Merge branch 'misc' into for-linus

[SCSI] hpsa: allow SCSI mid layer to handle unit attention

We were clobbering the SCSI status and setting
cmd->result = DID_SOFT_ERROR << 16; to get a retry,
but better to let the mid layer handle the unit
attention.

Signed-off-by: Matt Gates <matthew.gates@hp.com>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] hpsa: do not require board "not ready" status after hard reset

Immediately following a hard board reset, There are some
mandatory delays during which we must not access the board
and during which we might miss the "not ready" status,
therefore it is a mistake to look for and expect to see
the "not ready" status.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] hpsa: enable unit attention reporting

This used to be the default, but at some point the firmware guys
changed the default and I failed to notice.  Now to get unit
attention notifications, you must twiddle a bit indicating you
want them.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] hpsa: rename scsi prefetch field

The field contains more bits than just the one
to indicate whether scsi prefetch should be turned on.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] hpsa: use workqueue instead of kernel thread for lockup detection

Much simpler and avoids races starting/stopping the thread.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] ipr: increase dump size in ipr driver

To help debugging several new SAS controllers, increase the dump size in ipr
driver to 80MB.

Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] mac_scsi: Fix crash on out of memory

Missing check on scsi_register

Signed-off-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] st: fix enlarge_buffer

This patch removes a bug in enlarge_buffer() that can make a
read or write fail under special conditions.

After changing TRY_DIRECT_IO to 0 and ST_MAX_SG to 32 in
st_options.h, a program that writes a first block of 128k and
than a second bigger block (e.g. 256k) fails. The second write
returns errno EOVERFLOW, as enlarge_buffer() checks the sg list
and detects that it already is full.
As enlarge_buffer uses different page allocation orders
depending on the size of the buffer needed, the check does not
make sense.

Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla1280: Annotate timer on stack so object debug does not complain

Object Debug option in 3.13-rc1 resultsin  the following warning, cure
it by annotating the timer to be on stack. The timer is deleted in the
same function so stack seems OK.

ODEBUG: object is on stack, but not annotated
------------[ cut here ]------------
WARNING: CPU: 6 PID: 18 at lib/debugobjects.c:300 __debug_object_init+0x184/0x240()
Modules linked in:
CPU: 6 PID: 18 Comm: kworker/u4:1 Tainted: G        W    3.13.0-rc1 #16
Workqueue: events_unbound async_run_entry_fn
Call Trace:
[00000000004585cc] warn_slowpath_common+0x4c/0x80
[0000000000458614] warn_slowpath_null+0x14/0x40
[000000000063d524] __debug_object_init+0x184/0x240
[000000000063d5fc] debug_object_init+0x1c/0x40
[00000000004645ec] init_timer_key+0xc/0x60
[00000000006cca60] qla1280_mailbox_command+0xc0/0x2a0
[00000000006ccdd4] qla1280_set_target_parameters+0x194/0x220
[00000000006cd324] qla1280_slave_configure+0x384/0x3c0
[00000000006a5d48] scsi_add_lun+0x5c8/0x640
[00000000006a62b8] scsi_probe_and_add_lun+0x1b8/0x2e0
[00000000006a6c2c] __scsi_scan_target+0x8c/0x100
[00000000006a6cf4] scsi_scan_channel+0x54/0xa0
[00000000006a7008] scsi_scan_host_selected+0xc8/0x120
[00000000006a70e0] do_scsi_scan_host+0x80/0xa0
[00000000006a7164] do_scan_async+0x4/0x20
[00000000004817b8] async_run_entry_fn+0x58/0x120
---[ end trace 9a1420108ebfd590 ]---

Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Update driver version to 5.04.00-k3

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Recreate chap data list during get chap operation

Recreate the chap data list during the get chap operation in
qla4xxx_get_chap_list().

Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Add support for ISCSI_PARAM_LOCAL_IPADDR sysfs attr

Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] libiscsi: Add local_ipaddr parameter in iscsi_conn struct

Add local_ipaddr param and support get/set operations on it.

Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] scsi_transport_iscsi: Export ISCSI_PARAM_LOCAL_IPADDR attr for iscsi_connection

This attribute specifies the local IP address used to establish connection.

Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Add host statistics support

The statistics include MAC, TCP/IP & iSCSI statistics.

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] scsi_transport_iscsi: Add host statistics support

Add transport_iscsi hooks to get aggregate host statistics.
The statistics include MAC, TCP/IP & iSCSI statistics.

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Added support for Diagnostics MBOX command

Added support for Diagnostics MBOX command via BSG Vendor HST_VENDOR
interface.  This command provides various tests for validating hardware
functionality.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] bfa: Driver version upgrade to 3.2.23.0

Patch includes changes to upgrade bfa driver version to 3.2.23.0 and use
firmware version 3.2.3.0

Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] bfa: change FC_ELS_TOV to 20sec

As per the FCP specs, the timeout for issuing ABTS is 20 sec; not 21
sec. Hence setting the TOV to 20 sec.

Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] bfa: Observed auto D-port mode instead of manual

Observed Auto mode in the HBA side while doing manual D-Port test on the
switch side. Mode is not passed to BFA from firmware when the test is
triggered by switch side. BFA just blindly using Auto mode.

Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] bfa: Fix for bcu or hcm faa query hang

This patch set fixes the issue of brocade management utility hang
(bcu/HCM) when faa attributes are queried from multiple application
threads. Hang was due to race between the threads and completion handler
corruption.

Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] bfa: LUN discovery issue in direct attach mode

In direct attach mode, if port features like QoS/Trunk/FEC/CR are
enabled, driver can receive PLOGI from the target before firmware
notifies lport online to the driver. In case the lport is not yet online
and a PLOGI is received, send a reject to the peer port, instead of
dropping it on the floor.

Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] bfa: Register port with SCSI even on port init failure

This patch addresses the issue of port not being registered with SCSI
layer on bfa or firmware initialization failure and subsequently failure
in collecting driver traces for debugging port init failures. Also it
has minor changes related to bfad state machine clean up.

Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] bfa: Firmware patch simplification

This patch includes change to enable firmware patch simplication
feature. This feature is targeted to address the requirement to have
independent patch release for firmware. Prior to 3.2.3, releasing a
patch fix for firmware requires changes to bfa, to use new firmware
images. But with these changes, if the new firmware is flashed on to the
HBA with brocade adapter management utilites, driver uses the new
firmware after checking the patch release byte in the firmware version.

Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] be2iscsi: fix memory leak in error path

There are two memory leaks in cases 'ISCSI_NET_PARAM_VLAN_ID' and
'ISCSI_NET_PARAM_VLAN_PRIORITY' and also a potential junk pointer free if
mgmt_get_if_info() returns error because if_info will be unset and it is stack
allocated.

Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Cc: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] ipr: Increase msi-x interrupt vectors to 16

Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] hpsa: remove P822se PCI ID

Remove PCI ID for the never shipped P822se.

Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Fix warning reported by smatch.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] sd: Do not call do_div() with a 64-bit divisor

do_div() is meant for divisions of 64-bit number by 32-bit numbers.
Passing 64-bit divisor types caused issues in the past on 32-bit platforms,
cfr. commit ea077b1b96e073eac5c3c5590529e964767fc5f7 ("m68k: Truncate base
in do_div()").

As scsi_device.sector_size is unsigned (int), factor should be unsigned
int, too.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc: Fix wrong assignment in lpfc_debugfs.c

On lpfc_debugfs_initialize function the dumpHostSlim member setup happens
when 'phba->sli_rev < LPFC_SLI_REV4' is true, however when it is false NULL
has been assigned to debug_dumpHBASlim instead of debug_dumpHostSlim.

Signed-off-by: Felipe Pena <felipensp@gmail.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] megaraid: Use resource_size_t for PCI resources, not long

The assumption that sizeof(long) >= sizeof(resource_size_t) can lead to
truncation of the PCI resource address, meaning this driver didn't work
on 32-bit systems with 64-bit PCI adressing ranges.

Signed-off-by: Ben Collins <ben.c@servergy.com>
Acked-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] Update documentation

The documentation has gone out-of-sync, so update it to
the current status.

Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] Set the minimum valid value of 'eh_deadline' as 0

The former minimum valid value of 'eh_deadline' is 1s, which means
the earliest occasion to shorten EH is 1 second later since a
command is failed or timed out. But if we want to skip EH steps
ASAP, we have to wait until the first EH step is finished. If the
duration of the first EH step is long, this waiting time is
excruciating. So, it is necessary to accept 0 as the minimum valid
value for 'eh_deadline'.

According to my test, with Hannes' patchset 'New EH command timeout
handler' as well, the minimum IO time is improved from 73s
(eh_deadline = 1) to 43s(eh_deadline = 0) when commands are timed
out by disabling RSCN and target port.

Signed-off-by: Ren Mingxin <renmx@cn.fujitsu.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] Unlock accesses to eh_deadline

32bit accesses are guaranteed to be atomic, so we can remove
the spinlock when checking for eh_deadline. We only need to
make sure to catch any updates which might happened during
the call to time_before(); if so we just recheck with the
correct value.

Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] improved eh timeout handler

When a command runs into a timeout we need to send an 'ABORT TASK'
TMF. This is typically done by the 'eh_abort_handler' LLDD callback.

Conceptually, however, this function is a normal SCSI command, so
there is no need to enter the error handler.

This patch implements a new scsi_abort_command() function which
invokes an asynchronous function scsi_eh_abort_handler() to
abort the commands via the usual 'eh_abort_handler'.

If abort succeeds the command is either retried or terminated,
depending on the number of allowed retries. However, 'eh_eflags'
records the abort, so if the retry would fail again the
command is pushed onto the error handler without trying to
abort it (again); it'll be cleared up from SCSI EH.

[hare: smatch detected stray switch fixed]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] Fix erratic device offline during EH

Commit 18a4d0a22ed6c54b67af7718c305cd010f09ddf8
(Handle disk devices which can not process medium access commands)
was introduced to offline any device which cannot process medium
access commands.
However, commit 3eef6257de48ff84a5d98ca533685df8a3beaeb8
(Reduce error recovery time by reducing use of TURs) reduced
the number of TURs by sending it only on the first failing
command, which might or might not be a medium access command.
So in combination this results in an erratic device offlining
during EH; if the command where the TUR was sent upon happens
to be a medium access command the device will be set offline,
if not everything proceeds as normal.

This patch moves the check to the final test, eliminating
this problem.

Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] aci7xxx_old: delete decade+ obsolete driver

After getting warnings in an allyesconfig build[1] from this
driver, I decided to remind myself just how old it was, and
whether it warranted fixing.  In the Kconfig help text, I found:

  "This driver will eventually be phased out entirely"

Going back to the history archive, I see the line was added[2]
in Feb 2002, when we moved from v2.4.2.1 ---> v2.4.2.2

So, with over a decade of notification, and multiple major releases
since then, I think we can justify removing this.  Currently we have
people wasting time building it during routine testing, and then
wasting more time re-researching the known reported warnings, only to
find that nobody really is willing to integrate the fixes[3] for it.

A quick search didn't seem to indicate any active user base for it.
If someone happens to have a quirky _old_ card that the eleven year
old "new" driver doesn't work with, then it is entirely reasonable
that they stick with a kernel version that predates this removal.

[1] drivers/scsi/aic7xxx_old.c: In function ‘aic7xxx_register’:
    drivers/scsi/aic7xxx_old.c:7901:5: warning: case value ‘257’ not in enumerated type ‘ahc_chip’ [-Wswitch]
    drivers/scsi/aic7xxx_old.c:7898:5: warning: case value ‘513’ not in enumerated type ‘ahc_chip’ [-Wswitch]
    drivers/scsi/aic7xxx_old.c: In function ‘aic7xxx_load_seeprom’:
    drivers/scsi/aic7xxx_old.c:8517:5: warning: case value ‘257’ not in enumerated type ‘ahc_chip’ [-Wswitch]
    drivers/scsi/aic7xxx_old.c:8510:5: warning: case value ‘513’ not in enumerated type ‘ahc_chip’ [-Wswitch]

[2] http://git.kernel.org/cgit/linux/kernel/git/tglx/history.git commit 44e8778c

[3] https://lkml.org/lkml/2012/10/29/215

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Acked-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] MAINTAINERS: update sg entry

update sg MAINTAINERS file entry: web site and documentation
entry

Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Update the driver version to 8.06.00.12-k.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Adding MAINTAINERS for qla2xxx FC-SCSI driver

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Replace a constant with a macro definition for host->canqueue assigmnment.

Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Reset nic_core_reset_owner on moving from COLD to READY for ISP8044

Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Only complete dcbx_comp and lb_portup_comp for virtual port index 0.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Use scnprintf() instead of snprintf() in the sysfs handlers.

Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Use the correct mailbox registers when acknowledging an IDC request on ISP8044.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add changes to obtain ISPFX00 adapters product information in accordance with firmware update.

Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add logic to abort BSG commands for ISPFX00.

Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Clear RISC INT reg only for an event and not always while polling.

Signed-off-by: Atul Deshmukh <atul.deshmukh@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Fix undefined behavior in call to snprintf().

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add BSG interface for read/write serdes register.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Fix issue with not displaying node name after system reboot.

Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Disable adapter when we encounter a PCI disconnect.

If we become disconnected from the PCI bus/PCIe fabric, there can be long delays
in register reads which can cause erroneous decisions to be made and cause a
soft lockup if a lock is held too long. As a preventative measure, check for a
disconnection (register reads that return -1) and then disable the board if we
find ourselves in this condition. For now, check in our interrupt handlers and
the per adapter one second timer.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Refactor shutdown code so some functionality can be reused.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] Revert "qla2xxx: Ramp down queue depth for attached SCSI devices when driver resources are low."

This reverts commit 3c290d0b5f8ff7b0fd2c964c5ec2c14191a9e790

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Don't consider the drivers knocked out of IDC participation for future reset recovery process.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add BPM support for ISP25xx.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Correctly set mailboxes for extended init control block.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Disable INTx interrupt for ISP82XX

Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Honor execute firmware failures.

If the execute firmware command fails we do not stop the rest of the
initialization process which will continue to fail so if we encounter an error
simply short circuit the process.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Print proper QLAFX00 product name at probe.

Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] hpsa: prevent stalled i/o

If a fifo full condition is encountered, i/o requests will stack
up in the h->reqQ queue.  The only thing which empties this queue
is start_io, which only gets called when new i/o requests come in.
If none are forthcoming, i/o in h->reqQ will be stalled.

To fix this, whenever fifo full condition is encountered, this
is recorded, and the interrupt handler examines this to see
if a fifo full condition was recently encountered when a
command completes and will call start_io to prevent i/o's in
h->reqQ from getting stuck.

I've only ever seen this problem occur when running specialized
test programs that pound on the the CCISS_PASSTHRU ioctl.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] hpsa: cap CCISS_PASSTHRU at 20 concurrent commands.

Cap CCISS_BIG_PASSTHRU as well.  If an attempt is made
to exceed this, ioctl() will return -1 with errno == EAGAIN.

This is to prevent a userland program from exhausting all of
pci_alloc_consistent memory.  I've only seen this problem when
running a special test program designed to provoke it.  20
concurrent commands via the passthru ioctls (not counting SG_IO)
should be more than enough.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] bfa: Chinook quad port 16G FC HBA claim issue

Bfa driver crash is observed while pushing the firmware on to chinook
quad port card due to uninitialized bfi_image_ct2 access which gets
initialized only for CT2 ASIC based cards after request_firmware().
For quard port chinook (CT2 ASIC based), bfi_image_ct2 is not getting
initialized as there is no check for chinook PCI device ID before
request_firmware and instead bfi_image_cb is initialized as it is the
default case for card type check.

This patch includes changes to read the right firmware for quad port chinook.

Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] hpsa: add MSA 2040 to list of external target devices

Signed-off-by: Scott Teel <scott.teel@hp.com>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] hpsa: fix memory leak in CCISS_BIG_PASSTHRU ioctl

We were leaking a command buffer if a DMA mapping error was
encountered in the CCISS_BIG_PASSTHRU ioctl.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] hpsa: remove unneeded include of seq_file.h

Signed-off-by: Scott Teel <scott.teel@hp.com>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] hpsa: add 5 second delay after doorbell reset

The hardware guys tell us that after initiating a software
reset via the doorbell register we need to wait 5 seconds before
attempting to talk to the board *at all*.  This means that we
cannot watch the board to verify it transitions from "ready" to
to "not ready" then back "ready", since this transition will
most likely happen during those 5 seconds (though we can still
verify the reset happens by watching the "driver version" field
get cleared.)

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] hpsa: do not attempt to flush the cache on locked up controllers

There's no point in trying since it can't work, and if you do
try, it will just hang the system on shutdown.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] sr: use block layer runtime PM

Migrate sr to make use of block layer runtime PM. Accordingly, the
SCSI bus layer runtime PM callback is simplified as all SCSI drivers
implementing runtime PM now use the block layer's request-based
mechanism.

Note that due to the device will be polled by kernel at a constant
interval, if the autosuspend delay is set longer than the polling
interval then the device will never suspend.

Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: overflow in qla4xxx_set_chap_entry()

We should cap the size of memcpy() because it comes from the network
and can't be trusted.

Fixes: 26ffd7b45fe9 ('[SCSI] qla4xxx: Add support to set CHAP entries')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Update driver version to 5.04.00-k2

Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Add support for additional network parameters settings

Added support to display and update additional network parameters
through iscsiadm.

Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] iscsi_transport: Additional parameters for network settings

Added support to display and update additional network parameters
through iscsiadm.

Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] iscsi_transport: Remove net param enum values

Remove explicit values assignment for net param enums.

Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] scsi_debug: simplify creation and destruction of driver attribute files

Instead of repeatedly calling driver_create_file() to create driver
attribute files, This achieves the same thing by constructing an array
of driver_attribute and setting it to bus_type->drv_groups.

This change simplifies both creation and destruction of the attribute
files, and also removes sparse warning caused by driver_attributes which
are unnecessarily declared as global.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Linux 3.13-rc4

null_blk: mem garbage on NUMA systems during init

For NUMA systems, initializing the blk-mq layer and using per node hctx.
We initialize submit queues to 1, while blk-mq nr_hw_queues is
initialized to the number of NUMA nodes.

This makes the null_init_hctx function overwrite memory outside of what
it allocated.  In my case it lead to writing garbage into struct
request_queue's mq_map.

Signed-off-by: Matias Bjorling <m@bjorling.me>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

radeon_pm: fix oops in hwmon_attributes_visible() and radeon_hwmon_show_temp_thresh()

Since commit ec39f64bba34 ("drm/radeon/dpm: Convert to use
devm_hwmon_register_with_groups") radeon_hwmon_init() is using
hwmon_device_register_with_groups(), which sets `rdev' as a device
private driver_data, while hwmon_attributes_visible() and
radeon_hwmon_show_temp_thresh() are still waiting for `drm_device'.

Fix them by using dev_get_drvdata(), in order to avoid this oops:

  BUG: unable to handle kernel paging request at 0000000000001e28
  IP: [<ffffffffa02ae8b4>] hwmon_attributes_visible+0x18/0x3d [radeon]
  PGD 15057e067 PUD 151a8e067 PMD 0
  Oops: 0000 [#1] PREEMPT SMP
  Call Trace:
    internal_create_group+0x114/0x1d9
    sysfs_create_group+0xe/0x10
    sysfs_create_groups+0x22/0x5f
    device_add+0x34f/0x501
    device_register+0x15/0x18
    hwmon_device_register_with_groups+0xb5/0xed
    radeon_hwmon_init+0x56/0x7c [radeon]
    radeon_pm_init+0x134/0x7e5 [radeon]
    radeon_modeset_init+0x75f/0x8ed [radeon]
    radeon_driver_load_kms+0xc6/0x187 [radeon]
    drm_dev_register+0xf9/0x1b4 [drm]
    drm_get_pci_dev+0x98/0x129 [drm]
    radeon_pci_probe+0xa3/0xac [radeon]
    pci_device_probe+0x6e/0xcf
    driver_probe_device+0x98/0x1c4
    __driver_attach+0x5c/0x7e
    bus_for_each_dev+0x7b/0x85
    driver_attach+0x19/0x1b
    bus_add_driver+0x104/0x1ce
    driver_register+0x89/0xc5
    __pci_register_driver+0x58/0x5b
    drm_pci_init+0x86/0xea [drm]
    radeon_init+0x97/0x1000 [radeon]
    do_one_initcall+0x7f/0x117
    load_module+0x1583/0x1bb4
    SyS_init_module+0xa0/0xaf

Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Alexander Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge git://git./linux/kernel/git/davem/net

Pull networking fixes from David Miller:

 1) Revert CHECKSUM_COMPLETE optimization in pskb_trim_rcsum(), I can't
    figure out why it breaks things.

 2) Fix comparison in netfilter ipset's hash_netnet4_data_equal(), it
    was basically doing "x == x", from Dave Jones.

 3) Freescale FEC driver was DMA mapping the wrong number of bytes, from
    Sebastian Siewior.

 4) Blackhole and prohibit routes in ipv6 were not doing the right thing
    because their ->input and ->output methods were not being assigned
    correctly.  Now they behave properly like their ipv4 counterparts.
    From Kamala R.

 5) Several drivers advertise the NETIF_F_FRAGLIST capability, but
    really do not support this feature and will send garbage packets if
    fed fraglist SKBs.  From Eric Dumazet.

 6) Fix long standing user triggerable BUG_ON over loopback in RDS
    protocol stack, from Venkat Venkatsubra.

 7) Several not so common code paths can potentially try to invoke
    packet scheduler actions that might be NULL without checking.  Shore
    things up by either 1) defining a method as mandatory and erroring
    on registration if that method is NULL 2) defininig a method as
    optional and the registration function hooks up a default
    implementation when NULL is seen.  From Jamal Hadi Salim.

 8) Fix fragment detection in xen-natback driver, from Paul Durrant.

 9) Kill dangling enter_memory_pressure method in cg_proto ops, from
    Eric W Biederman.

10) SKBs that traverse namespaces should have their local_df cleared,
    from Hannes Frederic Sowa.

11) IOCB file position is not being updated by macvtap_aio_read() and
    tun_chr_aio_read().  From Zhi Yong Wu.

12) Don't free virtio_net netdev before releasing all of the NAPI
    instances.  From Andrey Vagin.

13) Procfs entry leak in xt_hashlimit, from Sergey Popovich.

14) IPv6 routes that are no cached routes should not count against the
    garbage collection limits.  We had this almost right, but were
    missing handling addrconf generated routes properly.  From Hannes
    Frederic Sowa.

15) fib{4,6}_rule_suppress() have to consider potentially seeing NULL
    route info when they are called, from Stefan Tomanek.

16) TUN and MACVTAP have had truncated packet signalling for some time,
    fix from Jason Wang.

17) Fix use after frrr in __udp4_lib_rcv(), from Eric Dumazet.

18) xen-netback does not interpret the NAPI budget properly for TX work,
    fix from Paul Durrant.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
  igb: Fix for issue where values could be too high for udelay function.
  i40e: fix null dereference
  xen-netback: fix gso_prefix check
  net: make neigh_priv_len in struct net_device 16bit instead of 8bit
  drivers: net: cpsw: fix for cpsw crash when build as modules
  xen-netback: napi: don't prematurely request a tx event
  xen-netback: napi: fix abuse of budget
  sch_tbf: use do_div() for 64-bit divide
  udp: ipv4: must add synchronization in udp_sk_rx_dst_set()
  net:fec: remove duplicate lines in comment about errata ERR006358
  Revert "8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature"
  8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature
  xen-netback: make sure skb linear area covers checksum field
  net: smc91x: Fix device tree based configuration so it's usable
  udp: ipv4: fix potential use after free in udp_v4_early_demux()
  macvtap: signal truncated packets
  tun: unbreak truncated packet signalling
  net: sched: htb: fix the calculation of quantum
  net: sched: tbf: fix the calculation of max_size
  micrel: add support for KSZ8041RNLI
  ...

Merge branch 'x86/urgent' of git://git./linux/kernel/git/tip/tip

Pull x86 fixes from Peter Anvin:
 "This is a pretty small batch:

  The biggest single change is to stop using EFI time services on 32-bit
  platforms.  This matches our current behavior on 64-bit platforms as
  we already had ruled them out there as being too unreliable.  Turns
  out that affects 32-bit platforms, too.

  One NULL pointer fix for SGI UV.

  Two minor build fixes, one of which only affects icc and the other
  which affects icc and future versions or nonstandard default settings
  of gcc"

* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, efi: Don't use (U)EFI time services on 32 bit
  x86, build, icc: Remove uninitialized_var() from compiler-intel.h
  x86/UV: Fix NULL pointer dereference in uv_flush_tlb_others() if the 'nobau' boot option is used
  x86, build: Pass in additional -mno-mmx, -mno-sse options

Merge tag 'pci-v3.13-fixes-2' of git://git./linux/kernel/git/helgaas/pci

Pull PCI updates from Bjorn Helgaas:
 "PCI device hotplug
    - Move device_del() from pci_stop_dev() to pci_destroy_dev() (Rafael
      Wysocki)

  Host bridge drivers
    - Update maintainers for DesignWare, i.MX6, Armada, R-Car (Bjorn
      Helgaas)
    - mvebu: Return 'unsupported' for Interrupt Line and Interrupt Pin
      (Jason Gunthorpe)

  Miscellaneous
    - Avoid unnecessary CPU switch when calling .probe() (Alexander
      Duyck)
    - Revert "workqueue: allow work_on_cpu() to be called recursively"
      (Bjorn Helgaas)
    - Disable Bus Master only on kexec reboot (Khalid Aziz)
    - Omit PCI ID macro strings to shorten quirk names for LTO (Michal
      Marek)"

* tag 'pci-v3.13-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  MAINTAINERS: Add DesignWare, i.MX6, Armada, R-Car PCI host maintainers
  PCI: Disable Bus Master only on kexec reboot
  PCI: mvebu: Return 'unsupported' for Interrupt Line and Interrupt Pin
  PCI: Omit PCI ID macro strings to shorten quirk names
  PCI: Move device_del() from pci_stop_dev() to pci_destroy_dev()
  Revert "workqueue: allow work_on_cpu() to be called recursively"
  PCI: Avoid unnecessary CPU switch when calling driver .probe() method

Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/linux-security

Pull SELinux fixes from James Morris.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  selinux: process labeled IPsec TCP SYN-ACK packets properly in selinux_ip_postroute()
  selinux: look for IPsec labels on both inbound and outbound packets
  selinux: handle TCP SYN-ACK packets correctly in selinux_ip_postroute()
  selinux: handle TCP SYN-ACK packets correctly in selinux_ip_output()
  selinux: fix possible memory leak

Revert "selinux: consider filesystem subtype in policies"

This reverts commit 102aefdda4d8275ce7d7100bc16c88c74272b260.

Tom London reports that it causes sync() to hang on Fedora rawhide:

  https://bugzilla.redhat.com/show_bug.cgi?id=1033965

and Josh Boyer bisected it down to this commit.  Reverting the commit in
the rawhide kernel fixes the problem.

Eric Paris root-caused it to incorrect subtype matching in that commit
breaking fuse, and has a tentative patch, but by now we're better off
retrying this in 3.14 rather than playing with it any more.

Reported-by: Tom London <selinux@gmail.com>
Bisected-by: Josh Boyer <jwboyer@fedoraproject.org>
Acked-by: Eric Paris <eparis@redhat.com>
Cc: James Morris <jmorris@namei.org>
Cc: Anand Avati <avati@redhat.com>
Cc: Paul Moore <paul@paul-moore.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

igb: Fix for issue where values could be too high for udelay function.

This patch changes the igb_phy_has_link function to check the value of the
parameter before deciding to use udelay or mdelay in order to be sure that
the value is not too high for udelay function.

CC: stable kernel <stable@vger.kernel.org> # 3.9+
Signed-off-by: Sunil K Pandey <sunil.k.pandey@intel.com>
Signed-off-by: Kevin B Smith <kevin.b.smith@intel.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

i40e: fix null dereference

If the vsi->tx_rings structure is NULL we don't want to panic.

Change-Id: Ic694f043701738c434e8ebe0caf0673f4410dc10
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'edac_fixes_for_3.13' of git://git./linux/kernel/git/bp/bp

Pull EDAC fix from Borislav Petkov:
 "Silence a compiler warning in sb_edac"

* tag 'edac_fixes_for_3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
  sb_edac: Shut up compiler warning when EDAC_DEBUG is enabled

Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm

Pull ARM fixes from Russell King:
 "This resolves some further issues with the dma mask changes on ARM
  which have been found by TI and others, and also some corner cases
  with the updates to the virtual to physical address translations.

  Konstantin also found some problems with the unwinder, which now
  performs tighter verification that the stack is valid while unwinding"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: fix asm/memory.h build error
  ARM: 7917/1: cacheflush: correctly limit range of memory region being flushed
  ARM: 7913/1: fix framepointer check in unwind_frame
  ARM: 7912/1: check stack pointer in get_wchan
  ARM: 7909/1: mm: Call setup_dma_zone() post early_paging_init()
  ARM: 7908/1: mm: Fix the arm_dma_limit calculation
  ARM: another fix for the DMA mapping checks

Merge tag 'arc-fixes-for-3.13' of git://git./linux/kernel/git/vgupta/arc

Pull ARC fixes from Vineet Gupta:
 "These are couple of weeks old already, but I just couldn't get them to
  you earlier.

   - couple of fixes for recently added perf code
   - build time extable sort"

* tag 'arc-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: [perf] Fix a few thinkos
  ARC: Add guard macro to uapi/asm/unistd.h
  ARC: extable: Enable sorting at build time

Merge tag 'dm-3.13-fixes' of git://git./linux/kernel/git/device-mapper/linux-dm

Pull device mapper fixes from Mike Snitzer:
 "A set of device-mapper fixes for 3.13.

  A fix for possible memory corruption during DM table load, fix a
  possible leak of snapshot space in case of a crash, fix a possible
  deadlock due to a shared workqueue in the delay target, fix to
  initialize read-only module parameters that are used to export metrics
  for dm stats and dm bufio.

  Quite a few stable fixes were identified for both the thin-
  provisioning and caching targets as a result of increased regression
  testing using the device-mapper-test-suite (dmts).  The most notable
  of these are the reference counting fixes for the space map btree that
  is used by the dm-array interface -- without these the dm-cache
  metadata will leak, resulting in dm-cache devices running out of
  metadata blocks.  Also, some important fixes related to the
  thin-provisioning target's transition to read-only mode on error"

* tag 'dm-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm array: fix a reference counting bug in shadow_ablock
  dm space map: disallow decrementing a reference count below zero
  dm stats: initialize read-only module parameter
  dm bufio: initialize read-only module parameters
  dm cache: actually resize cache
  dm cache: update Documentation for invalidate_cblocks's range syntax
  dm cache policy mq: fix promotions to occur as expected
  dm thin: allow pool in read-only mode to transition to read-write mode
  dm thin: re-establish read-only state when switching to fail mode
  dm thin: always fallback the pool mode if commit fails
  dm thin: switch to read-only mode if metadata space is exhausted
  dm thin: switch to read only mode if a mapping insert fails
  dm space map metadata: return on failure in sm_metadata_new_block
  dm table: fail dm_table_create on dm_round_up overflow
  dm snapshot: avoid snapshot space leak on crash
  dm delay: fix a possible deadlock due to shared workqueue

Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid

Pull HID fixes from Jiri Kosina:

 - Genius Gx Imperator Keyboard regression fix (missing break in case),
   by Ben Hutchings

 - duplicate sysfs entry error fix for hid-sensor-hub driver, by
   Srinivas Pandruvada

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: hid-sensor-hub: fix duplicate sysfs entry error
  HID: kye: Fix missing break in kye_report_fixup()

ARM: fix asm/memory.h build error

Jason Gunthorpe reports a build failure when ARM_PATCH_PHYS_VIRT is
not defined:

In file included from arch/arm/include/asm/page.h:163:0,
                 from include/linux/mm_types.h:16,
                 from include/linux/sched.h:24,
                 from arch/arm/kernel/asm-offsets.c:13:
arch/arm/include/asm/memory.h: In function '__virt_to_phys':
arch/arm/include/asm/memory.h:244:40: error: 'PHYS_OFFSET' undeclared (first use in this function)
arch/arm/include/asm/memory.h:244:40: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/include/asm/memory.h: In function '__phys_to_virt':
arch/arm/include/asm/memory.h:249:13: error: 'PHYS_OFFSET' undeclared (first use in this function)

Fixes: ca5a45c06cd4 ("ARM: mm: use phys_addr_t appropriately in p2v and v2p conversions")
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Merge tag 'regulator-v3.13-rc3' of git://git./linux/kernel/git/broonie/regulator

Pull regulator fixes from Mark Brown:
 "A small set of driver fixes plus one larger core change which changes
  the way we check to see if we're using DT so that there aren't any
  races between deciding we're using DT and the regulator subsystem
  noticing.

  This makes the new support for substituting a dummy regulator and
  optional regulators work a lot better on DT systems since it ensures
  that we don't trigger probe deferral when we shouldn't which was
  causing bugs in clients"

* tag 'regulator-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: pfuze100: allow misprogrammed ID
  regulator: pfuze100: Fix address of FABID
  regulator: as3722: set the correct current limit
  regulator: core: Check for DT every time we check full constraints
  regulator: core: Replace checks of have_full_constraints with a function

Merge tag 'regmap-v3.13-rc3' of git://git./linux/kernel/git/broonie/regmap

Pull regmap fixes from Mark Brown:
 "Two small changes to fix some error handling and checking (both of
  which would be quite serious if the errors trigger) plus a trivial
  documentation fix"

* tag 'regmap-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: use IS_ERR() to check clk_get() results
  regmap: make sure we unlock on failure in regmap_bulk_write
  regmap: trivial comment fix (copy'n'paste error)

Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux

Pull i2c fixes from Wolfram Sang:
 "Here are two simple but wanted fixes for the i2c subsystem"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: imx: Check the return value from clk_prepare_enable()
  i2c: mux: Inherit retry count and timeout from parent for muxed bus

Merge tag 'for-linus-20131212' of git://git.infradead.org/linux-mtd

Pull MTD fixes from Brian Norris:
 "Two MTD fixes, for the pxa3xx-nand driver:

   - This driver was not ready to fully Armada 370 NAND, with
     particularly notable problems seen on flash with 2KB page sizes.
     This "compatible" entry really should have been held back until
     3.14 or later.

   - Fix a bug seen in rare cases on the error path of a failed probe
     attempt, where we free unallocated DMA resources"

* tag 'for-linus-20131212' of git://git.infradead.org/linux-mtd:
  mtd: nand: pxa3xx: Use info->use_dma to release DMA resources
  Partially revert "mtd: nand: pxa3xx: Introduce 'marvell,armada370-nand' compatible string"

Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma

Pull slave-dmaengine fixes from Vinod Koul:
 "Here is the common fixes PULL for dmaengine.

  Dan has been working on fixing the build issues in bunch of drivers.
  Here we have one fixing s3c24xx-dma, along with fix from Russell on
  pl08x.  Also we have Kuninori rcar dma fixes.  The s3c24xx-dma which
  was added in last merge window missed updates to usage of DMA_COMPLETE
  so converting the last driver"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dma: fix build breakage in s3c24xx-dma
  Fix pl08x warnings
  rcar-hpbdma: initialise plane information when halted
  rcar-hpbdma: fixup channel busy check for double plane
  rcar-hpbdma: add max transfer size
  dma: mmp_pdma: add missing platform_set_drvdata() in mmp_pdma_probe()
  dmaengine: s3c24xx-dma: use DMA_COMPLETE for dma completion status

dm array: fix a reference counting bug in shadow_ablock

An old array block could have its reference count decremented below
zero when it is being replaced in the btree by a new array block.

The fix is to increment the old ablock's reference count just before
inserting a new ablock into the btree.

Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.9+

dm space map: disallow decrementing a reference count below zero

The old behaviour, returning -EINVAL if a ref_count of 0 would be
decremented, was removed in commit f722063 ("dm space map: optimise
sm_ll_dec and sm_ll_inc").  To fix this regression we return an error
code from the mutator function pointer passed to sm_ll_mutate() and have
dec_ref_count() return -EINVAL if the old ref_count is 0.

Add a DMERR to reflect the potential seriousness of this error.

Also, add missing dm_tm_unlock() to sm_ll_mutate()'s error path.

With this fix the following dmts regression test now passes:
 dmtest run --suite cache -n /metadata_use_kernel/

The next patch fixes the higher-level dm-array code that exposed this
regression.

Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.12+

Merge remote-tracking branch 'regulator/topic/constraints' into regulator-linus