git.stricted.de - GitHub/moto-9609/android_kernel_motorola

mwifiex: add support for Marvell USB8797 chipset

This patch supports Avastar 88W8797 chipset with USB interface.

The corresponding firmware image file is located at:
"mrvl/usb8797_uapsta.bin"

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix STA channel width field

According to IEEE 802.11 8.4.2.59, set the "STA channel width" bit to 0
if transmitting STA is using a 20mhz channel.

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: don't set mesh peer ht caps if ht disabled

Blindly setting ht caps on a mesh peer's station entry would result in
MCS rates being used by the rate control algorithm even if no ht had
been configured. Fix this by checking the channel type before assigning
ht capabilites.

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: refactor mesh peer rate handling

To avoid passing supp_rates and basic_rates around all the time, just
derive these when needed in mesh_matches_local() and mesh_peer_init().

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: refactor mesh peer initialization

This patch unifies the previous two paths toward mesh peer creation a
bit. It also fixes a bug where a peer's changing rates or HT mode
wouldn't register on leaving and then returning to the mesh with a sta
entry still present.

Also clean up locking and clear possibly stale ht cap.

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix TX power reporting on AR9003 chips

The current code unconditionally reads the target
power values for all modes from the EEPROM. However
In 'ar9003_hw_set_power_per_rate_table' the regulatory
caps are applied only on a mode specific subset of the
power values.

The reported TX power level is calculated from the
maximum of the power values. Because some of these
values are uncapped in certain cases, the reported
TX power will be wrong.

On the older chipset, we don't have such problems
because only the mode specific subset of the power
levels are retrieved from the EEPROM on those. Do
the same for the AR9003 chips to fix the issue.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas CS: convert to asynchronous firmware loading

Signed-off-by: Daniel Drake <dsd@laptop.org>
Tested-by: Dan Williams <dcbw@redhat.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix compile warnings when DEBUGFS is disabled.

This fixes two compile warnings, and removes a useless
cast when assigning the 'sc' variable.

Reported-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Support on-channel scan option.

This based on an idea posted by Stanislaw Gruszka,
though I accept full blame for the implementation!

This has been tested with ath9k.

The idea is to let users scan on the current operating
channel without interrupting normal traffic more than
absolutely necessary (changing power level might reset
some hardware, for instance).

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: rt2x00: rt2800usb more devices were identified

found in 2012_03_22_RT5572_Linux_STA_v2.6.0.0_DPO

RT3070:
(0x2019,0x5201) Planex Communications, Inc. RT8070
(0x7392,0x4085) 2L Central Europe BV 8070
7392 is Edimax

RT35xx:
(0x1690,0x0761) Askey
was Fujitsu Stylistic 550, but 1690 is Askey

Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add possible wiphy interface combinations

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: rt2x00: rt2800usb add more devices ids

They were taken from ralink drivers:
2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO
2012_03_22_RT5572_Linux_STA_v2.6.0.0_DPO

0x1eda,0x2210 RT3070 Airties

0x083a,0xb511 RT3370 Panasonic
0x0471,0x20dd RT3370 Philips

0x1690,0x0764 RT35xx Askey
0x0df6,0x0065 RT35xx Sitecom
0x0df6,0x0066 RT35xx Sitecom
0x0df6,0x0068 RT35xx Sitecom

0x2001,0x3c1c RT5370 DLink
0x2001,0x3c1d RT5370 DLink

2001 is D-Link not Alpha

Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: move iwl_rxon_context_id to user

It can be moved to iwl-dev.h since it is op_mode specific.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: improve TX cache footprint

Having cmd[], meta[] and skbs[] as separate arrays
in the TX queue structure is cache inefficient as
we need the data for a given entry together.

To improve this, create an array with these three
members (allocate meta as part of that struct) so
we have the data we need together located together
improving cache footprint.

The downside is that we need to allocate a lot of
memory in one chunk, about 10KiB (on 64-bit) which
isn't very efficient.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: split between AGG_ON and AGG_STARTING

This allows not to notify the transport about aggregation stopped
while aggregation haven't been started.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: Remove inconsistent and redundant declaration

Remove declaration of iwl_alloc_traffic_mem from iwl-agn.h,
from methods that was exposed to support MVM.

MVM doesn't have to use this declaration.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: Added foreward declaration for iwl_cfg in op_mode

Please merge this with "iwlwifi: op_mode holds its pointer
to the config"

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: Change disable calibration bit-set to enum

Changed disable calibration bit field defines to enum.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: remove unneeded includes

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: remove the shared area

It is not needed any more.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: don't use shared for the logger any more

Each modules will hold a pointer to struct device instead.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: driver holds its pointer to the transport

Instead of using the shared area that we be killed.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: transport holds its pointer to the config

Instead of using the shared area that we be killed.
Remove the pointer to config from shared since it is not
used any more.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: driver holds its pointer to the config

Instead of using the shared area that will be killed.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: op_mode holds its pointer to the config

Instead of using the shared area that we be killed.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: op_mode holds its pointer to the transport

Instead of using the shared area that we be killed.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: kill shrd->drv, driver points to transport

The driver layer now holds a pointer to the transport,
and shrd->drv is not needed any more, so kill it.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

mwifiex: corrections in timestamp related code

We get two timing related fields for each bss from firmware in scan
results.
1) timestamp - Actual timestamp information in probe response/beacon
2) network_tsf - firmware's TSF value at the time the beacon or probe
response was received.
Both are needed while associating by firmware.

The patch takes care of following things.
1) We should pass "timestamp" to cfg80211_inform_bss(), but currently
"network_tsf" is being provided. This error is corrected here.
2) Rename "network_tsf" to "fw_tsf"
3) Make use of u64 variable instead of an array of u8/u32 to save
parsed "timestamp" information.
4) Use timestamp provided to stack in scan results using
cfg80211_inform_bss() while associating. (bss->tsf)
5) Allocate space to save fw_tsf in "priv" of cfg80211_bss
and retrieve it while associating.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: code cleanup in BSS handling

Rearrange some code to save extra parameters to the functions.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas USB: convert to asynchronous firmware loading

Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas SDIO: convert to asynchronous firmware loading

Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: add asynchronous firmware loading capability

As described at
http://article.gmane.org/gmane.linux.kernel.wireless.general/86084
libertas is taking a long time to load because it loads firmware
during module loading.

Add a new API for interface drivers to load their firmware
asynchronously. The same semantics of the firmware table are followed
like before.

Interface drivers will be converted in follow-up patches, then we can
remove the old, synchronous firmware loading function.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: harden-up exit paths

These simple sanity check avoids extra complexity in error paths when
moving to asynchronous firmware loading (which means the device may fail to
init some time after its creation).

Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: Firmware loading simplifications

Remove the ability to pass module parameters with firmware filenames
for USB and SDIO interfaces.

Remove the ability to pass custom "user" filenames to lbs_get_firmware().

Remove the ability to reprogram internal device memory with a different
firmware from the USB driver (we don't know of any users), and simplify
the OLPC firmware loading quirk to simply placing the OLPC firmware
at the top of the list (we don't know of any users other than OLPC).

Move lbs_get_firmware() into its own file.

These simplifications should have no real-life effect but make the
upcoming transition to asynchronous firmware loading considerably less
painful.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Don't let mac80211 send a BAR when an AMPDU subframe fails

There are connection stalls or very poor throughputs with rt2800
hardware using 802.11n in AP mode since patch "mac80211: retry sending
failed BAR frames later instead of tearing down aggr"[1][2].

Since rt2800 hardware is not able to correctly report the tx status of
BAR frames, this patch removes as workaround the existing error handling
on AP side, which lets mac80211 send a BAR when an AMPDU subframe fails.

As a result, most wifi clients (aside from Intel STAs on Windows)
instead will timeout now the reorder buffer and request the lost frame
again.

The correct solution would be, to tear down BA session on AP side.

This patch was born on the basis of "[RFT] rt2x00: Tear down BA
session on QoS frame failure"[3].

Thanks to Helmut Schaa for his support!

[1] http://thread.gmane.org/gmane.linux.kernel.wireless.general/83297/focus=83304
[2] http://git.kernel.org/?p=linux/kernel/git/linville/wireless-testing.git;a=commit;h=f0425beda4d404a6e751439b562100b902ba9c98
[3] http://thread.gmane.org/gmane.linux.drivers.rt2x00.user/569

Signed-off-by: Andreas Hartmann <andihartmann@01019freenet.de>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: use ath9k_hw_fbin2freq instead of FBIN2FREQ

The FBIN2FREQ macro and the ath9k_hw_fbin2freq function
does the same thing. Remove the macro, and use the inline
function instead.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: move ath9k_hw_fbin2freq function to eeprom.h

Both eeprom.c and ar9003_eeprom.c has an indentical
'ath9k_hw_fbin2freq' function. Move the function to
a common place and remove the duplicates.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove unused PWRINC_*_TO_*_CHAIN defines

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: merge power correction constants

The existing constants are used for reduction/increase
tx power level on devices with 2x2 and 3x3 chainmask.

Both reduction and increase must use the same value, so
it makes no sense to use separate constants for them.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/libertas/if_usb.c: add missing debugging code

Add a corresponding leave call on error failure.

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: remove get_cmd_string

The command strings are needed through the layers for
debug and error messages, but can differ with opmode.
As a result, we need to give the command names to the
transport layer as configuration.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: optimize struct iwl_cmd_meta layout

Having a u32 before a potential 64-bit value is
not very efficient, move it last.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: expose static methods for MVM use

To support hybrid state of MVM op_mode, most of the functioanallity
will be done using DVM functions.

When MVM will have independant live, the declarations will be removed
and the functions will be static back.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: phy db channel to tx power channel group

Implement mapping of channel to TX power channel group,
for sending channel specific data before add context.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: Disabling calibrations variable

Add a variable for disabling specific calibrations.
Merged old variables for calibrations disabling.

Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: remove uneeded include from iwl-pci.c

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: remove double verification of ucode sections

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: set size of ucode section

Set size of firmware section in mvm bundle format.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: remove iwl_tx_queue declaration

The declaration isn't needed as the struct is only
used in code that includes the right header file.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: move status definitions from iwl-shared

The code has been changed, move the definitions to the proper file
being used by the code.

Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: added HBUS_TARG_TEST_REG

This register is used to enable some debug mechanisms.

Signed-off-by: Amit Beka <amit.beka@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: move HCMD_ACTIVE to trans

The HCMD_ACTIVE bit is only used in trans.

Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: complete STATUS_READY refactoring

When WiMax takes over the RF, inform the op_mode.

Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: remove antenna from mod params struct

It doesn't even exist as a module parameter,
so just remove the item from the struct.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: remove uCode alternatives mechanism

We've never released firmware using the alternatives
mechanism and our build process makes that difficult
anyway. This means that in every file we have ever
built (except maybe by hand for testing) the listed
alternative was 0. Make the alternative field in the
TLVs part of the TLV number (thus expanding that to
32 bits); this gives us more TLV numbers (not really
needed) and more importantly protects against rogue
firmware files that actually do use the alternatives
mechanism -- those will now be rejected since they
don't contain any valid TLVs.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: remove no_sleep_autoadjust

My original idea with this was to adjust the sleep
pattern of the uCode based on the maximum network
latency userspace asked for. Due to nobody wanting
to test it, this logic was disabled by default. It
seems the time has come to remove it, since it's
not only always disabled but there also don't seem
to be any applications that actually request a max
network latency.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

wireless: rt2x00: rt2800pci add more RT539x ids

RT539x devices:
(0x1814, 0x5362)
(0x1814, 0x5392)

Taken from ralink driver 2011_0406_RT5390_RT5392_Linux_STA_V2.5.0.3_DPO

Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: rt2x00: rt{2500,73}usb.c put back duplicate id

put back 0x050d,0x7050 to rt73usb, same usb_id for two chips:

K7SF5D7050A ver 2xxx is rt2500
K7SF5D7050B ver 3xxx is rt73

<http://en-us-support.belkin.com/app/answers/detail/a_id/297/kw/K7SF5D7050>

Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: simplify ath9k_hw_get_scaled_power function

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: introduce ath9k_hw_get_scaled_power helper

The computation of the scaled power value in
various eeprom files uses identical code. Move
that code into a helper function and use that
instead of code duplication.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: use consistent value for REDUCE_SCALED_POWER_BY_THREE_CHAIN

The REDUCE_SCALED_POWER_BY_THREE_CHAIN symbol is
defined in different eeprom files, and the value
varies between the different files.

In eeprom_def.c and in ar9003_eeprom.c the value
of the symbol is 9, however the comments in these
files indicates the value should be 10*log10(3)*2
which is 9.54242509439325. Replace the the value
to 10 in these files.

Also add comments to eeprom_9287.c.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: use ath9k_hw_update_regulatory_maxpower in ath9k_hw_def_set_txpower

We have a helper function for updating the max_power_level
value. Use that and remove the duplicated code.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net/wireless: use module_pci_driver

This patch converts the drivers in drivers/net/wireless/* to use
module_pci_driver() macro which makes the code smaller and a bit simpler.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Simon Kelley <simon@thekelleys.org.uk>
Cc: Jouni Malinen <j@w1.fi>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add function retrieve average rssi

Add utility function to provide the average rssi per vif

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192ce: Remove false positives for kmemleak

When rtl8192ce is in operation, kmemleak indicates a number of leaks, yet
when the driver is removed all are gone. These false positives happen
in two locations:

unreferenced object 0xffff880041124000 (size 9536):
  comm "work_for_cpu", pid 9295, jiffies 4295037203 (age 20596.320s)
  hex dump (first 32 bytes):
    33 00 00 01 01 6d 00 00 00 00 b1 0e 21 0b 00 00  3....m......!...
    01 01 6d 00 00 00 00 8b 20 c0 e9 00 00 01 01 6d  ..m..... ......m
  backtrace:
    [<ffffffff8137a1b1>] kmemleak_alloc+0x21/0x50
    [<ffffffff8138d01f>] kmalloc_large_node+0x9a/0xa6
    [<ffffffff811335a5>] __kmalloc_node_track_caller+0x175/0x3b0
    [<ffffffff812ddfe3>] __alloc_skb+0x73/0x230
    [<ffffffff812de1b8>] dev_alloc_skb+0x18/0x30
    [<ffffffffa091a3b7>] rtl_pci_probe+0x10e0/0x17d2 [rtlwifi]
-- snip --
unreferenced object 0xffff8800b4d3f600 (size 256):
  comm "kworker/u:2", pid 13221, jiffies 4297830173 (age 9424.568s)
  hex dump (first 32 bytes):
    1c d6 45 b1 00 88 ff ff 1c d6 45 b1 00 88 ff ff  ..E.......E.....
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff8137a1b1>] kmemleak_alloc+0x21/0x50
    [<ffffffff81130f43>] kmem_cache_alloc_node+0x153/0x270
    [<ffffffff812ddfb6>] __alloc_skb+0x46/0x230
    [<ffffffff812de1b8>] dev_alloc_skb+0x18/0x30
    [<ffffffffa093264a>] rtl92c_set_fw_rsvdpagepkt+0x22a/0x5c0 [rtl8192c_common]
-- snip --

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: add PCI id

This device works fine of ath5k.

Details bellow
05:00.0 0200: 168c:ff1b (rev 01)
05:00.0 Ethernet controller: Atheros Communications Inc. Device ff1b (rev 01)
Flags: bus master, fast devsel, latency 0, IRQ 19
Memory at febf0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath5k

ath5k 0000:05:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ath5k 0000:05:00.0: setting latency timer to 64
ath5k 0000:05:00.0: registered as 'phy0'
ath: EEPROM regdomain: 0x67
ath: EEPROM indicates we should expect a direct regpair map
ath: Country alpha2 being used: 00
ath: Regpair used: 0x67
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70)

Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix beacon descriptor

The tx interrupt for beacon queue is configured only for edma chips.
As the edma chip does not support per descriptor interrupt, no need to
set INTREQ for every beacon descriptor. And also clear ps filter for
beacon frame.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: skip beaconing when reset work is pending

Whenever the reset work is queued up, do not generate beacon. And also
clear the beacon miss count once the beacon stuck was observed.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: reset noiseimmunity level to default

After the chip reset, the noise immunity levels are restored with
history values. If the immunity levels are lower than the defaults,
lets start with the optimal values.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: increse bss expire time

The background scan completion takes more time when the station is
having heavy uplink traffic. The scan state machine decides to fall
back to home channel on every off-channel visit when there are pending
frames in tx queue. bgscan completion took ~30sec on dual band US
regulatory card.

scan period = (20 active channels * probe timeout) +
              (12 passive channels * passive probe timeout) +
              (32 * timeout on home channel) +
              (32 * flush timeout)

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix ibss beacon next tbtt

Sync-up ibss beacon timer with the beacon frame's timestamp. When the
node acts as joiner, it has to sync with the received beacon timestamp
instead of reading tsf from hw. As the hw tsf wont wont be update till
bssid is configured. This patch programs hw tsf with the received beacon
timestamp if beacon timers are yet to be configured.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix ibss fair beacon distribution for AR9462

Update AR9462 initval to fix unbalance beacon distribution
in Ad-Hoc network.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

hostap: GFP_ATOMIC/GFP_KERNEL cleanup

The driver is allocating memory during initialization with GFP_ATOMIC
even though GFP_KERNEL is sufficient. This patch fixes it.

Signed-off-by: Matt Renzelmann <mjr@cs.wisc.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Take into account TSF adjustment latency in Toffset setpoint

When testing mesh synchronization we observed a global TSF slowdown that
was dependent on the number of synchronized mesh stations. This seems
to be caused by the TSF adjustment (read/write) latency.

Adding a small margin to the Toffset setpoint solved the problem.

Signed-off-by: Shinichi Hotori <hotorinn@gmail.com>
Signed-off-by: Yu Niiro <yu.niiro@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Choose a new toffset setpoint if a big tsf jump is detected.

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211_hwsim: fixup for tsf setting

Last patch I sent failed to take into account the offset of each phy.

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Set the correct values for hwmp (1) and airtimeLinkMetric (1)

Per sections 8.4.2.100.2 and 8.4.2.100.3 of Std 802.11-2012

Reported-by: Shinichi Hotori <hotorinn@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: optimize the hardware hang check

Since it's only called when beacons are stuck, move it to the SWBA handler
tasklet, to avoid doing redundant checks on every single interrupt.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: do not register LEDs on AR913x

LED support is typically handled via system GPIO on these platforms.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: add support for 8 AP mode interfaces

Also tweak beacon response times for better stability with the shorter
timer intervals.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: use compare_ether_addr on MAC addresses instead of memcmp

Following Felix's recent patchset as an example I have replaced memcmp with
compare_ether_addr.

"Because of the constant size and guaranteed 16 bit alignment, the inline
compare_ether_addr function is much cheaper than calling memcmp."

Signed-off-by: Jonathan Bither <jonbither@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Gather and report IRQ sync_cause errors.

Report all defined sync_cause errors in debugfs
to aid with debugging.

Use a macro to print out the interrupts file contents
to decrease code duplication.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Use macro to decrease code when priting recv stats.

This hides some repetitive code, and will help if the
column widths ever need to change.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: check IEEE80211_HW_QUEUE_CONTROL in ieee80211_check_queues()

Commit 3a25a8c8 (mac80211: add improved HW queue control) introduced a
bug when running in AP mode without the IEEE80211_HW_QUEUE_CONTROL
flag set. The ieee80211_check_queues() function always returns
-EINVAL, preventing AP mode from starting. To fix this, check whether
this flag is set before checking if cab_queue is set properly.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: enforce lack of interface combinations

My grand plan to allow drivers to gradually move over
to advertising virtual interface combinations and only
enforce with drivers that do want it enforced doesn't
seem to be working out, only Christian ever added the
advertising (to carl9170), nobody else did.

Begin enforcing combinations in cfg80211 so that users
can rely on the information reported about a device.

Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next' of git://git./linux/kernel/git/iwlwifi/iwlwifi

brcm80211: smac: only provide valid regulatory hint

The driver provides a regulatory hint to cfg80211 as obtained from the
SPROM. Mostly, this will be a two-letter ISO country code. However, it
may obtain special country code similar to the world regulatory domain
as used in cfg80211. This patch avoids setting these special codes as
the hint is lost to cfg80211.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: smac: do not use US as fallback regulatory hint

The brcmsmac driver provides the country code from sprom as a regulatory
hint to cfg80211. When brcmsmac does not find a country code entry in
the sprom it passes 'US' as regulatory hint. Better approach is to rely
on the world regulatory domain in cfg80211/crda.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: clean up chip id table

Remove unsupported chip ID and rearrange the list in alphabetical
order

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: postpone dongle RF enabling.

BRCMF_C_UP is the command that asks the firmware to enable RF of
dongle. Some firmware initialization steps must be performed during
RF is down. Postpone BRCMF_C_UP firing until brcmf_netdev_open get
called to ensure firmware have enough time to finish
initialization.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: add frame header extension support

A header extension is introduced in the received frame to provide
extra space for dongle information. This won't affect current
supported chipset since the data_offset is 0. But it's necessary for
adding support for future chipset.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: register primary net device with device mac address

The primary net device was registered with a primary mac address and
upon IFUP it was set to match the actual mac address from the device.
This patch changes that and moves the brcmf_add_if() call to the common
part of the driver.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: remove primary mac address handling from brcmf_net_attach

The mac address for the primary interface was handled different from
the other interfaces. The code has been restructured such that the
brcmf_net_attach function treats the interfaces equal.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: make brcmf_net_attach() static

The function brcmf_net_attach() is only used within dhd_linux.c so
it does not need to be extern. This patch makes the function static.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: remove ieee80211_rx_bss_get

its not used where, while we directly obtain ieee80211_bss's
pointer in ibss.c by calling cfg80211_get_bss

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Add Panasonic N5HBZ0000055 device id

Reported-by: Ryan Roper <ryan.roper@gmail.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: remove hw.conf.channel usage where possible

Removes hw.conf.channel usage from the following functions:
* ieee80211_mandatory_rates
* ieee80211_sta_get_rates
* ieee80211_frame_duration
* ieee80211_rts_duration
* ieee80211_ctstoself_duration

This is in preparation for multi-channel operation.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Remove BTCOEX initvals

The MAX_TXPWR table for BTCOEX is not needed for AR9462.
Programming these values to the HW results in undesirable
behavior - for example, large number of delimiter/data
underruns are seen in AES-CCMP mode. Also, registers like
AR_PCU_MISC_MODE2 return 0xdeadbeef after the BTCOEX_MAX
power table is programmed to the HW, and frames being transmitted
end up being looped back to the RX engine, an example being beacon
frames in IBSS mode.

Remove this table for now - this fixes CCMP performance and general
IBSS usage.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix an issue in ieee80211_tx_info count field management

I noticed a possible issue in the status count field management of the
ieee80211_tx_info data structure. In particular, when the AGGR
processing is employed,
status.rates[].count is set just for the first frame and not for
others belonging to the same burst, leading to wrong statistic data in
the mac80211 debug file system.

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>