[media] tda18271: make 'low-power standby mode after attach' multi-instance safe

Ensure that unnecessary features are powered down at the end of the
attach() function on attach of the tuner's first instance. If the
configuration requires the loop thru or xtout features, they will
remain enabled.
This must *only* be done after attaching the first instance of the tuner.
If there are multiple instances of the tuner, the bridge driver will need
to maintain power managament by itself.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tda18271: enter low-power standby mode at the end of tda18271_attach()

Ensure that unnecessary features are powered down at the end of the
attach() function.  If the configuration requires the loop thru or
xtout features, they will remain enabled.
Thanks to Antti Palosaari for noticing the additional power consumption.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ivtv: fix format enumeration: don't show invalid formats

Depending on the device node only the compressed or the uncompressed format
should be shown, not both.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ivtv: disable a bunch of ioctls that are invalid for the decoder VBI

The VBI capture for the decoder (/dev/vbi8) is special in that it captures
the VBI stream embedded in an MPEG stream that is being decoded.
A lot of the ioctls that would normally be valid have to be disabled since
they make no sense for such a device, and v4l2-compliance will complain
about that.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ivtv: fix incorrect service_set for the decoder VBI capture

Found with v4l2-compliance.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ivtv: don't allow g/s_frequency for output device nodes

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ivtv: fix v4l2-compliance errors for the radio device

- fix error code when attempting to read from write-only streams.
- fix error code when attempting to write to read-only streams.
- don't start capturing when polling on a radio node.
- give the radio node its own file operations struct.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ivtv: fix v4l2-compliance error: inconsistent std reporting

The tuner input has a different standard mask than a S-Video or Composite input.
Changing the standard should change tvnorms as well for all device nodes.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ivtv: DECODER_CMD v4l2-compliance fixes

VIDIOC_DECODER_CMD didn't return EPERM when calling PAUSE or RESUME if no
decoding is in progress.
VIDIOC_G_ENC_INDEX didn't set entries_cap or return 0 if no decoding was
in progress.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] sliced vbi: subdevs shouldn't clear the full v4l2_sliced_vbi_format struct

Various subdevs cleared the full v4l2_sliced_vbi_format struct, when
only the service_set/lines fields should have been cleared.
Due to this the io_size field was wrongly cleared to 0, causing a
v4l2-compliance error.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l2-ctrls: add a filter function to v4l2_ctrl_add_handler

With a filter function you can control more precisely which controls
are added. This is useful in particular for radio device nodes for
combined TV/Radio cards where you want to show just the radio-specific
controls and not controls like brightness.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rtl28xxu: [0ccd:00d3] TerraTec Cinergy T Stick RC (Rev. 3)

It is RTL2832U + E4000.
Thanks to Nikolai Spasov reporting and testing!

Reported-by: Nikolai Spasov <ns@codingrobot.com>
Tested-by: Nikolai Spasov <ns@codingrobot.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] fc2580: use macro for 64 bit division and reminder

Fixes the following warnings on a 32 bit system with GCC 4.4.3 and kernel Ubuntu 2.6.32-43 32 bit:
WARNING: "__udivdi3" [fc2580.ko] undefined!
WARNING: "__umoddi3" [fc2580.ko] undefined!

Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] fc2580: silence uninitialized variable warning

fc2580.c: In function 'fc2580_set_params':
fc2580.c:118: warning: 'ret' may be used uninitialized in this function

Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] fc2580: define const as UL to silence a warning

fc2580.c: In function 'fc2580_set_params':
fc2580.c:150: warning: this decimal constant is unsigned only in ISO C90

Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: do not set PCTV 290e LNA handler if fe attach fail

It was a bug that could cause oops if demodulator attach was
failed.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cxd2820r: use static GPIO config when GPIOLIB is undefined

It is fallback condition as GPIOLIB seems to be disabled by default.
Better solution is needed, maybe GPIOLIB could be enabled by default?

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: implement FE set_lna() callback

Make LNA run-time switching possible for PCTV nanoStick T2 290e!

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] MAINTAINERS: Add stk1160 driver

Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] MAINTAINERS: add modules I am responsible

All those are media modules, mostly digital television drivers.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l2-ioctl.c: fix overlay support

The vidioc_overlay op needs an unsigned int, not an unsigned int pointer.
So we need a small function that dereferences the unsigned int pointer.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media/radio/shark2: Fix build error caused by missing dependencies

Without this patch, building rand-0y2jSKT results in:

WARNING: drivers/usb/musb/musb_hdrc.o(.devinit.text+0x9b8): Section mismatch in reference from the function musb_init_controller() to the function .init.text:dma_controller_create()
The function __devinit musb_init_controller() references
a function __init dma_controller_create().
If dma_controller_create is only used by musb_init_controller then
annotate dma_controller_create with a matching annotation.

ERROR: "snd_tea575x_init" [drivers/media/radio/radio-shark.ko] undefined!
ERROR: "snd_tea575x_exit" [drivers/media/radio/radio-shark.ko] undefined!
make[2]: *** [__modpost] Error 1
make[1]: *** [modules] Error 2
make: *** [sub-make] Error 2

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-mfc: Fix second memory bank alignment

Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Fix setup of initial links to FIMC entities

This patch fixes regression introduced in commit
4af813108b880e96a4b8b01e162f950a4aaa2475. Missing pointers
to the sensor subdevs are restored along with subdev callback
notifications to a corresponding FIMC instance driver.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Fix cast warnings from m5mols_[set/get]_ctrl_mode

Fixes following warnings on 64-bit architectures:

m5mols.h: In function 'm5mols_set_ctrl_mode':
m5mols.h:326:15: warning: cast to pointer from integer of different
size [-Wint-to-pointer-cast]

m5mols.h: In function 'm5mols_get_ctrl_mode':
m5mols.h:331:9: warning: cast from pointer to integer of different
size [-Wpointer-to-int-cast]

drivers/media/i2c/m5mols/m5mols_controls.c:466:2: warning: cast
from pointer to integer of different size

Cc: Heungjun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Add missing free_irq() on error path

Make sure the interrupt is freed when driver probing fails.

Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Don't allocate fimc-m2m video device dynamically

There is no need to to dynamically allocate struct video_device
for the M2M devices, so embed it instead in driver's private
data structure as it is done in case of fimc-capture and fimc-lite,
where it solves some bugs on cleanup paths.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Don't allocate fimc-capture video device dynamically

This fixes potential invalid pointer de-reference, when
media_entity_cleanup() is called before video device
is unregistered.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Don't allocate fimc-lite video device structure dynamically

This fixes potential invalid pointer de-reference, when
media_entity_cleanup() is called after video_unregister_device,
and video device structure memory is already freed.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Enable FIMC-LITE driver only for SOC_EXYNOS4x12

Allow to compile-in the FIMC-LITE driver only on Exynos4212,
Exynos4412 and Exynos5250 SoC where the device is available.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Merge tag 'v3.6' into staging/for_v3.7

Linux 3.6

* tag 'v3.6': (562 commits)
  Linux 3.6
  vfs: dcache: fix deadlock in tree traversal
  mtdchar: fix offset overflow detection
  thp: avoid VM_BUG_ON page_count(page) false positives in __collapse_huge_page_copy
  iommu/amd: Fix wrong assumption in iommu-group specific code
  netdev: octeon: fix return value check in octeon_mgmt_init_phy()
  ALSA: snd-usb: fix next_packet_size calls for pause case
  inetpeer: fix token initialization
  qlcnic: Fix scheduling while atomic bug
  bnx2: Clean up remaining iounmap
  trivial select_parent documentation fix
  net: phy: smsc: Implement PHY config_init for LAN87xx
  smsc75xx: fix resume after device reset
  um: Preinclude include/linux/kern_levels.h
  um: Fix IPC on um
  netdev: pasemi: fix return value check in pasemi_mac_phy_init()
  team: fix return value check
  l2tp: fix return value check
  USB: Fix race condition when removing host controllers
  USB: ohci-at91: fix null pointer in ohci_hcd_at91_overcurrent_irq
  ...

tda1004x: Lock I2C bus during firmware load

tda1004x doesn't allow firmware loads while it is busy with something
else. Avoid it to happen by locking the I2C bus during firmware transfer.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Linux 3.6

vfs: dcache: fix deadlock in tree traversal

IBM reported a deadlock in select_parent().  This was found to be caused
by taking rename_lock when already locked when restarting the tree
traversal.

There are two cases when the traversal needs to be restarted:

 1) concurrent d_move(); this can only happen when not already locked,
    since taking rename_lock protects against concurrent d_move().

 2) racing with final d_put() on child just at the moment of ascending
    to parent; rename_lock doesn't protect against this rare race, so it
    can happen when already locked.

Because of case 2, we need to be able to handle restarting the traversal
when rename_lock is already held.  This patch fixes all three callers of
try_to_ascend().

IBM reported that the deadlock is gone with this patch.

[ I rewrote the patch to be smaller and just do the "goto again" if the
  lock was already held, but credit goes to Miklos for the real work.
   - Linus ]

Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'iommu-fixes-v3.6-rc7' of git://git./linux/kernel/git/joro/iommu

Pull IOMMU fixes from Joerg Roedel:
 "Two small patches:

* One patch to fix the function declarations for
  !CONFIG_IOMMU_API. This is causing build errors
  in linux-next and should be fixed for v3.6.

* Another patch to fix an IOMMU group related NULL pointer
  dereference."

* tag 'iommu-fixes-v3.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/amd: Fix wrong assumption in iommu-group specific code
  iommu: static inline iommu group stub functions

Merge git://git.infradead.org/users/willy/linux-nvme

Pull NVMe driver fixes from Matthew Wilcox:
 "Now that actual hardware has been released (don't have any yet
  myself), people are starting to want some of these fixes merged."

Willy doesn't have hardware? Guys...

* git://git.infradead.org/users/willy/linux-nvme:
  NVMe: Cancel outstanding IOs on queue deletion
  NVMe: Free admin queue memory on initialisation failure
  NVMe: Use ida for nvme device instance
  NVMe: Fix whitespace damage in nvme_init
  NVMe: handle allocation failure in nvme_map_user_pages()
  NVMe: Fix uninitialized iod compiler warning
  NVMe: Do not set IO queue depth beyond device max
  NVMe: Set block queue max sectors
  NVMe: use namespace id for nvme_get_features
  NVMe: replace nvme_ns with nvme_dev for user admin
  NVMe: Fix nvme module init when nvme_major is set
  NVMe: Set request queue logical block size

get_dvb_firmware: fix download site for tda10046 firmware

The previous website doesn't exist anymore. Update it to one site that
actually exists.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

mtdchar: fix offset overflow detection

Sasha Levin has been running trinity in a KVM tools guest, and was able
to trigger the BUG_ON() at arch/x86/mm/pat.c:279 (verifying the range of
the memory type).  The call trace showed that it was mtdchar_mmap() that
created an invalid remap_pfn_range().

The problem is that mtdchar_mmap() does various really odd and subtle
things with the vma page offset etc, and uses the wrong types (and the
wrong overflow) detection for it.

For example, the page offset may well be 32-bit on a 32-bit
architecture, but after shifting it up by PAGE_SHIFT, we need to use a
potentially 64-bit resource_size_t to correctly hold the full value.

Also, we need to check that the vma length plus offset doesn't overflow
before we check that it is smaller than the length of the mtdmap region.

This fixes things up and tries to make the code a bit easier to read.

Reported-and-tested-by: Sasha Levin <levinsasha928@gmail.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Artem Bityutskiy <dedekind1@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge git://git./linux/kernel/git/davem/net

Pull networking fixes from David S Miller:

 1) Netfilter xt_limit module can use uninitialized rules, from Jan
    Engelhardt.

 2) Wei Yongjun has found several more spots where error pointers were
    treated as NULL/non-NULL and vice versa.

 3) bnx2x was converted to pci_io{,un}map() but one remaining plain
    iounmap() got missed.  From Neil Horman.

 4) Due to a fence-post type error in initialization of inetpeer entries
    (which is where we store the ICMP rate limiting information), we can
    erroneously drop ICMPs if the inetpeer was created right around when
    jiffies wraps.

    Fix from Nicolas Dichtel.

 5) smsc75xx resume fix from Steve Glendinnig.

 6) LAN87xx smsc chips need an explicit hardware init, from Marek Vasut.

 7) qlcnic uses msleep() with locks held, fix from Narendra K.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  netdev: octeon: fix return value check in octeon_mgmt_init_phy()
  inetpeer: fix token initialization
  qlcnic: Fix scheduling while atomic bug
  bnx2: Clean up remaining iounmap
  net: phy: smsc: Implement PHY config_init for LAN87xx
  smsc75xx: fix resume after device reset
  netdev: pasemi: fix return value check in pasemi_mac_phy_init()
  team: fix return value check
  l2tp: fix return value check
  netfilter: xt_limit: have r->cost != 0 case work

Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs

Pull vfs fixes from Al Viro:
 "A couple of fixes; one for automount/lazy umount race, another a
  classic "we don't protect the refcount transition to zero with the
  lock that protects looking for object in hash" kind of crap in lockd."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  close the race in nlmsvc_free_block()
  do_add_mount()/umount -l races

Merge branch 'for-linus-3.6-rc-final' of git://git./linux/kernel/git/rw/uml

Pull UML fixes from Richard Weinberger.

* 'for-linus-3.6-rc-final' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: Preinclude include/linux/kern_levels.h
  um: Fix IPC on um
  um: kill thread->forking
  um: let signal_delivered() do SIGTRAP on singlestepping into handler
  um: don't leak floating point state and segment registers on execve()
  um: take cleaning singlestep to start_thread()

Merge tag 'dm-3.6-fixes' of git://git./linux/kernel/git/agk/linux-dm

Pull dm fixes from Alasdair G Kergon:
 "A few fixes for problems discovered during the 3.6 cycle.

  Of particular note, are fixes to the thin target's discard support,
  which I hope is finally working correctly; and fixes for multipath
  ioctls and device limits when there are no paths."

* tag 'dm-3.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
  dm verity: fix overflow check
  dm thin: fix discard support for data devices
  dm thin: tidy discard support
  dm: retain table limits when swapping to new table with no devices
  dm table: clear add_random unless all devices have it set
  dm: handle requests beyond end of device instead of using BUG_ON
  dm mpath: only retry ioctl when no paths if queue_if_no_path set
  dm thin: do not set discard_zeroes_data

thp: avoid VM_BUG_ON page_count(page) false positives in __collapse_huge_page_copy

Speculative cache pagecache lookups can elevate the refcount from
under us, so avoid the false positive. If the refcount is < 2 we'll be
notified by a VM_BUG_ON in put_page_testzero as there are two
put_page(src_page) in a row before returning from this function.

Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Petr Holasek <pholasek@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

iommu/amd: Fix wrong assumption in iommu-group specific code

The new IOMMU groups code in the AMD IOMMU driver makes the
assumption that there is a pci_dev struct available for all
device-ids listed in the IVRS ACPI table. Unfortunatly this
assumption is not true and so this code causes a NULL
pointer dereference at boot on some systems.

Fix it by making sure the given pointer is never NULL when
passed to the group specific code. The real fix is larger
and will be queued for v3.7.

Reported-by: Florian Dazinger <florian@dazinger.net>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>

netdev: octeon: fix return value check in octeon_mgmt_init_phy()

In case of error, the function of_phy_connect() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux

Pull drm fixes from Dave Airlie:
 "The three nouveau fixes quiten unneeded dmesg spam that people are
   seeing and pondering,

  The udl fix stops it from trying to driver monitors that are too big,
  where we get a black screen.

  And a vmware memory alloc problem."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/nvc0/fifo: ignore bits in PFIFO_INTR that aren't set in PFIFO_INTR_EN
  drm/udl: limit modes to the sku pixel limits.
  vmwgfx: corruption in vmw_event_fence_action_create()
  drm/nvc0/ltcg: mask off intr 0x10
  drm/nouveau: silence a debug message triggered by newer userspace

Merge tag 'usb-3.6-rc7' of git://git./linux/kernel/git/gregkh/usb

Pull USB fixes from Greg Kroah-Hartman:
 "Here are two USB bugfixes for your 3.6-rc7 tree.

  The OHCI fix has been reported a number of times and is a regression
  from 3.5, and the patch that causes the regression was on the way to
  the -stable trees before I was reminded (again) that this fix needed
  to get to your tree soon.

  The host controller bugfix was reported in older kernels as being
  pretty easy to trigger, and has been tested by Red Hat and their
  customers.

  Both have been in the usb-next branch in the -next tree for a while
  now, I just cherry-picked them out to get to you in time for the 3.6
  release.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: Fix race condition when removing host controllers
  USB: ohci-at91: fix null pointer in ohci_hcd_at91_overcurrent_irq

ALSA: snd-usb: fix next_packet_size calls for pause case

Also fix the calls to next_packet_size() for the pause case. This was
missed in 245baf983 ("ALSA: snd-usb: fix calls to next_packet_size").

Signed-off-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reported-and-tested-by: Christian Tefzer <ctrefzer@gmx.de>
Cc: stable@kernel.org
[ Taking directly because Takashi is on vacation  - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'asoc-3.6' of git://git./linux/kernel/git/broonie/sound

Pull ASoC update from Mark Brown:
 "One small and obvious driver-specific fix.

  Takashi is on vacation now so he asked me to send directly, it's a
  pretty bad bug with low regression risk."

* tag 'asoc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound:
  ASoC: wm2000: Correct register size

inetpeer: fix token initialization

When jiffies wraps around (for example, 5 minutes after the boot, see
INITIAL_JIFFIES) and peer has just been created, now - peer->rate_last can be
< XRLIM_BURST_FACTOR * timeout, so token is not set to the maximum value, thus
some icmp packets can be unexpectedly dropped.

Fix this case by initializing last_rate to 60 seconds in the past.

Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: Fix scheduling while atomic bug

In the device close path, 'qlcnic_fw_destroy_ctx' and
'qlcnic_poll_rsp' call msleep. But  'qlcnic_fw_destroy_ctx' and
'qlcnic_poll_rsp' are called with 'adapter->tx_clean_lock' spin lock
held resulting in scheduling while atomic bug causing the following
trace.

I observed that the commit 012dc19a45b2b9cc2ebd14aaa401cf782c2abba4
from John Fastabend addresses a similar issue in ixgbevf driver.
Adopting the same approach used in the commit, this patch uses mdelay
to address the issue.

[79884.999115] BUG: scheduling while atomic: ip/30846/0x00000002
[79885.005562] INFO: lockdep is turned off.
[79885.009958] Modules linked in: qlcnic fuse nf_conntrack_netbios_ns nf_conntrack_broadcast ipt_MASQUERADE bnep bluetooth rfkill ip6table_mangle ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter ip6_tables iptable_nat nf_nat iptable_mangle ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack iptable_filter ip_tables dcdbas coretemp kvm_intel kvm iTCO_wdt ixgbe iTCO_vendor_support crc32c_intel ghash_clmulni_intel nfsd microcode sb_edac pcspkr edac_core dca bnx2x shpchp auth_rpcgss nfs_acl lpc_ich mfd_core mdio lockd libcrc32c wmi acpi_pad acpi_power_meter sunrpc uinput sd_mod sr_mod cdrom crc_t10dif ahci libahci libata megaraid_sas usb_storage dm_mirror dm_region_hash dm_log dm_mod [last unloaded: qlcnic]
[79885.083608] Pid: 30846, comm: ip Tainted: G        W  O 3.6.0-rc7+ #1
[79885.090805] Call Trace:
[79885.093569]  [<ffffffff816764d8>] __schedule_bug+0x68/0x76
[79885.099699]  [<ffffffff8168358e>] __schedule+0x99e/0xa00
[79885.105634]  [<ffffffff81683929>] schedule+0x29/0x70
[79885.111186]  [<ffffffff81680def>] schedule_timeout+0x16f/0x350
[79885.117724]  [<ffffffff811afb7a>] ? init_object+0x4a/0x90
[79885.123770]  [<ffffffff8107c190>] ? __internal_add_timer+0x140/0x140
[79885.130873]  [<ffffffff81680fee>] schedule_timeout_uninterruptible+0x1e/0x20
[79885.138773]  [<ffffffff8107e830>] msleep+0x20/0x30
[79885.144159]  [<ffffffffa04c7fbf>] qlcnic_issue_cmd+0xef/0x290 [qlcnic]
[79885.151478]  [<ffffffffa04c8265>] qlcnic_fw_cmd_destroy_rx_ctx+0x55/0x90 [qlcnic]
[79885.159868]  [<ffffffffa04c92fd>] qlcnic_fw_destroy_ctx+0x2d/0xa0 [qlcnic]
[79885.167576]  [<ffffffffa04bf2ed>] __qlcnic_down+0x11d/0x180 [qlcnic]
[79885.174708]  [<ffffffffa04bf6f8>] qlcnic_close+0x18/0x20 [qlcnic]
[79885.181547]  [<ffffffff8153b4c5>] __dev_close_many+0x95/0xe0
[79885.187899]  [<ffffffff8153b548>] __dev_close+0x38/0x50
[79885.193761]  [<ffffffff81545101>] __dev_change_flags+0xa1/0x180
[79885.200419]  [<ffffffff81545298>] dev_change_flags+0x28/0x70
[79885.206779]  [<ffffffff815531b8>] do_setlink+0x378/0xa00
[79885.212731]  [<ffffffff81354fe1>] ? nla_parse+0x31/0xe0
[79885.218612]  [<ffffffff815558ee>] rtnl_newlink+0x37e/0x560
[79885.224768]  [<ffffffff812cfa19>] ? selinux_capable+0x39/0x50
[79885.231217]  [<ffffffff812cbf98>] ? security_capable+0x18/0x20
[79885.237765]  [<ffffffff81555114>] rtnetlink_rcv_msg+0x114/0x2f0
[79885.244412]  [<ffffffff81551f87>] ? rtnl_lock+0x17/0x20
[79885.250280]  [<ffffffff81551f87>] ? rtnl_lock+0x17/0x20
[79885.256148]  [<ffffffff81555000>] ? __rtnl_unlock+0x20/0x20
[79885.262413]  [<ffffffff81570fc1>] netlink_rcv_skb+0xa1/0xb0
[79885.268661]  [<ffffffff81551fb5>] rtnetlink_rcv+0x25/0x40
[79885.274727]  [<ffffffff815708bd>] netlink_unicast+0x19d/0x220
[79885.281146]  [<ffffffff81570c45>] netlink_sendmsg+0x305/0x3f0
[79885.287595]  [<ffffffff8152b188>] ? sock_update_classid+0x148/0x2e0
[79885.294650]  [<ffffffff81525c2c>] sock_sendmsg+0xbc/0xf0
[79885.300600]  [<ffffffff8152600c>] __sys_sendmsg+0x3ac/0x3c0
[79885.306853]  [<ffffffff8109be23>] ? up_read+0x23/0x40
[79885.312510]  [<ffffffff816896cc>] ? do_page_fault+0x2bc/0x570
[79885.318968]  [<ffffffff81191854>] ? sys_brk+0x44/0x150
[79885.324715]  [<ffffffff811c458c>] ? fget_light+0x24c/0x520
[79885.330875]  [<ffffffff815286f9>] sys_sendmsg+0x49/0x90
[79885.336707]  [<ffffffff8168e429>] system_call_fastpath+0x16/0x1b

Signed-off-by: Narendra K <narendra_k@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2: Clean up remaining iounmap

commit c0357e975afdbbedab5c662d19bef865f02adc17 modified bnx2 to switch from
using ioremap/iounmap to pci_iomap/pci_iounmap.  They missed a spot in the error
path of bnx2_init_one though.  This patch just cleans that up.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Michael Chan <mcan@broadcom.com>
CC: "David S. Miller" <davem@davemloft.net>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc

Pull one more arm-soc bugfix from Olof Johansson:
 "Here's a bugfix for orion5x.  Without this, PCI doesn't initialize
  properly because of too small coherent pool to cover the allocations
  needed.

  A similar fix has already been done on kirkwood."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: Orion5x: Fix too small coherent pool.

Merge branch 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping

Pull ARM dma-mapping fix from Marek Szyprowski:
 "This patch fixes a potential memory leak in the ARM dma-mapping code."

* 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
  ARM: dma-mapping: Fix potential memory leak in atomic_pool_init()

Merge tag 'gpio-fixes-v3.6' of git://git./linux/kernel/git/linusw/linux-gpio

Pull GPIO fix from Linus Walleij:
 "A late GPIO fix: Roland Stigge found a problem in the LPC32xx driver
  where a callback ignores one of its arguments.  It needs to go into
  stable too so sending this upstream immediately."

* tag 'gpio-fixes-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio-lpc32xx: Fix value handling of gpio_direction_output()

Merge tag 'md-3.6-fixes' of git://neil.brown.name/md

Pull two md bugfixes from NeilBrown:
 "One (missing spinlock init) was only introduced recently.  The other
  has been present as long as raid10 has been supported, so is tagged
  for -stable."

* tag 'md-3.6-fixes' of git://neil.brown.name/md:
  md/raid10: fix "enough" function for detecting if array is failed.
  md/raid5: add missing spin_lock_init.

Merge git://git./linux/kernel/git/mchehab/linux-edac

Pull EDAC fixes from Mauro Carvalho Chehab:
 "Three edac fixes at the memory enumeration logic:
        - i3200_edac: Fixes a regression at the memory rank size, when the
                memorias are dual-rank;
        - i5000_edac: Fix a longstanding bug when calculating the memory
                size: before Kernel 3.6, the memory size were right only
                with one specific configuration;
        - sb_edac: Fixes a bug since the initial release of the driver:
                with 16GB DIMMs, there's an overflow at the memory size,
                causing the number of pages per dimm (an unsigned value)
                to have the highest bit equal to 1, effectively mangling
                the memory size.

  The third bug can potentially affect the error decoding logic as well."

* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
  sb_edac: Avoid overflow errors at memory size calculation
  i5000: Fix the memory size calculation with 2R memories
  i3200_edac: Fix memory rank size

trivial select_parent documentation fix

"Search list for X" sounds like you're trying to find X on a list.

Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

net: phy: smsc: Implement PHY config_init for LAN87xx

The LAN8710/LAN8720 chips do have broken the "FlexPWR" smart power-saving
capability. Enabling it leads to the PHY not being able to detect Link when
cold-started without cable connected. Thus, make sure this is disabled.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christian Hohnstaedt <chohnstaedt@innominate.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>

smsc75xx: fix resume after device reset

On some systems this device fails to properly resume after suspend,
this patch fixes it by running the usbnet_resume handler.

I suspect this also fixes this bug:

http://code.google.com/p/chromium-os/issues/detail?id=31871

Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

[media] media: mx2_camera: use managed functions to clean up code

Use managed functions to clean up the error handling code and function
mx2_camera_remove().  Along with the change, a few variables get removed
from struct mx2_camera_dev.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: mx2_camera: remove dead code in mx2_camera_add_device

This is a piece of code becoming dead since commit 2c9ba37 ([media]
V4L: mx2_camera: remove unsupported i.MX27 DMA mode, make EMMA
mandatory).  It should have been removed together with the commit.
Remove it now.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

um: Preinclude include/linux/kern_levels.h

The userspace part of UML uses the asm-offsets.h generator mechanism to
create definitions for UM_KERN_<LEVEL> that match the in-kernel
KERN_<LEVEL> constant definitions.

As of commit 04d2c8c83d0e3ac5f78aeede51babb3236200112 ("printk: convert
the format for KERN_<LEVEL> to a 2 byte pattern"), KERN_<LEVEL> is no
longer expanded to the literal '"<LEVEL>"', but to '"\001" "LEVEL"', i.e.
it contains two parts.

However, the combo of DEFINE_STR() in
arch/x86/um/shared/sysdep/kernel-offsets.h and sed-y in Kbuild doesn't
support string literals consisting of multiple parts. Hence for all
UM_KERN_<LEVEL> definitions, only the SOH character is retained in the actual
definition, while the remainder ends up in the comment. E.g. in
include/generated/asm-offsets.h we get

    #define UM_KERN_INFO "\001" /* "6" KERN_INFO */

instead of

    #define UM_KERN_INFO "\001" "6" /* KERN_INFO */

This causes spurious '^A' output in some kernel messages:

    Calibrating delay loop... 4640.76 BogoMIPS (lpj=23203840)
    pid_max: default: 32768 minimum: 301
    Mount-cache hash table entries: 256
    ^AChecking that host ptys support output SIGIO...Yes
    ^AChecking that host ptys support SIGIO on close...No, enabling workaround
    ^AUsing 2.6 host AIO
    NET: Registered protocol family 16
    bio: create slab <bio-0> at 0
    Switching to clocksource itimer

To fix this:
  - Move the mapping from UM_KERN_<LEVEL> to KERN_<LEVEL> from
    arch/um/include/shared/common-offsets.h to
    arch/um/include/shared/user.h, which is preincluded for all userspace
    parts,
  - Preinclude include/linux/kern_levels.h for all userspace parts, to
    obtain the in-kernel KERN_<LEVEL> constant definitions. This doesn't
    violate the kernel/userspace separation, as include/linux/kern_levels.h
    is self-contained and doesn't expose any other kernel internals.
  - Remove the now unused STR() and DEFINE_STR() macros.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Richard Weinberger <richard@nod.at>

[media] anysee: do not remove CI when it is not attached

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] e4000: fix crash when attach fails

Callbacks were set even attach failed. This leads calling
.release() in error case and resulted crash.

Reported-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] fc2580: fix crash when attach fails

Callbacks were set even attach failed. This leads calling
.release() in error case and resulted crash.

Reported-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: fix error handling for .tuner_attach()

fe was not set NULL after it was destroyed in tuner attach fail
error case. Due to that it was destroyed again and Kernel oopsed.

Reported-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] fc2580: small improvements for chip id check

* better readability
* make checkpatch.pl happy
* few bytes smaller binary footprint

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cypress_firmware: refactor firmware downloading

Refactor firmware download function. It also should fix one bug
coming from usb_control_msg() message buffers. Taking buffers from
the stack for usb_control_msg() is not allowed as it does not work
on all architectures. Allocate buffers using kmalloc().

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cypress_firmware: use Kernel dev_foo() logging

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rtl28xxu: [0413:6680] DigitalNow Quad DVB-T Receiver

It is 4 x RTL2832U + 4 x FC0012 in one PCIe board.
Of course there is a PCIe USB host controller too.
Big thanks for Darryl Bond reporting and testing that!

Reported-by: Darryl Bond <darryl.bond@gmail.com>
Tested-by: Darryl Bond <darryl.bond@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] Support for Asus MyCinema U3100Mini Plus

This is initial support for the Asus MyCinema U3100Mini Plus. The driver
in its current form gets detected and loads properly.
Scanning using dvbscan works without problems, Locking onto a channel
using tzap also works fine. Only playback using tzap -r + mplayer was
tested and was fully functional.
It uses the af9035 USB Bridge chip, with an af9033 demodulator. The tuner
used is the FCI FC2580.

Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rtl28xxu: use proper config for e4000 tuner

Do not abuse anymore fc0012 tuner config.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rtl2832: add configuration for e4000 tuner

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rtl28xxu: remove fc0013 tuner fe callback

It is just stub implementation, remove it.
Also add debug for beginning of fe callback.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rtl28xxu: move rtl2831u tuner probing to .read_config()

Move rtl2831u tuner probing correct place.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rtl28xxu: do not return error for unimplemented fe callback

Use of frontend callback is highly hardware design dependent
and whole callback could be optional in many cases. Returning
error by default when callback is not implemented is stupid.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rtl28xxu: masked reg write

Implement masked register write and use it.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rtl28xxu: move rtl2832u tuner probing to .read_config()

Move rtl2832u tuner probing correct place.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] af9035: declare MODULE_FIRMWARE

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: call streaming_ctrl() before kill urbs

Logically it is better ask hardware to stop streaming before
killing urbs carrying stream. Earlier it was just opposite.
Now code runs:
* submit urbs
* start streaming
** streaming ongoing **
* stop streaming
* kill urbs

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: rename module dvb_usbv2 => dvb_usb_v2

I think it is better name. At that phase renaming is quite painless
as module is not yet merged to mainline Kernel.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

um: Fix IPC on um

commit c1d7e01d (ipc: use Kconfig options for __ARCH_WANT_[COMPAT_]IPC_PARSE_VERSION)
forgot UML and broke IPC on it.
Also UML has to select ARCH_WANT_IPC_PARSE_VERSION usin Kconfig.

Reported-and-tested-by: <Toralf Förster toralf.foerster@gmx.de>
Signed-off-by: Richard Weinberger <richard@nod.at>

[media] cxd2820r: use Kernel GPIO for GPIO access

Currently there is LNA behind cxd2820r demodulator GPIO. Use
Kernel GPIO interface to access those GPIOs.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cxd2820r: switch to Kernel dev_* logging

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] DVB API: LNA documentation

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] add LNA support for DVB API

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_frontend: do not allow statistic IOCTLs when sleeping

Demodulator cannot perform statistic IOCTLs when it is not tuned.
Return -EAGAIN in such case.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

netdev: pasemi: fix return value check in pasemi_mac_phy_init()

In case of error, the function of_phy_connect() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

[media] media-devnode: Replace printk with pr_*

Fixes checkpatch warnings related to printk.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] omap3isp: Fix error return code in probe function

Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
[laurent.pinchart@ideasonboard.com Replaced EBUSY with ENODEV]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

team: fix return value check

In case of error, the function genlmsg_put() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

l2tp: fix return value check

In case of error, the function genlmsg_put() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://1984.lsi.us.es/nf

Pablo Neira Ayuso says:

====================
If time allows, I'd appreciate if you can take the following fix
for the xt_limit match.

As Jan indicates, random things may occur while using the xt_limit
match due to use of uninitialized memory.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

[media] omap3isp: Fix up ENOIOCTLCMD error handling

At commit 07d106d0, Linus pointed out that ENOIOCTLCMD should be
translated as ENOTTY to user mode.

Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

USB: Fix race condition when removing host controllers

This patch (as1607) fixes a race that can occur if a USB host
controller is removed while a process is reading the
/sys/kernel/debug/usb/devices file.

The usb_device_read() routine uses the bus->root_hub pointer to
determine whether or not the root hub is registered.  The is not a
valid test, because the pointer is set before the root hub gets
registered and remains set even after the root hub is unregistered and
deallocated.  As a result, usb_device_read() or usb_device_dump() can
access freed memory, causing an oops.

The patch changes the test to use the hcd->rh_registered flag, which
does get set and cleared at the appropriate times.  It also makes sure
to hold the usb_bus_list_lock mutex while setting the flag, so that
usb_device_read() will become aware of new root hubs as soon as they
are registered.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Don Zickus <dzickus@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: ohci-at91: fix null pointer in ohci_hcd_at91_overcurrent_irq

Fixes the following NULL pointer dereference:
[    7.740000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    7.810000] Unable to handle kernel NULL pointer dereference at virtual address 00000028
[    7.810000] pgd = c3a38000
[    7.810000] [00000028] *pgd=23a8c831, *pte=00000000, *ppte=00000000
[    7.810000] Internal error: Oops: 17 [#1] PREEMPT ARM
[    7.810000] Modules linked in: ohci_hcd(+) regmap_i2c snd_pcm usbcore snd_page_alloc at91_cf snd_timer pcmcia_rsrc snd soundcore gpio_keys regmap_spi pcmcia_core usb_common nls_base
[    7.810000] CPU: 0    Not tainted  (3.6.0-rc6-mpa+ #264)
[    7.810000] PC is at __gpio_to_irq+0x18/0x40
[    7.810000] LR is at ohci_hcd_at91_overcurrent_irq+0x24/0xb4 [ohci_hcd]
[    7.810000] pc : [<c01392d4>]    lr : [<bf08f694>]    psr: 40000093
[    7.810000] sp : c3a11c40  ip : c3a11c50  fp : c3a11c4c
[    7.810000] r10: 00000000  r9 : c02dcd6e  r8 : fefff400
[    7.810000] r7 : 00000000  r6 : c02cc928  r5 : 00000030  r4 : c02dd168
[    7.810000] r3 : c02e7350  r2 : ffffffea  r1 : c02cc928  r0 : 00000000
[    7.810000] Flags: nZcv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment user
[    7.810000] Control: c000717f  Table: 23a38000  DAC: 00000015
[    7.810000] Process modprobe (pid: 285, stack limit = 0xc3a10270)
[    7.810000] Stack: (0xc3a11c40 to 0xc3a12000)
[    7.810000] 1c40: c3a11c6c c3a11c50 bf08f694 c01392cc c3a11c84 c2c38b00 c3806900 00000030
[    7.810000] 1c60: c3a11ca4 c3a11c70 c0051264 bf08f680 c3a11cac c3a11c80 c003e764 c3806900
[    7.810000] 1c80: c2c38b00 c02cb05c c02cb000 fefff400 c3806930 c3a11cf4 c3a11cbc c3a11ca8
[    7.810000] 1ca0: c005142c c005123c c3806900 c3805a00 c3a11cd4 c3a11cc0 c0053f24 c00513e4
[    7.810000] 1cc0: c3a11cf4 00000030 c3a11cec c3a11cd8 c005120c c0053e88 00000000 00000000
[    7.810000] 1ce0: c3a11d1c c3a11cf0 c00124d0 c00511e0 01400000 00000001 00000012 00000000
[    7.810000] 1d00: ffffffff c3a11d94 00000030 00000000 c3a11d34 c3a11d20 c005120c c0012438
[    7.810000] 1d20: c001dac4 00000012 c3a11d4c c3a11d38 c0009b08 c00511e0 c00523fc 60000013
[    7.810000] 1d40: c3a11d5c c3a11d50 c0008510 c0009ab4 c3a11ddc c3a11d60 c0008eb4 c00084f0
[    7.810000] 1d60: 00000000 00000030 00000000 00000080 60000013 bf08f670 c3806900 c2c38b00
[    7.810000] 1d80: 00000030 c3806930 00000000 c3a11ddc c3a11d88 c3a11da8 c0054190 c00523fc
[    7.810000] 1da0: 60000013 ffffffff c3a11dec c3a11db8 00000000 c2c38b00 bf08f670 c3806900
[    7.810000] 1dc0: 00000000 00000080 c02cc928 00000030 c3a11e0c c3a11de0 c0052764 c00520d8
[    7.810000] 1de0: c3a11dfc 00000000 00000000 00000002 bf090f61 00000004 c02cc930 c02cc928
[    7.810000] 1e00: c3a11e4c c3a11e10 bf090978 c005269c bf090f61 c02cc928 bf093000 c02dd170
[    7.810000] 1e20: c3a11e3c c02cc930 c02cc930 bf0911d0 bf0911d0 bf093000 c3a10000 00000000
[    7.810000] 1e40: c3a11e5c c3a11e50 c0155b7c bf090808 c3a11e7c c3a11e60 c0154690 c0155b6c
[    7.810000] 1e60: c02cc930 c02cc964 bf0911d0 c3a11ea0 c3a11e9c c3a11e80 c015484c c01545e8
[    7.810000] 1e80: 00000000 00000000 c01547e4 bf0911d0 c3a11ec4 c3a11ea0 c0152e58 c01547f4
[    7.810000] 1ea0: c381b88c c384ab10 c2c10540 bf0911d0 00000000 c02d7518 c3a11ed4 c3a11ec8
[    7.810000] 1ec0: c01544c0 c0152e0c c3a11efc c3a11ed8 c01536cc c01544b0 bf091075 c3a11ee8
[    7.810000] 1ee0: bf049af0 bf09120c bf0911d0 00000000 c3a11f1c c3a11f00 c0154e9c c0153628
[    7.810000] 1f00: bf049af0 bf09120c 000ae190 00000000 c3a11f2c c3a11f20 c0155f58 c0154e04
[    7.810000] 1f20: c3a11f44 c3a11f30 bf093054 c0155f1c 00000000 00006a4f c3a11f7c c3a11f48
[    7.810000] 1f40: c0008638 bf093010 bf09120c 000ae190 00000000 c00093c4 00006a4f bf09120c
[    7.810000] 1f60: 000ae190 00000000 c00093c4 00000000 c3a11fa4 c3a11f80 c004fdc4 c000859c
[    7.810000] 1f80: c3a11fa4 000ae190 00006a4f 00016eb8 000ad018 00000080 00000000 c3a11fa8
[    7.810000] 1fa0: c0009260 c004fd58 00006a4f 00016eb8 000ae190 00006a4f 000ae100 00000000
[    7.810000] 1fc0: 00006a4f 00016eb8 000ad018 00000080 000adba0 000ad208 00000000 000ad3d8
[    7.810000] 1fe0: beaf7ae8 beaf7ad8 000172b8 b6e4e940 20000010 000ae190 00000000 00000000
[    7.810000] Backtrace:
[    7.810000] [<c01392bc>] (__gpio_to_irq+0x0/0x40) from [<bf08f694>] (ohci_hcd_at91_overcurrent_irq+0x24/0xb4 [ohci_hcd])
[    7.810000] [<bf08f670>] (ohci_hcd_at91_overcurrent_irq+0x0/0xb4 [ohci_hcd]) from [<c0051264>] (handle_irq_event_percpu+0x38/0x1a8)
[    7.810000]  r6:00000030 r5:c3806900 r4:c2c38b00
[    7.810000] [<c005122c>] (handle_irq_event_percpu+0x0/0x1a8) from [<c005142c>] (handle_irq_event+0x58/0x7c)
[    7.810000] [<c00513d4>] (handle_irq_event+0x0/0x7c) from [<c0053f24>] (handle_simple_irq+0xac/0xd8)
[    7.810000]  r5:c3805a00 r4:c3806900
[    7.810000] [<c0053e78>] (handle_simple_irq+0x0/0xd8) from [<c005120c>] (generic_handle_irq+0x3c/0x48)
[    7.810000]  r4:00000030
[    7.810000] [<c00511d0>] (generic_handle_irq+0x0/0x48) from [<c00124d0>] (gpio_irq_handler+0xa8/0xfc)
[    7.810000]  r4:00000000
[    7.810000] [<c0012428>] (gpio_irq_handler+0x0/0xfc) from [<c005120c>] (generic_handle_irq+0x3c/0x48)
[    7.810000] [<c00511d0>] (generic_handle_irq+0x0/0x48) from [<c0009b08>] (handle_IRQ+0x64/0x88)
[    7.810000]  r4:00000012
[    7.810000] [<c0009aa4>] (handle_IRQ+0x0/0x88) from [<c0008510>] (at91_aic_handle_irq+0x30/0x38)
[    7.810000]  r5:60000013 r4:c00523fc
[    7.810000] [<c00084e0>] (at91_aic_handle_irq+0x0/0x38) from [<c0008eb4>] (__irq_svc+0x34/0x60)
[    7.810000] Exception stack(0xc3a11d60 to 0xc3a11da8)
[    7.810000] 1d60: 00000000 00000030 00000000 00000080 60000013 bf08f670 c3806900 c2c38b00
[    7.810000] 1d80: 00000030 c3806930 00000000 c3a11ddc c3a11d88 c3a11da8 c0054190 c00523fc
[    7.810000] 1da0: 60000013 ffffffff
[    7.810000] [<c00520c8>] (__setup_irq+0x0/0x458) from [<c0052764>] (request_threaded_irq+0xd8/0x134)
[    7.810000] [<c005268c>] (request_threaded_irq+0x0/0x134) from [<bf090978>] (ohci_hcd_at91_drv_probe+0x180/0x41c [ohci_hcd])
[    7.810000] [<bf0907f8>] (ohci_hcd_at91_drv_probe+0x0/0x41c [ohci_hcd]) from [<c0155b7c>] (platform_drv_probe+0x20/0x24)
[    7.810000] [<c0155b5c>] (platform_drv_probe+0x0/0x24) from [<c0154690>] (driver_probe_device+0xb8/0x20c)
[    7.810000] [<c01545d8>] (driver_probe_device+0x0/0x20c) from [<c015484c>] (__driver_attach+0x68/0x88)
[    7.810000]  r7:c3a11ea0 r6:bf0911d0 r5:c02cc964 r4:c02cc930
[    7.810000] [<c01547e4>] (__driver_attach+0x0/0x88) from [<c0152e58>] (bus_for_each_dev+0x5c/0x9c)
[    7.810000]  r6:bf0911d0 r5:c01547e4 r4:00000000
[    7.810000] [<c0152dfc>] (bus_for_each_dev+0x0/0x9c) from [<c01544c0>] (driver_attach+0x20/0x28)
[    7.810000]  r7:c02d7518 r6:00000000 r5:bf0911d0 r4:c2c10540
[    7.810000] [<c01544a0>] (driver_attach+0x0/0x28) from [<c01536cc>] (bus_add_driver+0xb4/0x22c)
[    7.810000] [<c0153618>] (bus_add_driver+0x0/0x22c) from [<c0154e9c>] (driver_register+0xa8/0x144)
[    7.810000]  r7:00000000 r6:bf0911d0 r5:bf09120c r4:bf049af0
[    7.810000] [<c0154df4>] (driver_register+0x0/0x144) from [<c0155f58>] (platform_driver_register+0x4c/0x60)
[    7.810000]  r7:00000000 r6:000ae190 r5:bf09120c r4:bf049af0
[    7.810000] [<c0155f0c>] (platform_driver_register+0x0/0x60) from [<bf093054>] (ohci_hcd_mod_init+0x54/0x8c [ohci_hcd])
[    7.810000] [<bf093000>] (ohci_hcd_mod_init+0x0/0x8c [ohci_hcd]) from [<c0008638>] (do_one_initcall+0xac/0x174)
[    7.810000]  r4:00006a4f
[    7.810000] [<c000858c>] (do_one_initcall+0x0/0x174) from [<c004fdc4>] (sys_init_module+0x7c/0x1a0)
[    7.810000] [<c004fd48>] (sys_init_module+0x0/0x1a0) from [<c0009260>] (ret_fast_syscall+0x0/0x2c)
[    7.810000]  r7:00000080 r6:000ad018 r5:00016eb8 r4:00006a4f
[    7.810000] Code: e24cb004 e59f3028 e1a02000 e7930180 (e5903028)
[    7.810000] ---[ end trace 85aa37ed128143b5 ]---
[    7.810000] Kernel panic - not syncing: Fatal exception in interrupt

Commit 6fffb77c (USB: ohci-at91: fix PIO handling in relation with number of
ports) started setting unused pins to EINVAL. But this exposed a bug in the
ohci_hcd_at91_overcurrent_irq function where the gpio was used without being
checked to see if it is valid.

This patches fixed the issue by adding the gpio valid check.

Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Cc: stable <stable@vger.kernel.org> # [3.4+] whereever 6fffb77c went
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

um: kill thread->forking

we only use that to tell copy_thread() done by syscall from that
done by kernel_thread().  However, it's easier to do simply by
checking PF_KTHREAD in thread flags.

Merge sys_clone() guts for 32bit and 64bit, while we are at it...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

um: let signal_delivered() do SIGTRAP on singlestepping into handler

... rather than duplicating that in sigframe setup code (and doing that
inconsistently, at that)

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

um: don't leak floating point state and segment registers on execve()

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>