Shaohua Li [Thu, 6 Feb 2014 20:04:21 +0000 (12:04 -0800)]
swap: add a simple detector for inappropriate swapin readahead
This is a patch to improve swap readahead algorithm. It's from Hugh and
I slightly changed it.
Hugh's original changelog:
swapin readahead does a blind readahead, whether or not the swapin is
sequential. This may be ok on harddisk, because large reads have
relatively small costs, and if the readahead pages are unneeded they can
be reclaimed easily - though, what if their allocation forced reclaim of
useful pages? But on SSD devices large reads are more expensive than
small ones: if the readahead pages are unneeded, reading them in caused
significant overhead.
This patch adds very simplistic random read detection. Stealing the
PageReadahead technique from Konstantin Khlebnikov's patch, avoiding the
vma/anon_vma sophistications of Shaohua Li's patch, swapin_nr_pages()
simply looks at readahead's current success rate, and narrows or widens
its readahead window accordingly. There is little science to its
heuristic: it's about as stupid as can be whilst remaining effective.
The table below shows elapsed times (in centiseconds) when running a
single repetitive swapping load across a 1000MB mapping in 900MB ram
with 1GB swap (the harddisk tests had taken painfully too long when I
used mem=500M, but SSD shows similar results for that).
Vanilla is the 3.6-rc7 kernel on which I started; Shaohua denotes his
Sep 3 patch in mmotm and linux-next; HughOld denotes my Oct 1 patch
which Shaohua showed to be defective; HughNew this Nov 14 patch, with
page_cluster as usual at default of 3 (8-page reads); HughPC4 this same
patch with page_cluster 4 (16-page reads); HughPC0 with page_cluster 0
(1-page reads: no readahead).
HDD for swapping to harddisk, SSD for swapping to VertexII SSD. Seq for
sequential access to the mapping, cycling five times around; Rand for
the same number of random touches. Anon for a MAP_PRIVATE anon mapping;
Shmem for a MAP_SHARED anon mapping, equivalent to tmpfs.
One weakness of Shaohua's vma/anon_vma approach was that it did not
optimize Shmem: seen below. Konstantin's approach was perhaps mistuned,
50% slower on Seq: did not compete and is not shown below.
HDD Vanilla Shaohua HughOld HughNew HughPC4 HughPC0
Seq Anon 73921 76210 75611 76904 78191 121542
Seq Shmem 73601 73176 73855 72947 74543 118322
Rand Anon 895392 831243 871569 845197 846496 841680
Rand Shmem
1058375 1053486 827935 764955 764376 756489
SSD Vanilla Shaohua HughOld HughNew HughPC4 HughPC0
Seq Anon 24634 24198 24673 25107 21614 70018
Seq Shmem 24959 24932 25052 25703 22030 69678
Rand Anon 43014 26146 28075 25989 26935 25901
Rand Shmem 45349 45215 28249 24268 24138 24332
These tests are, of course, two extremes of a very simple case: under
heavier mixed loads I've not yet observed any consistent improvement or
degradation, and wider testing would be welcome.
Shaohua Li:
Test shows Vanilla is slightly better in sequential workload than Hugh's
patch. I observed with Hugh's patch sometimes the readahead size is
shrinked too fast (from 8 to 1 immediately) in sequential workload if
there is no hit. And in such case, continuing doing readahead is good
actually.
I don't prepare a sophisticated algorithm for the sequential workload
because so far we can't guarantee sequential accessed pages are swap out
sequentially. So I slightly change Hugh's heuristic - don't shrink
readahead size too fast.
Here is my test result (unit second, 3 runs average):
Vanilla Hugh New
Seq 356 370 360
Random 4525 2447 2444
Attached graph is the swapin/swapout throughput I collected with 'vmstat
2'. The first part is running a random workload (till around 1200 of
the x-axis) and the second part is running a sequential workload.
swapin and swapout throughput are almost identical in steady state in
both workloads. These are expected behavior. while in Vanilla, swapin
is much bigger than swapout especially in random workload (because wrong
readahead).
Original patches by: Shaohua Li and Konstantin Khlebnikov.
[fengguang.wu@intel.com: swapin_nr_pages() can be static]
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zongxun Wang [Thu, 6 Feb 2014 20:04:20 +0000 (12:04 -0800)]
ocfs2: free allocated clusters if error occurs after ocfs2_claim_clusters
Even if using the same jbd2 handle, we cannot rollback a transaction.
So once some error occurs after successfully allocating clusters, the
allocated clusters will never be used and it means they are lost. For
example, call ocfs2_claim_clusters successfully when expanding a file,
but failed in ocfs2_insert_extent. So we need free the allocated
clusters if they are not used indeed.
Signed-off-by: Zongxun Wang <wangzongxun@huawei.com>
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Acked-by: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Li Zefan <lizefan@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Thu, 6 Feb 2014 20:04:19 +0000 (12:04 -0800)]
Documentation/kernel-parameters.txt: fix memmap= language
Clean up descriptions of memmap= boot options.
Add periods (full stops), drop commas, change "used" to "reserved" or
"marked".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Andiry Xu <andiry.xu@gmail.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 6 Feb 2014 00:02:53 +0000 (16:02 -0800)]
Merge branch 'irq-core-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"This lot provides:
* Bugfixes for armada irq controller
* Updates to renesas irq chip
* Support for the TI-NSPIRE irq controller
Not strictly a bug fix only pull request, but important updates for
some of the arm Socs which I completely forgot to send last week.
Seems like my obliviousness is getting worse, I just can't remember
when it started"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Add support for TI-NSPIRE irqchip
irqchip: renesas-irqc: Enable mask on suspend
irqchip: renesas-irqc: Use lazy disable
irqchip: armada-370-xp: fix MSI race condition
irqchip: armada-370-xp: fix IPI race condition
Linus Torvalds [Thu, 6 Feb 2014 00:01:11 +0000 (16:01 -0800)]
Merge tag 'stable/for-linus-3.14-rc1-tag' of git://git./linux/kernel/git/xen/tip
Pull Xen fixes from Konrad Rzeszutek Wilk:
"Bug-fixes:
- Revert "xen/grant-table: Avoid m2p_override during mapping" as it
broke Xen ARM build.
- Fix CR4 not being set on AP processors in Xen PVH mode"
* tag 'stable/for-linus-3.14-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pvh: set CR4 flags for APs
Revert "xen/grant-table: Avoid m2p_override during mapping"
Linus Torvalds [Thu, 6 Feb 2014 00:00:27 +0000 (16:00 -0800)]
Merge tag 'please-pull-ia64-syscalls' of git://git./linux/kernel/git/aegl/linux
Pull ia64 update from Tony Luck:
"Wire up new sched_setattr and sched_getattr syscalls"
* tag 'please-pull-ia64-syscalls' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
[IA64] Wire up new sched_setattr and sched_getattr syscalls
Linus Torvalds [Wed, 5 Feb 2014 23:53:26 +0000 (15:53 -0800)]
Merge git://git.infradead.org/users/willy/linux-nvme
Pull NVMe driver update from Matthew Wilcox:
"Looks like I missed the merge window ... but these are almost all
bugfixes anyway (the ones that aren't have been baking for months)"
* git://git.infradead.org/users/willy/linux-nvme:
NVMe: Namespace use after free on surprise removal
NVMe: Correct uses of INIT_WORK
NVMe: Include device and queue numbers in interrupt name
NVMe: Add a pci_driver shutdown method
NVMe: Disable admin queue on init failure
NVMe: Dynamically allocate partition numbers
NVMe: Async IO queue deletion
NVMe: Surprise removal handling
NVMe: Abort timed out commands
NVMe: Schedule reset for failed controllers
NVMe: Device resume error handling
NVMe: Cache dev->pci_dev in a local pointer
NVMe: Fix lockdep warnings
NVMe: compat SG_IO ioctl
NVMe: remove deprecated IRQF_DISABLED
NVMe: Avoid shift operation when writing cq head doorbell
Linus Torvalds [Wed, 5 Feb 2014 23:52:26 +0000 (15:52 -0800)]
Merge tag 'regulator-v3.14-rc1' of git://git./linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of driver fixes here but the main thing is a fix to the
checks for deferred probe non-DT systems with fully specified
regulators which had been broken by a device tree fix which meant that
we wouldn't insert optional regulators.
This had slipped through the cracks since very few systems do that in
the first place and those that do it in mainline don't need optional
regulators anyway"
* tag 'regulator-v3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: s2mps11: Fix NULL pointer of_node value when using platform data
regulator: core: Correct default return value for full constraints
regulator: ab3100: cast fix
Linus Torvalds [Wed, 5 Feb 2014 23:51:42 +0000 (15:51 -0800)]
Merge git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes a number of concurrency issues on s390 where multiple users
of the same crypto transform may clobber each other's results"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: s390 - fix des and des3_ede ctr concurrency issue
crypto: s390 - fix des and des3_ede cbc concurrency issue
crypto: s390 - fix concurrency issue in aes-ctr mode
Ingo Molnar [Wed, 5 Feb 2014 05:51:37 +0000 (06:51 +0100)]
x86: Disable CONFIG_X86_DECODER_SELFTEST in allmod/allyesconfigs
It can take some time to validate the image, make sure
{allyes|allmod}config doesn't enable it.
I'd say randconfig will cover it often enough, and the failure is also
borderline build coverage related: you cannot really make the decoder
test fail via source level changes, only with changes in the build
environment, so I agree with Andi that we can disable this one too.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Paul Gortmaker paul.gortmaker@windriver.com>
Suggested-and-acked-by: Andi Kleen andi@firstfloor.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 5 Feb 2014 20:54:53 +0000 (12:54 -0800)]
execve: use 'struct filename *' for executable name passing
This changes 'do_execve()' to get the executable name as a 'struct
filename', and to free it when it is done. This is what the normal
users want, and it simplifies and streamlines their error handling.
The controlled lifetime of the executable name also fixes a
use-after-free problem with the trace_sched_process_exec tracepoint: the
lifetime of the passed-in string for kernel users was not at all
obvious, and the user-mode helper code used UMH_WAIT_EXEC to serialize
the pathname allocation lifetime with the execve() having finished,
which in turn meant that the trace point that happened after
mm_release() of the old process VM ended up using already free'd memory.
To solve the kernel string lifetime issue, this simply introduces
"getname_kernel()" that works like the normal user-space getname()
function, except with the source coming from kernel memory.
As Oleg points out, this also means that we could drop the tcomm[] array
from 'struct linux_binprm', since the pathname lifetime now covers
setup_new_exec(). That would be a separate cleanup.
Reported-by: Igor Zhbanov <i.zhbanov@samsung.com>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 4 Feb 2014 20:26:56 +0000 (12:26 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"Filipe is fixing compile and boot problems with our crc32c rework, and
Josef has disabled snapshot aware defrag for now.
As the number of snapshots increases, we're hitting OOM. For the
short term we're disabling things until a bigger fix is ready"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: use late_initcall instead of module_init
Btrfs: use btrfs_crc32c everywhere instead of libcrc32c
Btrfs: disable snapshot aware defrag for now
Linus Torvalds [Tue, 4 Feb 2014 20:26:16 +0000 (12:26 -0800)]
Merge tag 'nfs-for-3.14-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights:
- Fix NFSv3 acl regressions
- Fix NFSv4 memory corruption due to slot table abuse in
nfs4_proc_open_confirm
- nfs4_destroy_session must call rpc_destroy_waitqueue"
* tag 'nfs-for-3.14-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
fs: get_acl() must be allowed to return EOPNOTSUPP
NFSv3: Fix return value of nfs3_proc_setacls
NFSv3: Remove unused function nfs3_proc_set_default_acl
NFSv4.1: nfs4_destroy_session must call rpc_destroy_waitqueue
NFSv4: Fix memory corruption in nfs4_proc_open_confirm
nfs: fix setting of ACLs on file creation.
Linus Torvalds [Tue, 4 Feb 2014 20:20:01 +0000 (12:20 -0800)]
kbuild: don't enable DEBUG_INFO when building for COMPILE_TEST
It really isn't very interesting to have DEBUG_INFO when doing compile
coverage stuff (you wouldn't want to run the result anyway, that's kind
of the whole point of COMPILE_TEST), and it currently makes the build
take longer and use much more disk space for "all{yes,mod}config".
There's somewhat active discussion about this still, and we might end up
with some new config option for things like this (Andi points out that
the silly X86_DECODER_SELFTEST option also slows down the normal
coverage tests hugely), but I'm starting the ball rolling with this
simple one-liner.
DEBUG_INFO isn't that noticeable if you have tons of memory and a good
IO subsystem, but it hurts you a lot if you don't - for very little
upside for the common use.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Brown [Tue, 4 Feb 2014 12:58:19 +0000 (12:58 +0000)]
Merge remote-tracking branches 'regulator/fix/ab3100' and 'regulator/fix/s2mps11' into regulator-linus
Mark Brown [Tue, 4 Feb 2014 12:58:17 +0000 (12:58 +0000)]
Merge remote-tracking branch 'regulator/fix/core' into regulator-linus
Trond Myklebust [Mon, 3 Feb 2014 22:13:45 +0000 (17:13 -0500)]
Merge branch 'acl_fixes' into linux-next
Trond Myklebust [Fri, 31 Jan 2014 19:25:19 +0000 (14:25 -0500)]
fs: get_acl() must be allowed to return EOPNOTSUPP
posix_acl_xattr_get requires get_acl() to return EOPNOTSUPP if the
filesystem cannot support acls. This is needed for NFS, which can't
know whether or not the server supports acls until it tries to get/set
one.
This patch converts posix_acl_chmod and posix_acl_create to deal with
EOPNOTSUPP return values from get_acl().
Reported-by: Russell King <linux@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/20140130140834.GW15937@n2100.arm.linux.org.uk
Cc: Al Viro viro@zeniv.linux.org.uk>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Mukesh Rathor [Thu, 30 Jan 2014 00:15:18 +0000 (16:15 -0800)]
xen/pvh: set CR4 flags for APs
During bootup in the 'probe_page_size_mask' these CR4 flags are
set in there. But for AP processors they are not set as we do not
use 'secondary_startup_64' which the baremetal kernels uses.
Instead do it in this function which we use in Xen PVH during our
startup for AP processors.
As such fix it up to make sure we have that flag set.
Signed-off-by: Mukesh Rathor <mukesh.rathor@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Trond Myklebust [Sun, 2 Feb 2014 19:36:42 +0000 (14:36 -0500)]
NFSv3: Fix return value of nfs3_proc_setacls
nfs3_proc_setacls is used internally by the NFSv3 create operations
to set the acl after the file has been created. If the operation
fails because the server doesn't support acls, then it must return '0',
not -EOPNOTSUPP.
Reported-by: Russell King <linux@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/20140201010328.GI15937@n2100.arm.linux.org.uk
Cc: Christoph Hellwig <hch@lst.de>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Trond Myklebust [Sun, 2 Feb 2014 19:41:42 +0000 (14:41 -0500)]
NFSv3: Remove unused function nfs3_proc_set_default_acl
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Filipe David Borba Manana [Sat, 1 Feb 2014 21:27:56 +0000 (21:27 +0000)]
Btrfs: use late_initcall instead of module_init
It seems that when init_btrfs_fs() is called, crc32c/crc32c-intel might
not always be already initialized, which results in the call to crypto_alloc_shash()
returning -ENOENT, as experienced by Ahmet who reported this.
Therefore make sure init_btrfs_fs() is called after crc32c is initialized (which
is at initialization level 6, module_init), by using late_initcall (which is at
initialization level 7) instead of module_init for btrfs.
Reported-and-Tested-by: Ahmet Inan <ainan@mathematik.uni-freiburg.de>
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com>
Signed-off-by: Chris Mason <clm@fb.com>
Filipe David Borba Manana [Wed, 29 Jan 2014 21:06:04 +0000 (21:06 +0000)]
Btrfs: use btrfs_crc32c everywhere instead of libcrc32c
After the commit titled "Btrfs: fix btrfs boot when compiled as built-in",
LIBCRC32C requirement was removed from btrfs' Kconfig. This made it not
possible to build a kernel with btrfs enabled (either as module or built-in)
if libcrc32c is not enabled as well. So just replace all uses of libcrc32c
with the equivalent function in btrfs hash.h - btrfs_crc32c.
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com>
Signed-off-by: Chris Mason <clm@fb.com>
Josef Bacik [Wed, 29 Jan 2014 21:05:30 +0000 (16:05 -0500)]
Btrfs: disable snapshot aware defrag for now
It's just broken and it's taking a lot of effort to fix it, so for now just
disable it so people can defrag in peace. Thanks,
Cc: stable@vger.kernel.org
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Konrad Rzeszutek Wilk [Mon, 3 Feb 2014 11:43:59 +0000 (06:43 -0500)]
Revert "xen/grant-table: Avoid m2p_override during mapping"
This reverts commit
08ece5bb2312b4510b161a6ef6682f37f4eac8a1.
As it breaks ARM builds and needs more attention
on the ARM side.
Acked-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Linus Torvalds [Mon, 3 Feb 2014 00:42:13 +0000 (16:42 -0800)]
Linus 3.14-rc1
Linus Torvalds [Mon, 3 Feb 2014 00:32:53 +0000 (16:32 -0800)]
Merge branch 'parisc-3.14' of git://git./linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
"The three major changes in this patchset is a implementation for
flexible userspace memory maps, cache-flushing fixes (again), and a
long-discussed ABI change to make EWOULDBLOCK the same value as
EAGAIN.
parisc has been the only platform where we had EWOULDBLOCK != EAGAIN
to keep HP-UX compatibility. Since we will probably never implement
full HP-UX support, we prefer to drop this compatibility to make it
easier for us with Linux userspace programs which mostly never checked
for both values. We don't expect major fall-outs because of this
change, and if we face some, we will simply rebuild the necessary
applications in the debian archives"
* 'parisc-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: add flexible mmap memory layout support
parisc: Make EWOULDBLOCK be equal to EAGAIN on parisc
parisc: convert uapi/asm/stat.h to use native types only
parisc: wire up sched_setattr and sched_getattr
parisc: fix cache-flushing
parisc/sti_console: prefer Linux fonts over built-in ROM fonts
Mikulas Patocka [Tue, 28 Jan 2014 23:11:33 +0000 (00:11 +0100)]
hpfs: optimize quad buffer loading
HPFS needs to load 4 consecutive 512-byte sectors when accessing the
directory nodes or bitmaps. We can't switch to 2048-byte block size
because files are allocated in the units of 512-byte sectors.
Previously, the driver would allocate a 2048-byte area using kmalloc,
copy the data from four buffers to this area and eventually copy them
back if they were modified.
In the current implementation of the buffer cache, buffers are allocated
in the pagecache. That means that 4 consecutive 512-byte buffers are
stored in consecutive areas in the kernel address space. So, we don't
need to allocate extra memory and copy the content of the buffers there.
This patch optimizes the code to avoid copying the buffers. It checks
if the four buffers are stored in contiguous memory - if they are not,
it falls back to allocating a 2048-byte area and copying data there.
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mikulas Patocka [Tue, 28 Jan 2014 23:10:44 +0000 (00:10 +0100)]
hpfs: remember free space
Previously, hpfs scanned all bitmaps each time the user asked for free
space using statfs. This patch changes it so that hpfs scans the
bitmaps only once, remembes the free space and on next invocation of
statfs it returns the value instantly.
New versions of wine are hammering on the statfs syscall very heavily,
making some games unplayable when they're stored on hpfs, with load
times in minutes.
This should be backported to the stable kernels because it fixes
user-visible problem (excessive level load times in wine).
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Helge Deller [Fri, 31 Jan 2014 21:19:52 +0000 (22:19 +0100)]
parisc: add flexible mmap memory layout support
Add support for the flexible mmap memory layout (as described in
http://lwn.net/Articles/91829). This is especially very interesting on
parisc since we currently only support 32bit userspace (even with a
64bit Linux kernel).
Signed-off-by: Helge Deller <deller@gmx.de>
Guy Martin [Thu, 16 Jan 2014 16:17:53 +0000 (17:17 +0100)]
parisc: Make EWOULDBLOCK be equal to EAGAIN on parisc
On Linux, only parisc uses a different value for EWOULDBLOCK which
causes a lot of troubles for applications not checking for both values.
Since the hpux compat is long dead, make EWOULDBLOCK behave the same as
all other architectures.
Signed-off-by: Guy Martin <gmsoft@tuxicoman.be>
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Fri, 31 Jan 2014 22:00:38 +0000 (23:00 +0100)]
parisc: convert uapi/asm/stat.h to use native types only
The stat.h header file is exported to userspace. Some userspace
applications failed to compile due to missing/unknown types, so we
better convert it to use native types only (like it's done on other
architectures too).
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Fri, 31 Jan 2014 21:29:17 +0000 (22:29 +0100)]
parisc: wire up sched_setattr and sched_getattr
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Fri, 31 Jan 2014 20:33:17 +0000 (21:33 +0100)]
parisc: fix cache-flushing
This commit:
f8dae00684d678afa13041ef170cecfd1297ed40: parisc: Ensure full cache coherency for kmap/kunmap
caused negative caching side-effects, e.g. hanging processes with expect and
too many inequivalent alias messages from flush_dcache_page() on Debian 5 systems.
This patch now partly reverts it and has been in production use on our debian buildd
makeservers since a week without any major problems.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Fri, 31 Jan 2014 14:39:40 +0000 (15:39 +0100)]
parisc/sti_console: prefer Linux fonts over built-in ROM fonts
The built-in ROM fonts lack many necessary ASCII characters, which is
why it makes sens to prefer the Linux fonts instead if they are
available. This makes consoles on STI graphics cards which are not
supported by the stifb driver (e.g. Visualize FXe) looks much nicer.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v3.13
Linus Torvalds [Sun, 2 Feb 2014 19:30:57 +0000 (11:30 -0800)]
Merge branch 'hwmon-for-linus' of git://git./linux/kernel/git/jdelvare/staging
Pull hwmon kconfig fixes from Jean Delvare.
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: Fix SENSORS_TMP102 dependencies to eliminate build errors
hwmon: Fix SENSORS_LM75 dependencies to eliminate build errors
Linus Torvalds [Sun, 2 Feb 2014 19:30:08 +0000 (11:30 -0800)]
Merge branch 'slab/next' of git://git./linux/kernel/git/penberg/linux
Pull SLAB changes from Pekka Enberg:
"Random bug fixes that have accumulated in my inbox over the past few
months"
* 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
mm: Fix warning on make htmldocs caused by slab.c
mm: slub: work around unneeded lockdep warning
mm: sl[uo]b: fix misleading comments
slub: Fix possible format string bug.
slub: use lockdep_assert_held
slub: Fix calculation of cpu slabs
slab.h: remove duplicate kmalloc declaration and fix kernel-doc warnings
Linus Torvalds [Sun, 2 Feb 2014 19:28:48 +0000 (11:28 -0800)]
Merge branch 'release' of git://git./linux/kernel/git/lenb/linux
Pull turbostat updates from Len Brown.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: introduce -s to dump counters
tools/power turbostat: remove unused command line option
turbostat: Add option to report joules consumed per sample
turbostat: run on HSX
turbostat: Add a .gitignore to ignore the compiled turbostat binary
turbostat: Clean up error handling; disambiguate error messages; use err and errx
turbostat: Factor out common function to open file and exit on failure
turbostat: Add a helper to parse a single int out of a file
turbostat: Check return value of fscanf
turbostat: Use GCC's CPUID functions to support PIC
turbostat: Don't attempt to printf an off_t with %zx
turbostat: Don't put unprocessed uapi headers in the include path
Linus Torvalds [Sun, 2 Feb 2014 19:11:06 +0000 (11:11 -0800)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's a set of patches for (hopefully) -rc1. Some of them are fixes,
but a good number of them also do things such as enable new drivers in
the defconfigs for platforms that have such devices, increases
coverage of the multiplatform defconfig and some DTS changes that
plumbs up some of the devices that now have bindings and driver
support.
The commit dates are recent; we've mostly collected these fixes in the
last few days but I also had to rebuild the branch yesterday to sort
out some internal conflicts which reset the timestamps. The changes
should have been tested by each platform maintainer already (and few
of them have cross-platform impact) so I'm personally not too
concerned by it at this time"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
ARM: multi_v7_defconfig: remove redundant entries and re-enable TI_EDMA
ARM: multi_v7_defconfig: add mvebu drivers
clocksource: kona: Add basic use of external clock
drivers: bus: fix CCI driver kcalloc call parameters swap
ARM: dts: bcm28155-ap: Fix Card Detection GPIO
ARM: multi_v7_defconfig: Select CONFIG_AT803X_PHY
ARM: keystone: config: fix build warning when CONFIG_DMADEVICES is not set
MAINTAINERS: ARM: SiRF: use regex patterns to involve all SiRF drivers
ARM: dts: zynq: Add SDHCI nodes
ARM: hisi: don't select SMP
ARM: tegra: rebuild tegra_defconfig to add DEBUG_FS
ARM: multi_v7: copy most options from tegra_defconfig
ARM: iop32x: fix power off handling for the EM7210 board
ARM: integrator: restore static map on the CP
ARM: msm_defconfig: Enable MSM clock drivers
ARM: dts: msm: Add clock controller nodes and hook into uart
ARM: OMAP4+: move errata initialization to omap4_pm_init_early
ARM: OMAP4460: cpuidle: Extend PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD on cpuidle
ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP)
ARM: shmobile: r8a7790.dtsi: ficx i2c[0-3] clock reference
...
Keith Busch [Fri, 31 Jan 2014 23:53:39 +0000 (16:53 -0700)]
NVMe: Namespace use after free on surprise removal
An nvme block device may have open references when the device is
removed. New commands may still be sent on the removed device, so we
need to ref count the opens, return errors for new commands, and not
free the namespace and nvme_dev until all references are closed.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Jean Delvare [Sun, 2 Feb 2014 16:59:07 +0000 (17:59 +0100)]
hwmon: Fix SENSORS_TMP102 dependencies to eliminate build errors
Similar to what was done for the lm75 driver.
Add depends on THERMAL since that is what provides the
register/unregister functions above, but only if THERMAL_OF was
selected as this is an optional feature of the driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Jean Delvare [Sun, 2 Feb 2014 16:59:07 +0000 (17:59 +0100)]
hwmon: Fix SENSORS_LM75 dependencies to eliminate build errors
Based on an earlier attempt by Randy Dunlap.
Fix SENSORS_LM75 dependencies to eliminate build errors:
drivers/built-in.o: In function `lm75_remove':
lm75.c:(.text+0x12bd8c): undefined reference to `thermal_zone_of_sensor_unregister'
drivers/built-in.o: In function `lm75_probe':
lm75.c:(.text+0x12c123): undefined reference to `thermal_zone_of_sensor_register'
Add depends on THERMAL since that is what provides the
register/unregister functions above, but only if THERMAL_OF was
selected as this is an optional feature of the driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Andy Shevchenko [Thu, 23 Jan 2014 15:13:15 +0000 (17:13 +0200)]
tools/power turbostat: introduce -s to dump counters
The new option allows just run turbostat and get dump of counter values. It's
useful when we have something more than one program to test.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Andy Shevchenko [Thu, 23 Jan 2014 15:13:14 +0000 (17:13 +0200)]
tools/power turbostat: remove unused command line option
The -s is not used, let's remove it, and update quick help accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Trond Myklebust [Sat, 1 Feb 2014 18:47:06 +0000 (13:47 -0500)]
NFSv4.1: nfs4_destroy_session must call rpc_destroy_waitqueue
There may still be timers active on the session waitqueues. Make sure
that we kill them before freeing the memory.
Cc: stable@vger.kernel.org # 3.12+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Trond Myklebust [Sat, 1 Feb 2014 19:53:23 +0000 (14:53 -0500)]
NFSv4: Fix memory corruption in nfs4_proc_open_confirm
nfs41_wake_and_assign_slot() relies on the task->tk_msg.rpc_argp and
task->tk_msg.rpc_resp always pointing to the session sequence arguments.
nfs4_proc_open_confirm tries to pull a fast one by reusing the open
sequence structure, thus causing corruption of the NFSv4 slot table.
Cc: stable@vger.kernel.org # 3.12+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Linus Torvalds [Sat, 1 Feb 2014 19:03:16 +0000 (11:03 -0800)]
Merge branch 'misc' of git://git./linux/kernel/git/mmarek/kbuild
Pull misc kbuild changes from Michal Marek:
"The non-critical part of kbuild is small this time:
- Three fixes for make deb-pkg
- A new coccinelle check
One of the deb-pkg fixes is a leftover from the last merge window,
hence the merge commit"
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
deb-pkg: Fix building for MIPS big-endian or ARM OABI
deb-pkg: Fix cross-building linux-headers package
scripts: Coccinelle script for pm_runtime_* return checks with IS_ERR_VALUE
deb-pkg: Inhibit initramfs builders if CONFIG_BLK_DEV_INITRD is not set
Pali Rohár [Tue, 28 Jan 2014 20:26:44 +0000 (20:26 +0000)]
afs: proc cells and rootcell are writeable
Both proc files are writeable and used for configuring cells. But
there is missing correct mode flag for writeable files. Without
this patch both proc files are read only.
[ It turns out they aren't really read-only, since root can write to
them even if the write bit isn't set due to CAP_DAC_OVERRIDE ]
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Heiko Carstens [Fri, 31 Jan 2014 06:50:36 +0000 (07:50 +0100)]
tile: remove compat_sys_lookup_dcookie declaration to fix compile error
With commit
d8d14bd09cdd ("fs/compat: fix lookup_dcookie() parameter
handling") I changed the type of the len parameter of the
lookup_dcookie() syscall.
However I missed that there was still a stale declaration in
arch/tile/.. which now causes a compile error on tile:
In file included from fs/dcookies.c:28:0:
include/linux/compat.h:425:17: error: conflicting types for 'compat_sys_lookup_dcookie'
fs/dcookies.c:207:1: error: conflicting types for 'compat_sys_lookup_dcookie'
Simply remove the declaration in the tile architecture, which is only a
leftover from before the different compat lookup_dcookie() versions have
been merged. The correct declaration is now in include/linux/compat.h
The build error was reported by Fenguang's build bot.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 1 Feb 2014 18:52:45 +0000 (10:52 -0800)]
Merge branch 'for-linus' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"A set of cifs fixes (mostly for symlinks, and SMB2 xattrs) and
cleanups"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix check for regular file in couldbe_mf_symlink()
[CIFS] Fix SMB2 mounts so they don't try to set or get xattrs via cifs
CIFS: Cleanup cifs open codepath
CIFS: Remove extra indentation in cifs_sfu_type
CIFS: Cleanup cifs_mknod
CIFS: Cleanup CIFSSMBOpen
cifs: Add support for follow_link on dfs shares under posix extensions
cifs: move unix extension call to cifs_query_symlink()
cifs: Re-order M-F Symlink code
cifs: Add create MFSymlinks to protocol ops struct
cifs: use protocol specific call for query_mf_symlink()
cifs: Rename MF symlink function names
cifs: Rename and cleanup open_query_close_cifs_symlink()
cifs: Fix memory leak in cifs_hardlink()
Linus Torvalds [Sat, 1 Feb 2014 18:43:45 +0000 (10:43 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"Several obvious fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Fix mountpoint reference leakage in linkat
hfsplus: use xattr handlers for removexattr
Typo in compat_sys_lseek() declaration
fs/super.c: sync ro remount after blocking writers
vfs: unexport the getname() symbol
Linus Torvalds [Sat, 1 Feb 2014 18:29:59 +0000 (10:29 -0800)]
Merge tag 'staging-3.14-rc1' of git://git./linux/kernel/git/gregkh/staging
Pull rtl8812ae staging wireless driver from Greg KH:
"Here's a single staging driver for a wireless chipset that has shown
up in the SteamBox hardware. It is merged separately from the "main"
staging pull request to sync up with the wireless api changes that
came in from the networking tree.
It's self-contained and works for me and others. Larry will be
replacing it with a "real" driver for 3.15, but for now this one is
needed"
* tag 'staging-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8821ae: Enable build by reverting BROKEN marking
staging: r8821ae: Fix build problems
Staging: rtl8812ae: disable due to build errors
Staging: rtl8821ae: add TODO file
Staging: rtl8821ae: removed unused functions and variables
Staging: rtl8821ae: rc.c: fix up function prototypes
Staging: rtl8812ae: Add Realtek 8821 PCI WIFI driver
Rafael J. Wysocki [Sat, 1 Feb 2014 14:38:29 +0000 (15:38 +0100)]
Revert "PCI: Remove from bus_list and release resources in pci_release_dev()"
Revert commit
ef83b0781a73 "PCI: Remove from bus_list and release
resources in pci_release_dev()" that made some nasty race conditions
become possible. For example, if a Thunderbolt link is unplugged
and then replugged immediately, the pci_release_dev() resulting from
the hot-remove code path may be racing with the hot-add code path
which after that commit causes various kinds of breakage to happen
(up to and including a hard crash of the whole system).
Moreover, the problem that commit
ef83b0781a73 attempted to address
cannot happen any more after commit
8a4c5c329de7 "PCI: Check parent
kobject in pci_destroy_dev()", because pci_destroy_dev() will now
return immediately if it has already been executed for the given
device.
Note, however, that the invocation of msi_remove_pci_irq_vectors()
removed by commit
ef83b0781a73 from pci_free_resources() along with
the other changes made by it is not added back because of subsequent
code changes depending on that modification.
Fixes:
ef83b0781a73 (PCI: Remove from bus_list and release resources in pci_release_dev())
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Olof Johansson [Fri, 31 Jan 2014 23:21:08 +0000 (15:21 -0800)]
ARM: multi_v7_defconfig: remove redundant entries and re-enable TI_EDMA
TI_EDMA fell out of automatically selected options in the multi_v7
defconfig due to a select being removed from the davinci Kconfig entry. So
we need to re-enable explicitly to not regress some platforms.
The rest is just the result of running 'make multi_v7_defconfig + make
savedefconfig' to remove entries that are no longer needed due to changed
dependencies/selects or defaults.
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 31 Jan 2014 23:20:07 +0000 (15:20 -0800)]
ARM: multi_v7_defconfig: add mvebu drivers
Recent boot farm testing has highlighted some issues with mvebu and
multiplatform kernels. Increase the test coverage so we can discover
these issues earlier.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
Tim Kryger [Thu, 5 Dec 2013 19:20:43 +0000 (11:20 -0800)]
clocksource: kona: Add basic use of external clock
When an clock is specified in the device tree, enable it and use it to
determine the external clock frequency.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Christian Daudt <bcm@fixthebug.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Noah Massey [Fri, 31 Jan 2014 02:31:12 +0000 (21:31 -0500)]
nfs: fix setting of ACLs on file creation.
nfs3_get_acl() tries to skip posix equivalent ACLs, but misinterprets
the return value of posix_acl_equiv_mode(). Fix it.
This is a regression introduced by
"nfs: use generic posix ACL infrastructure for v3 Posix ACLs"
CC: Christoph Hellwig <hch@infradead.org>
CC: linux-nfs@vger.kernel.org
CC: linux-fsdevel@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Linus Torvalds [Fri, 31 Jan 2014 23:39:07 +0000 (15:39 -0800)]
Merge tag 'nfs-for-3.14-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights:
- Fix several races in nfs_revalidate_mapping
- NFSv4.1 slot leakage in the pNFS files driver
- Stable fix for a slot leak in nfs40_sequence_done
- Don't reject NFSv4 servers that support ACLs with only ALLOW aces"
* tag 'nfs-for-3.14-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
nfs: initialize the ACL support bits to zero.
NFSv4.1: Cleanup
NFSv4.1: Clean up nfs41_sequence_done
NFSv4: Fix a slot leak in nfs40_sequence_done
NFSv4.1 free slot before resending I/O to MDS
nfs: add memory barriers around NFS_INO_INVALID_DATA and NFS_INO_INVALIDATING
NFS: Fix races in nfs_revalidate_mapping
sunrpc: turn warn_gssd() log message into a dprintk()
NFS: fix the handling of NFS_INO_INVALID_DATA flag in nfs_revalidate_mapping
nfs: handle servers that support only ALLOW ACE type.
Linus Torvalds [Fri, 31 Jan 2014 23:38:09 +0000 (15:38 -0800)]
Merge tag 'sound-fix-3.14-rc1' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The big chunks here are the updates for oxygen driver for Xonar DG
devices, which were slipped from the previous pull request. They are
device-specific and thus not too dangerous.
Other than that, all patches are small bug fixes, mainly for Samsung
build fixes, a few HD-audio enhancements, and other misc ASoC fixes.
(And this time ASoC merge is less than Octopus, lucky seven :)"
* tag 'sound-fix-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (42 commits)
ALSA: hda/hdmi - allow PIN_OUT to be dynamically enabled
ALSA: hda - add headset mic detect quirks for another Dell laptop
ALSA: oxygen: Xonar DG(X): cleanup and minor changes
ALSA: oxygen: Xonar DG(X): modify high-pass filter control
ALSA: oxygen: Xonar DG(X): modify input select functions
ALSA: oxygen: Xonar DG(X): modify capture volume functions
ALSA: oxygen: Xonar DG(X): use headphone volume control
ALSA: oxygen: Xonar DG(X): modify playback output select
ALSA: oxygen: Xonar DG(X): capture from I2S channel 1, not 2
ALSA: oxygen: Xonar DG(X): move the mixer code into another file
ALSA: oxygen: modify CS4245 register dumping function
ALSA: oxygen: modify adjust_dg_dac_routing function
ALSA: oxygen: Xonar DG(X): modify DAC/ADC parameters function
ALSA: oxygen: Xonar DG(X): modify initialization functions
ALSA: oxygen: Xonar DG(X): add new CS4245 SPI functions
ALSA: oxygen: additional definitions for the Xonar DG/DGX card
ALSA: oxygen: change description of the xonar_dg.c file
ALSA: oxygen: export oxygen_update_dac_routing symbol
ALSA: oxygen: add mute mask for the OXYGEN_PLAY_ROUTING register
ALSA: oxygen: modify the SPI writing function
...
Linus Torvalds [Fri, 31 Jan 2014 23:31:23 +0000 (15:31 -0800)]
Merge branch 'for-next' of git://git./linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- add support for SCSI Referrals (Hannes)
- add support for T10 DIF into target core (nab + mkp)
- add support for T10 DIF emulation in FILEIO + RAMDISK backends (Sagi + nab)
- add support for T10 DIF -> bio_integrity passthrough in IBLOCK backend (nab)
- prep changes to iser-target for >= v3.15 T10 DIF support (Sagi)
- add support for qla2xxx N_Port ID Virtualization - NPIV (Saurav + Quinn)
- allow percpu_ida_alloc() to receive task state bitmask (Kent)
- fix >= v3.12 iscsi-target session reset hung task regression (nab)
- fix >= v3.13 percpu_ref se_lun->lun_ref_active race (nab)
- fix a long-standing network portal creation race (Andy)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (51 commits)
target: Fix percpu_ref_put race in transport_lun_remove_cmd
target/iscsi: Fix network portal creation race
target: Report bad sector in sense data for DIF errors
iscsi-target: Convert gfp_t parameter to task state bitmask
iscsi-target: Fix connection reset hang with percpu_ida_alloc
percpu_ida: Make percpu_ida_alloc + callers accept task state bitmask
iscsi-target: Pre-allocate more tags to avoid ack starvation
qla2xxx: Configure NPIV fc_vport via tcm_qla2xxx_npiv_make_lport
qla2xxx: Enhancements to enable NPIV support for QLOGIC ISPs with TCM/LIO.
qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
IB/isert: pass scatterlist instead of cmd to fast_reg_mr routine
IB/isert: Move fastreg descriptor creation to a function
IB/isert: Avoid frwr notation, user fastreg
IB/isert: seperate connection protection domains and dma MRs
tcm_loop: Enable DIF/DIX modes in SCSI host LLD
target/rd: Add DIF protection into rd_execute_rw
target/rd: Add support for protection SGL setup + release
target/rd: Refactor rd_build_device_space + rd_release_device_space
target/file: Add DIF protection support to fd_execute_rw
target/file: Add DIF protection init/format support
...
Lorenzo Pieralisi [Mon, 27 Jan 2014 10:50:37 +0000 (10:50 +0000)]
drivers: bus: fix CCI driver kcalloc call parameters swap
This patch fixes a bug/typo in the CCI driver kcalloc usage
that inadvertently swapped the parameters order in the
kcalloc call and went unnoticed.
Reported-by: Xia Feng <xiafeng@allwinnertech.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Tim Kryger [Tue, 7 Jan 2014 18:53:41 +0000 (10:53 -0800)]
ARM: dts: bcm28155-ap: Fix Card Detection GPIO
The board schematic states that the "SD_CARD_DET_N gets pulled to GND
when card is inserted" so the polarity has been updated to active low.
Polarity is now specified with a GPIO define instead of a magic number.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 31 Jan 2014 23:08:10 +0000 (15:08 -0800)]
Merge tag 'renesas-dt-fixes2-for-v3.14' of git://git./linux/kernel/git/horms/renesas into fixes
Second Round of Renesas ARM Based SoC DT Fixes for v3.14
Correct i2c clock references for r8a7790 (R-Car H2) SoC
The error was introduced in
72197ca7a1cb1cea5 ("ARM: shmobile: r8a7790:
Reference clocks") which is queued up for v3.14.
* tag 'renesas-dt-fixes2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790.dtsi: ficx i2c[0-3] clock reference
Signed-off-by: Olof Johansson <olof@lixom.net>
Fabio Estevam [Sat, 11 Jan 2014 16:16:16 +0000 (14:16 -0200)]
ARM: multi_v7_defconfig: Select CONFIG_AT803X_PHY
Select CONFIG_AT803X_PHY so that we can boot hummingboard via NFS.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Grygorii Strashko [Thu, 9 Jan 2014 14:37:06 +0000 (09:37 -0500)]
ARM: keystone: config: fix build warning when CONFIG_DMADEVICES is not set
Drop automatic selection of TI_EDMA from Keystone Kconfig file,
as it produces build warning in case if CONFIG_DMADEVICES is not set:
warning: (ARCH_KEYSTONE) selects TI_EDMA which has unmet direct dependencies (DMADEVICES && (ARCH_DAVINCI || ARCH_OMAP || ARCH_KEYSTONE))
Instead enable TI EDMA support from defconfig.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Barry Song [Fri, 3 Jan 2014 03:24:13 +0000 (11:24 +0800)]
MAINTAINERS: ARM: SiRF: use regex patterns to involve all SiRF drivers
instead of listing drivers one by one, use regex patterns to involve all
SiRF drivers directly.
this also adds sirf UART and watchdog drivers automatically from:
drivers/tty/serial/sirfsoc_uart.*
drivers/watchdog/sirfsoc_wdt.c
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 31 Jan 2014 22:59:28 +0000 (14:59 -0800)]
Merge tag 'mvebu-fixes-3.13-2' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for v3.13 (incremental #2)
- allow building and booting DT and non-DT plat-orion SoCs
- catch proper return value for kirkwood_pm_init()
- properly check return of of_iomap to solve boot hangs (mirabox, others)
- remove a compile warning on Armada 370 with non-SMP.
* tag 'mvebu-fixes-3.13-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP)
ARM: mvebu: Fix kernel hang in mvebu_soc_id_init() when of_iomap failed
ARM: kirkwood: kirkwood_pm_init() should return void
ARM: orion: provide C-style interrupt handler for MULTI_IRQ_HANDLER
Signed-off-by: Olof Johansson <olof@lixom.net>
Soren Brinkmann [Mon, 2 Dec 2013 18:02:37 +0000 (10:02 -0800)]
ARM: dts: zynq: Add SDHCI nodes
Add nodes for the Arasan SDHCI controller to Zynq dts files.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Rob Herring [Fri, 31 Jan 2014 22:06:30 +0000 (16:06 -0600)]
ARM: hisi: don't select SMP
SMP is a user configurable option, not a hardware feature and should not
be selected.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Stephen Warren [Sat, 25 Jan 2014 03:13:28 +0000 (20:13 -0700)]
ARM: tegra: rebuild tegra_defconfig to add DEBUG_FS
DEBUG_FS used to be selected by COMMON_CLK_DEBUG, which was enabled
by tegra_defconfig. However, this config option no longer exists, so
no longer selects DEBUG_FS, and nothing else selects it either. So,
"make tegra_defconfig" no longer enables DEBUG_FS in .config.
Rebuild tegra_defconfig on top of next-
20140424, while manually
re-enabling DEBUG_FS.
Reasons for removed entries are:
- I2C_MUX: selected by MEDIA_SUBDRV_AUTOSELECT
- DRM_PANEL: selected by DRM_TEGRA
- NEW_LEDS: selected by many things; at least VT
- LEDS_CLASS: selected by many things; at least VT
- LEDS_TRIGGERS: selected by many things; at least VT
- COMMON_CLK_DEBUG: no longer exists
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Stephen Warren [Fri, 20 Dec 2013 20:41:32 +0000 (13:41 -0700)]
ARM: multi_v7: copy most options from tegra_defconfig
multi_v7_defconfig was missing a large number of options that were in
tegra_defconfig. This patch adds them. The changes fall into the
following categories:
* Enable more Tegra SoC options/drivers.
* Enable more drivers for Tegra boards.
* Enable more options that are useful for running distros.
The patch removes a few lines as well, simply because those options are
now selected by something else, and "make savedefconfig" removes them. I
verified that the options appear in .config after
"make multi_v7_defconfig".
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Walleij [Wed, 29 Jan 2014 14:20:15 +0000 (15:20 +0100)]
ARM: iop32x: fix power off handling for the EM7210 board
This board was missed when converting all the others to proper
abstracted GPIO handling. Fix it up the right way by requesting
and driving GPIO line 0 high through gpiolib to power off the
machine.
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Walleij [Fri, 24 Jan 2014 13:04:28 +0000 (14:04 +0100)]
ARM: integrator: restore static map on the CP
Commit
78d1632183454dba46ca8295484a5e7603acdc18 deleted the
static mappings of the core modules, but this static map is
still needed on the Integrator/CP (not the Integrator/AP).
Restore the static map on the Integrator/CP.
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Stephen Boyd [Fri, 17 Jan 2014 01:25:04 +0000 (17:25 -0800)]
ARM: msm_defconfig: Enable MSM clock drivers
This allows us to probe the clock controller devices and boot to a
serial console on all DT enabled MSM platforms.
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Stephen Boyd [Fri, 17 Jan 2014 01:25:03 +0000 (17:25 -0800)]
ARM: dts: msm: Add clock controller nodes and hook into uart
Add the necessary DT nodes to probe the clock controllers on MSM
devices as well as hook up the uart nodes to the clock
controllers. This should allow us to boot to a serial console on
all DT enabled MSM platforms.
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Nishanth Menon [Mon, 20 Jan 2014 20:06:37 +0000 (14:06 -0600)]
ARM: OMAP4+: move errata initialization to omap4_pm_init_early
Move all OMAP4 PM errata initializations to centralized location in
omap4_pm_init_early. This allows for users to utilize the erratas
in various submodules as needed.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Strashko, Grygorii [Tue, 22 Oct 2013 19:07:15 +0000 (22:07 +0300)]
ARM: OMAP4460: cpuidle: Extend PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD on cpuidle
The same workaround as
ff999b8a0983ee15668394ed49e38d3568fc6859
"ARM: OMAP4460: Workaround for ROM bug because of CA9 r2pX GIC ..."
need to be applied not only when system is booting, but when MPUSS hits
OSWR state through CPUIdle too. Without this WA the same issue is
reproduced now on boards PandaES and Tablet/Blaze with SOM OMAP4460
when CONFIG_CPU_IDLE is enabled.
After MPUSS has enterred OSWR and waken up:
- GIC distributor became disabled forever
- scheduling is not performed any more
Cc: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reported-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Oleg Drokin [Fri, 31 Jan 2014 20:41:58 +0000 (15:41 -0500)]
Fix mountpoint reference leakage in linkat
Recent changes to retry on ESTALE in linkat
(commit
442e31ca5a49e398351b2954b51f578353fdf210)
introduced a mountpoint reference leak and a small memory
leak in case a filesystem link operation returns ESTALE
which is pretty normal for distributed filesystems like
lustre, nfs and so on.
Free old_path in such a case.
[AV: there was another missing path_put() nearby - on the previous
goto retry]
Signed-off-by: Oleg Drokin: <green@linuxhacker.ru>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Fri, 31 Jan 2014 22:25:52 +0000 (14:25 -0800)]
Merge tag 'arm64-upstream' of git://git./linux/kernel/git/arm64/linux
Pyll ARM64 patches from Catalin Marinas:
- Build fix with DMA_CMA enabled
- Introduction of PTE_WRITE to distinguish between writable but clean
and truly read-only pages
- FIQs enabling/disabling clean-up (they aren't used on arm64)
- CPU resume fix for the per-cpu offset restoring
- Code comment typos
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: Introduce PTE_WRITE
arm64: mm: Remove PTE_BIT_FUNC macro
arm64: FIQs are unused
arm64: mm: fix the function name in comment of cpu_do_switch_mm
arm64: fix build error if DMA_CMA is enabled
arm64: kernel: fix per-cpu offset restore on resume
arm64: mm: fix the function name in comment of __flush_dcache_area
arm64: mm: use ubfm for dcache_line_size
Linus Torvalds [Fri, 31 Jan 2014 22:24:56 +0000 (14:24 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mattst88/alpha
Pull alpha updates from Matt Turner:
"A pair of changes for alpha. One fixes a networking regression, and
the second adds audit syscall support which will help in supporting
systemd"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
alpha: fix broken network checksum
alpha: Enable system-call auditing support.
Christoph Hellwig [Thu, 30 Jan 2014 07:59:19 +0000 (23:59 -0800)]
hfsplus: use xattr handlers for removexattr
hfsplus was already using the handlers for get and set operations,
and with the removal of can_set_xattr we've now allow operations that
wouldn't otherwise be allowed.
With this we can also centralize the special-casing of the osx.
attrs that don't have prefixes on disk in the osx xattr handlers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Stephan Springl [Thu, 30 Jan 2014 16:56:23 +0000 (17:56 +0100)]
Typo in compat_sys_lseek() declaration
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Andrew Ruder [Thu, 30 Jan 2014 15:26:54 +0000 (09:26 -0600)]
fs/super.c: sync ro remount after blocking writers
Move sync_filesystem() after sb_prepare_remount_readonly(). If writers
sneak in anywhere from sync_filesystem() to sb_prepare_remount_readonly()
it can cause inodes to be dirtied and writeback to occur well after
sys_mount() has completely successfully.
This was spotted by corrupted ubifs filesystems on reboot, but appears
that it can cause issues with any filesystem using writeback.
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
CC: Richard Weinberger <richard@nod.at>
Co-authored-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Jeff Layton [Mon, 27 Jan 2014 18:33:28 +0000 (13:33 -0500)]
vfs: unexport the getname() symbol
Leaving getname() exported when putname() isn't is a bad idea.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Fri, 31 Jan 2014 17:31:14 +0000 (09:31 -0800)]
Merge branch 'v4l_for_linus' of git://git./linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- a new jpeg codec driver for Samsung Exynos (jpeg-hw-exynos4)
- a new dvb frontend for ds2103 chipset (m88ds2103)
- a new sensor driver for Samsung S5K5BAF UXGA (s5k5baf)
- new drivers for R-Car VSP1
- a new radio driver: radio-raremono
- a new tuner driver for ts2022 chipset (m88ts2022)
- the analog part of em28xx is now a separate module that only
load/runs if the device is not a pure digital TV device
- added a staging driver for bcm2048 radio devices
- the omap 2 video driver (omap24xx) was moved to staging. This driver
is for an old hardware and uses a deprecated Kernel internal API. If
nobody cares enough to fix it, it would be removed on a couple Kernel
releases
- the sn9c102 driver was moved to staging. This driver was replaced by
gspca, and disabled on some distros, as almost all devices are known
to work properly with gspca. It should be removed from kernel on a
couple Kernel releases
- lots of driver fixes, improvements and cleanups
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (421 commits)
[media] media: v4l2-dev: fix video device index assignment
[media] rc-core: reuse device numbers
[media] em28xx-cards: properly initialize the device bitmap
[media] Staging: media: Fix line length exceeding 80 characters in as102_drv.c
[media] Staging: media: Fix line length exceeding 80 characters in as102_fe.c
[media] Staging: media: Fix quoted string split across line in as102_fe.c
[media] media: st-rc: Add reset support
[media] m2m-deinterlace: fix allocated struct type
[media] radio-usb-si4713: fix sparse non static symbol warnings
[media] em28xx-audio: remove needless check before usb_free_coherent()
[media] au0828: Fix sparse non static symbol warning
Revert "[media] go7007-usb: only use go->dev after allocated"
[media] em28xx-audio: provide an error code when URB submit fails
[media] em28xx: fix check for audio only usb interfaces when changing the usb alternate setting
[media] em28xx: fix usb alternate setting for analog and digital video endpoints > 0
[media] em28xx: make 'em28xx_ctrl_ops' static
em28xx-alsa: Fix error patch for init/fini
[media] em28xx-audio: flush work at .fini
[media] drxk: remove the option to load firmware asynchronously
[media] em28xx: adjust period size at runtime
...
Linus Torvalds [Fri, 31 Jan 2014 17:23:52 +0000 (09:23 -0800)]
Merge tag 'pm+acpi-3.14-rc1-2' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes and cleanups from Rafael Wysocki:
- ACPI device hotplug fix preventing ACPI drivers from binding to device
objects that acpi_bus_trim() has been called for and the devices
represented by them may not be operational.
- Recent cpufreq changes related to the "boost" (turbo) feature broke
the acpi-cpufreq error code path causing a NULL pointer dereference
to occur on some systems. Fix from Konrad Rzeszutek Wilk.
- The log level of a CPU initialization error message added recently
needs to be reduced, because the particular BIOS issue indicated by
it turns out to be widespread and doesn't really matter for the
majority of systems having it. From Jiang Liu.
- The regulator API needs to be told to stay away from things on systems
with ACPI BIOSes or it may conflict with the BIOS' own handling of
voltage regulators. Fix from Mark Brown that works around a 3.13
regression in lm90 on PCs occuring if the regulator API is enabled.
- Prevent the Exynos4 devfreq driver from being built on multiplatform,
because it depends on things that aren't available during such builds.
From Sachin Kamat.
- Upstream ACPICA doesn't use the bool type as defined in the kernel,
so modify the kernel's ACPICA code to follow the upstream in that
respect (only one variable definition is affected) to reduce
divergences between the two. From Lv Zheng.
- Make the ACPI device PM code use ACPI_COMPANION() instead of its own
routine doing the same thing (and invokng ACPI_COMPANION() in the
process).
- Modify some routines in the ACPI processor driver to follow the
common convention and return negative integers on errors. From
Hanjun Guo.
* tag 'pm+acpi-3.14-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / scan: Clear match_driver flag in acpi_bus_trim()
ACPI / init: Flag use of ACPI and ACPI idioms for power supplies to regulator API
acpi-cpufreq: De-register CPU notifier and free struct msr on error.
ACPICA: Remove bool usage from ACPICA.
PM / devfreq: Disable Exynos4 driver build on multiplatform
ACPI / PM: Use ACPI_COMPANION() to get ACPI companions of devices
ACPI / scan: reduce log level of "ACPI: \_PR_.CPU4: failed to get CPU APIC ID"
ACPI / processor: Return specific error value when mapping lapic id
Mikulas Patocka [Thu, 23 Jan 2014 04:04:33 +0000 (23:04 -0500)]
alpha: fix broken network checksum
The patch
3ddc5b46a8e90f3c9251338b60191d0a804b0d92 breaks networking on
alpha (there is a follow-up fix
5cfe8f1ba5eebe6f4b6e5858cdb1a5be4f3272a6,
but networking is still broken even with the second patch).
The patch
3ddc5b46a8e90f3c9251338b60191d0a804b0d92 makes
csum_partial_copy_from_user check the pointer with access_ok. However,
csum_partial_copy_from_user is called also from csum_partial_copy_nocheck
and csum_partial_copy_nocheck is called on kernel pointers and it is
supposed not to check pointer validity.
This bug results in ssh session hangs if the system is loaded and bulk
data are printed to ssh terminal.
This patch fixes csum_partial_copy_nocheck to call set_fs(KERNEL_DS), so
that access_ok in csum_partial_copy_from_user accepts kernel-space
addresses.
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
蔡正龙 [Fri, 20 Dec 2013 02:04:10 +0000 (10:04 +0800)]
alpha: Enable system-call auditing support.
Signed-off-by: Zhenglong.cai <zhenglong.cai@cs2c.com.cn>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Linus Torvalds [Fri, 31 Jan 2014 17:02:51 +0000 (09:02 -0800)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer/dynticks updates from Ingo Molnar:
"This tree contains misc dynticks updates: a fix and three cleanups"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/nohz: Fix overflow error in scheduler_tick_max_deferment()
nohz_full: fix code style issue of tick_nohz_full_stop_tick
nohz: Get timekeeping max deferment outside jiffies_lock
tick: Rename tick_check_idle() to tick_irq_enter()
Linus Torvalds [Fri, 31 Jan 2014 17:00:44 +0000 (09:00 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"A crash fix and documentation updates"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Make sched_class::get_rr_interval() optional
sched/deadline: Add sched_dl documentation
sched: Fix docbook parameter annotation error in wait.h
Linus Torvalds [Fri, 31 Jan 2014 16:59:46 +0000 (08:59 -0800)]
Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull core debug changes from Ingo Molnar:
"This contains mostly kernel debugging related updates:
- make hung_task detection more configurable to distros
- add final bits for x86 UV NMI debugging, with related KGDB changes
- update the mailing-list of MAINTAINERS entries I'm involved with"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hung_task: Display every hung task warning
sysctl: Add neg_one as a standard constraint
x86/uv/nmi, kgdb/kdb: Fix UV NMI handler when KDB not configured
x86/uv/nmi: Fix Sparse warnings
kgdb/kdb: Fix no KDB config problem
MAINTAINERS: Restore "L: linux-kernel@vger.kernel.org" entries
Stephen Warren [Thu, 30 Jan 2014 18:52:16 +0000 (11:52 -0700)]
ALSA: hda/hdmi - allow PIN_OUT to be dynamically enabled
Commit
384a48d71520 "ALSA: hda: HDMI: Support codecs with fewer cvts
than pins" dynamically enabled each pin widget's PIN_OUT only when the
pin was actively in use. This was required on certain NVIDIA CODECs for
correct operation. Specifically, if multiple pin widgets each had their
mux input select the same audio converter widget and each pin widget had
PIN_OUT enabled, then only one of the pin widgets would actually receive
the audio, and often not the one the user wanted!
However, this apparently broke some Intel systems, and commit
6169b673618b "ALSA: hda - Always turn on pins for HDMI/DP" reverted the
dynamic setting of PIN_OUT. This in turn broke the afore-mentioned NVIDIA
CODECs.
This change supports either dynamic or static handling of PIN_OUT,
selected by a flag set up during CODEC initialization. This flag is
enabled for all recent NVIDIA GPUs.
Reported-by: Uosis <uosisl@gmail.com>
Cc: <stable@vger.kernel.org> # v3.13
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Krzysztof Kozlowski [Thu, 30 Jan 2014 13:51:19 +0000 (14:51 +0100)]
regulator: s2mps11: Fix NULL pointer of_node value when using platform data
When platform_data is used for regulator (of_node of sec-core MFD device
is NULL) the config.of_node for regulator is not initialized. This NULL
value of config.of_node is later stored during regulator_register().
Thus any call by regulator consumers to of_get_regulator() will fail on
of_parse_phandle() returning NULL.
In this case (using platform_data and parent's driver of_node is NULL)
set the config.of_node to reg_node from platform_data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Linus Torvalds [Fri, 31 Jan 2014 16:38:18 +0000 (08:38 -0800)]
Merge tag 'stable/for-linus-3.14-rc0-late-tag' of git://git./linux/kernel/git/xen/tip
Pull Xen bugfixes from Konrad Rzeszutek Wilk:
"Bug-fixes for the new features that were added during this cycle.
There are also two fixes for long-standing issues for which we have a
solution: grant-table operations extra work that was not needed
causing performance issues and the self balloon code was too
aggressive causing OOMs.
Details:
- Xen ARM couldn't use the new FIFO events
- Xen ARM couldn't use the SWIOTLB if compiled as 32-bit with 64-bit PCIe devices.
- Grant table were doing needless M2P operations.
- Ratchet down the self-balloon code so it won't OOM.
- Fix misplaced kfree in Xen PVH error code paths"
* tag 'stable/for-linus-3.14-rc0-late-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pvh: Fix misplaced kfree from xlated_setup_gnttab_pages
drivers: xen: deaggressive selfballoon driver
xen/grant-table: Avoid m2p_override during mapping
xen/gnttab: Use phys_addr_t to describe the grant frame base address
xen: swiotlb: handle sizeof(dma_addr_t) != sizeof(phys_addr_t)
arm/xen: Initialize event channels earlier
Linus Torvalds [Fri, 31 Jan 2014 16:37:32 +0000 (08:37 -0800)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull more KVM updates from Paolo Bonzini:
"Second batch of KVM updates. Some minor x86 fixes, two s390 guest
features that need some handling in the host, and all the PPC changes.
The PPC changes include support for little-endian guests and
enablement for new POWER8 features"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (45 commits)
x86, kvm: correctly access the KVM_CPUID_FEATURES leaf at 0x40000101
x86, kvm: cache the base of the KVM cpuid leaves
kvm: x86: move KVM_CAP_HYPERV_TIME outside #ifdef
KVM: PPC: Book3S PR: Cope with doorbell interrupts
KVM: PPC: Book3S HV: Add software abort codes for transactional memory
KVM: PPC: Book3S HV: Add new state for transactional memory
powerpc/Kconfig: Make TM select VSX and VMX
KVM: PPC: Book3S HV: Basic little-endian guest support
KVM: PPC: Book3S HV: Add support for DABRX register on POWER7
KVM: PPC: Book3S HV: Prepare for host using hypervisor doorbells
KVM: PPC: Book3S HV: Handle new LPCR bits on POWER8
KVM: PPC: Book3S HV: Handle guest using doorbells for IPIs
KVM: PPC: Book3S HV: Consolidate code that checks reason for wake from nap
KVM: PPC: Book3S HV: Implement architecture compatibility modes for POWER8
KVM: PPC: Book3S HV: Add handler for HV facility unavailable
KVM: PPC: Book3S HV: Flush the correct number of TLB sets on POWER8
KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs
KVM: PPC: Book3S HV: Align physical and virtual CPU thread numbers
KVM: PPC: Book3S HV: Don't set DABR on POWER8
kvm/ppc: IRQ disabling cleanup
...
Linus Torvalds [Fri, 31 Jan 2014 16:14:35 +0000 (08:14 -0800)]
Merge tag 'jfs-3.14' of git://github.com/kleikamp/linux-shaggy
Pull jfs fix from David Kleikamp:
"Minor bug fix for linux-3.14"
* tag 'jfs-3.14' of git://github.com/kleikamp/linux-shaggy:
jfs: fix xattr value size overflow in __jfs_setxattr
Sage Weil [Fri, 31 Jan 2014 15:25:25 +0000 (07:25 -0800)]
ceph: fix missing dput in ceph_set_acl
Add matching dput() for d_find_alias(). Move d_find_alias() down a bit
at Julia's suggestion.
[ Introduced by commit
72466d0b92e0: "ceph: fix posix ACL hooks" ]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sachin Prabhu [Fri, 31 Jan 2014 14:27:16 +0000 (14:27 +0000)]
cifs: Fix check for regular file in couldbe_mf_symlink()
MF Symlinks are regular files containing content in a specified format.
The function couldbe_mf_symlink() checks the mode for a set S_IFREG bit
as a test to confirm that it is a regular file. This bit is also set for
other filetypes and simply checking for this bit being set may return
false positives.
We ensure that we are actually checking for a regular file by using the
S_ISREG macro to test instead.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Reported-by: Neil Brown <neilb@suse.de>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Dave Jones [Mon, 27 Jan 2014 15:56:09 +0000 (10:56 -0500)]
xen/pvh: Fix misplaced kfree from xlated_setup_gnttab_pages
Passing a freed 'pages' to free_xenballooned_pages will end badly
on kernels with slub debug enabled.
This looks out of place between the rc assign and the check, but
we do want to kfree pages regardless of which path we take.
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Bob Liu [Wed, 22 Jan 2014 06:57:44 +0000 (14:57 +0800)]
drivers: xen: deaggressive selfballoon driver
Current xen-selfballoon driver is too aggressive which may cause OOM be
triggered more often. Eg. this bug reported by James:
https://lkml.org/lkml/2013/11/21/158
There are two mainly reasons:
1) The original goal_page didn't consider some pages used by kernel space, like
slab pages and pages used by device drivers.
2) The balloon driver may not give back memory to guest OS fast enough when the
workload suddenly aquries a lot of physical memory.
In both cases, the guest OS will suffer from memory pressure and OOM may
be triggered.
The fix is make xen-selfballoon driver not that aggressive by adding extra 10%
of total ram pages to goal_page.
It's more valuable to keep the guest system reliable and response faster than
balloon out these 10% pages to XEN.
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>