carl9170: import 1.9.6 firmware headers

Import new headers from my firmware branch:
<https://github.com/chunkeey/carl9170fw>

visit our wiki at:
<http://wireless.kernel.org/en/users/Drivers/carl9170.fw>

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: remove debugging masks from AR_MCI_INTERRUPT_RX_MSG_DEFAULT

Remove the CONT_* and LNA_* messages from
AR_MCI_INTERRUPT_RX_MSG_DEFAULT. Those MCI rx messages only
meant for debugging purpose. Including them in default rx_msg
series could raise huge amount of MCI interrupts when BT traffic
is going on. And also it increases power consumption when WLAN
is scanning.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: handle non PCI devices in the phy code

Some code in write_{radio,radio}_reg() should just be run if this is a
pci based device. Add the condition again which was removed in commit:
commit 821e4e93172e4f7d5ac1eade04665c3dc5049c4a
Author: Roland Vossen <rvossen@broadcom.com>
Date:   Mon Aug 8 15:58:58 2011 +0200

    staging: brcm80211: removed unused bus code from softmac

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: fix read in write_phy_reg

This reverts a unintended change mad in commit.
commit 4b006b11ca18995677c5f1cd03cc9c42fbe80693
Author: Arend van Spriel <arend@broadcom.com>
Date:   Thu Dec 8 15:06:54 2011 -0800

    brcm80211: smac: use bcma functions for register access in phy code

Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: extend brcms_c_chipmatch() to also handle non PCIe devices

Now brcms_c_chipmatch() is also able to handle non PCI devices and also
does some checking for SoC if they are supported by brcmsmac.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: fix DMA on SoCs

These extra offsets are only needed by PCIe devices and not when
running on an SoC.

This partly reverts commit:
commit 821e4e93172e4f7d5ac1eade04665c3dc5049c4a
Author: Roland Vossen <rvossen@broadcom.com>
Date:   Mon Aug 8 15:58:58 2011 +0200

    staging: brcm80211: removed unused bus code from softmac

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: extend xmtfifo_sz array

The xmtfifo_sz array contains the queue sizes for the different core
revs. This array missed the sizes for the core rev 17 and 28. This
patch extends the array to also include these sizes and adds a warning
if no queue size is stored in the array for the given core rev.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: add some workarounds for other chips again

This adds some workarounds for the BCM4716, BCM47162, BCM5357 to the
phy code again. This patch reverts parts of the following patch.

commit c2c724977f95135f397fe0cb45f3c041d26b91e1
Author: Arend van Spriel <arend@broadcom.com>
Date:   Wed Jun 29 16:46:35 2011 -0700

    staging: brcm80211: remove unsupported chipset code from brcmsmac phy

The BCM4716 is working for me with an other firmware and I am working
on adding support for the other chips.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: add a conditions for core rev 17 again

This reverts some changes made in this commit:
commit 7234592364e2efe8b4ac1040c99b1d7ef01cf502
Author: Roland Vossen <rvossen@broadcom.com>
Date:   Mon Feb 14 12:16:45 2011 +0100

    staging: brcm80211: removal of inactive d11 code

The bcm4716 has a rev 17 wireless core and this condition is needed.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: remove some unnessessacry casts and void pointer

Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: use chip and package id constants from bcma

This patch depends on addin the chip IDs to bcma done in this commit in
my pending patch series for bcma.
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date:   Sun Jun 3 18:17:57 2012 +0200

    bcma: add constants for chip ids

Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: use core id constants from bcma

This patch depends on adding the IDs to bcma done in
this commit in my pending patch series for bcma.
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date:   Sun Jun 3 18:17:57 2012 +0200

    bcma: add constants for chip ids

Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: remove some redundant chip common workarounds

The removed workarounds are already performed in bcma_pmu_workarounds()
and bcma_core_chipcommon_init()

This patch depends on the completion of the workarounds in bcma done in
this commit in my pending patch series for bcma.
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date:   Mon Jun 4 00:20:26 2012 +0200

    bcma: complete workaround for BCMA43224 and BCM4313

Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: remove si_pmu_spuravoid_pllupdate()

si_pmu_spuravoid_pllupdate() is now replaced by
bcma_pmu_spuravoid_pllupdate() which does the same thing, but supports
more chips.

This function is in my pending patch series for bcma.
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date:   Mon Jun 4 01:31:32 2012 +0200

    bcma: add bcma_pmu_spuravoid_pllupdate()

Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: remove si_pmu_init() and si_pmu_res_init()

This is already done by bcma_pmu_init() and bcma_pmu_resources_init() in bcma.

Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: remove ai_findcore()

bcma also stores a pointer to the chipcommon core in its struct,
brcmsmac should use it and not search for the core by its own.

Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: use container_of instead of cast

Now "struct si_pub pub" does not have to be the first member in struct
si_info any more, if it is the resulting code after compilation should
be the same.

Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: remove ai_get_buscore{type,rev}()

These two functions are not used any more.

Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: remove PCI_FORCEHT() macro

The BCM4716 is a SoC and does not have a PCI client interface, so this
condition is never true.

Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: remove PCIE() macro

Instead of checking if there is a PCIe core on the bus, better check if
hosttype is PCIe.

In the original submission to staging PCIE() checked, if the bustype is
PCI and the buscore is a PCIe core. Now we assume that all cores bcma
supports are PCIe based, so we just have to check if the bustype is PCI.

The old code bcmsmac currently uses searches for a PCIe core on the bus
and if there is one assumes that this is the buscore, which is wrong.
Some SoCs have a PCIe core operating in host mode and this is not the
bus core. The old code also caused a null pointer in
ai_get_buscoretype() and ai_get_buscorerev() if buscore was not set
because there was no PCIe core on the bus.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: remove driver for unavailable hardware

This hardware never became available to normal humans.  Leaving this
driver imposes unwelcome maintenance costs for no clear benefit.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>

wlcore: fix a couple small memory leaks

We should free "chunk" here before returning the error code.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: determine AP extra rates correctly

Don't use the ht_mode module parameter for determining AP supported
rates. We can rely on channel type, since HT40 won't be enabled if our
HT cap doesn't support it.

Enable MIMO only if there enough antennas, and rely on per-peer rate
limitation to prevent IOPs.

Signed-off-by: Arik Nemtsov <arik@wizery.com>

wlcore: check ssid length against the correct element

commit 587cc28 ("wlcore: compare ssid_len before comparing
ssids") introduced a new bug - the ssid length from the
request struct was compared against the ssid length of
another request, instead the one of the cmd.

This might cause the sched scan request to fail
(with -EINVAL) in many cases.

Signed-off-by: Eliad Peller <eliad@wizery.com>

wl12xx/wl18xx: use a dynamic PS timeout of 1.5sec

It seems some parties have bad user experience when smaller values
are used. This should have little implications for power consumption,
since traffic is bursty in nature.

Signed-off-by: Arik Nemtsov <arik@wizery.com>

wlcore: define number of supported bands internally

Avoid using the IEEE80211_NUM_BANDS constant for arrays sizes etc, as
this can contain bands unsupported by the driver (e.g. 60Ghz). Use an
internal constant to determine the number of bands.

Signed-off-by: Arik Nemtsov <arik@wizery.com>

wlcore: don't set SDIO_FAILED flag when driver state is off

If some IO read/write fails while the FW is not loaded, a recovery
will not take place. This means the SDIO_FAILED flag will stay in place
forever and prevent further read/writes.

This can happen if a check for STATE_OFF was forgotten in some routine.

Take this opportunity to rename the flag to IO_FAILED, since we support
other buses as well.

Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

wlcore: change the wait for event mechanism

wlcore needs to wait for certain events for example
for roc complete event. Usually the events are received
from the FW very fast, therefore wlcore can poll with
a short delay and if after a second the event was
not received yet poll with a long (1-5 msec) delay.

This implementation is similar to the sending of
commands to the FW.

Empirically the change reduced the wait for roc event
from ~10-40msec to 100s of usecs.

[replace udelay/msleep with usleep_range - Arik]

Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

wlcore: Prevent processing of work items during op_stop

The interrupt line is disabled in op_stop using disable_irq. Since
pending interrupts are synchronized, the mutex has to be released before
disabling the interrupt to avoid a deadlock with the interrupt handler.

In addition, the internal state of the driver is only set to 'off'
after the interrupt is disabled. Otherwise, if an interrupt fires after
the state is set but before the interrupt line is disabled, the
interrupt handler will not be able to acknowledge the interrupt
resulting in an interrupt storm.

The driver's operations might be called during recovery. If these
acquire the mutex after it was released by op_stop, but before the
driver's state is changed, they may queue new work items instead of just
failing. This is especially problematic in the case of scans, in which a
new scan may be scheduled after all scan requests were cancelled.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

wlcore: implement .flush callback

implement the .flush() callback by simply calling wl1271_tx_flush().

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx/wlcore: increase FW filename version

We have some API changes and new features in the new firmwares that
are not compatible with older drivers.  Increase the version of the FW
filenames for wl12xx to 5.

Additionally, remove the duplicate definitions from wlcore_i.h and
remove the MODULE_FIRMWARE macro calls from the SDIO and SPI modules,
since they're irrelevant there.

Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: add probe request templates for sched and one-shot scans

The driver configures the firmware template for probe requests during
the scan process.  If the same template is used for one-shot and sched
scans they will override each other when running scans simultaneously.

This fix works only on firmwares later than X.3.9.2.112 for single
role and X.3.9.2.23 for multi-role.

[Some cleaning-up and renaming of the quirk to something smaller --
Luca.]

Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: always clear recovery flag during recovery_work

If recovery is called when the FW is off, we should clear the recovery
flag. Otherwise we risk booting the driver in permanent pending-recovery
state.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: avoid debug prints during intended FW recovery

Don't read the FW panic log or print other debug data when recovery is
intended (i.e. FW type switch). This takes valuable time and can be
confusing to the user.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: remove recover cmd from testmode

This command is buggy (doesn't take the mutex) and unused. Instead, the
"start_recovery" file is used for the same purpose. Remove the code but
keep the command constant to avoid breaking the testmode ABI.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: don't stop tx queue via watermark if already stopped

If a Tx queue is currently stopped because of our Tx watermark flow
control, don't stop it again. This causes a warning to appear.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore/wl12xx/wl18xx: check min FW version

Refuse to boot if the FW version is too old. The minimum version is set
per chip, with the option of setting it per PG in the future.

When boot fails because of an old FW, display a helpful message.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: enable sched scan while connected

New wl12xx firmware supports scheduled scans also while connected.
Stop blocking sched scan requests when connected and add a quirk to
block in hardware that don't support it (currently wl18xx doesn't).

This requires FW version 6/7.3.10.2.112 for single-role and
6/7.5.6.0.25 for multi-role.

Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

NFC: Check for llcp_sock and its device from llcp_sock_getname

They both can potentially be NULL.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Add ISO 14443 type B protocol

Some devices (e.g. Sony's PaSoRi) can not do type B polling, so we have
to make a distinction between ISO14443 type A and B poll modes.

Cc: Eric Lapuyade <eric.lapuyade@intel.com>
Cc: Ilan Elias <ilane@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Use communicate thru only for PaSoRi when trying to read Felica tags

Otherwise DATA_EXCHANGE seems to be just fine.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Add initial Sony RC-S360 support to pn533

Sony RC-S360 is also known as the Sony PaSoRi contactless reader.
Only type 2, 3 and 4 tag reading is supported at the moment.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Dereference LLCP bind socket address after checking for it to be NULL

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Do not return EBUSY when stopping a poll that's already stopped

We check for the polling flag before checking if the netlink PID caller
match.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Remove warning from nfc_llcp_local_put

The socket local pointer can be NULL when a socket is created but never
bound or connected.

Reported-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Handle LLCP Disconnected Mode frames

When receiving such frame, the sockets waiting for a connection to finish
should be woken up. Connecting to an unbound LLCP service will trigger a
DM as a response.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: LLCP late binding

With the LLCP 16 local SAPs we can potentially quickly run out of source
SAPs for non well known services.
With the so called late binding we will reserve an SAP only when we actually
get a client connection for a local service. The SAP will be released once
the last client is gone, leaving it available to other services.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Forbid SSAP binding to a not well known LLCP service

With not Well Known Services there is no guarantees as to which
SSAP the server will be listening on, so there is no reason to
support binding to a specific source SAP.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Forbid LLCP service name reusing

This patch fixes a typo and return the correct error when trying to
bind 2 sockets to the same service name.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Release LLCP SAP when the owner is released

The LLCP SAP should only be freed when the socket owning it is released.
As long as the socket is alive, the SAP should be reserved in order to
e.g. send the right wks array when bringing the MAC up.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Close listening LLCP sockets when the device is gone

When the MAC link goes down, we should only keep the bound sockets
alive. They will be closed by sock_release or when the underlying
NFC device is moving away.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Build LLCP general bytes upon request

Drivers will need them before starting a poll or when being activated
as targets. Mostly WKS can have changed between device registration and
then so we need to re-build the whole array.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Fix LLCP getname socket op

Set the right target index and use a better socket declaration routine.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Update LLCP socket target index when getting a connection

Getting a valid CONNECT means we have a valid target index.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Add netlink module alias for NFC

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Add modules alias for NFC sockets

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Allow HCI driver to pre-open pipes to some gates

Some NFC chips will statically create and open pipes for both standard
and proprietary gates. The driver can now pass this information to HCI
such that HCI will not attempt to create and open them, but will instead
directly use the passed pipe ids.

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: update PN544 HCI driver state when opened/closed

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Error management documentation

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: nfc_driver_failure() implementation

If the device is polling we sent a 0 target found event.

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: nfc_targets_found() should accept zero target found

The semantics for a zero target found event is that the polling operation
could not complete.

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Core must test the device polling state inside the device lock

There can ever be only one call to nfc_targets_found() after polling
has been engaged. This could be from a target discovered event from
the driver, or from an error handler to notify poll will never complete.

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Implement HCI driver or internal error management

If there is an ongoing HCI command executing, it will be completed,
thereby pushing the error up to the core. Otherwise, HCI will directly
notify the core with the error.

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Factorize HCI cmd completion

HCI cmd can be completed either from an HCI response or from an
internal driver or HCI error. This requires to factorize the
completion code outside of the device lock.

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Driver failure API

This API should be used by drivers, HCI, SHDLC or NCI stacks to report an
unrecoverable error.

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Changed HCI cmd execution completion result to std linux errno

An HCI command can complete either from an HCI response
(with an HCI result) or as a consequence of any other system
error during processing. The completion therefore needs to take
a standard errno code. The HCI response will convert its result
to a standard errno before calling the completion.

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Implement HCP reaggregation allocation error case

We can now report an ENOMEM error up to the HCI layer.

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Remove an impossible HCI error case

nfc_hci_recv_frame can not be called with a NULL skb.

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Handle SHDLC RSET frames from an SHDLC connected chip

shdlc reset may leave HCI in an inconsistent state by loosing parts of
HCI frames. Handle this case by reporting an unrecoverable error to HCI.

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Removed addressed shdlc TODOs

The questions asked in the comments have been answered and addressed.

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Prepare asynchronous error management for driver and shdlc

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

ath9k: Stop the BTCOEX timers before disabling BTCOEX

Its safe to stop the BTCOEX timers 'period_timer' and
'no_stomp_timer' before disabling BTCOEX. These timers
can call ath9k_hw_btcoex_enable (or) change the BT
stomp type if they seem to be running after we had
called ath9k_hw_btcoex_disable, which is obviously
not correct.

Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix MCI cleanup

We are doing MCI cleanup eventhough BTCOEX is not enabled
via module parameter. This means we do ath_mci_cleanup
though we skipped calling ath_mci_setup. Yet it does not
causes any issues now  as we free the DMA buffer allocated
only when it is allocated during ath_mci_setup.

Reviewed-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: use custom printing functions

Having bus number printed makes it much easier to anaylze logs on
systems with more buses. For example Netgear WNDR4500 has 3 AMBA buses
in total, which makes standard log really messy.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: fix RSSI calibration

Specs were updated, change code to match it.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: fix brcms_c_regd_init() which crashed after 11ad patch

This patch fixes an OOPS in brcmsmac driver, which was introduced
by the 11ad patch 'cfg80211: add 802.11ad (60gHz band) support'.
The value IEEE80211_NUM_BANDS increased, which was used in the
brcms_c_regd_init() function.

Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Acked-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: enable support for AR9550

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: set 4ADDRESS bit in RX filter for AR9550

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: enable PLL workaround for AR9550

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix PLL initialization for AR9550

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: skip internal regulator configuration for AR9550

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: disable SYNC_HOST1_FATAL interrupts for AR9550

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix RF channel frequency configuration for AR9550

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix PAPRD settings for AR9550

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix antenna control configuration for AR9550

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix XPABIASLEVEL settings for AR9550

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: read spur frequency information from eeprom for AR9550

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add mode register initialization code for AR9550

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add initvals for AR9550

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: enable TX/RX data byte swap for AR9550

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: clear pciexpress flag for AR9550

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add BB name string for AR9550

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add platform_device_id for AR9550

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: set MAC version for AR9550

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: define MAC version for AR9550

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: define DEVID for QCA955x

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net/wireless: remove macro defined twice with same value

In the list of commands CMD_802_11_EEPROM_ACCESS had been
defined twice, unnecessarily, luckily with same value.

Remove one occurence.

Signed-off-by: Oskar Schirmer <oskar@scara.com>
Cc: Marcelo Tosatti <marcelo@kvack.org>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: add set_antenna handler support

This enables user to set mode of Tx/Rx path using "iw set antenna"
command. For non MIMO chips, the command will be used for selecting
specific antenna or configuring antenna diversity mode.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix AR9462 2g5g switch on full reset

On full reset, mci reset will put LNA update on 2G mode. And
Whenever 2g5g_switch is forced at the end of full reset, lna
update should not be skipped. Not doing so, is affecting WLAN
rx and causing beacon loss when BTCOEX is enabled on AR9462.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix power consumption on network sleep when BTCOEX is enabled

The chip is waken up for every 45ms in btcoex timer cycle to
for sharing the radio between BT and WLAN. Whenever the wlan
interface is in network sleep mode, do not schedule hw timers.
This could reduce power consumption on idle associated state.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>