drm/amdgpu/sdma4: Enable sdma poll mem addr on vega10 for SRIOV

While doing flr on VFs, there is possibility to lost the doorbell
writing for sdma, so enable poll mem for sdma, then sdma fw would
check the pollmem holding wptr.

Signed-off-by: Frank Min <Frank.Min@amd.com>
Signed-off-by: Xiangliang.Yu <Xiangliang.Yu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/uvd7: optimize uvd initialization sequence for SRIOV

1.Since in sriov there is no need of decoding, so skip the related code;
2.Vcpu boot up and umc enable need to take at the end of the init sequence;

Signed-off-by: Frank Min <Frank.Min@amd.com>
Signed-off-by: Xiangliang.Yu <Xiangliang.Yu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/vce4: optimize vce 4.0 init table sequence for SRIOV

Optimize init table sequence for sriov.

Signed-off-by: Frank Min <Frank.Min@amd.com>
Signed-off-by: Xiangliang.Yu <Xiangliang.Yu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: According hardware design revert vce and uvd doorbell assignment

Now uvd doorbell is from 0xf8-0xfb and vce doorbell is from 0xfc-0xff

Signed-off-by: Frank Min <Frank.Min@amd.com>
Signed-off-by: Xiangliang.Yu <Xiangliang.Yu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Skip uvd and vce ring test for SRIOV

Since rptr would not be accessed on later secure asics in sriov, remove
the ring test.

Signed-off-by: Frank Min <Frank.Min@amd.com>
Signed-off-by: Xiangliang.Yu <Xiangliang.Yu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/vce4: Remove vce interrupt enable related code for sriov

Interrupt enable is contained in vce init table and this register could
not be accessed in secure ASICs, so just remove it.

Signed-off-by: Frank Min <Frank.Min@amd.com>
Signed-off-by: Xiangliang.Yu <Xiangliang.Yu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Enable uvd and vce gpu re-init for SRIOV gpu reset

Add uvd and vce re-init after gpu reset.

Signed-off-by: Frank Min <Frank.Min@amd.com>
Signed-off-by: Xiangliang.Yu <Xiangliang.Yu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Clear vce&uvd ring wptr for SRIOV

MMSCH FW need to get the wptr from 0 after it get the mailbox request
from driver, since every time kick the mailbox, mmsch thinks that it
is the first time engine start to initialize.

Signed-off-by: Frank Min <Frank.Min@amd.com>
Signed-off-by: Xiangliang.Yu <Xiangliang.Yu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Add support for filling a buffer with 64 bit value

That function will be used later to support setting a page table
block with 64 bit value.

Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: disable vcn power control for now

The dpm control for vcn has been moved to firmware, kernel always spins
"amdgpu: [powerplay] pp_dpm_powergate_uvd was not implemented", each
time when application runs, disable it for now till pg/cg. Also remove
clock manual setting when dpm disabled, which was inherited from uvd.

Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/dce_virtual: remove error message for vega10

Vega10 also support virtual display, remove the error message.

Signed-off-by: Xiangliang.Yu <Xiangliang.Yu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Merge tag 'drm-misc-next-2017-08-08' of git://anongit.freedesktop.org/git/drm-misc into drm-next

UAPI Changes:
- vc4: Add ioctl to allow attaching a label to a bo (Eric)
- Add new format/modifier blob plane property (Ben)
- armada: Use __u32/__u64 instead of uint32_t/uint64_t (Mikko)
- [kinda uapi] fb_helper: Expose display_info size via fb_info (David)

Core Changes:
- Default gem_dumb_[map_offset|destroy] as mmap/destroy implementations (Noralf)
- Simplify atomic properties by removing the helpers and handling in core (Daniel)

Driver Changes:
- stm: Add STM32 DSI controller driver (Phillipe)
- vc4: Add HDMI CEC support (Hans)
- rockchip: Refactor register init & soc version handling (Mark)
- misc: Remove .load_lut, .gamma_set, .gamma_get dead code (Peter)
- dw-hdmi: Add HDMI CEC support (Russell)

Cc: Philippe CORNU <philippe.cornu@st.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Mark yao <mark.yao@rock-chips.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: David Lechner <david@lechnology.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
* tag 'drm-misc-next-2017-08-08' of git://anongit.freedesktop.org/git/drm-misc: (107 commits)
  drm: Nuke drm_atomic_legacy_backoff
  drm: Nuke drm_atomic_helper_connector_dpms
  drm: Nuke drm_atomic_helper_connector_set_property
  drm: Nuke drm_atomic_helper_plane_set_property
  drm: Nuke drm_atomic_helper_crtc_set_property
  drm: Handle properties in the core for atomic drivers
  drm: Don't update property values for atomic drivers
  drm/omap: Rework the rotation-on-crtc hack
  drm/radeon: Use the drm_driver.dumb_destroy default
  drm/i915: Use the drm_driver.dumb_destroy default
  drm/sti: Use .dumb_map_offset and .dumb_destroy defaults
  drm: bridge: synopsys/dw-hdmi: Provide default configuration function for HDMI 2.0 PHY
  drm/fb-helper: pass physical dimensions to fbdev
  uapi drm/armada_drm.h: use __u32 and __u64 instead of uint32_t and uint64_t
  drm/bridge: dw-hdmi: remove CEC engine register definitions
  drm/bridge: dw-hdmi: add cec driver
  drm/bridge: dw-hdmi: add missing cec_notifier_put
  drm: remove unused and redundant callbacks
  staging: vboxvideo: remove dead gamma lut code
  drm: dw-hdmi-i2s: add missing company name on Copyright
  ...

drm: Nuke drm_atomic_legacy_backoff

Finally all users are gone!

Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-9-daniel.vetter@ffwll.ch

drm: Nuke drm_atomic_helper_connector_dpms

It's dead code, the core handles all this directly now.

The only special case is nouveau and tda988x which used one function
for both legacy modeset code and -nv50 atomic world instead of 2
vtables. But amounts to exactly the same.

v2: Rebase over the panel/brideg refactorings in stm/ltdc.

Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Peter Senna Tschudin <peter.senna@collabora.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Yakir Yang <kuankuan.y@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Romain Perier <romain.perier@collabora.com>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Hai Li <hali@codeaurora.org>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-tegra@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Cc: zain wang <wzz@rock-chips.com>
Cc: Baoyou Xie <baoyou.xie@linaro.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-8-daniel.vetter@ffwll.ch
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Philippe Cornu <philippe.cornu@st.com> (on stm)
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Vincent Abriou <vincent.abriou@st.com>

drm: Nuke drm_atomic_helper_connector_set_property

It's dead code, the core handles all this directly now. This also
allows us to unexport drm_atomic_helper_connector_set_property.

The only special case is nouveau which used one function for both
pre-nv50 legacy modeset code and post-nv50 atomic world instead of 2
vtables. But amounts to exactly the same.

What is rather strange here is how few drivers set this up, I suspect
the earlier patch to handle properties in the core did end up fixing a
pile of possible issues.

Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: intel-gfx@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-7-daniel.vetter@ffwll.ch
Acked-by: Vincent Abriou <vincent.abriou@st.com>

drm: Nuke drm_atomic_helper_plane_set_property

It's dead code, the core handles all this directly now. This also
allows us to unexport drm_atomic_plane_set_property.

Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Eric Engestrom <eric@engestrom.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-6-daniel.vetter@ffwll.ch
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Acked-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

drm: Nuke drm_atomic_helper_crtc_set_property

It's dead code because this is now handled in the core.

Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Eric Engestrom <eric@engestrom.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Sushmita Susheelendra <ssusheel@codeaurora.org>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: intel-gfx@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-5-daniel.vetter@ffwll.ch
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Acked-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>

drm: Handle properties in the core for atomic drivers

The reason behind the original indirection through the helper
functions was to allow existing drivers to overwrite how they handle
properties. For example when a vendor-specific userspace had
expectations that didn't match atomic. That seemed likely, since
atomic is standardizing a _lot_ more of the behaviour of a kms driver.

But 20 drivers later there's no such need at all. Worse, this forces
all drivers to hook up the default behaviour, breaking userspace if
they forget to do that. And it forces us to export a bunch of core
function just for those helpers.

And finally, these helpers are the last places using
drm_atomic_legacy_backoff() and the implicit acquire_ctx.

This patch here just implements the new behaviour and updates the
docs. Follow-up patches will garbage-collect all the dead code.

v2: Fixup docs even better!

v3: Make it actually work ...

v4: Drop the uses_atomic_modeset() checks from the previous patch
again, since they're now moved up in the callchain.

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org> (v3)
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725120204.2107-1-daniel.vetter@ffwll.ch

drm: Don't update property values for atomic drivers

Atomic drivers only use the property value store for immutable (i.e.
can't be set by userspace, but the kernel can still adjust it)
properties. The only tricky part is the removal of the update in
drm_atomic_helper_update_legacy_modeset_state().

This was added in

commit 8c10342cb48f3140d9abeadcfd2fa6625d447282 (tag: topic/drm-misc-2015-07-28)
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date:   Mon Jul 27 13:24:29 2015 +0200

    drm/atomic: Update legacy DPMS state during modesets, v3.

by copying it from the i915 code, where it was originally added in

commit 68d3472047a572936551f8ff0b6f4016c5a1fdef
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Thu Sep 6 22:08:35 2012 +0200

    drm/i915: update dpms property in set_mode

for the legacy modeset code. The reason we needed this hack was that
i915 didn't yet set DRIVER_ATOMIC, and we checked for that instead of
the newer-ish drm_drv_uses_atomic_modeset(), which avoids such
troubles. With the correct feature checks this isn't needed anymore at
all.

Also make sure that drivers don't accidentally get this wrong by
making the exported version of drm_object_property_get_value() only
work for legacy drivers. Only gma500 uses it anyway.

v2: Fixup the uses_atomic_modeset() checks (Maarten)

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725120137.1903-1-daniel.vetter@ffwll.ch

drm/omap: Rework the rotation-on-crtc hack

I want/need to rework the core property handling, and this hack is
getting in the way. But since it's a non-standard propety only used by
legacy userspace we know that this will only every be called from
ioctl code. And never on some other free-standing state struct, where
this old hack wouldn't work either.

v2: don't forget zorder and get_property!

v3: Shadow the legacy state to avoid locking issues in get_property
(Maarten).

v4: Review from Laurent
- Move struct omap_crtc_state into omap_crtc.c
- Clean up comments.
- Don't forget to copy the shadowed state over on duplicate.

v5: Don't forget to update the reset handler (Maarten).
v6: Update omap_crtc_state shadow values in omap_crtc_atomic_check (Maarten).
v7:
- Fix get_property to return 0 and set value in *val (Maarten).
- Update comment in set_property for changes in v6 (Maarten).

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> (v4)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> (v4)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/a6a10a4f-2ebc-5f81-00bd-5e906967f384@linux.intel.com

drm/radeon: Use the drm_driver.dumb_destroy default

drm_gem_dumb_destroy() is the drm_driver.dumb_destroy default,
so no need to set it.

Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1502034068-51384-16-git-send-email-noralf@tronnes.org

drm/i915: Use the drm_driver.dumb_destroy default

drm_gem_dumb_destroy() is the drm_driver.dumb_destroy default,
so no need to set it.

Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1502034068-51384-12-git-send-email-noralf@tronnes.org

drm/sti: Use .dumb_map_offset and .dumb_destroy defaults

This driver can use the drm_driver.dumb_destroy and
drm_driver.dumb_map_offset defaults, so no need to set them.

Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1502034068-51384-5-git-send-email-noralf@tronnes.org

drm: bridge: synopsys/dw-hdmi: Provide default configuration function for HDMI 2.0 PHY

Currently HDMI 2.0 PHYs do not have a default configuration function.

As *some* of the HDMI 2.0 PHYs have the same register layout as the 3D
PHYs we can provide the same default configuration function for both
and still let user overwrite this with custom configuration function
if needed.

If, for some reason, the PHY is custom or has a register different
register layout then custom configuration function *must* be provided
in order for the system to work correctly. As we prefer the pdata
provided configuration function over the internal one this change
will not make any impact in custom platforms.

Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Tested-by: Mark Yao <mark.yao@rock-chips.com>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Heiko Stübner <heiko@sntech.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/185ccf7d4473fa557044732402ca20b3d4007952.1498209896.git.joabreu@synopsys.com

drm/fb-helper: pass physical dimensions to fbdev

The fbdev subsystem has a place for physical dimensions (width and height
in mm) that is readable by userspace. Since DRM also knows these
dimensions, pass this information to the fbdev device.

This has to be done in drm_setup_crtcs_fb() instead of drm_setup_crtcs()
because fb_helper->fbdev may be NULL in drm_setup_crtcs().

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1501863924-7154-1-git-send-email-david@lechnology.com

uapi drm/armada_drm.h: use __u32 and __u64 instead of uint32_t and uint64_t

These are defined in linux/types.h or drm/drm.h. Fixes
user space compilation errors like:

drm/armada_drm.h:26:2: error: unknown type name ‘uint32_t’
  uint32_t handle;
  ^~~~~~~~

Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Gabriel Laskar <gabriel@lse.epita.fr>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170806164428.2273-33-mikko.rapeli@iki.fi

drm/bridge: dw-hdmi: remove CEC engine register definitions

We don't need the CEC engine register definitions, so let's remove them.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170802184108.7913-5-hverkuil@xs4all.nl

drm/bridge: dw-hdmi: add cec driver

Add a CEC driver for the dw-hdmi hardware.

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[hans.verkuil: unsigned -> unsigned int]
[hans.verkuil: cec_transmit_done -> cec_transmit_attempt_done]
[hans.verkuil: add missing CEC_CAP_PASSTHROUGH]
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170802184108.7913-4-hverkuil@xs4all.nl

drm/bridge: dw-hdmi: add missing cec_notifier_put

The __dw_hdmi_remove() function was missing a call to cec_notifier_put
to balance the cec_notifier_get in the probe function.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/a7688d13-2d61-ed16-f2df-28cbb5007f38@xs4all.nl

drm: remove unused and redundant callbacks

Drivers no longer have any need for these callbacks, and there are no
users. Zap. Zap-zap-zzzap-p-pp-p.

Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170713162538.22788-15-peda@axentia.se

staging: vboxvideo: remove dead gamma lut code

The redundant fb helpers .load_lut, .gamma_set and .gamma_get are
no longer used. Remove the dead code that was not doing anything
sensible anyway.

Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170804104506.2414-1-peda@axentia.se

drm: dw-hdmi-i2s: add missing company name on Copyright

This driver's Copyright is under Renesas Solutions Corp.
This patch updates the year, because this driver was moved
into synopsys folder in 2017.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/87tw1khvnq.wl%kuninori.morimoto.gx@renesas.com

drm/bridge: dw-hdmi: add better clock disable control

The video setup path aways sets the clock disable register to a specific
value, which has the effect of disabling the CEC engine.  When we add the
CEC driver, this becomes a problem.

Fix this by only setting/clearing the bits that the video path needs to.

Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/E1dcBha-00088l-DE@rmk-PC.armlinux.org.uk

drm/bridge: dw-hdmi: add cec notifier support

Add CEC notifier support to the HDMI bridge driver, so that the CEC
part of the IP can receive its physical address.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/E1dcBhV-00088e-8x@rmk-PC.armlinux.org.uk

drm/tinydrm: remove call to mipi_dbi_init() from mipi_dbi_spi_init()

This removes the call to mipi_dbi_init() from mipi_dbi_spi_init() so that
drivers can have a driver-specific implementation if needed.

Suggested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1501799630-1650-2-git-send-email-david@lechnology.com

drm/fsl-dcu: Use .dumb_map_offset and .dumb_destroy defaults

This driver can use the drm_driver.dumb_destroy and
drm_driver.dumb_map_offset defaults, so no need to set them.

Cc: Stefan Agner <stefan@agner.ch>
Cc: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1500837417-40580-8-git-send-email-noralf@tronnes.org

drm: stm: remove dead code and pointless local lut storage

The redundant fb helper .load_lut is no longer used, and can not
work right without also providing the fb helpers .gamma_set and
.gamma_get thus rendering the code in this driver suspect.

Just remove the dead code.

Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170713162538.22788-14-peda@axentia.se

drm: radeon: remove dead code and pointless local lut storage

The redundant fb helpers .load_lut, .gamma_set and .gamma_get are
no longer used. Remove the dead code and hook up the crtc .gamma_set
to use the crtc gamma_store directly instead of duplicating that
info locally.

Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170713162538.22788-13-peda@axentia.se

drm: nouveau: remove dead code and pointless local lut storage

The redundant fb helpers .load_lut, .gamma_set and .gamma_get are
no longer used. Remove the dead code and hook up the crtc .gamma_set
to use the crtc gamma_store directly instead of duplicating that
info locally.

Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170713162538.22788-12-peda@axentia.se

drm: mgag200: remove dead code and pointless local lut storage

The redundant fb helpers .load_lut, .gamma_set and .gamma_get are
no longer used. Remove the dead code and hook up the crtc .gamma_set
to use the crtc gamma_store directly instead of duplicating that
info locally.

Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170713162538.22788-11-peda@axentia.se

drm: i915: remove dead code and pointless local lut storage

The driver stores lut values from the fbdev interface, and is able
to give them back, but does not appear to do anything with these
lut values. The generic fb helpers have replaced this function,
and may even have made the driver work for the C8 mode from the
fbdev interface. But that is untested.

Since the fb helpers .gamma_set and .gamma_get are obsolete,
remove the dead code.

Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170713162538.22788-10-peda@axentia.se

drm: gma500: remove dead code and pointless local lut storage

The redundant fb helpers .gamma_set and .gamma_get are no longer
used. Remove the dead code and hook up the crtc .gamma_set
to use the crtc gamma_store directly instead of duplicating that
info locally.

Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170713162538.22788-9-peda@axentia.se

drm: cirrus: remove dead code and pointless local lut storage

The redundant fb helpers .load_lut, .gamma_set and .gamma_get are
no longer used. Remove the dead code and hook up the crtc .gamma_set
to use the crtc gamma_store directly instead of duplicating that
info locally.

Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170713162538.22788-8-peda@axentia.se

drm: ast: remove dead code and pointless local lut storage

The redundant fb helpers .load_lut, .gamma_set and .gamma_get are
no longer used. Remove the dead code and hook up the crtc .gamma_set
to use the crtc gamma_store directly instead of duplicating that
info locally.

Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170713162538.22788-7-peda@axentia.se

drm: armada: remove dead empty functions

The redundant fb helpers .gamma_set and .gamma_get are no longer used.
Remove the dead code.

Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170713162538.22788-6-peda@axentia.se

drm: amd: remove dead code and pointless local lut storage

The redundant fb helpers .load_lut, .gamma_set and .gamma_get are
no longer used. Remove the dead code and hook up the crtc .gamma_set
to use the crtc gamma_store directly instead of duplicating that
info locally.

Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170713162538.22788-5-peda@axentia.se

drm/rockchip: fix race with kms hotplug and fbdev

According to the kerneldoc[0], should do fbdev setup before calling
drm_kms_helper_poll_init(), otherwise, Kms hotplug event may race
into fbdev helper initial, and fb_helper->dev may be NULL pointer,
that would cause the bug:
[    0.735411] [00000200] *pgd=00000000f6ffe003, *pud=00000000f6ffe003, *pmd=0000000000000000
[    0.736156] Internal error: Oops: 96000005 [#1] PREEMPT SMP
[    0.736648] Modules linked in:
[    0.736930] CPU: 2 PID: 20 Comm: kworker/2:0 Not tainted 4.4.41 #20
[    0.737480] Hardware name: Rockchip RK3399 Board rev2 (BOX) (DT)
[    0.738020] Workqueue: events cdn_dp_pd_event_work
[    0.738447] task: ffffffc0f21f3100 ti: ffffffc0f2218000 task.ti: ffffffc0f2218000
[    0.739109] PC is at mutex_lock+0x14/0x44
[    0.739469] LR is at drm_fb_helper_hotplug_event+0x30/0x114
[    0.756253] [<ffffff8008a344f4>] mutex_lock+0x14/0x44
[    0.756260] [<ffffff8008445708>] drm_fb_helper_hotplug_event+0x30/0x114
[    0.756271] [<ffffff8008473c84>] rockchip_drm_output_poll_changed+0x18/0x20
[    0.756280] [<ffffff8008439fcc>] drm_kms_helper_hotplug_event+0x28/0x34
[    0.756286] [<ffffff800846c444>] cdn_dp_pd_event_work+0x394/0x3c4
[    0.756295] [<ffffff80080b2b38>] process_one_work+0x218/0x3e0
[    0.756302] [<ffffff80080b3538>] worker_thread+0x2e8/0x404
[    0.756308] [<ffffff80080b7e70>] kthread+0xe8/0xf0
[    0.756316] [<ffffff8008082690>] ret_from_fork+0x10/0x40

[0]: https://01.org/linuxgraphics/gfx-docs/drm/gpu/drm-kms-helpers.html

Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Sandy huang <sandy.huang@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1501575103-20136-1-git-send-email-mark.yao@rock-chips.com

drm/rockchip: vop: report error when check resource error

The user would be confused while facing a error commit without
any error report.

Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Sandy huang <sandy.huang@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1501494596-7090-1-git-send-email-mark.yao@rock-chips.com

drm/rockchip: vop: round_up pitches to word align

VOP pitch register is word align, need align to word.

VOP_WIN0_VIR:
  bit[31:16] win0_vir_stride_uv
    Number of words of Win0 uv Virtual width
  bit[15:0] win0_vir_width
    Number of words of Win0 yrgb Virtual width
    ARGB888 : win0_vir_width
    RGB888 : (win0_vir_width*3/4) + (win0_vir_width%3)
    RGB565 : ceil(win0_vir_width/2)
    YUV : ceil(win0_vir_width/4)

Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Sandy huang <sandy.huang@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1501494591-7034-1-git-send-email-mark.yao@rock-chips.com

drm/rockchip: vop: fix NV12 video display error

fixup the scale calculation formula on the case
src_height == (dst_height/2).

Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Sandy huang <sandy.huang@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1501494586-6984-1-git-send-email-mark.yao@rock-chips.com

drm/rockchip: vop: fix iommu page fault when resume

Iommu would get page fault with following path:
   vop_disable:
      1, disable all windows and set vop config done
      2, vop enter to standy, all windows not works, but their registers
         are not clean, when you read window's enable bit, may found the
         window is enable.

   vop_enable:
      1, memcpy(vop->regsbak, vop->regs, len)
         save current vop registers to vop->regsbak, then you can found
         window is enable on regsbak.
      2, VOP_WIN_SET(vop, win, gate, 1);
         force enable window gate, but gate and enable are on same
         hardware register, then window enable bit rewrite to vop hardware.
      3, vop power on, and vop might try to scan destroyed buffer,
         then iommu get page fault.

Move windows disable after vop regsbak restore, then vop regsbak mechanism
would keep tracing the modify, everything would be safe.

Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Sandy huang <sandy.huang@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1501494582-6934-1-git-send-email-mark.yao@rock-chips.com

drm/rockchip: vop: no need wait vblank on crtc enable

Since atomic framework, crtc enable and disable are in pairs,
no need to wait vblank.

Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Sandy huang <sandy.huang@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1501494577-6884-1-git-send-email-mark.yao@rock-chips.com

agp: nvidia: constify pci_device_id.

pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

agp: amd64: constify pci_device_id.

pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

agp: sis: constify pci_device_id.

pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

agp: efficeon: constify pci_device_id.

pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

agp: ati: constify pci_device_id.

pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

agp: ali: constify pci_device_id.

pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

agp: intel: constify pci_device_id.

pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

agp: amd-k7: constify pci_device_id.

pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

agp: uninorth: constify pci_device_id.

pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Merge branch 'topic-arcpgu-updates' of https://github.com/foss-for-synopsys-dwc-arc-processors/linux into drm-next

arcgpu minor updates.

* 'topic-arcpgu-updates' of https://github.com/foss-for-synopsys-dwc-arc-processors/linux:
  drm: arcpgu: Allow some clock deviation in crtc->mode_valid() callback
  drm: arcpgu: Fix module unload
  drm: arcpgu: Fix mmap() callback
  arcpgu: Simplify driver name
  drm/arcpgu: Opt in debugfs

Merge tag 'drm-next-du-20170803' of git://linuxtv.org/pinchartl/media into drm-next

rcar-du updates, contains vsp1 updates as well.

* tag 'drm-next-du-20170803' of git://linuxtv.org/pinchartl/media: (24 commits)
  drm: rcar-du: Use new iterator macros
  drm: rcar-du: Repair vblank for DRM page flips using the VSP
  drm: rcar-du: Fix race condition when disabling planes at CRTC stop
  drm: rcar-du: Wait for flip completion instead of vblank in commit tail
  drm: rcar-du: Use the VBK interrupt for vblank events
  drm: rcar-du: Add HDMI outputs to R8A7796 device description
  drm: rcar-du: Remove an unneeded NULL check
  drm: rcar-du: Setup planes before enabling CRTC to avoid flicker
  drm: rcar-du: Configure DPAD0 routing through last group on Gen3
  drm: rcar-du: Restrict DPLL duty cycle workaround to H3 ES1.x
  drm: rcar-du: Support multiple sources from the same VSP
  drm: rcar-du: Fix comments to comply with the kernel coding style
  drm: rcar-du: Use of_graph_get_remote_endpoint()
  v4l: vsp1: Add support for header display lists in continuous mode
  v4l: vsp1: Add support for multiple DRM pipelines
  v4l: vsp1: Add support for multiple LIF instances
  v4l: vsp1: Add support for new VSP2-BS, VSP2-DL and VSP2-D instances
  v4l: vsp1: Add support for the BRS entity
  v4l: vsp1: Add pipe index argument to the VSP-DU API
  v4l: vsp1: Don't create links for DRM pipeline
  ...

drm/fb-helper: add new drm_setup_crtcs_fb() function

This adds a new drm_setup_crtcs_fb() function to handle the parts of
drm_setup_crtcs() that touch fb_helper->fb and fb_helper->fbdev. When
drm_setup_crtcs() is called during initialization, these fields are NULL
because they have not been allocated yet.

There is currently a hack at the end of drm_fb_helper_single_fb_probe()
that sets fb_helper->fb, so it is moved to the new drm_setup_crtcs_fb()
function.

This is also done in preparation for addition setup that requires access
to fb_helper->fbdev.

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1501777149-8310-2-git-send-email-david@lechnology.com

drm/atmel-hlcdc: switch to drm_*{get,put} helpers

drm_*_reference() and drm_*_unreference() functions are just
compatibility alias for drm_*_get() and drm_*_put() and should not be
used by new code. So convert all users of compatibility functions to use
the new APIs.

Signed-off-by: Cihangir Akturk <cakturk@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1501761585-11757-6-git-send-email-cakturk@gmail.com

drm/atmel-hlcdc : constify drm_plane_helper_funcs and drm_plane_funcs.

drm_plane_helper_funcs and drm_plane_funcsare not supposed to change
at runtime. All functions working with drm_plane_helper_funcs and
drm_plane_funcs work with const. So mark the non-const structs as const.

File size before:
   text    data     bss     dec     hex filename
   6072     596       0    6668    1a0c atmel_hlcdc_plane.o

File size After adding 'const':
   text    data     bss     dec     hex filename
   6218     436       0    6654    19fe atmel_hlcdc_plane.o

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/646415a3b2e62182f85254115e8491e5caf4b2c7.1499098826.git.arvind.yadav.cs@gmail.com

drm: rcar-du: Use new iterator macros

for_each_obj_in_state is about to be removed, so use the correct new
iterator macros.

Also look at new_plane_state instead of plane->state when looking up
the hw planes in use. They should be the same except when reallocating,
(in which case this code is skipped) and we should really stop looking
at obj->state whenever possible.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

drm: rcar-du: Repair vblank for DRM page flips using the VSP

The driver recently switched from handling page flip completion in the
DU vertical blanking handler to the VSP frame end handler to fix a race
condition. This unfortunately resulted in incorrect timestamps in the
vertical blanking events sent to userspace as vertical blanking is now
handled after sending the event.

To fix this we must reverse the order of the two operations. The easiest
way is to handle vertical blanking in the VSP frame end handler before
sending the event. The VSP frame end interrupt occurs approximately 50µs
earlier than the DU frame end interrupt, but this should not cause any
undue harm.

As we need to handle vertical blanking even when page flip completion is
delayed, the VSP driver now needs to call the frame end completion
callback unconditionally, with a new argument to report whether page
flip has completed.

With this new scheme the DU vertical blanking interrupt isn't needed
anymore, so we can stop enabling it.

Fixes: d503a43ac06a ("drm: rcar-du: Register a completion callback with VSP1")
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

drm: rcar-du: Fix race condition when disabling planes at CRTC stop

When stopping the CRTC the driver must disable all planes and wait for
the change to take effect at the next vblank. Merely calling
drm_crtc_wait_one_vblank() is not enough, as the function doesn't
include any mechanism to handle the race with vblank interrupts.

Replace the drm_crtc_wait_one_vblank() call with a manual mechanism that
handles the vblank interrupt race.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

drm: rcar-du: Wait for flip completion instead of vblank in commit tail

Page flips can take more than one vertical blanking to complete if
arming the page flips races with the vertical blanking interrupt.
Waiting for one vblank to complete the atomic commit in the commit tail
handler is thus incorrect, and can lead to framebuffers being released
while still being scanned out.

Fix this by waiting for flip completion instead, using the
drm_atomic_helper_wait_for_flip_done() helper.

Fixes: 0d230422d256 ("drm: rcar-du: Register a completion callback with VSP1")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

drm: rcar-du: Use the VBK interrupt for vblank events

When implementing support for interlaced modes, the driver switched from
reporting vblank events on the vertical blanking (VBK) interrupt to the
frame end interrupt (FRM). This incorrectly divided the reported refresh
rate by two. Fix it by moving back to the VBK interrupt.

Fixes: 906eff7fcada ("drm: rcar-du: Implement support for interlaced modes")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

drm: rcar-du: Add HDMI outputs to R8A7796 device description

Update the device description with the HDMI output.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

drm: rcar-du: Remove an unneeded NULL check

"params" can't be NULL here.  The next lines assume that we either
hit the break statement of "params->mpixelclock == ~0UL".  The
inconsistent NULL checking makes static checkers complain.  I've just
removed the test.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

drm: rcar-du: Setup planes before enabling CRTC to avoid flicker

Commit 52055bafa1ff ("drm: rcar-du: Move plane commit code from CRTC
start to CRTC resume") changed the order of the plane commit and CRTC
enable operations to accommodate the runtime PM requirements. However,
this introduced corruption in the first displayed frame, as the CRTC is
now enabled without any plane configured. On Gen2 hardware the first
frame will be black and likely unnoticed, but on Gen3 hardware we end up
starting the display before the VSP compositor, which is more
noticeable.

To fix this, revert the order of the commit operations back, and handle
runtime PM requirements in the CRTC .atomic_begin() and .atomic_enable()
helper operation handlers.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

drm: rcar-du: Configure DPAD0 routing through last group on Gen3

On Gen3 SoCs DPAD0 routing is configured through the last CRTC group,
unlike on Gen2 where it is configured through the first CRTC group. Fix
the driver accordingly.

Fixes: 2427b3037710 ("drm: rcar-du: Add R8A7795 device support")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

drm: rcar-du: Restrict DPLL duty cycle workaround to H3 ES1.x

The H3 ES1.x exhibits dot clock duty cycle stability issues. We can work
around them by configuring the DPLL to twice the desired frequency,
coupled with a /2 post-divider. This isn't needed on other SoCs and
breaks HDMI output on M3-W for a currently unknown reason, so restrict
the workaround to H3 ES1.x.

From an implementation point of view, move work around handling outside
of the rcar_du_dpll_divider() function by requesting a x2 DPLL output
frequency explicitly. The existing post-divider calculation mechanism
will then take care of dividing the clock by two automatically.

While at it, print a more useful debugging message to ease debugging
clock rate issues.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

drm: rcar-du: Support multiple sources from the same VSP

On R-Car H3 ES2.0, DU channels 0 and 3 are served by two separate
pipelines from the same VSP. Support this in the DU driver.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

drm: rcar-du: Fix comments to comply with the kernel coding style

To avoid mixing comment styles when new comments complying with the
kernel coding style are introduced, fix all multiline comments in one
go.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

drm: rcar-du: Use of_graph_get_remote_endpoint()

Now, we can use of_graph_get_remote_endpoint(). Let's use it.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

v4l: vsp1: Add support for header display lists in continuous mode

The VSP supports both header and headerless display lists. The latter is
easier to use when the VSP feeds data directly to the DU in continuous
mode, and the driver thus uses headerless display lists for DU operation
and header display lists otherwise.

Headerless display lists are only available on WPF.0. This has never
been an issue so far, as only WPF.0 is connected to the DU. However, on
H3 ES2.0, the VSP-DL instance has both WPF.0 and WPF.1 connected to the
DU. We thus can't use headerless display lists unconditionally for DU
operation.

Implement support for continuous mode with header display lists, and use
it for DU operation on WPF outputs that don't support headerless mode.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

v4l: vsp1: Add support for multiple DRM pipelines

The R-Car H3 ES2.0 VSP-DL instance has two LIF entities and can drive
two display pipelines at the same time. Refactor the VSP DRM code to
support that by introducing a vsp_drm_pipeline object that models one
display pipeline.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

v4l: vsp1: Add support for multiple LIF instances

The VSP2-DL instance (present in the H3 ES2.0 and M3-N SoCs) has two LIF
instances. Adapt the driver infrastructure to support multiple LIFs.
Support for multiple display pipelines will be added separately.

The change to the entity routing table removes the ability to connect
the LIF output to the HGO or HGT histogram generators. This feature is
only available on Gen2 hardware, isn't supported by the rest of the
driver, and has no known use case, so this isn't an issue.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

v4l: vsp1: Add support for new VSP2-BS, VSP2-DL and VSP2-D instances

New Gen3 SoCs come with two new VSP2 variants names VSP2-BS and VSP2-DL,
as well as a new VSP2-D variant on V3M and V3H SoCs. Add new entries for
them in the VSP device info table.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

drm/fb: Fix pointer dereference before null check.

fb_crtc is used before a null check, so move the use after the null check.

This was just identified by inspection. I haven't actually observed a crash
here, so it is possible that the null check could be unnecessary.

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1501696813-8807-1-git-send-email-david@lechnology.com

drm: arcpgu: Allow some clock deviation in crtc->mode_valid() callback

Currently we expect that clock driver produces the exact same value
as we are requiring. There can, and will, be some deviation
however so we need to take that into account instead of just
rejecting the mode.

According to the HDMI spec we have a max of +-0.5% for the pixel clock
frequency deviation. Lets take that into an advantage and use it to
calculate how much deviation we can support.

Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Dave Airlie <airlied@gmail.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

drm: arcpgu: Fix module unload

At module unload we are expecting a struct drm_device but at
probing we are not setting it right. Fix this and correct the
arcpgu module unload.

Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Fixes: 0c4250e7b15e ("drm: Add support of ARC PGU display controller")
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Dave Airlie <airlied@gmail.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

drm: arcpgu: Fix mmap() callback

Now that ARC properly supports DMA mmap() we can use the standard
CMA helper to map dumb buffers. This makes ARC PGU works with
standard DRM consumer applications like, for example, mpv/mplayer
via DRM. While at it, use the DEFINE_DRM_GEM_CMA_FOPS() helper.

This fixes the use of dumb buffers.

Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Fixes: 0c4250e7b15e ("drm: Add support of ARC PGU display controller")
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Dave Airlie <airlied@gmail.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

arcpgu: Simplify driver name

This very minor change is still useful because it aligns
ARC PGU driver name with other DRM drivers and makes usage of
that driver name a bit easier.

For example in libdrm's test app we'll use "arcpgu" instead of
a bit more ugly "drm-arcpgu".

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/arcpgu: Opt in debugfs

This change adopts debugfs usage for outputting useful data.
As of today we print:
 * Mode and real HW clock values
 * Standard FB info

Code is heavily borrowed from ARM's HDLCD thus adding Liviu in Cc.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Jose Abreu <joabreu@synopsys.com>

Merge branch 'drm-next-4.14' of git://people.freedesktop.org/~agd5f/linux into drm-next

- Stop reprogramming the MC, the vbios already does this in asic_init
- Reduce internal gart to 256M (this does not affect the ttm GTT pool size)
- Initial support for huge pages
- Rework bo migration logic
- Lots of improvements for vega10
- Powerplay fixes
- Additional Raven enablement
- SR-IOV improvements
- Bug fixes
- Code cleanup

* 'drm-next-4.14' of git://people.freedesktop.org/~agd5f/linux: (138 commits)
  drm/amdgpu: fix header on gfx9 clear state
  drm/amdgpu: reduce the time of reading VBIOS
  drm/amdgpu/virtual_dce: Remove the rmmod error message
  drm/amdgpu/gmc9: disable legacy vga features in gmc init
  drm/amdgpu/gmc8: disable legacy vga features in gmc init
  drm/amdgpu/gmc7: disable legacy vga features in gmc init
  drm/amdgpu/gmc6: disable legacy vga features in gmc init (v2)
  drm/radeon: Set depth on low mem to 16 bpp instead of 8 bpp
  drm/amdgpu: fix the incorrect scratch reg number on gfx v6
  drm/amdgpu: fix the incorrect scratch reg number on gfx v7
  drm/amdgpu: fix the incorrect scratch reg number on gfx v8
  drm/amdgpu: fix the incorrect scratch reg number on gfx v9
  drm/amd/powerplay: add support for 3DP 4K@120Hz on vega10.
  drm/amdgpu: enable huge page handling in the VM v5
  drm/amdgpu: increase fragmentation size for Vega10 v2
  drm/amdgpu: ttm_bind only when user needs gpu_addr in bo pin
  drm/amdgpu: correct clock info for SRIOV
  drm/amdgpu/gmc8: SRIOV need to program fb location
  drm/amdgpu: disable firmware loading for psp v10
  drm/amdgpu:fix gfx fence allocate size
  ...

drm/ast: Actually load DP501 firmware when required

The ast driver has a code to load the DP501 firmware, but it's never
used.  This patch implements its actual usage by requesting the
firmware on demand, and release the firmware at exit as well.

Also the path contains a few cleanups and makes relevant functions
static.

Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/ast: Add an crtc_disable callback to the crtc helper funcs

Implement the proper CRTC disablement, just like done in mgag200
driver.

Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/ast: Fix memleak in error path in ast_bo_create()

The allocated struct ast_bo was not freed in all error paths.
This patch consolidates error handling and fixes this.

Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/ast: Free container instead of member in ast_user_framebuffer_destroy()

Technically freeing ast_fb->base is the same as freeing ast_fb as 'base'
the first member of the data structure.
Still this makes it cleaner.

Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/ast: Simplify function ast_bo_unpin()

Just a code refactoring, no functional change.

Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm: Create a format/modifier blob

Updated blob layout (Rob, Daniel, Kristian, xerpi)

v2:
* Removed __packed, and alignment (.+)
* Fix indent in drm_format_modifier fields (Liviu)
* Remove duplicated modifier > 64 check (Liviu)
* Change comment about modifier (Liviu)
* Remove arguments to blob creation, use plane instead (Liviu)
* Fix data types (Ben)
* Make the blob part of uapi (Daniel)

v3:
Remove unused ret field.
Change i, and j to unsigned int (Emil)

v4:
Use plane->modifier_count instead of recounting (Daniel)

v5:
Rename modifiers to modifiers_property (Ville)
Use sizeof(__u32) instead to reflect UAPI nature (Ville)
Make BUILD_BUG_ON for blob header size

Cc: Rob Clark <robdclark@gmail.com>
Cc: Kristian H. Kristensen <hoegsberg@gmail.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Daniel Stone <daniels@collabora.com> (v2)
Reviewed-by: Liviu Dudau <liviu@dudau.co.uk> (v2)
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com> (v3)
Signed-off-by: Daniel Stone <daniels@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170724034641.13369-2-ben@bwidawsk.net

drm: Plumb modifiers through plane init

This is the plumbing for supporting fb modifiers on planes. Modifiers
have already been introduced to some extent, but this series will extend
this to allow querying modifiers per plane. Based on this, the client to
enable optimal modifications for framebuffers.

This patch simply allows the DRM drivers to initialize their list of
supported modifiers upon initializing the plane.

v2: A minor addition from Daniel

v3:
* Updated commit message
* s/INVALID/DRM_FORMAT_MOD_INVALID (Liviu)
* Remove some excess newlines (Liviu)
* Update comment for > 64 modifiers (Liviu)

v4: Minor comment adjustments (Liviu)

v5: Some new platforms added due to rebase

v6: Add some missed plane inits (or maybe they're new - who knows at
this point) (Daniel)

Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Daniel Stone <daniels@collabora.com> (v2)
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Stone <daniels@collabora.com>

drm/msm: Convert to use new iterator macros, v2.

for_each_obj_in_state is about to be removed, so convert
to the new iterator macros.

Just like in omap, use crtc_state->active instead of
crtc_state->enable when waiting for completion.

Changes since v1:
- Fix compilation.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Rob Herring <robh@kernel.org>
Cc: Markus Elfring <elfring@users.sourceforge.net>
Cc: Sushmita Susheelendra <ssusheel@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170719143920.25685-6-maarten.lankhorst@linux.intel.com

drm/nouveau: Convert nouveau to use new iterator macros, v2.

Use the new atomic iterator macros, the old ones are about to be
removed. With the new macros, it's more easy to get old and new state so
get them from the macros instead of from obj->state.

Changes since v1:
- Don't mix up old and new state. (danvet)
- Rebase on top of interruptible swap_state changes.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20170719143920.25685-7-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/omapdrm: Fix omap_atomic_wait_for_completion

Use the new iterator macro and look for crtc_state->active instead of
enable, only crtc_state->active implies that vblanks will happen.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170719143920.25685-5-maarten.lankhorst@linux.intel.com