note that this detection is not fool-proof, as the counter
could reset several times and still result in new > old.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Len Brown [Wed, 6 Apr 2016 21:15:59 +0000 (17:15 -0400)]
tools/power turbostat: initial KBL support
KBL is similar to SKL
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Len Brown [Wed, 6 Apr 2016 21:15:58 +0000 (17:15 -0400)]
tools/power turbostat: initial SKX support
SKX has a lot in common with HSX
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Len Brown [Wed, 6 Apr 2016 21:15:57 +0000 (17:15 -0400)]
tools/power turbostat: decode BXT TSC frequency via CPUID
Hard-code BXT ART to 19200MHz, so turbostat --debug
can fully enumerate TSC:
CPUID(0x15): eax_crystal: 3 ebx_tsc: 186 ecx_crystal_hz: 0
TSC: 1190 MHz (
19200000 Hz * 186 / 3 /
1000000)
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Len Brown [Wed, 6 Apr 2016 21:15:56 +0000 (17:15 -0400)]
tools/power turbostat: initial BXT support
Broxton has a lot in common with SKL
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Len Brown [Wed, 6 Apr 2016 21:15:55 +0000 (17:15 -0400)]
tools/power turbostat: print IRTL MSRs
Some processors use the Interrupt Response Time Limit (IRTL) MSR value
to describe the maximum IRQ response time latency for deep
package C-states. (Though others have the register, but do not use it)
Lets print it out to give insight into the cases where it is used.
IRTL begain in SNB, with PC3/PC6/PC7, and HSW added PC8/PC9/PC10.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Len Brown [Wed, 6 Apr 2016 21:15:54 +0000 (17:15 -0400)]
tools/power turbostat: SGX state should print only if --debug
The CPUID.SGX bit was printed, even if --debug was used
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Len Brown [Wed, 6 Apr 2016 21:00:59 +0000 (17:00 -0400)]
intel_idle: Add KBL support
KBL is similar to SKL
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Len Brown [Wed, 6 Apr 2016 21:00:58 +0000 (17:00 -0400)]
intel_idle: Add SKX support
SKX is similar to BDX
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Richard Cochran [Wed, 6 Apr 2016 21:00:57 +0000 (17:00 -0400)]
intel_idle: Clean up all registered devices on exit.
This driver registers cpuidle devices when a CPU comes online, but it
leaves the registrations in place when a CPU goes offline. The module
exit code only unregisters the currently online CPUs, leaving the
devices for offline CPUs dangling.
This patch changes the driver to clean up all registrations on exit,
even those from CPUs that are offline.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Richard Cochran [Wed, 6 Apr 2016 21:00:56 +0000 (17:00 -0400)]
intel_idle: Propagate hot plug errors.
If a cpuidle registration error occurs during the hot plug notifier
callback, we should really inform the hot plug machinery instead of
just ignoring the error. This patch changes the callback to properly
return on error.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Richard Cochran [Wed, 6 Apr 2016 21:00:55 +0000 (17:00 -0400)]
intel_idle: Don't overreact to a cpuidle registration failure.
The helper function, intel_idle_cpu_init, registers one new device
with the cpuidle layer. If the registration should fail, that
function immediately calls intel_idle_cpuidle_devices_uninit() to
unregister every last CPU's device. However, it makes no sense to do
so, when called from the hot plug notifier callback.
This patch moves the call to intel_idle_cpuidle_devices_uninit()
outside of the helper function to the one call site that actually
needs to perform the de-registrations.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Richard Cochran [Wed, 6 Apr 2016 21:00:54 +0000 (17:00 -0400)]
intel_idle: Setup the timer broadcast only on successful driver load.
This driver sets the broadcast tick quite early on during probe and does
not clean up again in cast of failure. This patch moves the setup call
after the registration, placing the on_each_cpu() calls within the global
CPU lock region.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Richard Cochran [Wed, 6 Apr 2016 21:00:53 +0000 (17:00 -0400)]
intel_idle: Avoid a double free of the per-CPU data.
The helper function, intel_idle_cpuidle_devices_uninit, frees the
globally allocated per-CPU data. However, this function is invoked
from the hot plug notifier callback at a time when freeing that data
is not safe.
If the call to cpuidle_register_driver() should fail (say, due to lack
of memory), then the driver will free its per-CPU region. On the
*next* CPU_ONLINE event, the driver will happily use the region again
and even free it again if the failure repeats.
This patch fixes the issue by moving the call to free_percpu() outside
of the helper function at the two call sites that actually need to
free the per-CPU data.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Richard Cochran [Wed, 6 Apr 2016 21:00:52 +0000 (17:00 -0400)]
intel_idle: Fix dangling registration on error path.
In the module_init() method, if the per-CPU allocation fails, then the
active cpuidle registration is not cleaned up. This patch fixes the
issue by attempting the allocation before registration, and then
cleaning it up again on registration failure.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Richard Cochran [Wed, 6 Apr 2016 21:00:51 +0000 (17:00 -0400)]
intel_idle: Fix deallocation order on the driver exit path.
In the module_exit() method, this driver first frees its per-CPU
pointer, then unregisters a callback making use of the pointer.
Furthermore, the function, intel_idle_cpuidle_devices_uninit, is racy
against CPU hot plugging as it calls for_each_online_cpu().
This patch corrects the issues by unregistering first on the exit path
while holding the hot plug lock.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Richard Cochran [Wed, 6 Apr 2016 21:00:50 +0000 (17:00 -0400)]
intel_idle: Remove redundant initialization calls.
The function, intel_idle_cpuidle_driver_init, makes calls on each CPU
to auto_demotion_disable() and c1e_promotion_disable(). These calls
are redundant, as intel_idle_cpu_init() does the same calls just a bit
later on. They are also premature, as the driver registration may yet
fail.
This patch removes the redundant code.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Richard Cochran [Wed, 6 Apr 2016 21:00:49 +0000 (17:00 -0400)]
intel_idle: Fix a helper function's return value.
The function, intel_idle_cpuidle_driver_init, delivers no error codes
at all. This patch changes the function to return 'void' instead of
returning zero.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Richard Cochran [Wed, 6 Apr 2016 21:00:48 +0000 (17:00 -0400)]
intel_idle: remove useless return from void function.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Jozsef Kadlecsik [Wed, 30 Mar 2016 09:34:35 +0000 (11:34 +0200)]
netfilter: nf_conntrack_tcp: Fix stack out of bounds when parsing TCP options
Baozeng Ding reported a KASAN stack out of bounds issue - it uncovered that
the TCP option parsing routines in netfilter TCP connection tracking could
read one byte out of the buffer of the TCP options. Therefore in the patch
we check that the available data length is large enough to parse both TCP
option code and size.
Reported-by: Baozeng Ding <sploving1@gmail.com>
Tested-by: Baozeng Ding <sploving1@gmail.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Greg Kroah-Hartman [Thu, 7 Apr 2016 15:31:43 +0000 (08:31 -0700)]
Merge tag 'fixes-for-v4.6-rc3' of git://git./linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.6-rc3
We have two more fixes to f_midi. It should now
behave much better.
dwc3-keystone.c has gotten a fix which now allows it
to work on keystone device when running in
peripheral mode. A similar fix for DMA configuration
was made for udc-core, too.
We have a new PCI ID for Intel's Broxton
platform. DWC3 can run on those platforms as well.
And we also have some dwc2 got a fix for dr_mode
usage, while renesas controller got 3 important
fixes: a NULL pointer deref fix, IRQ <-> DMA race
fix, and a fix to prevent a situation where we would
queue a request to a disabled endpoint.
Dan Carpenter [Wed, 6 Apr 2016 18:38:56 +0000 (21:38 +0300)]
iommu/vt-d: Silence an uninitialized variable warning
My static checker complains that "dma_alias" is uninitialized unless we
are dealing with a pci device. This is true but harmless. Anyway, we
can flip the condition around to silence the warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
John Keeping [Tue, 5 Apr 2016 14:05:46 +0000 (15:05 +0100)]
iommu/rockchip: Fix "is stall active" check
Since commit
cd6438c5f844 ("iommu/rockchip: Reconstruct to support multi
slaves") rk_iommu_is_stall_active() always returns false because the
bitwise AND operates on the boolean flag promoted to an integer and a
value that is either zero or BIT(2).
Explicitly convert the right-hand value to a boolean so that both sides
are guaranteed to be either zero or one.
rk_iommu_is_paging_enabled() does not suffer from the same problem since
RK_MMU_STATUS_PAGING_ENABLED is BIT(0), but let's apply the same change
for consistency and to make it clear that it's correct without needing
to lookup the value.
Fixes:
cd6438c5f844 ("iommu/rockchip: Reconstruct to support multi slaves")
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Joerg Roedel [Mon, 4 Apr 2016 13:47:48 +0000 (15:47 +0200)]
iommu: Don't overwrite domain pointer when there is no default_domain
IOMMU drivers that do not support default domains, but make
use of the the group->domain pointer can get that pointer
overwritten with NULL on device add/remove.
Make sure this can't happen by only overwriting the domain
pointer when it is NULL.
Cc: stable@vger.kernel.org # v4.4+
Fixes:
1228236de5f9 ('iommu: Move default domain allocation to iommu_group_get_for_dev()')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Stefan Hajnoczi [Tue, 29 Mar 2016 15:43:45 +0000 (16:43 +0100)]
virtio: add VIRTIO_CONFIG_S_NEEDS_RESET device status bit
The VIRTIO 1.0 specification added the DEVICE_NEEDS_RESET device status
bit in "VIRTIO-98: Add DEVICE_NEEDS_RESET". This patch defines the
device status bit in the uapi header file so that both the kernel and
userspace applications can use it.
The bit is currently unused by the virtio guest drivers and vhost.
According to the spec "a good implementation will try to recover by
issuing a reset". This is not attempted here because it requires
auditing the virtio drivers to ensure there are no resource leaks or
crashes if the device needs to be reset mid-operation.
See "2.1 Device Status Field" in the VIRTIO 1.0 specification for
details.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Michael S. Tsirkin [Tue, 5 Apr 2016 08:26:44 +0000 (11:26 +0300)]
MAINTAINERS: add entry for QEMU
Gabriel merged support for QEMU FW CFG interface, but there's apparently
no official maintainer. It's also possible that this will grow more
interfaces in future. I'll happily co-maintain it and handle pull
requests together with the rest of the PV stuff I maintain.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Gabriel Somlo <somlo@cmu.edu>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Gabriel Somlo <somlo@cmu.edu>
Gabriel Somlo [Tue, 8 Mar 2016 18:30:50 +0000 (13:30 -0500)]
firmware: qemu_fw_cfg.c: hold ACPI global lock during device access
Allowing for the future possibility of implementing AML-based
(i.e., firmware-triggered) access to the QEMU fw_cfg device,
acquire the global ACPI lock when accessing the device on behalf
of the guest-side sysfs driver, to prevent any potential race
conditions.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Michael S. Tsirkin [Sun, 3 Apr 2016 12:23:37 +0000 (15:23 +0300)]
virtio: virtio 1.0 cs04 spec compliance for reset
The spec says: after writing 0 to device_status, the driver MUST wait
for a read of device_status to return 0 before reinitializing the
device.
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Michael S. Tsirkin [Sun, 3 Apr 2016 12:22:08 +0000 (15:22 +0300)]
qemu_fw_cfg: don't leak kobj on init error
If platform_driver_register fails, we should
cleanup fw_cfg_top_ko before exiting.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Gabriel Somlo <somlo@cmu.edu>
Bjørn Mork [Thu, 7 Apr 2016 10:09:17 +0000 (12:09 +0200)]
USB: option: add "D-Link DWM-221 B1" device id
Thomas reports:
"Windows:
00 diagnostics
01 modem
02 at-port
03 nmea
04 nic
Linux:
T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2001 ProdID=7e19 Rev=02.32
S: Manufacturer=Mobile Connect
S: Product=Mobile Connect
S: SerialNumber=
0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage"
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Florian Westphal [Tue, 29 Mar 2016 09:05:16 +0000 (11:05 +0200)]
netfilter: arp_tables: register table in initns
arptables is broken since we didn't register the table anymore --
even 'arptables -L' fails.
Fixes:
b9e69e127397187b ("netfilter: xtables: don't hook tables by default")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Martyn Welch [Tue, 29 Mar 2016 16:47:29 +0000 (17:47 +0100)]
USB: serial: cp210x: Adding GE Healthcare Device ID
The CP2105 is used in the GE Healthcare Remote Alarm Box, with the
Manufacturer ID of 0x1901 and Product ID of 0x0194.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Josh Boyer [Thu, 10 Mar 2016 14:48:52 +0000 (09:48 -0500)]
USB: serial: ftdi_sio: Add support for ICP DAS I-756xU devices
A Fedora user reports that the ftdi_sio driver works properly for the
ICP DAS I-7561U device. Further, the user manual for these devices
instructs users to load the driver and add the ids using the sysfs
interface.
Add support for these in the driver directly so that the devices work
out of the box instead of needing manual configuration.
Reported-by: <thesource@mail.ru>
CC: stable <stable@vger.kernel.org>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Filipe Manana [Wed, 30 Mar 2016 22:37:21 +0000 (23:37 +0100)]
Btrfs: fix file/data loss caused by fsync after rename and new inode
If we rename an inode A (be it a file or a directory), create a new
inode B with the old name of inode A and under the same parent directory,
fsync inode B and then power fail, at log tree replay time we end up
removing inode A completely. If inode A is a directory then all its files
are gone too.
Example scenarios where this happens:
This is reproducible with the following steps, taken from a couple of
test cases written for fstests which are going to be submitted upstream
soon:
# Scenario 1
mkfs.btrfs -f /dev/sdc
mount /dev/sdc /mnt
mkdir -p /mnt/a/x
echo "hello" > /mnt/a/x/foo
echo "world" > /mnt/a/x/bar
sync
mv /mnt/a/x /mnt/a/y
mkdir /mnt/a/x
xfs_io -c fsync /mnt/a/x
<power failure happens>
The next time the fs is mounted, log tree replay happens and
the directory "y" does not exist nor do the files "foo" and
"bar" exist anywhere (neither in "y" nor in "x", nor the root
nor anywhere).
# Scenario 2
mkfs.btrfs -f /dev/sdc
mount /dev/sdc /mnt
mkdir /mnt/a
echo "hello" > /mnt/a/foo
sync
mv /mnt/a/foo /mnt/a/bar
echo "world" > /mnt/a/foo
xfs_io -c fsync /mnt/a/foo
<power failure happens>
The next time the fs is mounted, log tree replay happens and the
file "bar" does not exists anymore. A file with the name "foo"
exists and it matches the second file we created.
Another related problem that does not involve file/data loss is when a
new inode is created with the name of a deleted snapshot and we fsync it:
mkfs.btrfs -f /dev/sdc
mount /dev/sdc /mnt
mkdir /mnt/testdir
btrfs subvolume snapshot /mnt /mnt/testdir/snap
btrfs subvolume delete /mnt/testdir/snap
rmdir /mnt/testdir
mkdir /mnt/testdir
xfs_io -c fsync /mnt/testdir # or fsync some file inside /mnt/testdir
<power failure>
The next time the fs is mounted the log replay procedure fails because
it attempts to delete the snapshot entry (which has dir item key type
of BTRFS_ROOT_ITEM_KEY) as if it were a regular (non-root) entry,
resulting in the following error that causes mount to fail:
[52174.510532] BTRFS info (device dm-0): failed to delete reference to snap, inode 257 parent 257
[52174.512570] ------------[ cut here ]------------
[52174.513278] WARNING: CPU: 12 PID: 28024 at fs/btrfs/inode.c:3986 __btrfs_unlink_inode+0x178/0x351 [btrfs]()
[52174.514681] BTRFS: Transaction aborted (error -2)
[52174.515630] Modules linked in: btrfs dm_flakey dm_mod overlay crc32c_generic ppdev xor raid6_pq acpi_cpufreq parport_pc tpm_tis sg parport tpm evdev i2c_piix4 proc
[52174.521568] CPU: 12 PID: 28024 Comm: mount Tainted: G W 4.5.0-rc6-btrfs-next-27+ #1
[52174.522805] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS by qemu-project.org 04/01/2014
[52174.524053]
0000000000000000 ffff8801df2a7710 ffffffff81264e93 ffff8801df2a7758
[52174.524053]
0000000000000009 ffff8801df2a7748 ffffffff81051618 ffffffffa03591cd
[52174.524053]
00000000fffffffe ffff88015e6e5000 ffff88016dbc3c88 ffff88016dbc3c88
[52174.524053] Call Trace:
[52174.524053] [<
ffffffff81264e93>] dump_stack+0x67/0x90
[52174.524053] [<
ffffffff81051618>] warn_slowpath_common+0x99/0xb2
[52174.524053] [<
ffffffffa03591cd>] ? __btrfs_unlink_inode+0x178/0x351 [btrfs]
[52174.524053] [<
ffffffff81051679>] warn_slowpath_fmt+0x48/0x50
[52174.524053] [<
ffffffffa03591cd>] __btrfs_unlink_inode+0x178/0x351 [btrfs]
[52174.524053] [<
ffffffff8118f5e9>] ? iput+0xb0/0x284
[52174.524053] [<
ffffffffa0359fe8>] btrfs_unlink_inode+0x1c/0x3d [btrfs]
[52174.524053] [<
ffffffffa038631e>] check_item_in_log+0x1fe/0x29b [btrfs]
[52174.524053] [<
ffffffffa0386522>] replay_dir_deletes+0x167/0x1cf [btrfs]
[52174.524053] [<
ffffffffa038739e>] fixup_inode_link_count+0x289/0x2aa [btrfs]
[52174.524053] [<
ffffffffa038748a>] fixup_inode_link_counts+0xcb/0x105 [btrfs]
[52174.524053] [<
ffffffffa038a5ec>] btrfs_recover_log_trees+0x258/0x32c [btrfs]
[52174.524053] [<
ffffffffa03885b2>] ? replay_one_extent+0x511/0x511 [btrfs]
[52174.524053] [<
ffffffffa034f288>] open_ctree+0x1dd4/0x21b9 [btrfs]
[52174.524053] [<
ffffffffa032b753>] btrfs_mount+0x97e/0xaed [btrfs]
[52174.524053] [<
ffffffff8108e1b7>] ? trace_hardirqs_on+0xd/0xf
[52174.524053] [<
ffffffff8117bafa>] mount_fs+0x67/0x131
[52174.524053] [<
ffffffff81193003>] vfs_kern_mount+0x6c/0xde
[52174.524053] [<
ffffffffa032af81>] btrfs_mount+0x1ac/0xaed [btrfs]
[52174.524053] [<
ffffffff8108e1b7>] ? trace_hardirqs_on+0xd/0xf
[52174.524053] [<
ffffffff8108c262>] ? lockdep_init_map+0xb9/0x1b3
[52174.524053] [<
ffffffff8117bafa>] mount_fs+0x67/0x131
[52174.524053] [<
ffffffff81193003>] vfs_kern_mount+0x6c/0xde
[52174.524053] [<
ffffffff8119590f>] do_mount+0x8a6/0x9e8
[52174.524053] [<
ffffffff811358dd>] ? strndup_user+0x3f/0x59
[52174.524053] [<
ffffffff81195c65>] SyS_mount+0x77/0x9f
[52174.524053] [<
ffffffff814935d7>] entry_SYSCALL_64_fastpath+0x12/0x6b
[52174.561288] ---[ end trace
6b53049efb1a3ea6 ]---
Fix this by forcing a transaction commit when such cases happen.
This means we check in the commit root of the subvolume tree if there
was any other inode with the same reference when the inode we are
fsync'ing is a new inode (created in the current transaction).
Test cases for fstests, covering all the scenarios given above, were
submitted upstream for fstests:
* fstests: generic test for fsync after renaming directory
https://patchwork.kernel.org/patch/
8694281/
* fstests: generic test for fsync after renaming file
https://patchwork.kernel.org/patch/
8694301/
* fstests: add btrfs test for fsync after snapshot deletion
https://patchwork.kernel.org/patch/
8670671/
Cc: stable@vger.kernel.org
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Chris Mason [Wed, 6 Apr 2016 23:57:19 +0000 (16:57 -0700)]
Merge branch 'misc-4.6' of git://git./linux/kernel/git/kdave/linux into for-linus-4.6
Shanker Donthineni [Wed, 6 Apr 2016 17:49:24 +0000 (12:49 -0500)]
mailbox: pcc: Don't access an unmapped memory address space
The acpi_pcc_probe() may end up accessing memory outside of the PCCT
table space causing the kernel panic(). Increment the pcct_entry
pointer after parsing 'HW-reduced Communications Subspace' to fix
the problem. This change also enables the parsing of subtable at
index 0.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Acked-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Dave Airlie [Wed, 6 Apr 2016 21:08:46 +0000 (07:08 +1000)]
Merge branch 'drm-fixes-4.6' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Lots of misc bug fixes for radeon and amdgpu and one for ttm.
- fix vram info fetching on Fiji and unposted boards
- additional vblank fixes from the conversion to drm_vblank_on/off
- UVD dGPU suspend and resume fixes
- lots of powerplay fixes
- fix a fence leak in the pageflip code
- ttm fix for platforms where CPU is 32 bit, but physical addresses are >32bits
* 'drm-fixes-4.6' of git://people.freedesktop.org/~agd5f/linux: (21 commits)
drm/amdgpu: total vram size also reduces pin size
drm/amd/powerplay: add uvd/vce dpm enabling flag default.
drm/amd/powerplay: fix issue that resume back, dpm can't work on FIJI.
drm/amdgpu: save and restore the firwmware cache part when suspend resume
drm/amdgpu: save and restore UVD context with suspend and resume
drm/ttm: use phys_addr_t for ttm_bus_placement
drm/radeon: Only call drm_vblank_on/off between drm_vblank_init/cleanup
drm/amdgpu: fence wait old rcu slot
drm/amdgpu: fix leaking fence in the pageflip code
drm/amdgpu: print vram type rather than just DDR
drm/amdgpu/gmc: use proper register for vram type on Fiji
drm/amdgpu/gmc: move vram type fetching into sw_init
drm/amdgpu: Set vblank_disable_allowed = true
drm/radeon: Set vblank_disable_allowed = true
drm/amd/powerplay: Need to change boot to performance state in resume.
drm/amd/powerplay: add new Fiji function for not setting same ps.
drm/amdgpu: check dpm state before pm system fs initialized.
drm/amd/powerplay: notify amdgpu whether dpm is enabled or not.
drm/amdgpu: Not support disable dpm in powerplay.
drm/amdgpu: add an cgs interface to notify amdgpu the dpm state.
...
Dexuan Cui [Tue, 5 Apr 2016 14:41:11 +0000 (07:41 -0700)]
net: add the AF_KCM entries to family name tables
This is for the recent kcm driver, which introduces AF_KCM(41) in
b7ac4eb(kcm: Kernel Connection Multiplexor module).
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc [Tue, 5 Apr 2016 14:39:37 +0000 (16:39 +0200)]
MAINTAINERS: intel-wired-lan list is moderated
I got the following message:
> Your mail to 'Intel-wired-lan' with the subject
>
> [PATCH net-next] net: intel: remove dead links
>
> Is being held until the list moderator can review it for approval.
>
> The reason it is being held:
>
> Post by non-member to a members-only list
Mark the list as moderated.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Naveen N. Rao [Tue, 5 Apr 2016 10:02:56 +0000 (15:32 +0530)]
lib/test_bpf: Add additional BPF_ADD tests
Some of these tests proved useful with the powerpc eBPF JIT port due to
sign-extended 16-bit immediate loads. Though some of these aspects get
covered in other tests, it is better to have explicit tests so as to
quickly tag the precise problem.
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Naveen N. Rao [Tue, 5 Apr 2016 10:02:55 +0000 (15:32 +0530)]
lib/test_bpf: Add test to check for result of 32-bit add that overflows
BPF_ALU32 and BPF_ALU64 tests for adding two 32-bit values that results in
32-bit overflow.
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Naveen N. Rao [Tue, 5 Apr 2016 10:02:54 +0000 (15:32 +0530)]
lib/test_bpf: Add tests for unsigned BPF_JGT
Unsigned Jump-if-Greater-Than.
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Naveen N. Rao [Tue, 5 Apr 2016 10:02:53 +0000 (15:32 +0530)]
lib/test_bpf: Fix JMP_JSET tests
JMP_JSET tests incorrectly used BPF_JNE. Fix the same.
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 6 Apr 2016 20:45:07 +0000 (13:45 -0700)]
x86: remove the kernel code/data/bss resources from /proc/iomem
Let's see if anybody even notices. I doubt anybody uses this, and it
does expose addresses that should be randomized, so let's just remove
the code. It's old and traditional, and it used to be cute, but we
should have removed this long ago.
If it turns out anybody notices and this breaks something, we'll have to
revert this, and maybe we'll end up using other approaches instead
(using %pK or similar). But removing unnecessary code is always the
preferred option.
Noted-by: Emrah Demir <ed@abdsec.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jorgen Hansen [Tue, 5 Apr 2016 08:59:32 +0000 (01:59 -0700)]
VSOCK: Detach QP check should filter out non matching QPs.
The check in vmci_transport_peer_detach_cb should only allow a
detach when the qp handle of the transport matches the one in
the detach message.
Testing: Before this change, a detach from a peer on a different
socket would cause an active stream socket to register a detach.
Reviewed-by: George Zhang <georgezhang@vmware.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Giuseppe CAVALLARO [Tue, 5 Apr 2016 06:46:57 +0000 (08:46 +0200)]
stmmac: fix adjust link call in case of a switch is attached
While initializing the phy, the stmmac driver sets the
PHY_IGNORE_INTERRUPT so the PAL won't call the adjust hook
that is needed, on some platforms, e.g. STi, to invoke the glue.
The patch allows the PAL to poll the stmmac_adjust_link just one time
in case of a switch is attached, setting later the PHY_IGNORE_INTERRUPT
flag.
Moving this kind of logic inside the adjust_link it makes sense to
anticipate the check for EEE that will never initialized in this
scenario.
Reported-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Tested-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Jones [Mon, 4 Apr 2016 19:11:50 +0000 (15:11 -0400)]
af_packet: tone down the Tx-ring unsupported spew.
Trinity and other fuzzers can hit this WARN on far too easily,
resulting in a tainted kernel that hinders automated fuzzing.
Replace it with a rate-limited printk.
Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Mon, 4 Apr 2016 17:32:48 +0000 (10:32 -0700)]
net_sched: fix a memory leak in tc action
Fixes:
ddf97ccdd7cb ("net_sched: add network namespace support for tc actions")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Naveen N. Rao [Mon, 4 Apr 2016 17:01:34 +0000 (22:31 +0530)]
samples/bpf: Enable powerpc support
Add the necessary definitions for building bpf samples on ppc.
Since ppc doesn't store function return address on the stack, modify how
PT_REGS_RET() and PT_REGS_FP() work.
Also, introduce PT_REGS_IP() to access the instruction pointer.
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Naveen N. Rao [Mon, 4 Apr 2016 17:01:33 +0000 (22:31 +0530)]
samples/bpf: Use llc in PATH, rather than a hardcoded value
While at it, remove the generation of .s files and fix some typos in the
related comment.
Cc: Alexei Starovoitov <ast@fb.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Naveen N. Rao [Mon, 4 Apr 2016 17:01:32 +0000 (22:31 +0530)]
samples/bpf: Fix build breakage with map_perf_test_user.c
Building BPF samples is failing with the below error:
samples/bpf/map_perf_test_user.c: In function ‘main’:
samples/bpf/map_perf_test_user.c:134:9: error: variable ‘r’ has
initializer but incomplete type
struct rlimit r = {RLIM_INFINITY, RLIM_INFINITY};
^
samples/bpf/map_perf_test_user.c:134:21: error: ‘RLIM_INFINITY’
undeclared (first use in this function)
struct rlimit r = {RLIM_INFINITY, RLIM_INFINITY};
^
samples/bpf/map_perf_test_user.c:134:21: note: each undeclared
identifier is reported only once for each function it appears in
samples/bpf/map_perf_test_user.c:134:9: warning: excess elements in
struct initializer [enabled by default]
struct rlimit r = {RLIM_INFINITY, RLIM_INFINITY};
^
samples/bpf/map_perf_test_user.c:134:9: warning: (near initialization
for ‘r’) [enabled by default]
samples/bpf/map_perf_test_user.c:134:9: warning: excess elements in
struct initializer [enabled by default]
samples/bpf/map_perf_test_user.c:134:9: warning: (near initialization
for ‘r’) [enabled by default]
samples/bpf/map_perf_test_user.c:134:16: error: storage size of ‘r’
isn’t known
struct rlimit r = {RLIM_INFINITY, RLIM_INFINITY};
^
samples/bpf/map_perf_test_user.c:139:2: warning: implicit declaration of
function ‘setrlimit’ [-Wimplicit-function-declaration]
setrlimit(RLIMIT_MEMLOCK, &r);
^
samples/bpf/map_perf_test_user.c:139:12: error: ‘RLIMIT_MEMLOCK’
undeclared (first use in this function)
setrlimit(RLIMIT_MEMLOCK, &r);
^
samples/bpf/map_perf_test_user.c:134:16: warning: unused variable ‘r’
[-Wunused-variable]
struct rlimit r = {RLIM_INFINITY, RLIM_INFINITY};
^
make[2]: *** [samples/bpf/map_perf_test_user.o] Error 1
Fix this by including the necessary header file.
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / GitHub / moto-9609 / android_kernel_motorola_exynos9610.git / log