[SCSI] qla2xxx: Do not restrict the number of NPIV ports for ISP83xx.

Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Do PCI fundamental reset for ISP83xx

On ISP83xx cards perform a fundamental reset instead of hot reset.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Fail initialization if unable to load RISC code.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Ensure PLOGI is sent to Fabric Management-Server upon request.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Remove setting Scsi_host->this_id during adapter probe.

Setting this to 255 will cause any target with id 255 to not show up so leave
it at the default in our host template.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Use #defines instead of hardcoded values for intr status.

Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Dont call nic restart firmware if it is already active and running.

Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Wrong PCIe(2.5Gb/s x8) speed in the kerenel message for ISP82xx.

qla2xxx show wrong PCIe(2.5Gb/s x8) speed in the kerenel message. It should be
5.0Gb/s.

Signed-off-by: Atul Deshmukh <atul.deshmukh@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Perform ROM mbx cmd access only after ISP soft-reset during f/w recovery.

Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Implement beacon support for ISP83xx.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Fix for continuous rescan attempts in arbitrated loop topology.

Stale information in the temporary fcport created in
qla2x00_configure_local_loop() causes qla2x00_get_port_database() call
to fail. This reschedules scan, which gets stuck continuously in the
rescheduling-of-scan loop due to the failure.

Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Only enable link up on the correct interrupt event.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Update the driver copyright.

Update the driver copyright from 2003-2011 to 2003-2012.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Don't register to legacy interrupt for ISP82xx.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Changes for ISP83xx loopback support.

Minor changes to support loopback functionality with ISP83xx CNAs.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add bit to identify adapters for thermal temp.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Implemetation of mctp.

[jejb: fix up checkpatch errors]
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: IDC implementation for ISP83xx.

Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add FW DUMP SIZE sysfs attribute.

Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Implementation of bidirectional.

[jejb: merge fix for introduced warning]
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Use bitmap to store loop_id's for fcports.

Store used fcport loop_id's in a bitmap so that as opposed to looping through
all fcports to find the next free loop_id, new loop_id lookup can be just be
done via bitops.

[jejb: plus fix for incorrect LOOPID_MAP_SIZE from Andrew Vasquez]
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Display mailbox failure by default.

Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Fix typo in qla2xxx files

Correct spelling typo within qla2xxx files.

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add check in qla82xx_watchdog for failed hardware state.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add I2C BSG interface.

Add BSG interface to generically access I2C attached devices.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Bind to ISP8031 devices.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] Fusion MPT: disable pci device when mpt map resoures failed

when probe a pci device, first we enable it, and disable it when
some error happened in the following process, because the power
state of the device is set to D0, and if MSI is disabled,
we will allocate irq and register gsi for this device in the enable process.

In function mpt_mapresources(MPT_ADAPTER *ioc), it forgot disable the
pci device when error happened, the irq and gsi will never be released.
this patch will fix it.

Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: "Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] st: raise device limit

The device limit of 128 tape drives was established in 2003 as a
significant increase from the 8 tape drives allowed previously.

We're seeing customer sites that between a large number of drives
and multipath are discovering more than 128 devices and running
into problems.

Now that we're not stuck having to store a pointer in array
and aren't limited by kmalloc failing on higher order allocs we can
lift the limit to fill the entire minor range based on the number
of modes.

Based on the current code, that's 2^17 devices.

Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] st: clean up device file creation and removal

This patch cleans up the st device file creation and removal.

Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] st: get rid of scsi_tapes array

st currently allocates an array to store pointers to all of the
scsi_tape objects. It's used to discover available indexes to use as the
base for the minor number selection and later to look up scsi_tape
devices for character devices.

We switch to using an IDR for minor selection and a pointer from
st_modedef back to scsi_tape for the lookups.

Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] st: clean up dev cleanup in st_probe

st_probe leaves a cdev pointer hanging around that is compared
during the error path and freed later. There's no need for the pointer
to hang around at all. So we free it immediately and simplify the error
handling.

Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] st: Use static class attributes

st currently sets up and tears down class attributes manually for
every tape drive in the system. This patch uses a statically defined
class with class attributes to let the device core do it for us.

Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] be2iscsi: Bump the driver version.

Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] be2iscsi: Fix a kernel panic because of TCP RST/FIN received.

A TCP RST/FIN can be received even before the connection specific
structures are initialized.This fix checks for the conn structure
is intialized or not  when RST/FIN is received.

Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] be2iscsi: Add support for configuring the VLAN on the adapter.

Add support for configuring the VLAN parameters on the adapter
using the iscsiadm interface.

Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] be2iscsi: Format the MAC_ADDR with sysfs_format_mac.

The MAC_ADDR stored in driver private structure is of
unsigned char data type but strlcpy parameters is of
signed char data type. This conversion of data types
lead to change in the value.This changed value is passed
to the upper layer and junk characters were displayed
when "iscsiadm -m iface" command was run.

In case of iSCSI boot, since the the MAC_ADDR was coming
junk the boot was also not working

Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] be2iscsi: Added Logging mechanism for the driver.

Added new log level mechanism for different events. These
log levels can be set at driver load time/run time. The
log level is set for each Scsi_host.

Fixed few multi-line print warning to get over the new checkpatch.pl
warnings on multi-line strings.

Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] be2iscsi: Issue MBX Cmd for login to boot target in crashdump mode

When the driver comes up in crashdump mode, it has to explicitly
issue command to FW for logging to the boot target. This fix issues
MBX Cmd to login to boot target in crashdump mode.

Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] be2iscsi: Removing the iscsi_data_pdu setting.

The setting of iscsi_data_pdu is not required anymore,
as this was required for BE1 adapters only. The BE1 adapter
were not supported in any previous versions of the kernel.

Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.34: Update lpfc version for 8.3.34 driver release

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.34: Fixed leaking memory from pci dma pool

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.34: Correct lock handling to eliminate reset escalation on I/O abort

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.34: Adjust IO Channels to 1 when INTx

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.34: Add XRI to abort handler timeout log message

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.34: Streamline fcp underrun message printing

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.34: Correct typecasts for snprintf messages

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.34: Simplify BlockGuard lpfc_printf_vlog messages

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.34: Fix parameter field in CQE to mask for LOCAL_REJECT status

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.34: Fix number of IO channels to match CPUs

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.34: Add SLI-4 V1 Capacity and Resource Descriptor support

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.34: Add LOGO support after ABTS compliance

Make compliant with FC specs by sending LOGO after ABTS timeouts

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] scsi_lib: Set the device state from transport-offline to running

FC and iSCSI class set SCSI devices to transport-offline state after
fast_io_fail/replacement_timeout has fired, but after relogin, function
scsi_internal_device_unblock() is not setting scsi device state to running.
Due to this the devices even after being relogged in remain offline.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Update driver version to 5.02.00-k19

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Properly handle SCSI underrun while processing status IOCBs.

The current code would incorrectly return a DID_OK for a
CHECK CONDITION with Recovered error sense key causing incorrect
completion of a command when there is a dropped frame.

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Fix multiple conn login event issue during session recovery.

During iscsid session recovery driver sends multiple ISCSI_CONN_STATE_LOGGED_IN
event from qla4xxx_conn_start() and qla4xxx_ddb_change(), which causes iscsid
to crash.

Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Fix gcc warning for x86 system

Fix warning:-
drivers/scsi/qla4xxx/ql4_nx.c:1867:2: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 5 has type ‘uint32_t’ [-Wformat]

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Fix memory corruption issue in qla4xxx_ep_connect.

In qla4xxx_ep_connect(), qla_ep->dst_addr and dst_addr are type
struct sockaddr. We are copying sizeof(struct sockaddr_in6) bytes
from dst_addr to qla_ep->dst_addr which is 12 bytes larger. This
will cause memory corruption. So we change qla_ep->dst_addr to
struct sockaddr_storage which is of 128 byte, large enough to
hold sizeof(struct sockaddr_in6).

Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] mvsas: Fix oops when ata commond timeout.

Kernel message follows:

[  511.712011] sd 11:0:0:0: [sdf] command ffff8800a4e81400 timed out
[  511.712022] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[  511.712024] sas: trying to find task 0xffff8800a4d24c80
[  511.712026] sas: sas_scsi_find_task: aborting task 0xffff8800a4d24c80
[  511.712029] drivers/scsi/mvsas/mv_sas.c 1631:mvs_abort_task()
mvi=ffff8800b5300000 task=ffff8800a4d24c80 slot=ffff8800b5325038
slot_idx=x0
[  511.712035] BUG: unable to handle kernel NULL pointer dereference at
0000000000000058
[  511.712040] IP: [<ffffffff815f8c0c>] _raw_spin_lock_irqsave+0xc/0x30
[  511.712047] PGD 0
[  511.712049] Oops: 0002 [#1] SMP
[  511.712052] Modules linked in: mvsas libsas scsi_transport_sas
raid456 async_pq async_xor xor async_memcpy async_raid6_recov raid6_pq
async_tx [last unloaded: mvsas]
[  511.712062] CPU 3
[  511.712066] Pid: 7322, comm: scsi_eh_11 Not tainted 3.5.0+ #106 To Be
Filled By O.E.M. To Be Filled By O.E.M./To be filled by O.E.M.
[  511.712068] RIP: 0010:[<ffffffff815f8c0c>]  [<ffffffff815f8c0c>]
_raw_spin_lock_irqsave+0xc/0x30
[  511.712073] RSP: 0018:ffff880098d3bcb0  EFLAGS: 00010086
[  511.712074] RAX: 0000000000000286 RBX: 0000000000000058 RCX:
00000000000000c3
[  511.712076] RDX: 0000000000000100 RSI: 0000000000000046 RDI:
0000000000000058
[  511.712078] RBP: ffff880098d3bcb0 R08: 000000000000000a R09:
0000000000000000
[  511.712080] R10: 00000000000004e8 R11: 00000000000004e7 R12:
ffff8800a4d24c80
[  511.712082] R13: 0000000000000050 R14: ffff8800b5325038 R15:
ffff8800a4eafe00
[  511.712084] FS:  0000000000000000(0000) GS:ffff8800bdb80000(0000)
knlGS:0000000000000000
[  511.712086] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[  511.712088] CR2: 0000000000000058 CR3: 00000000a4ce6000 CR4:
00000000000407e0
[  511.712090] DR0: 0000000000000000 DR1: 0000000000000000 DR2:
0000000000000000
[  511.712091] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7:
0000000000000400
[  511.712093] Process scsi_eh_11 (pid: 7322, threadinfo
ffff880098d3a000, task ffff8800a61dde40)
[  511.712095] Stack:
[  511.712096]  ffff880098d3bce0 ffffffff81060683 ffff880000000000
0000000000000000
[  511.712099]  ffff8800a4d24c80 ffff8800b5300000 ffff880098d3bcf0
ffffffffa0076a88
[  511.712102]  ffff880098d3bd50 ffffffffa0079bb5 ffff880000000000
ffff880000000018
[  511.712106] Call Trace:
[  511.712110]  [<ffffffff81060683>] complete+0x23/0x60
[  511.712115]  [<ffffffffa0076a88>] mvs_tmf_timedout+0x18/0x20 [mvsas]
[  511.712119]  [<ffffffffa0079bb5>] mvs_slot_complete+0x765/0x7d0
[mvsas]
[  511.712125]  [<ffffffffa005a17d>] sas_scsi_recover_host+0x55d/0xdb0
[libsas]
[  511.712128]  [<ffffffff8106d600>] ? idle_balance+0xe0/0x130
[  511.712133]  [<ffffffff813b150c>] scsi_error_handler+0xcc/0x470
[  511.712136]  [<ffffffff815f7ad0>] ? __schedule+0x370/0x730
[  511.712139]  [<ffffffff8105f728>] ? __wake_up_common+0x58/0x90
[  511.712142]  [<ffffffff813b1440>] ? scsi_eh_get_sense+0x110/0x110
[  511.712146]  [<ffffffff810571be>] kthread+0x8e/0xa0
[  511.712150]  [<ffffffff816015f4>] kernel_thread_helper+0x4/0x10
[  511.712153]  [<ffffffff81057130>] ? flush_kthread_work+0x120/0x120
[  511.712156]  [<ffffffff816015f0>] ? gs_change+0xb/0xb
[  511.712157] Code: 8a 00 01 00 00 89 d0 f0 66 0f b1 0f 66 39 d0 0f 94
c0 0f b6 c0 5d c3 0f 1f 84 00 00 00 00 00 55 48 89 e5 9c 58 fa ba 00 01
00 00 <f0> 66 0f c1 17 0f b6 ce 38 d1 74 11 0f 1f 84 00 00 00 00 00 f3
[  511.712191] RIP  [<ffffffff815f8c0c>] _raw_spin_lock_irqsave+0xc/0x30
[  511.712194]  RSP <ffff880098d3bcb0>
[  511.712196] CR2: 0000000000000058
[  511.712198] ---[ end trace a781c7b1e65db92c ]---

Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.33: Update lpfc version for 8.3.33 driver release

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.33: Fixed incomplete list of SLI4 commands with extended timeout value

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.33: Fixed debugfs queInfo to include queue stats

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.33: Add lpfc_fcp_look_ahead module parameter

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.33: Make I/O to hw queue distribution algorithm a module parameter

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.33: Change Naming convention for SLI4 Interrupt vector

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.33: Allow per-hba interrupt rate tuning

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.33: Tie parallel I/O queues into separate MSIX vectors

Add fcp_io_channel module attribute to control amount of parallel I/O queues

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.33: Add Interrupts per second stats via debugfs

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.33: Parallelize SLI-4 Q distribution

Commonize SLI-3/4 Ring/Queue framework, to keep SLI-3 compatibility
Parallelize SLI-4 Q distribution - to use multiple posting/completion queues

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.33: Misc changes to optimize critical path

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.33: Formally separate lpfc_sli_ring SLI-3 and SLI-4 variantions

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.33: Convert to no SCSI host lock in queuecommand

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.33: Add debugfs interface to display SLI queue information

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.33: Fix error when remote port switches address

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.33: Fix scsi_eh escalation panic by checking the proper return status

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.33: Check data transfer amount on write commands

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.33: Fix error of not reiniting mbx cmd before reissue

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.33: Fix bug with rrq_pool not being destroyed during driver removal.

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.33: Enable attachment to OCe14000 adapters

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.33: When doing loopback testing, set the diag valid bit

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] ibmvscsi: Add maintainer for IBM virtual SCSI/FC drivers

Add a MAINTAINERS entry for the IBM Power Virtual SCSI and FC device
drivers.

Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] ipr: remove an unneeded check

"rc" is always zero here, so there is no need to check.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] ipr: missing unlock before a return

We recently changed the locking in this function, but this return was
missed.  It needs an unlock and the IRQs need to be restored.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] add DID_TARGET_FAILURE and DID_NEXUS_FAILURE to hostbyte_table in constants.c

Without this patch, scsi_show_result prints hostbyte as invalid for statuses
that are not defined in hostbyte_table (when scsi logging is enabled).

Signed-off-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] hpsa: use ioremap_nocache instead of ioremap

I think ioremap() ends up being equivalent to ioremap_nocache
by default, but we should signal our intent that these mappings
should be non-cacheable.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] hpsa: fix incorrect abort diagnostic message

In the abort handler, when asked to abort a command which
is not known to the driver, SUCCESS is returned, but the
diagnostic message incorrectly indicates the abort failed.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] hpsa: Use LUN reset instead of target reset

It turns out Smart Array logical drives do not support target
reset and when the target reset fails, the logical drive will
be taken off line.  Symptoms look like this:

hpsa 0000:03:00.0: Abort request on C1:B0:T0:L0
hpsa 0000:03:00.0: resetting device 1:0:0:0
hpsa 0000:03:00.0: cp ffff880037c56000 is reported invalid (probably means target device no longer present)
hpsa 0000:03:00.0: resetting device failed.
sd 1:0:0:0: Device offlined - not ready after error recovery
sd 1:0:0:0: rejecting I/O to offline device
EXT3-fs error (device sdb1): read_block_bitmap:

LUN reset is supported though, and is what we should be using.
Target reset is also disruptive in shared SAS situations,
for example, an external MSA1210m which does support target
reset attached to Smart Arrays in multiple hosts -- a target
reset from one host is disruptive to other hosts as all LUNs
on the target will be reset and will abort all outstanding i/os
back to all the attached hosts.  So we should use LUN reset,
not target reset.

Tested this with Smart Array logical drives and with tape drives.
Not sure how this bug survived since 2009, except it must be very
rare for a Smart Array to require more than 30s to complete a request.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] megaraid_sas: Version and Changelog update

Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] megaraid_sas: Add resetwaittime module parameter

This allows a user to adjust the wait time in seconds after I/O timeout before
resetting the adapter.

Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] megaraid_sas: Add throttlequeuedepth module parameter

This allows a user to adjust the queue depth of the adapter when throttled due
to I/O timeout.

Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] ipr: Driver version 2.5.4

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] ipr: Reduce interrupt lock time

Reduce the amount of time the host lock is held in the interrupt handler
for improved performance.

[jejb: fix up checkpatch noise]
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] ipr: Reduce queuecommand lock time

Reduce the amount of time the host lock is held in queuecommand
for improved performance.

[jejb: fix up checkpatch noise]
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] mpt2sas: Bump driver vesion to 14.100.00.00

Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] mpt2sas: Fix for With post diag reset same set of device gets added, removed and then again gets added with new target ids

When device discovery is disabled during driver load time using module
parameter "disable_discovery=1" and when diag reset is issued then from logs,
it is observed that the devices get added, removed and then added with new
target ids.

So, in order to limit this turn-off the code which is deleting and devices
across host reset when the disable_discovery module parameter is turned on.

Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] mpt2sas: Fix for staged device discovery functionality of driver not working

This patch provides a command line option to disable "Port enable" during
the driver load.

The objective of this command line option is to load the driver and do
all the necessary initialization excluding port enable(i.e. delay
device discovery)

Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] mpt2sas : MPI 2.0 Rev V(2.0.14) specification

Changeset in MPI 2.0 Rev V(2.0.14) specification

        1) Bumped MPI2_HEADER_VERSION_UNIT.
        2) Added a product specific range to event values.
        3) Added clarification to Direct-Attached SAS PHY Power condition.
        4) Updated timing requirements for performing Hard Reset.

Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] mpt2sas: Fix for max_sectors warning message is stating the incorrect range

When specifying the command line option "max_sectors" less than 64, then
warning message should provide correct upper boundary value 32767 instead of
8192.

Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] mpt2sas: Provide sysfs attribute to report Backup Rail Monitor Status

A new sysfs shost attribute called "BMR_status" is implemented to
report Backup Rail Monitor status.

This attribute is located in the path
        /sys/class/scsi_host/host#/BMR_status

when reading this adapter attribute, then driver will output the state
of GPIO[24]. It returns "0" if BMR is healthy and it returns "1" for failure.

if it returns an empty string then it means that there was an error while
obtaining the BMR status. Then check dmesg for what error has occured.

Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] mpt2sas: To include more Intel Branding

Updating the customer branding string for "SSD 910 Series" controller

Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] mpt2sas: 2012 source code copyright

The Copyright String in all the drivers sources were changed to 2012

Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>