p54: enhance firmware parser to reduce memory waste

This patch greatly reduces one of biggest memory waste in the driver.

The firmware headers provides the right values for extra head-/tailroom
and mtu size which are usually much lower than the old hardcoded ones.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54pci: increase ring buffer index counter when skipping

I'm afraid, I forgot to add the following lines to
7262d59366 ("p54pci: rx tasklet refactoring").

These changes are necessary to ensure loop termination.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

toshiba_acpi: Add support for bluetooth toggling through rfkill (v8)

There's been a patch floating around for toshiba_acpi that exports an ad-hoc
/proc interface to toggle the bluetooth adapter in a large number of Toshiba
laptops. I'm not sure if it's still relevant for the latest models, but it is
still required for older models such as my Tecra M3.

This change pulls in the low level Toshiba-specific code from the old patch and
sets up an rfkill device and a polled input device to track the state of the
hardware kill-switch.

Signed-off-by: Philip Langdale <philipl@overt.org>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Add LP-PHY radio register definitions

This adds definitions for the LP-PHY radios.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Add LP-PHY read/write phyops

This adds read/write phyops for the LP-PHY and LP-PHY radios.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Add LP-PHY template

This adds template code for the LP-PHY.
No actual functionality is implemented.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Move code from nphy.* to phy_n.*

Sourcecode files for PHY code are named by phy_XXX.{c,h}
where XXX is the PHY type.
Move the N-PHY code to match the other files.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Move remaining code from phy.c to phy_a.c

This moves the remaining code from phy.c to phy_a.c
phy.c is removed.
No functional change. Just moving code and removing dead code.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: keep track of supported interface modes

It is obviously good for userspace to know up front which
interface modes a given piece of hardware might support (even
if adding such an interface might fail later because of
concurrency issues), so let's make cfg80211 aware of that.
For good measure, disallow adding interfaces in all other
modes so drivers don't forget to announce support for one mode
when they add it.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: HW code cleanup

 * No code changes...

 * Split hw.c to multiple files for better maintenance and add some documentation on each file
   code is going to grow soon (eeprom.c for example is going to get much stuff currently developed
   on ath_info) so it's better this way.

 * Rename following functions to maintain naming scheme:

     ah_setup_xtx_desc -> ah_setup_mrr_tx_desc
     (Because xtx doesn't say much, it's actually
     a multi-rate-retry tx descriptor)

     ath5k_hw_put_tx/rx_buf - > ath5k_hw_set_tx/rxdp
     ath5k_hw_get_tx/rx_buf -> ath5k_hw_get_tx/rxdp
     (We don't put any "buf" we set descriptor pointers on hw)

     ath5k_hw_tx_start -> ath5k_hw_start_tx_dma
     ath5k_hw_start_rx -> ath5k_hw_start_rx_dma
     ath5k_hw_stop_pcu_recv -> ath5k_hw_stop_rx_pcu
     (It's easier this way to identify them, we also
     have ath5k_hw_start_rx_pcu which completes the
     set)

     ath5k_hw_set_intr -> ath5k_hw_set_imr
     (As in get_isr we set imr here, not "intr")

  * Move ath5k_hw_setup_rx_desc on ah->ah_setup_rx_desc so we can
    include support for different rx descriptors in the future

  * Further cleanups so that checkpatch doesn't complain
    (only some > 80 col warnings for eeprom.h and reg.h as usual
    due to comments)

  Tested on 5211 and 5213 cards and works ok.

Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Don't use memcpy for overlapping areas

It is valid to pass &gphy->rfatt and &gphy->bbatt as rfatt and bbatt
pointer arguments to the function. So we have to use memmove for the
possibly overlapping memory areas.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

s2io: reindented misleading for loop

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

[netdrvr] removed unused #include <version.h>

The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
  drivers/net/myri10ge/myri10ge.c
  drivers/net/netxen/netxen_nic_ethtool.c
  drivers/net/tokenring/lanstreamer.c

This patch removes the said #include <version.h>.

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

8139too: use netdev_alloc_skb

This patch uses netdev_alloc_skb. This sets skb->dev and allows
arch specific allocation. Also cleanup the alignment code.

Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

8139cp: use netdev_alloc_skb

This patch uses netdev_alloc_skb. This sets skb->dev and allows
arch specific allocation. Also cleanup the alignment code.

Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

via-rhine: changed to use netdev_alloc_skb() from dev_alloc_skb

Use netdev_alloc_skb. This sets skb->dev and allows
arch specific allocation. Also cleanup the alignment code.

Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sky2: display product info on boot.

Change bootup messages to print more information. This is to help users
who may have old buggy EEPROM image.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sky2: EEPROM read/write bug fixes

Cleanup and harden the routines accessing the EEPROM.
  1. Prevent spin forever waiting for the TWSI bus
  2. Fix write eeprom to write full words rather than only 16 bits
    Luckly the vendor doesn't provide EEPROM in Linux format so it must never
    have been used.
  3. Don't allow partial eeprom writes, not needed, not safe.

These are non-urgent bug fixes.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Merge branch 'r8169-fixes' of git://git./linux/kernel/git/romieu/netdev-2.6 into upstream-next

ixgbe: change config srrctl to only program one register per VMDq/RSS id

This change makes it so only one srrctl register is programmed per VMDq id, and if VMDq is not enabled it is one register per RSS queue.  Currently this function is working correctly for the multiqueue RSS and single queue cases, but if any advances features such as VMDq or DCB would have been enabled this function would have caused issues as it was not correct.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

igb: clean up a stray fake netdev code left in rx path

Remove code that was in place to support fake netdev

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

igb: remove unneeded cleaned variable in clean_tx_irq path

The cleaned variable can be replaced by the count of packets cleaned during
the tx interrupt routine so it can be removed.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

e1000e: add support for new 82574L part

This new part has the same feature set as previous parts with the addition
of MSI-X support.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

e1000e: add support for 82567LM-3 and 82567LF-3 (ICH10D) parts

Add support for new LOM devices on the latest generation ICHx platforms.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

e1000e: add support for the 82567LM-4 device

Enable PCI device ID for a new combination of MAC and PHY already supported
in the driver.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: use different context for tso and offload

Change TSO offloads to use a different context than VLAN insertion
and Tx checksumming.  Hardware has separate registers internally for
storing these so use them.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: fix dca hints going to wrong processor

hardware was configured incorrectly which led all hints to be
sent to queue[0]'s DCA configuration.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: fix bug where lro settings are per ring

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: update dca to new interface, fix CONFIG_DCA_MODULE

DCA related fixes
=================
- ixgbe was not compiling and using DCA correctly if dca was a module
- DCA interface changed with new kernel
- ixgbe was not correctly configured to indicate DCA hints to the
  correct CPU.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: should not use HW_CSUM, should use IP* flags

as mentioned by Herbert, our hardware supports IP offloads, not full
checksum offloads for any protocol in existence (even though the
hardware just provides generic csum support over any range of bytes)

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: Lock RSS seed, move rx_buf_len to the rx_ring

This locks the seed down so loading/unloading the driver will present
predictable hashing from RSS.  Also move the rx_buf_len out of the adapter
struct, and into the Rx ring struct.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: Implement Tx Head Writeback

Enable Tx Head Writeback in the hardware.  This helps performance by
removing adapter writebacks to descriptors on transmit completion.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: disable flow control by default

Since the adapter cannot tell what the remote end's flow control capability
is through auto-neg, we must turn off flow control by default.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: Cleanup references to Tx and Rx rings to becommon across the driver

Cleanup all the different references to the Tx ring and Rx ring structures
and make them common across the driver.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: do not update stats twice each receive

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: Implement HAVE_SET_RX_MODE

Implement HAVE_SET_RX_MODE in the driver for MC and UC lists.

Signed-off-by: Christopher Leech <christopher.leech@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: add little endian annotations for sparse

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: fix rx csum return status misinterpretation

the driver was misinterpreting rx_csum return value in the descriptor
so occassionally we would indicate an rx_csum error in our stats
when there was none.  This would have no effect on traffic because
we would just hand the packet to the stack anyway without the offload
flag set, but would increase CPU for those packets that needed a recompute.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ibm_newemac: MAL[12]_IER_EVENTS definition: 2x *_OTE -> *_DE

MAL[12]_IER_EVENTS definitions have MAL_IER_OTE twice
but lack MAL_IER_DE

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

hp-plus: fix link objects

Fix hp-plus Makefile object file:

drivers/built-in.o: In function `hpp_open':
hp-plus.c:(.text+0xaf445): undefined reference to `ei_interrupt'
hp-plus.c:(.text+0xaf4ac): undefined reference to `ei_open'
drivers/built-in.o: In function `hpp_close':
hp-plus.c:(.text+0xaf59d): undefined reference to `ei_close'
drivers/built-in.o: In function `hpp_probe1':
hp-plus.c:(.init.text+0x7314): undefined reference to `ei_poll'
drivers/built-in.o: In function `hp_plus_probe':
(.init.text+0x7407): undefined reference to `__alloc_ei_netdev'
make[1]: *** [.tmp_vmlinux1] Error 1

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

bonding: change some __constant_htons() to htons()

Resending since I didn't see any responses from the first try.

Change __constant_htons() to htons() in the bonding driver, it should
only be used for initializers.

-Brian

Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Rework efx_set_multicast_hash()

When !port_enabled, defer the write to reconfigure_mac_wrapper.

Whilst here, simplify the logic now that efx_start_port() always calls
efx_reconfigure_port().

From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Remove the STATE_RESETTING flag

This was originally a kludge to fix broken locking, which has since
been fixed properly.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Extend self-tests

Include PMA/PMD in loopback self-tests as intended.

Add NVRAM checksum validation and include it in self-tests.

Add register self-tests.

Run PHY self-tests where available.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Rework the bitfield header so that we can identify fields by bit number

This will support register self-tests.

From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Cleanup reset code

Move more code from efx_reset() into efx_reset_down() and efx_reset_up().

Stop propagating MAC/PHY setting failures from efx_reset_down() and
efx_reset_up() as these should not be fatal.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Remove some unreachable error paths

Some functions return an error code which is always 0.  Change their
return types to void and simplify their callers accordingly.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Remove remnants of multi-port abstraction for MAC registers

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Remove efx_nic_dummy_op_int() as redundant with efx_port_dummy_op_int()

Update comment on the dummy operation implementations.

Line up the board operation initialisers.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Enable TSO for 802.1q VLAN devices

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Do not call netif_{stop,wake}_queue() before register_netdev

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Make PHY flash mode a device attribute, not a module parameter

This allows updating PHY firmware for one interface without removing
all other interfaces handled by the driver.

Replace tx_disabled flags and 10Xpress status enumeration with flags in
enum efx_phy_mode.

Prevent an interface from being brought up while in PHY flash mode.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Implement get_sset_count, replacing get_stats_count and self_test_count

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Cleanup RX event processing

Make efx_process_channel() and falcon_process_eventq() return the
number of packets received rather than updating the quota, consistent
with new NAPI.

Since channels and RX queues are mapped one-to-one, remove return
value from falcon_handle_rx_event() and add a warning for events
with the wrong RX queue number.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Remove efx_channel::evqnum field

It is redundant with efx_channel::channel.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Make efx_for_each_channel_rx_queue() more efficient

Currently each channel can have at most one RX queue, so go straight to
that one.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Remove initialisation of RX_FILTER_CTL_REG.NUM_KER

We have long since given up doing RSS on Falcon A1 and therefore we
would always write the default value of 0.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Cleanup RX queue information

Rename efx_nic::rss_queues to the more obvious n_rx_queues

Remove efx_rx_queue::used and other stuff that's redundant with it.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Remove efx_channel::has_interrupt

efx_channel::has_interrupt is redundant with efx_channel::used_flags.

Remove efx_test_eventq() because it is now obviously unreachable.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Move CPU counting for RSS into a separate function, efx_wanted_rx_queues()

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Export boot configuration in EEPROM through ethtool

Extend the SPI device setup code to support this.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Removed forced inlining of long functions

gcc will automatically inline static functions with only one caller, and
may inline other functions depending on the kernel configuration and size
of the intermediate code.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Cleaned up struct tso_state fields

Squashed nested structures.

Renamed remaining_len to out_len, ifc.len to in_len, header_length to
header_len.

Moved ipv4_id into the group of output variables where it belongs.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Set net_device::vlan_features appropriately

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Use explicit bool for boolean variables, parameters and return values

Replace (cond ? 1 : 0) with cond or !!cond as appropriate, and
(cond ? 0 : 1) with !cond.

Remove some redundant boolean temporaries.

Rename one field that looks like a flag but isn't.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Reduce the size of struct efx_tx_buffer

Remove unmap_addr since it can be calculated from dma_addr, len and
unmap_len.  This saves 4-16 bytes.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Use pci_map_single() to map the skb header when doing TSO

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Don't leak PCI DMA maps in the TSO code when the queue fills up

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Speed up loopback self-test

Add efx_poll_loopback() function to test for successful completion of test.
Change efx_test_loopback() to end the test after 1 ms if
efx_poll_loopback() indicates success, and otherwise to wait for 100 ms
as before.

While we're here, rename efx_{rx,tx}_loopback() to
efx_{begin,end}_loopback() which more accurately reflect their
purpose.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Self-test reporting cleanup

Removed log messages that are redundant with calling functions.
Fixed bitwise or-ing of return codes.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Reduce log level for XGXS lane status

This was making noise during 10Xpress self-test.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Reverse the XOFF/XON pause frame control fifo thresholds

These were clearly bogus.

From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Remove inclusion of workarounds.h from efx.c

efx.c does not use hardware workarounds.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: XMAC statistics fix-ups

Exclude assumed size of RX control frames from rx_bad_bytes.

Exclude assumed size of TX control frames from tx_good_bytes for
consistency with rx_good_bytes.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Remove mistaken hardware workaround

We believed that some valid SNAP frames were being marked as invalid.
In fact this is not the case and no workaround is needed.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Reduce delays in SFE4001 initialisation

Currently the board initialisation includes 2 delays of 1 second each.
Usually it is unnecessary to wait that long, so check before doing so.

Correct some of the comments and log messages while we're here.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Avoid mangling error codes in efx_test_loopback()

efx_test_loopback() used "|" to combine the results of the RX and TX
phases.  If both phases fail with different error codes, this results
in a bogus error code.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Use separate hardware TX queues to select checksum generation

Checksum generation is an attribute of our hardware TX queues, not TX
descriptors.  We previously used a single queue and turned checksum
generation on or off as requested through ethtool.  However, this can
result in regenerating checksums in raw packets that should not be
modified.  We now create 2 hardware TX queues with checksum generation
on or off.  They are presented to the net core as one queue since it
does not know how to select between them.

The self-test verifies that a bad checksum is unaltered on the queue
with checksum generation off.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Remove unused field efx_channel::reset_work

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Change first parameter type of {set,clear}_bit_le() to unsigned

This means the compiler doesn't need to use real division instructions.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Replace net_dev->priv with netdev_priv(net_dev)

Use of the net_device::priv field is deprecated.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

netlink: Remove compat API for nested attributes

Removes all _nested_compat() functions from the API. The prio qdisc
no longer requires them and netem has its own format anyway. Their
existance is only confusing.

Resend: Also remove the wrapper macro.

Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of /linux/kernel/git/davem/net-2.6

Conflicts:

net/mac80211/mlme.c

net: Unbreak userspace usage of linux/mroute.h

Nothing in linux/pim.h should be exported to userspace.

This should fix the XORP build failure reported by
Jose Calhariz, the debain package maintainer.

Nothing originally in linux/mroute.h was exported to userspace
ever, but some of this stuff started to be when it was moved into
this new linux/pim.h, and that was wrong.  If we didn't provide these
definitions for 10 years we can reasonably expect that applications
defined this stuff locally or used GLIBC headers providing the
protocol definitions.  And as such the only result of this can
be conflict and userland build breakage.

Signed-off-by: David S. Miller <davem@davemloft.net>

pkt_sched: Fix locking of qdisc_root with qdisc_root_sleeping_lock()

Use qdisc_root_sleeping_lock() instead of qdisc_root_lock() where
appropriate. The only difference is while dev is deactivated, when
currently we can use a sleeping qdisc with the lock of noop_qdisc.
This shouldn't be dangerous since after deactivation root lock could
be used only by gen_estimator code, but looks wrong anyway.

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: When we droped a packet, we should return NET_RX_DROP instead of 0

Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next-2.6

b43: Rewrite TX power adjustment

This patch rewrites the TX power recalculation algorithms to scale better
with changed enviromnent. If there's low
TX traffic, the power will be checked against the desired values
every 60 seconds.
If there is high TX traffic, the check is redone every 2 seconds. This improves
the reaction times a lot and confuses the rate control less.
It will also reduce the time it initially takes to tune to a new TX power
value. With the old algorithm it could take about 30 to 45 seconds to settle to
a new power value. This will happen in about two to four seconds now.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Implement dynamic PHY API

This patch implements a dynamic "ops" based PHY API.
This is needed in order to conveniently support future PHY types
to avoid the "switch"-hell.

This patch does not change any functionality. It just moves lots
of code from one place to another and adjusts it for the changed
data structures.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Release rt2x00 2.2.1

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: skb->data pointer should not include TX descriptor

Make sure the skb->data pointer points to the frame data, not the TX
descriptor. The frame dumping code relies on that.

Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Add Signal type flag

Instead of using the PLCP flag to indicate if the
signal value is plcp or the bitrate we should add
a new flag to mark the bitrate type explicitely.
This is usefull when new types are added later for
rt2800.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Initialize txop during conf_tx() callback

The txop parameter is supported by rt61pci and rt73usb,
and thus should be written to the register instead
of using the fixed value set during initialization.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Only configure hardware when radio is enabled

Some hardware configuration registers such as antenna and channel configuration
can only be written when the radio is enabled. Previously, we didn't consider
this, so some configuration items could be set inconsistently after reenabling
the radio. This patch changes the config() handler to only reprogram the
hardware when the radio is enabled. Configuration changes that are made while
the radio is off are postponed until the radio is switched back on. We also
leave the radio turned off during initialization and only enable it when
requested by mac80211. This allows us to get rid of the DIRTY_CONFIG flag,
because the device is now guaranteed to be completely initialized when brought
up by mac80211.

Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Map extra_tx_headroom to DMA

If a driver requests additional headroom it should
be mapped to DMA as well because it will be send to
the hardware as well (as form of extra descriptor).

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix race conditions in flag handling

Some of the flags should be accessed atomically to
prevent race conditions. The flags that are most important
are those that can change often and indicate the actual
state of the device, queue or queue entry.

The big flag rename was done to move all state flags to
the same naming type as the other rt2x00dev flags and
made sure all places where the flags were used were changed. ;)

Thanks to Stephen for most of the queue flags updates,
which fixes some of the most obvious consequences of the
race conditions. Among those the notorious:

rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.

Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: use the common frame control functions

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rfkill: rename rfkill_mutex to rfkill_global_mutex

rfkill_mutex and rfkill->mutex are too easy to confuse with each other.

Rename rfkill_mutex to rfkill_global_mutex, so that they are easier to tell
apart with just one glance.

Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rfkill: add WARN and BUG_ON paranoia (v2)

BUG_ON() and WARN() the heck out of buggy drivers calling into the rfkill
subsystem.

Also switch from WARN_ON(1) to the new descriptive WARN().

Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rfkill: add missing line break

Trivial patch adding a missing line break on
rfkill_claim_show().

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.co>
Signed-off-by: John W. Linville <linville@tuxdriver.com>