GitHub/LineageOS/G12/android_kernel_amlogic_linux-4.9.git
11 years agoath9k: Remove incorrect diversity initialization
Sujith Manoharan [Mon, 16 Sep 2013 05:07:01 +0000 (10:37 +0530)]
ath9k: Remove incorrect diversity initialization

Fast antenna diversity is required only for single chain
chips and the diversity initialization is done in the
per-family board setup routines. Enabling of diversity
should be done based on the calibrated EEPROM/OTP data,
doing it for all chips is incorrect.

Remove the code that sets the fast_div bit for all cards, since
the documentation for the AR_PHY_CCK_DETECT register says:

reg 642: sig_detect_cck
enable_ant_fast_div : Only used for single chain chips.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoath9k: Handle FATAL interrupts correctly
Sujith Manoharan [Mon, 16 Sep 2013 05:07:00 +0000 (10:37 +0530)]
ath9k: Handle FATAL interrupts correctly

When a FATAL interrupt is received, a full chip reset is
required, which is done in the main tasklet. But since
the reset routine is scheduled as a work item, make sure
that interrupts are not enabled in the tasklet before the
reset is done.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoath9k: Fix NF calibration for single stream cards
Sujith Manoharan [Mon, 16 Sep 2013 05:06:59 +0000 (10:36 +0530)]
ath9k: Fix NF calibration for single stream cards

Rather than using the chip ID to read only chain-0 CCA
registers and avoid reading chain-1, use the RX chainmask
instead. There are some 1-stream PCI devices based on AR9287
such as TL-WN751ND. Improper NF calibration might result in
DMA errors/timeouts.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agortlwifi: rtl8192cu: Convert driver to use rtl_process_phyinfo()
Larry Finger [Fri, 13 Sep 2013 17:44:27 +0000 (12:44 -0500)]
rtlwifi: rtl8192cu: Convert driver to use rtl_process_phyinfo()

Remove routine _rtl92c_process_phyinfo() by using the equivalent routine
in driver rtlwifi.

This change also allows the removal of 5 additional routines from rtl8192cu.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoath9k: mark wmi_event_swba as __packed
Chris Metcalf [Fri, 13 Sep 2013 16:14:09 +0000 (12:14 -0400)]
ath9k: mark wmi_event_swba as __packed

The other structures in wmi.h are already marked this way.
Without this marking, we get an unaliged access panic in the tilegx kernel:

Starting stack dump of tid 0, pid 0 (swapper) on cpu 35 at cycle 198675113844
  frame 0: 0xfffffff7103ada90 ath9k_htc_swba+0x120/0x618 [ath9k_htc]
  frame 1: 0xfffffff7103a4b10 ath9k_wmi_event_tasklet+0x1b0/0x270 [ath9k_htc]
  frame 2: 0xfffffff700326570 tasklet_action+0x148/0x298
  [...]

Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agort2x00: rt2800lib: fix band selection and LNA PE control for RT3593 PCIe cards
Gabor Juhos [Wed, 11 Sep 2013 17:56:45 +0000 (19:56 +0200)]
rt2x00: rt2800lib: fix band selection and LNA PE control for RT3593 PCIe cards

The band selection and PE control code for the
RT3593 chipsets only handles USB based devices
currently. Due to this limitation RT3593 based
PCIe cards are not working correctly.

On PCIe cards band selection is controlled via
GPIO #8 which is identical to the USB devices.
The LNA PE control is slightly different, all
LNA PEs are controlled by GPIO #4.

Update the code to configure the GPIO_CTRL register
correctly on PCIe devices.

Cc: Steven Liu <steven.liu@mediatek.com>
Cc: JasonYS Cheng <jasonys.cheng@mediatek.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoath9k: Fix PeakDetect calibration for AR9462
Sujith Manoharan [Wed, 11 Sep 2013 11:06:32 +0000 (16:36 +0530)]
ath9k: Fix PeakDetect calibration for AR9462

Since HW PeakDetect calibration is turned on for AR9462,
various conditions have to be handled in the driver:

* Enable agc_cal when loading RTT fails.
* Disable SW PeakDetect calibration when RTT calibration is not enabled.
* Keep SW PeakDetect calibration result in driver.
* Update RTT table according to the saved value.
* Write RTT back after modifying SW RTT table.
* Enable local mode for PeakDetect calibration and restore values.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoath9k: Use bitops for calibration flags
Sujith Manoharan [Wed, 11 Sep 2013 11:06:31 +0000 (16:36 +0530)]
ath9k: Use bitops for calibration flags

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoath9k: Handle abnormal NAV in AP mode
Sujith Manoharan [Wed, 11 Sep 2013 16:00:27 +0000 (21:30 +0530)]
ath9k: Handle abnormal NAV in AP mode

Beacon transmission would get stuck if the NAV is
an invalid value for some reason. Check and correct
the NAV value in the HW when this happens.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoath9k: Fix issue with parsing malformed CFP IE
Sujith Manoharan [Wed, 11 Sep 2013 06:10:58 +0000 (11:40 +0530)]
ath9k: Fix issue with parsing malformed CFP IE

All QCA chips have the ability to parse the CF Parameter Set
IE in beacons. If the IE is malformed in the beacons from some
APs [1], the HW locks up. In AP mode, a beacon stuck would happen
and in client mode, a disconnection usually is the result.

To fix this issue, set the AR_PCU_MISC_MODE2_CFP_IGNORE to ignore
the CFP IE in beacons - this is applicable for all chips. For
AP mode, if this issue happens, the NAV is also corrupted and has
to be reset - this will be done in a subsequent patch.

[1] : http://msujith.org/ath9k/cfp/Malformed-CF-Param.png

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoath9k: Fix calibration for AR9462
Sujith Manoharan [Wed, 11 Sep 2013 06:10:57 +0000 (11:40 +0530)]
ath9k: Fix calibration for AR9462

TX IQ calibration is disabled by default for AR9462, this
is done using the initvals (reg 0xa644).

But, to compensate for this, the AR_PHY_RX_DELAY register
should be set to the max allowed value when performing
calibration.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agowireless: rtl818x: remove unnecessary pci_set_drvdata()
Jingoo Han [Tue, 10 Sep 2013 11:32:19 +0000 (20:32 +0900)]
wireless: rtl818x: remove unnecessary pci_set_drvdata()

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agowireless: p54pci: remove unnecessary pci_set_drvdata()
Jingoo Han [Tue, 10 Sep 2013 11:30:49 +0000 (20:30 +0900)]
wireless: p54pci: remove unnecessary pci_set_drvdata()

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agowireless: orinoco: remove unnecessary pci_set_drvdata()
Jingoo Han [Tue, 10 Sep 2013 11:29:19 +0000 (20:29 +0900)]
wireless: orinoco: remove unnecessary pci_set_drvdata()

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agowireless: mwl8k: remove unnecessary pci_set_drvdata()
Jingoo Han [Tue, 10 Sep 2013 11:27:49 +0000 (20:27 +0900)]
wireless: mwl8k: remove unnecessary pci_set_drvdata()

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agowireless: ipw2x00: remove unnecessary pci_set_drvdata()
Jingoo Han [Tue, 10 Sep 2013 11:27:09 +0000 (20:27 +0900)]
wireless: ipw2x00: remove unnecessary pci_set_drvdata()

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agowireless: wil6210: remove unnecessary pci_set_drvdata()
Jingoo Han [Tue, 10 Sep 2013 11:26:13 +0000 (20:26 +0900)]
wireless: wil6210: remove unnecessary pci_set_drvdata()

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agowireless: ath10k: remove unnecessary pci_set_drvdata()
Jingoo Han [Tue, 10 Sep 2013 11:25:11 +0000 (20:25 +0900)]
wireless: ath10k: remove unnecessary pci_set_drvdata()

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agowireless: airo: remove unnecessary pci_set_drvdata()
Jingoo Han [Tue, 10 Sep 2013 11:23:50 +0000 (20:23 +0900)]
wireless: airo: remove unnecessary pci_set_drvdata()

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agowireless: adm8211: remove unnecessary pci_set_drvdata()
Jingoo Han [Tue, 10 Sep 2013 11:22:10 +0000 (20:22 +0900)]
wireless: adm8211: remove unnecessary pci_set_drvdata()

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agowireless: iwlegacy: remove unnecessary pci_set_drvdata()
Jingoo Han [Tue, 10 Sep 2013 11:19:41 +0000 (20:19 +0900)]
wireless: iwlegacy: remove unnecessary pci_set_drvdata()

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agowireless: rtlwifi: remove unnecessary pci_set_drvdata()
Jingoo Han [Tue, 10 Sep 2013 11:18:38 +0000 (20:18 +0900)]
wireless: rtlwifi: remove unnecessary pci_set_drvdata()

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agowireless: wl12xx: use dev_get_platdata()
Jingoo Han [Tue, 10 Sep 2013 08:58:32 +0000 (17:58 +0900)]
wireless: wl12xx: use dev_get_platdata()

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agowireless: wlcore: use dev_get_platdata()
Jingoo Han [Tue, 10 Sep 2013 08:57:57 +0000 (17:57 +0900)]
wireless: wlcore: use dev_get_platdata()

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agowireless: wl1251: use dev_get_platdata()
Jingoo Han [Tue, 10 Sep 2013 08:57:05 +0000 (17:57 +0900)]
wireless: wl1251: use dev_get_platdata()

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agowireless: libertas: use dev_get_platdata()
Jingoo Han [Tue, 10 Sep 2013 08:56:27 +0000 (17:56 +0900)]
wireless: libertas: use dev_get_platdata()

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agowireless: cw1200: use dev_get_platdata()
Jingoo Han [Tue, 10 Sep 2013 08:55:41 +0000 (17:55 +0900)]
wireless: cw1200: use dev_get_platdata()

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agowireless: brcmfmac: use dev_get_platdata()
Jingoo Han [Tue, 10 Sep 2013 08:54:47 +0000 (17:54 +0900)]
wireless: brcmfmac: use dev_get_platdata()

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agowireless: ath9k: use dev_get_platdata()
Jingoo Han [Tue, 10 Sep 2013 08:53:02 +0000 (17:53 +0900)]
wireless: ath9k: use dev_get_platdata()

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agowireless: ath5k: use dev_get_platdata()
Jingoo Han [Tue, 10 Sep 2013 08:51:47 +0000 (17:51 +0900)]
wireless: ath5k: use dev_get_platdata()

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agonet: ath9k: Use NULL instead of false
Sachin Kamat [Tue, 10 Sep 2013 06:20:36 +0000 (11:50 +0530)]
net: ath9k: Use NULL instead of false

The function returns a pointer. Hence return NULL instead of false.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoar5523: Add USB ID of D-Link WUA-2340 rev A1
Albert Pool [Mon, 9 Sep 2013 18:36:30 +0000 (20:36 +0200)]
ar5523: Add USB ID of D-Link WUA-2340 rev A1

Signed-off-by: Albert Pool <albertpool@solcon.nl>
Reported-by: Michael Landrum <landrummd@gmail.com>
Acked-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agort2800: comment enable radio initialization sequence
Stanislaw Gruszka [Mon, 9 Sep 2013 10:37:38 +0000 (12:37 +0200)]
rt2800: comment enable radio initialization sequence

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agomwifiex: Remove casting the return value which is a void pointer
Jingoo Han [Mon, 9 Sep 2013 05:26:51 +0000 (14:26 +0900)]
mwifiex: Remove casting the return value which is a void pointer

Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoath9k: replace snprintf() with scnprintf()
Zefir Kurtisi [Thu, 5 Sep 2013 12:11:57 +0000 (14:11 +0200)]
ath9k: replace snprintf() with scnprintf()

Whenever the return value of snprintf() is used to calculate
remaining buffer-space, we wanted to use sncprintf() instead.

Indentation is adapted where possible. Some lines exceed the
line width limit, either they did it already before, or
since they can not be broken reasonably well.

Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoath9k: Add DELL 1707 to supported card table
Sujith Manoharan [Thu, 5 Sep 2013 05:26:54 +0000 (10:56 +0530)]
ath9k: Add DELL 1707 to supported card table

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoath9k: Update AR9485 1.1 initvals
Sujith Manoharan [Tue, 3 Sep 2013 04:58:57 +0000 (10:28 +0530)]
ath9k: Update AR9485 1.1 initvals

* Remove duplicate array mappings.
* Fix ETSI CCA compliance.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoath9k: Add and use initvals for channel 14
Sujith Manoharan [Tue, 3 Sep 2013 04:58:56 +0000 (10:28 +0530)]
ath9k: Add and use initvals for channel 14

This is missing for AR9565.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoath9k: Fix regulatory compliance for AR9462/AR9565
Sujith Manoharan [Tue, 3 Sep 2013 04:58:55 +0000 (10:28 +0530)]
ath9k: Fix regulatory compliance for AR9462/AR9565

Adjust the CCA values based on the regulatory domain
present in the EEPROM.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoath9k: Identify WB335 Antenna configuration
Sujith Manoharan [Mon, 2 Sep 2013 08:29:06 +0000 (13:59 +0530)]
ath9k: Identify WB335 Antenna configuration

There are 2 types of WB335 cards, 1-antenna and 2-antenna.
Identify them based on PCI subsystem IDs, this will be used
for MCI/BTCOEX tweaks.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoath9k: Identify CUS252 cards
Sujith Manoharan [Mon, 2 Sep 2013 08:29:05 +0000 (13:59 +0530)]
ath9k: Identify CUS252 cards

These cards are based on WB335/AR9565.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoath9k: Enable antenna diversity for WB335
Sujith Manoharan [Mon, 2 Sep 2013 08:29:04 +0000 (13:59 +0530)]
ath9k: Enable antenna diversity for WB335

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoath9k: Add support for AR9565 v1.0.1 LNA diversity
Sujith Manoharan [Mon, 2 Sep 2013 08:29:03 +0000 (13:59 +0530)]
ath9k: Add support for AR9565 v1.0.1 LNA diversity

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoath9k: Use correct RX gain table for AR9565
Sujith Manoharan [Mon, 2 Sep 2013 08:29:02 +0000 (13:59 +0530)]
ath9k: Use correct RX gain table for AR9565

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoath9k: Fix antenna diversity init for AR9565
Sujith Manoharan [Mon, 2 Sep 2013 08:29:01 +0000 (13:59 +0530)]
ath9k: Fix antenna diversity init for AR9565

Program the HW registers (AR_PHY_CCK_DETECT, AR_PHY_MC_GAIN_CTRL)
with the correct values for AR9565 to allow LNA combining.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoath9k: Bypass EEPROM for diversity cap for AR9565
Sujith Manoharan [Mon, 2 Sep 2013 08:29:00 +0000 (13:59 +0530)]
ath9k: Bypass EEPROM for diversity cap for AR9565

Use a default antenna diversity value for AR9565 instead
of relying on the EEPROM/OTP programmed value.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoath9k: Update initvals for AR9565 1.0
Sujith Manoharan [Mon, 2 Sep 2013 08:28:59 +0000 (13:58 +0530)]
ath9k: Update initvals for AR9565 1.0

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoMerge branch 'for-linville' of git://github.com/kvalo/ath
John W. Linville [Thu, 26 Sep 2013 18:54:17 +0000 (14:54 -0400)]
Merge branch 'for-linville' of git://github.com/kvalo/ath

11 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Linus Torvalds [Thu, 19 Sep 2013 18:57:28 +0000 (13:57 -0500)]
Merge git://git./linux/kernel/git/davem/net

Pull networking fixes from David Miller:

 1) If the local_df boolean is set on an SKB we have to allocate a
    unique ID even if IP_DF is set in the ipv4 headers, from Ansis
    Atteka.

 2) Some fixups for the new chipset support that went into the sfc
    driver, from Ben Hutchings.

 3) Because SCTP bypasses a good chunk of, and actually duplicates, the
    logic of the ipv6 output path, some IPSEC things don't get done
    properly.  Integrate SCTP better into the ipv6 output path so that
    these problems are fixed and such issues don't get missed in the
    future either.  From Daniel Borkmann.

 4) Fix skge regressions added by the DMA mapping error return checking
    added in v3.10, from Mikulas Patocka.

 5) Kill some more IRQF_DISABLED references, from Michael Opdenacker.

 6) Fix races and deadlocks in the bridging code, from Hong Zhiguo.

 7) Fix error handling in tun_set_iff(), in particular don't leak
    resources.  From Jason Wang.

 8) Prevent format-string injection into xen-netback driver, from Kees
    Cook.

 9) Fix regression added to netpoll ARP packet handling, in particular
    check for the right ETH_P_ARP protocol code.  From Sonic Zhang.

10) Try to deal with AMD IOMMU errors when using r8169 chips, from
    Francois Romieu.

11) Cure freezes due to recent changes in the rt2x00 wireless driver,
    from Stanislaw Gruszka.

12) Don't do SPI transfers (which can sleep) in interrupt context in
    cw1200 driver, from Solomon Peachy.

13) Fix LEDs handling bug in 5720 tg3 chips already handled for 5719.
    From Nithin Sujir.

14) Make xen_netbk_count_skb_slots() count the actual number of slots
    that will be used, taking into consideration packing and other
    issues that the transmit path will run into.  From David Vrabel.

15) Use the correct maximum age when calculating the bridge
    message_age_timer, from Chris Healy.

16) Get rid of memory leaks in mcs7780 IRDA driver, from Alexey
    Khoroshilov.

17) Netfilter conntrack extensions were converted to RCU but are not
    always freed properly using kfree_rcu().  Fix from Michal Kubecek.

18) VF reset recovery not being done correctly in qlcnic driver, from
    Manish Chopra.

19) Fix inverted test in ATM nicstar driver, from Andy Shevchenko.

20) Missing workqueue destroy in cxgb4 error handling, from Wei Yang.

21) Internal switch not initialized properly in bgmac driver, from RafaÅ‚
    MiÅ‚ecki.

22) Netlink messages report wrong local and remote addresses in IPv6
    tunneling, from Ding Zhi.

23) ICMP redirects should not generate socket errors in DCCP and SCTP.
    We're still working out how this should be handled for RAW and UDP
    sockets.  From Daniel Borkmann and Duan Jiong.

24) We've had several bugs wherein the network namespace's loopback
    device gets accessed after it is free'd, NULL it out so that we can
    catch these problems more readily.  From Eric W Biederman.

25) Fix regression in TCP RTO calculations, from Neal Cardwell.

26) Fix too early free of xen-netback network device when VIFs still
    exist.  From Paul Durrant.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
  netconsole: fix a deadlock with rtnl and netconsole's mutex
  netpoll: fix NULL pointer dereference in netpoll_cleanup
  skge: fix broken driver
  ip: generate unique IP identificator if local fragmentation is allowed
  ip: use ip_hdr() in __ip_make_skb() to retrieve IP header
  xen-netback: Don't destroy the netdev until the vif is shut down
  net:dccp: do not report ICMP redirects to user space
  cnic: Fix crash in cnic_bnx2x_service_kcq()
  bnx2x, cnic, bnx2i, bnx2fc: Fix bnx2i and bnx2fc regressions.
  vxlan: Avoid creating fdb entry with NULL destination
  tcp: fix RTO calculated from cached RTT
  drivers: net: phy: cicada.c: clears warning Use #include <linux/io.h> instead of <asm/io.h>
  net loopback: Set loopback_dev to NULL when freed
  batman-adv: set the TAG flag for the vid passed to BLA
  netfilter: nfnetlink_queue: use network skb for sequence adjustment
  net: sctp: rfc4443: do not report ICMP redirects to user space
  net: usb: cdc_ether: use usb.h macros whenever possible
  net: usb: cdc_ether: fix checkpatch errors and warnings
  net: usb: cdc_ether: Use wwan interface for Telit modules
  ip6_tunnels: raddr and laddr are inverted in nl msg
  ...

11 years agonetconsole: fix a deadlock with rtnl and netconsole's mutex
Nikolay Aleksandrov [Thu, 19 Sep 2013 13:02:36 +0000 (15:02 +0200)]
netconsole: fix a deadlock with rtnl and netconsole's mutex

This bug was introduced by commit
7a163bfb7ce50895bbe67300ea610d31b9c09230 ("netconsole: avoid a crash with
multiple sysfs writers"). In store_enabled() we have the following
sequence: acquire nt->mutex then rtnl, but in the netconsole netdev
notifier we have rtnl then nt->mutex effectively leading to a deadlock.
The NULL pointer dereference that the above commit tries to fix is
actually due to another bug in netpoll_cleanup(). This is fixed by dropping
the mutex from the netdev notifier as it's already protected by rtnl.

Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonetpoll: fix NULL pointer dereference in netpoll_cleanup
Nikolay Aleksandrov [Thu, 19 Sep 2013 13:02:35 +0000 (15:02 +0200)]
netpoll: fix NULL pointer dereference in netpoll_cleanup

I've been hitting a NULL ptr deref while using netconsole because the
np->dev check and the pointer manipulation in netpoll_cleanup are done
without rtnl and the following sequence happens when having a netconsole
over a vlan and we remove the vlan while disabling the netconsole:
CPU 1 CPU2
removes vlan and calls the notifier
enters store_enabled(), calls
netdev_cleanup which checks np->dev
and then waits for rtnl
executes the netconsole netdev
release notifier making np->dev
== NULL and releases rtnl
continues to dereference a member of
np->dev which at this point is == NULL

Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoskge: fix broken driver
Mikulas Patocka [Thu, 19 Sep 2013 18:13:17 +0000 (14:13 -0400)]
skge: fix broken driver

The patch 136d8f377e1575463b47840bc5f1b22d94bf8f63 broke the skge driver.
Note this part of the patch:
+               if (skge_rx_setup(skge, e, nskb, skge->rx_buf_size) < 0) {
+                       dev_kfree_skb(nskb);
+                       goto resubmit;
+               }
+
                pci_unmap_single(skge->hw->pdev,
                                 dma_unmap_addr(e, mapaddr),
                                 dma_unmap_len(e, maplen),
                                 PCI_DMA_FROMDEVICE);
                skb = e->skb;
                prefetch(skb->data);
-               skge_rx_setup(skge, e, nskb, skge->rx_buf_size);

The function skge_rx_setup modifies e->skb to point to the new skb. Thus,
after this change, the new buffer, not the old, is returned to the
networking stack.

This bug is present in kernels 3.11, 3.11.1 and 3.12-rc1. The patch should
be queued for 3.11-stable.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Vasiliy Glazov <vascom2@gmail.com>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoip: generate unique IP identificator if local fragmentation is allowed
Ansis Atteka [Wed, 18 Sep 2013 22:29:53 +0000 (15:29 -0700)]
ip: generate unique IP identificator if local fragmentation is allowed

If local fragmentation is allowed, then ip_select_ident() and
ip_select_ident_more() need to generate unique IDs to ensure
correct defragmentation on the peer.

For example, if IPsec (tunnel mode) has to encrypt large skbs
that have local_df bit set, then all IP fragments that belonged
to different ESP datagrams would have used the same identificator.
If one of these IP fragments would get lost or reordered, then
peer could possibly stitch together wrong IP fragments that did
not belong to the same datagram. This would lead to a packet loss
or data corruption.

Signed-off-by: Ansis Atteka <aatteka@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoip: use ip_hdr() in __ip_make_skb() to retrieve IP header
Ansis Atteka [Wed, 18 Sep 2013 22:29:52 +0000 (15:29 -0700)]
ip: use ip_hdr() in __ip_make_skb() to retrieve IP header

skb->data already points to IP header, but for the sake of
consistency we can also use ip_hdr() to retrieve it.

Signed-off-by: Ansis Atteka <aatteka@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoxen-netback: Don't destroy the netdev until the vif is shut down
Paul Durrant [Tue, 17 Sep 2013 16:46:08 +0000 (17:46 +0100)]
xen-netback: Don't destroy the netdev until the vif is shut down

Without this patch, if a frontend cycles through states Closing
and Closed (which Windows frontends need to do) then the netdev
will be destroyed and requires re-invocation of hotplug scripts
to restore state before the frontend can move to Connected. Thus
when udev is not in use the backend gets stuck in InitWait.

With this patch, the netdev is left alone whilst the backend is
still online and is only de-registered and freed just prior to
destroying the vif (which is also nicely symmetrical with the
netdev allocation and registration being done during probe) so
no re-invocation of hotplug scripts is required.

Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Linus Torvalds [Thu, 19 Sep 2013 17:52:25 +0000 (12:52 -0500)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus

Pull MIPS updates from Ralf Baechle:
 - Minor updates and fixes to the Octeon ethernet driver in staging
 - A fix to VGA_MAP_MEM() for 64 bit platforms
 - Fix a workaround for 74K/1074K processors
 - The symlink arch/mips/boot/dts/include/dt-bindings was pointing to a
   a file with a name ending in \n.  I think this may have been caused
   by a git bug with with patches sent by email
 - A build fix for VGA console on BCM1480-based systems
 - Fix PCI device access via "/sys/bus/pci/.../resource0" or similar
   work for Alchemy platforms
 - Fix potential data leak on MIPS R5 cores.  This doesn't add proper
   support for any R5 features, just ensures a kernel without such
   support will be secure to run
 - Adding a macros for the CP0 Config5 register to be used by the R5 fix
 - Make get_cycles() actually return something useful where possible
   This also requires a preparatory patch for performance sake
 - Fix a warning about the use of smp_processor_id() in preemptible
   code.  Again this includes a preparatory patch adding the
   infrastructure to be used by the actual patch
 - Finally remove pointless one-line comment

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Fix invalid symbolic link file
  MIPS: PCI: pci-bcm1480: Include missing vt.h header
  MIPS: Disable usermode switching of the FR bit for MIPS R5 CPUs.
  MIPS: Add MIPS R5 config5 register.
  MIPS: PCI: Use pci_resource_to_user to map pci memory space properly
  MIPS: 74K/1074K: Correct erratum workaround.
  MIPS: Cleanup CP0 PRId and CP1 FPIR register access masks
  MIPS: Remove useless comment about kprobe from arch/mips/Makefile
  MIPS: Fix VGA_MAP_MEM macro.
  MIPS: Reimplement get_cycles().
  MIPS: Optimize current_cpu_type() for better code.
  MIPS: Fix accessing to per-cpu data when flushing the cache
  MIPS: Provide nice way to access boot CPU's data.
  staging: octeon-ethernet: rgmii: enable interrupts that we can handle
  staging: octeon-ethernet: remove skb alloc failure warnings
  staging: octeon-ethernet: make dropped packets to consume NAPI budget

11 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph...
Linus Torvalds [Thu, 19 Sep 2013 17:50:37 +0000 (12:50 -0500)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sage/ceph-client

Pull ceph fixes from Sage Weil:
 "These fix several bugs with RBD from 3.11 that didn't get tested in
  time for the merge window: some error handling, a use-after-free, and
  a sequencing issue when unmapping and image races with a notify
  operation.

  There is also a patch fixing a problem with the new ceph + fscache
  code that just went in"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  fscache: check consistency does not decrement refcount
  rbd: fix error handling from rbd_snap_name()
  rbd: ignore unmapped snapshots that no longer exist
  rbd: fix use-after free of rbd_dev->disk
  rbd: make rbd_obj_notify_ack() synchronous
  rbd: complete notifies before cleaning up osd_client and rbd_dev
  libceph: add function to ensure notifies are complete

11 years agoMIPS: Fix invalid symbolic link file
Madhavan Srinivasan [Thu, 19 Sep 2013 13:09:08 +0000 (18:39 +0530)]
MIPS: Fix invalid symbolic link file

Commit 3b29aa5ba204c [MIPS: add <dt-bindings/> symlink] created a symlink
file in include/dt-bindings.  Even though commit diff is fine, the symlink
is invalid and ls -lb shows a newline character at the end of the filename:

lrwxrwxrwx 1 maddy maddy 35 Sep 19 18:11 dt-bindings ->
../../../../../include/dt-bindings\n

Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Cc: steven.hill@imgtec.com
Cc: mmarek@suse.cz
Cc: swarren@nvidia.com
Cc: linux-mips@linux-mips.org
Cc: linux-kbuild@vger.kernel.org
Cc: james.hogan@imgtec.com
Patchwork: https://patchwork.linux-mips.org/patch/5859/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
11 years agoMIPS: PCI: pci-bcm1480: Include missing vt.h header
Markos Chandras [Thu, 19 Sep 2013 09:27:52 +0000 (10:27 +0100)]
MIPS: PCI: pci-bcm1480: Include missing vt.h header

It's needed for the MAX_NR_CONSOLES macro.

Fixes the following build problem on a randconfig:

arch/mips/pci/pci-bcm1480.c: In function 'bcm1480_pcibios_init':
arch/mips/pci/pci-bcm1480.c:261:36: error: 'MAX_NR_CONSOLES'
undeclared (first use in this function)
arch/mips/pci/pci-bcm1480.c:261:36: note: each undeclared
identifier is reported only once for each function it appears in
make[1]: *** [arch/mips/pci/pci-bcm1480.o] Error 1

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5858/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
11 years agoMIPS: Disable usermode switching of the FR bit for MIPS R5 CPUs.
Ralf Baechle [Thu, 19 Sep 2013 09:15:49 +0000 (11:15 +0200)]
MIPS: Disable usermode switching of the FR bit for MIPS R5 CPUs.

Currently the kernel will always use the FR=0 register model for O32.  If
an O32 application did enable FR=1 mode, some data from another application
might be leaked in the extra registers becoming visible.

Iow, this patch is meant to make the kernel MIPS R5 tolerant but leaves
proper MIPS R5 support to a future patchset.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
11 years agoMIPS: Add MIPS R5 config5 register.
Ralf Baechle [Thu, 19 Sep 2013 09:09:48 +0000 (11:09 +0200)]
MIPS: Add MIPS R5 config5 register.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
11 years agoMerge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Linus Torvalds [Thu, 19 Sep 2013 02:17:44 +0000 (21:17 -0500)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux

Pull drm radeon/nouveau/core fixes from Dave Airlie:
 "Mostly radeon fixes, with some nouveau bios parser, ttm fix and a fix
  for AST driver"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (42 commits)
  drm/fb-helper: don't sleep for screen unblank when an oops is in progress
  drm, ttm Fix uninitialized warning
  drm/ttm: fix the tt_populated check in ttm_tt_destroy()
  drm/nouveau/ttm: prevent double-free in nouveau_sgdma_create_ttm() failure path
  drm/nouveau/bios/init: fix thinko in INIT_CONFIGURE_MEM
  drm/nouveau/kms: enable for non-vga pci classes
  drm/nouveau/bios/init: stub opcode 0xaa
  drm/radeon: avoid UVD corruptions on AGP cards
  drm/radeon: fix panel scaling with eDP and LVDS bridges
  drm/radeon/dpm: rework auto performance level enable
  drm/radeon: Fix hmdi typo
  drm/radeon/dpm/rs780: fix force_performance state for same sclks
  drm/radeon/dpm/rs780: don't enable sclk scaling if not required
  drm/radeon/dpm/rs780: add some sanity checking to sclk scaling
  drm/radeon/dpm/rs780: use drm_mode_vrefresh()
  drm/udl: rip out set_need_resched
  drm/ast: fix the ast open key function
  drm/radeon/dpm: add bapm callback for kb/kv
  drm/radeon/dpm: add bapm callback for trinity
  drm/radeon/dpm: add infrastructure to properly handle bapm
  ...

11 years agodrm/fb-helper: don't sleep for screen unblank when an oops is in progress
Daniel Vetter [Fri, 13 Sep 2013 21:49:57 +0000 (14:49 -0700)]
drm/fb-helper: don't sleep for screen unblank when an oops is in progress

Otherwise the system will burn even brighter and worse, leave the user
wondering what's going on exactly.

Since we already have a panic handler which will (try) to restore the
entire fbdev console mode, we can just bail out.  Inspired by a patch from
Konstantin Khlebnikov.  The callchain leading to this, cut&pasted from
Konstantin's original patch:

callstack:
panic()
bust_spinlocks(1)
unblank_screen()
vc->vc_sw->con_blank()
fbcon_blank()
fb_blank()
info->fbops->fb_blank()
drm_fb_helper_blank()
drm_fb_helper_dpms()
drm_modeset_lock_all()
mutex_lock(&dev->mode_config.mutex)

Note that the entire locking in the fb helper around panic/sysrq and kdbg
is ...  non-existant.  So we have a decent change of blowing up
everything.  But since reworking this ties in with funny concepts like the
fbdev notifier chain or the impressive things which happen around
console_lock while oopsing, I'll leave that as an exercise for braver
souls than me.

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Dave Airlie <airlied@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
11 years agodrm, ttm Fix uninitialized warning
Prarit Bhargava [Fri, 13 Sep 2013 12:33:34 +0000 (08:33 -0400)]
drm, ttm Fix uninitialized warning

Fix uninitialized warning.

drivers/gpu/drm/ttm/ttm_object.c: In function â€˜ttm_base_object_lookup’:
drivers/gpu/drm/ttm/ttm_object.c:213:10: error: â€˜base’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
  kref_put(&base->refcount, ttm_release_base);
          ^
drivers/gpu/drm/ttm/ttm_object.c:221:26: note: â€˜base’ was declared here
  struct ttm_base_object *base;

Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
11 years agodrm/ttm: fix the tt_populated check in ttm_tt_destroy()
Ben Skeggs [Tue, 17 Sep 2013 04:21:15 +0000 (14:21 +1000)]
drm/ttm: fix the tt_populated check in ttm_tt_destroy()

After a vmalloc failure in ttm_dma_tt_alloc_page_directory(),
ttm_dma_tt_init() will call ttm_tt_destroy() to cleanup, and end up
inside the driver's unpopulate() hook when populate() has never yet
been called.

On nouveau, the first issue to be hit because of this is that
dma_address[] may be a NULL pointer.  After working around this,
ttm_pool_unpopulate() may potentially hit the same issue with
the pages[] array.

It seems to make more sense to avoid calling unpopulate on already
unpopulated TTMs than to add checks to all the implementations.

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Cc: stable@vger.kernel.org
Cc: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
11 years agoMerge branch 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux...
Dave Airlie [Thu, 19 Sep 2013 01:47:23 +0000 (11:47 +1000)]
Merge branch 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes

A couple of bios parser fixes (one for ancient chips, another for new ones - important in Optimus configs).  Another to make sure KMS is enabled on certain Optimus configs, and a TTM failure path fix.

* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
  drm/nouveau/ttm: prevent double-free in nouveau_sgdma_create_ttm() failure path
  drm/nouveau/bios/init: fix thinko in INIT_CONFIGURE_MEM
  drm/nouveau/kms: enable for non-vga pci classes
  drm/nouveau/bios/init: stub opcode 0xaa

11 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Linus Torvalds [Thu, 19 Sep 2013 00:22:22 +0000 (19:22 -0500)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs

Pull vfs fixes from Al Viro:
 "atomic_open-related fixes (Miklos' series, with EEXIST-related parts
  replaced with fix in fs/namei.c:atomic_open() instead of messing with
  the instances) + race fix in autofs + leak on failure exit in 9p"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  9p: don't forget to destroy inode cache if fscache registration fails
  atomic_open: take care of EEXIST in no-open case with O_CREAT|O_EXCL in fs/namei.c
  vfs: don't set FILE_CREATED before calling ->atomic_open()
  nfs: set FILE_CREATED
  gfs2: set FILE_CREATED
  cifs: fix filp leak in cifs_atomic_open()
  vfs: improve i_op->atomic_open() documentation
  autofs4: close the races around autofs4_notify_daemon()

11 years agoMIPS: PCI: Use pci_resource_to_user to map pci memory space properly
Wolfgang Grandegger [Mon, 13 Dec 2010 20:48:10 +0000 (21:48 +0100)]
MIPS: PCI: Use pci_resource_to_user to map pci memory space properly

[ralf@linux-mips.org: This only matters to Alchemy platforms.  On other
platforms fixup_bigphys_addr is just an identidy mapping.]

Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Cc: tiejun.chen <tiejun.chen@windriver.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1868/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
11 years agoMIPS: 74K/1074K: Correct erratum workaround.
Maciej W. Rozycki [Wed, 18 Sep 2013 18:08:15 +0000 (19:08 +0100)]
MIPS: 74K/1074K: Correct erratum workaround.

Make sure 74K revision numbers are not applied to the 1074K.  Also catch
invalid usage.

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5857/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
11 years agoMIPS: Cleanup CP0 PRId and CP1 FPIR register access masks
Maciej W. Rozycki [Tue, 17 Sep 2013 15:58:10 +0000 (16:58 +0100)]
MIPS: Cleanup CP0 PRId and CP1 FPIR register access masks

Replace hardcoded CP0 PRId and CP1 FPIR register access masks throughout.
The change does not touch places that use shifted or partial masks.

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5838/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
11 years agoMerge tag 'please-pull-pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl...
Linus Torvalds [Wed, 18 Sep 2013 17:39:40 +0000 (12:39 -0500)]
Merge tag 'please-pull-pstore' of git://git./linux/kernel/git/aegl/linux

Pull pstore/compression fixes from Tony Luck:
 "Three pstore fixes related to compression:
   1) Better adjustment of size of compression buffer (was too big for
      EFIVARS backend resulting in compression failure
   2) Use zlib_inflateInit2 instead of zlib_inflateInit
   3) Don't print messages about compression failure.  They will waste
      space that may better be used to log console output leading to the
      crash"

* tag 'please-pull-pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
  pstore: Remove the messages related to compression failure
  pstore: Use zlib_inflateInit2 instead of zlib_inflateInit
  pstore: Adjust buffer size for compression for smaller registered buffers

11 years agoMIPS: Remove useless comment about kprobe from arch/mips/Makefile
Wu Zhangjin [Tue, 9 Nov 2010 16:25:53 +0000 (00:25 +0800)]
MIPS: Remove useless comment about kprobe from arch/mips/Makefile

The commit c1bf207d6ee1eb72e9c10365edbdc7c9ff7fb9b0 (kernel.org) rsp.
58e9ad32a48dce37ffeea912f55bd1c94b85ad7f (lmo) [MIPS: kprobe: Add support]
introduced a useless comment.

Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: David Daney <ddaney@caviumnetworks.com>
Patchwork: https://patchwork.linux-mips.org/patch/1765/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
11 years agonet:dccp: do not report ICMP redirects to user space
Duan Jiong [Wed, 18 Sep 2013 12:03:27 +0000 (20:03 +0800)]
net:dccp: do not report ICMP redirects to user space

DCCP shouldn't be setting sk_err on redirects as it
isn't an error condition. it should be doing exactly
what tcp is doing and leaving the error handler without
touching the socket.

Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Wed, 18 Sep 2013 16:26:17 +0000 (11:26 -0500)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull x86 fixes from Ingo Molnar:
 "Misc fixes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/intel/lpss: Add pin control support to Intel low power subsystem
  perf/x86/intel: Mark MEM_LOAD_UOPS_MISS_RETIRED as precise on SNB
  x86: Remove now-unused save_rest()
  x86/smpboot: Fix announce_cpu() to printk() the last "OK" properly

11 years agoMerge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Wed, 18 Sep 2013 16:24:49 +0000 (11:24 -0500)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull timer fix from Ingo Molnar:
 "An NTP related lockup fix"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Fix HRTICK related deadlock from ntp lock changes

11 years agocnic: Fix crash in cnic_bnx2x_service_kcq()
Michael Chan [Wed, 18 Sep 2013 08:50:39 +0000 (01:50 -0700)]
cnic: Fix crash in cnic_bnx2x_service_kcq()

commit 104a43edb264321a4d41850e98153b4fa8a9ef42
    cnic: Use CHIP_NUM macros from bnx2x.h

changed the code to use the bnx2x macro NO_FCOE() to determine if FCoE
is supported or not.  There is another place in cnic that is still using
the old method to determine if FCoE is supported or not.  The 2 methods
may not yield the same result after the network interface is brought down
and up.  This will cause the crash as cnic_bnx2x_service_kcq() will access
the uninitialized cp->kcq2.

The fix is to consistently use the same macro CNIC_SUPPORTS_FCOE() which
uses the bnx2x NO_FCOE() macro.  As a follow-up, we can clean up the code
to remove the old method as it is no longer needed.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agobnx2x, cnic, bnx2i, bnx2fc: Fix bnx2i and bnx2fc regressions.
Michael Chan [Wed, 18 Sep 2013 08:50:38 +0000 (01:50 -0700)]
bnx2x, cnic, bnx2i, bnx2fc: Fix bnx2i and bnx2fc regressions.

commit b9871bcfd211d316adee317608dab44c58d6ea2d
    bnx2x: VF RSS support - PF side

changed the configuration of the doorbell HW and it broke iSCSI and FCoE.
We fix this by making compatible changes to the doorbell address in bnx2i
and bnx2fc.  For the userspace driver, we need to pass a modified CID
so that the existing userspace driver will calculate the correct doorbell
address and continue to work.

Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Wed, 18 Sep 2013 16:23:32 +0000 (11:23 -0500)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull scheduler fixes from Ingo Molnar:
 "Misc fixes"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Fix comment for sched_info_depart
  sched/Documentation: Update sched-design-CFS.txt documentation
  sched/debug: Take PID namespace into account
  sched/fair: Fix small race where child->se.parent,cfs_rq might point to invalid ones

11 years agoMerge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Wed, 18 Sep 2013 16:22:53 +0000 (11:22 -0500)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull perf fixes from Ingo Molnar:
 "Two small fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Fix UAPI export of PERF_EVENT_IOC_ID
  perf/x86/intel: Fix Silvermont offcore masks

11 years agoMerge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
David S. Miller [Wed, 18 Sep 2013 16:22:17 +0000 (12:22 -0400)]
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge

Included change:
- fix the Bridge Loop Avoidance component by marking the variables containing
  the VLAN ID with the HAS_TAG flag when needed.

11 years agoMIPS: Fix VGA_MAP_MEM macro.
Leonid Yegoshin [Wed, 11 Sep 2013 00:36:04 +0000 (19:36 -0500)]
MIPS: Fix VGA_MAP_MEM macro.

Use the CKSEG1ADDR macro when calculating VGA_MAP_MEM.

[ralf@linux-mips.org: Include <asm/addrspace.h for CKSEG1ADDR.]

Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5814/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
11 years agoMIPS: Reimplement get_cycles().
Ralf Baechle [Thu, 12 Sep 2013 11:47:32 +0000 (13:47 +0200)]
MIPS: Reimplement get_cycles().

This essentially reverts commit efb9ca08b5a2374b29938cdcab417ce4feb14b54
(kernel.org) / 58020a106879a8b372068741c81f0015c9b0b96dbv [[MIPS] Change
get_cycles to always return 0.]

Most users of get_cycles() invoke it as a timing interface.  That's why
in modern kernels it was never very much missed for.  /dev/random however
uses get_cycles() in the how the jitter in the interrupt timing contains
some useful entropy.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
11 years agoperf: Fix UAPI export of PERF_EVENT_IOC_ID
Vince Weaver [Tue, 17 Sep 2013 18:53:41 +0000 (14:53 -0400)]
perf: Fix UAPI export of PERF_EVENT_IOC_ID

Without the following patch I have problems compiling code using
the new PERF_EVENT_IOC_ID ioctl().  It looks like u64 was used
instead of __u64

Signed-off-by: Vince Weaver <vincent.weaver@maine.edu>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1309171450380.11444@vincent-weaver-1.um.maine.edu
Signed-off-by: Ingo Molnar <mingo@kernel.org>
11 years ago9p: don't forget to destroy inode cache if fscache registration fails
Al Viro [Tue, 17 Sep 2013 12:10:18 +0000 (08:10 -0400)]
9p: don't forget to destroy inode cache if fscache registration fails

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
11 years agoMerge branch 'fixes' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Linus Torvalds [Wed, 18 Sep 2013 02:20:30 +0000 (22:20 -0400)]
Merge branch 'fixes' of git://git./virt/kvm/kvm

Pull KVM fixes from Gleb Natapov.

* 'fixes' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: VMX: set "blocked by NMI" flag if EPT violation happens during IRET from NMI
  kvm: free resources after canceling async_pf
  KVM: nEPT: reset PDPTR register cache on nested vmentry emulation
  KVM: mmu: allow page tables to be in read-only slots
  KVM: x86 emulator: emulate RETF imm

11 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Linus Torvalds [Wed, 18 Sep 2013 01:54:05 +0000 (21:54 -0400)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid

Pull HID updates from Jiri Kosina:
 "Fixes for CVE-2013-2897, CVE-2013-2895, CVE-2013-2897, CVE-2013-2894,
  CVE-2013-2893, CVE-2013-2891, CVE-2013-2890, CVE-2013-2889.

  All the bugs are triggerable only by specially crafted evil-on-purpose
  HW devices.  Fixes by Kees Cook and Benjamin Tissoires"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: lenovo-tpkbd: fix leak if tpkbd_probe_tp fails
  HID: multitouch: validate indexes details
  HID: logitech-dj: validate output report details
  HID: validate feature and input report details
  HID: lenovo-tpkbd: validate output report details
  HID: LG: validate HID output report details
  HID: steelseries: validate output report details
  HID: sony: validate HID output report details
  HID: zeroplus: validate output report details
  HID: provide a helper for validating hid reports

11 years agotty: disassociate_ctty() sends the extra SIGCONT
Oleg Nesterov [Sun, 15 Sep 2013 15:50:26 +0000 (17:50 +0200)]
tty: disassociate_ctty() sends the extra SIGCONT

Starting from v3.10 (probably commit f91e2590410b: "tty: Signal
foreground group processes in hangup") disassociate_ctty() sends SIGCONT
if tty && on_exit.  This breaks LSB test-suite, in particular test8 in
_exit.c and test40 in sigcon5.c.

Put the "!on_exit" check back to restore the old behaviour.

Review by Peter Hurley:
 "Yes, this regression was introduced by me in that commit.  The effect
  of the regression is that ptys will receive a SIGCONT when, in similar
  circumstances, ttys would not.

  The fact that two test vectors accidentally tripped over this
  regression suggests that some other apps may as well.

  Thanks for catching this"

Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Karel Srot <ksrot@redhat.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
11 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf
David S. Miller [Wed, 18 Sep 2013 00:22:53 +0000 (20:22 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/pablo/nf

Pablo Neira Ayuso says:

====================
The following patchset contains Netfilter fixes for you net tree,
mostly targeted to ipset, they are:

* Fix ICMPv6 NAT due to wrong comparison, code instead of type, from
  Phil Oester.

* Fix RCU race in conntrack extensions release path, from Michal Kubecek.

* Fix missing inversion in the userspace ipset test command match if
  the nomatch option is specified, from Jozsef Kadlecsik.

* Skip layer 4 protocol matching in ipset in case of IPv6 fragments,
  also from Jozsef Kadlecsik.

* Fix sequence adjustment in nfnetlink_queue due to using the netlink
  skb instead of the network skb, from Gao feng.

* Make sure we cannot swap of sets with different layer 3 family in
  ipset, from Jozsef Kadlecsik.

* Fix possible bogus matching in ipset if hash sets with net elements
  are used, from Oliver Smith.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agovxlan: Avoid creating fdb entry with NULL destination
Sridhar Samudrala [Tue, 17 Sep 2013 19:12:40 +0000 (12:12 -0700)]
vxlan: Avoid creating fdb entry with NULL destination

Commit afbd8bae9c798c5cdbe4439d3a50536b5438247c
   vxlan: add implicit fdb entry for default destination
creates an implicit fdb entry for default destination. This results
in an invalid fdb entry if default destination is not specified.
For ex:
  ip link add vxlan1 type vxlan id 100
creates the following fdb entry
  00:00:00:00:00:00 dev vxlan1 dst 0.0.0.0 self permanent

This patch fixes this issue by creating an fdb entry only if a
valid default destination is specified.

Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agotcp: fix RTO calculated from cached RTT
Neal Cardwell [Tue, 17 Sep 2013 01:44:20 +0000 (21:44 -0400)]
tcp: fix RTO calculated from cached RTT

Commit 1b7fdd2ab5852 ("tcp: do not use cached RTT for RTT estimation")
did not correctly account for the fact that crtt is the RTT shifted
left 3 bits. Fix the calculation to consistently reflect this fact.

Signed-off-by: Neal Cardwell <ncardwell@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-By: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agodrivers: net: phy: cicada.c: clears warning Use #include <linux/io.h> instead of...
Avinash Kumar [Mon, 16 Sep 2013 16:09:41 +0000 (21:39 +0530)]
drivers: net: phy: cicada.c: clears warning Use #include <linux/io.h> instead of <asm/io.h>

clears following warnings :
WARNING: Use include <linux/io.h> instead of <asm/io.h>
WARNING: Use include <linux/uaccess.h> instead of <asm/uaccess.h>

Signed-off-by: Avinash Kumar <avi.kp.137@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet loopback: Set loopback_dev to NULL when freed
Eric W. Biederman [Mon, 16 Sep 2013 23:52:41 +0000 (16:52 -0700)]
net loopback: Set loopback_dev to NULL when freed

It has recently turned up that we have a number of long standing bugs
in the network stack cleanup code with use of the loopback device
after it has been freed that have not turned up because in most cases
the storage allocated to the loopback device is not reused, when those
accesses happen.

Set looback_dev to NULL to trigger oopses instead of silent data corrupt
when we hit this class of bug.

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoatomic_open: take care of EEXIST in no-open case with O_CREAT|O_EXCL in fs/namei.c
Al Viro [Mon, 16 Sep 2013 23:22:33 +0000 (19:22 -0400)]
atomic_open: take care of EEXIST in no-open case with O_CREAT|O_EXCL in fs/namei.c

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
11 years agobatman-adv: set the TAG flag for the vid passed to BLA
Antonio Quartulli [Wed, 11 Sep 2013 17:14:44 +0000 (19:14 +0200)]
batman-adv: set the TAG flag for the vid passed to BLA

When receiving or sending a packet a packet on a VLAN, the
vid has to be marked with the TAG flag in order to make any
component in batman-adv understand that the packet is coming
from a really tagged network.

This fix the Bridge Loop Avoidance behaviour which was not
able to send announces over VLAN interfaces.

Introduced by 0b1da1765fdb00ca5d53bc95c9abc70dfc9aae5b
("batman-adv: change VID semantic in the BLA code")

Signed-off-by: Antonio Quartulli <antonio@open-mesh.org>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
11 years agoMIPS: Optimize current_cpu_type() for better code.
Ralf Baechle [Tue, 17 Sep 2013 08:25:47 +0000 (10:25 +0200)]
MIPS: Optimize current_cpu_type() for better code.

 o Move current_cpu_type() to a separate header file
 o #ifdefing on supported CPU types lets modern GCC know that certain
   code in callers may be discarded ideally turning current_cpu_type() into
   a function returning a constant.
 o Use current_cpu_type() rather than direct access to struct cpuinfo_mips.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5833/

11 years agoKVM: VMX: set "blocked by NMI" flag if EPT violation happens during IRET from NMI
Gleb Natapov [Sun, 15 Sep 2013 08:07:23 +0000 (11:07 +0300)]
KVM: VMX: set "blocked by NMI" flag if EPT violation happens during IRET from NMI

Set "blocked by NMI" flag if EPT violation happens during IRET from NMI
otherwise NMI can be called recursively causing stack corruption.

Signed-off-by: Gleb Natapov <gleb@redhat.com>
11 years agoMIPS: Fix accessing to per-cpu data when flushing the cache
Ralf Baechle [Tue, 17 Sep 2013 10:44:31 +0000 (12:44 +0200)]
MIPS: Fix accessing to per-cpu data when flushing the cache

This fixes the following issue

BUG: using smp_processor_id() in preemptible [00000000] code: kjournald/1761
caller is blast_dcache32+0x30/0x254
Call Trace:
[<8047f02c>] dump_stack+0x8/0x34
[<802e7e40>] debug_smp_processor_id+0xe0/0xf0
[<80114d94>] blast_dcache32+0x30/0x254
[<80118484>] r4k_dma_cache_wback_inv+0x200/0x288
[<80110ff0>] mips_dma_map_sg+0x108/0x180
[<80355098>] ide_dma_prepare+0xf0/0x1b8
[<8034eaa4>] do_rw_taskfile+0x1e8/0x33c
[<8035951c>] ide_do_rw_disk+0x298/0x3e4
[<8034a3c4>] do_ide_request+0x2e0/0x704
[<802bb0dc>] __blk_run_queue+0x44/0x64
[<802be000>] queue_unplugged.isra.36+0x1c/0x54
[<802beb94>] blk_flush_plug_list+0x18c/0x24c
[<802bec6c>] blk_finish_plug+0x18/0x48
[<8026554c>] journal_commit_transaction+0x3b8/0x151c
[<80269648>] kjournald+0xec/0x238
[<8014ac00>] kthread+0xb8/0xc0
[<8010268c>] ret_from_kernel_thread+0x14/0x1c

Caches in most systems are identical - but not always, so we can't avoid
the use of smp_call_function() by just looking at the boot CPU's data,
have to fiddle with preemption instead.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5835

11 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
Linus Torvalds [Tue, 17 Sep 2013 15:40:49 +0000 (11:40 -0400)]
Merge git://git./linux/kernel/git/cmetcalf/linux-tile

Pull more tile architecture updates from Chris Metcalf:
 "This second batch of changes is just cleanup of various kinds from
  doing some tidying work in the sources.

  Some dead code is removed, comment typos fixed, whitespace and style
  issues cleaned up, and some header updates from our internal
  "upstream" architecture team"

* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  tile: remove stray blank space
  tile: <arch/> header updates from upstream
  tile: improve gxio iorpc autogenerated code style
  tile: double default VMALLOC space
  tile: remove stale arch/tile/kernel/futex_64.S
  tile: remove HUGE_VMAP dead code
  tile: use pmd_pfn() instead of casting via pte_t
  tile: fix typos in comment in arch/tile/kernel/unaligned.c

11 years agodrm/nouveau/ttm: prevent double-free in nouveau_sgdma_create_ttm() failure path
Ben Skeggs [Tue, 17 Sep 2013 04:13:32 +0000 (14:13 +1000)]
drm/nouveau/ttm: prevent double-free in nouveau_sgdma_create_ttm() failure path

TTM calls the destructor on its own already...

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
11 years agodrm/nouveau/bios/init: fix thinko in INIT_CONFIGURE_MEM
Ben Skeggs [Tue, 17 Sep 2013 00:20:31 +0000 (10:20 +1000)]
drm/nouveau/bios/init: fix thinko in INIT_CONFIGURE_MEM

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>