GitHub/exynos8895/android_kernel_samsung_universal8895.git
10 years agowlcore/wl18xx/wl12xx: convert bitmaps to unsigned longs
Eliad Peller [Fri, 11 Jul 2014 00:01:39 +0000 (03:01 +0300)]
wlcore/wl18xx/wl12xx: convert bitmaps to unsigned longs

The *_bit operations expect unsigned longs.
Instead of casting the pointers, simply define various
bitmaps as unsigned long (instead of u32).

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agowl18xx: make sure fw_status->priv exists before deref
Eliad Peller [Fri, 11 Jul 2014 00:01:38 +0000 (03:01 +0300)]
wl18xx: make sure fw_status->priv exists before deref

In some corner cases with specific timings, we might
try dequeueing tx before we got information about
the link status (e.g. due to recovery during tx).

Instead of NULL dereference, assume all
the links in this case have low priorities.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agowl18xx: change the number of WLAN addrs per chip
Arik Nemtsov [Fri, 11 Jul 2014 00:01:37 +0000 (03:01 +0300)]
wl18xx: change the number of WLAN addrs per chip

Each 18xx chip contains only 2 real MAC addresses
usable for WLAN, forcing us to use the LAA bit
approach to obtain a third MAC address.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agowlcore: don't switch channels on disconnected STA vifs
Arik Nemtsov [Fri, 11 Jul 2014 00:01:36 +0000 (03:01 +0300)]
wlcore: don't switch channels on disconnected STA vifs

Sending the FW a channel switch command on a disconnected
vif may result in a beacon loss event. Avoid this corner case.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agowlcore: register vendor commands
Eliad Peller [Fri, 11 Jul 2014 00:01:35 +0000 (03:01 +0300)]
wlcore: register vendor commands

All the smart config code is in place now,
so register the relevant vendor commands.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agowlcore: increase max roc duration to 30 seconds
Eliad Peller [Fri, 11 Jul 2014 00:01:34 +0000 (03:01 +0300)]
wlcore: increase max roc duration to 30 seconds

we don't have any actual limitation in the driver, so
increase it arbitrarily to 30 seconds.

The long ROC is needed for the smart config.flow.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agowlcore/wl18xx: handle smart config events
Eliad Peller [Fri, 11 Jul 2014 00:01:33 +0000 (03:01 +0300)]
wlcore/wl18xx: handle smart config events

add defintions and handling for smart config events
(SMART_CONFIG_SYNC_EVENT_ID and SMART_CONFIG_DECODE_EVENT_ID)

parse the relevant info and send it to userspace as
vendor event.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agowlcore: handle smart config vendor commands
Eliad Peller [Fri, 11 Jul 2014 00:01:32 +0000 (03:01 +0300)]
wlcore: handle smart config vendor commands

userspace can ask to perform various smart config
actions via custom vendor commands.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agowlcore/wl18xx: add smart config commands
Eliad Peller [Fri, 11 Jul 2014 00:01:31 +0000 (03:01 +0300)]
wlcore/wl18xx: add smart config commands

These commands configures the fw to set key,
enter smart config mode, and exit it.

Add relevant hw ops as well.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agowlcore: add smart config definitions
Eliad Peller [Fri, 11 Jul 2014 00:01:30 +0000 (03:01 +0300)]
wlcore: add smart config definitions

Add definitions for the smart config commands.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agowlcore: use correct LAA bit
Eliad Peller [Fri, 11 Jul 2014 00:01:29 +0000 (03:01 +0300)]
wlcore: use correct LAA bit

The LAA bit is second bit of the MSB, not of the
third byte.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agowl18xx: fix last tx rate calculation
Eliad Peller [Fri, 11 Jul 2014 00:01:28 +0000 (03:01 +0300)]
wl18xx: fix last tx rate calculation

The last tx rate calculation didn't take into account
the different indices of 11a and 11g rates tables.

Add the required alignment (count only from the first
11a rate in case of 11a)

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agowlcore: user smaller sqn padding for GEM
Eliad Peller [Fri, 11 Jul 2014 00:01:27 +0000 (03:01 +0300)]
wlcore: user smaller sqn padding for GEM

On recovery, we increase the current seq num by
WL1271_TX_SQN_POST_RECOVERY_PADDING in order to
compensate for packets we might have missed during
recovery.

It seems that some GEM APs have issues when the
gap is too big, so use a smaller padding in this case.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agowlcore: save seq num only between recoveries
Eliad Peller [Fri, 11 Jul 2014 00:01:26 +0000 (03:01 +0300)]
wlcore: save seq num only between recoveries

We want seq num (freed_pkts) to be initialized
on each new connection, but keep persistent
between recoveries/suspends.

Save the freed_pkts in the private block of the
sta struct (we already do a similar thing for
AP's stations).

However, keep the old wlvif->total_freed_pkts
in order to avoid too intrusive change.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agob43: don't warn about no 5 GHz support on 2.4 GHz devices
Rafał Miłecki [Tue, 8 Jul 2014 19:00:19 +0000 (21:00 +0200)]
b43: don't warn about no 5 GHz support on 2.4 GHz devices

This could be a bit confusing to see warning about lacking support for
5 GHz band if your device supports 2.4 GHz only.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agob43: enable radio 0x2057 rev 9 (AKA BCM43228) support
Rafał Miłecki [Tue, 8 Jul 2014 13:11:10 +0000 (15:11 +0200)]
b43: enable radio 0x2057 rev 9 (AKA BCM43228) support

Support for N-PHY rev 8 with 0x2057 rev 5 is almost ready, but we still
need to figure out how to handle rev 9 first.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agob43: N-PHY: implement channel switching of radio 0x2057 rev 5
Rafał Miłecki [Tue, 8 Jul 2014 13:11:09 +0000 (15:11 +0200)]
b43: N-PHY: implement channel switching of radio 0x2057 rev 5

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agob43: N-PHY: init and channel switching of radio 0x2057 rev 9
Rafał Miłecki [Tue, 8 Jul 2014 13:11:08 +0000 (15:11 +0200)]
b43: N-PHY: init and channel switching of radio 0x2057 rev 9

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agob43; N-PHY: write most of the missing code for revs 7+
Rafał Miłecki [Tue, 8 Jul 2014 13:11:07 +0000 (15:11 +0200)]
b43; N-PHY: write most of the missing code for revs 7+

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agob43: N-PHY: add placeholders for new devices support
Rafał Miłecki [Tue, 8 Jul 2014 13:11:06 +0000 (15:11 +0200)]
b43: N-PHY: add placeholders for new devices support

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agob43: N-PHY: add TX gain tables for devices with specific EPA
Rafał Miłecki [Tue, 8 Jul 2014 13:11:05 +0000 (15:11 +0200)]
b43: N-PHY: add TX gain tables for devices with specific EPA

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agob43: N-PHY: drop reg 0x1 access restriction on new PHY revs
Rafał Miłecki [Tue, 8 Jul 2014 13:11:04 +0000 (15:11 +0200)]
b43: N-PHY: drop reg 0x1 access restriction on new PHY revs

Initialization of N-PHY radio revs 5 and 7 requires writing to 0x1.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agob43: always print info about radio (manuf, id, revision)
Rafał Miłecki [Wed, 2 Jul 2014 17:07:43 +0000 (19:07 +0200)]
b43: always print info about radio (manuf, id, revision)

Type of radio has a major meaning for the driver. There is quite some
code that does initialization/calibration depending on the radio rev.
Knowing radio params is quite important to provide help to users, so
print it even with debugging disabled.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agoMerge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetoot...
John W. Linville [Thu, 10 Jul 2014 21:00:34 +0000 (17:00 -0400)]
Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth-next

10 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville [Thu, 10 Jul 2014 21:00:24 +0000 (17:00 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless

10 years agoBluetooth: Don't send ERTM configuration option when disabled
Marcel Holtmann [Wed, 9 Jul 2014 09:53:35 +0000 (11:53 +0200)]
Bluetooth: Don't send ERTM configuration option when disabled

When ERTM support is disabled, then do not even send ERTM configuration
option even if the remote side supports it.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Fix setting HCI_CONNECTABLE from ioctl code
Johan Hedberg [Wed, 9 Jul 2014 10:28:26 +0000 (13:28 +0300)]
Bluetooth: Fix setting HCI_CONNECTABLE from ioctl code

When the white list is in use the code would not update the
HCI_CONNECTABLE flag if it gets changed through the ioctl code (e.g.
hciconfig hci0 pscan). Since the flag is important for properly
accepting incoming connections add code to fix it up if necessary and
emit a New Settings mgmt event.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Add white list lookup for incoming connection requests
Johan Hedberg [Wed, 9 Jul 2014 09:59:19 +0000 (12:59 +0300)]
Bluetooth: Add white list lookup for incoming connection requests

This patch adds support for looking up entries in the white list when
HCI_CONNECTABLE is not set. The logic is fairly simple: if we're
connectable check the black list, if we're not connectable check the
white list.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Enable page scan also if there are white list entries
Johan Hedberg [Wed, 9 Jul 2014 09:59:18 +0000 (12:59 +0300)]
Bluetooth: Enable page scan also if there are white list entries

Page scan should be enabled either if the connectable setting is set or
if there are any entries in the BR/EDR white list. This patch implements
such behavior by updating the two places that were making decisions on
whether to enable page scan or not.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Refactor connection request handling
Johan Hedberg [Wed, 9 Jul 2014 09:59:17 +0000 (12:59 +0300)]
Bluetooth: Refactor connection request handling

The conditions for accepting an incoming connections are already
non-trivial and will become more so once a white list is added. This
patch breaks up the checks for when to reject the request by creating a
helper function for it.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix incorrectly setting HCI_CONNECTABLE
Johan Hedberg [Wed, 9 Jul 2014 09:59:16 +0000 (12:59 +0300)]
Bluetooth: Fix incorrectly setting HCI_CONNECTABLE

Since page scan might be enabled by Add Device we should not implicitly
set connectable whenever something else than Set Connectable changes it.
This patch makes sure that we don't set HCI_CONNECTABLE for these cases
if there are any entries in the white list.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Update page scan when necessary for Add/Remove Device
Johan Hedberg [Wed, 9 Jul 2014 09:59:15 +0000 (12:59 +0300)]
Bluetooth: Update page scan when necessary for Add/Remove Device

When we're removing the last item in the white list or adding the first
one to it and HCI_CONNECTABLE is not set we need to update the current
page scan. This patch adds a simple helper function for the purpose and
calls it from the respective mgmt command handlers.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Introduce a whitelist for BR/EDR devices
Johan Hedberg [Wed, 9 Jul 2014 09:59:14 +0000 (12:59 +0300)]
Bluetooth: Introduce a whitelist for BR/EDR devices

This patch extends the Add/Remove device commands by letting user space
pass BR/EDR addresses to them. The resulting entries get stored in a new
hdev->whitelist list. The idea is that we can now selectively accept
connections from devices in the list even though HCI_CONNECTABLE is not
set (the actual implementation of this is coming in a subsequent patch).

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Unify helpers for bdaddr_list manipulations
Johan Hedberg [Wed, 9 Jul 2014 09:59:13 +0000 (12:59 +0300)]
Bluetooth: Unify helpers for bdaddr_list manipulations

We already have several lists with struct bdaddr_list entries, and there
will be more in the future. Since the operations for adding, removing,
looking up and clearing entries in these lists are exactly the same it
doesn't make sense to define new functions for every single list. This
patch unifies the functions by passing the list_head to them instead of
a hci_dev pointer.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix enabling Authenticated Payload Timeout Expired event
Marcel Holtmann [Wed, 9 Jul 2014 07:49:05 +0000 (09:49 +0200)]
Bluetooth: Fix enabling Authenticated Payload Timeout Expired event

The Authenticated Payload Timeout Expired event is valid for
controllers with BR/EDR Secure Connections support, but also for
LE only controllers supporting LE Ping feature. When either of them
is available enable this event. Previous it was not enabled when
the controller was only supporting LE operation.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Add support for Acer [13D3:3432]
Anantha Krishnan [Tue, 8 Jul 2014 13:55:08 +0000 (19:25 +0530)]
Bluetooth: Add support for Acer [13D3:3432]

Add support for the QCA6174 chip.

    T:  Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 30 Spd=12  MxCh= 0
    D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
    P:  Vendor=13d3 ProdID=3432 Rev=00.02
    C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
    I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
    I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Signed-off-by: Anantha Krishnan <ananthk@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix clearing HCI_LE_ADV for LE connections
Johan Hedberg [Tue, 8 Jul 2014 14:21:51 +0000 (17:21 +0300)]
Bluetooth: Fix clearing HCI_LE_ADV for LE connections

All LE controllers always implicitly stop advertising when establishing
connections. Therefore, be sure to clear the flag in the event handler
for new LE connections.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix toggling background scan when changing connectable state
Johan Hedberg [Tue, 8 Jul 2014 13:35:34 +0000 (16:35 +0300)]
Bluetooth: Fix toggling background scan when changing connectable state

If the connectable state change doesn't require any special HCI commands
the set_connectable_update_settings() function is used instead of the
set_connectable_complete() function. We must therefore make sure to call
hci_update_background_scan() there as well. This code path is used also
when we're powered off, but that's fine since hci_update_background_scan()
has the necessary checks for it.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix connectable and discoverable supported settings values
Johan Hedberg [Tue, 8 Jul 2014 13:07:34 +0000 (16:07 +0300)]
Bluetooth: Fix connectable and discoverable supported settings values

The connectable and discoverable mgmt settings are supported both for LE
and BR/EDR controllers so they do not belong behind a lmp_bredr_capable()
condition. This patch fixes the issue in get_supported_settings().

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix setting STOPPING state for discovery
Johan Hedberg [Tue, 8 Jul 2014 13:05:06 +0000 (16:05 +0300)]
Bluetooth: Fix setting STOPPING state for discovery

If any of the HCI commands from the hci_stop_discovery function were
successfully sent we need to set the discovery state to STOPPING. The
Stop Discovery code was already handling this, but the code in
clean_up_hci_state was not. This patch updates the hci_stop_discovery to
return a bool to indicate whether it queued any commands and the
clean_up_hci_state() function respectively to look at the return value
and call hci_discovery_set_state() if necessary.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix check for re-enabling advertising
Johan Hedberg [Tue, 8 Jul 2014 13:05:05 +0000 (16:05 +0300)]
Bluetooth: Fix check for re-enabling advertising

There are many different places that can disable LE scanning but we only
want to re-enable advertising in hci_cc_le_set_scan_enable() for a very
specific use case, which is when the active scanning part of Start
Discovery is complete. Because of this, fix the discovery state check to
test for the exact state.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix advertising and active scanning co-existence
Johan Hedberg [Tue, 8 Jul 2014 12:07:53 +0000 (15:07 +0300)]
Bluetooth: Fix advertising and active scanning co-existence

Many controllers allow simultaneous active scanning and advertising
(e.g. Intel and Broadcom) but some do not (e.g. CSR). It's therefore
safest to implement mutual exclusion of these states in the kernel.

This patch ensures that the two states are never entered simultaneously.
Extra precaution needs to be taken for outgoing connection attempts in
slave role (i.e. through directed advertising) in which case the
operation that came first has precedence and the one that comes after
gets a rejection.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Stop advertising always before initiating a connection
Johan Hedberg [Tue, 8 Jul 2014 12:07:52 +0000 (15:07 +0300)]
Bluetooth: Stop advertising always before initiating a connection

Most controllers do not support advertising while initiating an LE
connection. We also have to first disable current advertising if the
initiation is going to happen through direct advertising. Therefore,
simply stop advertising as the first thing when starting to issue
commands to establish an LE connection.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Use the correct flag to decide to disable advertising
Johan Hedberg [Tue, 8 Jul 2014 12:07:51 +0000 (15:07 +0300)]
Bluetooth: Use the correct flag to decide to disable advertising

When deciding to call disable_advertising() we're interested in the real
state instead of the mgmt setting. Use therefore HCI_LE_ADV instead of
the HCI_ADVERTISING flag.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Simplify usage of the enable_advertising function
Johan Hedberg [Tue, 8 Jul 2014 12:07:50 +0000 (15:07 +0300)]
Bluetooth: Simplify usage of the enable_advertising function

By adding support for disabling advertising when necessary and doing the
checks for existing LE connections inside the enable_advertising
function we can simplify the calling code quite a lot.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Use real advertising state to random address update decision
Johan Hedberg [Tue, 8 Jul 2014 12:07:49 +0000 (15:07 +0300)]
Bluetooth: Use real advertising state to random address update decision

Now that we have a flag for tracking the real advertising state we
should use that to determine whether it's safe to update the random
address or not. The couple of places that were clearing the flag due to
a pending request need to be updated too.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Remove unnecessary mgmt_advertising function
Johan Hedberg [Tue, 8 Jul 2014 12:07:48 +0000 (15:07 +0300)]
Bluetooth: Remove unnecessary mgmt_advertising function

Since the real advertising state is now tracked with its own flag we can
simply set/unset the HCI_ADVERTISING flag in the
set_advertising_complete function.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Add flag to track the real advertising state
Johan Hedberg [Tue, 8 Jul 2014 12:07:47 +0000 (15:07 +0300)]
Bluetooth: Add flag to track the real advertising state

Having a single HCI_ADVERTISING flag is problematic since it tries to
track both the real advertising state and the corresponding mgmt
setting. To make the logic simpler and more reliable add a new flag that
only tracks the actual advertising state that has been written to the
controller.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agobcma: add driver for PCIe Gen 2 core
Rafał Miłecki [Fri, 4 Jul 2014 23:10:41 +0000 (01:10 +0200)]
bcma: add driver for PCIe Gen 2 core

New Broadcom PCIe devices (802.11ac ones?) use Gen2 and have to be
initialized differently.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agob43: fix reading info about radio for new devices (cores 40 & 42)
Rafał Miłecki [Fri, 4 Jul 2014 07:21:56 +0000 (09:21 +0200)]
b43: fix reading info about radio for new devices (cores 40 & 42)

This changes
b43-phy0: Found Radio: Manuf 0x17F, Version 0x7769, Revision 4
to the
b43-phy0: Found Radio: Manuf 0x17F, Version 0x2069, Revision 4
which matches what closed source driver reports:
$ wl revinfo
radiorev 0x42069000

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agob43: N-PHY: add TX gains tables for radio 0x2057 rev 9
Rafał Miłecki [Wed, 2 Jul 2014 20:42:46 +0000 (22:42 +0200)]
b43: N-PHY: add TX gains tables for radio 0x2057 rev 9

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agob43: N-PHY: rework names & picking of TX gain tables
Rafał Miłecki [Wed, 2 Jul 2014 20:42:45 +0000 (22:42 +0200)]
b43: N-PHY: rework names & picking of TX gain tables

This allows adding more revisions support, spotting lacking tables and
unifies naming schema.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agob43: N-PHY: initialize hardware tables on new devices
Rafał Miłecki [Wed, 2 Jul 2014 15:05:35 +0000 (17:05 +0200)]
b43: N-PHY: initialize hardware tables on new devices

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agort2800usb: Don't perform DMA from stack
Andrea Merello [Sat, 5 Jul 2014 19:07:17 +0000 (21:07 +0200)]
rt2800usb: Don't perform DMA from stack

Function rt2800usb_autorun_detect() passes the address of a variable
allocated onto the stack to be used for DMA by the USB layer. This has
been caught by my debugging-enabled kernel.

This patch change things in order to allocate that variable via
kmalloc, and it adjusts things to handle the kmalloc failure case,
propagating the error.

[ 7363.238852] ------------[ cut here ]------------
[ 7363.243529] WARNING: CPU: 1 PID: 5235 at lib/dma-debug.c:1153 check_for_stack+0xa4/0xf0()
[ 7363.251759] ehci-pci 0000:00:04.1: DMA-API: device driver maps memory fromstack [addr=ffff88006b81bad4]
[ 7363.261210] Modules linked in: rt2800usb(O+) rt2800lib(O) rt2x00usb(O) rt2x00lib(O) rtl818x_pci(O) rtl8187 led_class eeprom_93cx6 mac80211 cfg80211 [last unloaded: rt2x00lib]
[ 7363.277143] CPU: 1 PID: 5235 Comm: systemd-udevd Tainted: G           O  3.16.0-rc3-wl+ #31
[ 7363.285546] Hardware name: System manufacturer System Product Name/M3N78 PRO, BIOS ASUS M3N78 PRO ACPI BIOS Revision 1402 12/04/2009
[ 7363.297511]  0000000000000009 ffff88006b81b710 ffffffff8175dcad ffff88006b81b758
[ 7363.305062]  ffff88006b81b748 ffffffff8106d372 ffff88006cf10098 ffff88006cead6a0
[ 7363.312622]  ffff88006b81bad4 ffffffff81c1e7c0 ffff88006cf10098 ffff88006b81b7a8
[ 7363.320161] Call Trace:
[ 7363.322661]  [<ffffffff8175dcad>] dump_stack+0x4d/0x6f
[ 7363.327847]  [<ffffffff8106d372>] warn_slowpath_common+0x82/0xb0
[ 7363.333893]  [<ffffffff8106d3e7>] warn_slowpath_fmt+0x47/0x50
[ 7363.339686]  [<ffffffff813a93b4>] check_for_stack+0xa4/0xf0
[ 7363.345298]  [<ffffffff813a995c>] debug_dma_map_page+0x10c/0x150
[ 7363.351367]  [<ffffffff81521bd9>] usb_hcd_map_urb_for_dma+0x229/0x720
[ 7363.357890]  [<ffffffff8152256d>] usb_hcd_submit_urb+0x2fd/0x930
[ 7363.363929]  [<ffffffff810eac31>] ? irq_work_queue+0x71/0xd0
[ 7363.369617]  [<ffffffff810ab5a7>] ? wake_up_klogd+0x37/0x50
[ 7363.375219]  [<ffffffff810ab7a5>] ? console_unlock+0x1e5/0x420
[ 7363.381081]  [<ffffffff810abc25>] ? vprintk_emit+0x245/0x530
[ 7363.386773]  [<ffffffff81523d3c>] usb_submit_urb+0x30c/0x580
[ 7363.392462]  [<ffffffff81524295>] usb_start_wait_urb+0x65/0xf0
[ 7363.398325]  [<ffffffff815243ed>] usb_control_msg+0xcd/0x110
[ 7363.404014]  [<ffffffffa005514d>] rt2x00usb_vendor_request+0xbd/0x170 [rt2x00usb]
[ 7363.411544]  [<ffffffffa0074292>] rt2800usb_autorun_detect+0x32/0x50 [rt2800usb]
[ 7363.418986]  [<ffffffffa0074aa1>] rt2800usb_read_eeprom+0x11/0x70 [rt2800usb]
[ 7363.426168]  [<ffffffffa0063ffd>] rt2800_probe_hw+0x11d/0xf90 [rt2800lib]
[ 7363.432989]  [<ffffffffa0074b7d>] rt2800usb_probe_hw+0xd/0x50 [rt2800usb]
[ 7363.439808]  [<ffffffffa00453d8>] rt2x00lib_probe_dev+0x238/0x7c0 [rt2x00lib]
[ 7363.446992]  [<ffffffffa00bfa48>] ? ieee80211_led_names+0xb8/0x100 [mac80211]
[ 7363.454156]  [<ffffffffa0056116>] rt2x00usb_probe+0x156/0x1f0 [rt2x00usb]
[ 7363.460971]  [<ffffffffa0074250>] rt2800usb_probe+0x10/0x20 [rt2800usb]
[ 7363.467616]  [<ffffffff8152799e>] usb_probe_interface+0xce/0x1c0
[ 7363.473651]  [<ffffffff81480c20>] really_probe+0x70/0x240
[ 7363.479079]  [<ffffffff81480f01>] __driver_attach+0xa1/0xb0
[ 7363.484682]  [<ffffffff81480e60>] ? __device_attach+0x70/0x70
[ 7363.490461]  [<ffffffff8147eef3>] bus_for_each_dev+0x63/0xa0
[ 7363.496146]  [<ffffffff814807c9>] driver_attach+0x19/0x20
[ 7363.501570]  [<ffffffff81480468>] bus_add_driver+0x178/0x220
[ 7363.507270]  [<ffffffff8148151b>] driver_register+0x5b/0xe0
[ 7363.512874]  [<ffffffff815271b0>] usb_register_driver+0xa0/0x170
[ 7363.518905]  [<ffffffffa007a000>] ? 0xffffffffa0079fff
[ 7363.524074]  [<ffffffffa007a01e>] rt2800usb_driver_init+0x1e/0x20 [rt2800usb]
[ 7363.531247]  [<ffffffff810002d4>] do_one_initcall+0x84/0x1b0
[ 7363.536932]  [<ffffffff8113aa60>] ? kfree+0xd0/0x110
[ 7363.541931]  [<ffffffff8112730a>] ? __vunmap+0xaa/0xf0
[ 7363.547538]  [<ffffffff810ca07e>] load_module+0x1aee/0x2040
[ 7363.553141]  [<ffffffff810c6f10>] ? store_uevent+0x50/0x50
[ 7363.558676]  [<ffffffff810ca66e>] SyS_init_module+0x9e/0xc0
[ 7363.564285]  [<ffffffff81764012>] system_call_fastpath+0x16/0x1b
[ 7363.570338] ---[ end trace 01ef5f822bea9882 ]---

Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10 years agoMerge branch 'for-john' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi...
John W. Linville [Mon, 7 Jul 2014 18:59:57 +0000 (14:59 -0400)]
Merge branch 'for-john' of git://git./linux/kernel/git/iwlwifi/iwlwifi-fixes

10 years agoiwlwifi: mvm: minor fix in comment
Emmanuel Grumbach [Thu, 5 Jun 2014 08:32:41 +0000 (11:32 +0300)]
iwlwifi: mvm: minor fix in comment

The comment was not accurate, we are talking about the frames
*for* the station and not from the station.

Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: remove 8000 HW family setting of adc sampling on nic config
Liad Kaufman [Thu, 8 May 2014 13:30:24 +0000 (16:30 +0300)]
iwlwifi: mvm: remove 8000 HW family setting of adc sampling on nic config

This patch removes the setting of the ADC sampling bits in
the mvm nic configuration. This setting is not required by
the firmware, and furthermore - it interferes with the DBGC
when it is running in DRAM mode on PCIe.

Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: teardown TDLS peers when initiating DCM
Arik Nemtsov [Tue, 10 Jun 2014 16:56:27 +0000 (19:56 +0300)]
iwlwifi: mvm: teardown TDLS peers when initiating DCM

The FW currently doesn't optimally support TDLS in DCM mode. Teardown
all TDLS peers when we have more than a single phy context.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: disable PSM on vifs with associated TDLS peers
Arik Nemtsov [Thu, 15 May 2014 15:59:32 +0000 (18:59 +0300)]
iwlwifi: disable PSM on vifs with associated TDLS peers

The FW does not support PSM on a vif with associated TDLS peers. Disable
PSM when the first peer joins and re-enable it when the last leaves.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: protect TDLS discovery session
Arik Nemtsov [Tue, 20 May 2014 15:16:42 +0000 (18:16 +0300)]
iwlwifi: mvm: protect TDLS discovery session

Use the new mac80211 callback to protect a TDLS discovery session so we
can hear the discovery-response packet.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: disallow new TDLS stations when appropriate
Arik Nemtsov [Thu, 15 May 2014 08:44:40 +0000 (11:44 +0300)]
iwlwifi: mvm: disallow new TDLS stations when appropriate

HW/FW constraints dictate that TDLS should only be used when a single
phy ctx is active. We also support at most 4 TDLS peers. We don't
support TDLS on a P2P vif.

Unify and move a phy-ctx counting implementation from the power-mgmt code
in order to simplify implementation.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: Use CS tx block bit for AP/GO
Andrei Otcheretianski [Sun, 25 May 2014 14:24:22 +0000 (17:24 +0300)]
iwlwifi: mvm: Use CS tx block bit for AP/GO

An AP/GO may perform the channel switch slightly before its stations.
This scenario may result in packet loss, since the transmission may start
before the client is actually on a new channel. In order to prevent
potential packet loss disable tx to all the stations when the channel
switch flow starts. Clear the disable_tx bit when a station is seen on a
target channel, or after IWL_MVM_CS_UNBLOCK_TX_TIMEOUT beacons on a new
channel. In addition call ieee80211_sta_block_awake in order to inform
mac80211 that the frames for this station should be buffered.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: Reflect GO channel switch in NoA
Andrei Otcheretianski [Sun, 4 May 2014 08:48:12 +0000 (11:48 +0300)]
iwlwifi: mvm: Reflect GO channel switch in NoA

According to the spec, GO/AP should perform the channel switch just
before "beacon 0". However, since the exact timing isn't defined,
it may result in a sudden GO disappearance from the channel.
Prevent potential packet loss when performing the CS by scheduling
NoA time event and executing the channel switch flow when a notification
from fw is received.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: Protect mvm->csa_vif with RCU
Andrei Otcheretianski [Thu, 5 Jun 2014 13:40:36 +0000 (16:40 +0300)]
iwlwifi: mvm: Protect mvm->csa_vif with RCU

Currently mvm->csa_vif is protected with mvm mutex. The RCU protection
is required for "iwlwifi: mvm: Reflect GO channel switch in NoA" patch.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: Use beacon_get_template instead of beacon_get
Andrei Otcheretianski [Thu, 10 Apr 2014 18:46:16 +0000 (21:46 +0300)]
iwlwifi: mvm: Use beacon_get_template instead of beacon_get

Call ieee80211_beacon_get_template instead of ieee80211_beacon_get and sync the
CSA counters with mac80211 after each beacon transmission.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: CSA unbind-bind flow support for client
Luciano Coelho [Wed, 5 Mar 2014 13:41:48 +0000 (15:41 +0200)]
iwlwifi: mvm: CSA unbind-bind flow support for client

Implement support for unbind-bind flow for the client roles.  This
includes telling the firmware that we are not associated, removing
time-events, removing quotas and updating power management during the
actual switch, and redoing everything in the new channel.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: add switch_vif_chanctx operation
Luciano Coelho [Tue, 20 May 2014 20:31:05 +0000 (23:31 +0300)]
iwlwifi: mvm: add switch_vif_chanctx operation

Implement the switch_vif_chanctx operation with support for a
single-vif and SWAP mode.  The REASSIGN mode and multi-vifs are not
supported yet.

This operation needs to implement 4 steps, namely unassign, remove,
add and assign the chanctx.  In order to do this, split out these
operations into locked and non-locked parts, thus allowing us to call
them while locked.

Additionally, in order to allow us to restart the hardware when
something fails, add a boolean to the iwl_mvm_nic_restart() function
that tells whether the restart was triggered by a FW error or
something else.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: remove update type argument from quota update
Johannes Berg [Fri, 6 Jun 2014 13:18:45 +0000 (15:18 +0200)]
iwlwifi: mvm: remove update type argument from quota update

It turns out that adding the update type argument was pointless as
quota update is never called from the add_interface() callback.
Therefore, IWL_MVM_QUOTA_UPDATE_TYPE_NEW isn't actually needed and
then only a "disabled_vif" argument is needed for the upcoming CSA
work.

Remove the whole enum iwl_mvm_quota_update_type and pass the right
arguments (always NULL for disabled vif right now) to the function
in all current call sites.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: don't pass update type to quota iterator
Johannes Berg [Fri, 23 May 2014 14:17:13 +0000 (16:17 +0200)]
iwlwifi: mvm: don't pass update type to quota iterator

Simplify the quota iterator by not passing the update type,
it only needs to know whether or not to skip an interface.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: validate that we don't send zero quota
Johannes Berg [Fri, 23 May 2014 14:13:57 +0000 (16:13 +0200)]
iwlwifi: mvm: validate that we don't send zero quota

The firmware currently deals with zero quota for a given
binding, but it seems odd to send that down. Make sure
that we don't do that.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: don't send zero quota to the firmware
Johannes Berg [Fri, 23 May 2014 14:15:11 +0000 (16:15 +0200)]
iwlwifi: mvm: don't send zero quota to the firmware

There are some cases where we can currently send zero quota
for a valid binding, e.g. if we update while an interface is
bound to a channel context but not yet acting as an AP.

Avoid this by reordering the checks.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: let iwl_mvm_update_quotas disregard a disabled vif
Luciano Coelho [Tue, 13 May 2014 19:28:35 +0000 (22:28 +0300)]
iwlwifi: mvm: let iwl_mvm_update_quotas disregard a disabled vif

In some cases (e.g. when we're doing a channel switch), we may need to
disable the quota of a vif temporarily.  In order to do so, add an
argument to the iwl_mvm_update_quotas() function to tell if the passed
vif is a new one or if it should be disregarded.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: 8000: drop a print when the address is invalid
Eran Harary [Sun, 29 Jun 2014 08:53:06 +0000 (11:53 +0300)]
iwlwifi: 8000: drop a print when the address is invalid

when driver takes the MAC address from the HW section and
it isn't valid - print an error.

Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: fix endianity in scan command
David Spinadel [Wed, 25 Jun 2014 10:17:53 +0000 (13:17 +0300)]
iwlwifi: mvm: fix endianity in scan command

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: init lmac scan command
David Spinadel [Thu, 12 Jun 2014 16:29:40 +0000 (19:29 +0300)]
iwlwifi: mvm: init lmac scan command

Initialize LMAC scan command.
Fix EBS flag to be dependant on TLV flg and fix other bugs.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: add unified LMAC scan API
David Spinadel [Sun, 4 May 2014 09:51:10 +0000 (12:51 +0300)]
iwlwifi: mvm: add unified LMAC scan API

Add new scan API that uses the same command 0x51 for both regular and
sched scan.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: rs: don't save debugfs files
Eliad Peller [Sun, 15 Jun 2014 09:02:20 +0000 (12:02 +0300)]
iwlwifi: mvm: rs: don't save debugfs files

These file are removed recursively anyway, so there's no
point saving them just to redundantly remove them later.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: rs: don't clear persistent fields
Eliad Peller [Wed, 11 Jun 2014 12:51:33 +0000 (15:51 +0300)]
iwlwifi: mvm: rs: don't clear persistent fields

iwl_mvm_rs_rate_init() is called multiple times to re-init
the rate scaling statistics (e.g. after some idle time).

It clears all the lq_sta sta, including some fields that
shouldn't be cleared (e.g. debugfs pointers). Fix it
by adding a new 'persistent' sub-struct, and
avoid clearing it on (re-)init.

Move the initialization of the persistent fields to
rs_alloc_sta instead.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: warn about empty OTP
Eran Harary [Tue, 1 Jul 2014 14:31:38 +0000 (17:31 +0300)]
iwlwifi: mvm: warn about empty OTP

Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: BT Coex - relax constraints when TTC / RRC is active
Emmanuel Grumbach [Mon, 30 Jun 2014 07:26:02 +0000 (10:26 +0300)]
iwlwifi: mvm: BT Coex - relax constraints when TTC / RRC is active

When TxTxCo-Running is active, we can relax the constraints
on the rate control.
When RxRxCo-Running is active, we can relax the constrains
on SMPS.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: BT Coex - fix debugfs with old API
Emmanuel Grumbach [Wed, 2 Jul 2014 14:33:52 +0000 (17:33 +0300)]
iwlwifi: mvm: BT Coex - fix debugfs with old API

Fix the debugfs hook to make it able to display the data
with the old firmware API.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: BT Coex - add High Band retention
Emmanuel Grumbach [Wed, 11 Jun 2014 12:37:25 +0000 (15:37 +0300)]
iwlwifi: mvm: BT Coex - add High Band retention

Tell the firmware if TTC should be enabled when switching
to High Band.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: BT Coex - convert reduced Tx power to new API
Emmanuel Grumbach [Thu, 22 May 2014 09:48:27 +0000 (12:48 +0300)]
iwlwifi: mvm: BT Coex - convert reduced Tx power to new API

No need to send the big BT_COEX_CMD command, we have now
a much thiner command that updates only what is needed.
Adapt the code to that.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: BT Coex - convert the co-running update to new API
Emmanuel Grumbach [Wed, 2 Apr 2014 09:23:09 +0000 (12:23 +0300)]
iwlwifi: mvm: BT Coex - convert the co-running update to new API

No need to send the big BT_COEX_CMD command, we have now
a much thiner command that updates only what is needed.
Adapt the code to that.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: BT Coex - convert the sw boost update to new API
Emmanuel Grumbach [Wed, 2 Apr 2014 09:23:09 +0000 (12:23 +0300)]
iwlwifi: mvm: BT Coex - convert the sw boost update to new API

No need to send the big BT_COEX_CMD command, we have now
a much thiner command that updates only what is needed.
Adapt the code to that, and open the patch to the updates.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: BT Coex - new API
Emmanuel Grumbach [Wed, 2 Apr 2014 06:55:16 +0000 (09:55 +0300)]
iwlwifi: mvm: BT Coex - new API

Start the new BT Coex implementation.
Don't react to notifications for now - only the initial
configuration is implemented. The rest will happen in next
patches.
Since coex.c now uses the new the new structures in all
functions, we need to adapt the code to compile, even if it
doesn't run yet.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoiwlwifi: mvm: BT Coex - prepare towards new API
Emmanuel Grumbach [Wed, 2 Apr 2014 06:31:36 +0000 (09:31 +0300)]
iwlwifi: mvm: BT Coex - prepare towards new API

A new API is coming. This new API is not backward
compatible. So we need to keep the old commands to be able
to work with the former API.
Move all the current code into a new file: coex_legacy.
If a firmware with the new API is detected, we currently
just bail out since the implementation of the new API will
come in future patches.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
10 years agoBluetooth: Don't try background scanning if LE is not enabled
Johan Hedberg [Mon, 7 Jul 2014 12:19:50 +0000 (15:19 +0300)]
Bluetooth: Don't try background scanning if LE is not enabled

For adapters that do not support LE and ones where LE hasn't been
enabled we shouldn't be trying to initiate background scanning. This
patch adds an extra check to the hci_update_background_scan() to ensure
that we bail out if HCI_LE_ENABLED is not set.

Since we do allow user space to feed the kernel with LE connection
parameters even when LE is not enabled we now need to also call
hci_update_background_scan() as soon as LE gets enabled so that scanning
gets started if necessary.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Pass desired connection role to hci_connect_le()
Johan Hedberg [Mon, 7 Jul 2014 12:02:28 +0000 (15:02 +0300)]
Bluetooth: Pass desired connection role to hci_connect_le()

If we have both LE scanning and advertising simultaneously enabled we
need a way to tell hci_connect_le() in which role to initiate a
connection. This patch adds a new parameter to the function to give it
the necessary information. For auto-connect and mgmt_pair_device we
always use master role, whereas for L2CAP users (in practice sockets) we
use slave role whenever HCI_ADVERTISING is set and master role
otherwise.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Remove auth_type parameter from hci_connect_le()
Johan Hedberg [Mon, 7 Jul 2014 12:02:27 +0000 (15:02 +0300)]
Bluetooth: Remove auth_type parameter from hci_connect_le()

The auth_type value which gets assigned to hci_conn->auth_type is
something that's only used for BR/EDR connections and is of no value for
LE connections. It makes therefore little sense to pass it to the
hci_connect_le() function. This patch removes the parameter from the
function.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Enable passive scanning whenever we're connectable
Johan Hedberg [Mon, 7 Jul 2014 11:40:22 +0000 (14:40 +0300)]
Bluetooth: Enable passive scanning whenever we're connectable

Enabling passive scanning always when we're connectable aligns us with
the BR/EDR page scanning. This is also consistent with the fact that the
code dealing with passive scanning results will actively try to connect
any direct advertising event when we're connectable.

This patch implements the feature by adding the connectable condition to
hci_update_background_scan() checks for starting scanning and by calling
hci_update_background_scan() whenever the connectable state changes.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Don't let background scanning interfering with discovery
Johan Hedberg [Mon, 7 Jul 2014 10:24:59 +0000 (13:24 +0300)]
Bluetooth: Don't let background scanning interfering with discovery

If we have an active discovery going on we shouldn't do any changes to
LE scanning when hci_update_background_scan() is called (a call which
can happen for many different reasons). This patch fixes the issue by
returning from the function if the discovery state is anything else
except DISCOVERY_STOPPED.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Update discovery state earlier in hci_discovery_set_state
Johan Hedberg [Mon, 7 Jul 2014 10:24:58 +0000 (13:24 +0300)]
Bluetooth: Update discovery state earlier in hci_discovery_set_state

In a subsequent patch the hci_update_background_scan() function will
depend on being able to know the current discovery state. For this to be
possible we need to set the new state early in the function. Since we
also need to check what the old state was this patch introduces an extra
variable for tracking it.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Remove unnecessary return value from check_pending_le_conn
Johan Hedberg [Mon, 7 Jul 2014 09:45:55 +0000 (12:45 +0300)]
Bluetooth: Remove unnecessary return value from check_pending_le_conn

Since the only caller of this function doesn't care about the return
value anymore let's just remove it.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Remove redundant IRK lookup in mgmt_device_found()
Johan Hedberg [Mon, 7 Jul 2014 09:45:54 +0000 (12:45 +0300)]
Bluetooth: Remove redundant IRK lookup in mgmt_device_found()

Now that we have the process_adv_report() function doing the IRK lookup
and updating the bdaddr we don't need to do this anymore in mgmt.c in
the mgmt_device_found() function.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix connecting devices during LE device discovery
Johan Hedberg [Mon, 7 Jul 2014 09:45:53 +0000 (12:45 +0300)]
Bluetooth: Fix connecting devices during LE device discovery

If we have devices set as to be connected we should connect to them even
during normal discovery if we get a connectable advertising event. If we
also have HCI_CONNECTABLE set we should connect ADV_DIRECT_IND events
even to devices that we don't have in our pend_le_conns list. This patch
implements such behavior by passing the advertising report type to
check_pending_le_conn() and calls that function regardless of what type
of scanning we are doing.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Use BTUSB_BROKEN_ISOC flag for CSR USB sniffer devices
Marcel Holtmann [Sun, 6 Jul 2014 22:12:04 +0000 (00:12 +0200)]
Bluetooth: Use BTUSB_BROKEN_ISOC flag for CSR USB sniffer devices

Instead of setting data->isoc manually, use BTUSB_BROKEN_ISOC to
indicate that isochronous endpoints are not needed for CSR USB
sniffer devices.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Enforce providing hdev->send driver callback
Marcel Holtmann [Sun, 6 Jul 2014 13:50:27 +0000 (15:50 +0200)]
Bluetooth: Enforce providing hdev->send driver callback

The hdev->send driver callback is mandatory to be provided by a driver
before calling hci_register_dev. So enforce it and return EINVAL in
case it is not available.

All existing drivers are providing this callback anyway, so this is
just an extra sanity check.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Fix memory leaking when hdev->send returns an error
Marcel Holtmann [Sun, 6 Jul 2014 13:36:15 +0000 (15:36 +0200)]
Bluetooth: Fix memory leaking when hdev->send returns an error

The drivers are allowed to just return an error from hdev->send callback
and in that case the driver does not own the SKB. Which means that the
caller has to free the SKB.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Ignore isochronous endpoints for Intel USB bootloader
Marcel Holtmann [Sun, 6 Jul 2014 12:53:55 +0000 (14:53 +0200)]
Bluetooth: Ignore isochronous endpoints for Intel USB bootloader

The isochronous endpoints are not valid when the Intel Bluetooth
controller boots up in bootloader mode. So just mark these endpoints
as broken and then they will not be configured.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>