drm/i915: Exit cherryview_irq_handler() after one pass

This effectively reverts

commit 8e5fd599eb219f1054e39b40d18b217af669eea9
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date:   Wed Apr 9 13:28:50 2014 +0300

    drm/i915/chv: Make CHV irq handler loop until all interrupts are consumed

as under continuous execlists load we can saturate the IRQ handler,
destablising the tsc clock and triggering the NMI watchdog to declare a hung
CPU.

[  552.756051] clocksource: timekeeping watchdog on CPU0: Marking clocksource 'tsc' as unstable because the skew is too large:
[  552.756080] clocksource:                       'refined-jiffies' wd_now: 10003b480 wd_last: 10003b28c mask: ffffffff
[  552.756091] clocksource:                       'tsc' cs_now: d55d31aa50 cs_last: d17446166c mask: ffffffffffffffff
[  552.756210] clocksource: Switched to clocksource refined-jiffies
[  575.217870] NMI watchdog: Watchdog detected hard LOCKUP on cpu 1
[  575.217893] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.5.0-rc7+ #18
[  575.217905] Hardware name:                  /NUC5CPYB, BIOS PYBSWCEL.86A.0027.2015.0507.1758 05/07/2015
[  575.217915]  0000000000000000 ffff88027fd05bc0 ffffffff81288c6d 0000000000000000
[  575.217935]  0000000000000001 ffff88027fd05be0 ffffffff810e72d1 0000000000000000
[  575.217951]  ffff88027fd05c80 ffff88027fd05c20 ffffffff81114b60 0000000181015f1e
[  575.217967] Call Trace:
[  575.217973]  <NMI>  [<ffffffff81288c6d>] dump_stack+0x4f/0x72
[  575.217994]  [<ffffffff810e72d1>] watchdog_overflow_callback+0x151/0x160
[  575.218003]  [<ffffffff81114b60>] __perf_event_overflow+0xa0/0x1e0
[  575.218016]  [<ffffffff811154c4>] perf_event_overflow+0x14/0x20
[  575.218028]  [<ffffffff8101d2ca>] intel_pmu_handle_irq+0x1da/0x460
[  575.218042]  [<ffffffff814a8aae>] ? poll_idle+0x3e/0x70
[  575.218052]  [<ffffffff814a8aae>] ? poll_idle+0x3e/0x70
[  575.218064]  [<ffffffff81014ae8>] perf_event_nmi_handler+0x28/0x50
[  575.218075]  [<ffffffff81007540>] nmi_handle+0x60/0x130
[  575.218086]  [<ffffffff814a8aae>] ? poll_idle+0x3e/0x70
[  575.218096]  [<ffffffff810079c0>] do_nmi+0x140/0x470
[  575.218108]  [<ffffffff81559ec7>] end_repeat_nmi+0x1a/0x1e
[  575.218119]  [<ffffffff814a8aae>] ? poll_idle+0x3e/0x70
[  575.218129]  [<ffffffff814a8aae>] ? poll_idle+0x3e/0x70
[  575.218139]  [<ffffffff814a8aae>] ? poll_idle+0x3e/0x70
[  575.218148]  <<EOE>>  [<ffffffff814a8353>] cpuidle_enter_state+0xf3/0x2f0
[  575.218164]  [<ffffffff814a8587>] cpuidle_enter+0x17/0x20
[  575.218175]  [<ffffffff810aaa3a>] call_cpuidle+0x2a/0x40
[  575.218185]  [<ffffffff810aade3>] cpu_startup_entry+0x273/0x330
[  575.218196]  [<ffffffff81033a1e>] start_secondary+0x10e/0x130

However, not servicing all available IIR within the handler does hurt the
throughput of pathological nop execbuf by about 20%, with a similar effect
upon the dispatch latency of a series of execbuf.

v2: use do {} while(0) for a smaller patch, and easier to revert again

I have reasonable confidence that we do not miss GT interrupts (as
execlists provides a stress case with a failure mechanism easily
detected by igt), however I have less confidence about all the other
sources of interrupts and worry that may lose a display hotplug
interrupt, for example.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93467
Testcase: igt/gem_exec_nop/basic # requires NMI watchdog
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Antti Koskipää <antti.koskipaa@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457946117-6714-1-git-send-email-chris@chris-wilson.co.uk

drm/i915: Rename __force_wake_get to __force_wake_auto

__force_wake_get() only acquires a temporary wakeref on forcewake that is
automatically released when a timer expires. When reading the code
again, I confused __intel_uncore_forcewake_get() for __force_wake_get()
and to my shame thought I found a bug in unbalanced wake_count handling.

I claim that if the function had been called __force_wake_auto() instead
I would not have embarrassed myself.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458829907-26596-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915: Rename GGTT init functions

Rename and document the GGTT init functions to give a better
idea of the context where they are called from.

i915_gem_gtt_init => i915_ggtt_init_hw
i915_gem_init_global_gtt => i915_gem_init_ggtt
i915_global_gtt_cleanup => i915_ggtt_cleanup_hw

Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458830866-12578-1-git-send-email-joonas.lahtinen@linux.intel.com

drm/i915: BUG_ON when ggtt_view is NULL

Lets BUG_ON and don't bother with a WARN and returning an error, so we can
remove the need to pollute the code with error handling, after all it is
a programmer error to provide NULL view. Also while we're here remove
redundant NULL ggtt_view check.

Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458834860-7898-1-git-send-email-matthew.auld@intel.com

drm/i915: fix deadlock on lid open

commit e2c8b8701e2d moved modeset locking inside resume/suspend
functions, but missed a code path only executed on lid close/open
on older hardware. The result was a deadlock when closing and
opening the lid without suspending on such hardware:

 =============================================
 [ INFO: possible recursive locking detected ]
 4.6.0-rc1 #385 Not tainted
 ---------------------------------------------
 kworker/0:3/88 is trying to acquire lock:
  (&dev->mode_config.mutex){+.+.+.}, at: [<ffffffffa063e6a4>] intel_display_resume+0x4a/0x12f [i915]

 but task is already holding lock:
  (&dev->mode_config.mutex){+.+.+.}, at: [<ffffffffa02d0d4f>] drm_modeset_lock_all+0x3e/0xa6 [drm]

 other info that might help us debug this:
  Possible unsafe locking scenario:

        CPU0
        ----
   lock(&dev->mode_config.mutex);
   lock(&dev->mode_config.mutex);

  *** DEADLOCK ***

  May be due to missing lock nesting notation

 7 locks held by kworker/0:3/88:
  #0:  ("kacpi_notify"){++++.+}, at: [<ffffffff81068dfc>] process_one_work+0x14a/0x50b
  #1:  ((&dpc->work)#2){+.+.+.}, at: [<ffffffff81068dfc>] process_one_work+0x14a/0x50b
  #2:  ((acpi_lid_notifier).rwsem){++++.+}, at: [<ffffffff8106f874>] __blocking_notifier_call_chain+0x34/0x65
  #3:  (&dev_priv->modeset_restore_lock){+.+.+.}, at: [<ffffffffa0664cf6>] intel_lid_notify+0x3c/0xd9 [i915]
  #4:  (&dev->mode_config.mutex){+.+.+.}, at: [<ffffffffa02d0d4f>] drm_modeset_lock_all+0x3e/0xa6 [drm]
  #5:  (crtc_ww_class_acquire){+.+.+.}, at: [<ffffffffa02d0d59>] drm_modeset_lock_all+0x48/0xa6 [drm]
  #6:  (crtc_ww_class_mutex){+.+.+.}, at: [<ffffffffa02d0b2a>] modeset_lock+0x13c/0x1cd [drm]

 stack backtrace:
 CPU: 0 PID: 88 Comm: kworker/0:3 Not tainted 4.6.0-rc1 #385
 Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011
 Workqueue: kacpi_notify acpi_os_execute_deferred
  0000000000000000 ffff88022fd5f990 ffffffff8124af06 ffffffff825b39c0
  ffffffff825b39c0 ffff88022fd5fa60 ffffffff8108f547 ffff88022fd5fa70
  000000008108e817 ffff880230236cc0 0000000000000000 ffffffff825b39c0
 Call Trace:
  [<ffffffff8124af06>] dump_stack+0x67/0x90
  [<ffffffff8108f547>] __lock_acquire+0xdb5/0xf71
  [<ffffffff8108bd2c>] ? look_up_lock_class+0xbe/0x10a
  [<ffffffff8108fae2>] lock_acquire+0x137/0x1cb
  [<ffffffff8108fae2>] ? lock_acquire+0x137/0x1cb
  [<ffffffffa063e6a4>] ? intel_display_resume+0x4a/0x12f [i915]
  [<ffffffff8148202f>] mutex_lock_nested+0x7e/0x3a4
  [<ffffffffa063e6a4>] ? intel_display_resume+0x4a/0x12f [i915]
  [<ffffffffa063e6a4>] ? intel_display_resume+0x4a/0x12f [i915]
  [<ffffffffa02d0b2a>] ? modeset_lock+0x13c/0x1cd [drm]
  [<ffffffffa063e6a4>] intel_display_resume+0x4a/0x12f [i915]
  [<ffffffffa063e6a4>] ? intel_display_resume+0x4a/0x12f [i915]
  [<ffffffffa02d0b2a>] ? modeset_lock+0x13c/0x1cd [drm]
  [<ffffffffa02d0b2a>] ? modeset_lock+0x13c/0x1cd [drm]
  [<ffffffffa02d0bf7>] ? drm_modeset_lock+0x17/0x24 [drm]
  [<ffffffffa02d0c8b>] ? drm_modeset_lock_all_ctx+0x87/0xa1 [drm]
  [<ffffffffa0664d6a>] intel_lid_notify+0xb0/0xd9 [i915]
  [<ffffffff8106f4c6>] notifier_call_chain+0x4a/0x6c
  [<ffffffff8106f88d>] __blocking_notifier_call_chain+0x4d/0x65
  [<ffffffff8106f8b9>] blocking_notifier_call_chain+0x14/0x16
  [<ffffffffa0011215>] acpi_lid_send_state+0x83/0xad [button]
  [<ffffffffa00112a6>] acpi_button_notify+0x41/0x132 [button]
  [<ffffffff812b07df>] acpi_device_notify+0x19/0x1b
  [<ffffffff812c8570>] acpi_ev_notify_dispatch+0x49/0x64
  [<ffffffff812ab9fb>] acpi_os_execute_deferred+0x14/0x20
  [<ffffffff81068f17>] process_one_work+0x265/0x50b
  [<ffffffff810696f5>] worker_thread+0x1fc/0x2dd
  [<ffffffff810694f9>] ? rescuer_thread+0x309/0x309
  [<ffffffff810694f9>] ? rescuer_thread+0x309/0x309
  [<ffffffff8106e2d6>] kthread+0xe0/0xe8
  [<ffffffff8107bc47>] ? local_clock+0x19/0x22
  [<ffffffff81484f42>] ret_from_fork+0x22/0x40
  [<ffffffff8106e1f6>] ? kthread_create_on_node+0x1b5/0x1b5

Fixes: e2c8b8701e2d ("drm/i915: Use atomic helpers for suspend, v2.")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459328913-13719-1-git-send-email-bjorn@mork.no

drm/i915: Update DRIVER_DATE to 20160330

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Call intel_dp_mst_resume() before resuming displays

Since we need MST devices ready before we try to resume displays,
calling this after intel_display_resume() can result in some issues with
various laptop docks where the monitor won't turn back on after
suspending the system.

This order was originally changed in

commit e7d6f7d70829 ("drm/i915: resume MST after reading back hw state")

In order to fix some unclaimed register errors, however the actual cause
of those has since been fixed.

CC: stable@vger.kernel.org
Signed-off-by: Lyude <cpaul@redhat.com>
[danvet: Resolve conflicts with locking changes.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Fix races on fbdev

The ->lastclose callback invokes intel_fbdev_restore_mode() and has
been witnessed to run before intel_fbdev_initial_config_async()
has finished.

We might likewise receive hotplug events before we've had a chance to
fully set up the fbdev.

Fix by waiting for the asynchronous thread to finish.

v2:
An async_synchronize_full() was also added to intel_fbdev_set_suspend()
in v1 which turned out to be entirely gratuitous. It caused a deadlock
on suspend (discovered by CI, thanks to Damien Lespiau and Tomi Sarvela
for CI support) and was unnecessary since a device is never suspended
until its ->probe callback (and all asynchronous tasks it scheduled)
have finished. See dpm_prepare(), which calls wait_for_device_probe(),
which calls async_synchronize_full().

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93580
Reported-by: Gustav Fägerlind <gustav.fagerlind@gmail.com>
Reported-by: "Li, Weinan Z" <weinan.z.li@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160309115147.67B2B6E0D3@gabe.freedesktop.org

drm/i915: remove unused dev_priv->render_reclock_avail

Set from VBT, but never used. Good riddance.

Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458834623-8734-5-git-send-email-jani.nikula@intel.com

drm/i915: move sdvo mappings to vbt data

Move all data initialized from VBT under dev_priv->vbt. No functional
changes.

Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458834623-8734-4-git-send-email-jani.nikula@intel.com

drm/i915: move edp low vswing config to vbt data

Move all data initialized from VBT under dev_priv->vbt. No functional
changes.

Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458834623-8734-3-git-send-email-jani.nikula@intel.com

drm/i915: use a substruct in vbt data for edp

Housekeeping, similar to psr, backlight, and dsi. No functional changes.

Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458834623-8734-2-git-send-email-jani.nikula@intel.com

drm/i915: replace for_each_engine()

Having provided for_each_engine_id() for cases where the third (id)
argument is useful, we can now replace all the remaining instances with
a simpler version that takes only two parameters. In many cases, this
also allows the elimination of the local variable used in the iterator
(usually 'i').

v2:
    s/dev_priv/(dev_priv__)/ in body of for_each_engine_masked() [Chris Wilson]

Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458757194-17783-2-git-send-email-david.s.gordon@intel.com

drm/i915: introduce for_each_engine_id()

Equivalent to the existing for_each_engine() macro, this will replace
the latter wherever the third argument *is* actually wanted (in most
places, it is not used). The third argument is renamed to emphasise
that it is an engine id (type enum intel_engine_id). All the callers of
the macro that actually need the third argument are updated to use this
version, and the argument (generally 'i') is also updated to be 'id'.
Other callers (where the third argument is unused) are untouched for
now; they will be updated in the next patch.

Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/bxt: Fix DSI HW state readout

Currently the machine hangs during booting while accessing the
BXT_MIPI_PORT_CTRL register during pipe HW state readout. After some
experimentation I found that the hang is caused by the DSI PLL being
disabled, or it being enabled but with an incorrect divider
configuration. Enabling the PLL got rid of the boot problem, so fix
this by checking the PLL enabled state/configuration before attempting
to read out the HW state.

The DSI_PLL_ENABLE register is in the always-on power well, while the
BXT_DSI_PLL_CTL is in power well 0. This isn't exactly matched by the
transcoder power domain, but what we really need is just a runtime PM
reference, which is provided by any power domain.

Ville also found this dependency specified in BSpec, so I added a
reference to that too.

v2:
- Make sure we hold a power reference while accessing the PLL registers.
v3: (Jani)
- Simplify check in bxt_get_dsi_transcoder_state()
- Add comment explaining why we check for valid dividers in
  bxt_dsi_pll_is_enabled()

CC: Shashank Sharma <shashank.sharma@intel.com>
CC: Uma Shankar <uma.shankar@intel.com>
CC: Jani Nikula <jani.nikula@intel.com>
Fixes: c6c794a2fc5e ("drm/i915/bxt: Initialize MIPI DSI for BXT")
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458816100-31269-1-git-send-email-imre.deak@intel.com

drm/i915: Remove vblank wait from hsw_enable_ips, v2.

intel_post_plane_update did an extra vblank wait that's no longer needed when enabling ips.

Changes since v1:
- Add comment explaining why vblank wait is performed. (Paulo)

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/56F29B28.5070804@linux.intel.com

drm/i915: Tidy aliasing_gtt_bind_vma()

In commit 0a878716265e9af9f697264dc2e858fcc060d833
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Thu Oct 15 14:23:01 2015 +0200

    drm/i915: restore ggtt double-bind avoidance

we wrote the ggtt_bind_vma() observing a number of cleanups we could do
over the template of aliasing_gtt_bind_vma(). Now let's apply the
cleanups we made there back to the original. The essence is to avoid
redundant variables and assignements, and by doing so make the code
easier to read.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1448015238-24639-1-git-send-email-chris@chris-wilson.co.uk

drm/i915: Split PNV version of crtc_compute_clock()

Split a pnv_crtc_compute_clock(), so the differences between platforms
become more obvious.

With this, there are no more users of intel_limit() or the ->find_dpll()
hook, so get rid of them.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-16-git-send-email-ander.conselvan.de.oliveira@intel.com

drm/i915: Split g4x_crtc_compute_clock()

Split a G4X specific version from i9xx_crtc_compute_clock(). With this
the differences between platforms become more obvious.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-15-git-send-email-ander.conselvan.de.oliveira@intel.com

drm/i915: Split i8xx_crtc_compute_clock()

Split a GEN2 specific version from i9xx_crtc_compute_clock(). With this
there is no need for i9xx_get_refclk() anymore, and the differences
between platforms become more obvious.

v2: Use i8xx as prefix instead of gen2. (Ville and Daniel)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458653723-17951-1-git-send-email-ander.conselvan.de.oliveira@intel.com

drm/i915: Split CHV and VLV specific crtc_compute_clock() hooks

In order for VLV and CHV to use i9xx_crtc_compute_clocks(), a number
of if ladders is necessary: one for setting the find_dpll() hook, one
for choosing the limits struct, one for choosing the right compute dpll
function and one for initializing the crtc_compute_clock() hook.

By extracting a platform specific implementation for each platform, the
number of if-ladders is reduced to one.

While at it also clean up bxt_find_best_dpll() which depends on some of
the CHV code.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-13-git-send-email-ander.conselvan.de.oliveira@intel.com

drm/i915: Merge ironlake_compute_clocks() and ironlake_crtc_compute_clock()

Merge ironlake_compute_clocks() into ironlake_crtc_compute_clock() so
the clock computation logic is all in one place. The resulting function
is still quite simple. Follow up patches will make the similar code for
GMCH platforms look similar.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-12-git-send-email-ander.conselvan.de.oliveira@intel.com

drm/i915: Move fp divisor calculation into ironlake_compute_dpll()

Follow what is done in i8xx_compute_dpll() and i9xx_compute_dpll() and
move the lower level details of setting crtc_state->dpll_hw_state into
the _compute_dpll() function.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-11-git-send-email-ander.conselvan.de.oliveira@intel.com

drm/i915: Pass crtc_state->dpll directly to ->find_dpll()

When calculating clocks, just pass a pointer to crtc_state->dpll
directly to the find_dpll() hook. Back when this was introduced in
commit f47709a9502f3 ("drm/i915: create pipe_config->dpll for clock
state") there was no staged crtc config or atomic crtc state, so it was
possible to overwrite the current configuration on error. That hasn't
been the case for a while now, so finally make it "disappear".

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-10-git-send-email-ander.conselvan.de.oliveira@intel.com

drm/i915: Simplify ironlake_crtc_compute_clock() CPU eDP case

None of the code in ironlake_crtc_compute_clock() is relevant for CPU
eDP. The CPU eDP PLL is turned on and off in ironlake_edp_pll_{on,off}
from the DP code and that doesn't depend on the crtc_state->dpll values,
so just return early in that case.

v2: Rebase without patch that drops lvds downclock code. (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-9-git-send-email-ander.conselvan.de.oliveira@intel.com

drm/i915: Remove PCH type checks from ironlake_crtc_compute_clock()

The checks were added in commit 5dc5298bb3e5 ("drm/i915: add proper
CPU/PCH checks to crtc_mode_set functions") in a time when there was
doubts on what PCHs would be supported by HSW. There are similar checks
for PCH type in intel_detect_pch() and the function pointers are
initialized based on platform/pch information, so the removed WARN can't
ever be reached.

v2: Rebase without patch that drops lvds downclock code. (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-8-git-send-email-ander.conselvan.de.oliveira@intel.com

drm/i915: Don't calculate a new clock in ILK+ code if it is already set

Remove the clock calculation from ironlake_crtc_compute_clock() when the
encoder compute_config() already set one. The value was just thrown away
in that case.

Note that the previously set clock is not validated against the limits
anymore. That is ok since the fixed clocks from DP and SDVO are within
the supported range, so the call to ironlake_compute_clocks() would
never fail in that case.

v2: Add note about not checking fixed clocks agains limits. (Maarten)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-7-git-send-email-ander.conselvan.de.oliveira@intel.com

drm/i915: Simplify ironlake reduced clock logic a bit

Check has_reduced_clock only once when setting dpll_hw_state, making the
code slightly more readable.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-6-git-send-email-ander.conselvan.de.oliveira@intel.com

drm/i915: Call g4x_find_best_dpll() directly from ILK+ code

The call to dev_priv->display.find_dpll() is already in platform
specific code, so avoid the extra detour.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-5-git-send-email-ander.conselvan.de.oliveira@intel.com

drm/i915: Fold intel_ironlake_limit() into clock computation function

The function intel_ironlake_limit() is only called by the crtc compute
clock path. By merging it into ironlake_compute_clocks(), the code gets
clearer, since there's no more if-ladders to follow.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-4-git-send-email-ander.conselvan.de.oliveira@intel.com

drm/i915: Merge ironlake_get_refclk() into its only caller

A previous patch made ironlake_get_refclk() very simple, so merge
it into its only caller.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-3-git-send-email-ander.conselvan.de.oliveira@intel.com

drm/i915: Remove checks for cloned config with LVDS in dpll code

LVDS is not cloneable, so the check is unnecessary. Removing it makes
the code neater.

v2: Remove checks from GMCH code too, not only ILK+. (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-2-git-send-email-ander.conselvan.de.oliveira@intel.com

drm/i915: Wait for vblank in i9xx_disable_crtc() for gen 2 only

The wait for other gens was added in commit 564ed191f5d8 ("drm/i915:
gmch: fix stuck primary plane due to memory self-refresh mode") since
that's necessary when disabling cxsr. However, cxsr disabling was later
moved to intel_pre_disable_primary() in commit 87d4300a7dbc ("drm/i915:
Move intel_(pre_disable/post_enable)_primary to intel_display.c, and use
it there.") and that function got its own vblank wait for cxsr in commit
262cd2e154c2 ("drm/i915: CHV DDR DVFS support and another watermark
rewrite"). So remove the extra vblank wait from i9xx_crtc_distable().

Cc: Kalyan Kondapally <kalyan.kondapally@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1458634284-6080-1-git-send-email-ander.conselvan.de.oliveira@intel.com

drm/i915: Fix use after free when printing load failure

Commit d15d7538c6d2 ("drm/i915: Tune down init error message due
to failure injection") added i915_load_error message to failure
path on device initialization. The message is printed
after the device is freed. And as the message printing helper
uses the device structure, this leads to use after free.

Spotted by Kasan.

Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458721906-10625-1-git-send-email-mika.kuoppala@intel.com

drm/i915/bxt: Initialize MIPI DSI for BXT

This patch contains following changes:
1. Add BXT MIPI display address base.
2. Call dsi_init from display_setup function.

v2: Rebased on latest nightly branch

v3 by Jani: init dsi after ddi

Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458640910-5338-1-git-send-email-jani.nikula@intel.com

drm/i915: Make __i915_printk debug output behave the same as DRM_DEBUG_DRIVER

Joonas and Daniel remarked that our debugging output should stay compatible
with the core DRM's debug facility. The recently added __i915_printk() would
output debug messages even if debugging is completely disabled via the
drm.debug option. To fix this make __i915_printk behave the same as
DRM_DEBUG_DRIVER in this case.

CC: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458572937-21712-1-git-send-email-imre.deak@intel.com

drm/i915: Wait until after wm optimization to drop runtime PM reference

At the end of an atomic commit, we currently wait for vblanks to
complete, call put() on the various runtime PM references, and then try
to optimize our watermarks (on platforms that need two-step watermark
programming).  This can lead to watermark registers being programmed
while the power well is powered down.  We need to wait until after
watermark optimization is complete before dropping our runtime power
references.

Note that in the future the watermark optimization is probably going to
move to an asynchronous workqueue task that happens at some arbitrary
point after vblank.  When we make that change, we'll no longer
necessarily be operating under the power reference held here, so we'll
need to wrap the watermark register programmin in a call to
intel_runtime_pm_get_if_in_use() or similar.

Cc: arun.siluvery@linux.intel.com
Cc: ville.syrjala@linux.intel.com
Cc: maarten.lankhorst@linux.intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94349
Fixes: ed4a6a7ca853 ("drm/i915: Add two-stage ILK-style watermark programming (v11)")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457135979-23727-1-git-send-email-matthew.d.roper@intel.com

drm/i915/tdr: Prepare error handler to accept mask of hung engines

In preparation for engine reset, the wedged argument of i915_handle_error()
is extended to reflect as a mask of engines that are hung. This is further
passed down to error state capture functions which are also updated.

Engine reset recovery mechanism uses this mask and schedules recovery work
for those particular engines.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458331676-567-3-git-send-email-arun.siluvery@linux.intel.com

drm/i915/tdr: Initialize hangcheck struct for each engine

Initialize hangcheck struct during driver load. Since we do the same after
recovering from a reset, this is extracted into a helper function.

v2: remove redundant hangcheck init during load as this is done when
engines are initialized (Chris)

Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458577619-12006-1-git-send-email-arun.siluvery@linux.intel.com

drm/i915: Implement color management on chv

Patch based on a previous series by Shashank Sharma.

v2: Update contributors

v3: Refactor degamma/gamma LUTs load into a single function

v4: Remove unused variable

Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Kumar, Kiran S <kiran.s.kumar@intel.com>
Signed-off-by: Kausal Malladi <kausalmalladi@gmail.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125837-2576-5-git-send-email-lionel.g.landwerlin@intel.com

drm/i915: Implement color management on bdw/skl/bxt/kbl

Patch based on a previous series by Shashank Sharma.

v2: Do not read GAMMA_MODE register to figure what mode we're in

v3: Program PREC_PAL_GC_MAX to clamp pixel values > 1.0

    Add documentation on how the Broadcast RGB property is affected by CTM

v4: Update contributors

v5: Refactor degamma/gamma LUTs load into a single function

v6: Fix missing intel_crtc variable (bisect issue)

v7: Fix & simplify limited range matrix multiplication (Matt Roper's
    comment)

Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Kumar, Kiran S <kiran.s.kumar@intel.com>
Signed-off-by: Kausal Malladi <kausalmalladi@gmail.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Acknowledged-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125837-2576-4-git-send-email-lionel.g.landwerlin@intel.com

drm/i915: Do not read GAMMA_MODE register

Implement Daniel Stone's recommendation to not read registers to infer
the hardware's state.

v2: Read GAMMA_MODE register value at init (Matt Roper's comment)

v3: Read GAMMA_MODE register in intel_modeset_readout_hw_state along
    with other registers (Matt Roper's comment).

v4: Mask GAMMA_MODE register with interesting bits when reading

Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125837-2576-3-git-send-email-lionel.g.landwerlin@intel.com

drm/i915: Extract out gamma table and CSC to their own file

The moves a couple of functions programming the gamma LUT and CSC
units into their own file.

On generations prior to Haswell there is only a gamma LUT. From
haswell on there is also a new enhanced color correction unit that
isn't used yet. This is why we need to set the GAMMA_MODE register,
either we're using the legacy 8bits LUT or enhanced LUTs (of 10 or
12bits).

The CSC unit is only available from Haswell on.

We also need to make a special case for CherryView which is recognized
as a gen 8 but doesn't have the same enhanced color correction unit
from Haswell on.

v2: Fix access to GAMMA_MODE register on older generations than
    Haswell (from Matt Roper's comments)

Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1458125837-2576-2-git-send-email-lionel.g.landwerlin@intel.com

drm/i915/bxt: allow dsi on any pipe

BXT isn't as limited as BYT and CHT regarding DSI pipes and ports.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/0375f1e237092d0ae3f39ecfc5702024918acbfd.1458313400.git.jani.nikula@intel.com

drm/i915/dsi: use the BIT macro for clarity

No functional changes.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/9115c0a80ad57075700e006db965dd31cc4358fc.1458313400.git.jani.nikula@intel.com

drm/i915/bxt: add dsi transcoders

The BXT display connections have DSI transcoders A and C that can be
muxed to any pipe, not unlike the eDP transcoder. Add the notion of DSI
transcoders.

The "normal" transcoders A, B and C are not used with BXT DSI, so care
must be taken to avoid accessing those registers with DSI transcoders in
the hardware state readout, modeset, and generally everywhere.

v2: addressing comments by Ville:
 - rename the dsi get config function to hsw_get_dsi_transcoder_state
 - rebase onto the higher level split of pipe/transcoder functions
 - use more has_dsi_encoder as we can now because of the above,
   with no need to look at the transcoder so much
 - rename IS_DSI_TRANSCODER to transcoder_is_dsi
 - use the above a bit more instead of comparing to < TRANSCODER_EDP

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/299740536b7941e31b2744f3ce34f7afe936a771.1458313400.git.jani.nikula@intel.com

drm/i915: abstract get config for cpu transcoder

Makes it neater to add the same for DSI transcoder. No functional
changes.

v2: rename to hsw_get_transcoder_state and add a comment about grabbing
    power reference (Ville)

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/c473a73d69dcd61584419d85ff7908a8717b0594.1458313400.git.jani.nikula@intel.com

drm/i915: split set pipeconf to pipeconf, pipemisc, pipe_gamma

Prep work for DSI transcoders. No functional changes.

v2: call split functions at a higher level (Ville)

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/981252d5d5f82d009d73e1b2ae93d9ab7bee8de8.1458313400.git.jani.nikula@intel.com

drm/i915: split get/set pipe timings to timings and src size

Prep work for DSI transcoders. No functional changes.

v2: call split functions at a higher level (Ville)

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/8d67a05eb869a7b0c4ee17c2d3b0b029de34851c.1458313400.git.jani.nikula@intel.com

drm/i915: add another virtual PCH bridge for passthrough support

Some configs use the P2X type but some use a P3X type PCH, so add that
to the detect_pch function so things work correctly.

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Allen Kay <allen.m.kay@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1458160290-16710-1-git-send-email-jbarnes@virtuousgeek.org

drm/i915: Bump command parser version for new whitelisted registers

Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1457335830-30923-6-git-send-email-jordan.l.justen@intel.com

drm/i915: Add Haswell CS GPR registers to whitelist

This is needed for the Mesa Vulkan driver on Haswell.

Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1457335830-30923-5-git-send-email-jordan.l.justen@intel.com

drm/i915: Move Haswell registers to separate whitelist table

Now that we can whitelist registers only on Haswell, move HSW_SCRATCH1
and HSW_ROW_CHICKEN3 into a separate Haswell only table.

Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Cc: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1457335830-30923-4-git-send-email-jordan.l.justen@intel.com

drm/i915: Use an array of register tables in command parser

For Haswell, we will want another table of registers while retaining
the large common table of whitelisted registers shared by all gen7
devices.

Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
[danvet: Pipe patch through sed -e 's/\<ring\>/engine/g' to make it
apply.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Add TIMESTAMP to register whitelist

This is needed for the Mesa Vulkan driver on Haswell.

Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Cc: Kristian Høgsberg <krh@bitplanet.net>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1457335830-30923-2-git-send-email-jordan.l.justen@intel.com

drm/i915: Tune down init error message due to failure injection

Atm, in case failure injection forces an error the subsequent "*ERROR*
failed to init modeset" error message will make automated tests (CI)
report this event as a breakage even though the event is expected. To
fix this print the error message with debug log level in this case.

While at it print the error message for any init failure and change it
to
"""
Device initialization failed (errno)
Please file a bug at https://bugs.freedesktop.org/enter_bug.cgi?product=DRI
against DRM/Intel providing the dmesg log by booting with drm.debug=0xf
"""
and export a helper printing error messages using this same format.
A follow-up patch will convert all uses of DRM_ERROR reporting a user
facing problem to use this new helper instead.

v2:
- Include the problematic error message in the commit log, add a
  request to file an fdo bug to the message (Chris)
v3:
- Include the new error message too in the commit log, make the
  fdo link more precise and print part of the message with info log
  level (Chris)
v4: (Chris)
- Use dev_printk instead of DRM_ERROR/INFO and use NOTICE instead of
  INFO loglevel
- Export a helper for printing user facing error messages
v5:
- Keep the DRM_ERROR message prefix used by piglit-igt/CI to filter
  relevant dmesg lines
- Use dev_notice(), instead of dev_printk(KERN_NOTICE,...)
v6:
- Print the fdo bug link only once (Chris)

CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458290770-15480-1-git-send-email-imre.deak@intel.com

drm/i915: Codify our assumption that the Global GTT is <= 4GiB

Throughout the code base, we use u32 for offsets into the global GTT. If
we ever see any hardware with a larger GGTT, then we run the real risk
of silent corruption. So test for our assumption up front so that we
have a nice reminder should the time come when it fails.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
[Rebased and changed 1ull -> 1ULL, cut 80 char line]
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458290579-27783-1-git-send-email-joonas.lahtinen@linux.intel.com

drm/i915/gtt: Clean up GGTT probing code

Use less pointers with the probing code, making it much less confusing
to read.

Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915: Rename dev_priv->gtt to dev_priv->ggtt

Refer to Global GTT consistently as GGTT, thus rename dev_priv->gtt
to dev_priv->ggtt and struct i915_gtt to struct i915_ggtt.

Fix a couple of whitespace problems while at it.

v2:
- Fix a typo in commit message.

Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915/gtt: Reference mappable_end variable from pointer

Reference variable value from pointer, not assumed pointer destination.

Since:

commit c44ef60e437019b8ca1dab8b4d2e8761fd4ce1e9
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date:   Thu Jun 25 18:35:05 2015 +0300

    drm/i915/gtt: Allow >= 4GB sizes for vm.

Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915/gen9: add WaClearFlowControlGpgpuContextSave

This allows writes to EU flow control registers. Together
with SIP code from the user-mode driver this resolves a
hang seen in some pre-emption scenarios. Note that this
patch is just the kernel mode part of this workaround.

v2. Oops, add FLOW_CONTROL_ENABLE macro to i915_reg.h.

Signed-off-by: Tim Gore <tim.gore@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458144826-17269-1-git-send-email-tim.gore@intel.com

drm/i915: Move CSB MMIO reads out of the execlists lock

By reading the CSB (slow MMIO accesses) into a temporary local
buffer we can decrease the duration of holding the execlist
lock.

Main advantage is that during heavy batch buffer submission we
reduce the execlist lock contention, which should decrease the
latency and CPU usage between the submitting userspace process
and interrupt handling.

Downside is that we need to grab and relase the forcewake twice,
but as the below numbers will show this is completely hidden
by the primary gains.

Testing with "gem_latency -n 100" (submit batch buffers with a
hundred nops each) shows more than doubling of the throughput
and more than halving of the dispatch latency, overall latency
and CPU time spend in the submitting process.

Submitting empty batches ("gem_latency -n 0") does not seem
significantly affected by this change with throughput and CPU
time improving by half a percent, and overall latency worsening
by the same amount.

Above tests were done in a hundred runs on a big core Broadwell.

v2:
  * Overflow protection to local CSB buffer.
  * Use closer dev_priv in execlists_submit_requests. (Chris Wilson)

v3: Rebase.

v4: Added commend about irq needed to be disabled in
    execlists_submit_request. (Chris Wilson)

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilsno <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458219586-20452-1-git-send-email-tvrtko.ursulin@linux.intel.com

drm/i915: Use shorter route to dev_private where possible

Where we have a request we can use req->i915 directly instead
of going through the engine and device. Coccinelle script:

@@
function f;
identifier r;
@@
f(..., struct drm_i915_gem_request *r, ...)
{
...
- engine->dev->dev_private
+ r->i915
...
}
@@
struct drm_i915_gem_request *req;
@@
(
  req->
- engine->dev->dev_private
+ i915
)

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458219850-21007-1-git-send-email-tvrtko.ursulin@linux.intel.com

drm/i915: Remove unused variable in i915_gem_request_add_to_client

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Add fault injection support

Add support for forcing an error at selected places in the driver. As an
example add 4 options to fail during driver loading.

Requested by Chris.

v2:
- Add fault point for modeset initialization
- Print debug message when injecting an error
v3:
- Rename inject_fault to inject_load_failure, rename the related macros
  and helper accordingly (Chris)
- Use a counter instead of a mask to identify the failure point (Daniel)
- Mark the module option as _unsafe and keep i915_params ordered (Joonas)
v4:
- Rebase on latest -nightly
v5:
- Use DRM_INFO instead of DRM_DEBUG_DRIVER, making it clearer in CI reports
  that a following error message is expected (IRC r-b from Chris on v5)

CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
CC: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Fix power domain HW state cleanup on error path

Move the cleanup of the power domain HW state on the error path to the
same function where the corresponding init call was called from. I
noticed this problem when loading the module with load failure injection
enabled, making i915_load_modeset_init() fail.

CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-19-git-send-email-imre.deak@intel.com

drm/i915: Split out load time interface registration

According to the new init phases scheme we should register the device
making it available via some kernel internal or user space interface as
the last step in the init sequence, so move the corresponding code to a
separate function.

Also add a TODO comment about code that still needs to be moved around
to one of the init phases functions depending on what the role and effect
of that code is.

No functional change, except for the reordering of the unload time
unregistration steps of sysfs wrt. acpi and opregion.

Suggested by Chris.

v3:
- rename i915_driver_init_register to i915_driver_init_frameworks
  (Chris)
- rename i915_driver_init_frameworks to i915_driver_register (Daniel)

CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-18-git-send-email-imre.deak@intel.com

drm/i915: Split out load time HW initialization

According to the new init phases scheme we should have a definite step
in the init sequence where we setup things requiring accessing the
device, so move the corresponding code to separate function. The steps
in this init phase should avoid exposing the driver via some interface,
which is done in the last registration init phase. This changae also
has the benefit of making the error path cleaner both in the new
function and i915_driver_load()/unload().

No functional change.

Suggested by Chris.

CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-17-git-send-email-imre.deak@intel.com

drm/i915: Split out load time MMIO initialization

According to the new init phases scheme we should have a definite step
in the init sequence where MMIO access is setup, so move the
corresponding code to a separate function. This also has the benefit of
making the error path cleaner both in the new function and in
i915_driver_load()/unload().

No functional change.

Suggested by Chris.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-16-git-send-email-imre.deak@intel.com

drm/i915: Split out load time early initialization

According to the new init phases scheme we should initialize "SW-only"
state not requiring accessing the device as the very first step, so that
the reasoning about dependencies of later steps becomes easier. So move
these init steps into a separate function. This also has the benefit of
making the error path cleaner both in the new function and int
i915_driver_load()/unload().

No functional change.

Suggested by Chris.

CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-15-git-send-email-imre.deak@intel.com

drm/i915: Move unload time opregion unregistration earlier

Move the opregion unregistration earlier to match its corresponding
registration order.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-14-git-send-email-imre.deak@intel.com

drm/i915: Move unload time GTT, MSI IRQ cleanup later

Move the GTT,MSI IRQ cleanup later so that it matches their
corresponding init order. Also fix the order of these calls wrt. each
other to match their corresponding init order.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-13-git-send-email-imre.deak@intel.com

drm/i915: Move unload time display power domain uninit later

Move the power domain uninitialization later so that it matches its
corresponding init order. Since we access the HW during the later
unitialization steps keep a wake reference until after the last such
step.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-12-git-send-email-imre.deak@intel.com

drm/i915: Move load time audio component registration earlier

We should register all the interfaces before we enable runtime PM.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-11-git-send-email-imre.deak@intel.com

drm/i915: Move load time shrinker registration later

According to the new init phases scheme we should register the driver
with frameworks/userspace only one the device is setup fully. So move
the shrinker registration later accordingly.

Also fix the shrinker unregistration order wrt. the acpi unregistration
to fix the corresponding init order.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-10-git-send-email-imre.deak@intel.com

drm/i915: Move load time runtime PM get later

We require the device to be powered only before accessing it, so we can
move this call later.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-9-git-send-email-imre.deak@intel.com

drm/i915: Move load time gem_load_init earlier

The only steps requiring device access is the fence and swizzling
initialization, so split these out keeping them in their current place
and move the rest of init steps earlier.

v2-v3:
- unchanged
v4:
- move call to i915_gem_detect_bit_6_swizzle() to
  i915_gem_load_init_fences() and preserve the original order of
  the detection of HW fence capailities wrt. swizzling (Chris)

CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458132843-21860-1-git-send-email-imre.deak@intel.com

drm/i915: Move load time runtime device info init earlier

This init step accesses the device, but doesn't have any device
specific side effect. It also sets up some platform specific
attributes that may be required early, so move it earlier.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-7-git-send-email-imre.deak@intel.com

drm/i915: Move load time init of clock gating hooks earlier

Split out the part initing the clock gating hooks and move it earlier.
Add a new NOP hook for platforms without the need to apply clockgating
or workaround settings, so that the hook can be called unconditionally.
Also add a WARN for future platforms that forget to add a hook.

The rest of the hooks in intel_init_pm() should be inited in the same
way, but atm some of the hooks are set only conditionally, so before
doing this we need to make the setup unconditional and use instead some
flags.

v2:
- add a NOP hook and WARN if no hook is set for the platform (Chris)
- use the term hook instead of callback for these functions (Jani)
v3:
- remove the GEN4() check it's already covered by earlier platform
  checks (Chris)

CC: Jani Nikula <jani.nikula@intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-6-git-send-email-imre.deak@intel.com

drm/i915: Move load time init of display/audio hooks earlier

All of this is SW only initialization so we can move them earlier. Move
the mutex init where the rest of the locks are inited. While at it also
convert dev to dev_priv.

v2:
- use the term hook instead of callback for these functions (Jani)

CC: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-5-git-send-email-imre.deak@intel.com

drm/i915: Move load time IRQ SW init earlier

Most of the IRQ init is setting up hooks so move that part earlier.
Leave the pm_qos_add_request() call in place.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-4-git-send-email-imre.deak@intel.com

drm/i915: Move load time PCH detect, DPIO, power domain SW init earlier

These are all SW only init steps not accessing the device and they only
need the platform identification macros to work, which are already
available earlier, so move these init steps earlier.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-3-git-send-email-imre.deak@intel.com

Fix MCHBAR cleanup on the driver init error path

MCHBAR is cleaned up in i915_mmio_cleanup(), so the separate call in
i915_driver_load() is incorrect.

CC: David Weinehall <david.weinehall@intel.com>
Fixes: ad5c3d3ffbb2 ("drm/i915: Move MCHBAR setup earlier during init")
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-2-git-send-email-imre.deak@intel.com

drm/i915: Modify reset func to handle per engine resets

In full gpu reset we prime all engines and reset domains corresponding to
each engine. Per engine reset is just a special case of this process
wherein only a single engine is reset. This change is aimed to modify
relevant functions to achieve this. There are some other steps we carry out
in case of engine reset which are addressed in later patches.

Reset func now accepts a mask of all engines that need to be reset. Where
per engine resets are supported, error handler populates the mask
accordingly otherwise all engines are specified.

v2: ALL_ENGINES mask fixup, better for_each_ring_masked (Chris)
v3: Whitespace fixes (Chris)
v4: Rebase due to s/ring/engine

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458143640-20563-1-git-send-email-mika.kuoppala@intel.com

drm/i915: hide away VBT private data in a separate header

We've been accumulating code across the driver that depends on the VBT
specific structures and defines. The VBT is an uncontrollable
beast. Encourage encapsulation of the VBT data by hiding the structures
and defines in a private header only to be included from intel_bios.c.

Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125015-7931-7-git-send-email-jani.nikula@intel.com

drm/i915: fix sparse warning for using false as NULL

drivers/gpu/drm/i915/intel_dpll_mgr.c:1200:32: warning: Using plain integer as NULL pointer

Fixes: 304b65cbdc8d ("drm/i915: Move SKL/KLB pll selection logic to intel_dpll_mgr.c")
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458144418-20046-1-git-send-email-jani.nikula@intel.com

drm/i915: Move pll power state to crtc power domains.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457944075-14123-4-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>

drm/i915: Perform dpll commit first, v2.

Warn for the wrong mask in enable only. Disable will have the wrong mask now
because the new state is committed before disabling the old state.

Changes since v1:
- Use crtc_mask (Durgadoss)
- Rebase.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457944075-14123-3-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>

drm/i915: Use a crtc mask instead of a refcount for dpll functions, v2.

This makes it easier to verify correct dpll setup with only a single crtc.
It is also useful to detect double dpll enable/disable.

Changes since v1:
- Rebase on top of Ander's dpll rework.
- Change debugfs active to a mask.
- Change enabled_crtcs and active_crtcs to unsigned.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457944075-14123-2-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>

drm/i915: Fix race condition in intel_dp_destroy_mst_connector()

After unplugging a DP MST display from the system, we have to go through
and destroy all of the DRM connectors associated with it since none of
them are valid anymore. Unfortunately, intel_dp_destroy_mst_connector()
doesn't do a good enough job of ensuring that throughout the destruction
process that no modesettings can be done with the connectors. As it is
right now, intel_dp_destroy_mst_connector() works like this:

* Take all modeset locks
* Clear the configuration of the crtc on the connector, if there is one
* Drop all modeset locks, this is required because of circular
  dependency issues that arise with trying to remove the connector from
  sysfs with modeset locks held
* Unregister the connector
* Take all modeset locks, again
* Do the rest of the required cleaning for destroying the connector
* Finally drop all modeset locks for good

This only works sometimes. During the destruction process, it's very
possible that a userspace application will attempt to do a modesetting
using the connector. When we drop the modeset locks, an ioctl handler
such as drm_mode_setcrtc has the oppurtunity to take all of the modeset
locks from us. When this happens, one thing leads to another and
eventually we end up committing a mode with the non-existent connector:

[drm:intel_dp_link_training_clock_recovery [i915]] *ERROR* failed to enable link training
[drm:intel_dp_aux_ch] dp_aux_ch timeout status 0x7cf0001f
[drm:intel_dp_start_link_train [i915]] *ERROR* failed to start channel equalization
[drm:intel_dp_aux_ch] dp_aux_ch timeout status 0x7cf0001f
[drm:intel_mst_pre_enable_dp [i915]] *ERROR* failed to allocate vcpi

And in some cases, such as with the T460s using an MST dock, this
results in breaking modesetting and/or panicking the system.

To work around this, we now unregister the connector at the very
beginning of intel_dp_destroy_mst_connector(), grab all the modesetting
locks, and then hold them until we finish the rest of the function.

CC: stable@vger.kernel.org
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Rob Clark <rclark@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1458155884-13877-1-git-send-email-cpaul@redhat.com

drm/i915/guc: Support GuC SKL v6.1

This version of GuC firmware fixes the engine reset issue where golden
context LRC address is treated as page index by mistake. It also fixes
the problem that scheduler stops submiting to one engine when the other
engine work queue is full.

Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

drm/i915/bios: drop has_mipi in favor of intel_bios_is_dsi_present

Favor a single point of truth instead of duplicating the
information. The change also filters out unsupported DSI ports at this
stage, accepting only ports A and C, instead of waiting until the port
checks.

Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125015-7931-6-git-send-email-jani.nikula@intel.com

drm/i915/panel: setup pwm backlight based on connector type

Use the connector type instead of VBT directly to decide which backlight
mechanism to use on VLV/CHV. (Indirectly, this is the same thing, but
hides the VBT use.)

Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125015-7931-5-git-send-email-jani.nikula@intel.com

drm/i915: move VBT based DSI presence check to intel_bios.c

Hide knowledge about VBT child devices in intel_bios.c.

v2: Move port check to intel_bios.c (Sivakumar)

Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125015-7931-4-git-send-email-jani.nikula@intel.com

drm/i915: move VBT based eDP port check to intel_bios.c

Hide knowledge about VBT child devices in intel_bios.c.

Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125015-7931-3-git-send-email-jani.nikula@intel.com

drm/i915: move VBT based LVDS presence check to intel_bios.c

Hide knowledge about VBT child devices in intel_bios.c.

Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125015-7931-2-git-send-email-jani.nikula@intel.com

drm/i915: move VBT based TV presence check to intel_bios.c

Hide knowledge about VBT child devices in intel_bios.c.

v2: also move int_tv_support check to intel_bios.c (Sivakumar)

Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125015-7931-1-git-send-email-jani.nikula@intel.com

drm/i915/bxt: fix dsi hw state pipe readout

BXT isn't as limited as BYT and CHT regarding DSI pipes and ports.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/8bea85b86aaf7a15f854a656bf8d3208a3afe0bd.1458070700.git.jani.nikula@intel.com

drm/i915/dsi: refactor dsi get hw state readout

Make the code easier to read and update. No functional changes.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/04b20a9be6a9481ca2eb2a42cdcdc27358152e5f.1458070700.git.jani.nikula@intel.com

drm/i915: make transcoder_name return a string

Nicer for eDP (actually "EDP" instead of "D"), and makes future
expansion for DSI transcoders easier.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/2ac55ed584e450fe154daecb6453dff8eede5e7d.1458070700.git.jani.nikula@intel.com