GitHub/exynos8895/android_kernel_samsung_universal8895.git
12 years agonet: ucc_geth, increase no. of HW RX descriptors
Joakim Tjernlund [Sun, 29 Apr 2012 22:36:54 +0000 (22:36 +0000)]
net: ucc_geth, increase no. of HW RX descriptors

In a busy network we see ucc_geth is dropping RX pkgs every now
and then. Increase the RX queues HW descriptors from
16 to 32 to deal with this.

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
John W. Linville [Tue, 1 May 2012 18:14:05 +0000 (14:14 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless into for-davem

12 years agonetem: fix possible skb leak
Eric Dumazet [Sun, 29 Apr 2012 09:08:22 +0000 (09:08 +0000)]
netem: fix possible skb leak

skb_checksum_help(skb) can return an error, we must free skb in this
case. qdisc_drop(skb, sch) can also be feeded with a NULL skb (if
skb_unshare() failed), so lets use this generic helper.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agosky2: fix receive length error in mixed non-VLAN/VLAN traffic
stephen hemminger [Mon, 30 Apr 2012 06:47:37 +0000 (06:47 +0000)]
sky2: fix receive length error in mixed non-VLAN/VLAN traffic

Bug: The VLAN bit of the MAC RX Status Word is unreliable in several older
supported chips. Sometimes the VLAN bit is not set for valid VLAN packets
and also sometimes the VLAN bit is set for non-VLAN packets that came after
a VLAN packet. This results in a receive length error when VLAN hardware
tagging is enabled.

Fix: Variation on original fix proposed by Mirko.
The VLAN information is decoded in the status loop, and can be
applied to the received SKB there. This eliminates the need for the
separate tag field in the interface data structure. The tag has to
be copied and cleared if packet is copied. This version checked out
with vlan and normal traffic.

Note: vlan_tx_tag_present should be renamed vlan_tag_present, but that
is outside scope of this.

Reported-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agosky2: propogate rx hash when packet is copied
stephen hemminger [Mon, 30 Apr 2012 05:49:45 +0000 (05:49 +0000)]
sky2: propogate rx hash when packet is copied

When a small packet is received, the driver copies it to a new skb to allow
reusing the full size Rx buffer. The copy was propogating the checksum offload
but not the receive hash information. The bug is impact was mostly harmless
and therefore not observed until reviewing this area of code.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agonet: fix two typos in skbuff.h
Eric Dumazet [Mon, 30 Apr 2012 21:29:16 +0000 (21:29 +0000)]
net: fix two typos in skbuff.h

fix kernel doc typos in function names

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agocxgb3: Don't call cxgb_vlan_mode until q locks are initialized
Roland Dreier [Mon, 30 Apr 2012 07:15:47 +0000 (07:15 +0000)]
cxgb3: Don't call cxgb_vlan_mode until q locks are initialized

The driver calls cxgb_vlan_mode() from init_one().  This calls into
synchronize_rx(), which locks all the q locks, but the q locks are not
initialized until cxgb_up() -> setup_sge_qsets().  So move the call to
cxgb_vlan_mode() into cxgb_up(), after the call to setup_sge_qsets().
We also move the body of these functions up higher to avoid having to
a forward declaration.

This was found because of the lockdep warning:

    INFO: trying to register non-static key.
    the code is fine but needs lockdep annotation.
    turning off the locking correctness validator.
    Pid: 323, comm: work_for_cpu Not tainted 3.4.0-rc5 #28
    Call Trace:
     [<ffffffff8106e767>] register_lock_class+0x108/0x2d0
     [<ffffffff8106ff42>] __lock_acquire+0xd3/0xd06
     [<ffffffff81070fd0>] lock_acquire+0xbf/0xfe
     [<ffffffff813862a6>] _raw_spin_lock_irq+0x36/0x45
     [<ffffffffa01e71aa>] cxgb_vlan_mode+0x96/0xcb [cxgb3]
     [<ffffffffa01f90eb>] init_one+0x8c4/0x980 [cxgb3]
     [<ffffffff811fcbf0>] local_pci_probe+0x3f/0x70
     [<ffffffff81042206>] do_work_for_cpu+0x10/0x22
     [<ffffffff810482de>] kthread+0xa1/0xa9
     [<ffffffff8138e234>] kernel_thread_helper+0x4/0x10

Contrary to what lockdep says, the code is not fine: we are locking an
uninitialized spinlock.

Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net
David S. Miller [Tue, 1 May 2012 02:04:20 +0000 (22:04 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/jkirsher/net

12 years agoixgbe: fix calling skb_put on nonlinear skb assertion bug
Yi Zou [Fri, 20 Apr 2012 05:48:08 +0000 (05:48 +0000)]
ixgbe: fix calling skb_put on nonlinear skb assertion bug

With the support to bounce buffer added, the skb is coming as nonlinear in the
case of non-DDPed data frames for FCoE, which is mostly ok as the FCoE stack
would take care of that. However, for target mode, we have to set the FC CRC
and FC EOF field to allow the protocol stack to not drop the frame for the last
data frame of that sequence. So fix this by linearizing the skb first before
doing skb_put().

Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
12 years agoixgbe: Fix a memory leak in IEEE DCB
Alexander Duyck [Sat, 17 Mar 2012 02:39:16 +0000 (02:39 +0000)]
ixgbe: Fix a memory leak in IEEE DCB

The driver was freeing memory in shutdown instead of remove.  As a result
we were leaking memory if IEEE DCB was enabled and we loaded/unloaded the
driver.  This change moves the freeing of the memory into the remove
routine where it belongs.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
12 years agoigbvf: fix the bug when initializing the igbvf
Samuel Liao [Fri, 27 Apr 2012 17:09:27 +0000 (17:09 +0000)]
igbvf: fix the bug when initializing the igbvf

Maybe it's a typo, but it cause that igbvf can't be initialized successfully.
Set perm_addr value using valid dev_addr, although which is equal to hw.mac.addr.

Signed-off-by: Samuel Liao <samuelliao@tencent.com>
Signed-off-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
12 years agosmsc75xx: enable mac to detect speed/duplex from phy
Steve Glendinning [Mon, 30 Apr 2012 07:56:56 +0000 (07:56 +0000)]
smsc75xx: enable mac to detect speed/duplex from phy

This patch sets the automatic speed and duplex detection bits
in MAC_CR to enable the mac to determine its speed automatically
from the phy.

Note this must be done BEFORE the receiver or transmitter is
enabled.

Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agosmsc75xx: declare smsc75xx's MII as GMII capable
Steve Glendinning [Mon, 30 Apr 2012 07:56:55 +0000 (07:56 +0000)]
smsc75xx: declare smsc75xx's MII as GMII capable

also explicitly set the phy to advertise 1000 speeds

Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agosmsc75xx: fix phy interrupt acknowledge
Steve Glendinning [Mon, 30 Apr 2012 07:56:54 +0000 (07:56 +0000)]
smsc75xx: fix phy interrupt acknowledge

smsc75xx phy interrupt acknowledge needs an mdio_write to clear
PHY_INT_SRC instead of just a read like in smsc95xx.

Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agosmsc75xx: fix phy init reset loop
Steve Glendinning [Mon, 30 Apr 2012 07:56:53 +0000 (07:56 +0000)]
smsc75xx: fix phy init reset loop

fix bug in phy_init loop that was ignoring BMCR reset bit, akin to smsc95xx's d946092000698fd204d82a9d239103c656fb63bf

Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agosmsc75xx: add more information to register io failure warnings
Steve Glendinning [Mon, 30 Apr 2012 07:56:52 +0000 (07:56 +0000)]
smsc75xx: add more information to register io failure warnings

Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agosmsc75xx: fix mdio reads and writes
Steve Glendinning [Mon, 30 Apr 2012 07:56:51 +0000 (07:56 +0000)]
smsc75xx: fix mdio reads and writes

smsc75xx needs MII_ACCESS_BUSY to be set to correctly trigger mdio I/O.  Note smsc75xx is different from smsc95xx in this regard.

Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agosmsc75xx: mark link down on startup and let PHY interrupt deal with carrier changes
Steve Glendinning [Mon, 30 Apr 2012 07:56:50 +0000 (07:56 +0000)]
smsc75xx: mark link down on startup and let PHY interrupt deal with carrier changes

This patch fixes the same issue as reported on smsc95xx, where the
usb device is connected with no ethernet cable plugged-in.

Without this patch sysfs reports the cable as present

flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier
1

while it's not:

flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link

Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agomac80211: fix AP mode EAP tx for VLAN stations
Felix Fietkau [Sun, 29 Apr 2012 13:44:16 +0000 (15:44 +0200)]
mac80211: fix AP mode EAP tx for VLAN stations

EAP frames for stations in an AP VLAN are sent on the main AP interface
to avoid race conditions wrt. moving stations.
For that to work properly, sta_info_get_bss must be used instead of
sta_info_get when sending EAP packets.
Previously this was only done for cooked monitor injected packets, so
this patch adds a check for tx->skb->protocol to the same place.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agotcp: fix infinite cwnd in tcp_complete_cwr()
Yuchung Cheng [Mon, 30 Apr 2012 06:00:18 +0000 (06:00 +0000)]
tcp: fix infinite cwnd in tcp_complete_cwr()

When the cwnd reduction is done, ssthresh may be infinite
if TCP enters CWR via ECN or F-RTO. If cwnd is not undone, i.e.,
undo_marker is set, tcp_complete_cwr() falsely set cwnd to the
infinite ssthresh value. The correct operation is to keep cwnd
intact because it has been updated in ECN or F-RTO.

Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agobpf jit: Let the powerpc jit handle negative offsets
Jan Seiffert [Sun, 29 Apr 2012 19:02:19 +0000 (19:02 +0000)]
bpf jit: Let the powerpc jit handle negative offsets

Now the helper function from filter.c for negative offsets is exported,
it can be used it in the jit to handle negative offsets.

First modify the asm load helper functions to handle:
- know positive offsets
- know negative offsets
- any offset

then the compiler can be modified to explicitly use these helper
when appropriate.

This fixes the case of a negative X register and allows to lift
the restriction that bpf programs with negative offsets can't
be jited.

Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jan Seiffert <kaffeemonster@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agonet: fix sk_sockets_allocated_read_positive
Eric Dumazet [Sat, 28 Apr 2012 23:21:56 +0000 (23:21 +0000)]
net: fix sk_sockets_allocated_read_positive

Denys Fedoryshchenko reported frequent crashes on a proxy server and kindly
provided a lockdep report that explains it all :

  [  762.903868]
  [  762.903880] =================================
  [  762.903890] [ INFO: inconsistent lock state ]
  [  762.903903] 3.3.4-build-0061 #8 Not tainted
  [  762.904133] ---------------------------------
  [  762.904344] inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
  [  762.904542] squid/1603 [HC0[0]:SC0[0]:HE1:SE1] takes:
  [  762.904542]  (key#3){+.?...}, at: [<c0232cc4>]
__percpu_counter_sum+0xd/0x58
  [  762.904542] {IN-SOFTIRQ-W} state was registered at:
  [  762.904542]   [<c0158b84>] __lock_acquire+0x284/0xc26
  [  762.904542]   [<c01598e8>] lock_acquire+0x71/0x85
  [  762.904542]   [<c0349765>] _raw_spin_lock+0x33/0x40
  [  762.904542]   [<c0232c93>] __percpu_counter_add+0x58/0x7c
  [  762.904542]   [<c02cfde1>] sk_clone_lock+0x1e5/0x200
  [  762.904542]   [<c0303ee4>] inet_csk_clone_lock+0xe/0x78
  [  762.904542]   [<c0315778>] tcp_create_openreq_child+0x1b/0x404
  [  762.904542]   [<c031339c>] tcp_v4_syn_recv_sock+0x32/0x1c1
  [  762.904542]   [<c031615a>] tcp_check_req+0x1fd/0x2d7
  [  762.904542]   [<c0313f77>] tcp_v4_do_rcv+0xab/0x194
  [  762.904542]   [<c03153bb>] tcp_v4_rcv+0x3b3/0x5cc
  [  762.904542]   [<c02fc0c4>] ip_local_deliver_finish+0x13a/0x1e9
  [  762.904542]   [<c02fc539>] NF_HOOK.clone.11+0x46/0x4d
  [  762.904542]   [<c02fc652>] ip_local_deliver+0x41/0x45
  [  762.904542]   [<c02fc4d1>] ip_rcv_finish+0x31a/0x33c
  [  762.904542]   [<c02fc539>] NF_HOOK.clone.11+0x46/0x4d
  [  762.904542]   [<c02fc857>] ip_rcv+0x201/0x23e
  [  762.904542]   [<c02daa3a>] __netif_receive_skb+0x319/0x368
  [  762.904542]   [<c02dac07>] netif_receive_skb+0x4e/0x7d
  [  762.904542]   [<c02dacf6>] napi_skb_finish+0x1e/0x34
  [  762.904542]   [<c02db122>] napi_gro_receive+0x20/0x24
  [  762.904542]   [<f85d1743>] e1000_receive_skb+0x3f/0x45 [e1000e]
  [  762.904542]   [<f85d3464>] e1000_clean_rx_irq+0x1f9/0x284 [e1000e]
  [  762.904542]   [<f85d3926>] e1000_clean+0x62/0x1f4 [e1000e]
  [  762.904542]   [<c02db228>] net_rx_action+0x90/0x160
  [  762.904542]   [<c012a445>] __do_softirq+0x7b/0x118
  [  762.904542] irq event stamp: 156915469
  [  762.904542] hardirqs last  enabled at (156915469): [<c019b4f4>]
__slab_alloc.clone.58.clone.63+0xc4/0x2de
  [  762.904542] hardirqs last disabled at (156915468): [<c019b452>]
__slab_alloc.clone.58.clone.63+0x22/0x2de
  [  762.904542] softirqs last  enabled at (156915466): [<c02ce677>]
lock_sock_nested+0x64/0x6c
  [  762.904542] softirqs last disabled at (156915464): [<c0349914>]
_raw_spin_lock_bh+0xe/0x45
  [  762.904542]
  [  762.904542] other info that might help us debug this:
  [  762.904542]  Possible unsafe locking scenario:
  [  762.904542]
  [  762.904542]        CPU0
  [  762.904542]        ----
  [  762.904542]   lock(key#3);
  [  762.904542]   <Interrupt>
  [  762.904542]     lock(key#3);
  [  762.904542]
  [  762.904542]  *** DEADLOCK ***
  [  762.904542]
  [  762.904542] 1 lock held by squid/1603:
  [  762.904542]  #0:  (sk_lock-AF_INET){+.+.+.}, at: [<c03055c0>]
lock_sock+0xa/0xc
  [  762.904542]
  [  762.904542] stack backtrace:
  [  762.904542] Pid: 1603, comm: squid Not tainted 3.3.4-build-0061 #8
  [  762.904542] Call Trace:
  [  762.904542]  [<c0347b73>] ? printk+0x18/0x1d
  [  762.904542]  [<c015873a>] valid_state+0x1f6/0x201
  [  762.904542]  [<c0158816>] mark_lock+0xd1/0x1bb
  [  762.904542]  [<c015876b>] ? mark_lock+0x26/0x1bb
  [  762.904542]  [<c015805d>] ? check_usage_forwards+0x77/0x77
  [  762.904542]  [<c0158bf8>] __lock_acquire+0x2f8/0xc26
  [  762.904542]  [<c0159b8e>] ? mark_held_locks+0x5d/0x7b
  [  762.904542]  [<c0159cf6>] ? trace_hardirqs_on+0xb/0xd
  [  762.904542]  [<c0158dd4>] ? __lock_acquire+0x4d4/0xc26
  [  762.904542]  [<c01598e8>] lock_acquire+0x71/0x85
  [  762.904542]  [<c0232cc4>] ? __percpu_counter_sum+0xd/0x58
  [  762.904542]  [<c0349765>] _raw_spin_lock+0x33/0x40
  [  762.904542]  [<c0232cc4>] ? __percpu_counter_sum+0xd/0x58
  [  762.904542]  [<c0232cc4>] __percpu_counter_sum+0xd/0x58
  [  762.904542]  [<c02cebc4>] __sk_mem_schedule+0xdd/0x1c7
  [  762.904542]  [<c02d178d>] ? __alloc_skb+0x76/0x100
  [  762.904542]  [<c0305e8e>] sk_wmem_schedule+0x21/0x2d
  [  762.904542]  [<c0306370>] sk_stream_alloc_skb+0x42/0xaa
  [  762.904542]  [<c0306567>] tcp_sendmsg+0x18f/0x68b
  [  762.904542]  [<c031f3dc>] ? ip_fast_csum+0x30/0x30
  [  762.904542]  [<c0320193>] inet_sendmsg+0x53/0x5a
  [  762.904542]  [<c02cb633>] sock_aio_write+0xd2/0xda
  [  762.904542]  [<c015876b>] ? mark_lock+0x26/0x1bb
  [  762.904542]  [<c01a1017>] do_sync_write+0x9f/0xd9
  [  762.904542]  [<c01a2111>] ? file_free_rcu+0x2f/0x2f
  [  762.904542]  [<c01a17a1>] vfs_write+0x8f/0xab
  [  762.904542]  [<c01a284d>] ? fget_light+0x75/0x7c
  [  762.904542]  [<c01a1900>] sys_write+0x3d/0x5e
  [  762.904542]  [<c0349ec9>] syscall_call+0x7/0xb
  [  762.904542]  [<c0340000>] ? rp_sidt+0x41/0x83

Bug is that sk_sockets_allocated_read_positive() calls
percpu_counter_sum_positive() without BH being disabled.

This bug was added in commit 180d8cd942ce33
(foundations of per-cgroup memory pressure controlling.), since previous
code was using percpu_counter_read_positive() which is IRQ safe.

In __sk_mem_schedule() we dont need the precise count of allocated
sockets and can revert to previous behavior.

Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Sined-off-by: Eric Dumazet <edumazet@google.com>
Cc: Glauber Costa <glommer@parallels.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoMerge branch 'master' of git://1984.lsi.us.es/net
David S. Miller [Mon, 30 Apr 2012 17:23:22 +0000 (13:23 -0400)]
Merge branch 'master' of git://1984.lsi.us.es/net

12 years agonetfilter: xt_CT: fix wrong checking in the timeout assignment path
Pablo Neira Ayuso [Fri, 27 Apr 2012 00:00:50 +0000 (02:00 +0200)]
netfilter: xt_CT: fix wrong checking in the timeout assignment path

The current checking always succeeded. We have to check the first
character of the string to check that it's empty, thus, skipping
the timeout path.

This fixes the use of the CT target without the timeout option.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
12 years agoipvs: kernel oops - do_ip_vs_get_ctl
Hans Schillstrom [Thu, 26 Apr 2012 05:47:44 +0000 (07:47 +0200)]
ipvs: kernel oops - do_ip_vs_get_ctl

Change order of init so netns init is ready
when register ioctl and netlink.

Ver2
Whitespace fixes and __init added.

Reported-by: "Ryan O'Hara" <rohara@redhat.com>
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
12 years agoipvs: take care of return value from protocol init_netns
Hans Schillstrom [Thu, 26 Apr 2012 07:45:35 +0000 (09:45 +0200)]
ipvs: take care of return value from protocol init_netns

ip_vs_create_timeout_table() can return NULL
All functions protocol init_netns is affected of this patch.

Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
12 years agoipvs: null check of net->ipvs in lblc(r) shedulers
Hans Schillstrom [Thu, 26 Apr 2012 07:45:34 +0000 (09:45 +0200)]
ipvs: null check of net->ipvs in lblc(r) shedulers

Avoid crash when registering shedulers after
the IPVS core initialization for netns fails. Do this by
checking for present core (net->ipvs).

Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
12 years agodrop_monitor: Make updating data->skb smp safe
Neil Horman [Fri, 27 Apr 2012 10:11:49 +0000 (10:11 +0000)]
drop_monitor: Make updating data->skb smp safe

Eric Dumazet pointed out to me that the drop_monitor protocol has some holes in
its smp protections.  Specifically, its possible to replace data->skb while its
being written.  This patch corrects that by making data->skb an rcu protected
variable.  That will prevent it from being overwritten while a tracepoint is
modifying it.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agodrop_monitor: fix sleeping in invalid context warning
Neil Horman [Fri, 27 Apr 2012 10:11:48 +0000 (10:11 +0000)]
drop_monitor: fix sleeping in invalid context warning

Eric Dumazet pointed out this warning in the drop_monitor protocol to me:

[   38.352571] BUG: sleeping function called from invalid context at kernel/mutex.c:85
[   38.352576] in_atomic(): 1, irqs_disabled(): 0, pid: 4415, name: dropwatch
[   38.352580] Pid: 4415, comm: dropwatch Not tainted 3.4.0-rc2+ #71
[   38.352582] Call Trace:
[   38.352592]  [<ffffffff8153aaf0>] ? trace_napi_poll_hit+0xd0/0xd0
[   38.352599]  [<ffffffff81063f2a>] __might_sleep+0xca/0xf0
[   38.352606]  [<ffffffff81655b16>] mutex_lock+0x26/0x50
[   38.352610]  [<ffffffff8153aaf0>] ? trace_napi_poll_hit+0xd0/0xd0
[   38.352616]  [<ffffffff810b72d9>] tracepoint_probe_register+0x29/0x90
[   38.352621]  [<ffffffff8153a585>] set_all_monitor_traces+0x105/0x170
[   38.352625]  [<ffffffff8153a8ca>] net_dm_cmd_trace+0x2a/0x40
[   38.352630]  [<ffffffff8154a81a>] genl_rcv_msg+0x21a/0x2b0
[   38.352636]  [<ffffffff810f8029>] ? zone_statistics+0x99/0xc0
[   38.352640]  [<ffffffff8154a600>] ? genl_rcv+0x30/0x30
[   38.352645]  [<ffffffff8154a059>] netlink_rcv_skb+0xa9/0xd0
[   38.352649]  [<ffffffff8154a5f0>] genl_rcv+0x20/0x30
[   38.352653]  [<ffffffff81549a7e>] netlink_unicast+0x1ae/0x1f0
[   38.352658]  [<ffffffff81549d76>] netlink_sendmsg+0x2b6/0x310
[   38.352663]  [<ffffffff8150824f>] sock_sendmsg+0x10f/0x130
[   38.352668]  [<ffffffff8150abe0>] ? move_addr_to_kernel+0x60/0xb0
[   38.352673]  [<ffffffff81515f04>] ? verify_iovec+0x64/0xe0
[   38.352677]  [<ffffffff81509c46>] __sys_sendmsg+0x386/0x390
[   38.352682]  [<ffffffff810ffaf9>] ? handle_mm_fault+0x139/0x210
[   38.352687]  [<ffffffff8165b5bc>] ? do_page_fault+0x1ec/0x4f0
[   38.352693]  [<ffffffff8106ba4d>] ? set_next_entity+0x9d/0xb0
[   38.352699]  [<ffffffff81310b49>] ? tty_ldisc_deref+0x9/0x10
[   38.352703]  [<ffffffff8106d363>] ? pick_next_task_fair+0x63/0x140
[   38.352708]  [<ffffffff8150b8d4>] sys_sendmsg+0x44/0x80
[   38.352713]  [<ffffffff8165f8e2>] system_call_fastpath+0x16/0x1b

It stems from holding a spinlock (trace_state_lock) while attempting to register
or unregister tracepoint hooks, making in_atomic() true in this context, leading
to the warning when the tracepoint calls might_sleep() while its taking a mutex.
Since we only use the trace_state_lock to prevent trace protocol state races, as
well as hardware stat list updates on an rcu write side, we can just convert the
spinlock to a mutex to avoid this problem.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agowl1251: fix crash on remove due to leftover work item
Grazvydas Ignotas [Thu, 26 Apr 2012 20:07:44 +0000 (23:07 +0300)]
wl1251: fix crash on remove due to leftover work item

This driver currently leaves elp_work behind when stopping, which
occasionally results in data corruption because work function ends
up accessing freed memory, typical symptoms of this are various
worker_thread crashes. Fix it by cancelling elp_work.

Cc: stable@vger.kernel.org # v2.6.37+
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agowl1251: fix crash on remove due to premature kfree
Grazvydas Ignotas [Thu, 26 Apr 2012 20:07:43 +0000 (23:07 +0300)]
wl1251: fix crash on remove due to premature kfree

Currently SDIO glue frees it's own structure before calling
wl1251_free_hw(), which in turn calls ieee80211_unregister_hw().
The later call may result in a need to communicate with the chip
to stop it (as it happens now if the interface is still up before
rmmod), which means calls are made back to the glue, resulting in
freed memory access.

Fix this by freeing glue data last.

Cc: stable@vger.kernel.org # v2.6.37+
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agob43: only reload config after successful initialization
Seth Forshee [Wed, 25 Apr 2012 22:28:00 +0000 (17:28 -0500)]
b43: only reload config after successful initialization

Commit 2a19032 (b43: reload phy and bss settings after core restarts)
introduced an unconditional call to b43_op_config() at the end of
b43_op_start(). When firmware fails to load this can wedge the system.
There's no need to reload the configuration after a failed
initialization anyway, so only make the call if initialization was
successful.

BugLink: http://bugs.launchpad.net/bugs/950295
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoiwlwifi: use 6000G2B for 6030 device series
Wey-Yi Guy [Wed, 25 Apr 2012 15:10:08 +0000 (08:10 -0700)]
iwlwifi: use 6000G2B for 6030 device series

"iwlwifi: use correct released ucode version" change
the ucode api ok from 6000G2 to 6000G2B, but it shall belong
to 6030 device series, not the 6005 device series. Fix it

Cc: stable@vger.kernel.org #3.3+
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoath5k: add missing iounmap to AHB probe removal
Jonathan Bither [Tue, 24 Apr 2012 09:20:15 +0000 (05:20 -0400)]
ath5k: add missing iounmap to AHB probe removal

When our driver device is removed on the AHB bus, our IO memory is never unmapped.

Signed-off-by: Jonathan Bither <jonbither@gmail.com>
Reviewed-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agobrcm80211: fmac: fix missing completion events issue
Franky Lin [Mon, 23 Apr 2012 21:24:53 +0000 (14:24 -0700)]
brcm80211: fmac: fix missing completion events issue

dpc takes care of all data packets transmissions for sdio function
2. It is possible that it misses some completion events when the
traffic is heavy or it's running on a slow cpu. A linked list is
introduced to make sure dpc is invoked whenever needed.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agobrcm80211: fmac: fix SDIO function 0 register r/w issue
Franky Lin [Mon, 23 Apr 2012 21:24:52 +0000 (14:24 -0700)]
brcm80211: fmac: fix SDIO function 0 register r/w issue

SDIO stack doesn't have a structure for function 0. The structure
pointer stored in card->sdio_func[0] is actually for function 1.
With current implementation the register read/write is applied to
function 1. This pathch fixes the issue.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Florian Fainelli <florian@openwrt.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoMerge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetoot...
John W. Linville [Fri, 27 Apr 2012 19:16:43 +0000 (15:16 -0400)]
Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth

12 years agotcp: clean up use of jiffies in tcp_rcv_rtt_measure()
Neal Cardwell [Fri, 27 Apr 2012 15:29:37 +0000 (11:29 -0400)]
tcp: clean up use of jiffies in tcp_rcv_rtt_measure()

Clean up a reference to jiffies in tcp_rcv_rtt_measure() that should
instead reference tcp_time_stamp. Since the result of the subtraction
is passed into a function taking u32, this should not change any
behavior (and indeed the generated assembly does not change on
x86_64). However, it seems worth cleaning this up for consistency and
clarity (and perhaps to avoid bugs if this is copied and pasted
somewhere else).

Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoMAINTAINERS: update sctp maintainer address
Vlad Yasevich [Thu, 26 Apr 2012 10:27:18 +0000 (10:27 +0000)]
MAINTAINERS: update sctp maintainer address

Update my email address.

Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agosmsc95xx: mark link down on startup and let PHY interrupt deal with carrier changes
Paolo Pisati [Mon, 23 Apr 2012 04:05:20 +0000 (04:05 +0000)]
smsc95xx: mark link down on startup and let PHY interrupt deal with carrier changes

Without this patch sysfs reports the cable as present

flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier
1

while it's not:

flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link

Tested on my Beagle XM.

v2: added mantainer to the list of recipient

Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agodl2k: Clean up rio_ioctl
Jeff Mahoney [Wed, 25 Apr 2012 14:32:09 +0000 (14:32 +0000)]
dl2k: Clean up rio_ioctl

The dl2k driver's rio_ioctl call has a few issues:
- No permissions checking
- Implements SIOCGMIIREG and SIOCGMIIREG using the SIOCDEVPRIVATE numbers
- Has a few ioctls that may have been used for debugging at one point
  but have no place in the kernel proper.

This patch removes all but the MII ioctls, renumbers them to use the
standard ones, and adds the proper permission check for SIOCSMIIREG.

We can also get rid of the dl2k-specific struct mii_data in favor of
the generic struct mii_ioctl_data.

Since we have the phyid on hand, we can add the SIOCGMIIPHY ioctl too.

Most of the MII code for the driver could probably be converted to use
the generic MII library but I don't have a device to test the results.

Reported-by: Stephan Mueller <stephan.mueller@atsec.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years ago6lowpan: add missing spin_lock_init()
alex.bluesman.smirnov@gmail.com [Wed, 25 Apr 2012 23:24:58 +0000 (23:24 +0000)]
6lowpan: add missing spin_lock_init()

Add missing spin_lock_init() for frames list lock.

Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years ago6lowpan: clean up fragments list if module unloaded
alex.bluesman.smirnov@gmail.com [Wed, 25 Apr 2012 23:24:57 +0000 (23:24 +0000)]
6lowpan: clean up fragments list if module unloaded

Clean all the pending fragments and relative timers if 6lowpan link
is going to be deleted.

Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years ago6lowpan: fix segmentation fault caused by mlme request
alex.bluesman.smirnov@gmail.com [Wed, 25 Apr 2012 23:24:56 +0000 (23:24 +0000)]
6lowpan: fix segmentation fault caused by mlme request

Add nescesary mlme callbacks to satisfy "iz list" request from user space.
Due to 6lowpan device doesn't have its own phy, mlme implemented as a pipe
to a real phy to which 6lowpan is attached.

Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net
David S. Miller [Thu, 26 Apr 2012 09:08:45 +0000 (05:08 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/jkirsher/net

12 years agoehea: fix promiscuous mode
Thadeu Lima de Souza Cascardo [Wed, 25 Apr 2012 07:32:12 +0000 (07:32 +0000)]
ehea: fix promiscuous mode

commit a4910b744486254cfa61995954c118fb2283c4fd has broken promiscuous
mode, which is never set. port->promisc just reflects the last setting
of PROMISCUOUS mode to avoid doing an extra hypercall when it's already
set.

However, since it may fail because of hypervisor permissions, we should
still respect the multicast settings and not simply exit after setting
promiscuous mode.

Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Cc: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoehea: fix allmulticast support
Thadeu Lima de Souza Cascardo [Wed, 25 Apr 2012 07:32:11 +0000 (07:32 +0000)]
ehea: fix allmulticast support

There was a bug in the mask of regtype parameter for registering a
multicast filter. It was ignoring the scope bit, which was wrongly being
used for all filters. The SCOPE_ALL value adds a filter that allows all
multicast packets and ignores the MAC parameter, just what allmulticast
needs. The normals filters, however, should not use SCOPE_ALL.

Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoipvs: reset ipvs pointer in netns
Julian Anastasov [Tue, 24 Apr 2012 21:29:58 +0000 (00:29 +0300)]
ipvs: reset ipvs pointer in netns

Make sure net->ipvs is reset on netns cleanup or failed
initialization. It is needed for IPVS applications to know that
IPVS core is not loaded in netns.

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
12 years agoipvs: add check in ftp for initialized core
Julian Anastasov [Tue, 24 Apr 2012 21:29:59 +0000 (00:29 +0300)]
ipvs: add check in ftp for initialized core

Avoid crash when registering ip_vs_ftp after
the IPVS core initialization for netns fails. Do this by
checking for present core (net->ipvs).

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
12 years agoudp_diag: implement idiag_get_info for udp/udplite to get queue information
Shan Wei [Tue, 24 Apr 2012 18:15:41 +0000 (18:15 +0000)]
udp_diag: implement idiag_get_info for udp/udplite to get queue information

When we use netlink to monitor queue information for udp socket,
idiag_rqueue and idiag_wqueue of inet_diag_msg are returned with 0.

Keep consistent with netstat, just return back allocated rmem/wmem size.

Signed-off-by: Shan Wei <davidshan@tencent.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoMerge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville...
David S. Miller [Wed, 25 Apr 2012 19:13:37 +0000 (15:13 -0400)]
Merge branch 'for-davem' of git://git./linux/kernel/git/linville/wireless

12 years agotg3: Avoid panic from reserved statblk field access
Matt Carlson [Tue, 24 Apr 2012 13:37:01 +0000 (13:37 +0000)]
tg3: Avoid panic from reserved statblk field access

When RSS is enabled, interrupt vector 0 does not receive any rx traffic.
The rx producer index fields for vector 0's status block should be
considered reserved in this case.  This patch changes the code to
respect these reserved fields, which avoids a kernel panic when these
fields take on non-zero values.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agotlan: add cast needed for proper 64 bit operation
Benjamin Poirier [Wed, 25 Apr 2012 04:49:20 +0000 (04:49 +0000)]
tlan: add cast needed for proper 64 bit operation

Changes this beauty into a statement that actually has an effect on amd64.

Tested-by: Per Jessen <per@opensuse.org>
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
John W. Linville [Wed, 25 Apr 2012 17:41:25 +0000 (13:41 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless into for-davem

12 years agoipvs: fix crash in ip_vs_control_net_cleanup on unload
Julian Anastasov [Fri, 13 Apr 2012 15:08:43 +0000 (18:08 +0300)]
ipvs: fix crash in ip_vs_control_net_cleanup on unload

commit 14e405461e664b777e2a5636e10b2ebf36a686ec (2.6.39)
("Add __ip_vs_control_{init,cleanup}_sysctl()")
introduced regression due to wrong __net_init for
__ip_vs_control_cleanup_sysctl. This leads to crash when
the ip_vs module is unloaded.

Fix it by changing __net_init to __net_exit for
the function that is already renamed to ip_vs_control_net_cleanup_sysctl.

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
12 years agoipvs: Verify that IP_VS protocol has been registered
Sasha Levin [Sat, 14 Apr 2012 16:37:46 +0000 (12:37 -0400)]
ipvs: Verify that IP_VS protocol has been registered

The registration of a protocol might fail, there were no checks
and all registrations were assumed to be correct. This lead to
NULL ptr dereferences when apps tried registering.

For example:

[ 1293.226051] BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
[ 1293.227038] IP: [<ffffffff822aacb0>] tcp_register_app+0x60/0xb0
[ 1293.227038] PGD 391de067 PUD 6c20b067 PMD 0
[ 1293.227038] Oops: 0000 [#1] PREEMPT SMP
[ 1293.227038] CPU 1
[ 1293.227038] Pid: 19609, comm: trinity Tainted: G        W    3.4.0-rc1-next-20120405-sasha-dirty #57
[ 1293.227038] RIP: 0010:[<ffffffff822aacb0>]  [<ffffffff822aacb0>] tcp_register_app+0x60/0xb0
[ 1293.227038] RSP: 0018:ffff880038c1dd18  EFLAGS: 00010286
[ 1293.227038] RAX: ffffffffffffffc0 RBX: 0000000000001500 RCX: 0000000000010000
[ 1293.227038] RDX: 0000000000000000 RSI: ffff88003a2d5888 RDI: 0000000000000282
[ 1293.227038] RBP: ffff880038c1dd48 R08: 0000000000000000 R09: 0000000000000000
[ 1293.227038] R10: 0000000000000000 R11: 0000000000000000 R12: ffff88003a2d5668
[ 1293.227038] R13: ffff88003a2d5988 R14: ffff8800696a8ff8 R15: 0000000000000000
[ 1293.227038] FS:  00007f01930d9700(0000) GS:ffff88007ce00000(0000) knlGS:0000000000000000
[ 1293.227038] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 1293.227038] CR2: 0000000000000018 CR3: 0000000065dfc000 CR4: 00000000000406e0
[ 1293.227038] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 1293.227038] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 1293.227038] Process trinity (pid: 19609, threadinfo ffff880038c1c000, task ffff88002dc73000)
[ 1293.227038] Stack:
[ 1293.227038]  ffff880038c1dd48 00000000fffffff4 ffff8800696aada0 ffff8800694f5580
[ 1293.227038]  ffffffff8369f1e0 0000000000001500 ffff880038c1dd98 ffffffff822a716b
[ 1293.227038]  0000000000000000 ffff8800696a8ff8 0000000000000015 ffff8800694f5580
[ 1293.227038] Call Trace:
[ 1293.227038]  [<ffffffff822a716b>] ip_vs_app_inc_new+0xdb/0x180
[ 1293.227038]  [<ffffffff822a7258>] register_ip_vs_app_inc+0x48/0x70
[ 1293.227038]  [<ffffffff822b2fea>] __ip_vs_ftp_init+0xba/0x140
[ 1293.227038]  [<ffffffff821c9060>] ops_init+0x80/0x90
[ 1293.227038]  [<ffffffff821c90cb>] setup_net+0x5b/0xe0
[ 1293.227038]  [<ffffffff821c9416>] copy_net_ns+0x76/0x100
[ 1293.227038]  [<ffffffff810dc92b>] create_new_namespaces+0xfb/0x190
[ 1293.227038]  [<ffffffff810dca21>] unshare_nsproxy_namespaces+0x61/0x80
[ 1293.227038]  [<ffffffff810afd1f>] sys_unshare+0xff/0x290
[ 1293.227038]  [<ffffffff8187622e>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[ 1293.227038]  [<ffffffff82665539>] system_call_fastpath+0x16/0x1b
[ 1293.227038] Code: 89 c7 e8 34 91 3b 00 89 de 66 c1 ee 04 31 de 83 e6 0f 48 83 c6 22 48 c1 e6 04 4a 8b 14 26 49 8d 34 34 48 8d 42 c0 48 39 d6 74 13 <66> 39 58 58 74 22 48 8b 48 40 48 8d 41 c0 48 39 ce 75 ed 49 8d
[ 1293.227038] RIP  [<ffffffff822aacb0>] tcp_register_app+0x60/0xb0
[ 1293.227038]  RSP <ffff880038c1dd18>
[ 1293.227038] CR2: 0000000000000018
[ 1293.379284] ---[ end trace 364ab40c7011a009 ]---
[ 1293.381182] Kernel panic - not syncing: Fatal exception in interrupt

Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
12 years agoe1000e: Fix default interrupt throttle rate not set in NIC HW
Jeff Kirsher [Fri, 20 Apr 2012 08:51:45 +0000 (08:51 +0000)]
e1000e: Fix default interrupt throttle rate not set in NIC HW

Based on the original patch from  Ying Cai <ycai@google.com>
This change ensures that the itr/itr_setting adjustment logic is used,
even for the default/compiled-in value.

Context:
  When we changed the default InterruptThrottleRate value from default
  (3 = dynamic mode) to 8000 for example, only adapter->itr_setting
  (which controls interrupt coalescing mode) was set to 8000, but
  adapter->itr (which controls the value set in NIC register) was not
  updated accordingly. So from ethtool, it seemed the interrupt
  throttling is enabled at 8000 intr/s, but the NIC actually was
  running in dynamic mode which has lower CPU efficiency especially
  when throughput is not high.

CC: Ying Cai <ycai@google.com>
CC: David Decotigny <david.decotigny@google.com>
Signed-off-by: Jeff Kirsher <jeffrey.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
12 years agoe1000e: MSI interrupt test failed, using legacy interrupt
Prasanna S Panchamukhi [Thu, 19 Apr 2012 17:01:00 +0000 (17:01 +0000)]
e1000e: MSI interrupt test failed, using legacy interrupt

Following logs where seen on Systems with multiple NICs,
while using MSI interrupts as shown below:

Feb 16 15:09:32 (none) user.notice kernel: 0000:00:0d.0: lan0_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.notice kernel: 0000:40:0d.0: wan0_1: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.notice kernel: 0000:40:0d.0: lan0_1: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.warn kernel: 0000:40:0e.0: wan4_0: MSI interrupt
test failed, using legacy interrupt.
Feb 16 15:09:32 (none) user.notice kernel: 0000:00:0e.0: wan1_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0e.0: lan1_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0f.0: wan2_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0f.0: lan2_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:40:0a.0: wan3_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:40:0a.0: lan3_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0e.0: lan4_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0f.0: wan5_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0f.0: lan5_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX

This patch fixes this problem by increasing the msleep from 50 to 100.

Signed-off-by: Prasanna S Panchamukhi <ppanchamukhi@riverbed.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
12 years agomac80211: call ieee80211_mgd_stop() on interface stop
Eliad Peller [Mon, 23 Apr 2012 11:45:15 +0000 (14:45 +0300)]
mac80211: call ieee80211_mgd_stop() on interface stop

ieee80211_mgd_teardown() is called on netdev removal, which
occurs after the vif was already removed from the low-level
driver, resulting in the following warning:

[ 4809.014734] ------------[ cut here ]------------
[ 4809.019861] WARNING: at net/mac80211/driver-ops.h:12 ieee80211_bss_info_change_notify+0x200/0x2c8 [mac80211]()
[ 4809.030388] wlan0:  Failed check-sdata-in-driver check, flags: 0x4
[ 4809.036862] Modules linked in: wlcore_sdio(-) wl12xx wlcore mac80211 cfg80211 [last unloaded: cfg80211]
[ 4809.046849] [<c001bd4c>] (unwind_backtrace+0x0/0x12c)
[ 4809.055937] [<c047cf1c>] (dump_stack+0x20/0x24)
[ 4809.065385] [<c003e334>] (warn_slowpath_common+0x5c/0x74)
[ 4809.075589] [<c003e408>] (warn_slowpath_fmt+0x40/0x48)
[ 4809.088291] [<bf033630>] (ieee80211_bss_info_change_notify+0x200/0x2c8 [mac80211])
[ 4809.102844] [<bf067f84>] (ieee80211_destroy_auth_data+0x80/0xa4 [mac80211])
[ 4809.116276] [<bf068004>] (ieee80211_mgd_teardown+0x5c/0x74 [mac80211])
[ 4809.129331] [<bf043f18>] (ieee80211_teardown_sdata+0xb0/0xd8 [mac80211])
[ 4809.141595] [<c03b5e58>] (rollback_registered_many+0x228/0x2f0)
[ 4809.153056] [<c03b5f48>] (unregister_netdevice_many+0x28/0x50)
[ 4809.165696] [<bf041ea8>] (ieee80211_remove_interfaces+0xb4/0xdc [mac80211])
[ 4809.179151] [<bf032174>] (ieee80211_unregister_hw+0x50/0xf0 [mac80211])
[ 4809.191043] [<bf0bebb4>] (wlcore_remove+0x5c/0x7c [wlcore])
[ 4809.201491] [<c02c6918>] (platform_drv_remove+0x24/0x28)
[ 4809.212029] [<c02c4d50>] (__device_release_driver+0x8c/0xcc)
[ 4809.222738] [<c02c4e84>] (device_release_driver+0x30/0x3c)
[ 4809.233099] [<c02c4258>] (bus_remove_device+0x10c/0x128)
[ 4809.242620] [<c02c26f8>] (device_del+0x11c/0x17c)
[ 4809.252150] [<c02c6de0>] (platform_device_del+0x28/0x68)
[ 4809.263051] [<bf0df49c>] (wl1271_remove+0x3c/0x50 [wlcore_sdio])
[ 4809.273590] [<c03806b0>] (sdio_bus_remove+0x48/0xf8)
[ 4809.283754] [<c02c4d50>] (__device_release_driver+0x8c/0xcc)
[ 4809.293729] [<c02c4e2c>] (driver_detach+0x9c/0xc4)
[ 4809.303163] [<c02c3d7c>] (bus_remove_driver+0xc4/0xf4)
[ 4809.312973] [<c02c5a98>] (driver_unregister+0x70/0x7c)
[ 4809.323220] [<c03809c4>] (sdio_unregister_driver+0x24/0x2c)
[ 4809.334213] [<bf0df458>] (wl1271_exit+0x14/0x1c [wlcore_sdio])
[ 4809.344930] [<c009b1a4>] (sys_delete_module+0x228/0x2a8)
[ 4809.354734] ---[ end trace 515290ccf5feb522 ]---

Rename ieee80211_mgd_teardown() to ieee80211_mgd_stop(),
and call it on ieee80211_do_stop().

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoiwlwifi: use correct released ucode version
Meenakshi Venkataraman [Sun, 22 Apr 2012 14:55:27 +0000 (07:55 -0700)]
iwlwifi: use correct released ucode version

Report correctly the latest released version
of the iwlwifi firmware for all
iwlwifi-supported devices.

Cc: stable@vger.kernel.org #3.3+
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoiwlwifi: fix hardware queue programming
Johannes Berg [Mon, 23 Apr 2012 21:17:50 +0000 (14:17 -0700)]
iwlwifi: fix hardware queue programming

Newer devices have 20 (5000 series) or 30 (6000 series)
hardware queues, rather than the 16 that 4965 had. This
was added to the driver a long time ago, but improperly:
the queue registers for the higher queues aren't just
continuations of the registers for the first 16 queues,
they are in other places. Therefore, the hardware would
lock up when trying to activate queue 16 or above and
the device would have to be restarted.

Thanks goes to Emmanuel who identified this and told me
how the queue programming should be done.

Note that we don't use queues 20 and higher today and
doing so needs more work than this.

Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoAdd Foxconn / Hon Hai IDs for btusb module
Steven Harms [Fri, 13 Apr 2012 18:45:55 +0000 (14:45 -0400)]
Add Foxconn / Hon Hai IDs for btusb module

This change adds 0x0489:0xe033 to the btusb module.

This bluetooth usb device is integrated in the Acer TimelineX AS4830TG-6808 notebook.

Output from /sys/kernel/debug/usb/devices:

T:  Bus=01 Lev=02 Prnt=02 Port=05 Cnt=02 Dev#=  4 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e033 Rev= 2.29
S:  Manufacturer=Broadcom Corp
S:  Product=Acer Module
S:  SerialNumber=60D819F74101
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  32 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  32 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Signed-off-by: Steven Harms <sjharms@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
12 years agoBluetooth: Fix missing break in hci_cmd_complete_evt
Szymon Janc [Fri, 13 Apr 2012 10:32:42 +0000 (12:32 +0200)]
Bluetooth: Fix missing break in hci_cmd_complete_evt

Command complete event for HCI_OP_USER_PASSKEY_NEG_REPLY would result
in calling handler function also for HCI_OP_LE_SET_SCAN_PARAM. This
could result in undefined behaviour.

Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
12 years agoasix: Fix tx transfer padding for full-speed USB
Ingo van Lil [Mon, 23 Apr 2012 22:05:38 +0000 (22:05 +0000)]
asix: Fix tx transfer padding for full-speed USB

The asix.c USB Ethernet driver avoids ending a tx transfer with a zero-
length packet by appending a four-byte padding to transfers whose length
is a multiple of maxpacket. However, the hard-coded 512 byte maxpacket
length is valid for high-speed USB only; full-speed USB uses 64 byte
packets.

Signed-off-by: Ingo van Lil <inguin@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agonet/davinci_emac: fix failing PHY connect attempts
Anatolij Gustschin [Mon, 23 Apr 2012 12:06:43 +0000 (12:06 +0000)]
net/davinci_emac: fix failing PHY connect attempts

PHY connect attempts fail if no PHY id is specified in the emac platform
data and another mdio bus has been registered before 'davinci_mdio' bus. In
this case when configuring the interface, there will be an attempt to
connect to already attached PHY on the previously registered mdio bus:

net eth1: PHY already attached
net eth1: could not connect to phy smsc911x-0:01
IP-Config: Failed to open eth1
IP-Config: Device `eth1' not found

Fix this by modifying match_first_device() to match first PHY device
on 'davinci_mdio' bus.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoehea: only register irq after setting up ports
Thadeu Lima de Souza Cascardo [Mon, 23 Apr 2012 03:46:29 +0000 (03:46 +0000)]
ehea: only register irq after setting up ports

If we receive an interrupt too early before we set up ports in the probe
function, there won't be any port ready to handle it.

Only registering the irq after the ports are setup fixes the problem,
and works fine without losing any interrupts.

This causes crashes in some situations:

[c000000f7ff7fd60d000000008e223f0 .ehea_neq_tasklet+0x78/0x148 [ehea]
[c000000f7ff7fe00c0000000000b6cac .tasklet_hi_action+0xdc/0x210
[c000000f7ff7fea0c0000000000b7cc8 .__do_softirq+0x178/0x300
[c000000f7ff7ff90c000000000022694 .call_do_softirq+0x14/0x24
[c000000f68ee7900c000000000010e04 .do_softirq+0xec/0x110
[c000000f68ee79a0c0000000000b789c .irq_exit+0xac/0xe0
[c000000f68ee7a20c0000000000110bc .do_IRQ+0x114/0x2a8
[c000000f68ee7ae0c00000000000553c hardware_interrupt_entry+0x18/0x1c

Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoqeth: Use blkt defaults for OSA Express 4
Stefan Raspl [Sun, 22 Apr 2012 21:21:42 +0000 (21:21 +0000)]
qeth: Use blkt defaults for OSA Express 4

The previous blkt defaults for OSA Express 4 cards produced inadequate
performance for streaming workloads. The present patch will apply a
set of more appropriate defaults.

Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoqeth: allow change of blkt default values
Ursula Braun [Sun, 22 Apr 2012 21:21:41 +0000 (21:21 +0000)]
qeth: allow change of blkt default values

There exist qeth sysfs blkt attributes to change the default blkt
values. But blkt changes are reset during online setting due to a 2nd
invocation of qeth_determine_capabilites(). This patch makes sure
blkt default values are configured during 1st run of
qeth_determine_capabilities() only. Thus blkt changes are kept
during online setting.

Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Reported-by: Horst Hartmann <horst.hartmann@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agonet: usb: smsc95xx: fix mtu
Stephane Fillod [Fri, 20 Apr 2012 09:39:23 +0000 (09:39 +0000)]
net: usb: smsc95xx: fix mtu

Make smsc95xx recalculate the hard_mtu after adjusting the
hard_header_len.

Without this, usbnet adjusts the MTU down to 1488 bytes, and the host is
unable to receive standard 1500-byte frames from the device.

Inspired by same fix on cdc_eem 78fb72f7936c01d5b426c03a691eca082b03f2b9.

Tested on ARM/Beagle.

Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoset fake_rtable's dst to NULL to avoid kernel Oops
Peter Huang (Peng) [Thu, 19 Apr 2012 20:12:51 +0000 (20:12 +0000)]
set fake_rtable's dst to NULL to avoid kernel Oops

bridge: set fake_rtable's dst to NULL to avoid kernel Oops

when bridge is deleted before tap/vif device's delete, kernel may
encounter an oops because of NULL reference to fake_rtable's dst.
Set fake_rtable's dst to NULL before sending packets out can solve
this problem.

v4 reformat, change br_drop_fake_rtable(skb) to {}

v3 enrich commit header

v2 introducing new flag DST_FAKE_RTABLE to dst_entry struct.

[ Use "do { } while (0)" for nop br_drop_fake_rtable()
  implementation -DaveM ]

Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Peter Huang <peter.huangpeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoMerge branch 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Linus Torvalds [Tue, 24 Apr 2012 02:45:19 +0000 (19:45 -0700)]
Merge branch 'rc-fixes' of git://git./linux/kernel/git/mmarek/kbuild

Pull build system failure fix from Michal Marek:
 "This fixes build failure with newer gcc that adds some internal
  symbols that end in "__mod_*_device_table", but are not actually the
  tables themselves."

* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  Fix modpost failures in fedora 17

12 years agoMerge tag 'md-3.4-fixes' of git://neil.brown.name/md
Linus Torvalds [Tue, 24 Apr 2012 01:25:01 +0000 (18:25 -0700)]
Merge tag 'md-3.4-fixes' of git://neil.brown.name/md

Pull a few more md bug fixes from NeilBrown:
 "2 are tagged for -stable, one being for a fairly serious bug that can
  corrupt metadata and make it hard to recovery an array.  The other is
  for a more recent regression since 3.3"

* tag 'md-3.4-fixes' of git://neil.brown.name/md:
  md: fix possible corruption of array metadata on shutdown.
  md: don't call ->add_disk unless there is good reason.
  DM RAID: Use safe version of rdev_for_each

12 years agoMerge tag 'dlm-fixes-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland...
Linus Torvalds [Tue, 24 Apr 2012 01:22:42 +0000 (18:22 -0700)]
Merge tag 'dlm-fixes-3.4' of git://git./linux/kernel/git/teigland/linux-dlm

Pull dlm fixes from David Teigland:
 "This includes one short patch fixing the behavior of the QUECVT flag,
  which the gfs2 folks are waiting on."

* tag 'dlm-fixes-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
  dlm: fix QUECVT when convert queue is empty

12 years agomm: fix s390 BUG by __set_page_dirty_no_writeback on swap
Hugh Dickins [Mon, 23 Apr 2012 18:14:50 +0000 (11:14 -0700)]
mm: fix s390 BUG by __set_page_dirty_no_writeback on swap

Mel reports a BUG_ON(slot == NULL) in radix_tree_tag_set() on s390
3.0.13: called from __set_page_dirty_nobuffers() when page_remove_rmap()
tries to transfer dirty flag from s390 storage key to struct page and
radix_tree.

That would be because of reclaim's shrink_page_list() calling
add_to_swap() on this page at the same time: first PageSwapCache is set
(causing page_mapping(page) to appear as &swapper_space), then
page->private set, then tree_lock taken, then page inserted into
radix_tree - so there's an interval before taking the lock when the
radix_tree slot is empty.

We could fix this by moving __add_to_swap_cache()'s spin_lock_irq up
before the SetPageSwapCache.  But a better fix is simply to do what's
five years overdue: Ken Chen introduced __set_page_dirty_no_writeback()
(if !PageDirty TestSetPageDirty) for tmpfs to skip all the radix_tree
overhead, and swap is just the same - it ignores the radix_tree tag, and
does not participate in dirty page accounting, so should be using
__set_page_dirty_no_writeback() too.

s390 testing now confirms that this does indeed fix the problem.

Reported-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ken Chen <kenchen@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
12 years agomd: fix possible corruption of array metadata on shutdown.
NeilBrown [Tue, 24 Apr 2012 00:23:16 +0000 (10:23 +1000)]
md: fix possible corruption of array metadata on shutdown.

commit c744a65c1e2d59acc54333ce8
  md: don't set md arrays to readonly on shutdown.

removed the possibility of a 'BUG' when data is written to an array
that has just been switched to read-only, but also introduced the
possibility that the array metadata could be corrupted.

If, when md_notify_reboot gets the mddev lock, the array is
in a state where it is assembled but hasn't been started (as can
happen if the personality module is not available, or in other unusual
situations), then incorrect metadata will be written out making it
impossible to re-assemble the array.

So only call __md_stop_writes() if the array has actually been
activated.

This patch is needed for any stable kernel which has had the above
commit applied.

Cc: stable@vger.kernel.org
Reported-by: Christoph Nelles <evilazrael@evilazrael.de>
Signed-off-by: NeilBrown <neilb@suse.de>
12 years agomd: don't call ->add_disk unless there is good reason.
NeilBrown [Tue, 24 Apr 2012 00:23:14 +0000 (10:23 +1000)]
md: don't call ->add_disk unless there is good reason.

Commit 7bfec5f35c68121e7b18

   md/raid5: If there is a spare and a want_replacement device, start replacement.

cause md_check_recovery to call ->add_disk much more often.
Instead of only when the array is degraded, it is now called whenever
md_check_recovery finds anything useful to do, which includes
updating the metadata for clean<->dirty transition.
This causes unnecessary work, and causes info messages from ->add_disk
to be reported much too often.

So refine md_check_recovery to only do any actual recovery checking
(including ->add_disk) if MD_RECOVERY_NEEDED is set.

This fix is suitable for 3.3.y:

Cc: stable@vger.kernel.org
Reported-by: Jan Ceuleers <jan.ceuleers@computer.org>
Signed-off-by: NeilBrown <neilb@suse.de>
12 years agoDM RAID: Use safe version of rdev_for_each
Jonathan Brassow [Tue, 24 Apr 2012 00:23:13 +0000 (10:23 +1000)]
DM RAID: Use safe version of rdev_for_each

Fix segfault caused by using rdev_for_each instead of rdev_for_each_safe

Commit dafb20fa34320a472deb7442f25a0c086e0feb33 mistakenly replaced a safe
iterator with an unsafe one when making some macro changes.

Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
12 years agobrcmsmac: "INTERMEDIATE but not AMPDU" only when tracing
Eldad Zack [Sat, 21 Apr 2012 22:48:04 +0000 (00:48 +0200)]
brcmsmac: "INTERMEDIATE but not AMPDU" only when tracing

I keep getting the following messages on the log buffer:
[ 2167.097507] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2281.331305] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2281.332539] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2329.876605] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2329.877354] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2462.280756] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2615.651689] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU

From the code comment I understand that this something that can -
and does, quite frequently - happen.

Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Acked-by: Franky Lin<frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agortlwifi: Fix oops on unload
Larry Finger [Fri, 20 Apr 2012 02:39:06 +0000 (21:39 -0500)]
rtlwifi: Fix oops on unload

Under some circumstances, a PCI-based driver reports the following OOPs:

Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Oops: 0000 [#1] SMP
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Pid: 19627, comm: rmmod
Not tainted 3.2.9-2.fc16.x86_64 #1 LENOVO 05962RU/05962RU
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] RIP:
0010:[<ffffffffa0418d39>]  [<ffffffffa0418d39>]
rtl92ce_get_desc+0x19/0xd0 [rtl8192ce]
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Process rmmod (pid:
19627, threadinfo ffff880050262000, task ffff8801156d5cc0)
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Stack:
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  0000000000000002
ffff8801176c2540 ffff880050263ca8 ffffffffa03348e7
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  0000000000000282
0000000180150014 ffff880050263fd8 ffff8801176c2810
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  ffff880050263bc8
ffffffff810550e2 00000000000002c0 ffff8801176c0d40
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Call Trace:
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  [<ffffffffa03348e7>]
_rtl_pci_rx_interrupt+0x187/0x650 [rtlwifi]
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Code: ff 09 d0 89 07 48
83 c4 08 5b 5d c3 66 0f 1f 44 00 00 55 48 89 e5 53 48 83 ec 08 66 66
66 66 90 40 84 f6 89 d3 74 13 84 d2 75 57 <8b> 07 48 83 c4 08 5b 5d c1
e8 1f c3 0f 1f 00 84 d2 74 ed 80 fa
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] RIP
[<ffffffffa0418d39>] rtl92ce_get_desc+0x19/0xd0 [rtl8192ce]
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  RSP <ffff880050263b58>
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] CR2: 00000000000006e0
Mar 19 08:14:35 kvothe kernel: [ 6584.646491] ---[ end trace
8636c766dcfbe0e6 ]---

This oops is due to interrupts not being disabled in this particular path.

Reported-by: Dave Airlie <airlied@gmail.com>
Tested-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoipw2200: Fix race condition in the command completion acknowledge
Stanislav Yakovlev [Thu, 19 Apr 2012 19:55:09 +0000 (15:55 -0400)]
ipw2200: Fix race condition in the command completion acknowledge

Driver incorrectly validates command completion: instead of waiting
for a command to be acknowledged it continues execution.  Most of the
time driver gets acknowledge of the command completion in a tasklet
before it executes the next one. But sometimes it sends the next
command before it gets acknowledge for the previous one. In such a
case one of the following error messages appear in the log:

Failed to send SYSTEM_CONFIG: Already sending a command.
Failed to send ASSOCIATE: Already sending a command.
Failed to send TX_POWER: Already sending a command.

After that you need to reload the driver to get it working again.

This bug occurs during roaming (reported by Sam Varshavchik)
https://bugzilla.redhat.com/show_bug.cgi?id=738508
and machine booting (reported by Tom Gundersen and Mads Kiilerich)
https://bugs.archlinux.org/task/28097
https://bugzilla.redhat.com/show_bug.cgi?id=802106

This patch doesn't fix the delay issue during firmware load.
But at least device now works as usual after boot.

Cc: stable@kernel.org
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoiwlwifi: do not nulify ctx->vif on reset
Stanislaw Gruszka [Wed, 18 Apr 2012 15:01:15 +0000 (08:01 -0700)]
iwlwifi: do not nulify ctx->vif on reset

ctx->vif is dereferenced in different part of iwlwifi code, so do not
nullify it.

This should address at least one of the possible reasons of WARNING at
iwlagn_mac_remove_interface, and perhaps some random crashes when
firmware reset is performed.

Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoath9k: fix tx power settings for AR9287
Gabor Juhos [Sun, 15 Apr 2012 18:38:06 +0000 (20:38 +0200)]
ath9k: fix tx power settings for AR9287

The 'ath9k_hw_update_regulatory_maxpower'
helper function has been introduced by
commit a55f858852e4345d0a31af593c46738ca8614bff
(ath9k_hw: Cleanup TX power calculation for AR9287).

Updating of the max_power_level value has been moved
into the helper function in that change, however the
removed code from 'ath9k_hw_ar9287_set_txpower' has
not been replaced with a call of the new helper
function.

Due to that missing call, retrieving tx power for 2x2
and 3x3 chainmask is not handled properly. During the
calculation of the tx power for 2x2 and 3x3 chainmasks
the values are reduced. Those reductions must be
compensated during retrieving.

Fix this by adding the missing call of the helper
function.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoath9k: add an extra boolean parameter to ath9k_hw_apply_txpower
Gabor Juhos [Sun, 15 Apr 2012 18:38:05 +0000 (20:38 +0200)]
ath9k: add an extra boolean parameter to ath9k_hw_apply_txpower

In order to unifying regulatory limit handling
commit ca2c68cc7bc80fc4504fb420df04cce99c9ee6ec
(ath9k_hw: clean up tx power handling) introduced
a new helper function 'ath9k_hw_apply_txpower',
and the direct calls of 'ah->eep_ops->set_txpower'
has been replaced by a call of the helper function.

This caused a change in the behaviour of the
'ath9k_hw_set_txpowerlimit' function. The purpose
of that function is to calculate and store the
rate txpower table and the regulatory limit without
touching the hardware registers. Before the commit,
the 'test' parameter of the function was passed to
the 'ah->eep_ops->set_txpower'. Now the calling of
the 'set_txpower' function happens indirectly through
'ath9k_hw_apply_txpower', so the 'test' argument of
the 'set_txpower' is always 'false'.

This patch restores the original behaviour of
'ath9k_hw_set_txpowerlimit' by adding a new
argument to 'ath9k_hw_apply_txpower.'

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agodlm: fix QUECVT when convert queue is empty
David Teigland [Wed, 4 Apr 2012 14:49:15 +0000 (09:49 -0500)]
dlm: fix QUECVT when convert queue is empty

The QUECVT flag should not prevent conversions from
being granted immediately when the convert queue is
empty.

Signed-off-by: David Teigland <teigland@redhat.com>
12 years agoMerge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Linus Torvalds [Mon, 23 Apr 2012 04:19:15 +0000 (21:19 -0700)]
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm

Pull ARM fixes from Russell King:
 "Here's my usual Sunday push, just for one revert which PeterZ hollered
  about after last weeks push.  Other than that, all seems strangely
  quiet as far as fixes go in non-platform ARM land at the moment."

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  Revert "ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus"

12 years agoMerge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Linus Torvalds [Mon, 23 Apr 2012 04:07:51 +0000 (21:07 -0700)]
Merge branch 'merge' of git://git./linux/kernel/git/benh/powerpc

Pull powerpc fixes from Benjamin Herrenschmidt:
 "Here are a few fixes for powerpc.  Note the addition to the generic
  irq.h.  This is part of a 3-patches regression fix for mpic due to
  changes in how IRQ_TYPE_NONE is being handled.  Thomas agreed to the
  addition of the new IRQ_TYPE_DEFAULT contant, however he hasn't
  replied with an Ack to the actual patch yet.  I don't to wait much
  longer with these patches tho."

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/mpic: Properly set default triggers
  irq: Add IRQ_TYPE_DEFAULT for use by PIC drivers
  powerpc/mpic: Fix confusion between hw_irq and virq
  powerpc/pmac: Don't add_timer() twice
  powerpc/eeh: Fix crash caused by null eeh_dev
  powerpc/mpc85xx: add MPIC message dts node
  powerpc/mpic_msgr: fix offset error when setting mer register
  powerpc/mpic_msgr: add lock for MPIC message global variable
  powerpc/mpic_msgr: fix compile error when SMP disabled
  powerpc: fix build when CONFIG_BOOKE_WDT is enabled
  powerpc/85xx: don't call of_platform_bus_probe() twice

12 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Linus Torvalds [Mon, 23 Apr 2012 04:02:57 +0000 (21:02 -0700)]
Merge git://git./linux/kernel/git/davem/net

Pull networking fixes from David Miller:

 1) Fix namespace init and cleanup in phonet to fix some oopses, from
    Eric W. Biederman.

 2) Missing kfree_skb() in AF_KEY, from Julia Lawall.

 3) Refcount leak and source address handling fix in l2tp from James
    Chapman.

 4) Memory leak fix in CAIF from Tomasz Gregorek.

 5) When routes are cloned from ipv6 addrconf routes, we don't process
    expirations properly.  Fix from Gao Feng.

 6) Fix panic on DMA errors in atl1 driver, from Tony Zelenoff.

 7) Only enable interrupts in 8139cp driver after we've registered the
    IRQ handler.  From Jason Wang.

 8) Fix too many reads of KS_CIDER register in ks8851 during probe,
    fixing crashes on spurious interrupts.  From Matt Renzelmann.

 9) Missing include in ath5k driver and missing iounmap on probe
    failure, from Jonathan Bither.

10) Fix RX packet handling in smsc911x driver, from Will Deacon.

11) Fix ixgbe WoL on fiber by leaving the laser on during shutdown.

12) ks8851 needs MAX_RECV_FRAMES increased otherwise the internal MAC
    buffers are easily overflown.  Fix from Davide Cimingahi.

13) Fix memory leaks in peak_usb CAN driver, from Jesper Juhl.

14) gred packet scheduler can dump in WRED more when doing a netlink
    dump.  Fix from David Ward.

15) Fix MTU in USB smsc75xx driver, from Stephane Fillod.

16) Dummy device needs ->ndo_uninit handler to properly handle
    ->ndo_init failures.  From Hiroaki SHIMODA.

17) Fix TX fragmentation in ath9k driver, from Sujith Manoharan.

18) Missing RTNL lock in ixgbe PM resume, from Benjamin Poirier.

19) Missing iounmap in farsync WAN driver, from Julia Lawall.

20) With LRO/GRO, tcp_grow_window() is easily tricked into not growing
    the receive window properly, and this hurts performance.  Fix from
    Eric Dumazet.

21) Network namespace init failure can leak net_generic data, fix from
    Julian Anastasov.

22) Fix skb_over_panic due to mis-accounting in TCP for partially ACK'd
    SKBs.  From Eric Dumazet.

23) New IDs for qmi_wwan driver, from Bjørn Mork.

24) Fix races in ax25_exit(), from Eric W. Biederman.

25) IPV6 TCP doesn't handle TCP_MAXSEG socket option properly, copy over
    logic from the IPV4 side.  From Neal Cardwell.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
  tcp: fix TCP_MAXSEG for established IPv6 passive sockets
  drivers/net: Do not free an IRQ if its request failed
  drop_monitor: allow more events per second
  ks8851: Fix request_irq/free_irq mismatch
  net/hyperv: Adding cancellation to ensure rndis filter is closed
  ks8851: Fix mutex deadlock in ks8851_net_stop()
  net ax25: Reorder ax25_exit to remove races.
  icplus: fix interrupt for IC+ 101A/G and 1001LF
  net: qmi_wwan: support Sierra Wireless MC77xx devices in QMI mode
  bnx2x: off by one in bnx2x_ets_e3b0_sp_pri_to_cos_set()
  ksz884x: don't copy too much in netdev_set_mac_address()
  tcp: fix retransmit of partially acked frames
  netns: do not leak net_generic data on failed init
  net/sock.h: fix sk_peek_off kernel-doc warning
  tcp: fix tcp_grow_window() for large incoming frames
  drivers/net/wan/farsync.c: add missing iounmap
  davinci_mdio: Fix MDIO timeout check
  ipv6: clean up rt6_clean_expires
  ipv6: fix rt6_update_expires
  arcnet: rimi: Fix device name in debug output
  ...

12 years agopowerpc/mpic: Properly set default triggers
Benjamin Herrenschmidt [Thu, 19 Apr 2012 17:30:57 +0000 (17:30 +0000)]
powerpc/mpic: Properly set default triggers

This gets rid of the unused default senses array, and replaces the
incorrect use of IRQ_TYPE_NONE with the new IRQ_TYPE_DEFAULT for
the initial set_trigger() call when mapping an interrupt.

This in turn makes us read the HW state and update the irq desc
accordingly.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
12 years agoirq: Add IRQ_TYPE_DEFAULT for use by PIC drivers
Benjamin Herrenschmidt [Thu, 19 Apr 2012 17:29:42 +0000 (17:29 +0000)]
irq: Add IRQ_TYPE_DEFAULT for use by PIC drivers

This is meant typically to allow a PIC driver's irq domain map() callback
to establish sane defaults for the interrupt (and make sure that the HW
and the irq_desc are in sync as far as the trigger is concerned).

The irq core may not call the set_trigger callback if it thinks the
trigger is already set to the right setting, so we need to ensure new
descriptors are properly synchronized with the hardware.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
12 years agopowerpc/mpic: Fix confusion between hw_irq and virq
Benjamin Herrenschmidt [Thu, 19 Apr 2012 17:29:34 +0000 (17:29 +0000)]
powerpc/mpic: Fix confusion between hw_irq and virq

mpic_is_ipi() takes a virq and immediately converts it to a hw_irq.

However, one of the two call sites calls it with a ... hw_irq. The
other call site also happens to have the hw_irq at hand, so let's
change it to just take that as an argument. Also change mpic_is_tm()
for consistency.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
12 years agopowerpc/pmac: Don't add_timer() twice
Benjamin Herrenschmidt [Wed, 18 Apr 2012 22:16:48 +0000 (22:16 +0000)]
powerpc/pmac: Don't add_timer() twice

If the interrupt and the timeout happen roughly at the same
time, we can get into a situation where the timer function
is run while the interrupt has already been processed. In
this case, the timer function might end up doing an add_timer
on an already pending timer, causing a BUG_ON() to trigger.

Instead, just skip the whole timeout operation if we see that
the timer is pending. The spinlock ensures that the only way
that happens is if we already started a new operation and thus
the timeout can be ignored.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
12 years agopowerpc/eeh: Fix crash caused by null eeh_dev
Gavin Shan [Mon, 16 Apr 2012 19:55:39 +0000 (19:55 +0000)]
powerpc/eeh: Fix crash caused by null eeh_dev

The problem was reported by Anton Blanchard. While EEH error
happened to the PCI device without the corresponding device
driver, kernel crash was seen. Eventually, I successfully
reproduced the problem on Firebird-L machine with utility
"errinjct". Initially, the device driver for Emulex ethernet
MAC has been disabled from .config and force data parity on
the Emulex ethernet MAC with help of "errinjct". Eventually,
I saw the kernel crash after issueing couple of "lspci -v"
command.

The root cause behind is that the PCI device, including the
reference to the corresponding eeh device, will be removed
from the system while EEH does recovery. Afterwards, the
PCI device will be probed again and added into the system
accordingly. So it's not safe to retrieve the eeh device from
the corresponding PCI device after the PCI device has been removed
and not added again.

The patch fixes the issue and retrieve the eeh device from OF node
instead of PCI device after the PCI device has been removed.

Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Tested-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
12 years agoMerge remote-tracking branch 'kumar/merge' into merge
Benjamin Herrenschmidt [Mon, 23 Apr 2012 00:55:20 +0000 (10:55 +1000)]
Merge remote-tracking branch 'kumar/merge' into merge

12 years agotcp: fix TCP_MAXSEG for established IPv6 passive sockets
Neal Cardwell [Sun, 22 Apr 2012 09:45:47 +0000 (09:45 +0000)]
tcp: fix TCP_MAXSEG for established IPv6 passive sockets

Commit f5fff5d forgot to fix TCP_MAXSEG behavior IPv6 sockets, so IPv6
TCP server sockets that used TCP_MAXSEG would find that the advmss of
child sockets would be incorrect. This commit mirrors the advmss logic
from tcp_v4_syn_recv_sock in tcp_v6_syn_recv_sock. Eventually this
logic should probably be shared between IPv4 and IPv6, but this at
least fixes this issue.

Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoLinux 3.4-rc4
Linus Torvalds [Sat, 21 Apr 2012 21:47:52 +0000 (14:47 -0700)]
Linux 3.4-rc4

12 years agodrivers/net: Do not free an IRQ if its request failed
Lee Jones [Thu, 19 Apr 2012 10:36:33 +0000 (10:36 +0000)]
drivers/net: Do not free an IRQ if its request failed

Refrain from attempting to free an interrupt line if the request
fails and hence, there is no IRQ to free.

CC: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agosparc32,leon: add notify_cpu_starting()
Yong Zhang [Thu, 19 Apr 2012 20:28:32 +0000 (20:28 +0000)]
sparc32,leon: add notify_cpu_starting()

Otherwise cpu_active_mask will not set, which lead to other issue.

Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Konrad Eisele <konrad@gaisler.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agodrop_monitor: allow more events per second
Eric Dumazet [Thu, 19 Apr 2012 07:16:21 +0000 (07:16 +0000)]
drop_monitor: allow more events per second

It seems there is a logic error in trace_drop_common(), since we store
only 64 drops, even if they are from same location.

This fix is a one liner, but we probably need more work to avoid useless
atomic dec/inc

Now I can watch 1 Mpps drops through dropwatch...

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoks8851: Fix request_irq/free_irq mismatch
Matt Renzelmann [Thu, 19 Apr 2012 07:17:17 +0000 (07:17 +0000)]
ks8851: Fix request_irq/free_irq mismatch

The dev_id parameter passed to free_irq needs to match the one passed
to the corresponding request_irq.

Signed-off-by: Matt Renzelmann <mjr@cs.wisc.edu>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoMerge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm...
Linus Torvalds [Sat, 21 Apr 2012 19:45:52 +0000 (12:45 -0700)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc

Pull "ARM: SoC fixes" from Olof Johansson:
 * at91, ux500, imx, omap and bcmring:
  - at91 fixes for =m driver build issues, irqdomain fixes and config
    dependency fixes
  - ux500 kconfig dependency fixes and a  smp wakeup bugfix
  - imx idle bugfix and build fix due to irq domain changes
  - omap uart pinmux fixes, softreset regression revert and misc fixes
  - bcmring build error regression fix

 * ux500 and imx had some small defconfig updates in this branch

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
  ARM: bcmring: fix UART declarations
  ARM: imx: Fix imx5 idle logic bug
  ARM: imx27-dt: Fix build due to removal of irq_domain_add_simple()
  ARM: imx_v4_v5_defconfig: Add support for CONFIG_REGULATOR_FIXED_VOLTAGE
  ARM: OMAP1: DMTIMER: fix broken timer clock source selection
  ARM: OMAP: serial: Fix the ocp smart idlemode handling bug
  ARM: OMAP2+: UART: Fix incorrect population of default uart pads
  ARM: OMAP: sram: fix BUG in dpll code for !PM case
  dmaengine: Kconfig: fix Atmel at_hdmac entry
  USB: gadget/at91_udc: add gpio_to_irq() function to vbus interrupt
  USB: ohci-at91: change annotations for probe/remove functions
  leds-atmel-pwm.c: Make pwmled_probe() __devinit
  ARM: at91: fix at91sam9261ek Ethernet dm9000 irq
  ARM: at91: fix rm9200ek flash size
  ARM: at91: remove empty at91_init_serial function
  ARM: at91: fix typo in at91_pmc_base assembly declaration
  ARM: at91: Export at91_matrix_base
  ARM: at91: Export at91_pmc_base
  ARM: at91: Export at91_ramc_base
  ARM: at91: Export at91_st_base
  ...