Kevin Tian [Tue, 30 Aug 2011 10:56:17 +0000 (13:56 +0300)]
KVM: APIC: avoid instruction emulation for EOI writes
Instruction emulation for EOI writes can be skipped, since sane
guest simply uses MOV instead of string operations. This is a nice
improvement when guest doesn't support x2apic or hyper-V EOI
support.
a single VM bandwidth is observed with ~8% bandwidth improvement
(7.4Gbps->8Gbps), by saving ~5% cycles from EOI emulation.
Signed-off-by: Kevin Tian <kevin.tian@intel.com>
<Based on earlier work from>:
Signed-off-by: Eddie Dong <eddie.dong@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Nadav Har'El [Tue, 2 Aug 2011 12:55:23 +0000 (15:55 +0300)]
KVM: SVM: Fix TSC MSR read in nested SVM
When the TSC MSR is read by an L2 guest (when L1 allowed this MSR to be
read without exit), we need to return L2's notion of the TSC, not L1's.
The current code incorrectly returned L1 TSC, because svm_get_msr() was also
used in x86.c where this was assumed, but now that these places call the new
svm_read_l1_tsc(), the MSR read can be fixed.
Signed-off-by: Nadav Har'El <nyh@il.ibm.com>
Tested-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Nadav Har'El [Tue, 2 Aug 2011 12:54:52 +0000 (15:54 +0300)]
KVM: nVMX: Fix nested VMX TSC emulation
This patch fixes two corner cases in nested (L2) handling of TSC-related
issues:
1. Somewhat suprisingly, according to the Intel spec, if L1 allows WRMSR to
the TSC MSR without an exit, then this should set L1's TSC value itself - not
offset by vmcs12.TSC_OFFSET (like was wrongly done in the previous code).
2. Allow L1 to disable the TSC_OFFSETING control, and then correctly ignore
the vmcs12.TSC_OFFSET.
Signed-off-by: Nadav Har'El <nyh@il.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Nadav Har'El [Tue, 2 Aug 2011 12:54:20 +0000 (15:54 +0300)]
KVM: L1 TSC handling
KVM assumed in several places that reading the TSC MSR returns the value for
L1. This is incorrect, because when L2 is running, the correct TSC read exit
emulation is to return L2's value.
We therefore add a new x86_ops function, read_l1_tsc, to use in places that
specifically need to read the L1 TSC, NOT the TSC of the current level of
guest.
Note that one change, of one line in kvm_arch_vcpu_load, is made redundant
by a different patch sent by Zachary Amsden (and not yet applied):
kvm_arch_vcpu_load() should not read the guest TSC, and if it didn't, of
course we didn't have to change the call of kvm_get_msr() to read_l1_tsc().
[avi: moved callback to kvm_x86_ops tsc block]
Signed-off-by: Nadav Har'El <nyh@il.ibm.com>
Acked-by: Zachary Amsdem <zamsden@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Sasha Levin [Tue, 9 Aug 2011 11:28:35 +0000 (14:28 +0300)]
KVM: nVMX: Document 'nested' parameter
Add documentation of the new 'nested' parameter to
'Documentation/kernel-parameters.txt'.
Cc: Avi Kivity <avi@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Nadav Har'El <nyh@il.ibm.com>
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Yang, Wei Y [Tue, 9 Aug 2011 10:14:01 +0000 (18:14 +0800)]
KVM: MMU: Fix SMEP failure during fetch
This patch fix kvm-unit-tests hanging and incorrect PT_ACCESSED_MASK
bit set in the case of SMEP fault. The code updated 'eperm' after
the variable was checked.
Signed-off-by: Yang, Wei <wei.y.yang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Avi Kivity [Thu, 28 Jul 2011 08:36:17 +0000 (11:36 +0300)]
KVM: MMU: Do not unconditionally read PDPTE from guest memory
Architecturally, PDPTEs are cached in the PDPTRs when CR3 is reloaded.
On SVM, it is not possible to implement this, but on VMX this is possible
and was indeed implemented until nested SVM changed this to unconditionally
read PDPTEs dynamically. This has noticable impact when running PAE guests.
Fix by changing the MMU to read PDPTRs from the cache, falling back to
reading from memory for the nested MMU.
Signed-off-by: Avi Kivity <avi@redhat.com>
Tested-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Julia Lawall [Tue, 2 Aug 2011 10:34:57 +0000 (12:34 +0200)]
KVM: VMX: trivial: use BUG_ON
Use BUG_ON(x) rather than if(x) BUG();
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ identifier x; @@
-if (x) BUG();
+BUG_ON(x);
@@ identifier x; @@
-if (!x) BUG();
+BUG_ON(!x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Marcelo Tosatti [Fri, 29 Jul 2011 22:44:21 +0000 (19:44 -0300)]
KVM: x86: report valid microcode update ID
Windows Server 2008 SP2 checked build with smp > 1 BSOD's during
boot due to lack of microcode update:
*** Assertion failed: The system BIOS on this machine does not properly
support the processor. The system BIOS did not load any microcode update.
A BIOS containing the latest microcode update is needed for system reliability.
(CurrentUpdateRevision != 0)
*** Source File: d:\longhorn\base\hals\update\intelupd\update.c, line 440
Report a non-zero microcode update signature to make it happy.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Takuya Yoshikawa [Sat, 30 Jul 2011 09:03:34 +0000 (18:03 +0900)]
KVM: x86 emulator: Make x86_decode_insn() return proper macros
Return EMULATION_OK/FAILED consistently. Also treat instruction fetch
errors, not restricted to X86EMUL_UNHANDLEABLE, as EMULATION_FAILED;
although this cannot happen in practice, the current logic will continue
the emulation even if the decoder fails to fetch the instruction.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
Takuya Yoshikawa [Sat, 30 Jul 2011 09:02:29 +0000 (18:02 +0900)]
KVM: x86 emulator: Let compiler know insn_fetch() rarely fails
Fetching the instruction which was to be executed by the guest cannot
fail normally. So compiler should always predict that it will succeed.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
Takuya Yoshikawa [Sat, 30 Jul 2011 09:01:26 +0000 (18:01 +0900)]
KVM: x86 emulator: Drop _size argument from insn_fetch()
_type is enough to know the size.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
Takuya Yoshikawa [Sat, 30 Jul 2011 09:00:17 +0000 (18:00 +0900)]
KVM: x86 emulator: Use ctxt->_eip directly in do_insn_fetch_byte()
Instead of passing ctxt->_eip from insn_fetch() call sites, get it from
ctxt in do_insn_fetch_byte(). This is done by replacing the argument
_eip of insn_fetch() with _ctxt, which should be better than letting the
macro use ctxt silently in its body.
Though this changes the place where ctxt->_eip is incremented from
insn_fetch() to do_insn_fetch_byte(), this does not have any real
effect.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
Sasha Levin [Wed, 27 Jul 2011 13:00:48 +0000 (16:00 +0300)]
KVM: Intelligent device lookup on I/O bus
Currently the method of dealing with an IO operation on a bus (PIO/MMIO)
is to call the read or write callback for each device registered
on the bus until we find a device which handles it.
Since the number of devices on a bus can be significant due to ioeventfds
and coalesced MMIO zones, this leads to a lot of overhead on each IO
operation.
Instead of registering devices, we now register ranges which points to
a device. Lookup is done using an efficient bsearch instead of a linear
search.
Performance test was conducted by comparing exit count per second with
200 ioeventfds created on one byte and the guest is trying to access a
different byte continuously (triggering usermode exits).
Before the patch the guest has achieved 259k exits per second, after the
patch the guest does 274k exits per second.
Cc: Avi Kivity <avi@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Stefan Hajnoczi [Fri, 22 Jul 2011 11:46:53 +0000 (12:46 +0100)]
KVM: Use __print_symbolic() for vmexit tracepoints
The vmexit tracepoints format the exit_reason to make it human-readable.
Since the exit_reason depends on the instruction set (vmx or svm),
formatting is handled with ftrace_print_symbols_seq() by referring to
the appropriate exit reason table.
However, the ftrace_print_symbols_seq() function is not meant to be used
directly in tracepoints since it does not export the formatting table
which userspace tools like trace-cmd and perf use to format traces.
In practice perf dies when formatting vmexit-related events and
trace-cmd falls back to printing the numeric value (with extra
formatting code in the kvm plugin to paper over this limitation). Other
userspace consumers of vmexit-related tracepoints would be in similar
trouble.
To avoid significant changes to the kvm_exit tracepoint, this patch
moves the vmx and svm exit reason tables into arch/x86/kvm/trace.h and
selects the right table with __print_symbolic() depending on the
instruction set. Note that __print_symbolic() is designed for exporting
the formatting table to userspace and allows trace-cmd and perf to work.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Stefan Hajnoczi [Fri, 22 Jul 2011 11:46:52 +0000 (12:46 +0100)]
KVM: Record instruction set in all vmexit tracepoints
The kvm_exit tracepoint recently added the isa argument to aid decoding
exit_reason. The semantics of exit_reason depend on the instruction set
(vmx or svm) and the isa argument allows traces to be analyzed on other
machines.
Add the isa argument to kvm_nested_vmexit and kvm_nested_vmexit_inject
so these tracepoints can also be self-describing.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Mike Waychison [Sat, 23 Jul 2011 07:31:45 +0000 (00:31 -0700)]
KVM: Really fix HV_X64_MSR_APIC_ASSIST_PAGE
Commit
0945d4b228 tried to fix the get_msr path for the
HV_X64_MSR_APIC_ASSIST_PAGE msr, but was poorly tested. We should be
returning 0 if the read succeeded, and passing the value back to the
caller via the pdata out argument, not returning the value directly.
Signed-off-by: Mike Waychison <mikew@google.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Mike Waychison [Thu, 21 Jul 2011 22:38:10 +0000 (15:38 -0700)]
KVM: x86: get_msr support for HV_X64_MSR_APIC_ASSIST_PAGE
"get" support for the HV_X64_MSR_APIC_ASSIST_PAGE msr was missing, even
though it is explicitly enumerated as something the vmm should save in
msrs_to_save and reported to userland via the KVM_GET_MSR_INDEX_LIST
ioctl.
Add "get" support for HV_X64_MSR_APIC_ASSIST_PAGE. We simply return the
guest visible value of this register, which seems to be correct as a set
on the register is validated for us already.
Signed-off-by: Mike Waychison <mikew@google.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Sasha Levin [Wed, 20 Jul 2011 17:59:00 +0000 (20:59 +0300)]
KVM: Make coalesced mmio use a device per zone
This patch changes coalesced mmio to create one mmio device per
zone instead of handling all zones in one device.
Doing so enables us to take advantage of existing locking and prevents
a race condition between coalesced mmio registration/unregistration
and lookups.
Suggested-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Sasha Levin [Mon, 18 Jul 2011 14:17:15 +0000 (17:17 +0300)]
KVM: x86: Raise the hard VCPU count limit
The patch raises the hard limit of VCPU count to 254.
This will allow developers to easily work on scalability
and will allow users to test high VCPU setups easily without
patching the kernel.
To prevent possible issues with current setups, KVM_CAP_NR_VCPUS
now returns the recommended VCPU limit (which is still 64) - this
should be a safe value for everybody, while a new KVM_CAP_MAX_VCPUS
returns the hard limit which is now 254.
Cc: Avi Kivity <avi@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Pekka Enberg <penberg@kernel.org>
Suggested-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Sasha Levin [Mon, 18 Jul 2011 14:17:14 +0000 (17:17 +0300)]
KVM: MMIO: Lock coalesced device when checking for available entry
Move the check whether there are available entries to within the spinlock.
This allows working with larger amount of VCPUs and reduces premature
exits when using a large number of VCPUs.
Cc: Avi Kivity <avi@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Xiao Guangrong [Wed, 13 Jul 2011 06:32:31 +0000 (14:32 +0800)]
KVM: x86: cleanup the code of read/write emulation
Using the read/write operation to remove the same code
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Xiao Guangrong [Wed, 13 Jul 2011 06:31:50 +0000 (14:31 +0800)]
KVM: x86: abstract the operation for read/write emulation
The operations of read emulation and write emulation are very similar, so we
can abstract the operation of them, in larter patch, it is used to cleanup the
same code
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Xiao Guangrong [Wed, 13 Jul 2011 06:31:08 +0000 (14:31 +0800)]
KVM: x86: fix broken read emulation spans a page boundary
If the range spans a page boundary, the mmio access can be broke, fix it as
write emulation.
And we already get the guest physical address, so use it to read guest data
directly to avoid walking guest page table again
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Avi Kivity [Tue, 13 Sep 2011 07:45:38 +0000 (10:45 +0300)]
KVM: x86 emulator: fix Src2CL decode
Src2CL decode (used for double width shifts) erronously decodes only bit 3
of %rcx, instead of bits 7:0.
Fix by decoding %cl in its entirety.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Zhao Jin [Mon, 19 Sep 2011 04:19:51 +0000 (12:19 +0800)]
KVM: MMU: fix incorrect return of spte
__update_clear_spte_slow should return original spte while the
current code returns low half of original spte combined with high
half of new spte.
Signed-off-by: Zhao Jin <cronozhj@gmail.com>
Reviewed-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Linus Torvalds [Fri, 23 Sep 2011 23:53:16 +0000 (16:53 -0700)]
Merge branch 'spi/merge' of git://git.secretlab.ca/git/linux-2.6
* 'spi/merge' of git://git.secretlab.ca/git/linux-2.6:
spi: Fix WARN when removing spi-fsl-spi module
spi/imx: Fix spi-imx when the hardware SPI chipselects are used
Jeff Harris [Fri, 23 Sep 2011 15:49:36 +0000 (11:49 -0400)]
spi: Fix WARN when removing spi-fsl-spi module
If CPM mode is not used, the fsl_dummy_rx variable is never allocated. When
the cleanup attempts to free it, the reference count is zero and a WARN is
generated. The same CPM mode check used in the initialize is applied to the
free as well.
Tested on 2.6.33 with the previous spi_mpc8xxx driver. The renamed
spi-fsl-spi driver looks to have the same problem.
Signed-off-by: Jeff Harris <jeff_harris@kentrox.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Randy Dunlap [Fri, 23 Sep 2011 22:40:50 +0000 (15:40 -0700)]
scsi: fix qla2xxx printk format warning
sector_t can be different types, so cast it to its largest possible
type.
drivers/scsi/qla2xxx/qla_isr.c:1509:5: warning: format '%lx' expects type 'long unsigned int', but argument 5 has type 'sector_t'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Fri, 23 Sep 2011 22:43:54 +0000 (15:43 -0700)]
scsi: SCSI_ISCI needs to select SCSI_SAS_HOST_SMP, fixes build error
SCSI_ISCI needs to select SCSI_SAS_HOST_SMP to ensure that all
needed symbols are available to it.
Fixes this build error:
ERROR: "try_test_sas_gpio_gp_bit" [drivers/scsi/isci/isci.ko] undefined!
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 23 Sep 2011 22:17:02 +0000 (15:17 -0700)]
Merge branch 'perf-tools-for-linus' of git://github.com/acmel/linux
* 'perf-tools-for-linus' of git://github.com/acmel/linux:
perf python: Add missing perf_event__parse_sample 'swapped' parm
Linus Torvalds [Fri, 23 Sep 2011 20:59:37 +0000 (13:59 -0700)]
Merge branch 'perf-tools-for-linus' of git://github.com/acmel/linux
* 'perf-tools-for-linus' of git://github.com/acmel/linux:
perf tools: Add support for disabling -Werror via WERROR=0
perf top: Fix userspace sample addr map offset
perf symbols: Fix issue with binaries using 16-bytes buildids (v2)
perf tool: Fix endianness handling of u32 data in samples
perf sort: Fix symbol sort output by separating unresolved samples by type
perf symbols: Synthesize anonymous mmap events
perf record: Create events initially disabled and enable after init
perf symbols: Add some heuristics for choosing the best duplicate symbol
perf symbols: Preserve symbol scope when parsing /proc/kallsyms
perf symbols: /proc/kallsyms does not sort module symbols
perf symbols: Fix ppc64 SEGV in dso__load_sym with debuginfo files
perf probe: Fix regression of variable finder
Linus Torvalds [Fri, 23 Sep 2011 19:05:53 +0000 (12:05 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: fix DDIA enable on some rs690 systems
Revert "drm/radeon/kms: fix typo in r100_blit_copy"
Linus Torvalds [Fri, 23 Sep 2011 19:04:32 +0000 (12:04 -0700)]
Merge branch 'for-linus' of git://github.com/tiwai/sound
* 'for-linus' of git://github.com/tiwai/sound:
ALSA: usb-audio - clear chip->probing on error exit
ALSA: fm801: Gracefully handle failure of tuner auto-detect
ALSA: fm801: Fix double free in case of error in tuner detection
ASoC: Ensure we generate a driver name
ASoC: Remove bitrotted wm8962_resume()
ASoC: bf5xx-
ad73311: Fix prototype for bf5xx_probe
Arnaldo Carvalho de Melo [Fri, 23 Sep 2011 18:38:53 +0000 (15:38 -0300)]
perf python: Add missing perf_event__parse_sample 'swapped' parm
Problem introduced in
936be50, that missed one perf_event__parse_sample
user, the python binding.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-ja4phms9618ggi657plyuch2@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Darren Hart [Thu, 8 Sep 2011 20:42:39 +0000 (13:42 -0700)]
perf tools: Add support for disabling -Werror via WERROR=0
GCC often introduces new warnings with lots of false positives -
breaking -Werror builds. WERROR=0 allows one to build perf without much
fuss - while still encouraging people to send patches to avoid the fuss
of having to type WERROR=0.
Bisecting back to commits that produce a (mostly harmless) warning on
some compilers is more difficult. With WERROR=0 one could bisect without
worrying about harmless warnings.
Cc: Ingo Molnar <mingo@elte.hu>
Link: http://lkml.kernel.org/r/eac06c7cc4920e5d4830417d466161fb26c7359c.1315514559.git.dvhart@linux.intel.com
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Arnaldo Carvalho de Melo [Wed, 14 Sep 2011 18:54:30 +0000 (15:54 -0300)]
perf top: Fix userspace sample addr map offset
The 'perf top' tool came from the kernel where we had each DSO (vmlinux,
modules) loaded just once at a time.
But userspace may have DSOs loaded in multiple addresses (shared
libraries), requiring that we use the just resolved map instead of the
first one found.
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-ag53wz0yllpgers0n2w7hchp@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Stephane Eranian [Fri, 22 Oct 2010 15:25:01 +0000 (17:25 +0200)]
perf symbols: Fix issue with binaries using 16-bytes buildids (v2)
Buildid can vary in size. According to the man page of ld, buildid can
be 160 bits (sha1) or 128 bits (md5, uuid). Perf assumes buildid size of
20 bytes (160 bits) regardless. When dealing with md5 buildids, it would
thus read more than needed and that would cause mismatches and samples
without symbols.
This patch fixes this by taking into account the actual buildid size as
encoded int he section header. The leftover bytes are also cleared.
This second version fixes a minor issue with the memset() base position.
Cc: David S. Miller <davem@davemloft.net>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@gmail.com>
Link: http://lkml.kernel.org/r/4cc1af3c.8ee7d80a.5a28.ffff868e@mx.google.com
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
David Ahern [Tue, 6 Sep 2011 15:12:26 +0000 (09:12 -0600)]
perf tool: Fix endianness handling of u32 data in samples
Currently, analyzing PPC data files on x86 the cpu field is always 0 and
the tid and pid are backwards. For example, analyzing a PPC file on PPC
the pid/tid fields show:
rsyslogd 1210/1212
and analyzing the same PPC file using an x86 perf binary shows:
rsyslogd 1212/1210
The problem is that the swap_op method for samples is
perf_event__all64_swap which assumes all elements in the sample_data
struct are u64s. cpu, tid and pid are u32s and need to be handled
individually. Given that the swap is done before the sample is parsed,
the simplest solution is to undo the 64-bit swap of those elements when
the sample is parsed and do the proper swap.
The RAW data field is generic and perf cannot have programmatic knowledge
of how to treat that data. Instead a warning is given to the user.
Thanks to Anton Blanchard for providing a data file for a mult-CPU
PPC system so I could verify the fix for the CPU fields.
v3 -> v4:
- fixed use of WARN_ONCE
v2 -> v3:
- used WARN_ONCE for message regarding raw data
- removed struct wrapper around union
- fixed whitespace issues
v1 -> v2:
- added a union for undoing the byte-swap on u64 and redoing swap on
u32's to address compiler errors (see git commit
65014ab3)
Cc: Anton Blanchard <anton@samba.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1315321946-16993-1-git-send-email-dsahern@gmail.com
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Anton Blanchard [Wed, 31 Aug 2011 01:51:45 +0000 (11:51 +1000)]
perf sort: Fix symbol sort output by separating unresolved samples by type
I took a profile that suggested 60% of total CPU time was in the
hypervisor:
...
60.20% [H] 0x33d43c
4.43% [k] ._spin_lock_irqsave
1.07% [k] ._spin_lock
Using perf stat to get the user/kernel/hypervisor breakdown contradicted
this.
The problem is we merge all unresolved samples into the one unknown
bucket. If add a comparison by sample type to sort__sym_cmp we get the
real picture:
...
57.11% [.] 0x80fbf63c
4.43% [k] ._spin_lock_irqsave
1.07% [k] ._spin_lock
0.65% [H] 0x33d43c
So it was almost all userspace, not hypervisor as the initial profile
suggested.
I found another issue while adding this. Symbol sorting sometimes shows
multiple entries for the unknown bucket:
...
16.65% [.] 0x6cd3a8
7.25% [.] 0x422460
5.37% [.] yylex
4.79% [.] malloc
4.78% [.] _int_malloc
4.03% [.] _int_free
3.95% [.] hash_source_code_string
2.82% [.] 0x532908
2.64% [.] 0x36b538
0.94% [H] 0x8000000000e132a4
0.82% [H] 0x800000000000e8b0
This happens because we aren't consistent with our sorting. On
one hand we check to see if both symbols match and for two unresolved
samples sym is NULL so we match:
if (left->ms.sym == right->ms.sym)
return 0;
On the other hand we use sample IP for unresolved samples when
comparing against a symbol:
ip_l = left->ms.sym ? left->ms.sym->start : left->ip;
ip_r = right->ms.sym ? right->ms.sym->start : right->ip;
This means unresolved samples end up spread across the rbtree and we
can't merge them all.
If we use cmp_null all unresolved samples will end up in the one bucket
and the output makes more sense:
...
39.12% [.] 0x36b538
5.37% [.] yylex
4.79% [.] malloc
4.78% [.] _int_malloc
4.03% [.] _int_free
3.95% [.] hash_source_code_string
2.26% [H] 0x800000000000e8b0
Acked-by: Eric B Munson <emunson@mgebm.net>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ian Munsie <imunsie@au1.ibm.com>
Link: http://lkml.kernel.org/r/20110831115145.4f598ab2@kryten
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Anton Blanchard [Mon, 29 Aug 2011 23:15:06 +0000 (09:15 +1000)]
perf symbols: Synthesize anonymous mmap events
perf_event__synthesize_mmap_events does not create anonymous mmap events
even though the kernel does. As a result an already running application
with dynamically created code will not get profiled - all samples end up
in the unknown bucket.
This patch skips any entries with '[' in the name to avoid adding events
for special regions (eg the vsyscall page). All other executable mmaps
are assumed to be anonymous and an event is synthesized.
Acked-by: Pekka Enberg <penberg@kernel.org>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Link: http://lkml.kernel.org/r/20110830091506.60b51fe8@kryten
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
David Ahern [Thu, 25 Aug 2011 16:17:55 +0000 (10:17 -0600)]
perf record: Create events initially disabled and enable after init
perf-record currently creates events enabled. When doing a system wide
collection (-a arg) this causes data collection for perf's
initialization activities -- eg., perf_event__synthesize_threads().
For some events (e.g., context switch S/W event or tracepoints like
syscalls) perf's initialization causes a lot of events to be captured
frequently generating "Check IO/CPU overload!" warnings on larger
systems (e.g., 2 socket, quad core, hyperthreading).
perf's initialization phase can be skipped by creating events
disabled and then enabling them once the initialization is done.
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1314289075-14706-1-git-send-email-dsahern@gmail.com
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Anton Blanchard [Wed, 24 Aug 2011 06:40:17 +0000 (16:40 +1000)]
perf symbols: Add some heuristics for choosing the best duplicate symbol
Try and pick the best symbol based on a few heuristics:
- Prefer a non weak symbol over a weak one
- Prefer a global symbol over a non global one
- Prefer a symbol with less underscores (idea taken from kallsyms.c)
- If all else fails, choose the symbol with the longest name
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110824065243.161953371@samba.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Anton Blanchard [Wed, 24 Aug 2011 06:40:16 +0000 (16:40 +1000)]
perf symbols: Preserve symbol scope when parsing /proc/kallsyms
kallsyms__parse capitalises the symbol type, so every symbol is marked
global. Remove this and fix symbol_type__is_a to handle both local and
global symbols.
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110824065243.077125989@samba.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Anton Blanchard [Wed, 24 Aug 2011 06:40:15 +0000 (16:40 +1000)]
perf symbols: /proc/kallsyms does not sort module symbols
kallsyms__parse assumes that /proc/kallsyms is sorted and sets the end
of the previous symbol to the start of the current one.
Unfortunately module symbols are not sorted, eg:
ffffffffa0081f30 t e1000_clean_rx_irq [e1000e]
ffffffffa00817a0 t e1000_alloc_rx_buffers [e1000e]
Some symbols end up with a negative length and others have a length
larger than they should. This results in confusing perf output.
We already have a function to fixup the end of zero length symbols so
use that instead.
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110824065242.969681349@samba.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Anton Blanchard [Wed, 24 Aug 2011 06:40:14 +0000 (16:40 +1000)]
perf symbols: Fix ppc64 SEGV in dso__load_sym with debuginfo files
64bit PowerPC debuginfo files have an empty function descriptor section.
I hit a SEGV when perf tried to use this section for symbol resolution.
To fix this we need to check the section is valid and we can do this by
checking for type SHT_PROGBITS.
Cc: <stable@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Eric B Munson <emunson@mgebm.net>
Link: http://lkml.kernel.org/r/20110824065242.895239970@samba.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Masami Hiramatsu [Sat, 20 Aug 2011 05:39:23 +0000 (14:39 +0900)]
perf probe: Fix regression of variable finder
Fix to call convert_variable() if previous call does not fail.
To call convert_variable, it ensures "ret" is 0. However, since
"ret" has the return value of synthesize_perf_probe_arg() which
always returns positive value if it succeeded, perf probe doesn't
call convert_variable(). This will cause a SEGV when we add an
event with arguments.
This has to be fixed as it ensures "ret" is greater than 0
(or not negative).
This regression has been introduced by my previous patch,
f182e3e1.
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: yrl.pp-manager.tt@hitachi.com
Link: http://lkml.kernel.org/r/20110820053922.3286.65805.stgit@fedora15
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Takashi Iwai [Fri, 23 Sep 2011 13:26:37 +0000 (15:26 +0200)]
Merge branch 'fix/asoc' into for-linus
Thomas Pfaff [Thu, 22 Sep 2011 16:26:06 +0000 (18:26 +0200)]
ALSA: usb-audio - clear chip->probing on error exit
The Terratec Aureon 5.1 USB sound card support is broken since kernel
2.6.39.
2.6.39 introduced power management support for USB sound cards that added
a probing flag in struct snd_usb_audio.
During the probe of the card it gives following error message :
usb 7-2: new full speed USB device number 2 using uhci_hcd
cannot find UAC_HEADER
snd-usb-audio: probe of 7-2:1.3 failed with error -5
input: USB Audio as
/devices/pci0000:00/0000:00:1d.1/usb7/7-2/7-2:1.3/input/input6
generic-usb 0003:0CCD:0028.0001: input: USB HID v1.00 Device [USB Audio]
on usb-0000:00:1d.1-2/input3
I can not comment about that "cannot find UAC_HEADER" error, but until
2.6.38 the card worked anyway.
With 2.6.39 chip->probing remains 1 on error exit, and any later ioctl
stops in snd_usb_autoresume with -ENODEV.
Signed-off-by: Thomas Pfaff <tpfaff@gmx.net>
Cc: <stable@kernel.org> [2.6.39+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Alex Deucher [Thu, 22 Sep 2011 14:47:23 +0000 (10:47 -0400)]
drm/radeon/kms: fix DDIA enable on some rs690 systems
DVOOutputControl checks the value of of bios scratch reg 3
on some tables and assumes the encoder is already enabled
if the DFP2_ACTIVE bit is set. Clear that bit so the table
sets the DDIA enable bit properly.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 23 Sep 2011 13:00:54 +0000 (14:00 +0100)]
Revert "drm/radeon/kms: fix typo in r100_blit_copy"
This reverts commit
18b4fada275dd2b6dd9db904ddf70fe39e272222.
This code was correct, apologies to anyone who noticed things broke.
revert contents are different due to another commit in between.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Fri, 23 Sep 2011 02:57:27 +0000 (19:57 -0700)]
Merge branch 'for-linus' of git://git.selinuxproject.org/~jmorris/linux-security
* 'for-linus' of git://git.selinuxproject.org/~jmorris/linux-security:
TPM: Zero buffer after copying to userspace
TPM: Call tpm_transmit with correct size
TPM: tpm_nsc: Fix a double free of pdev in cleanup_nsc
TPM: TCG_ATMEL should depend on HAS_IOPORT
Peter Huewe [Thu, 15 Sep 2011 17:47:42 +0000 (14:47 -0300)]
TPM: Zero buffer after copying to userspace
Since the buffer might contain security related data it might be a good idea to
zero the buffer after we have copied it to userspace.
This got assigned CVE-2011-1162.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: James Morris <jmorris@namei.org>
Peter Huewe [Thu, 15 Sep 2011 17:37:43 +0000 (14:37 -0300)]
TPM: Call tpm_transmit with correct size
This patch changes the call of tpm_transmit by supplying the size of the
userspace buffer instead of TPM_BUFSIZE.
This got assigned CVE-2011-1161.
[The first hunk didn't make sense given one could expect
way less data than TPM_BUFSIZE, so added tpm_transmit boundary
check over bufsiz instead
The last parameter of tpm_transmit() reflects the amount
of data expected from the device, and not the buffer size
being supplied to it. It isn't ideal to parse it directly,
so we just set it to the maximum the input buffer can handle
and let the userspace API to do such job.]
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: James Morris <jmorris@namei.org>
Axel Lin [Wed, 3 Aug 2011 23:58:07 +0000 (07:58 +0800)]
TPM: tpm_nsc: Fix a double free of pdev in cleanup_nsc
platform_device_unregister() will release all resources
and remove it from the subsystem, then drop reference count by
calling platform_device_put().
We should not call kfree(pdev) after platform_device_unregister(pdev).
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Geert Uytterhoeven [Mon, 8 Aug 2011 11:08:19 +0000 (13:08 +0200)]
TPM: TCG_ATMEL should depend on HAS_IOPORT
On m68k, I get:
drivers/char/tpm/tpm_atmel.h: In function ‘atmel_get_base_addr’:
drivers/char/tpm/tpm_atmel.h:129: error: implicit declaration of function ‘ioport_map’
drivers/char/tpm/tpm_atmel.h:129: warning: return makes pointer from integer without a cast
The code in tpm_atmel.h supports PPC64 (using the device tree and ioremap())
and "anything else" (using ioport_map()). However, ioportmap() is only
available on platforms that set HAS_IOPORT.
Although PC64 seems to have HAS_IOPORT, a "depends on HAS_IOPORT" should work,
but I think it's better to expose the special PPC64 handling explicit using
"depends on PPC64 || HAS_IOPORT".
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
David Rientjes [Thu, 22 Sep 2011 21:11:38 +0000 (14:11 -0700)]
thp: fix khugepaged defrag tunable documentation
Commit
e27e6151b154 ("mm/thp: use conventional format for boolean
attributes") changed
/sys/kernel/mm/transparent_hugepage/khugepaged/defrag
to be tuned by using 1 (enabled) or 0 (disabled) instead of "yes" and
"no", respectively.
Update the documentation.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geert Uytterhoeven [Thu, 22 Sep 2011 19:47:38 +0000 (21:47 +0200)]
zorro: Defer device_register() until all devices have been identified
As the Amiga Zorro II address space is limited to 8.5 MiB and Zorro
devices can contain only one BAR, several Amiga Zorro II expansion
boards (mainly graphics cards) contain multiple Zorro devices: a small
one for the control registers and one (or more) for the graphics memory.
The conversion of cirrusfb to the new driver framework introduced a
regression: the driver contains a zorro_driver for the first Zorro
device, and uses the (old) zorro_find_device() call to find the second
Zorro device.
However, as the Zorro core calls device_register() as soon as a Zorro
device is identified, it may not have identified the second Zorro device
belonging to the same physical Zorro expansion card. Hence cirrusfb
could no longer find the second part of the Picasso II graphics card,
causing a NULL pointer dereference.
Defer the registration of Zorro devices with the driver framework until
all Zorro devices have been identified to fix this.
Note that the alternative solution (modifying cirrusfb to register a
zorro_driver for all Zorro devices belonging to a graphics card, instead
of only for the first one, and adding a synchronization mechanism to
defer initialization until all have been found), is not an option, as on
some cards one device may be optional (e.g. the second bank of 2 MiB of
graphics memory on the Picasso IV in Zorro II mode).
Reported-by: Ingo Jürgensmann <ij@2011.bluespice.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 22 Sep 2011 16:32:21 +0000 (09:32 -0700)]
Merge branch 'for-linus' of git://git390.marist.edu/linux-2.6
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] kvm: extension capability for new address space layout
[S390] kvm: fix address mode switching
Ben Hutchings [Thu, 22 Sep 2011 13:39:52 +0000 (14:39 +0100)]
ALSA: fm801: Gracefully handle failure of tuner auto-detect
Commit
9676001559fce06e37c7dc230ab275f605556176
("ALSA: fm801: add error handling if auto-detect fails") seems to
break systems that were previously working without a tuner.
As a bonus, this should fix init and cleanup for the case where the
tuner is explicitly disabled.
Reported-and-tested-by: Hor Jiun Shyong <jiunshyong@gmail.com>
References: http://bugs.debian.org/641946
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@kernel.org [v3.0+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ben Hutchings [Thu, 22 Sep 2011 13:38:58 +0000 (14:38 +0100)]
ALSA: fm801: Fix double free in case of error in tuner detection
Commit
9676001559fce06e37c7dc230ab275f605556176
("ALSA: fm801: add error handling if auto-detect fails") added
incorrect error handling.
Once we have successfully called snd_device_new(), the cleanup
function fm801_free() will automatically be called by snd_card_free()
and we must *not* also call fm801_free() directly.
Reported-by: Hor Jiun Shyong <jiunshyong@gmail.com>
References: http://bugs.debian.org/641946
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@kernel.org [v3.0+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Wed, 21 Sep 2011 23:58:15 +0000 (16:58 -0700)]
Linux 3.1-rc7
Lasse Collin [Wed, 21 Sep 2011 14:30:50 +0000 (17:30 +0300)]
XZ: Fix incorrect XZ_BUF_ERROR
xz_dec_run() could incorrectly return XZ_BUF_ERROR if all of the
following was true:
- The caller knows how many bytes of output to expect and only provides
that much output space.
- When the last output bytes are decoded, the caller-provided input
buffer ends right before the LZMA2 end of payload marker. So LZMA2
won't provide more output anymore, but it won't know it yet and thus
won't return XZ_STREAM_END yet.
- A BCJ filter is in use and it hasn't left any unfiltered bytes in the
temp buffer. This can happen with any BCJ filter, but in practice
it's more likely with filters other than the x86 BCJ.
This fixes <https://bugzilla.redhat.com/show_bug.cgi?id=735408> where
Squashfs thinks that a valid file system is corrupt.
This also fixes a similar bug in single-call mode where the uncompressed
size of a block using BCJ + LZMA2 was 0 bytes and caller provided no
output space. Many empty .xz files don't contain any blocks and thus
don't trigger this bug.
This also tweaks a closely related detail: xz_dec_bcj_run() could call
xz_dec_lzma2_run() to decode into temp buffer when it was known to be
useless. This was harmless although it wasted a minuscule number of CPU
cycles.
Signed-off-by: Lasse Collin <lasse.collin@tukaani.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 21 Sep 2011 20:35:00 +0000 (13:35 -0700)]
Merge git://github.com/davem330/net
* git://github.com/davem330/net: (27 commits)
xfrm: Perform a replay check after return from async codepaths
fib:fix BUG_ON in fib_nl_newrule when add new fib rule
ixgbe: fix possible null buffer error
tg3: fix VLAN tagging regression
net: pxa168: Fix build errors by including interrupt.h
netconsole: switch init_netconsole() to late_initcall
gianfar: Fix overflow check and return value for gfar_get_cls_all()
ppp_generic: fix multilink fragment MTU calculation (again)
GRETH: avoid overwrite IP-stack's IP-frags checksum
GRETH: RX/TX bytes were never increased
ipv6: fix a possible double free
b43: Fix beacon problem in ad-hoc mode
Bluetooth: add support for 2011 mac mini
Bluetooth: Add MacBookAir4,1 support
Bluetooth: Fixed BT ST Channel reg order
r8169: do not enable the TBI for anything but the original 8169.
r8169: remove erroneous processing of always set bit.
r8169: fix WOL setting for 8105 and 8111evl
r8169: add MODULE_FIRMWARE for the firmware of 8111evl
r8169: fix the reset setting for 8111evl
...
Linus Torvalds [Wed, 21 Sep 2011 20:20:21 +0000 (13:20 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
* 'for-linus' of git://git.kernel.dk/linux-block:
floppy: use del_timer_sync() in init cleanup
blk-cgroup: be able to remove the record of unplugged device
block: Don't check QUEUE_FLAG_SAME_COMP in __blk_complete_request
mm: Add comment explaining task state setting in bdi_forker_thread()
mm: Cleanup clearing of BDI_pending bit in bdi_forker_thread()
block: simplify force plug flush code a little bit
block: change force plug flush call order
block: Fix queue_flag update when rq_affinity goes from 2 to 1
block: separate priority boosting from REQ_META
block: remove READ_META and WRITE_META
xen-blkback: fixed indentation and comments
xen-blkback: Don't disconnect backend until state switched to XenbusStateClosed.
Alexander Sverdlin [Wed, 21 Sep 2011 07:51:40 +0000 (09:51 +0200)]
init: carefully handle loglevel option on kernel cmdline.
When a malformed loglevel value (for example "${abc}") is passed on the
kernel cmdline, the loglevel itself is being set to 0.
That then suppresses all following messages, including all the errors
and crashes caused by other malformed cmdline options. This could make
debugging process quite tricky.
This patch leaves the previous value of loglevel if the new value is
incorrect and reports an error code in this case.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@sysgo.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Hansen [Tue, 20 Sep 2011 22:19:41 +0000 (15:19 -0700)]
teach /proc/$pid/numa_maps about transparent hugepages
This is modeled after the smaps code.
It detects transparent hugepages and then does a single gather_stats()
for the page as a whole. This has two benifits:
1. It is more efficient since it does many pages in a single shot.
2. It does not have to break down the huge page.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Hansen [Tue, 20 Sep 2011 22:19:39 +0000 (15:19 -0700)]
break out numa_maps gather_pte_stats() checks
gather_pte_stats() does a number of checks on a target page
to see whether it should even be considered for statistics.
This breaks that code out in to a separate function so that
we can use it in the transparent hugepage case in the next
patch.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Acked-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Christoph Lameter <cl@gentwo.org>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Hansen [Tue, 20 Sep 2011 22:19:38 +0000 (15:19 -0700)]
make /proc/$pid/numa_maps gather_stats() take variable page size
We need to teach the numa_maps code about transparent huge pages. The
first step is to teach gather_stats() that the pte it is dealing with
might represent more than one page.
Note that will we use this in a moment for transparent huge pages since
they have use a single pmd_t which _acts_ as a "surrogate" for a bunch
of smaller pte_t's.
I'm a _bit_ unhappy that this interface counts in hugetlbfs page sizes
for hugetlbfs pages and PAGE_SIZE for normal pages. That means that to
figure out how many _bytes_ "dirty=1" means, you must first know the
hugetlbfs page size. That's easier said than done especially if you
don't have visibility in to the mount.
But, that's probably a discussion for another day especially since it
would change behavior to fix it. But, just in case anyone wonders why
this patch only passes a '1' in the hugetlb case...
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Steffen Klassert [Tue, 20 Sep 2011 23:38:58 +0000 (23:38 +0000)]
xfrm: Perform a replay check after return from async codepaths
When asyncronous crypto algorithms are used, there might be many
packets that passed the xfrm replay check, but the replay advance
function is not called yet for these packets. So the replay check
function would accept a replay of all of these packets. Also the
system might crash if there are more packets in async processing
than the size of the anti replay window, because the replay advance
function would try to update the replay window beyond the bounds.
This pach adds a second replay check after resuming from the async
processing to fix these issues.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gao feng [Sun, 11 Sep 2011 15:36:05 +0000 (15:36 +0000)]
fib:fix BUG_ON in fib_nl_newrule when add new fib rule
add new fib rule can cause BUG_ON happen
the reproduce shell is
ip rule add pref 38
ip rule add pref 38
ip rule add to 192.168.3.0/24 goto 38
ip rule del pref 38
ip rule add to 192.168.3.0/24 goto 38
ip rule add pref 38
then the BUG_ON will happen
del BUG_ON and use (ctarget == NULL) identify whether this rule is unresolved
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Brown [Tue, 20 Sep 2011 10:41:54 +0000 (11:41 +0100)]
ASoC: Ensure we generate a driver name
Commit
873bd4c (ASoC: Don't set invalid name string to snd_card->driver
field) broke generation of a driver name for all ASoC cards relying on the
automatic generation of one. Fix this by using the old default with spaces
replaced by underscores.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Carsten Emde [Wed, 21 Sep 2011 08:22:11 +0000 (10:22 +0200)]
floppy: use del_timer_sync() in init cleanup
When no floppy is found the module code can be released while a timer
function is pending or about to be executed.
CPU0 CPU1
floppy_init()
timer_softirq()
spin_lock_irq(&base->lock);
detach_timer();
spin_unlock_irq(&base->lock);
-> Interrupt
del_timer();
return -ENODEV;
module_cleanup();
<- EOI
call_timer_fn();
OOPS
Use del_timer_sync() to prevent this.
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Wanlong Gao [Wed, 21 Sep 2011 08:22:10 +0000 (10:22 +0200)]
blk-cgroup: be able to remove the record of unplugged device
The bug is we're not able to remove the device from blkio cgroup's
per-device control files if it gets unplugged.
To reproduce the bug:
# mount -t cgroup -o blkio xxx /cgroup
# cd /cgroup
# echo "8:0 1000" > blkio.throttle.read_bps_device
# unplug the device
# cat blkio.throttle.read_bps_device
8:0 1000
# echo "8:0 0" > blkio.throttle.read_bps_device
-bash: echo: write error: No such device
After patching, the device removal will succeed.
Thanks for the comments of Paul, Zefan, and Vivek.
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Paul Menage <paul@paulmenage.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jesse Brandeburg [Tue, 20 Sep 2011 15:13:03 +0000 (15:13 +0000)]
ixgbe: fix possible null buffer error
It seems that at least one PPC machine would occasionally give a (valid) 0 as
the return value from dma_map, this caused the ixgbe code to not work
correctly. A fix is pending in the PPC tree to not return 0 from dma map, but
we can also fix the driver to make sure we don't mess up in other arches as
well.
This patch is applicable to all current stable kernels.
Ref: https://bugzilla.redhat.com/show_bug.cgi?id=683611
Reported-by: Neil Horman <nhorman@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: stable@kernel.org
Tested-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kasper Pedersen [Tue, 20 Sep 2011 12:41:17 +0000 (12:41 +0000)]
tg3: fix VLAN tagging regression
commit
92cd3a17ce9c719abb4c28dee3438e0c641f8de4
tg3: Simplify tx bd assignments
broke VLAN tagging on outbound packets.
It ifdef'ed BCM_KERNEL_SUPPORTS_8021Q, but this
is not set anywhere. So vlan never gets set, and
all packets are sent with vlan=0.
v2: We can just remove the test. vlan_tx_tag_present
is valid regardless of whether the 802.1q module
is built.
Tested on BCM5721 rev 11.
Signed-off-by: Kasper Pedersen <kernel@kasperkp.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 20 Sep 2011 21:23:16 +0000 (14:23 -0700)]
Merge branch 'fixes' of git://git.linaro.org/people/arnd/arm-soc
* 'fixes' of git://git.linaro.org/people/arnd/arm-soc:
mach-integrator: fix VGA base regression
arm/dt: Tegra: Update SDHCI nodes to match bindings
ARM: EXYNOS4: fix incorrect pad configuration for keypad row lines
ARM: SAMSUNG: fix to prevent declaring duplicated
ARM: SAMSUNG: fix watchdog reset issue with clk_get()
ARM: S3C64XX: Remove un-used code backlight code on SMDK6410
ARM: EXYNOS4: restart clocksource while system resumes
ARM: EXYNOS4: Fix routing timer interrupt to offline CPU
ARM: EXYNOS4: Fix return type of local_timer_setup()
ARM: EXYNOS4: Fix wrong pll type for vpll
ARM: Dove: fix second SPI initialization call
Linus Torvalds [Tue, 20 Sep 2011 21:22:55 +0000 (14:22 -0700)]
Merge branch 'for-linus' of git://github.com/chrismason/linux
* 'for-linus' of git://github.com/chrismason/linux:
Btrfs: reserve sufficient space for ioctl clone
Seth Jennings [Tue, 20 Sep 2011 20:09:56 +0000 (13:09 -0700)]
staging: zcache: fix cleancache crash
After commit
c5f5c4db3938 ("staging: zcache: fix crash on high memory
swap") cleancache crashes on the first successful get. This was caused
by a remaining virt_to_page() call in zcache_pampd_get_data_and_free()
that only gets run in the cleancache path.
The patch converts the virt_to_page() to struct page casting like was
done for other instances in
c5f5c4db3938.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Tested-By: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Acked-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Walleij [Sun, 4 Sep 2011 21:40:08 +0000 (23:40 +0200)]
mach-integrator: fix VGA base regression
The changes introduced in commit
cc22b4c18540e5e8bf55c7d124044f9317527d3c
"ARM: set vga memory base at run-time"
Makes the Integrator/AP freeze completely. I appears that
this is due to the VGA base address being assigned at PCI
init time, while this base is needed earlier than that.
Moving the initialization of the base address to the
.map_io function solves this problem.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Stephen Warren [Tue, 20 Sep 2011 16:46:25 +0000 (10:46 -0600)]
arm/dt: Tegra: Update SDHCI nodes to match bindings
The bindings were recently updated to have separate properties for each
type of GPIO. Update the Device Tree source to match that.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tanmay Upadhyay [Mon, 5 Sep 2011 19:32:04 +0000 (19:32 +0000)]
net: pxa168: Fix build errors by including interrupt.h
Commit
a6b7a407865aab9f849dd99a71072b7cd1175116 removed
linux/interrupt.h from netdevice.h. This fixes below build failure
drivers/net/pxa168_eth.c: In function 'pxa168_eth_collect_events':
drivers/net/pxa168_eth.c:866: error: 'IRQ_NONE' undeclared (first use in this function)
drivers/net/pxa168_eth.c:866: error: (Each undeclared identifier is reported only once
drivers/net/pxa168_eth.c:866: error: for each function it appears in.)
drivers/net/pxa168_eth.c: At top level:
drivers/net/pxa168_eth.c:913: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'pxa168_eth_int_handler'
drivers/net/pxa168_eth.c: In function 'pxa168_eth_open':
drivers/net/pxa168_eth.c:1133: error: implicit declaration of function 'request_irq'
drivers/net/pxa168_eth.c:1133: error: 'pxa168_eth_int_handler' undeclared (first use in this function)
drivers/net/pxa168_eth.c:1134: error: 'IRQF_DISABLED' undeclared (first use in this function)
drivers/net/pxa168_eth.c:1160: error: implicit declaration of function 'free_irq'
Signed-off-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lin Ming [Tue, 20 Sep 2011 19:45:07 +0000 (15:45 -0400)]
netconsole: switch init_netconsole() to late_initcall
Commit
88491d8(drivers/net: Kconfig & Makefile cleanup) causes a
regression that netconsole does not work if netconsole and network
device driver are build into kernel, because netconsole is linked
before network device driver.
Andrew Morton suggested to fix this with initcall ordering.
Fixes it by switching init_netconsole() to late_initcall.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Tue, 6 Sep 2011 12:44:25 +0000 (12:44 +0000)]
gianfar: Fix overflow check and return value for gfar_get_cls_all()
This function may currently fill one entry beyond the end of the
array it is given. It also doesn't return an error code in case
it does detect overflow.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Henry Wong [Sun, 18 Sep 2011 13:41:49 +0000 (13:41 +0000)]
ppp_generic: fix multilink fragment MTU calculation (again)
When using MLPPP, the maximum size of a fragment is incorrectly
calculated with an offset of -2.
This patch reverses the changes in the patch found here:
http://marc.info/?l=linux-netdev&m=
123541324010539&w=2
The value of hdrlen includes the size of both the 2-byte PPP protocol
field and the 2- or 4-byte multilink header (2+4=6 for long sequence
numbers, 2+2=4 for short sequence numbers). Section 2 of RFC1661 says
that the MRU that is negotiated (i.e., the MTU of the sending system)
includes only the PPP payload but not the protocol field, thus the
correct MTU should be the link's MTU minus the multilink header (mtu -
(hdrlen-2)).
The incorrect calculation causes Linux to fragment packets to a size two
bytes smaller than the allowed MTU. While not technically illegal, this
behaviour confounds MRU-tuning to avoid PPP-layer fragmentation.
Signed-off-by: Henry Wong <henry@stuffedcow.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Hellstrom [Fri, 9 Sep 2011 05:17:54 +0000 (05:17 +0000)]
GRETH: avoid overwrite IP-stack's IP-frags checksum
The GRETH GBIT core does not do checksum offloading for IP
segmentation. This patch adds a check in the xmit function to
determine if the stack has calculated the checksum for us.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Hellstrom [Thu, 8 Sep 2011 03:14:35 +0000 (03:14 +0000)]
GRETH: RX/TX bytes were never increased
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roy Li [Tue, 20 Sep 2011 19:10:16 +0000 (15:10 -0400)]
ipv6: fix a possible double free
When calling snmp6_alloc_dev fails, the snmp6 relevant memory
are freed by snmp6_alloc_dev. Calling in6_dev_finish_destroy
will free these memory twice.
Double free will lead that undefined behavior occurs.
Signed-off-by: Roy Li <rongqing.li@windriver.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Mason [Tue, 20 Sep 2011 18:49:29 +0000 (14:49 -0400)]
Merge branch 'btrfs-3.0' into for-linus
Sage Weil [Tue, 20 Sep 2011 18:48:51 +0000 (14:48 -0400)]
Btrfs: reserve sufficient space for ioctl clone
Fix a crash/BUG_ON in the clone ioctl due to insufficient reservation. We
need to reserve space for:
- adjusting the old extent (possibly splitting it)
- adding the new extent
- updating the inode
Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
David S. Miller [Tue, 20 Sep 2011 18:42:45 +0000 (14:42 -0400)]
Merge branch 'davem.r8169.fixes' of git://violet.fr.zoreil.com/romieu/linux
Linus Torvalds [Tue, 20 Sep 2011 17:28:52 +0000 (10:28 -0700)]
Merge git://git.samba.org/sfrench/cifs-2.6
* git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix broken sec=ntlmv2/i sec option (try #2)
Fix the conflict between rwpidforward and rw mount options
CIFS: Fix ERR_PTR dereference in cifs_get_root
cifs: fix possible memory corruption in CIFSFindNext
Linus Torvalds [Tue, 20 Sep 2011 17:24:46 +0000 (10:24 -0700)]
Merge git://www.linux-watchdog.org/linux-watchdog
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: Initconst section fixes for watchdog
watchdog: lantiq: fix watchdogs timeout handling
watchdog: hpwdt: prevent multiple "NMI occurred" messages
watchdog: WatchDog Timer Driver Core - use passed watchdog_device
Linus Torvalds [Tue, 20 Sep 2011 17:21:52 +0000 (10:21 -0700)]
Merge branch 'for-linus' of git://github.com/tiwai/sound
* 'for-linus' of git://github.com/tiwai/sound:
ALSA: HDA: Add support for IDT 92HD93
ALSA: hda/realtek - Fix auto-mute with HP+LO configuration
Christian Borntraeger [Tue, 20 Sep 2011 15:07:29 +0000 (17:07 +0200)]
[S390] kvm: extension capability for new address space layout
598841ca9919d008b520114d8a4378c4ce4e40a1 ([S390] use gmap address
spaces for kvm guest images) changed kvm on s390 to use a separate
address space for kvm guests. We can now put KVM guests anywhere
in the user address mode with a size up to 8PB - as long as the
memory is 1MB-aligned. This change was done without KVM extension
capability bit.
The change was added after 3.0, but we still have a chance to add
a feature bit before 3.1 (keeping the releases in a sane state).
We use number 71 to avoid collisions with other pending kvm patches
as requested by Alexander Graf.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Avi Kivity <avi@redhat.com>
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Christian Borntraeger [Tue, 20 Sep 2011 15:07:28 +0000 (17:07 +0200)]
[S390] kvm: fix address mode switching
598841ca9919d008b520114d8a4378c4ce4e40a1 ([S390] use gmap address
spaces for kvm guest images) changed kvm to use a separate address
space for kvm guests. This address space was switched in __vcpu_run
In some cases (preemption, page fault) there is the possibility that
this address space switch is lost.
The typical symptom was a huge amount of validity intercepts or
random guest addressing exceptions.
Fix this by doing the switch in sie_loop and sie_exit and saving the
address space in the gmap structure itself. Also use the preempt
notifier.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
John W. Linville [Tue, 20 Sep 2011 13:19:14 +0000 (09:19 -0400)]
Merge branch 'master' of ssh://infradead/~/public_git/wireless into for-davem
Andi Kleen [Thu, 15 Sep 2011 20:09:51 +0000 (13:09 -0700)]
watchdog: Initconst section fixes for watchdog
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
John Crispin [Wed, 24 Aug 2011 08:31:39 +0000 (10:31 +0200)]
watchdog: lantiq: fix watchdogs timeout handling
The enable function was using the global timeout variable for local operations.
This resulted in the value of the global variable being corrupted, thus
breaking the code.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-mips@linux-mips.org
Naga Chumbalkar [Tue, 9 Aug 2011 22:27:26 +0000 (22:27 +0000)]
watchdog: hpwdt: prevent multiple "NMI occurred" messages
On platforms with no iCRU support don't print two, (possibly conflicting),
"NMI occurred" messages when the firmware is unable to source the NMI.
Please note that one of the enhancements to the v1.3.0 hpwdt driver is to panic and allow
KDUMP to succeed even on NMIs that are unknown to the platform firmware.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Reviewed-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>