GitHub/moto-9609/android_kernel_motorola_exynos9610.git
8 years agonet_sched: drop packets after root qdisc lock is released
Eric Dumazet [Wed, 22 Jun 2016 06:16:49 +0000 (23:16 -0700)]
net_sched: drop packets after root qdisc lock is released

Qdisc performance suffers when packets are dropped at enqueue()
time because drops (kfree_skb()) are done while qdisc lock is held,
delaying a dequeue() draining the queue.

Nominal throughput can be reduced by 50 % when this happens,
at a time we would like the dequeue() to proceed as fast as possible.

Even FQ is vulnerable to this problem, while one of FQ goals was
to provide some flow isolation.

This patch adds a 'struct sk_buff **to_free' parameter to all
qdisc->enqueue(), and in qdisc_drop() helper.

I measured a performance increase of up to 12 %, but this patch
is a prereq so that future batches in enqueue() can fly.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoMerge branch 'liquidio-next'
David S. Miller [Sat, 25 Jun 2016 16:08:41 +0000 (12:08 -0400)]
Merge branch 'liquidio-next'

Raghu Vatsavayi says:

====================
liquidio: updates and bug fixes

Please consider following patch series for liquidio bug fixes
and updates on top of net-next. Following patches should be
applied in the following order as some of them depend on
earlier patches in the series.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoliquidio: ddr timeout
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:15 +0000 (22:53 -0700)]
liquidio: ddr timeout

Adds support for ddr_timeout during device init.

Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoliquidio: Support priv flag
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:14 +0000 (22:53 -0700)]
liquidio: Support priv flag

This patch adds support for private flags for the driver.

Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoliquidio: ptp info
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:13 +0000 (22:53 -0700)]
liquidio: ptp info

This patch has minor changes for proper ptp info retreival.

Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoliquidio: New xaui info
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:12 +0000 (22:53 -0700)]
liquidio: New xaui info

This patch adds support for host driver support for new Xaui
interfaces.

Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoliquidio: New statistics support
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:11 +0000 (22:53 -0700)]
liquidio: New statistics support

This patch adds extensive support of statistics for data path,
control path and firmware.

Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoliquidio: tx rx interrupt moderation
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:10 +0000 (22:53 -0700)]
liquidio: tx rx interrupt moderation

This patch has new tx/rx interrupt moderation defaults of
count/timer for better throughput and utilisation.

Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoliquidio: chip reset changes
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:09 +0000 (22:53 -0700)]
liquidio: chip reset changes

This patch resolves the order of chip reset while destroying
the resources by postoponing soft reset in destroy resources
function until all queues are removed properly.

Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoliquidio: New unload state
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:08 +0000 (22:53 -0700)]
liquidio: New unload state

This patch adds new state so that the ctrl packets are not sent
to firmware during unload time and only rx packets are allowed.

Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoliquidio: Firmware image download
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:07 +0000 (22:53 -0700)]
liquidio: Firmware image download

This patch has firmware image related changes for: firmware
release upon failure, support latest firmware version and
firmware download in 4MB chunks.

Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoliquidio: Napi rx/tx traffic
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:06 +0000 (22:53 -0700)]
liquidio: Napi rx/tx traffic

This Patch adds tx buffer handling  to Napi along with RX
traffic. Also separate spinlocks are introduced for handling
iq posting and buffer reclaim so that tx path and tx interrupt
do not compete against each other.

Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoliquidio: Vlan filtering
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:05 +0000 (22:53 -0700)]
liquidio: Vlan filtering

This patch adds supports for Vlan filtering for liquidio driver.

Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoliquidio: Vlan offloads changes
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:04 +0000 (22:53 -0700)]
liquidio: Vlan offloads changes

This patch adds support for vlan offloads for the driver and
receive header structures are also modified appropriately. Also
requestID will not be used in reveive header any more.

Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoliquidio: soft command buffer limits
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:03 +0000 (22:53 -0700)]
liquidio: soft command buffer limits

This patch increases the limits of soft command buffer size and
num command buffers. This patch also has changes for queue macros
and limit related changes for new chips.

Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agocxgb4vf: Synchronize access to mailbox
Hariprasad Shenai [Wed, 22 Jun 2016 04:09:29 +0000 (09:39 +0530)]
cxgb4vf: Synchronize access to mailbox

The issue comes when there are multiple threads attempting to use the
mailbox facility at the same time. The issue is the for the Virtual
Function Driver, the only way to get the Virtual Interface statistics
is to issue mailbox commands to ask the firmware for the VI Stats.
And, because the VI Stats command can only retrieve a smallish number of
stats per mailbox command, we have to issue three mailbox commands in quick
succession. When ethtool or netstat command to get interface stats and
interface up/down is run in a loop for every 0.1 sec, we observed
mailbox collisions. And out of the two commands one would fail with
the present code, since we don't queue the second command.

To overcome the above issue, added a queue to access the mailbox.
Whenever a mailbox command is issued add it to the queue. If its at the
head issue the mailbox command, else wait for the existing command to
complete. Usually command takes less than a milli-second to complete.
Also timeout from the loop, if the command under execution takes
long time to run.

In reality, the number of mailbox access collisions is going to be very
rare since no one runs such abusive script.

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agosamples/bpf: set max locked memory to ulimited
William Tu [Wed, 22 Jun 2016 04:05:58 +0000 (21:05 -0700)]
samples/bpf: set max locked memory to ulimited

Signed-off-by: William Tu <u9012063@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: ethernet: macb: use phy_ethtool_{get|set}_link_ksettings
Philippe Reynes [Tue, 21 Jun 2016 22:32:36 +0000 (00:32 +0200)]
net: ethernet: macb: use phy_ethtool_{get|set}_link_ksettings

There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: ethernet: macb: use phydev from struct net_device
Philippe Reynes [Tue, 21 Jun 2016 22:32:35 +0000 (00:32 +0200)]
net: ethernet: macb: use phydev from struct net_device

The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoopenvswitch: Only set mark and labels with a commit flag.
Jarno Rajahalme [Tue, 21 Jun 2016 21:59:38 +0000 (14:59 -0700)]
openvswitch: Only set mark and labels with a commit flag.

Only set conntrack mark or labels when the commit flag is specified.
This makes sure we can not set them before the connection has been
persisted, as in that case the mark and labels would be lost in an
event of an userspace upcall.

OVS userspace already requires the commit flag to accept setting
ct_mark and/or ct_labels.  Validate for this in the kernel API.

Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoopenvswitch: Set mark and labels before confirming.
Jarno Rajahalme [Tue, 21 Jun 2016 21:59:37 +0000 (14:59 -0700)]
openvswitch: Set mark and labels before confirming.

Set conntrack mark and labels right before committing so that
the initial conntrack NEW event has the mark and labels.

Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: dsa: mv88e6xxx: rename single-chip support
Vivien Didelot [Tue, 21 Jun 2016 16:28:20 +0000 (12:28 -0400)]
net: dsa: mv88e6xxx: rename single-chip support

With the upcoming support for cross-chip operations, it will be hard to
distinguish portions of code supporting a single-chip or a switch fabric
of interconnected chips.

Make the code clearer now, by renaming the mv88e6xxx_priv_state chip
structure to mv88e6xxx_chip. This patch brings no functional changes.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: dsa: mv88e6xxx: move driver in its own folder
Vivien Didelot [Tue, 21 Jun 2016 16:28:19 +0000 (12:28 -0400)]
net: dsa: mv88e6xxx: move driver in its own folder

With the upcoming support for cross-chip operations and other mv88e6xxx
enhancements, new files will be added.

Similarly to mlxsw or b53, move mv88e6xxx files into their own folder.

In the meantime, update the MAINTAINERS entry to please checkpatch.pl,
by replacing the invalid 88E6352 entry with 88E6XXX, maintained by
Andrew and myself.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoMerge branch 'qed-coalesce'
David S. Miller [Thu, 23 Jun 2016 19:56:54 +0000 (15:56 -0400)]
Merge branch 'qed-coalesce'

Sudarsana Reddy Kalluru says:

====================
qed*: coalesce parameters config support.

The patch series adds the support for config/read of the adapter coalesce
parameters. Patch (1) adds the qed infrastructure/APIs for the support and
patch (2) adds the driver support for following ethtool commands:
ethtool -c|--show-coalesce ethX
ethtool -C|--coalesce ethX [rx-usecs N] [tx-usecs N]
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoqede: Add support for coalescing config read/update.
Sudarsana Reddy Kalluru [Tue, 21 Jun 2016 13:36:22 +0000 (09:36 -0400)]
qede: Add support for coalescing config read/update.

Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoqed: Add support for coalescing config read/update.
Sudarsana Reddy Kalluru [Tue, 21 Jun 2016 13:36:21 +0000 (09:36 -0400)]
qed: Add support for coalescing config read/update.

This patch adds support for configuring the device tx/rx coalescing
timeout values in the order of micro seconds. It also adds APIs for
upper layer drivers for reading/updating the coalescing values.

Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoMerge tag 'wireless-drivers-next-for-davem-2016-06-21' of git://git.kernel.org/pub...
David S. Miller [Thu, 23 Jun 2016 19:40:31 +0000 (15:40 -0400)]
Merge tag 'wireless-drivers-next-for-davem-2016-06-21' of git://git./linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers patches for 4.8

Major changes:

ath10k

* enable btcoex support without restarting firmware
* enable ipq4019 support using AHB bus
* add QCA9887 chipset support
* retrieve calibration data from EEPROM, currently only for QCA9887

wil6210

* add pm_notify handling

brcmfmac

* add support for the PCIE devices 43525 and 43465
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet/mlx4_en: Add DCB PFC support through CEE netlink commands
Rana Shahout [Tue, 21 Jun 2016 09:43:59 +0000 (12:43 +0300)]
net/mlx4_en: Add DCB PFC support through CEE netlink commands

This patch adds support for reading and updating priority flow
control (PFC) attributes in the driver via netlink.

Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: dsa: b53: Fix statistics readings
Florian Fainelli [Tue, 21 Jun 2016 01:26:53 +0000 (18:26 -0700)]
net: dsa: b53: Fix statistics readings

Due to a typo we would always be using the MIB counter width of the
first element of the counter array instead of the current element, and
we would always be accessing the register statistics with a 64-bits
read, while some could be 32-bits. This got unnoticed in testing with
MDIO and SRAB which tolerate doing this, but testing with the SPI bus
revealed bogus values being returned. Fix this by using the proper
iterator here.

Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Reported-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoof_mdio: Enable fixed PHY support if driver is a module
Ben Hutchings [Tue, 21 Jun 2016 00:17:17 +0000 (01:17 +0100)]
of_mdio: Enable fixed PHY support if driver is a module

The fixed_phy driver doesn't have to be built-in, and it's
important that of_mdio supports it even if it's a module.

Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoti_cpsw: Check for disabled child nodes
Ben Hutchings [Tue, 21 Jun 2016 00:16:31 +0000 (01:16 +0100)]
ti_cpsw: Check for disabled child nodes

Dual MAC devices don't necessarily have both MACs wired up, so ignore
those that are disabled.

Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoopenvswitch: Add packet len info to upcall.
William Tu [Mon, 20 Jun 2016 14:26:17 +0000 (07:26 -0700)]
openvswitch: Add packet len info to upcall.

The commit f2a4d086ed4c ("openvswitch: Add packet truncation support.")
introduces packet truncation before sending to userspace upcall receiver.
This patch passes up the skb->len before truncation so that the upcall
receiver knows the original packet size. Potentially this will be used
by sFlow, where OVS translates sFlow config header=N to a sample action,
truncating packet to N byte in kernel datapath. Thus, only N bytes instead
of full-packet size is copied from kernel to userspace, saving the
kernel-to-userspace bandwidth.

Signed-off-by: William Tu <u9012063@gmail.com>
Cc: Pravin Shelar <pshelar@nicira.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: ethernet: bgmac: use phy_ethtool_{get|set}_link_ksettings
Philippe Reynes [Sun, 19 Jun 2016 20:37:06 +0000 (22:37 +0200)]
net: ethernet: bgmac: use phy_ethtool_{get|set}_link_ksettings

There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: ethernet: bgmac: use phydev from struct net_device
Philippe Reynes [Sun, 19 Jun 2016 20:37:05 +0000 (22:37 +0200)]
net: ethernet: bgmac: use phydev from struct net_device

The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: ethernet: altera_tse: use phy_ethtool_{get|set}_link_ksettings
Philippe Reynes [Sat, 18 Jun 2016 14:37:21 +0000 (16:37 +0200)]
net: ethernet: altera_tse: use phy_ethtool_{get|set}_link_ksettings

There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: ethernet: altera_tse: use phydev from struct net_device
Philippe Reynes [Sat, 18 Jun 2016 14:37:20 +0000 (16:37 +0200)]
net: ethernet: altera_tse: use phydev from struct net_device

The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: ethernet: sun4i-emac: use phy_ethtool_{get|set}_link_ksettings
Philippe Reynes [Sat, 18 Jun 2016 13:15:40 +0000 (15:15 +0200)]
net: ethernet: sun4i-emac: use phy_ethtool_{get|set}_link_ksettings

There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: ethernet: sun4i-emac: use phydev from struct net_device
Philippe Reynes [Sat, 18 Jun 2016 13:15:39 +0000 (15:15 +0200)]
net: ethernet: sun4i-emac: use phydev from struct net_device

The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoMerge branch 'mlxsw-next'
David S. Miller [Tue, 21 Jun 2016 09:02:55 +0000 (05:02 -0400)]
Merge branch 'mlxsw-next'

Jiri Pirko says:

====================
mlxsw: Preparation for IPv4 router

Ido says:

This series prepares the driver for IPv4 router support. The router follow-up
patches are available at: https://github.com/jpirko/linux_mlxsw/tree/net-next_queue

Patches 1-9 simplify the netdevice notification block and also add several
checks during PRECHANGEUPPER events against topologies that aren't supported by
the device. This will ensure L3 interfaces are only configured on top of
valid netdevs.

Patches 10-13 contain trivial changes required for the introduction of a generic
FID struct - currently only used for vFIDs - in patch 14. Making the FID
struct generic will allow us to easily associate the underlying FIDs with
their L3-counterparts - Router interfaces (RIFs):

    FID Type        | Used by                         | RIF Type
    --------------------------------------------------------
    FID             | The VLAN-aware bridge           | VLAN
    vFID            | VLAN-unaware bridges            | FID
    rFID            | non-bridged netdevs (follow-up) | Sub-port

Obligatory ASCII art to visualize the above:

                   A.B.C.D
                      +
                      | FID RIF
                      +
                     br0                    E.F.G.H
                      +                        +
                      |                        | VLAN RIF
            +---------+---------+              +
            |                   |            br1.W
            | vFID              |              +
            |                   |              |
 vPort    +-+-+               +-+-+            +
swXpY.Z   |   |               |   |           br1
          +-+-+               +-+-+            +
            |                   |     FID=W    |
            |                   | +------------+------------+
            |                   | |                         |
        +---+---+           +---+-+-+                   +---+---+
        |       |           |       |                   |       |
        |       |           |       |                   |       |
        |       |           |       |                   |       |
        +-------+           +-------+                   +-------+
          swXpY

Patches 15-16 further generalize the struct by exploiting the fact that the
FID is a shared resource among ports. Each FID type is assigned a 'leave'
function that is invoked based on CHANGEUPPER events and takes care of the
necessary clean-up.

Patches 17-22 build upon the previous patches and use the FID struct for the
VLAN-aware bridge and take care of cleaning up FID resources in the 'leave'
functions. For now, these are only FDB records, but later on we'll have to
remove the RIFs associated with these FIDs, which will in turn take care of
routes and neighbours clean-up.

The last patch adds debug prints that proved very useful during the
development of this series.

Tested with the existing L2 recipes:
https://github.com/jpirko/lnst/tree/master/recipes/switchdev
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Add debug prints
Ido Schimmel [Mon, 20 Jun 2016 21:04:21 +0000 (23:04 +0200)]
mlxsw: spectrum: Add debug prints

For debug purposes, it's useful to know the order in which the driver
responds to changes in the topology of its upper devices.

Add debug prints to signal these events.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Free resources upon vPort destruction
Ido Schimmel [Mon, 20 Jun 2016 21:04:20 +0000 (23:04 +0200)]
mlxsw: spectrum: Free resources upon vPort destruction

There are situations in which a vPort is destroyed while still holding
references to device's resources such as FIDs and FDB records. This can
happen, for example, when a VLAN device is deleted while still being
bridged.

Instead of trying to make sure vPort destruction is invoked when it no
longer uses device's resources, just free them upon destruction. This
simplifies the code, as we no longer need to take different situations
into account when events are received - cleanup is taken care of in one
place.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Refactor FDB flushing logic
Ido Schimmel [Mon, 20 Jun 2016 21:04:19 +0000 (23:04 +0200)]
mlxsw: spectrum: Refactor FDB flushing logic

FDB entries are learned using {Port / LAG ID, FID} and therefore should
be flushed whenever a port (vPort) leaves its FID (vFID).

However, when the bridge port is a LAG device (or a VLAN device on top),
then FDB flushing is conditional. Ports removed from such LAG
configurations must not trigger flushing, as other ports might still be
members in the LAG and therefore the bridge port is still active.

The decision whether to flush or not was previously computed in the
netdevice notification block, but in order to flush the entries when a
port leaves its FID this decision should be computed there.

Strip the notification block from this logic and instead move it to one
FDB flushing function that is invoked from both the FID / vFID leave
functions.

When port isn't member in LAG, FDB flushing should always occur.
Otherwise, it should occur only when the last port (vPort) member in the
LAG leaves the FID (vFID).

This will allow us - in the next patch - to simplify the cleanup code
paths that are hit whenever the topology above the port netdevs changes.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Don't count on FID being present
Ido Schimmel [Mon, 20 Jun 2016 21:04:18 +0000 (23:04 +0200)]
mlxsw: spectrum: Don't count on FID being present

Not all vPorts will have FIDs assigned to them, so make sure functions
first test for FID presence.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Add FID get / set functions
Ido Schimmel [Mon, 20 Jun 2016 21:04:17 +0000 (23:04 +0200)]
mlxsw: spectrum: Add FID get / set functions

As previously explained, not all vPorts will be assigned FIDs, so instead
of returning the FID index of a vPort, return a pointer to its FID
struct. This will allow us to know whether it's legal to access the
vPort's FID parameters such as index and device.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Check if port is vPort using its VID
Ido Schimmel [Mon, 20 Jun 2016 21:04:16 +0000 (23:04 +0200)]
mlxsw: spectrum: Check if port is vPort using its VID

When L3 interfaces will be introduced a vPort won't necessarily have a
FID assigned to it. This can happen if it's not member in a bridge (in
which case it's assigned a vFID) or doesn't have an IP address (in which
case it's assigned an rFID).

Therefore, instead check the VID parameter to test whether a port is a
vPort or not.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Use per-FID struct for the VLAN-aware bridge
Ido Schimmel [Mon, 20 Jun 2016 21:04:15 +0000 (23:04 +0200)]
mlxsw: spectrum: Use per-FID struct for the VLAN-aware bridge

In a very similar way to the vFIDs, make the first 4K FIDs - used in the
VLAN-aware bridge - use the new FID struct.

Upon first use of the FID by any of the ports do the following:

1) Create the FID
2) Setup a matching flooding entry
3) Create a mapping for the FID

Unlike vFIDs, upon creation of a FID we always create a global
VID-to-FID mapping, so that ports without upper vPorts can use it
instead of creating an explicit {Port, VID} to FID mapping.

When a port leaves a FID the reverse is performed. Whenever the FID's
reference count reaches zero the FID is deleted along with the global
mapping.

The per-FID struct will later allow us to configure L3 interfaces on top
of the VLAN-aware bridge.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Remove unused function argument
Ido Schimmel [Mon, 20 Jun 2016 21:04:14 +0000 (23:04 +0200)]
mlxsw: spectrum: Remove unused function argument

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Use join / leave functions for vFID operations
Ido Schimmel [Mon, 20 Jun 2016 21:04:13 +0000 (23:04 +0200)]
mlxsw: spectrum: Use join / leave functions for vFID operations

When a vPort is created or when it joins a bridge we always do the same
set of operations:

1) Create the vFID, if not already created
2) Setup flooding for the vFID
3) Map the {Port, VID} to the vFID

When a vPort is destroyed or when it leaves a bridge the reverse is
performed.

Encapsulate the above in join / leave functions and simplify the code.
FIDs and rFIDs will use a similar set of functions.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Make vFID struct generic
Ido Schimmel [Mon, 20 Jun 2016 21:04:12 +0000 (23:04 +0200)]
mlxsw: spectrum: Make vFID struct generic

Up until now we had a dedicated struct only for vFIDs, but before
introducing support for L3 interfaces we need to make it generic and
use it for all three types of FIDs:

1) FIDs - 0..4K-1, used for the VLAN-aware bridge
2) vFIDs - 4K..15K-1, used for VLAN-unaware bridges
3) rFIDs - 15K..16K-1, used to direct traffic to / from the router in
the device. Will be introduced later in the series.

The three types of L3 interfaces - Router InterFaces, RIFs - that will
be introduced correspond to the three types of FIDs and are configured
using them. Therefore, we'll need to store the links between them as
well as a reference count on the underlying FID, so that the
corresponding RIF will be destroyed when it reaches zero.

Note that the lower 0.5K vFIDs are currently used for for non-bridged
netdevs, so that traffic could be flooded to the CPU port. However, when
rFIDs will be introduced we'll no longer need these and they too will be
used for VLAN-unaware bridges.

Make the vFID struct generic by renaming it and some of its fields. FIDs
will be converted to use it later in the series.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Use FID instead of vFID to setup flooding
Ido Schimmel [Mon, 20 Jun 2016 21:04:11 +0000 (23:04 +0200)]
mlxsw: spectrum: Use FID instead of vFID to setup flooding

Use a FID index instead of vFID and ease the transition towards a
generic FID struct.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Create a function to map vPort's FID
Ido Schimmel [Mon, 20 Jun 2016 21:04:10 +0000 (23:04 +0200)]
mlxsw: spectrum: Create a function to map vPort's FID

A FID used by a vPort (vFID, but also rFID later in the series) is
always mapped using {Port, VID} and not only VID as with the 4K FIDs of
the VLAN-aware bridge.

Instead of specifying all the arguments each time, just wrap this
operation using a dedicated function and simplify the code.

As before, the function takes FID as its argument in preparation for a
generic FID struct.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Use only one function to create vFIDs
Ido Schimmel [Mon, 20 Jun 2016 21:04:09 +0000 (23:04 +0200)]
mlxsw: spectrum: Use only one function to create vFIDs

Simplify the code and use only one function for vFID creation /
destruction.

Unlike before, the function receives a FID index as its argument and not
a vFID index. Instead of passing 0, now one would need to pass 4K, which
is the first vFID.

This is the first step in creating a generic FID struct that will be
used for all three types of FIDs.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Remove redundant function argument
Ido Schimmel [Mon, 20 Jun 2016 21:04:08 +0000 (23:04 +0200)]
mlxsw: spectrum: Remove redundant function argument

In all call sites 'only_uc' is set to false, so strip it.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Use DECLARE_BITMAP() macro
Ido Schimmel [Mon, 20 Jun 2016 21:04:07 +0000 (23:04 +0200)]
mlxsw: spectrum: Use DECLARE_BITMAP() macro

There is a macro to do this kind of declarations, so use it.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Centralize VLAN-aware bridge ref counting
Ido Schimmel [Mon, 20 Jun 2016 21:04:06 +0000 (23:04 +0200)]
mlxsw: spectrum: Centralize VLAN-aware bridge ref counting

We hold a reference count on the number of ports member in the
VLAN-aware bridge, as we only support one.

Instead of always incrementing / decrementing the reference count after
joining / leaving the bridge, simply do this accounting in the join /
leave functions.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Remove unnecessary function argument
Ido Schimmel [Mon, 20 Jun 2016 21:04:05 +0000 (23:04 +0200)]
mlxsw: spectrum: Remove unnecessary function argument

The argument 'br_dev' is never used, so remove it.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Make unlinking functions return void
Ido Schimmel [Mon, 20 Jun 2016 21:04:04 +0000 (23:04 +0200)]
mlxsw: spectrum: Make unlinking functions return void

When responding to unlinking CHANGEUPPER notifications we shouldn't
return any value, as it's not checked by upper layers.

In addition, there's nothing the driver can do in case of failure, so it
should simply continue and try to free as much resources as possible and
not stop on first error.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Use WARN_ON() return value
Ido Schimmel [Mon, 20 Jun 2016 21:04:03 +0000 (23:04 +0200)]
mlxsw: spectrum: Use WARN_ON() return value

Instead of checking for a condition and then issue the warning, just do
it in one go and simplify the code.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Remove unnecessary checks from event processing
Ido Schimmel [Mon, 20 Jun 2016 21:04:02 +0000 (23:04 +0200)]
mlxsw: spectrum: Remove unnecessary checks from event processing

When upper device of a VLAN device changes we already made sure it's
a bridge device in PRECHANGEUPPER, so no need to check it's a master
device in CHANGEUPPER.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Forbid LAG slave from having VLAN uppers
Ido Schimmel [Mon, 20 Jun 2016 21:04:01 +0000 (23:04 +0200)]
mlxsw: spectrum: Forbid LAG slave from having VLAN uppers

When a port netdev is put under LAG it cannot have VLAN upper devices,
so forbid that. The LAG device itself can have VLAN upper devices.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Sanitize port netdev upper devices
Ido Schimmel [Mon, 20 Jun 2016 21:04:00 +0000 (23:04 +0200)]
mlxsw: spectrum: Sanitize port netdev upper devices

We currently only support the following upper devices for port netdevs:
1) Bridge
2) LAG (bond / team)
3) VLAN

Any other device is forbidden, so return an error.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agomlxsw: spectrum: Use notifier_from_errno() in notifier block
Ido Schimmel [Mon, 20 Jun 2016 21:03:59 +0000 (23:03 +0200)]
mlxsw: spectrum: Use notifier_from_errno() in notifier block

Instead of checking the error value and returning NOTIFY_BAD, just use
notifier_from_errno() and simplify the code.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoMerge branch 'hns-next'
David S. Miller [Tue, 21 Jun 2016 08:52:02 +0000 (04:52 -0400)]
Merge branch 'hns-next'

Yisen Zhuang says:

====================
net: hns: fix some bugs in hns driver

This series includes some bugs fixed. All these patches needs to be
applied after the patchset about ACPI support, so this series is
floated to net-next list.

The patches are:
 > from Daode, fixes about pfc pause frame, getting coaslesce, led
control logic, TSO on|off and tcam table configuration.

 > from Jun He, fix the potential leak to port unavailable

 > from Kejian, fix bug of loopback and failing to test ping6

 > from Qianqian, fix the several typo in hns driver

For more details, please see individual patches.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: hns: bug fix about TSO on|off when there is traffic
Daode Huang [Tue, 21 Jun 2016 03:56:39 +0000 (11:56 +0800)]
net: hns: bug fix about TSO on|off when there is traffic

When enable/disable tso, the driver tries to access the hardware register,
but this operation will cause the port unavalible when there is traffic.
This patch tries to enable TSO when initialize, then control tso through
TSE bit in transmit descriptor.

Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: hns: change the default coalesce usecs
Daode Huang [Tue, 21 Jun 2016 03:56:38 +0000 (11:56 +0800)]
net: hns: change the default coalesce usecs

The default coalesce timeout is 3us, which is will cause CPU
usage is too high. This patch change it to 50us in order to reduce
CPU usage and the value makes sure network latency also meets requirement.

Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: hns: fix sbm default parameters config error
Daode Huang [Tue, 21 Jun 2016 03:56:37 +0000 (11:56 +0800)]
net: hns: fix sbm default parameters config error

The default sbm config parameter leaves little buffer when there is heavy
traffic, which will cause packets drop. This patch changes them to make
enough buffers for handling packets.

Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: hns: fix bug that alloc skb fail lead to port unavailable
Jun He [Tue, 21 Jun 2016 03:56:36 +0000 (11:56 +0800)]
net: hns: fix bug that alloc skb fail lead to port unavailable

When hns_nic_poll_rx_skb alloc skb fail, it will break receive cycle and
read new fbd_num to start new receive cycle. It recomputes cycle num is
fbd_num minus clean_count, actually this cycle num is too big because
it drop out receive cycle. It brings about the port unavailable.

So we will goto out when alloc skb fail to fix this bug.

Signed-off-by: Jun He <hjat2005@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: hns: bug fix about led control logic when link down
Daode Huang [Tue, 21 Jun 2016 03:56:35 +0000 (11:56 +0800)]
net: hns: bug fix about led control logic when link down

The default driver sets anchor led bit to 0 when link down,
actually, the anchor bit should be set to 1, so fixes it when
link status is down.
Secondly, change the return value of cpld_set_led_id to 0, which
means leave the cpld to control led blink frequece other than the
driver itself.

Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: hns: delete redundancy ring enable operations
Daode Huang [Tue, 21 Jun 2016 03:56:34 +0000 (11:56 +0800)]
net: hns: delete redundancy ring enable operations

When network interface is enabled, the ring enable operation is
conducted twice. This patch deletes the redundancy code of ring enable,
and integrates hnae_ae_ops.toggle_queue_status other functions to
hns_ae_start.

Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: hns: add get_coalesce_range api for hns
Daode Huang [Tue, 21 Jun 2016 03:56:33 +0000 (11:56 +0800)]
net: hns: add get_coalesce_range api for hns

This patch adds get_coalesce_range api for hns, it shows
range of coalesce usecs and frames that can be set on
this interface.

Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: hns: fix bug of getting the wrong tcam data
Daode Huang [Tue, 21 Jun 2016 03:56:32 +0000 (11:56 +0800)]
net: hns: fix bug of getting the wrong tcam data

The current driver stores the high bit value of tcam data register
to the tcam data low element, stores the low bit value of tcam data
register to tcam data high element, this patch fixes this bug.

Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: hns: add spin lock for tcam table operation
Daode Huang [Tue, 21 Jun 2016 03:56:31 +0000 (11:56 +0800)]
net: hns: add spin lock for tcam table operation

This patch adds spin lock for tcam table operation,
there maybe a race condition happens when more than
one thread try to change the tcam talbe entries.

Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: hns: bugfix about pfc pause frame statistics
Daode Huang [Tue, 21 Jun 2016 03:56:30 +0000 (11:56 +0800)]
net: hns: bugfix about pfc pause frame statistics

For SoC hip06, PFC pause handled in dsaf, while hip05 in XGMAC,
so change the statistics of pfc pause in dsaf and remove the old
pfc pause frame statistics.

Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: hns: fix the wrong speed for bond
Qianqian Xie [Tue, 21 Jun 2016 03:56:29 +0000 (11:56 +0800)]
net: hns: fix the wrong speed for bond

For debug-ports,there are two non-synchronized processes:
Speed-Auto-Negotiation and Link-Update-Status. The two
processes are towed by two different state machines.
Bond reads the speed when link up, but the speed maybe
not update the right value at that time.That make for bond's
wrong speed. Thus only one state machine should be used and
if phy_state_machine is used, it does not need to do
hns_nic_update_link_status().

Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: hns: fix ethtool loopback fail bug
Kejian Yan [Tue, 21 Jun 2016 03:56:28 +0000 (11:56 +0800)]
net: hns: fix ethtool loopback fail bug

When run ethtool cmd(ethtool -t ethx) again and again for a long
time, it will be probabilistically fail. The PHYs' registers may
be on different pages, so it must be switch to the right page
before setting PHYs' registers.
And __lb_up() calls phy_start() to startup the PHYs device, but
this function may change Copper Control Register(Page 0, Register 0)
to an other value. It would cause phy loopback test fail. if we
remove phy_start(), we have to remove the relative phy_stop(),
phy_disconnect() when doing phy loopback to keep the phy stay in
right status.

Reported-by: hejun <hjat2005@huawei.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: hns: select Hilink before serdes loopback for HNS V2
Kejian Yan [Tue, 21 Jun 2016 03:56:27 +0000 (11:56 +0800)]
net: hns: select Hilink before serdes loopback for HNS V2

As Hilink3 and Hilink4 use the same xge training and xge u adaptor for
HNSv2, it needs to select which Hilink to be set before relative serdes
being configed. The hilink_access_sel is the register to do that.

Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: hns: fix the error info when dma_set_mask_and_coherent fail
Qianqian Xie [Tue, 21 Jun 2016 03:56:26 +0000 (11:56 +0800)]
net: hns: fix the error info when dma_set_mask_and_coherent fail

The error info should be printed as "set mask to 64bit fail!" instead of
"set mask to 32bit fail!" in dma_set_mask_and_coherent().

Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: hns: Remove unnecessary device resource free
Qianqian Xie [Tue, 21 Jun 2016 03:56:25 +0000 (11:56 +0800)]
net: hns: Remove unnecessary device resource free

The driver uses devm_ioremap_resource, it will unmap the map
automatically, remove the unnecessary the resource free.

Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: hns: typo fix of annotation info for hns_nic_reset_subtask()
Qianqian Xie [Tue, 21 Jun 2016 03:56:24 +0000 (11:56 +0800)]
net: hns: typo fix of annotation info for hns_nic_reset_subtask()

The annotation info for hns_nic_reset_subtask() should be
"for resetting subtask" instead of "for resetting suntask".

Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: hns: add skb_reset_mac_header() after skb being alloc
Kejian Yan [Tue, 21 Jun 2016 03:56:23 +0000 (11:56 +0800)]
net: hns: add skb_reset_mac_header() after skb being alloc

HNS receives a packet without doing anything, but it should call
skb_reset_mac_header() to initialize the header before using
eth_hdr().

Fixes: 0d6b425a3773c3445b0f51b2f333821beaacb619
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: hns: fix hns dsaf v1 dont support tx_pause close
Qianqian Xie [Tue, 21 Jun 2016 03:56:22 +0000 (11:56 +0800)]
net: hns: fix hns dsaf v1 dont support tx_pause close

For service port, hns dsaf v1 support to close tx_pause.
However, the port will be invalid when it run command
ethtool to close tx_pause. This patch will fix it.

Signed-off-by: Qianqian Xie <xieqiaqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: hns: bug fix of ge reset sequence
Qianqian Xie [Tue, 21 Jun 2016 03:56:21 +0000 (11:56 +0800)]
net: hns: bug fix of ge reset sequence

The bit fileds of PPE reset register are different between HNS v1 and
HNS v2, but the current procedure just only match HNS v1. Here is a
patch to fix it.

Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoMerge branch 'dsa-mv88e6xxx-probe-compatible'
David S. Miller [Tue, 21 Jun 2016 07:58:36 +0000 (03:58 -0400)]
Merge branch 'dsa-mv88e6xxx-probe-compatible'

Vivien Didelot says:

====================
net: dsa: mv88e6xxx: probe compatible

This patchset factorizes the legacy and new SMI probing and abstracts
the switch register accesses. This simplifies adding support for new
chips or alternative register accesses.

This will allow us to use a compatible chip info to describe how to
access the SMI device and its switch ID register at probe time.

For the legacy probe, we fix the compatible info to 88E6085. For the
MDIO probe, we will use the compatible info from the device node data.

All patches are reviewed.

Changes since v4:

  - fix debug printing (was 'val' instead of '*val')

Changes since v3 [3]:

  - better register access abstraction using the chip structure

Changes since v2 [2]:

  - do not guess compatible model in legacy probe
  - add low level SMI API using a chip structure
  - allocate before probe and detection
  - add 3 cosmetic patches

Changes since v1 [1]:

  - merge style fix from Ben Dooks
  - add Acked-by/Reviewed-by tags
  - drop one compatible string per model
  - detect the SMI device based on the compatible info
  - add an SMI ops structure

[1] https://lkml.org/lkml/2016/6/8/1201
[2] https://lkml.org/lkml/2016/6/14/671
[3] https://lkml.org/lkml/2016/6/17/995
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: dsa: mv88e6xxx: abstract switch registers accesses
Vivien Didelot [Mon, 20 Jun 2016 17:14:11 +0000 (13:14 -0400)]
net: dsa: mv88e6xxx: abstract switch registers accesses

When the SMI address of the switch chip is zero, the chip assumes to be
the only one on the SMI master bus and thus responds to all its known
SMI devices addresses (port registers, Global2, etc.)

When its SMI address is not zero, some chips (e.g. 88E6352) use an
indirect access through two SMI Command and Data registers.

Other models (e.g. 88E6060) using less than 16 internal SMI addresses
always use a direct access.

Add a capability flag to describe chips supporting the (indirect)
Multi-chip Addressing Mode, and a low-level API to access the registers
via SMI.

Other accesses (like Ethernet management frames) may be added later.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: dsa: mv88e6xxx: add port base address to info
Vivien Didelot [Mon, 20 Jun 2016 17:14:10 +0000 (13:14 -0400)]
net: dsa: mv88e6xxx: add port base address to info

The switch ID is located at address 0x3 of every Port Registers bank.

But not all Marvell switches have their Port Registers SMI Addresses
starting at 0x10. 88E6060 starts at 0x8 and 88E6390 starts at 0x0.

Add this data in the info structure and use it in the detection code.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: dsa: mv88e6xxx: pass compatible info
Vivien Didelot [Mon, 20 Jun 2016 17:14:09 +0000 (13:14 -0400)]
net: dsa: mv88e6xxx: pass compatible info

After allocating the chip structure, pass it a compatible info pointer.

The compatible info structure will be used later to describe how to
access the switch registers and where to read the switch ID.

For the standard MDIO probe, get it from the device node data. For the
legacy DSA driver probing, pass it the 88E6085 info.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: dsa: mv88e6xxx: add detection helper
Vivien Didelot [Mon, 20 Jun 2016 17:14:08 +0000 (13:14 -0400)]
net: dsa: mv88e6xxx: add detection helper

Extract the common detection code which assigns the info structure to
the chip given the read switch ID.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: dsa: mv88e6xxx: add SMI init helper
Vivien Didelot [Mon, 20 Jun 2016 17:14:07 +0000 (13:14 -0400)]
net: dsa: mv88e6xxx: add SMI init helper

Add an helper function to isolate SMI specific assignments and checks.

This function will later help choosing the different SMI accesses based
of the compatible info.

Since the chip structure is already allocated in the legacy probe, use
the mv88e6xxx_reg_read access routine instead of __mv88e6xxx_reg_read.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: dsa: mv88e6xxx: add chip allocation helper
Vivien Didelot [Mon, 20 Jun 2016 17:14:06 +0000 (13:14 -0400)]
net: dsa: mv88e6xxx: add chip allocation helper

Add an helper function to allocate the chip structure at the beginning
of the probe functions. It will be used to initialize the SMI access.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: dsa: mv88e6xxx: rename smi_mutex to reg_lock
Vivien Didelot [Mon, 20 Jun 2016 17:14:05 +0000 (13:14 -0400)]
net: dsa: mv88e6xxx: rename smi_mutex to reg_lock

The chip smi_mutex mutex is used to protect the access to the internal
switch registers, not only the Multi-chip Addressing Mode, as commented.

Since we will isolate SMI-specific pieces of code, avoid the confusion
now by renaming smi_mutex to reg_lock. No functional changes here.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: dsa: mv88e6xxx: remove table args in info lookup
Vivien Didelot [Mon, 20 Jun 2016 17:14:04 +0000 (13:14 -0400)]
net: dsa: mv88e6xxx: remove table args in info lookup

The mv88e6xxx_table array and the mv88e6xxx_lookup_info function are
static, so remove the table and size arguments from the lookup function.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: dsa: mv88e6xxx: use gpio get optional variant
Vivien Didelot [Mon, 20 Jun 2016 17:14:03 +0000 (13:14 -0400)]
net: dsa: mv88e6xxx: use gpio get optional variant

Use the optional variant to get the reset GPIO line, instead of checking
for the -ENOENT error.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: dsa: mv88e6xxx: add switch register helpers
Vivien Didelot [Mon, 20 Jun 2016 17:14:02 +0000 (13:14 -0400)]
net: dsa: mv88e6xxx: add switch register helpers

The mixed assignments, allocations and registrations in the probe code
make it hard to follow the logic and figure out what is DSA or chip
specific.

Extract the struct dsa_switch related code in a simple
mv88e6xxx_register_switch helper function.

For symmetry in the code, add a mv88e6xxx_unregister_switch function.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: dsa: mv88e6xxx: do not increment bus refcount
Vivien Didelot [Mon, 20 Jun 2016 17:14:01 +0000 (13:14 -0400)]
net: dsa: mv88e6xxx: do not increment bus refcount

The MDIO device probe and remove functions are respectively incrementing
and decrementing the bus refcount themselves. Since these bus level
actions are out of the device scope, remove them.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: dsa: mv88e6xxx: use already declared variables
Vivien Didelot [Mon, 20 Jun 2016 17:14:00 +0000 (13:14 -0400)]
net: dsa: mv88e6xxx: use already declared variables

In the MDIO probing function, dev is already assigned to &mdiodev->dev
and np is already assigned to mdiodev->dev.of_node, so use them.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: dsa: mv88e6xxx: remove redundant assignments
Vivien Didelot [Mon, 20 Jun 2016 17:13:59 +0000 (13:13 -0400)]
net: dsa: mv88e6xxx: remove redundant assignments

The chip->ds and ds->slave_mii_bus assignments are common to both legacy
and new MDIO probing and are already done in the later setup code.

Remove the duplicated assignments from the MDIO probing code.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: dsa: mv88e6xxx: fix style issues
Vivien Didelot [Mon, 20 Jun 2016 17:13:58 +0000 (13:13 -0400)]
net: dsa: mv88e6xxx: fix style issues

This patch fixes 5 style problems reported by checkpatch:

    WARNING: suspect code indent for conditional statements (8, 24)
    #492: FILE: drivers/net/dsa/mv88e6xxx.c:492:
    + if (phydev->link)
    + reg |= PORT_PCS_CTRL_LINK_UP;

    CHECK: Logical continuations should be on the previous line
    #1318: FILE: drivers/net/dsa/mv88e6xxx.c:1318:
    +      oldstate == PORT_CONTROL_STATE_FORWARDING)
    +     && (state == PORT_CONTROL_STATE_DISABLED ||

    CHECK: multiple assignments should be avoided
    #1662: FILE: drivers/net/dsa/mv88e6xxx.c:1662:
    + vlan->vid_begin = vlan->vid_end = next.vid;

    WARNING: line over 80 characters
    #2097: FILE: drivers/net/dsa/mv88e6xxx.c:2097:
    +        const struct switchdev_obj_port_vlan *vlan,

    WARNING: suspect code indent for conditional statements (16, 32)
    #2734: FILE: drivers/net/dsa/mv88e6xxx.c:2734:
    + if (mv88e6xxx_6352_family(ps) || mv88e6xxx_6351_family(ps) ||
    [...]
    + reg |= PORT_CONTROL_EGRESS_ADD_TAG;

    total: 0 errors, 3 warnings, 2 checks, 3805 lines checked

It also rebases and integrates changes sent by Ben Dooks [1]:

    The driver has a number of functions that are not exported or
    declared elsewhere, so make them static to avoid the following
    warnings from sparse:

    drivers/net/dsa/mv88e6xxx.c:113:5: warning: symbol 'mv88e6xxx_reg_read' was not declared. Should it be static?
    drivers/net/dsa/mv88e6xxx.c:167:5: warning: symbol 'mv88e6xxx_reg_write' was not declared. Should it be static?
    drivers/net/dsa/mv88e6xxx.c:231:5: warning: symbol 'mv88e6xxx_set_addr' was not declared. Should it be static?
    drivers/net/dsa/mv88e6xxx.c:367:6: warning: symbol 'mv88e6xxx_ppu_state_init' was not declared. Should it be static?
    drivers/net/dsa/mv88e6xxx.c:3157:5: warning: symbol 'mv88e6xxx_phy_page_read' was not declared. Should it be static?
    drivers/net/dsa/mv88e6xxx.c:3169:5: warning: symbol 'mv88e6xxx_phy_page_write' was not declared. Should it be static?
    drivers/net/dsa/mv88e6xxx.c:3583:26: warning: symbol 'mv88e6xxx_switch_driver' was not declared. Should it be static?
    drivers/net/dsa/mv88e6xxx.c:3621:5: warning: symbol 'mv88e6xxx_probe' was not declared. Should it be static?

[1] http://patchwork.ozlabs.org/patch/632708/

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: ethernet: bcmsysport: use phy_ethtool_{get|set}_link_ksettings
Philippe Reynes [Sun, 19 Jun 2016 18:39:09 +0000 (20:39 +0200)]
net: ethernet: bcmsysport: use phy_ethtool_{get|set}_link_ksettings

There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: ethernet: bcmsysport: use phydev from struct net_device
Philippe Reynes [Sun, 19 Jun 2016 18:39:08 +0000 (20:39 +0200)]
net: ethernet: bcmsysport: use phydev from struct net_device

The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: ethernet: nb8800: use phy_ethtool_{get|set}_link_ksettings
Philippe Reynes [Sat, 18 Jun 2016 21:16:55 +0000 (23:16 +0200)]
net: ethernet: nb8800: use phy_ethtool_{get|set}_link_ksettings

There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>