net: build_ehash_secret() and rt_bind_peer() cleanups

Now cmpxchg() is available on all arches, we can use it in
build_ehash_secret() and rt_bind_peer() instead of using spinlocks.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlge: pull NULL check ahead of dereference

There was a dereference before NULL check issue introduced in 1e213303d
"qlge: Add tx multiqueue support."  I've pulled the NULL check of
"net_rsp" forward a couple lines to avoid that.

Also Ron Mercer says that the early exit should be above the index
write.  ql_write_cq_idx(rx_ring);

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tehuti: Use net_device_stats from struct net_device

struct net_device has its own struct net_device_stats member, so use
this one instead of a private copy in the bdx_priv struct.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

ep93xx_eth: Use net_device_stats from struct net_device

struct net_device has its own struct net_device_stats member, so use
this one instead of a private copy in the ep93xx_priv struct. As the new
ndo_get_stats function would just return dev->stats we can omit it.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net_sched: sch_sfq: use proto_ports_offset() to support AH message

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netfilter: xt_hashlimit: use proto_ports_offset() to support AH message

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netfilter: ipt_CLUSTERIP: use proto_ports_offset() to support AH message

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net_sched: cls_flow: use proto_ports_offset() to support AH message

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: rps: use proto_ports_offset() to handle the AH message correctly

The SPI isn't at the beginning of an AH message.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: introduce proto_ports_offset()

Introduce proto_ports_offset() for getting the position of the ports or
SPI in the message of a protocol.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: rps: skip fragment when computing rxhash

Fragmented IP packets may have no transfer header, so when computing
rxhash, we should skip them.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: rps: reset network header before calling skb_get_rxhash()

skb_get_rxhash() assumes the network header pointer of the skb is set
properly after the commit:

commit bfb564e7391340638afe4ad67744a8f3858e7566
Author: Krishna Kumar <krkumar2@in.ibm.com>
Date:   Wed Aug 4 06:15:52 2010 +0000

    core: Factor out flow calculation from get_rps_cpu

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: update version 5.0.8

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: rom lock recovery

Fw can get stuck while holding pci semaphore. Driver will not
be able to perform fw initialization, without this lock.
Release semaphore forcefully in that case.

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: firmware initialization update

Cleanup legacy code which is not valid for Qlogic
CNA adapters.

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: fix endiness in eswitch statistics

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: mark device state as failed

Mark device state failed in error path.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: fix npar state

Privilege functions should wait for npar state to be operational.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: support anti mac spoofing

Administrator can configure to drop packet in transmit,
if it doesn't match interface mac address, in case of virtual function.

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: configure offload setting on eswitch

Device is not capable of enabling/disabling offload setting per
port in case of Nic Partition.So offload settings needs to be
enabled/disabled per eswitch and it will affect all the function
on that eswitch.

Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: configure port on eswitch

o Nic partition capable devices has embedded switch, this needs to support
various features like external switch.

Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: replace magic numbers with defines

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: remove unused code

Serial number references are not used in driver.

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: fix inconsistent lock state

Spin_lock(rds_ring->lock) is not required while posting buffers
from qlcnic_open and freeing buffers from qlcnic_down.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: rewrite ethtool test to use standard config functions

This change makes it so that the ethtool loopback test uses the standard
ring configuration and allocation functions.  As a result the loopback test
will be much more effective at testing core driver functionality.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: update all DESC_ADV macros to accept a ring pointer

All of the DESC_ADV macros are currently needing the pointers to be
de-referenced before accessing the ring.  Instead of having to add all of
the asterisks it is easier to just update the macro to expect a pointer to
the ring.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: combine Rx into into ixgbe_configure_rx

The Rx init is currently split over ixgbe_configure, ixgbe_configure_rx,
and ixgbe_up_complete.  Instead of leaving it split over 3 function it is
easier to consolidate them all into ixgbe_configure_rx.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: pull all Tx init into ixgbe_configure_tx

The Tx init was spread out over ixgbe_configure, ixgbe_configure_tx, and
ixgbe_up_complete.  This change combines all of that into the
ixgbe_configure_tx function in order to simplify the Tx init path.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: move all GPIE register config into a single function

This change moves all GPIE register configuration into a single function.
The advantage of this is that we can avoid a number of unnecessary
read/modify/write cycles on the register.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: Move virtualization config into a separate function

This change moves the configuration that was done in configure_rx into a
separate virtualization configuration function.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: move all Rx DMA control register writes to one central location

This change moves all of the Rx DMA control register writes to one central
location.  This should help to avoid accidentally overwriting existing
settings.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: Move max frame size and Rx buffer length configuration into a function

This change consolidates all of the Rx max frame size and Rx buffer length
configuration into a single function.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: remove redundant configuration of vmolr, rename generic variable

The vmolr is configured already in ixgbe_set_rx_mode for the PF so there is
no need to set it again in ixgbe_configure_rx.

Instead of using the variable name reg, it is easier to just rename it to
gcr_ext to reflect the register contents that the variable holds.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: bump PS header size to 512 bytes

Bump the header size for packet split to 512 bytes since this makes the
best use of the 1k buffer that is allocated for any skb 512 bytes or
smaller.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: combine accesses to FCTRL register into ixgbe_set_rx_mode

We are accessing the FCTRL register in multiple spots in the init path and
we can simplify things by combining the configuration all into
ixgbe_set_rx_mode.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: pull PSRTYPE configuration into a separate function

The configuration of PSRTYPE was being done conditionally on if packet
split is enabled or not.  It can be configured always since it will not
have any effect when packet split is not enabled.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: pull ring configuration into it's own function

These changes add ixgbe_configure_rx_ring which is used to setup the base
function pointers for the ring.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: consolidate all setting of MRQC into one function

This change simplifies the configuration of MRQC by consolidating the
setting of it into one function. As such the register is no longer set in
multiple places which should make any future changes easier to work with.
In addition we can combine RSS related register writes into the call since
enabling all of those bits without enabling RSS itself in MRQC should have
no effect.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: move Tx ring configuration into a separate function

This patch moves the Tx ring configuration into a separate function.  In
addition the function drops the setting of the head writeback RO bit since
head writeback is no longer used within ixgbe.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: move configuration of the MTQC register into it's own function

This patch moves the configuration of the MTQC register into it's own
function call similar to ixgbe_setup_mrqc.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: combine two modifications of TXDCTL into one

In ixgbe_up_complete we were doing a read-modify-write of TXDCTL followed
by another one just a few lines further down.  Instead of performing two
separate read-modify-writes it would make more sense to combine the two
into one.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: move setting of GSO size for 82598 into ixgbe_configure_dcb

We are unnecessarily modifying the GSO size for all HW when we don't need
to.  The code can be simplified by moving the check for DCB and the
adjustment of the GSO size for 82598 into ixgbe_configure_dcb.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: remove redundant DMA alignment code

This patch removes the redundant DMA alignment code from the Rx buffer
allocation path.  This code is no longer necessary since all x86 buffers
are now DMA aligned due to recent changes to NET_IP_ALIGN and NET_SKB_PAD.

It also moves the setting of the Rx queue value into the allocation path
since it is more likely that the queue mapping will still be in the cache
at the time of allocation.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: cleanup ixgbe_get_drvinfo to be extra careful with buffer boundaries

Make the code in ixgbe_get_drvinfo more protected against buffer overflow
boundaries by using snprintf and sizeof with snprintf.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xilinx_emaclite: netpoll support

Netconsole requires poll support.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

slip: fix get_stats() method

Use integrated net_device_stats instead of a static one, and make sure
no transient values are feeded. ndo_get_stats() can be called by
concurrent cpus.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vxge: Implement 64bit stats

vxge_get_stats() is racy, since it clears a block of memory (net_stats)
possibly still used by other cpus.

We can update this driver to full 64bit stats, since ndo_get_stats64()
provides a private block to store results, and driver maintains 64bit
counters already.

We also remove net_stats field from struct vxge_sw_stats

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

atm: remove a net_device_stats clear

No need to clear device stats in lec_open()

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ether3: Use net_device_stats from struct net_device

struct net_device has its own struct net_device_stats member, so use
this one instead of a private copy in the ether1_priv struct. As the new
ndo_get_stats function would just return dev->stats we can omit it. This
patch also removes an incorrect memset of the stats on open.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

ether1: Use net_device_stats from struct net_device

struct net_device has its own struct net_device_stats member, so use
this one instead of a private copy in the ether1_priv struct. As the new
ndo_get_stats function would just return dev->stats we can omit it. This
patch also removes an incorrect memset of the stats on open.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: simplify flags for tx timestamping

This patch removes the abstraction introduced by the union skb_shared_tx in
the shared skb data.

The access of the different union elements at several places led to some
confusion about accessing the shared tx_flags e.g. in skb_orphan_try().

    http://marc.info/?l=linux-netdev&m=128084897415886&w=2

Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/sunvnet.c: Use pr_<level> and netdev_<level>

Use the current message logging styles.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/sungem: Use netdev_<level>, netif_<level> and pr_<level>

Use the current logging message styles.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sunhme: Use return value of register_netdev

Use the return value provided by register_netdev on error instead of
using a previously set value.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

greth: Use return value of register_netdev

Use the return value provided by register_netdev on error instead of
hard setting it to -ENOMEM.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/qlcnic: Use available error codes

The error code is stored in the variable err, but it is the variable ret
that is returned instead.  So store the error code in ret.  Err is then
useless.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
local idexpression x;
constant C;
@@

if (...) { ...
  x = -C
  ... when != x
(
  return <+...x...+>;
|
  return NULL;
|
  return;
|
* return ...;
)
}
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/ax25: Use available error codes

Error codes are stored in err, but the return value is always 0.  Return
err instead.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
local idexpression x;
constant C;
@@

if (...) { ...
  x = -C
  ... when != x
(
  return <+...x...+>;
|
  return NULL;
|
  return;
|
* return ...;
)
}
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/ax25: Use available error codes

Error codes are stored in err, but the return value is always 0.  Return
err instead.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
local idexpression x;
constant C;
@@

if (...) { ...
  x = -C
  ... when != x
(
  return <+...x...+>;
|
  return NULL;
|
  return;
|
* return ...;
)
}
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/pcmcia: Use pr_<level> and netdev_<level>

On Mon, 2010-08-09 at 17:34 +0200, Dominik Brodowski wrote:
> look good from a PCMCIA point of view, therefore:
> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>

If PCMCIA is still being looked after, then here's
another for you, maybe for 2.6.37.

Use the more descriptive logging message styles.

There are whitespace/indentation errors in the original
sources that these changes do not modify, so checkpatch
errors were cheerfully ignored.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/sched: remove unneeded NULL check

There is no need to check "s".  nla_data() doesn't return NULL.  Also we
already dereferenced "s" at this point so it would have oopsed ealier if
it were NULL.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s2io: Update driver version

Update s2io driver's version to reflect the series of patches.

Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s2io: remove unused code

usr_addrs is never referenced outside the initial struct population
during open, thus making it unnecessary.  Remove it, the code that
references it, and the struct that it is the only user of.

Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net: Convert unbounded kzalloc calls to kcalloc

These changes may be slightly safer in some instances.

There are other kzalloc calls with a multiply, but those
calls are typically "small fixed #" * sizeof(some pointer)"
and those are not converted.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Prevent missing name table entries when link flip-flops rapidly

Ensure that TIPC does not re-establish communication with a
neighboring node until it has finished updating all data structures
containing information about that node to reflect the earlier loss of
contact.  Previously, it was possible for TIPC to perform its purge of
name table entries relating to the node once contact had already been
re-established, resulting in the unwanted removal of valid name table
entries.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Allow connect() to wait indefinitely

Cause a socket whose TIPC_CONN_TIMEOUT option is zero to wait
indefinitely for a response to a connection request using connect().
Previously, specifying a timeout of 0 ms resulted in an immediate
timeout, which was inconsistent with the behavior specified by Posix
for a socket's receive and send timeout.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Minor enhancements to name table display format

Eliminate printing of dashes after name table column headers
(to adhere more closely to the standard format used in tipc-config),
and simplify name table display logic using array lookups rather
than if-then-else logic.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Optimize tipc_node_has_active_links()

Eliminate unnecessary checking for null node pointer and redundant
check of second active link array entry.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Remove per-connection sequence number logic

Remove validation of the per-connection sequence numbers on routable
connections, since routable connections are not supported by TIPC.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Fix bug in broadcast link transmit statistics computation

Modify TIPC's broadcast link so that it counts each piece of a
fragmented message individually, rather than as treating the group
as a single message.  This ensures that proper correlation of sent
and received traffic can be done when the broadcast link statistics
are displayed, and is consistent with the way fragments are counted
by TIPC's unicast links.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Fix premature broadcast advertisement by sending node

Prevent a TIPC node from sending out a LINK_STATE message
advertising a broadcast message that it is in the process
of sending, but has not yet actually sent.  Previously, it was
possible for a link timeout to occur in between the time the
broadcast link updated its "last message sent" counter and the
time the broadcast message was passed to the broadcast bearer
for transmission.  This ensures that the code which issues
the LINK_STATE message isn't informed of the new message until
the broadcast bearer has had a chance to send it.

Note: The "last message sent" value is stored in the "fsm_msg_count"
field of the link structure used by the broadcast link.  Since the
broadcast link doesn't utilize the normal link FSM, this field can
be re-used rather than adding a new field to the broadcast link.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Prevent crash when broadcast link cannot send to all nodes

Allow TIPC's broadcast link to continue operation when it is unable
to send a message to all nodes in the cluster.  Previously, the
broadcast link attempted to put the broadcast pseudo-bearer into a
blocked state; however, this caused a crash because the associated
bearer structure is only partially initialized.  Further
investigation has revealed some conceptual problems with blocking
the pseudo-bearer; consequently, this functionality has been
disabled for the time being and the undelivered message is
eventually resent by the broadcast link's existing message
retransmission mechanism (if possible).

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Check for disabled bearer when processing incoming messages

Add a check to tipc_recv_msg() to ensure it discards messages
arriving on a newly disabled bearer.  This is needed to deal with a
race condition that can arise if the bearer is in the midst of being
disabled when it receives a message.  Performing the check after
tipc_net_lock has been taken ensures that TIPC's bearers are in a
stable state while the message is being processed.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: correct problems with misleading flags returned using poll()

Prevent TIPC from incorrectly setting returned flags to poll()
in the following cases:

- an unconnected socket no longer indicates that it is always readable

- an unconnected, connecting, or listening socket no longer indicates
  that it is always writable

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Provide correct error code for unsupported connect() operation

Modify TIPC to return EOPNOTSUPP if an application attempts to perform
 a non-blocking connect() operation, which is not supported by TIPC.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: add SO_RCVLOWAT support to stream socket receive path

Add support for the SO_RCVLOWAT socket option to TIPC's stream socket
type.

Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Fix log buffer memory leak if initialization fails

Moves log buffer cleanup into tipc_core_stop() so that memory allocated
for the log buffer is freed if tipc_core_start() is unsuccessful.

Signed-off-by: Anders Kaseorg <andersk@ksplice.com>
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: turn off lro when rxcsum is disabled.

o Also dont allow lro to be turn on, if rx csum is disabled

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: fix link diag test

o Give sufficient time for all makes of PHY modules
  to establish the link after loopback test.
o Perform online test before offline test.

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: fix link status message

Display interface name with netdev_info() for link status message.

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: add eswitch statistics support

Adding eswitch statistics support. User can get
whole eswitch stats or stats of func belong to that eswitch.

Added:
o command to get statistics of eswitch and function.
o sysfs support to export eswitch and func statatistics.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: fix for setting function modes

function modes was not working with CNA device, in CNA mode
other function(FCOE) can be enabled before nic.

Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: device state management fixes for virtual func

o NPAR state should be set to operationl by Mangement function only.
o NPAR state should be set to non operational before device reset.
o VF function should wait for NPAR state to be operational.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: fix aer for virtual func

Virtual function are not privilge to initialize firmware.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

enic: Mark intr_timer in vnic_enet_config as deprecated

Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

enic: Check if rq/wq buf not NULL before freeing them

Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

enic: Clean up: remove enic_dev_stats_clear

Remove function enic_dev_stats_clear and its reference in enic device
init code. Firmware clears device stats on device open. So, no need for
the driver to do it again.

Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

enic: Use offsetof macro in vic tlv length calculation

Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

enic: Add new firmware devcmds

Add new firmware devcmds:  CMD_PROXY_BY_INDEX, CMD_CONFIG_INFO_GET

Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

enic: Add support for firmware management device

This patch adds support for firmware management device in enic driver.
A management device is a virtual PCIe device that firmware can present
to the host as its management endpoint. It provides the interface between
the host and adapter firmware for all management operations.

Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

enic: Add set mac address

This patch implements the ndo_set_mac_address netdev operation for an enic device

Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cpmac: fix all checkpatch errors and warnings

This patches fixes a couple of checkpatch warnings and errors:
- lines over 80 columns
- printk() instead of pr_cont()
- assignments in tests (if ((foo == bar())))

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

am79c961a: Use net_device_stats from struct net_device

struct net_device has its own struct net_device_stats member, so we can
use this one instead of a private copy in the dev_priv struct.

Cc: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

r6040: fix all checkpatch errors and warnings

This patch fixes a couple of errors and warnings spotted by checkpatch.pl:
- some lines were over 80 columns
- there were some whitespaces left

The call to printk is now replaced by a call to pr_info and the log-level
included in the driver version is now removed, so there are no longer false
positives on this warning.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

pcnet_cs: Use pr_fmt and pr_<level>

It looks as if the printks in get_ax88190 are
incorrect and were duplicated and superceded by a
test in pcnet_config, so I removed them.

Changed the level of the ax88190 test to KERN_NOTICE
to match the other message styles in pcnet_config.

Compiled but untested.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pcnet_cs: Use proper netdev_*-printouts

To prevent broken messages like:

[  204.024291] eth%d: pcnet_reset_8390() did not complete.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Joe Perches <joe@perches.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool: Provide a default implementation of ethtool_ops::get_drvinfo

The driver name and bus address for a net_device can normally be found
through the driver model now.  Instead of requiring drivers to provide
this information redundantly through the ethtool_ops::get_drvinfo
operation, use the driver model to do so if the driver does not define
the operation.  Since ETHTOOL_GDRVINFO no longer requires the driver
to implement any operations, do not require net_device::ethtool_ops to
be set either.

Remove implementations of get_drvinfo and ethtool_ops that provide
only this information.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/decnet: Adjust confusing if indentation

Indent the branch of an if.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@

(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

if (p1[0].column == p2[0].column):
  cocci.print_main("branch",p1)
  cocci.print_secs("after",p2)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/isdn: Adjust confusing if indentation

In hisax/hfc_sx.c and mISDN/l1oip_core.c, the code after the if is
outdented so that it is not aligned with the if branch.

In mISDN/dsp_cmx.c, an else is added between the original if branch and the
following statement, in line with the code following it.  Without this
change, the first assignment to dsp->rx_W has no useful effect.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@

(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

if (p1[0].column == p2[0].column):
  cocci.print_main("branch",p1)
  cocci.print_secs("after",p2)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net: Adjust confusing if indentation

Outdent the code following the if.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@

(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

if (p1[0].column == p2[0].column):
  cocci.print_main("branch",p1)
  cocci.print_secs("after",p2)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/hamradio: Adjust confusing if indentation

Indent the branch of an if.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@

(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

if (p1[0].column == p2[0].column):
  cocci.print_main("branch",p1)
  cocci.print_secs("after",p2)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>