[MMC] sdhci: check controller version

Check the interface version of the controller and bail out if it's an unknown
version.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[MMC] sdhci: check only relevant inhibit bits

Conform to the sdhci specification as to which inhibit bits should be checked
at different times.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[MMC] sdhci: Test for invalid block size

The controller has an upper limit on the block size. Make sure we do not
cross it.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[MMC] sdhci: Avoid sdhci DMA boundaries

The sdhci controllers will issue an interrupt when a configurable number of
bytes have been transfered using DMA. The purpose is to handle multiple,
scattered memory pages.

Unfortunately, it requires that all transfers are completely aligned to
memory pages, which we cannot guarantee. So we just disable the function.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[MMC] Fix sdhci PIO routines

The sdhci controllers operate with blocks, not bytes. The PIO routines must
therefore make sure that the minimum unit transfered is a complete block.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[MMC] sdhci: fix interrupt handling

The specification says that interrupts should be cleared before the source is
removed.  We should also not set unknown bits.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[MMC] sdhci: correct register order

The sdhci specification states that some registers must be written to in a
specific order.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[MMC] sdhci: proper timeout handling

Use the give timeout clock and calculate a proper timeout instead of using the
maximum at all times.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[MMC] sdhci: fix sdhci reset timeout

The reset register is automatically cleared when the reset has completed.
Hence, we should busy wait and not have a fixed delay.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[MMC] sdhci: fix timeout loops in sdhci

The current timeout loop assume that jiffies are updated.  This might not be
the case depending on locks and if the kernel is compiled without preemption.
Change the system to use a counter and fixed delays.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[MMC] sdhci: support for multiple voltages

The sdhci controllers can support up to three voltage levels.  Detect which
and report back to the MMC layer.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[MMC] sdhci: print device id

As sdhci is a generic driver, it is helpful to see some more specific
identification of the actual hardware in dmesg.  PCI vendor, device and
revision is sufficient in most cases.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[MMC] sdhci: check SDHCI base clock

A base clock value of 0 means that the driver must get the base clock through
some other means.  As we have no other way of getting it, we must abort.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] powermac: Fix some 64b resource damage

The 64 bits resource patches did a bit of damage on PowerMac causing a
buffer overflow in macio_asic and a warning in a sound driver. The
former is fixed by reverting the sprintf of the bus_id to %08x as it was
before. The bus_id used for macio devices is always a 32 bits value
(macio always sits in 32 bits space) and since it's exposed to userland,
the format of the string shouldn't be changed like that anyway. The
second by using the proper type for printk.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Merge branch 'audit.b22' of git://git./linux/kernel/git/viro/audit-current

* 'audit.b22' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
  [PATCH] audit syscall classes
  [PATCH] audit: support for object context filters
  [PATCH] audit: rename AUDIT_SE_* constants
  [PATCH] add rule filterkey

Merge git://git./linux/kernel/git/sam/kbuild

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
  kbuild: documentation change on allowing checkers besides sparse
  kbuild: warn when a moduled uses a symbol marked UNUSED
  kbuild: fix segv in modpost
  kconfig: enhancing accessibility of lxdialog
  kbuild: fix ia64 breakage after introducing make -rR

[PATCH] pnp: suppress request_irq() warning

Suppress the "setup_irq: irq handler mismatch" coming out of pnp_check_irq():
failures are expected here.

Cc: <stable@kernel.org>
Cc: Santiago Garcia Mantinan <manty@manty.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] drivers/block/nbd.c compile fix

The Network Block Device driver doesn't compile if NDEBUG is defined.

Signed-off-by: Ingo van Lil <inguin@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] kernel-doc: make man/text mode function output same

Make output of function descriptions in text mode match contents of 'man'
mode by adding Name: plus function-short-description ("purpose") and
changing Function: to Synopsis:.

Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] Fix problem with ATAPI DMA on IT8212 in Linux

Missing variable initialisation would mean it would sometimes not put ATAPI
devices into DMA by default.

Signed-off-by: Alan Cox <alan@redhat.com>
Cc: <Jack.Lee@ite.com.tw>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] kernel-doc: consistent text/man mode output

Add a space between data type and struct field name in man-mode
bitfield struct output so that they don't run together.

For text-mode struct output, print the struct 'purpose' or
short description (as done in man-mode output).

For text-mode enum output, print the enum 'purpose' or
short description (as done in man-mode output).

For text-mode typedef output, print the typedef 'purpose' or
short description (as done in man-mode output).

Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] reiserfs: update ctime and mtime on expanding truncate

Reiserfs does not update ctime and mtime on expanding truncate via
truncate().  This patch fixes it.

Signed-off-by: Vladimir Saveliev <vs@namesys.com>
Cc: Hans Reiser <reiser@namesys.com>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Chris Mason <mason@suse.com>
Cc: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] s390: put sys_call_table into .rodata section and write protect it

Put s390's syscall tables into .rodata section and write protect this
section to prevent misuse of it.  Suggested by Arjan van de Ven
<arjan@infradead.org>.

Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] add __[start|end]_rodata sections to asm-generic/sections.h

Add __start_rodata and __end_rodata to sections.h to avoid extern
declarations.  Needed by s390 code (see following patch).

[akpm@osdl.org: update architectures]
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] hotcpu_notifier-fixes

Always use do {} while (0).  Failing to do so can cause subtle compile
failures or bugs.

Cc: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] RTC: class driver for Samsung S3C series SoC

This is a renamed and tested version of the previous S3C24XX RTC class
driver.

The driver has been renamed from the original s3c2410-rtc, which is now too
narrow for the range of devices supported.

The rtc-s3c has been chosen as there is the distinct possibility of this
driver being carried forward into newer Samsung SoC silicon.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] Fix IS_ERR Threshold Value

 o Raise the maximum error number in IS_ERR_VALUE to 4095.
 o Make that number available as a new constant MAX_ERRNO.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] ufs: truncate should allocate block for last byte

This patch fixes buggy behaviour of UFS
in such kind of scenario:
open(, O_TRUNC...)
ftruncate(, 1024)
ftruncate(, 0)

Such a scenario causes ufs_panic and remount read-only.  This happen
because of according to specification UFS should always allocate block for
last byte, and many parts of our implementation rely on this, but
`ufs_truncate' doesn't care about this.

To make possible return error code and to know about old size, this patch
removes `truncate' from ufs inode_operations and uses `setattr' method to
call ufs_truncate.

Signed-off-by: Evgeniy Dushistov <dushistov@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] uml: rename and improve actually_do_remove()

Rename actually_do_remove() to remove_files_and_dir(), make it call
closedir(), make it ignore ENOENT (I see it frequently enough).

ENOENT is probably due to multiple threads calling the exitcall functions
together*, but fixing that is non-trivial; and ignoring it is perfectly ok
in any case.

* it can surely happen: last_ditch_exit() is installed as SIGTERM handler
  at boot, and it's not removed on thread creation.  So killall vmlinux
  (which I do) surely causes that.  I've seen also a crash which seems to
  do the same.

Installing the handler on only the main thread would make UML do no cleanup
when another thread exits, and we're not sure we want that.  And mutual
exclusion in that context is tricky - we can't use spinlock in code not on
a kernel stack (spinlock debugging uses "current" a lot).

Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] uml: fix not_dead_yet when directory is in bad state

The bug occurred to me when a UML left an empty ~/.uml/Sarge-norm folder -
when trying to reuse not_dead_yet() failed one of its check.  The comment
says that's ok and means that we can take the directory, but while normally
not_dead_yet() removes it and returns 0 (i.e.  go on, use this), on failure
it returns 0 but forgets to remove it.  The fix is to remove it anytime
we're going to return 0.

But since "not_dead_yet" didn't make the interface so clear, causing this
bug, and I couldn't find a convenient name for the mix of things it did, I
split it into two parts:

is_umdir_used()      - returns a boolean, contains all checks of not_dead_yet()
umdir_take_if_dead   - tries to remove the dir unless it's used - returns
whether it removed it, that is we now own it.

With this changes the control flow is IMHO a bit clearer and needs less
comment for control flow.

Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] uml: make copy_*_user atomic

Make __copy_*_user_inatomic really atomic to avoid "Sleeping function called in
atomic context" warnings, especially from futex code.

This is made by adding another kmap_atomic slot and making copy_*_user_skas
use kmap_atomic; also copy_*_user() becomes atomic, but that's true and is not
a problem for i386 (and we can always add might_sleep there as done
elsewhere).  For TT mode kmap is not used, so there's no need for this.

I've had to use another slot since both KM_USER0 and KM_USER1 are used
elsewhere and could cause conflicts.  Till now we reused the kmap_atomic slot
list from the subarch, but that's not needed as that list must contain the
common ones (used by generic code) + the ones used in architecture specific
code (and Uml till now used none); so I've taken the i386 one after comparing
it with ones from other archs, and added KM_UML_USERCOPY.

Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] SMP alternatives: skip with UP kernels

Hide the magic in alternative.h and provide some dummy inline functions
for the UP case (gcc should manage to optimize away these calls).  No
changes in module.c.

Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: namespace cleanup: replace ips with ipath

Remove ips namespace from infinipath drivers.  This renames ips_common.h to
ipath_common.h.  Definitions, data structures, etc.  that were not used by
kernel modules have moved to user-only headers.  All names including ips have
been renamed to ipath.  Some names have had an ipath prefix added.

Signed-off-by: Christian Bell <christian.bell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: ignore receive queue size if SRQ is specified

The receive work queue size should be ignored if the QP is created to use a
shared receive queue according to the IB spec.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: remove some #if 0 code related to lockable memory

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: fix a bug that results in addresses near 0 being written via DMA

We can't tell for sure if any packets are in the infinipath receive buffer
when we shut down a chip port.  Normally this is taken care of by orderly
shutdown, but when processes are terminated, or sending process has a bug, we
can continue to receive packets.  So rather than writing zero to the address
registers for the closing port, we point it at a dummy memory.

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: read/write correct sizes through diag interface

We must increment uaddr by size we are reading or writing, since it's passed
as a char *, not a pointer to the appropriate size.

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: support more models of InfiniPath hardware

We do a few more explicit checks for specific models, and now also support the
old PathScale serial number style, or new QLogic style.

This is backwards compatible with previous versions of software and hardware.
That is, older software will see a plausible serial number and correct GUID
when used with a new board, while newer software will correctly handle an
older board.

Signed-off-by: Mike Albaugh <mike.albaugh@qlogic.com>
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: drop the "stats" sysfs attribute group

This attribute group made it into the original driver, but should not have.

Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: purge sps_lid and sps_mlid arrays

The two arrays only had space for 4 units.

Also changed from ipath_set_sps_lid() to ipath_set_lid(); the sps was
leftover.

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: rC receive interrupt performance changes

This patch separates QP state used for sending and receiving RC packets so the
processing in the receive interrupt handler can be done mostly without locks
being held.  ACK packets are now sent without requiring synchronization with
the send tasklet.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: fixes to performance get counters for IB compliance

This patch fixes some problems uncovered during IB compliance testing to
return the right values for error counters returned by the Performance Get
Counters packet.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: check for valid LID and multicast LIDs

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: removed redundant statements

The tail register read became redundant as the result of earlier receive
interrupt bug fixes.

Drop another unneeded register read.

And another line that got duplicated.

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: don't confuse the max message size with the MTU

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: disallow send of invalid packet sizes over UD

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: fix lost interrupts on HT-400

Do an extra check to see if in-memory tail changed while processing packets,
and if so, going back through the loop again (but only once per call to
ipath_kreceive()).  In practice, this seems to be enough to guarantee that if
we crossed the clearing of an interrupt at start of ipath_intr with a
scheduled tail register update, that we'll process the "extra" packet that
lost the interrupt because we cleared it just as it was about to arrive.

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: fixed bug 9776 for real

The problem was that I was updating the head register multiple times in the
rcvhdrq processing loop, and setting the counter on each update.  Since that
meant that the tail register was ahead of head for all but the last update, we
would get extra interrupts.  The fix was to not write the counter value except
on the last update.

I also changed to update rcvhdrhead and rcvegrindexhead at most every 16
packets, if there were lots of packets in the queue (and of course, on the
last packet, regardless).

I also made some small cleanups while debugging this.

With these changes, xeon/monty typically sees two openib packets per interrupt
on sdp and ipoib, opteron/monty is about 1.25 pkts/intr.

I'm seeing about 3800 Mbit/s monty/xeon, and 5000-5100 opteron/monty with
netperf sdp.  Netpipe doesn't show as good as that, peaking at about 4400 on
opteron/monty sdp.  Plain ipoib xeon is about 2100+ netperf, opteron 2900+, at
128KB

Signed-off-by: olson@eng-12.pathscale.com
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: reduce overhead on receive interrupts

Also count the number of interrupts where that works (fastrcvint).  On any
interrupt where the port0 head and tail registers are not equal, just call the
ipath_kreceive code without reading the interrupt status, thus saving the
approximately 0.25usec processor stall waiting for the read to return.  If any
other interrupt bits are set, or head==tail, take the normal path, but that
has been reordered to handle read ahead of pioavail.  Also no longer call
ipath_kreceive() from ipath_qcheck(), because that just seems to make things
worse, and isn't really buying us anything, these days.

Also no longer loop in ipath_kreceive(); better to not hold things off too
long (I saw many cases where we would loop 4-8 times, and handle thousands (up
to 3500) in a single call).

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: memory management cleanups

Made in-memory rcvhdrq tail update be in dma_alloc'ed memory, not random user
or special kernel (needed for ppc, also "just the right thing to do").

Some cleanups to make unexpected link transitions less likely to produce
complaints about packet errors, and also to not leave SMA packets stuck and
unable to go out.

A few other random debug and comment cleanups.

Always init rcvhdrq head/tail registers to 0, to avoid race conditions (should
have been that way some time ago).

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: use vmalloc to allocate struct ipath_devdata

This is not a DMA target, so no need to use dma_alloc_coherent on it.

Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: use more appropriate gfp flags

This helps us to survive better when memory is fragmented.

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: enable freeze mode when shutting down device

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: print better debug info when handling 32/64-bit DMA mask problems

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: removed unused field ipath_kregvirt from struct ipath_devdata

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: enforce device resource limits

These limits are somewhat artificial in that we don't actually have any
device limits.  However, the verbs layer expects that such limits exist
and are enforced, so we make up arbitrary (but sensible) limits.

Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: report correct device identification information in /sys

Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: return an error for unknown multicast GID

Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: fix some memory leaks on failure paths

Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: don't allow resources to be created with illegal values

Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: remove some duplicate code

Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: update some comments and fix typos

Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: allow diags on any unit

There is no longer a /dev/ipath_diag file; instead, there's
/dev/ipath_diag0, 1, etc.

It's still not possible to have diags run on more than one unit at a time,
but that's easy to fix at some point.

Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: fix shared receive queues for RC

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: fix an indenting problem

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: share more common code between RC and UC protocols

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: update copyrights and other strings to reflect new company name

Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IB/ipath: name zero counter offsets so it's clear they aren't counters

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] ACPI: fix not power-manageable device message

Fix typo in message.

Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] EDAC: fix module names quoted in sysfs

Fix the quoted module name in the sysfs for EDAC modules and reported by several
people.

Instead of  ../_edac_e752x_/   now the following will be presented, like other
modules:   ../edac_e752x/

Signed-off-by: Doug Thompson <norsk5@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IRQ: warning message cleanup

Make warnings more consistent.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] IRQ: Use SA_PERCPU_IRQ, not IRQ_PER_CPU, for irqaction.flags

IRQ_PER_CPU is a bit in the struct irq_desc "status" field, not in the
struct irqaction "flags", so the previous code checked the wrong bit.

SA_PERCPU_IRQ is only used by drivers/char/mmtimer.c for SGI ia64 boxes.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] pi-futex: futex_wake() lockup fix

Fix futex_wake() exit condition bug when handling the robust-list with PI
futexes on them.

(reported by Ulrich Drepper, debugged by the lock validator.)

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] pi-futex: fix mm_struct memory leak

lock_queue was getting called essentially twice in a row and was
continually incrementing the mm_count ref count, thus causing a memory
leak.

Dinakar Guniguntala provided a proper fix for the problem that simply grabs
the spinlock for the hash bucket queue rather than calling lock_queue.

The second time we do a queue_lock in futex_lock_pi, we really only need to
take the hash bucket lock.

Signed-off-by: Dinakar Guniguntala <dino@in.ibm.com>
Signed-off-by: Vernon Mauery <vernux@us.ibm.com>
Acked-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

kbuild: documentation change on allowing checkers besides sparse

Minor documentation change on allowing checkers besides sparse

This patch cleans up a couple of mentions of sparse in the inline
toplevel Makefile documentation such that it's clear that other checkers
besides sparse can override CHECK and CHECKFLAGS.

Signed-off-by: Dustin Kirkland <dustin.kirkland@us.ibm.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>

[PATCH] audit syscall classes

Allow to tie upper bits of syscall bitmap in audit rules to kernel-defined
sets of syscalls.  Infrastructure, a couple of classes (with 32bit counterparts
for biarch targets) and actual tie-in on i386, amd64 and ia64.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

kbuild: warn when a moduled uses a symbol marked UNUSED

We now have infrastructure in place to mark an EXPORTed symbol
as unused. So the natural next step is to warn during buildtime when
a module uses a symbol marked UNUSED.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>

[PATCH] audit: support for object context filters

This patch introduces object audit filters based on the elements
of the SELinux context.

Signed-off-by: Darrel Goeddel <dgoeddel@trustedcs.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
 kernel/auditfilter.c           |   25 +++++++++++++++++++++++++
 kernel/auditsc.c               |   40 ++++++++++++++++++++++++++++++++++++++++
 security/selinux/ss/services.c |   18 +++++++++++++++++-
 3 files changed, 82 insertions(+), 1 deletion(-)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

[PATCH] audit: rename AUDIT_SE_* constants

This patch renames some audit constant definitions and adds
additional definitions used by the following patch.  The renaming
avoids ambiguity with respect to the new definitions.

Signed-off-by: Darrel Goeddel <dgoeddel@trustedcs.com>
 include/linux/audit.h          |   15 ++++++++----
 kernel/auditfilter.c           |   50 ++++++++++++++++++++---------------------
 kernel/auditsc.c               |   10 ++++----
 security/selinux/ss/services.c |   32 +++++++++++++-------------
 4 files changed, 56 insertions(+), 51 deletions(-)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

[PATCH] add rule filterkey

Add support for a rule key, which can be used to tie audit records to audit
rules.  This is useful when a watched file is accessed through a link or
symlink, as well as for general audit log analysis.

Because this patch uses a string key instead of an integer key, there is a bit
of extra overhead to do the kstrdup() when a rule fires.  However, we're also
allocating memory for the audit record buffer, so it's probably not that
significant.  I went ahead with a string key because it seems more
user-friendly.

Note that the user must ensure that filterkeys are unique.  The kernel only
checks for duplicate rules.

Signed-off-by: Amy Griffis <amy.griffis@hpd.com>

kbuild: fix segv in modpost

Parsing an old Modules.symvers file casued modpost to SEGV.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>

kconfig: enhancing accessibility of lxdialog

Some fix that I forgot for good accessibility of lxdialog (the cursor
should always be left at the focus location):

Have the checklist display the currently highlighted entry last, for having
the cursor left on it (rather than on the last line of the list).

Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>

kbuild: fix ia64 breakage after introducing make -rR

kbuild used $¤(*F to get filename of target without extension.
This was used in several places all over kbuild, but introducing
make -rR broke his for all cases where we specified full path to
target/prerequsite. It is assumed that make -rR disables old style
suffix-rules which is why is suddenly failed.

ia64 was impacted by this change because several div* routines in
arch/ia64/lib are build using explicit paths and then kbuild failed.

Thanks to David Mosberger-Tang <David.Mosberger@acm.org> for an explanation
what was the root-cause and for testing on ia64.

This patch also fixes two uses of $(*F) in arch/um

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>

Merge /pub/scm/linux/kernel/git/davem/sparc-2.6

* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Kill sun4v virtual device layer.
  [SERIAL] sunhv: Convert to of_driver layer.
  [SPARC64]: Mask out top 8-bits in physical address when building resources.
  [SERIAL] sunsu: Missing return statement in su_probe().

Merge /pub/scm/linux/kernel/git/davem/net-2.6

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [IPV6]: Added GSO support for TCPv6
  [NET]: Generalise TSO-specific bits from skb_setup_caps
  [IPV6]: Added GSO support for TCPv6
  [IPV6]: Remove redundant length check on input
  [NETFILTER]: SCTP conntrack: fix crash triggered by packet without chunks
  [TG3]: Update version and reldate
  [TG3]: Add TSO workaround using GSO
  [TG3]: Turn on hw fix for ASF problems
  [TG3]: Add rx BD workaround
  [TG3]: Add tg3_netif_stop() in vlan functions
  [TCP]: Reset gso_segs if packet is dodgy

Merge branch 'for-linus' of /linux/kernel/git/roland/infiniband

* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
  IB/core: Set alternate port number when initializing QP attributes
  IB/uverbs: Set correct user handle for user SRQs

Merge git://git./linux/kernel/git/bunk/trivial

* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
  Remove obsolete #include <linux/config.h>
  remove obsolete swsusp_encrypt
  arch/arm26/Kconfig typos
  Documentation/IPMI typos
  Kconfig: Typos in net/sched/Kconfig
  v9fs: do not include linux/version.h
  Documentation/DocBook/mtdnand.tmpl: typo fixes
  typo fixes: specfic -> specific
  typo fixes in Documentation/networking/pktgen.txt
  typo fixes: occuring -> occurring
  typo fixes: infomation -> information
  typo fixes: disadvantadge -> disadvantage
  typo fixes: aquire -> acquire
  typo fixes: mecanism -> mechanism
  typo fixes: bandwith -> bandwidth
  fix a typo in the RTC_CLASS help text
  smb is no longer maintained

Manually merged trivial conflict in arch/um/kernel/vmlinux.lds.S

Merge git://git./linux/kernel/git/brodo/pcmcia-2.6/

* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6/:
  [PATCH] pcmcia: fix deadlock in pcmcia_parse_events
  [PATCH] com20020_cs: more device support
  [PATCH] au1xxx: pcmcia: fix __init called from non-init
  [PATCH] kill open-coded offsetof in cm4000_cs.c ZERO_DEV()
  [PATCH] pcmcia: convert pcmcia_cs to kthread
  [PATCH] pcmcia: fix kernel-doc function name
  [PATCH] pcmcia: hostap_cs.c - 0xc00f,0x0000 conflicts with pcnet_cs
  [PATCH] pcmcia: at91_cf suspend/resume/wakeup
  [PATCH] pcmcia: Make ide_cs work with the memory space of CF-Cards if IO space is not available
  [PATCH] pcmcia: TI PCIxx12 CardBus controller support
  [PATCH] pcmcia: warn if driver requests exclusive, but gets a shared IRQ
  [PATCH] pcmcia: expose tool in pcmcia/Documentation/pcmcia/
  [PATCH] pcmcia: another ID for serial_cs.c
  [PATCH] yenta: fix hidden PCI bus numbers
  [PATCH] yenta: do power-up only after socket is configured

Merge /pub/scm/linux/kernel/git/mchehab/v4l-dvb

* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
  V4L/DVB (4290): Add support for the TCL M2523_3DB_E tuner.
  V4L/DVB (4289): Missing statement in drivers/media/dvb/frontends/cx22700.c
  V4L/DVB (4288): Clean out a zillion sparse warnings in pvrusb2
  V4L/DVB (4287): Pvrusb2/: possible cleanups
  V4L/DVB (4285): Cx88: add support for Geniatech Digistar / Digiwave 103g
  V4L/DVB (4284): Cx24123: fix set_voltage function according to the specs
  V4L/DVB (4282): Fix: use swzigzag for swalgo
  V4L/DVB (4281): TDA9887_SET_CONFIG should only be handled by the tda9887.
  V4L/DVB (4277): Fix CI interface on PRO KNC1 cards
  V4L/DVB (4276): Fix CI on old KNC1 DVBC cards
  V4L/DVB (4275): The FE_SET_FRONTEND_TUNE_MODE ioctl always returns EOPNOTSUPP
  V4L/DVB (4274): Eliminate use of tda9887 from pvrusb2 driver
  V4L/DVB (4273): Always log pvrusb2 device register / unregister events
  V4L/DVB (4272): Fix tveeprom supported standards
  V4L/DVB (4270): Add tda9887-specific tuner configuration
  V4L/DVB (4269): Subject: videocodec: make 1-bit fields unsigned
  V4L/DVB (4267): Remove all instances of request_module("tda9887")
  V4L/DVB (4264): Cx88-blackbird: implement VIDIOC_QUERYCTRL and VIDIOC_QUERYMENU

Merge branch 'release' of git://git./linux/kernel/git/lenb/linux-acpi-2.6

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (25 commits)
  ACPI: Kconfig: ACPI_SRAT depends on ACPI
  ACPI: drivers/acpi/scan.c: make acpi_bus_type static
  ACPI: fixup memhotplug debug message
  ACPI: ACPICA 20060623
  ACPI: C-States: only demote on current bus mastering activity
  ACPI: C-States: bm_activity improvements
  ACPI: C-States: accounting of sleep states
  ACPI: additional blacklist entry for ThinkPad R40e
  ACPI: restore comment justifying 'extra' P_LVLx access
  ACPI: fix battery on HP NX6125
  ACPIPHP: prevent duplicate slot numbers when no _SUN
  ACPI: static-ize handle_hotplug_event_func()
  ACPIPHP: use ACPI dock driver
  ACPI: dock driver
  KEVENT: add new uevent for dock
  ACPI: asus_acpi_init: propagate correct return value
  [ACPI] Print error message if remove/install notify handler fails
  ACPI: delete tracing macros from drivers/acpi/*.c
  ACPI: HW P-state coordination support
  ACPI: un-export ACPI_ERROR() -- use printk(KERN_ERR...)
  ...

[SPARC64]: Kill sun4v virtual device layer.

Replace with a simple IRQ translater in the PROM
device tree builder.

Signed-off-by: David S. Miller <davem@davemloft.net>

[SERIAL] sunhv: Convert to of_driver layer.

Signed-off-by: David S. Miller <davem@davemloft.net>

[SPARC64]: Mask out top 8-bits in physical address when building resources.

These top 8-bits are supposed to be ignored in the ranges and
top-level reg properties on this platform.

Signed-off-by: David S. Miller <davem@davemloft.net>

[SERIAL] sunsu: Missing return statement in su_probe().

If we have a keyboard/mouse port, don't drop through to
calling sunsu_autoconfig().

Signed-off-by: David S. Miller <davem@davemloft.net>

[IPV6]: Added GSO support for TCPv6

This patch adds GSO support for IPv6 and TCPv6.  This is based on a patch
by Ananda Raju <Ananda.Raju@neterion.com>.  His original description is:

This patch enables TSO over IPv6. Currently Linux network stacks
restricts TSO over IPv6 by clearing of the NETIF_F_TSO bit from
"dev->features". This patch will remove this restriction.

This patch will introduce a new flag NETIF_F_TSO6 which will be used
to check whether device supports TSO over IPv6. If device support TSO
over IPv6 then we don't clear of NETIF_F_TSO and which will make the
TCP layer to create TSO packets. Any device supporting TSO over IPv6
will set NETIF_F_TSO6 flag in "dev->features" along with NETIF_F_TSO.

In case when user disables TSO using ethtool, NETIF_F_TSO will get
cleared from "dev->features". So even if we have NETIF_F_TSO6 we don't
get TSO packets created by TCP layer.

SKB_GSO_TCPV4 renamed to SKB_GSO_TCP to make it generic GSO packet.
SKB_GSO_UDPV4 renamed to SKB_GSO_UDP as UFO is not a IPv4 feature.
UFO is supported over IPv6 also

The following table shows there is significant improvement in
throughput with normal frames and CPU usage for both normal and jumbo.

--------------------------------------------------
|          |     1500        |      9600         |
|          ------------------|-------------------|
|          | thru     CPU    |  thru     CPU     |
--------------------------------------------------
| TSO OFF  | 2.00   5.5% id  |  5.66   20.0% id  |
--------------------------------------------------
| TSO ON   | 2.63   78.0 id  |  5.67   39.0% id  |
--------------------------------------------------

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

[NET]: Generalise TSO-specific bits from skb_setup_caps

This patch generalises the TSO-specific bits from sk_setup_caps by adding
the sk_gso_type member to struct sock.  This makes sk_setup_caps generic
so that it can be used by TCPv6 or UFO.

The only catch is that whoever uses this must provide a GSO implementation
for their protocol which I think is a fair deal :) For now UFO continues to
live without a GSO implementation which is OK since it doesn't use the sock
caps field at the moment.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

[IPV6]: Added GSO support for TCPv6

This patch adds GSO support for IPv6 and TCPv6.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

[IPV6]: Remove redundant length check on input

We don't need to check skb->len when we're just about to call
pskb_may_pull since that checks it for us.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

[NETFILTER]: SCTP conntrack: fix crash triggered by packet without chunks

When a packet without any chunks is received, the newconntrack variable
in sctp_packet contains an out of bounds value that is used to look up an
pointer from the array of timeouts, which is then dereferenced, resulting
in a crash. Make sure at least a single chunk is present.

Problem noticed by George A. Theall <theall@tenablesecurity.com>

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

[TG3]: Update version and reldate

Update version to 3.61.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>