[IA64] fix call of smp_processor_id() by XPC while

XPC calls smp_processor_id() twice from xpc_setup_infrastructure() with
preemption enabled, which gets flagged if 'DEBUG_PREEMPT=y'. This patch
replaces the two calls to smp_processor_id() by a single call to
raw_smp_processor_id() since any CPU within the partition will do.

Signed-off-by: Dean Nelson <dcn@sgi.com>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>

[IA64] Altix pcibus_to_node implementation

The Altix subarch does not provide node information via ACPI. Instead hooks
are used to fixup pci structures. This patch determines the nodes for Altix
PCI busses.

Remote Bridges:
---------------
Altix supports remote I/O nodes without memory or processors but with bridges.
The TIOCA type of bridge is an AGP bridge and the PROM provides information
about the closest node. That information will be returned by pcibus_to_node.

The TIOCP remote bridge type is a PCI bridge but the PROM does not provide a
closest node id. pcibus_to_node will return -1 for devices on those bridges
meaning that device control structures may be allocated on any node.

Safeguard:
----------
Should the fixups result in invalid node information for a pci controller then
a warning will be printed and pcibus_to_node will return -1.

This patch also fixes the "FIXME" in sn_dma_alloc_coherent. This means that
dma_alloc_coherent will now use alloc_pages_node to allocate memory local to
the node that the PCI device is connected to.

Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

[IA64] improve flush_icache_range()

Check with PAL to see what the i-cache line size is for
each level of the cache, and so use the correct stride
when flushing the cache.

Acked-by: David Mosberger
Signed-off-by: Tony Luck <tony.luck@intel.com>

[IA64] remove CONFIG_IA64_SGI_SN_SIM

This patch removes the CONFIG_IA64_SGI_SN_SIM option entirely, allowing
any kernel bootable on sn2 to also be booted in the simulator.

Boot tested on Altix and HP rx2600.

Signed-off-by: Greg Edwards <edwardsg@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

[IA64] pcibus_to_node implementation for IA64

pcibus_to_node provides a way for the Linux kernel to identify to which
node a certain pcibus connects to. Allocations of control structures
for devices can then be made on the node where the pci bus is located
to allow local access during interrupt and other device manipulation.

This patch provides a new "node" field in the the pci_controller
structure. The node field will be set based on ACPI information (thanks
to Alex Williamson  <alex.williamson@hp.com for that piece).

Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Merge /pub/scm/linux/kernel/git/aegl/linux-2.6

[IA64] assign_irq_vector() should not panic

Current assign_irq_vector() will panic if interrupt vectors is running
out. But I think how to handle the case of lack of interrupt vectors
should be handled by the caller of this function. For example, some
PCI devices can raise the interrupt signal via both MSI and I/O
APIC. So even if the driver for these device fails to allocate a
vector for MSI, the driver still has a chance to use I/O APIC based
interrupt. But currently there is no chance for these driver to use
I/O APIC based interrupt because kernel will panic when
assign_irq_vector() fails to allocate interrupt vector.

The following patch changes assign_irq_vector() for ia64 to return
-ENOSPC on error instead of panic (as i386 and x86_64 versions do).

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

[IA64] use msleep_interruptible() instead of schedule_timeout

Description: Replace schedule_timeout() with msleep_interruptible() to
guarantee the task delays as expected.

Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

[PATCH] v850: Update mmu.h header to match implementation changes

Signed-off-by: Miles Bader <miles@gnu.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] v850: Update checksum.h to match changed function signatures

Signed-off-by: Miles Bader <miles@gnu.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Merge /pub/scm/linux/kernel/git/tglx/mtd-2.6

Merge /pub/scm/linux/kernel/git/davem/sparc-2.6

[IA64] remove linux/version.h include from arch/ia64

changing CONFIG_LOCALVERSION rebuilds too much, for no appearent reason.

Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Auto merge with /home/aegl/GIT/linus

[SPARC64]: Add syscall auditing support.

Signed-off-by: David S. Miller <davem@davemloft.net>

[SPARC64]: Pass regs and entry/exit boolean to syscall_trace()

Also fix a bug in 32-bit syscall tracing.  We forgot to update
this code when we moved over to the convention that all 32-bit
syscall arguments are zero extended by default.

Signed-off-by: David S. Miller <davem@davemloft.net>

[SPARC64]: Add SECCOMP support.

Signed-off-by: David S. Miller <davem@davemloft.net>

[SPARC64]: Kill ancient and unused SYSCALL_TRACING debugging code.

Signed-off-by: David S. Miller <davem@davemloft.net>

[SPARC64]: Add __read_mostly support.

Signed-off-by: David S. Miller <davem@davemloft.net>

[SPARC]: Add ioprio system call support.

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge master.kernel.org:~rmk/linux-2.6-arm.git

[PATCH] remove asm-xtensa/ipc.h

Now that sys_ipc has been removed from xtensa, asm/ipc.h is no longer
needed for that architecture.  Not tested, but obviously correct.  This
file is included only from arch code and this patch also removes the only
inclusion.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] Sync up ieee-1394

Lots of this patch is trivial code cleanups (static vars were being
intialized to 0, etc).

There's also some fixes for ISO transmits (max buffer handling).
Aswell, we have a few fixes to disable IRM capabilites correctly.  We've
also disabled, by default some generally unused EXPORT symbols for the
sake of cleanliness in the kernel.  However, instead of removing them
completely, we felt it necessary to have a config option that allowed
them to be enabled for the many projects outside of the main kernel tree
that use our API for driver development.

The primary reason for this patch is to revert a MODE6->MODE10 RBC
conversion patch from the SCSI maintainers.  The new conversions handled
directly in the scsi layer do not seem to work for SBP2.  This patch
reverts to our old working code so that users can enjoy using Firewire
disks and dvd drives again.

We are working with the SCSI maintainers to resolve this issue outside
of the main kernel tree.  We'll merge the patch once the SCSI layer's
handling of the MODE10 conversion is working for us.

Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] ARM: 2803/1: OMAP update 11/11: Add cpufreq support

Patch from Tony Lindgren

This patch adds minimal cpufreq support for OMAP
taking advantage of the clock framework.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: 2805/1: OMAP update 10/11: Update H2 defconfig

Patch from Tony Lindgren

This patch updates H2 defconfig.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: 2804/1: OMAP update 9/11: Update OMAP arch files

Patch from Tony Lindgren

This patch by various OMAP developers syncs the OMAP
specific arch files with the linux-omap tree.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: 2802/1: OMAP update 8/11: Update OMAP arch files

Patch from Tony Lindgren

This patch by various OMAP developers syncs the OMAP
specific arch files with the linux-omap tree.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: 2812/1: OMAP update 7c/11: Move arch-omap to plat-omap

Patch from Tony Lindgren

This patch move common OMAP code from arch-omap to plat-omap
directory.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: 2809/1: OMAP update 7b/11: Move arch-omap to plat-omap

Patch from Tony Lindgren

This patch move common OMAP code from arch-omap to plat-omap
directory.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: 2807/1: OMAP update 7a/11: Move arch-omap to plat-omap

Patch from Tony Lindgren

This patch move common OMAP code from arch-omap to plat-omap
directory.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: 2801/1: OMAP update 6/11: Split OMAP1 common code into id, io and serial

Patch from Tony Lindgren

This patch by Juha Yrjölä and other OMAP developers splits
OMAP1 specific common code into OMAP1 id, io, and serial
code in mach-omap1 directory.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: 2806/1: OMAP update 5/11: Move board files into mach-omap1 directory

Patch from Tony Lindgren

This patch by Paul Mundt and other OMAP developers
moves OMAP1 board files into mach-omap1 directory.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: 2799/1: OMAP update 4/11: Move OMAP1 LED code into mach-omap1 directory

Patch from Tony Lindgren

This patch by Paul Mundt and other OMAP developers
moves OMAP1 specific LED code into mach-omap1 directory.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: 2800/1: OMAP update 3/11: Move OMAP1 core code into mach-omap1 directory

Patch from Tony Lindgren

This patch by Paul Mundt and other OMAP developers
moves OMAP1 specific IRQ, time, and FPGA code into
mach-omap1 directory.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: 2798/1: OMAP update 2/11: Change ARM Kconfig to support omap1 and omap2

Patch from Tony Lindgren

This patch by Paul Mundt and other OMAP developers modifies
ARM specific Kconfig to allow sharing code between OMAP1 and
OMAP2 architectures.
In order to share code between OMAP1 and OMAP2, all OMAP1
specific code is moved into mach-omap1 directory in the
following patch. A new mach-omap2 directory will be added
later on.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: 2797/1: OMAP update 1/11: Update include files

Patch from Tony Lindgren

This patch by various OMAP developers syncs the OMAP
specific include files with the linux-omap tree.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: 2796/1: Fix ARMv5[TEJ] check in MMU initalization

Patch from Deepak Saxena

The code in mm-armv.c checks for the condition (cpu_architecture()<= ARMv5)
in a few places but should be checking for ARMv5TEJ as the MMU is shared
across all v5 variations.

Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: 2795/1: update ixp2000 defconfigs

Patch from Lennert Buytenhek

Update the ixp2000 defconfigs from 2.6.12-git6 to 2.6.13-rc2.

Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: 2793/1: platform serial support for ixp2000

Patch from Lennert Buytenhek

This patch converts the ixp2000 serial port over to a platform
serial device.

Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

drm: fix stupid missing semicolon.

I fixed this in one git tree but that wasn't the one I pushed...

Signed-off-by: Dave Airlie <airlied@linux.ie>

Merge head 'drm-fixes' of /linux/kernel/git/airlied/drm-2.6

Merge head 'drm-3264' of /linux/kernel/git/airlied/drm-2.6

Merge head 'drm-via' of /linux/kernel/git/airlied/drm-2.6

Merge /pub/scm/linux/kernel/git/davem/sparc-2.6

[SCTP]: Use struct list_head for chunk lists, not sk_buff_head.

Signed-off-by: David S. Miller <davem@davemloft.net>

[IPV6]: Fix warning in ip6_mc_msfilter.

Signed-off-by: David S. Miller <davem@davemloft.net>

[IPV4]: fix IPv4 leave-group group matching

        This patch fixes the multicast group matching for
IP_DROP_MEMBERSHIP, similar to the IP_ADD_MEMBERSHIP fix in a prior
patch. Groups are identifiedby <group address,interface> and including
the interface address in the match will fail if a leave-group is done
by address when the join was done by index, or if different addresses
on the same interface are used in the join and leave.

Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[IPV4]: (INCLUDE,empty)/leave-group equivalence for full-state MSF APIs & errno fix

1) Adds (INCLUDE, empty)/leave-group equivalence to the full-state
   multicast source filter APIs (IPv4 and IPv6)

2) Fixes an incorrect errno in the IPv6 leave-group (ENOENT should be
   EADDRNOTAVAIL)

Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[IPV4]: multicast API "join" issues

1) In the full-state API when imsf_numsrc == 0
   errno should be "0", but returns EADDRNOTAVAIL

2) An illegal filter mode change
   errno should be EINVAL, but returns EADDRNOTAVAIL

3) Trying to do an any-source option without IP_ADD_MEMBERSHIP
   errno should be EINVAL, but returns EADDRNOTAVAIL

4) Adds comments for the less obvious error return values

Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[IPV4]: multicast API "join" issues

1) Changes IP_ADD_SOURCE_MEMBERSHIP and MCAST_JOIN_SOURCE_GROUP to ignore
   EADDRINUSE errors on a "courtesy join" -- prior membership or not
   is ok for these.

2) Adds "leave group" equivalence of (INCLUDE, empty) filters in the
   delta-based API. Without this, mixing delta-based API calls that
   end in an (INCLUDE, empty) filter would not allow a subsequent
   regular IP_ADD_MEMBERSHIP. It also frees socket buffer memory that
   isn't needed for both the multicast group record and source filter.

Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[IPV4]: multicast API "join" issues

        This patch corrects a few problems with the IP_ADD_MEMBERSHIP
socket option:

1) The existing code makes an attempt at reference counting joins when
   using the ip_mreqn/imr_ifindex interface. Joining the same group
   on the same socket is an error, whatever the API. This leads to
   unexpected results when mixing ip_mreqn by index with ip_mreqn by
   address, ip_mreq, or other API's. For example, ip_mreq followed by
   ip_mreqn of the same group will "work" while the same two reversed
   will not.
           Fixed to always return EADDRINUSE on a duplicate join and
   removed the (now unused) reference count in ip_mc_socklist.

2) The group-search list in ip_mc_join_group() is comparing a full
   ip_mreqn structure and all of it must match for it to find the
   group. This doesn't correctly match a group that was joined with
   ip_mreq or ip_mreqn with an address (with or without an index). It
   also doesn't match groups that are joined by different addresses on
   the same interface. All of these are the same multicast group,
   which is identified by group address and interface index.
           Fixed the check to correctly match groups so we don't get
   duplicate group entries on the ip_mc_socklist.

3) The old code allocates a multicast address before searching for
   duplicates requiring it to free in various error cases. This
   patch moves the allocate until after the search and
   igmp_max_memberships check, so never a need to allocate, then free
   an entry.

Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[IPV4]: Apply sysctl_icmp_echo_ignore_broadcasts to ICMP_TIMESTAMP as well.

This was the full intention of the original code.

Signed-off-by: David S. Miller <davem@davemloft.net>

[SPARC64]: Support CONFIG_HZ

Signed-off-by: David S. Miller <davem@davemloft.net>

[NET]: Fix sparse warnings

From: Victor Fusco <victor@cetuc.puc-rio.br>

Fix the sparse warning "implicit cast to nocast type"

Signed-off-by: Victor Fusco <victor@cetuc.puc-rio.br>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

[NET]: Transform skb_queue_len() binary tests into skb_queue_empty()

This is part of the grand scheme to eliminate the qlen
member of skb_queue_head, and subsequently remove the
'list' member of sk_buff.

Most users of skb_queue_len() want to know if the queue is
empty or not, and that's trivially done with skb_queue_empty()
which doesn't use the skb_queue_head->qlen member and instead
uses the queue list emptyness as the test.

Signed-off-by: David S. Miller <davem@davemloft.net>

[SPARC64]: Typo in dtlb_backend.S, _PAGE_SZ4M --> _PAGE_SZ4MB

Noticed by Eddie C. Dost

Signed-off-by: David S. Miller <davem@davemloft.net>

[IA64] Fix a typo in arch/ia64/kernel/entry.S

Both 2.4 and 2.6 kernels need this patch for the next binutils.

Signed-off-by: Tony Luck <tony.luck@intel.com>

Auto merge with /home/aegl/GIT/linus

[PATCH] Add MAINTAINERS entry for audit subsystem

I've been asked about this a couple times, and there's no info in
MAINTAINERS file.  Add MAINTAINERS entry for audit subsystem.

Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] device-mapper: dm-raid1: Limit bios to size of mirror region

Set the target's split_io field when building a dm-mirror device so
incoming bios won't span the mirror's internal regions.  Without this,
regions can be accessed while not holding correct locks and data corruption
is possible.

Reported-By: "Zhao Qian" <zhaoqian@aaastor.com>
From: Kevin Corry <kevcorry@us.ibm.com>
Signed-Off-By: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] video doc: one more system where video works with S3

One more system where video works with S3.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] m32r: framebuffer device support

This patch is for supporting Epson s1d13xxx framebuffer device for m32r.  #
Sorry, a little bigger.

The Epson s1d13806 is already supported by 2.6.12 kernel, and its driver is
placed as drivers/video/s1d13xxxfb.c.

For the m32r, a header file include/asm-m32r/s1d13806.h was prepared for
several m32r target platforms.  It was originally generated by an Epson
tool S1D13806CFG.EXE, and modified manually for the m32r platforms.

Signed-off-by: Hayato Fujiwara <fujiwara@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] nfsd4: fix fh_expire_type

After discussion at the recent NFSv4 bake-a-thon, I realized that my
assumption that NFS4_FH_PERSISTENT required filehandles to persist was a
misreading of the spec.  This also fixes an interoperability problem with the
Solaris client.

Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] nfsd4: check lock type against openmode.

We shouldn't be allowing, e.g., write locks on files not open for read.  To
enforce this, we add a pointer from the lock stateid back to the open stateid
it came from, so that the check will continue to be correct even after the
open is upgraded or downgraded.

Signed-off-by: Andy Adamson <andros@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] nfsd4: clean up nfs4_preprocess_seqid_op

As long as we're here, do some miscellaneous cleanup.

Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] nfsd4: clarify close_lru handling

The handling of close_lru in preprocess_stateid_op was a source of some
confusion here recently.  Try to make the logic a little clearer, by renaming
find_openstateowner_id to make its purpose clearer and untangling some
unnecessarily complicated goto's.

Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] nfsd4: renew lease on seqid modifying operations

nfs4_preprocess_seqid_op is called by NFSv4 operations that imply an implicit
renewal of the client lease.

Signed-off-by: Andy Adamson <andros@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] nfsd4: return better error on io incompatible with open mode

from RFC 3530:
"Share reservations are established by OPEN operations and by their
nature are mandatory in that when the OPEN denies READ or WRITE
operations, that denial results in such operations being rejected
with error NFS4ERR_LOCKED."

(Note that share_denied is really only a legal error for OPEN.)

Signed-off-by: Andy Adamson <andros@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] nfsd4: always update stateid on open

An OPEN from the same client/open stateowner requires a stateid update because
of the share/deny access update.

Signed-off-by: Andy Adamson <andros@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] nfsd4: relax new lock seqid check

We're insisting that the lock sequence id field passed in the
open_to_lockowner struct always be zero.  This is probably thanks to the
sentence in rfc3530: "The first request issued for any given lock_owner is
issued with a sequence number of zero."

But there doesn't seem to be any problem with allowing initial sequence
numbers other than zero.  And currently this is causing lock reclaims from the
Linux client to fail.

In the spirit of "be liberal in what you accept, conservative in what you
send", we'll relax the check (and patch the Linux client as well).

Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] nfsd4: seqid comments

Add some comments on the use of so_seqid, in an attempt to avoid some of the
confusion outlined in the previous patch....

Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] nfsd4: fix open_reclaim seqid

The sequence number we store in the sequence id is the last one we received
from the client.  So on the next operation we'll check that the client gives
us the next higher number.

We increment sequence id's at the last moment, in encode, so that we're sure
of knowing the right error return.  (The decision to increment the sequence id
depends on the exact error returned.)

However on the *first* use of a sequence number, if we set the sequence number
to the one received from the client and then let the increment happen on
encode, we'll be left with a sequence number one to high.

For that reason, ENCODE_SEQID_OP_TAIL only increments the sequence id on
*confirmed* stateowners.

This creates a problem for open reclaims, which are confirmed on first use.
Therefore the open reclaim code, as a special exception, *decrements* the
sequence id, cancelling out the undesired increment on encode.  But this
prevents the sequence id from ever being incremented in the case where
multiple reclaims are sent with the same openowner.  Yuch!

We could add another exception to the open reclaim code, decrementing the
sequence id only if this is the first use of the open owner.

But it's simpler by far to modify the meaning of the op_seqid field: instead
of representing the previous value sent by the client, we take op_seqid, after
encoding, to represent the *next* sequence id that we expect from the client.
This eliminates the need for special-case handling of the first use of a
stateowner.

Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] nfsd4: comment indentation

Yeah, it's trivial, but this drives me up the wall....

Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] nfsd4: stop overusing RECLAIM_BAD

A misreading of the spec lead us to convert all errors on open and lock
reclaims to RECLAIM_BAD.  This causes problems--for example, a reboot within
the grace period could lead to reclaims with stale stateid's, and we'd like to
return STALE errors in those cases.

What rfc3530 actually says about RECLAIM_BAD: "The reclaim provided by the
client does not match any of the server's state consistency checks and is
bad." I'm assuming that "state consistency checks" refers to checks for
consistency with the state recorded to stable storage, and that the error
should be reserved for that case.

Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] nfsd4: ERR_GRACE should bump seqid on lock

A GRACE or NOGRACE response to a lock request should also bump the sequence
id.  So we delay the handling of grace period errors till after we've found
the relevant owner.

Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] nfsd4: ERR_GRACE should bump seqid on open

The GRACE and NOGRACE errors should bump the sequence id on open.  So we delay
the handling of these errors until nfsd4_process_open2, at which point we've
set the open owner, so the encode routine will be able to bump the sequence
id.

Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] nfsd4: fix release_lockowner

We oops in list_for_each_entry(), because release_stateowner frees something
on the list we're traversing.

Signed-off-by: Andy Adamson <andros@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] nfsd4: prevent multiple unlinks of recovery directories

Make sure we don't try to delete client recovery directories multiple times;
fixes some spurious error messages.

Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] nfsd4: lookup_one_len takes i_sem

Oops, this lookup_one_len needs the i_sem.

Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] nfsd4: fix sync'ing of recovery directory

We need to fsync the recovery directory after writing to it, but we weren't
doing this correctly.  (For example, we weren't taking the i_sem when calling
->fsync().)

Just reuse the existing nfsd fsync code instead.

Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] nfsd4: reboot recovery fix

We need to remove the recovery directory here too.  (This chunk just got lost
somehow in the process of commuting the reboot recovery patches past the other
patches.)

Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] yenta: don't depend on CardBus

As a follow-up, we can allow the yenta-driver to be limited to PCMCIA
operation.

Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] yenta: no CardBus if IRQ fails

If probing for the correct interrupt fails on yenta bridges, the driver falls
back to polling for interrupt actions.  However, CardBus cards cannot be used
then.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] pcmcia: update MAINTAINERS entry

PCMCIA/CardBus is handled by a team of developers at the specified mailing
list.  Additional developers wanting to help are most welcome.

Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] pcmcia: remove references to pcmcia/version.h

As a follow-up, remove the inclusion of pcmcia/version.h in many files.

Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] pcmcia: remove client services version (fix)

One correction is needed.  Changes are not needed for
drivers/scsi/pcmcia/nsp_cs.c because it uses versioning in the
compatibility part, which is never used in 2.6 kernels.  The only right
thing we could to that compatibility code would be to remove it throughout
the file, but that would be a separate patch.

Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] pcmcia: remove client services version

The Linux PCMCIA code has some data that was apparently used (or meant to be
used) to ensure that only proper client drivers are loaded.  This is now
ensured (to a certain degree) by the fact that the most client drivers are
part of the kernel.  Also, the version information has not been updated
despite major changes in PCMCIA API.  This has made it meaningless.

This patch removes servinfo_t and pcmcia_get_card_services_info.  They are not
used in any userspace utilities such as pcmcia-cs and pcmciautils.
drivers/pcmcia/pcmcia_ioctl.c is adjusted accordingly.

CS_RELEASE and CS_RELEASE_CODE are removed.  include/pcmcia/version.h is empty
now.  It will be removed later, but for now it's left in the tree to avoid
touching all PCMCIA clients.

The only driver that needs to be changed is drivers/scsi/pcmcia/nsp_cs.c,
which uses CS_RELEASE_CODE.

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] pcmcia: reduce client_handle_t usage

Reduce the occurences of "client_handle_t" which is nothing else than a
pointer to struct pcmcia_device by now.

Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] pcmcia: remove client_t usage

Reduce the occurences of "client_handle_t" which is nothing else than a
pointer to struct pcmcia_device by now.

Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] pcmcia: move event handler

Move the "event handler" to struct pcmcia_driver -- the unified event handler
will disappear really soon, but switching it to struct pcmcia_driver in the
meantime allows for better "step-by-step" patches.

Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] pcmcia: deprecate ioctl

Schedule removal of the PCMCIA ioctl (and thus kernel support for the
pcmcia-cs userspace package) for November 2005.

A big "thank you" to Dave Hinds for his great work on supporting PCMCIA in
Linux.  Things are just done differently by now, so the ongoing work to make
PCMCIA behave like any other hotpluggable bus should continue.

Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] pcmcia: fix i82365 request_region double usage

http://www.kernel.org/git/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=f354942cb301fed273f423fb5c4f57bde3efc5b2
converted the check_region() calls in drivers/pcmcia/i82365.c into
request_regions.  Unfortunately this seems to have broken things.

isa_probe() used to call check_region() and then call add_pcic() which would
request_region().

Now isa_probe() calls request_region() and then calls add_pcic() which calls
request_region() again, this fails and add_pcic() returns immediately without
doing all the setup etc.

On the face of it the patch below fixes the problem, by not doing the second
request region in add_pcic().  I think this is preferable to remove the call
in isa_probe() since identify() touches the I/O regions and is called before
add_pcic().

However I haven't fully grokked the meaning of the code which follows the
request_region() in isa_probe(), so I'm not sure that the handling WRT
multiple sockets and multiple bridge chips is correct.  In particular I'm not
convinced that the regions for subsequent sockets and/or bridges will be
requested at all.  I suspect a more thorough reworking by someone who
understands what is going on there might be in order.

I should mention that I'm actually messing about with this on an ARM platform
with wacky memory and i/o mapping offsets etc, it doesn't quite work yet for
other reasons which preclude full testing etc, but I think the problem above
is still present for more normal x86 stuff.

Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] v4l: LGDT3302 read status fix

- Fix bug in lgdt3302_read_status to return correct
  FE_HAS_SIGNAL and FS_HAS_CARRIER status.
- Removed #if LINUX_VERSION_CODE > KERNEL_VERSION(2,6,10).

Signed-off-by: Mac Michaels <wmichaels1@earthlink.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] v4l: add DVB support for DViCO FusionHDTV3 Gold-T

- Correct sync byte for MPEG-2 transport stream packets.
- Add lgdt3302 as dependency of cx88-dvb in Kconfig.
- Add dvb support in v4l for DViCO FusionHDTV3 Gold-T using lgdt3302 frontend.
  This adds support for a different board from the previous (Gold-Q) patch.

Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] v4l: add TerraTec Cinergy 1400 DVB-T

Add support for TerraTec Cinergy 1400 DVB-T.

Signed-off-by: Uli Luckas <luckas@musoft.de>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] v4l: add DVB support for DViCO FusionHDTV3 Gold-Q

Add dvb support in v4l for DViCO FusionHDTV3 Gold-Q using lgdt3302 frontend.

Signed-off-by: Mac Michaels <wmichaels1@earthlink.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] v4l: cx88 hue offset fix

Changed hue offset to 128 to correct behavior in cx88 cards.  Previously,
setting 0% or 100% hue was required to avoid blue/green people on screen.
Now, 50% Hue means no offset, just like bt878 stuff.

Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] v4l: cx88 update

- Add support for ADS Tech Instant TV DVB-T PCI.
- Remove obsoleted config options.
- Fix DViCO Board names
- Remove CABLE type setting from DViCO FusionHDTV3 Gold-T.
- Fix compilation with gcc4.0.
- V4L2_TUNER_CAP_LOW implemented according with V4L2 API for Radio.
- radio range is now defined on tuner-core.c. Cleaning up.
- Fix a bug on frequency report for cx88 based cards.
- Added support for changing radio mode stereo/mono.
- Add remove for MSI TV@nywhere.

Signed-off-by: Jorik Jonker <jorik@dnd.utwente.nl>.
Signed-off-by: Didier Caillaud <mailing.cld@free.fr>
Signed-off-by: Benoit Laniel <benoit.laniel@gmail.com>.
Signed-off-by: Nickolay V Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] fix for Documentation/dvb/bt8xx.txt?=

*   /usr/src/linux-2.6.12/Documentation/dvb/bt8xx.txt

  almost completely remade the text file with the following focuses:
  useful infos for beginners: how to load modules manually and
  automatically developers infos are reduced to a minimum as module loading
  works automatic in kernel >= 2.6.12 by loading modules bttv and dvb-bt8xx
  I completely erased the out of date TwinHan part dealing with additional
  parameters, debug parameters, and overriding autodetection Further up to
  date information about TwinHan + clones can be found in
  /Documentation/dvb/ci.txt

Signed-off-by: Uwe Bugla <uwe.bugla@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] dvb: usb: README update

Updated the readme file to point to the DVB USB wikipage to find out which
firmware necessary, + minor updates.

Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>