ASoC: Refactor symmetric_rates check to reduce indentation

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Convert WM9081 SYSCLK configuration to be device wide

Also respace the CODEC ops a bit for legibility.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Provide CODEC clocking operations and API calls

When multi component systems use DAIless amplifiers which require clocking
configuration it is at best hard to use the current clocking API as this
requires a DAI even though the device may not even have one. Address this
by adding set_sysclk() and set_pll() operations and APIs for CODECs.

In order to avoid issues with devices which could be used either with or
without DAIs make the DAI variants call through to their CODEC counterparts
if there is no DAI specific operation. Converting over entirely would create
problems for multi-DAI devices which offer per-DAI clocking setup.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Fix section mismatch warnings in WM8994

Annoying as the __devinitdata is actually correct.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Use data based init for WM9081 DAPM

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Add DAPM widget and path data to CODEC driver structure

Allow a slight simplification of CODEC drivers by allowing DAPM routes and
widgets to be provided in a table. They will be instantiated at the end of
CODEC probe.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Remove warnings in ep93xx-i2s.c

Remove warnings in ep93xx-i2s.c

Signed-off-by: Alexander Sverdlin <subaparts@yandex.ru>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Extend range of supported sample rates for CS4271 CODEC.

Extend range of supported sample rates for CS4271 CODEC.

Signed-off-by: Alexander Sverdlin <subaparts@yandex.ru>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add LM4857 to SND_SOC_ALL_CODECS

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Add driver for the dfbmcs320 bluetooth module

This patch adds a codec driver for the dfbmcs320 bluetooth module, which is used
on the neo1973 boards.

The patch also modifies the neo1937_wm8753 sound board driver to use the new
driver instead of registering the bluetooth DAI manually.
Previously there was a name mismatch between the bluetooth DAI and the bluetooth
DAI link and the sound card was not instantiated, with this patch the issue is
no longer present and sound support works again.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Samsung: Merge neo1937_wm8753 and neo1973_gta02_wm8753 sound board driver

The neo1973(GTA01) and neo1973_gta02(GTA02) have a very similar audio hardware
setup. They both use the same codec with the same routing to the gsm modem and
bluetooth chip. But they do use different AMPs though and there are some minor
differences in the speaker setup.

As a result most of the code of those two drivers is identical.
So from a maintenance point of view it makes sense to merge them into a single
driver. It also reduces the size of kernel images supporting both the GTA01 and
GTA02.

As a side-effect of this merge the GTA01 for example gains support for routing
audio to and from the bluetooth DAI.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: neo1973_gta02_wm8753: Use gpio_request_array to request gpios

Using gpio_request_array instead of requesting and setting up each gpio by hand
makes the code more readable and more compact.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: neo1973_gta02_wm8753: Remove lm4853_{set,get}_state

This patch drops the lm4853_{set,get}_state functions and the "Amp State Switch"
control.
Those were noops which existed to maintain alsa state file compatibility. Since
the control names have changed due to internal changes in the ASoC core and
state file compatibility was broken anyway it makes sense to drop them.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: neo1973_wm8753: Move lm4857 specefic code to its own module

This patch moves the code for the lm4857 AMP from the neo1973_wm8753 sound
board driver to its own module.
The lm4857 is a generic AMP IC and not specific to the neo1973.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: neo1973_wm8753: Remove scenario management code.

It has been proven to be inflexible to do scenario management in kernel space.

Since actual neo1973 board support has not been merged in mainline and this
patch has been in the neo1973 tree for some time now it should be safe to remove
this functionality without breaking existing userspace.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add machine driver for Visstrim_M10 board.

Visstrim_M10 boards have an external tlcv320aic3205 codec
attached to SSI1. This driver glues together both interfaces.
External amplifier is not supported in this first version.

Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Constify i2c_device_id table

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Alexander Sverdlin <subaparts@yandex.ru>
Acked-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: tlv320dac33: add MODULE_DEVICE_TABLE

The device table is required to load modules based on modaliases.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add missing debugfs conditionals

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Fix outdated API usage in tlv320aic32x4

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Add TI tlv320aic32x4 codec support.

This patch adds support for tlv320aic3205 and tlv320aic3254 codecs.
It doesn't include miniDSP support for aic3254.

Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add a late_probe() callback to cards

This is run after the DAPM widgets and routes are added, allowing setup
of things like jacks using the routes. The main card probe() is run before
anything else so can't be used for this purpose.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Allow card DAPM widgets and routes to be set up at registration

These will be added after all devices are registered and allow most DAI
init functions in machine drivers to be replaced by simple data.
Regular controls are not supported as the registration function still
works in terms of CODECs.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Add a per-card DAPM context

This means that rather than adding the board specific DAPM widgets to a
random CODEC DAPM context they can be added to the card itself which is
a bit cleaner. Previously there only was one DAPM context and it was
tied to the single supported CODEC.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Check for a CODEC before dereferencing in DAPM

A CODEC pointer is optional (and is checked for in most contexts within
DAPM) - add checks to the few places where it was missed.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Get the card directly from the DAPM context

Rather than indirecting through the CODEC we can look the card up directly
from the card pointer in the DAPM context.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Add TLV information for WM8978 DAC limiter

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

Merge branch 'for-2.6.38' into for-2.6.39

ASoC: Fix broken bitfield definitions in WM8978

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org

ASoC: WM8994: Ensure MICBIAS is provided with a clock

The patch 'ASoC: WM8994: Improve Playback Robustness' did not handle
this case properly.

Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add platform data for WM9081 IRQ pin configuration

The WM9081 IRQ output can be either active high or active low and can
support either CMOS or open drain modes.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Remove module probe announcements from CODEC drivers

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Fix burstsize and DSP_B format problems in imx-ssi.

When choosing IMX_DMA flag, burtsizes are set to its default
value (0) which leads to driver malfunction. Change them to 4.

DSP_B interface needs additional flag to match DSP_B formats
as described in several codecs as wm8741 and aic3205.

Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: WM8994: Ensure MICBIAS is provided with a clock

The patch 'ASoC: WM8994: Improve Playback Robustness' did not handle
this case properly.

Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-2.6.38' into for-2.6.39

ASoC: WM8994: Ensure late enable events are processed for the ADCs

Ensure that the ADCs are provided with a clock as the previous patch
"ASoC: WM8994: Improve playback robustness" did not handle this case
properly.

Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

ASoC: WM8994: Don't disable the AIF[1|2]CLK_ENA unconditionaly

Since we began using the late clock disable functionality, ensure that
we don't disable the clock if any of the ADC or DAC paths are still
enabled.  This happens when we have simultaneous playback and recording.

Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

ASoC: Fix WM9081 platform data initialisation

It went AWOL in the multi-component conversion.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org

ASoC: Tegra: Fix error handling in DMA channel alloc

tegra_dma_allocate_channel() returns NULL on errors, not an error pointer.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Staticise non-exported symbols in SGTL5000

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: remove unnecessary header including in SGTL5000 codec driver

Remove unnecessary headers:
 - mach/hardware.h in sgtl5000.c
 - linux/i2c.h in sgtl5000.h

Signed-off-by: Zeng Zhaoming <b32542@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-2.6.38' into for-2.6.39

ASoC: eukrea-tlv320: add MBIMXSD51 support

Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Liam Girdwood <lrg@slimogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Move WM2000 to dev_pm_ops

There's a general move to use dev_pm_ops rather than bus specific functions
in order to facilitate work on the PM core. Do this conversion to WM2000.
The driver ought to be updated to work better in a multi-component model
but the mechanical conversion ensures that we avoid blocking PM core work
until that happens.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

eukrea-tlv320: fix platform_name

commit f0fba2ad1b6b53d5360125c41953b7afcd6deff0 included a mistake
on the name of the platform in the snd_soc_dai_link structure.

Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

ASoC: Add Freescale SGTL5000 codec support

Add Freescale SGTL5000 codec support.
Supported features:
 - line-in and mic input
 - headphone and line-out output
 - line-in bypass ADC and DAC to headphone
 - 16, 20, 24, 32 bit audio
 - 8 ~ 96k sample rates

Signed-off-by: Zeng Zhaoming <zhaoming.zeng@freescale.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: remove one to many l's in the word

The patch below removes an extra "l" in the word.

Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-2.6.38' into for-2.6.39

ASoC: Tegra: Move utilities to separate module

The utilities will be required by every machine driver. Including the
utility object directly into every machine driver causes a build failure
if the modules are actually built into the kernel, since each will define
the symbols exported by the utility file. Solve this by moving the
utility object into a separate module.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: soc-dapm: Include quotes around contents in debugfs entries

Sometimes the name of the control switch of a dapm route contains
spaces which makes it impossible to distinguish it from the source widget.
Add quotes around the names of the widgets to makes these parsable.

Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Remove -codec suffix from WM9081 driver

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: correct pxa AC97 DAI names

Correct names for pxa AC97 DAI are pxa2xx-ac97 and pxa2xx-ac97-aux. Fix
that for all PXA platforms.

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

ASoC: Pass the jack to jack notifiers

We're currently not passing anything and this will make the card and so on
more discoverable.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Simplify default WM8958 jack detection code

The default WM8958 jack detection handler implements a full set of buttons
and also support for video detection. Support for multi-button jacks is
fairly system specific and will usually require some tuning for headsets
so simplify the implementation to only report a simple short to ground
button, leaving multi-button headsets to be handled by system specific
code.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Support configuration of WM8958 microphone bias analogue parameters

The WM8958 has a different microphone bias architecture to WM8994 so needs
different configuration to WM8994. Support this in platform data.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Support WM8958 direct microphone detection IRQ

Allow direct routing of the WM8958 microphone detection signal to a GPIO
to be used, saving the need to demux the interrupt.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Mark WM8958 microphone bias registers as readable

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Run bias level changes for all DAPM contexts in parallel

As bias level changes can be quite time consuming and the bias changes
for multiple devices aren't strongly tied to each other (if anything it
can be advantageous to bring different devices up together) we can improve
the state transition time for multi-component systems by running the bias
level changes for all the devices in parallel. This is very simple to
achieve using the kernel async functionality so use that to schedule the
work.

This should have no practical effect for the overwhelming majority of
systems which have a single DAPM context - we'll bounce into another
thread to do the bias level change but otherwise everything will happen
in exactly the same order as it did before.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Remove card from snd_soc_dapm_set_bias_level()

We can get the card from the DAPM context so don't bother passing it as
an argument.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

Merge branch 'for-2.6.38' into for-2.6.39

ASoC: Hook wm_hubs micbiases up to CLK_SYS

The microphone detection functionality requires a clock to work. In any
non-detection case where the MICBIAS is enabled CLK_SYS will be needed
anyway so there is no negative impact on power consumption.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Correct definition of WM8903_VMID_RES_5K

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Fix WM8958 default microphone detection argument ordering

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Hook wm_hubs micbiases up to CLK_SYS

The microphone detection functionality requires a clock to work. In any
non-detection case where the MICBIAS is enabled CLK_SYS will be needed
anyway so there is no negative impact on power consumption.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Mark WM8958 microphone detection registers readable

So they show up in codec_reg.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add kerneldoc for jack_status_check callback

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Allow GPIO jack detection to be configured as a wake source

Some systems wish to use jacks as wake sources. Provide a wake flag in the
GPIO configuration which causes the driver to enable the IRQ as a wake
source.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Log wm_hubs DC servo operation code when reporting a timeout

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Remove export of snd_soc_dapm_stream_event()

The only thing that should ever be calling this is soc-core and that is
built as part of the same module so doesn't need the export.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Fix missing space in WM8994

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: sst_platform: fix the pulseaudio error

Pulseaudio doesnt work with current driver and it was root caused to absense of
hw_params function and malloc_pages in it.
This patch adds this and allows pa to work fine with these drivers

Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: mfld_machine: make use of soc_register_card API

This patch removes the old method of soc-audio device creation in mfld machine
and makes use of new soc_register_card API to register the card

Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: sn95031: fix the amic tlv scale

The tlv scale is defined as (min, step, mute). The mute is not supported here so
put the value to 0

Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: sn95031: fix the DMIC path routing

This patch makes the DMIC dynamically connect to TX Mux, earlier code had
erroneously made this as static path

Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: sn95031: make playback rails depend on actual pins they control

This patch makes the codec playback rails (headset and speaker) depend on
actual pins they control. This enables better power management of the codec

Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-2.6.38' into for-2.6.39

ASoC: Warn if WM8903 platform data is used to enable microphone IRQ

The WM8903 interrupts are clear on read so if the WM8903 detection is
enabled from platform data when the IRQ is in use (rather than using a
direct signal from a GPIO) status may be lost during startup. Help users
spot this misconfiguration by adding a WARN_ON().

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Tegra: Add MODULE_ALIAS

With the appropriate MODULE_ALIAS in place, the audio modules will be
automatically loaded; there is no longer a need for manual modprobes.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Tegra: Harmony: Explicitly set mic enables

Harmony has both an external mic (a regular mic jack) and an internal mic
(a 0.1" two-pin header on the board).

The external mic is connected to the WM8903's IN1L pin, and is supported
by the current driver.

The internal mic is connected to the WM8903's IN1R pin, and is not supported
by the current driver.

It appears that no Harmony systems were shipped with any internal mic
connected; users were expected to provide their own. This makes the
internal mic connection less interesting.

The WM8903's Mic Bias signal is used for both of these mics. For each mic,
a GPIO drives a transistor which gates whether the mic bias signal is
actively connected to that mic, or isolated from it.

The dual use of the mic bias for both mics makes a general-purpose complete
implementation of mic detection using the mic bias complex. So, for
simplicity, the internal mic is currently ignored by the driver.

This patch configures the relevant GPIOs to enable the mic bias connection
to the external mic, and disable the mic bias connection to the internal
mic. Note that in practice, this is the default state if these GPIOs aren't
configured.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Harmony: Call snd_soc_dapm_nc_pin

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Tegra: Harmony: Implement mic detection

* Add jack definition for mic jack
* Request wm8903 to enable mic detection
* Force mic bias on, since it's required for mic detection

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Ensure supplies are maintained for force enabled widgets

If a widget has been force enabled then not only do we need to keep the
widget itself enabled, we also need to keep any supplies the widget
requires enabled. The user could force all the individual widgets on but
this requires too much knowledge of device internals.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: WM8994: Improve playback robustness

On WM8994 revision D and earlier ensure proper playback robustness
as some rare use cases can trigger issues.

Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

ASoC: WM8994: Improve robustness in some use cases

Ensure that on disabling certain registers such as AIF1DAC1L,
AIF1DAC1R etc. the AIF1CLK and AIF2CLK remain enabled.  Similarly
when enabling those registers, AIF1CLK and AIF2CLK will remain
disabled.

Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

ASoC: WM8903: Fix mic detection enable logic

The mic detection HW should be enabled when either mic or short detection
is required, not when only both are required.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

ASoC: WM8903: Fix mic detection register definitions

* There is no hysteresis enable field in the current datasheet.
* Mic detection threshold field is only 2 bits wide.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Allow use sleeping gpio in soc-jack

It is safe to use sleeping gpio in snd_soc_jack_gpio_detect as it is not
called from interrupt context. This avoids WARN_ON from __gpio_get_value
if sleeping gpio is registered for jack.

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: mid-x86: Use the soc-jack apis for jack type detection

This patch modifies the mfld_machine to use the new jack apis for adding the
voltage zones for jack type detection. It also modifed TI sn95031 codec driver
to use these new apis

Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-2.6.38' into for-2.6.39

ASoC: Use explicit sequence for WM8903 bias off

This makes no real difference compared to the write sequencer sequence
that was previously used but can run without a clock being provided.
Also remove the write sequencer support code as this was the last use
of it.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Don't use write sequencer to power up WM8903

The write sequencer sequencer sequence takes longer than is desirable
as it brings up a full playback path which is not required at this
point. Open coding the sequence cuts the startup time by two thirds.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Convert WM8903 bias management to use snd_soc_update_bits()

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: CX20442: fix wrong reg_cache_default content

Content of the CX20442's snd_soc_codec_driver.reg_cache_default pointed
area, introduced with my recent NULL pointer dereferece fix (commit
f019ee5feb344ff0b22b58df4568676295aae14f), occured wrong after further
testing, more thorough than just booting successfully. There are two
problems with it:

1) It should read
(1 << CX20442_TELOUT) | (1 << CX20442_MIC),
   not
CX20442_TELOUT | CX20442_MIC.

2) While correctly matching actual codec hardware state on boot when
   fixed per 1), a few more code modifications would still be required
   to reflect that state not only into register cache, but also force
   them into DAPM pins state, otherwise an inconsitency occures which
   may prevent further codec state changes from being applied correctly.
   As a result, the phone stops ringing after reboot, until someone
   picks up the handset for the first time.

Revert that reg_cache_default content to a working, previous de facto
default value of 0, in hope this change can still be accepted as an rc
cycle fix.

Created and tested against linux-2.6.38-rc4

Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Actively manage WM8903 DC servo configuration

Explicitly cache the DC servo offsets for digital paths in the driver,
allowing them to be preserved over suspend and resume, and ensure that
we recalibrate analogue outputs paths when they are in use so that we
cover any changes in the input offset.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: add support for multiple jack types

This patch adds soc-jack support for adding voltage zones and for
detecting jack type

Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-2.6.38' into for-2.6.39

ASoC: Sync initial widget state with hardware

ASoC generally uses the register defaults for everything, but in some
cases the hardware will default to enabling some of the DAPM widgets
(clocks for example). Ensure that DAPM knows about the actual widget
state at initialisation by reading the enable bits after instantiating
the widgets so they don't get left enabled needlessly.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Fix WM8903 DAC mute default

The WM8903 register map does not mute the DAC by default at startup
so we need to explicitly do so.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Dynamically manage CLK_SYS in WM8903

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Convert WM8903 to use PGA_S for output stage enables

This simplfies the code and slightly reduces the startup time.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>