[S390] dasd: fix idaw boundary checking for track based ccw

A ccw command that reads or writes several records at once will
usually transfer more data then fits into one page and needs to
address memory areas using a list of indirect data address words
(idaw). All but the first of these areas must start on a 4KB or 2KB
block boundary (depending on the idaw format).
A check for this restriction was missing and has been added with
this patch.

Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

[S390] dasd: Use the new async framework for autoonlining.

The dasd driver can automatically online detected dasds, which
especially important for finding the root device. Currently,
it will wait for each online operation to finish individually,
which may take long if many dasds need to be onlined. When using
the new async framework, these onlining operations can run in
parallel and presence of the root device is ensured by the fact
that prepare_namespace() waits for all async threads to finish.

Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

[S390] qdio: remove dead timeout handler

The QDIO ccw devices are started by ccw_device_start so no timeout
can occur for the interrupt handler. Remove the dead code.

In case of an I/O error set the device state to error and wake up
a possibly running qdio_shutdown waiter.

Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

[S390] appldata: Use new mod_virt_timer_periodic() function.

mod_virt_timer() was used to modify/add cpu timers for cpus that were
set online. This resulted in a one-shot timer for every cpu that was
newly added or previously set offline, instead of an interval timer,
which broke the appldata vtime interval setup.

To fix this, the new mod_virt_timer_periodic() function is used, which
adds interval timers instead of one-shot timers.

Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

[S390] extend virtual timer interface by mod_virt_timer_periodic

In case mod_virt_timer is used to add a non pending timer the timer
is always added as a one-shot timer. If mod_virt_timer is used for
periodic timers they may therfore be degraded to one-shot timers.

Add mod_virt_timer_periodic to the interface to allow safe re-programming
of the interval value.

Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

[S390] stp synchronization retry timer

Add a timer that retries the clock synchronization via the server time
protocol if there is a usable clock but the synchronization failed.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

[S390] call nmi_enter/nmi_exit on machine checks

nmi_enter/nmi_exit includes the lockdep calls and various
other calls which were missing so far.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

[S390] wire up preadv/pwritev system calls

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

[S390] s390: move machine flags to lowcore

Currently the storage of the machine flags is a globally exported unsigned
long long variable. By moving the storage location into the lowcore struct we
allow assembler code to check machine_flags directly even without needing a
register. Addtionally the lowcore and therefore the machine flags too will be
in cache most of the time.

Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  tomoyo: version bump to 2.2.0.
  tomoyo: add Documentation/tomoyo.txt

Fix quilt merge error in acpi-cpufreq.c

We ended up incorrectly using '&cur' instead of '&readin' in the
work_on_cpu() -> smp_call_function_single() transformation in commit
01599fca6758d2cd133e78f87426fc851c9ea725 ("cpufreq: use
smp_call_function_[single|many]() in acpi-cpufreq.c").

Andrew explains:
 "OK, the acpi tree went and had conflicting changes merged into it after
  I'd written the patch and it appears that I incorrectly reverted part
  of 18b2646fe3babeb40b34a0c1751e0bf5adfdc64c while fixing the resulting
  rejects.

  Switching it to `readin' looks correct."

Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

tomoyo: version bump to 2.2.0.

Signed-off-by: Kentaro Takeda <takedakn@nttdata.co.jp>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Toshiharu Harada <haradats@nttdata.co.jp>
Signed-off-by: James Morris <jmorris@namei.org>

tomoyo: add Documentation/tomoyo.txt

Signed-off-by: Kentaro Takeda <takedakn@nttdata.co.jp>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Toshiharu Harada <haradats@nttdata.co.jp>
Signed-off-by: James Morris <jmorris@namei.org>

Merge branch 'for-rc1/xen/core' of git://git./linux/kernel/git/jeremy/xen

* 'for-rc1/xen/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
  xen: add FIX_TEXT_POKE to fixmap
  xen: honour VCPU availability on boot
  xen: clean up gate trap/interrupt constants
  xen: set _PAGE_NX in __supported_pte_mask before pagetable construction
  xen: resume interrupts before system devices.
  xen/mmu: weaken flush_tlb_other test
  xen/mmu: some early pagetable cleanups
  Xen: Add virt_to_pfn helper function
  x86-64: remove PGE from must-have feature list
  xen: mask XSAVE from cpuid
  NULL noise: arch/x86/xen/smp.c
  xen: remove xen_load_gdt debug
  xen: make xen_load_gdt simpler
  xen: clean up xen_load_gdt
  xen: split construction of p2m mfn tables from registration
  xen: separate p2m allocation from setting
  xen: disable preempt for leave_lazy_mmu

edac: use to_delayed_work()

The edac-core driver includes code which assumes that the work_struct
which is included in every delayed_work is the first member of that
structure.  This is currently the case but might change in the future, so
use to_delayed_work() instead, which doesn't make such an assumption.

linux-2.6.30-rc1 has the to_delayed_work() function that will allow this
patch to work

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

edac: fix local pci_write_bits32

Fix the edac local pci_write_bits32 to properly note the 'escape' mask if
all ones in a 32-bit word.

Currently no consumer of this function uses that mask, so there is no
danger to existing code.

Signed-off-by: Jeff Haran <jharan@Brocade.COM>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgi-xpc: clean up numerous globals

Introduce xpc_arch_ops and eliminate numerous individual global definitions.

Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Dean Nelson <dcn@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgi-xpc: implement opencomplete messaging

sgi-xpc has a window of failure where an open message can be sent and a
subsequent data message can get lost.  We have added a new message
(opencomplete) which closes that window.

Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgi-xpc: prevent false heartbeat failures

The heartbeat timeout functionality in sgi-xpc is currently not trained to
the connection time.  If a connection is made and the code is in the last
polling window prior to doing a timeout, the next polling window will see
the heartbeat as unchanged and initiate a no-heartbeat disconnect.

Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgi-xpc: update SGI XP/XPC/XPNET maintainer

Dean has moved on to other work.  His responsibilities for XP/XPC/XPNET
have been handed to me.

Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

doc: use correct debugfs mountpoint

Use the default mountpoint of debugfs in the pktcdvd ABI.

Signed-off-by: Shen Feng <shen@cn.fujitsu.com>
Cc: <balagi@justmail.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memcg: fix documentation

The description about various statistics from memory.stat is not accurate
and confusing at times.

Correct this along with a few other minor cleanups.

Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Replace all DMA_nBIT_MASK macro with DMA_BIT_MASK(n)

This is the second go through of the old DMA_nBIT_MASK macro,and there're not
so many of them left,so I put them into one patch.I hope this is the last round.
After this the definition of the old DMA_nBIT_MASK macro could be removed.

Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg KH <greg@kroah.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ext2: fix data corruption for racing writes

If two writers allocating blocks to file race with each other (e.g.
because writepages races with ordinary write or two writepages race with
each other), ext2_getblock() can be called on the same inode in parallel.
Before we are going to allocate new blocks, we have to recheck the block
chain we have obtained so far without holding truncate_mutex.  Otherwise
we could overwrite the indirect block pointer set by the other writer
leading to data loss.

The below test program by Ying is able to reproduce the data loss with ext2
on in BRD in a few minutes if the machine is under memory pressure:

long kMemSize  = 50 << 20;
int kPageSize = 4096;

int main(int argc, char **argv) {
int status;
int count = 0;
int i;
char *fname = "/mnt/test.mmap";
char *mem;
unlink(fname);
int fd = open(fname, O_CREAT | O_EXCL | O_RDWR, 0600);
status = ftruncate(fd, kMemSize);
mem = mmap(0, kMemSize, PROT_READ | PROT_WRITE, MAP_SHARED, fd, 0);
// Fill the memory with 1s.
memset(mem, 1, kMemSize);
sleep(2);
for (i = 0; i < kMemSize; i++) {
int byte_good = mem[i] != 0;
if (!byte_good && ((i % kPageSize) == 0)) {
//printf("%d ", i / kPageSize);
count++;
}
}
munmap(mem, kMemSize);
close(fd);
unlink(fname);

if (count > 0) {
printf("Running %d bad page\n", count);
return 1;
}
return 0;
}

Cc: Ying Han <yinghan@google.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Mingming Cao <cmm@us.ibm.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

shmem: respect MAX_LFS_FILESIZE

SHMEM_MAX_BYTES was derived from the maximum size of its triple-indirect
swap vector, forgetting to take the MAX_LFS_FILESIZE limit into account.
Never mind 256kB pages, even 8kB pages on 32-bit kernels allowed files to
grow slightly bigger than that supposed maximum.

Fix this by using the min of both (at build time not run time).  And it
happens that this calculation is good as far as 8MB pages on 32-bit or
16MB pages on 64-bit: though SHMSWP_MAX_INDEX gets truncated before that,
it's truncated to such large numbers that we don't need to care.

[akpm@linux-foundation.org: it needs pagemap.h]
[akpm@linux-foundation.org: fix sparc64 min() warnings]
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Yuri Tikhonov <yur@emcraft.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

shmem: fix division by zero

Fix a division by zero which we have in shmem_truncate_range() and
shmem_unuse_inode() when using big PAGE_SIZE values (e.g.  256kB on
ppc44x).

With 256kB PAGE_SIZE, the ENTRIES_PER_PAGEPAGE constant becomes too large
(0x1.0000.0000) on a 32-bit kernel, so this patch just changes its type
from 'unsigned long' to 'unsigned long long'.

Hugh: reverted its unsigned long longs in shmem_truncate_range() and
shmem_getpage(): the pagecache index cannot be more than an unsigned long,
so the divisions by zero occurred in unreached code.  It's a pity we need
any ULL arithmetic here, but I found no pretty way to avoid it.

Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

intelfb: support i854

Support the Intel 854 Chipset in fbdev.

We test and use the patch on a Thomson IP1101 IPTV-Box.  On the VGA-Port
we get a normal signal.

Here is the link to the Mambux-Project: http://www.mambux.de

Cc: Keith Packard <keithp@keithp.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Stefan Husemann <shusemann@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: add documentation describing what tsk->active_mm means vs tsk->mm

I'm sure everyone knows this, but I didn't, so I googled it, and found a
nice explanation from Linus.  Might be worth sticking in Documentation.

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memcg: remove warning when CONFIG_DEBUG_VM=n

mm/memcontrol.c:318: warning: `mem_cgroup_is_obsolete' defined but not used

[akpm@linux-foundation.org: simplify as suggested by Balbir]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/sys.c: clean up sys_shutdown exit path

Impact: cleanup, fix

Clean up sys_shutdown() exit path.  Factor out common code.  Return
correct error code instead of always 0 on failure.

Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

at25: make input buffers of at25_*write() const

| drivers/misc/eeprom/at25.c:358: warning: assignment from incompatible pointer type

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

at24: make input buffers of at24_*write() const

| drivers/misc/eeprom/at24.c:508: warning: assignment from incompatible pointer type

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

jbd: update locking coments

Update information about locking in JBD revoke code.

Reported-by: Lin Tan <tammy000@gmail.com>.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: document get_user_pages_fast()

While better than get_user_pages(), the usage of gupf(), especially the
return values and the fact that it can potentially only partially pin the
range, warranted some documentation.

Signed-off-by: Andy Grover <andy.grover@oracle.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

initramfs: fix initramfs to work with hardlinked init

Change cb6ff208076b5f434db1b8c983429269d719cef5 ("NOMMU: Support XIP on
initramfs") seems to have broken booting from initramfs with /sbin/init
being a hardlink.

It seems like the logic required for XIP on nommu, i.e.  ftruncate to
reported cpio header file size (body_len) is broken for hardlinks, which
have a reported size of 0, and the truncate thus nukes the contents of the
file (in my case busybox), making boot impossible and ending with runaway
loop modprobe binfmt-0000 - and of course 0000 is not a valid binary
format.

My fix is to only call ftruncate if size is non-zero which fixes things
for me, but I'm not certain whether this will break XIP for those files on
nommu systems, although I would guess not.

Signed-off-by: Randy Robertson <rmrobert@vmware.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ptrace: fix exit_ptrace() vs ptrace_traceme() race

Pointed out by Roland.  The bug was recently introduced by me in
"forget_original_parent: split out the un-ptrace part", commit
39c626ae47c469abdfd30c6e42eff884931380d6.

Since that patch we have a window after exit_ptrace() drops tasklist and
before forget_original_parent() takes it again.  In this window the child
can do ptrace(PTRACE_TRACEME) and nobody can untrace this child after
that.

Change ptrace_traceme() to not attach to the exiting ->real_parent.  We
don't report the error in this case, we pretend we attach right before
->real_parent calls exit_ptrace() which should untrace us anyway.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MAINTAINERS: bluesmoke-devel list is moderated for non-subscribers

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: reformat the Unevictable-LRU documentation

Do a bit of reformatting on the Unevictable-LRU documentation.

Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: point the UNEVICTABLE_LRU config option at the documentation

Point the UNEVICTABLE_LRU config option at the documentation describing
the option.

Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sysrq: remove duplicated #include

Remove duplicated #include in drivers/char/sysrq.c.

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

include/video/cyblafb.h: remove it, it's unused

commit ddb53d48da5b0e691f35e703ac29118747f86c99 ("fbdev: remove cyblafb
driver") removed drivers/video/cyblafb.c, but not its .h file

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Jani Monoses" <jani@ubuntu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

res_counter: update documentation

After the introduction of resource counters hierarchies
(28dbc4b6a01fb579a9441c7b81e3d3413dc452df) the prototypes of
res_counter_init() and res_counter_charge() have been changed.

Keep the documentation consistent with the actual function prototypes.

Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: Paul Menage <menage@google.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi: spi_write_then_read() bugfixes

The "simplify spi_write_then_read()" patch included two regressions from
the 2.6.27 behaviors:

 - The data it wrote out during the (full duplex) read side
   of the transfer was not zeroed.

 - It fails completely on half duplex hardware, such as
   Microwire and most "3-wire" SPI variants.

So, revert that patch.  A revised version should be submitted at some
point, which can get the speedup on standard hardware (full duplex)
without breaking on less-capable half-duplex stuff.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org> [2.6.28.x, 2.6.29.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

asm-generic/siginfo.h: update NSIGTRAP definition

Impact: (nearly) trivial

The patch

commit da654b74bda14c45a7d98c731bf3c1a43b6b74e2
Author: Srinivasa Ds <srinivasa@in.ibm.com>
Date:   Tue Sep 23 15:23:52 2008 +0530

    signals: demultiplexing SIGTRAP signal

forgot to update the NSIGTRAP define in asm-generic/siginfo.h to the new
number of sigtrap subcodes.  Nothing in the tree seems to use it, but
presumably something in user space might.  So update it.

Cc: Srinivasa Ds <srinivasa@in.ibm.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

cirrusfb: do not allow unsupported pixel depth

Do not allow modes with unsupported pixel depth.  Otherwise, one can hang
a computer by setting incorrect value with fbset command.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

filemap: fix kernel-doc warnings

Fix filemap.c kernel-doc warnings:

Warning(mm/filemap.c:575): No description found for parameter 'page'
Warning(mm/filemap.c:575): No description found for parameter 'waiter'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

include/linux/fiemap.h: include types.h now that it's exported

Include <linux/types.h> in fiemap.h.  Sam Ravnborg pointed out that this
was missing in this newly-exported header which uses the __u32 and __u64
types.

Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/video/aty/radeon_base.c: fix typo in comment

Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sisfb: fix color component length for pseudocolor modes

sisfb incorrectly sets the length of the color fields to 6 bits
for PSEUDOCOLOR modes, even though 8 bits are always used per pixel.
Fix this by setting the length to 8.

Signed-off-by: Michal Januszewski <spock@gentoo.org>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sa1100fb: fix color component length for pseudocolor modes

sa1100fb incorrectly sets the length of the color fields to 8 bits for
PSEUDOCOLOR modes for which only 4 bits are used per pixel.  Fix this by
setting the length to 4 bits for these modes.

Signed-off-by: Michal Januszewski <spock@gentoo.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

s3fb: fix color component length for pseudocolor modes

s3fb incorrectly sets the length of the color fields to 6 bits for
PSEUDOCOLOR modes, even though 8 or 4 bits are used per pixel.  Fix this
by setting the length to 8 or 4, respectively.

Signed-off-by: Michal Januszewski <spock@gentoo.org>
Acked-by: Ondrej Zajicek <santiago@crfreenet.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

namespaces: move get_mq() inside #ifdef CONFIG_SYSCTL

| ipc/mq_sysctl.c:26: warning: 'get_mq' defined but not used

Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

aio: remove INIT_KIOCTX

Unused after 20dcae32439384b6863c626bb3b2a09bed65b33e aka
"[PATCH] aio: remove kioctx from mm_struct".

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hfs: fix memory leak when unmounting

When an HFS filesystem is unmounted, it leaks a 2-page bitmap.  Also,
under extreme memory pressure, it's possible that hfs_releasepage() may
use a tree pointer that has not been initialized, and if so, the release
request should just be rejected.

[akpm@linux-foundation.org: free_pages(0) is legal, remove obvious comment]
Signed-off-by: Dave Anderson <anderson@redhat.com>
Tested-by: Eugene Teo <eugeneteo@kernel.sg>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hwmon: sht15 humidity sensor driver

Data sheet at:
http://www.sensirion.ch/en/pdf/product_information/Datasheet-humidity-sensor-SHT1x.pdf

These sensors communicate over a 2 wire bus running a device specific
protocol.  The complexity of the driver is mainly due to handling the
substantial delays between requesting a reading and the device pulling the
data line low to indicate that the data is available.  This is handled by
an interrupt that is disabled under all other conditions.

I wasn't terribly clear on the best way to handle this, so comments on
that aspect would be particularly welcome!

Interpretation of the temperature depends on knowing the supply voltage.
If configured in a board config as a regulator consumer this is obtained
from the regulator subsystem.  If not it should be provided in the
platform data.

I've placed this driver in the hwmon subsystem as it is definitely a
device that may be used for hardware monitoring and with it's relatively
slow response times (up to 120 millisecs to get a reading) a caching
strategy certainly seems to make sense!

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

efifb: exit if framebuffer address is invalid

efifb will attempt to ioremap a framebuffer even if its starting address
is 0, failing and causing an ugly backtrace in the process.  Exit before
probing if this is the case.

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Peter Jones <pjones@redhat.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

uvesafb: fix color component length for pseudocolor modes

uvesafb incorrectly sets the length of the color fields to 6 bits for
PSEUDOCOLOR modes, even though 8 bits are always used per pixel.  Fix this
by setting the length to 8.

The switch of the DAC width from the default 6 bits to 8 bits is retained
and tracked internally in the driver, but never exposed to userspace.

Signed-off-by: Michal Januszewski <spock@gentoo.org>
Acked-by: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <syrjala@sci.fi>
Cc: Geert Uytterhoeven <geert.uytterhoeven@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbdev: fix color component field length documentation

The documentation about the meaning of the color component bitfield
lengths in pseudocolor modes is inconsistent.  Fix it, so that it
indicates the correct interpretation everywhere, i.e.  that 1 << length is
the number of palette entries.

Signed-off-by: Michal Januszewski <spock@gentoo.org>
Acked-by: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <syrjala@sci.fi>
Acked-by: Geert Uytterhoeven <geert.uytterhoeven@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbdev: fix info->lock deadlock in fbcon_event_notify()

fb_notifier_call_chain() is called with info->lock held, i.e.  in
do_fb_ioctl() => FBIOPUT_VSCREENINFO => fb_set_var() and the some
notifier callbacks, like fbcon_event_notify(), try to re-acquire
info->lock again.

Remove the lock/unlock_fb_info() in all the framebuffer notifier
callbacks' and be sure to always call fb_notifier_call_chain() with
info->lock held.

Reported-by: Pavel Roskin <proski@gnu.org>
Reported-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

init/initramfs: fix warning with CONFIG_BLK_DEV_RAM=n

init/initramfs.c:520: warning: 'clean_rootfs' defined but not used

Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hp_accel: remove unused #include <version.h>

Remove unused #include <version.h> in drivers/hwmon/hp_accel.c.

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Documentation/sysctl/net.txt: fix a typo

s/spicified/specified

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MAINTAINERS: fix Andreas's email address

Correct typo in email address.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MAINTAINERS: switch maintainer of the hso driver

Since Denis is no longer working for Option, I will maintain the driver from
now on.

Signed-off-by: Jan Dumon <j.dumon@option.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: move the scan_unevictable_pages sysctl to the vm table

vm knobs should go in the vm table.  Probably too late for
randomize_va_space though.

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: remove xfs_flush_space
  xfs: flush delayed allcoation blocks on ENOSPC in create
  xfs: block callers of xfs_flush_inodes() correctly
  xfs: make inode flush at ENOSPC synchronous
  xfs: use xfs_sync_inodes() for device flushing
  xfs: inform the xfsaild of the push target before sleeping
  xfs: prevent unwritten extent conversion from blocking I/O completion
  xfs: fix double free of inode
  xfs: validate log feature fields correctly

Merge git://git./linux/kernel/git/sam/kbuild-fixes

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
  docbook: make cleandocs
  kbuild: fix spurious initramfs rebuild
  Documentation: explain the difference between __bitwise and __bitwise__
  kbuild: make it possible for the linker to discard local symbols from vmlinux
  kbuild: remove pointless strdup() on arguments passed to new_module() in modpost
  kbuild: fix a few typos in top-level Makefile
  kbuild: introduce destination-y for exported headers
  kbuild: use git svn instead of git-svn in setlocalversion
  kconfig: fix update-po-config to accect backslash in input
  kbuild: fix option processing for -I in headerdep

Merge branch 'upstream-linus' of git://git./linux/kernel/git/jgarzik/libata-dev

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  ata: fix obviously wrong comment
  ahci: force CAP_NCQ for earlier NV MCPs
  [libata] sata_via: kill uninit'd var warning

Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (22 commits)
  Input: i8042 - add HP DV9700 to the noloop list
  Input: arrange drivers/input/misc/Makefile in alphabetical order
  Input: add AD7879 Touchscreen driver
  Input: add AD7877 touchscreen driver
  Input: bf54x-keys - fix typo in warning
  Input: add driver for S1 button of rb532
  Input: generic driver for rotary encoders on GPIOs
  Input: hilkbd - fix crash when removing hilkbd module
  Input: atkbd - add quirk for Fujitsu Siemens Amilo PA 1510
  Input: atkbd - consolidate force release quirk setup
  Input: add accelerated touchscreen support for Marvell Zylonite
  Input: ucb1400_ts, mainstone-wm97xx - add BTN_TOUCH events
  Input: wm97xx - use disable_irq_nosync() for Mainstone
  Input: wm97xx - add BTN_TOUCH event to wm97xx to use it with Android
  Input: fix polling of /proc/bus/input/devices
  Input: psmouse - add newline to OLPC HGPK touchpad debugging
  Input: ati_remote2 - check module params
  Input: ati_remote2 - add per device attrs
  Input: ati_remote2 - complete suspend support
  Input: stop autorepeat timer on key release
  ...

PM/Hibernate: Wait for SCSI devices scan to complete during resume

There is a race between resume from hibernation and the asynchronous
scanning of SCSI devices and to prevent it from happening we need to
call scsi_complete_async_scans() during resume from hibernation.

In addition, if the resume from hibernation is userland-driven, it's
better to wait for all device probes in the kernel to complete before
attempting to open the resume device.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge git://git.infradead.org/iommu-2.6

* git://git.infradead.org/iommu-2.6:
  intel-iommu: Avoid panic() for DRHD at address zero.
  Intel-IOMMU Alignment Issue in dma_pte_clear_range()

Merge branch 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: add linux kernel support for YMM state
  x86: fix wrong section of pat_disable & make it static
  x86: Fix section mismatches in mpparse
  x86: fix set_fixmap to use phys_addr_t
  x86: Document get_user_pages_fast()
  x86, intr-remap: fix eoi for interrupt remapping without x2apic

Merge branch 'tracing-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  tracing/filters: return proper error code when writing filter file
  tracing/filters: allow user input integer to be oct or hex
  tracing/filters: fix NULL pointer dereference
  tracing/filters: NIL-terminate user input filter
  ftrace: Output REC->var instead of __entry->var for trace format
  Make __stringify support variable argument macros too
  tracing: fix document references
  tracing: fix splice return too large
  tracing: update file->f_pos when splice(2) it
  tracing: allocate page when needed
  tracing: disable seeking for trace_pipe_raw

Merge branch 'core-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  lockdep: continue lock debugging despite some taints
  lockdep: warn about lockdep disabling after kernel taint

cpufreq: use smp_call_function_[single|many]() in acpi-cpufreq.c

Atttempting to rid us of the problematic work_on_cpu().  Just use
smp_call_fuction_single() here.

This repairs a 10% sysbench(oltp)+mysql regression which Mike reported,
due to

  commit 6b44003e5ca66a3fffeb5bc90f40ada2c4340896
  Author: Andrew Morton <akpm@linux-foundation.org>
  Date:   Thu Apr 9 09:50:37 2009 -0600

      work_on_cpu(): rewrite it to create a kernel thread on demand

It seems that the kernel calls these acpi-cpufreq functions at a quite
high frequency.

Valdis Kletnieks also reports that this causes 70-90 forks per second on
his hardware.

Cc: Valdis.Kletnieks@vt.edu
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Mike Galbraith <efault@gmx.de>
Cc: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
[ Made it use smp_call_function_many() instead of looping over cpu's
  with smp_call_function_single()    - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6

* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  i2c: Let new-style drivers implement attach_adapter
  i2c: Fix sparse warnings for I2C_BOARD_INFO()
  i2c-voodoo3: Deprecate in favor of tdfxfb
  i2c-algo-pca: Fix use of uninitialized variable in debug message

add some long-missing capabilities to fs_mask

When POSIX capabilities were introduced during the 2.1 Linux
cycle, the fs mask, which represents the capabilities which having
fsuid==0 is supposed to grant, did not include CAP_MKNOD and
CAP_LINUX_IMMUTABLE.  However, before capabilities the privilege
to call these did in fact depend upon fsuid==0.

This patch introduces those capabilities into the fsmask,
restoring the old behavior.

See the thread starting at http://lkml.org/lkml/2009/3/11/157 for
reference.

Note that if this fix is deemed valid, then earlier kernel versions (2.4
and 2.2) ought to be fixed too.

Changelog:
[Mar 23] Actually delete old CAP_FS_SET definition...
[Mar 20] Updated against J. Bruce Fields's patch

Reported-by: Igor Zhbanov <izh1979@gmail.com>
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: stable@kernel.org
Cc: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'gm_20090410' of git://repo.or.cz/linux-2.6/trivial-mods

* 'gm_20090410' of git://repo.or.cz/linux-2.6/trivial-mods:
  MAINTAINERS - Update MN10300 patterns
  MAINTAINERS - Update frv arch patterns
  scripts/get_maintainer.pl - Allow multiple files on command line
  MAINTAINERS - Update Freescale sound patterns
  MAINTAINERS - Add additional patterns
  MAINTAINERS - Add missing "/" to some pattern directories
  MAINTAINERS - Update DRIVER CORE patterns
  MAINTAINERS - Update M68K patterns
  MAINTAINERS - Coalesce sections "DVB" and "Video for Linux"
  MAINTAINERS - Remove cyblafb frame buffer no longer in tree
  MAINTAINERS - Remove x86/Voyager no longer in tree
  MAINTAINERS - Update FPU Emulator contact address and web page
  MAINTAINERS - i2c_tiny_usb T: should be W:
  MAINTAINERS - Add Linus Torvalds' git
  MAINTAINERS - standardize "T:       git urls"
  MAINTAINERS - Remove HP Fibre Channel HBA no longer in tree
  MAINTAINERS - Standardize style
  MAINTAINERS - Add file patterns
  Add scripts/get_maintainer.pl

Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Andrew Morton <akpm@linux-foundation.org>

Merge branch 'core-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  percpu: unbreak alpha percpu
  mutex: have non-spinning mutexes on s390 by default

Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds

* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
  leds: just ignore invalid GPIOs in leds-gpio

Merge git://git./linux/kernel/git/wim/linux-2.6-watchdog

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [WATCHDOG] omap_wdt.c: move probe function to .devinit.text
  [WATCHDOG] ks8695_wdt.c: move probe function to .devinit.text
  [WATCHDOG] at91rm9200_wdt.c: move probe function to .devinit.text
  [WATCHDOG] remove ARM26 sections
  [WATCHDOG] orion5x_wdt: Add shutdown callback, use watchdog ping function
  [WATCHDOG] i6300esb.c: Restructure initialization of the device
  [WATCHDOG] i6300esb.c: Fix the GETSTATUS and GETBOOTSTATUS ioctls.
  [WATCHDOG] i6300esb.c: Cleanup

Merge branch 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze

* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze: (60 commits)
  microblaze_v8: Add MAINTAINERS fragment
  microblaze_v8: Uartlite for Microblaze
  microblaze_v8: Makefiles for Microblaze cpu
  microblaze_v8: Kconfig patches
  microblaze_v8: Interrupt handling and timer support
  microblaze_v8: syscalls.h
  microblaze_v8: pci headers
  microblaze_v8: Kbuild file
  microblaze_v8: string.h thread_info.h
  microblaze_v8: unistd.h
  microblaze_v8: fcntl.h sockios.h ucontext.h
  microblaze_v8: pool.h socket.h
  microblaze_v8: device.h param.h topology.h
  microblaze_v8: headers files entry.h current.h mman.h registers.h sembuf.h
  microblaze_v8: namei.h
  microblaze_v8: gpio.h, serial.h
  microblaze_v8: headers simple files - empty or redirect to asm-generic
  microblaze_v8: sigcontext.h siginfo.h
  microblaze_v8: termbits.h termios.h
  microblaze_v8: stats headers
  ...

i2c: Let new-style drivers implement attach_adapter

While it isn't the way the standard device binding model works, it is
OK for new-style drivers to implement attach_adapter. It may help
convert the renaming legacy drivers to new style drivers faster.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>

i2c: Fix sparse warnings for I2C_BOARD_INFO()

Since the first argument to I2C_BOARD_INFO() must be a string constant,
there is no need to parenthesise it, and adding parentheses results in
an invalid initialiser for char[].  gcc obviously accepts this syntax as
an extension, but sparse complains, e.g.:

drivers/net/sfc/boards.c:173:2: warning: array initialized from parenthesized string constant

Therefore, remove the parentheses.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

i2c-voodoo3: Deprecate in favor of tdfxfb

Support for I2C/DDC was recently added to the tdfxfb driver, which
means that the i2c-voodoo3 driver can be deprecated.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>

i2c-algo-pca: Fix use of uninitialized variable in debug message

A recent change broke debugging of pca_xfer(), fix it.

Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>

ata: fix obviously wrong comment

Also remove the now-useless debug printouts which are supposed to
tell us when the scan starts and ends.

Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ahci: force CAP_NCQ for earlier NV MCPs

Along with MCP65, MCP67 and 73 also don't set CAP_NCQ.  Force it.
Reported by zaceni@yandex.ru on bko#13014 and confirmed by Peer Chen.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: NightFox <zaceni2@yandex.ru>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

[libata] sata_via: kill uninit'd var warning

Reported and initial patch by Marin Mitov.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

lockdep: continue lock debugging despite some taints

Impact: broaden lockdep checks

Lockdep is disabled after any kernel taints. This might be convenient
to ignore bad locking issues which sources come from outside the kernel
tree. Nevertheless, it might be a frustrating experience for the
staging developers or those who experience a warning but are focused
on another things that require lockdep.

The v2 of this patch simply don't disable anymore lockdep in case
of TAINT_CRAP and TAINT_WARN events.

Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: LTP <ltp-list@lists.sourceforge.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Greg KH <gregkh@suse.de>
LKML-Reference: <1239412638-6739-2-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

lockdep: warn about lockdep disabling after kernel taint

Impact: provide useful missing info for developers

Kernel taint can occur in several situations such as warnings,
load of prorietary or staging modules, bad page, etc...

But when such taint happens, a developer might still be working on
the kernel, expecting that lockdep is still enabled. But a taint
disables lockdep without ever warning about it.
Such a kernel behaviour doesn't really help for kernel development.

This patch adds this missing warning.

Since the taint is done most of the time after the main message that
explain the real source issue, it seems safe to warn about it inside
add_taint() so that it appears at last, without hurting the main
information.

v2: Use a generic helper to disable lockdep instead of an
    open coded xchg().

Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <1239412638-6739-1-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: add linux kernel support for YMM state

Impact: save/restore Intel-AVX state properly between tasks

Intel Advanced Vector Extensions (AVX) introduce 256-bit vector processing
capability. More about AVX at http://software.intel.com/sites/avx

Add OS support for YMM state management using xsave/xrstor infrastructure
to support AVX.

Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1239402084.27006.8057.camel@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: fix wrong section of pat_disable & make it static

pat_disable cannot be __cpuinit anymore because it's called from pat_init
and the callchain looks like this:
pat_disable [cpuinit] <- pat_init <- generic_set_all <-
 ipi_handler <- set_mtrr <- (other non init/cpuinit functions)

WARNING: arch/x86/mm/built-in.o(.text+0x449e): Section mismatch in reference
from the function pat_init() to the function .cpuinit.text:pat_disable()
The function pat_init() references
the function __cpuinit pat_disable().
This is often because pat_init lacks a __cpuinit
annotation or the annotation of pat_disable is wrong.

Non CONFIG_X86_PAT version of pat_disable is static inline, so this version
can be static too (and there are no callers outside of this file).

Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <49DFB055.6070405@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: Fix section mismatches in mpparse

Impact: fix section mismatch

In arch/x86/kernel/mpparse.c, smp_reserve_bootmem() has been called
and also refers to a function which is in .init section. Thus causes
the first warning. And check_irq_src() also requires an __init,
because it refers to an .init section.

Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <b9df5fa10904102004g51265d9axc8d07278bfdb6ba0@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

tracing/filters: return proper error code when writing filter file

- propagate return value of filter_add_pred() to the user

- return -ENOSPC but not -ENOMEM or -EINVAL when the filter array
  is full

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Tom Zanussi <tzanussi@gmail.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <49E04CF0.3010105@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

tracing/filters: allow user input integer to be oct or hex

Before patch:

 # echo 'parent_pid == 0x10' > events/sched/sched_process_fork/filter
 # cat sched/sched_process_fork/filter
 parent_pid == 0

After patch:

 # cat sched/sched_process_fork/filter
 parent_pid == 16

Also check the input more strictly.

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Tom Zanussi <tzanussi@gmail.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <49E04C53.4010600@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

tracing/filters: fix NULL pointer dereference

Try this, and you'll see NULL pointer dereference bug:

  # echo -n 'parent_comm ==' > sched/sched_process_fork/filter

Because we passed NULL ptr to simple_strtoull().

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Tom Zanussi <tzanussi@gmail.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <49E04C43.1050504@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

tracing/filters: NIL-terminate user input filter

Make sure messages from user space are NIL-terminated strings,
otherwise we could dump random memory while reading filter file.

Try this:
 # echo 'parent_comm ==' > events/sched/sched_process_fork/filter
 # cat events/sched/sched_process_fork/filter
 parent_comm == �

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Tom Zanussi <tzanussi@gmail.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <49E04C32.6060508@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Revert "ACPI battery: fix async boot oops"

This reverts commit 5d38258ec026921a7b266f4047ebeaa75db358e5, since the
underlying problem got fixed properly in the previous commit ("async:
Fix module loading async-work regression").

Cc: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

async: Fix module loading async-work regression

Several drivers use asynchronous work to do device discovery, and we
synchronize with them in the compiled-in case before we actually try to
mount root filesystems etc.

However, when compiled as modules, that synchronization is missing - the
module loading completes, but the driver hasn't actually finished
probing for devices, and that means that any user mode that expects to
use the devices after the 'insmod' is now potentially broken.

We already saw one case of a similar issue in the ACPI battery code,
where the kernel itself expected the module to be all done, and unmapped
the init memory - but the async device discovery was still running.
That got hacked around by just removing the "__init" (see commit
5d38258ec026921a7b266f4047ebeaa75db358e5 "ACPI battery: fix async boot
oops"), but the real fix is to just make the module loading wait for all
async work to be completed.

It will slow down module loading, but since common devices should be
built in anyway, and since the bug is really annoying and hard to handle
from user space (and caused several S3 resume regressions), the simple
fix to wait is the right one.

This fixes at least

http://bugzilla.kernel.org/show_bug.cgi?id=13063

but probably a few other bugzilla entries too (12936, for example), and
is confirmed to fix Rafael's storage driver breakage after resume bug
report (no bugzilla entry).

We should also be able to now revert that ACPI battery fix.

Reported-and-tested-by: Rafael J. Wysocki <rjw@suse.com>
Tested-by: Heinz Diehl <htd@fancy-poultry.org>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>