MIPS: ralink: copy the commandline from the devicetree

This is a regression caused by:
commit afb46f7996e91aeb36e07bc92cf96e8045bec00e
Author: Rob Herring <robh@kernel.org>
Date:   Wed Apr 2 19:07:24 2014 -0500
mips: ralink: convert to use unflatten_and_copy_device_tree

Make the of init code reuse the cmdline defined inside the dts.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8008/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: add a bootrom dumper module

This patch adds a trivial driver that allows userland to extract the bootrom of
a SoC via debugfs.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8002/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: add rt3883 wmac clock

Register the wireless mac clock on rti3883. This is required by the wifi driver.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8007/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: add rt2880 wmac clock

Register the wireleass mac clock on rt2880. This is required by the wifi driver.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8006/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: add missing clk_set_rate() to clk.c

This function was missing causing make allmod to fail.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8005/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: allow manual memory override

RT5350 relies on the bootloader setting up the memc correctly. On some boards
the setup is incorrect leading to 32 MB being available but only 16 MB being
recognized. Allow these boards to manually override the memory range.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8004/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: add illegal access driver

These SoCs have a special irq that fires upon an illegal memmory access.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8003/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: add rt_sysc_m32 helper

We already have a read and write wrapper. This adds the missing mask wrapper.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8001/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: add a helper for reading the ECO version

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8000/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: add verbose pmu info

Print the PMU and LDO settings on boot.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/7999/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: lantiq: add missing spi clock on falcon SoC

Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8050/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: lantiq: the detection of the gpe clock is broken

The code to detect unfused SoCs was broken due to missing register masking.

Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8049/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: lantiq: copy the commandline from the devicetree

This is a regression caused by:
commit afb46f7996e91aeb36e07bc92cf96e8045bec00e
Author: Rob Herring <robh@kernel.org>
Date:   Wed Apr 2 19:07:24 2014 -0500
mips: ralink: convert to use unflatten_and_copy_device_tree

Make the of init code reuse the cmdline defined inside the dts.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8048/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: lantiq: move eiu init after irq_domain register

The eiu init failed as the irq_domain was not yet available.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8047/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: lantiq: export soc type

The voice and dsl drivers need to know which SoC we are running on.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/8046/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: lantiq: add support for xrx200 firmware depending on soc type

VR9 needs different firmware files for the various phy/soc revisions. Some
boards are ship with older and newer SoC revisions. To be able to boot a single
image on all versions we need to define both firmware files inside the
devicetree.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8045/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: lantiq: reboot gphy on restart

A reboot sometimes lead to a none working phy. An explicit reboot fixes the
problem.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8044/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: lantiq: add reset-controller api support

Add a reset-controller binding for the reset registers found on the lantiq
SoC.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8043/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: lantiq: handle vmmc memory reservation

The Lantiq SoCs have a 2nd mips core called "voice mips macro core (vmmc)"
which is used to run the voice firmware. This driver allows us to register
a chunk of memory that the voice driver can later use for the 2nd core.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8042/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Alchemy: Remove direct access to prepare_count field of struct clk

Replacing it with a call to __clk_is_prepared(), which isn't entirely
equivalent but in practice shouldn't matter.

Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8120/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

clocksource: mips-gic: Bump up rating of GIC timer

Bump up the rating of the GIC timer so that it gets prioritized
over the CP0 timer.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8141/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

clocksource: mips-gic: Use clockevents_config_and_register

Use clockevents_config_and_register to setup the clock_event_device
based on frequency and min/max ticks instead of doing it ourselves.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8140/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

clocksource: mips-gic: Use CPU notifiers to setup the timer

Instead of requiring an explicit call to gic_clockevent_init in the SMP
startup path, use CPU notifiers to register and enable the GIC timer on
CPU startup.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8139/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

clocksource: mips-gic: Use percpu_dev_id

Since the GIC timer IRQ is a percpu IRQ, we can use percpu_dev_id
to pass the IRQ handler the correct clock_event_device.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8138/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

clocksource: mips-gic: Remove gic_event_handler

Remove gic_event_handler since it is completely unnecessary.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8136/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

clocksource: mips-gic: Move gic_frequency to clocksource driver

There's no reason for gic_frequency to be global any more and it
certainly doesn't belong in the GIC irqchip driver, so move it to
the GIC clocksource driver.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8137/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

clocksource: mips-gic: Staticize local symbols

There are a number of variables and functions which are unnecessarily
global.  Mark them static.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8135/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

clocksource: mips-gic: Combine with GIC clockevent driver

Combine the GIC clocksource driver with the GIC clockevent driver from
arch/mips/kernel/cevt-gic.c and remove the clockevent driver's separate
Kconfig symbol.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8132/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Move GIC clocksource driver to drivers/clocksource/

Move the GIC clocksource driver to drivers/clocksource/mips-gic-timer.c.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8133/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Use GIC_SH_WEDGE_{SET,CLR} macros

Use the GIC_SH_WEDGE_{SET,CLR} macros provided by mips-gic.h.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8134/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Remove gic_{pending,itrmask}_regs

There's no reason for the pending and masked interrupt bitmasks
to be global.  Just declare them on the stack in gic_get_int()
since they only consume (256*2)/8 = 64 bytes.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8131/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Clean up #includes

Sort the #includes and remove those which are unnecessary.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8130/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Clean up header file

Remove duplicate #defines and unnecessary #includes, fix parenthesization,
and re-order register definitions in ascending order.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8128/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MAINTAINERS: Add entry for bcm63xx/bcm33xx UDC gadget driver

This hardware shows up on the newly-supported BCM3384 cable chip, as well
as several old BCM63xx DSL chips.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8172/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MAINTAINERS: Add entry for BCM33xx cable chips

Add myself as a maintainer for the new BCM3384 board support code.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8171/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: bcm3384: Initial commit of bcm3384 platform support

This supports SMP Linux running on the BCM3384 Zephyr (BMIPS5000)
application processor, with fully functional UART and USB 1.1/2.0.
Device Tree is used to configure the following items:

 - All peripherals
 - Early console base address
 - SMP or UP mode
 - MIPS counter frequency
 - Memory size / regions
 - DMA offset
 - Kernel command line

The DT-enabled bootloader and build instructions are posted at
https://github.com/Broadcom/aeolus

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8170/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Documentation: DT: Add "mti" vendor prefix

We have a bunch of platforms using "mti,cpu-interrupt-controller" but
the "mti" prefix isn't documented.  Fix this.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8169/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Documentation: DT: Add entries for BCM3384 and its peripherals

This covers the new "brcm,*" devices added in the upcoming bcm3384 commit.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8168/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Create a helper function for DT setup

A couple of platforms register two buses and call of_platform_populate().
Move this into a common function to reduce duplication.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8167/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Add PRId for BMIPS5200 (Whirlwind)

This is a dual core (quad thread) BMIPS5000.  It needs a little extra
code to boot the second core (CPU2/CPU3), but for now we can treat it the
same as a single core BMIPS5000.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8166/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Add special cache handling in c-r4k.c

BMIPS435x and BMIPS438x have a single shared L1 D$ and load/store unit,
so it isn't necessary to raise IPIs to keep both CPUs coherent.

BMIPS5000 has VIPT L1 caches that handle aliases in hardware, and its I$
fills from D$.  But a special sequence with 2 SYNCs and 32 NOPs is needed
to ensure coherency.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8165/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Let each platform customize the CPU1 IRQ mask

On some chips like bcm3384, "other stuff" gets wired up to CPU1's IE_IRQ1
input, generating spurious IRQs.  In this case we want the platform code
to be able to mask it off.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8163/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Select the appropriate L1_CACHE_SHIFT for 438x and 5000 CPUs

BMIPS438x has a 64-byte D$ line size and BMIPS5000 has a 128-byte L2
line size.  If L1_CACHE_SHIFT is undersized, DMA buffers will not be
cacheline-aligned and terrible things will happen.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8164/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Allow MIPS_CPU_SCACHE to be used with different line sizes

CONFIG_MIPS_CPU_SCACHE determines whether to build sc-mips.c.  However,
it is currently hardwired to use an L1_SHIFT of 6 (64 bytes).  Move the
L1_SHIFT selection into the CPU or SoC section so that other SoCs can
select different values.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8162/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Explicitly configure reset vectors prior to secondary boot

The secondary CPU's reset vector needs to be set to KSEG1 for a cold
boot (release from reset), or KSEG0 for a warm restart.  On a cold boot
KSEG0 may be unavailable (BMIPS4380), and on a warm restart KSEG1 may
be unavailable (XKS01 mode on 4380 or 5000).

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8161/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Mask off timer IRQs when hot-unplugging a CPU

CPU interrupts need to be disabled on a cpu being taken down.
When a cpu is hot-plugged out of the system the following sequence occurs.

On the CPU where the hotplug sequence was initiated:
    cpu_down
        _cpu_down {
            __cpu_notify(CPU_DOWN_PREPARE
            __stop_machine(take_cpu_down
                wait for cpu to run disable code.
            __cpu_die
        }

On the CPU  being disabled:
    take_cpu_down
        __cpu_disable {
            mp_ops->cpu_disable
                bmips_cpu_disable
                    clear_c0_status(IE_IRQ5) (added)
            cpu_notify(CPU_DYING...
        }

Before the cpu_notifier is called with CPU_DYING, all interrupts on the
dying cpu must be disabled.  This guarantees that before tick_notify is
called with the CPU_DYING event and sets the clock device pointer to
NULL, there can not be any more clock interrupts.

When this wasn't done, an unfortunately-timed timer interrupt sometimes
caused hangs immediately prior to system suspend:

    Debug PM is not enabled. To enable partial suspend, rebuild kernel with CONFIG_PM_DEBUG
    Pass 1 out of 1,PM: Syncing filesystems ... mode=none, tp1=done.
    1, flags=5, cycle_tp=, sleep=
    Freezing user space processes ... (elapsed 0.01 seconds) done.
    Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
    PM: suspend of devices complete after 54.199 msecs
    PM: late suspend of devices complete after 0.172 msecs
    Disabling non-boot CPUs ...
    SMP: CPU1 is offline
    INFO: rcu_sched detected stalls on CPUs/tasks: { 3} (detected by 0, t=62537 jiffies)
    Call Trace:
    [<804baa78>] dump_stack+0x8/0x34
    [<8008a2d8>] __rcu_pending+0x4b8/0x55c
    [<8008adf4>] rcu_check_callbacks+0x78/0x180
    [<80037830>] update_process_times+0x40/0x6c
    [<80072fe4>] tick_sched_timer+0x74/0xe4
    [<80050180>] __run_hrtimer.clone.30+0x64/0x140
    [<80051150>] hrtimer_interrupt+0x19c/0x4bc
    [<8000cdb8>] c0_compare_interrupt+0x50/0x88
    [<80081b18>] handle_irq_event_percpu+0x5c/0x2f4
    [<80086490>] handle_percpu_irq+0x8c/0xc0
    [<800811b4>] generic_handle_irq+0x34/0x54
    [<800067dc>] do_IRQ+0x18/0x2c
    [<8000375c>] plat_irq_dispatch+0xd0/0x128
    [<80004a04>] ret_from_irq+0x0/0x4
    [<80004c40>] r4k_wait+0x20/0x40
    [<80006b6c>] cpu_idle+0x98/0xf0
    [<805d3988>] start_kernel+0x424/0x440

Signed-off-by: Jon Fraser <jfraser@broadcom.com>
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8160/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Allow BMIPS3300 to utilize SMP ebase relocation code

BMIPS3300 processors do not have the hardware to support SMP, but with a
small tweak, the SMP ebase relocation code allows BMIPS3300-based
platforms to reuse the S2/S3 power management code from BMIPS4380-based
chips.  Normally this is as simple as adding one line to prom_init():

    board_ebase_setup = &bmips_ebase_setup;

Signed-off-by: Jon Fraser <jfraser@broadcom.com>
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8159/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Introduce helper function to change the reset vector

This will need to be called from a few different places, and the logic
is starting to get a bit hairy (with the need for IPIs, CPU bug
workarounds, and hazards).

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8158/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Align secondary boot sequence with latest firmware releases

On some older BMIPS5200 (dual core / quad thread) platforms, the
PROM code set up CPU2/CPU3 so they would be started through an NMI
instead of through the ACTION register.  But this was incompatible with
some power management features that were later added, so the scheme was
changed so that Linux is fully responsible for booting CPU2/CPU3.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8157/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

clk: ls1x: Update relationship among all clocks

- Add clock lookups for APB devices.
 - Update clock relationship to make it more exact and clear.
                                 _____
         _______________________|     |
 OSC ___/                       | MUX |___ XXX CLK
        \___ PLL ___ XXX DIV ___|     |
                                |_____|

Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: mturquette@linaro.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8026/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Loongson1B: Add a clockevent/clocksource using PWM Timer

This patch add a clockevent/clocksource using PWM Timer for Loongson1B,
which is based on earlier work by Tang, Haifeng.

Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8025/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Loongson1B: Some fixes/updates for LS1B

- Fix hanging ethernet issue of LS1B v2.0 by adding pbl field in plat data.
   (It seems that the MAC controller of LS1B v2.0 can only accept pbl=1)
 - Add GMAC1 support and setup MUX in terms of PHY mode.
 - Add CPUFreq support.
 - Add MUX Register Definitions.
 - Add PWM Register Definitions.
 - Update clock register bitfields according to the latest spec.
 - Update clock related stuff.

Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8024/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Loongson1B: Improve early printk

- Determine serial port for early printk according to kernel command line.
  - Move to 8250/16550 serial early printk driver.

Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8023/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Loongson1B: Fix reboot problem on LS1B

- Correct the header file of watchdog registers
 - Use ioremap_nocache() to access watchdog registers instead

Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8022/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: DMA: Explain the lack of special handling for R14000/R16000.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BCM47XX: Clean up nvram header

1) Move private defines to the .c file
2) Move SPROM helper to the sprom.c
3) Drop unused code
4) Rename magic to the NVRAM_MAGIC
5) Add const to the char pointer we never modify

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8289/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BCM47XX: Use mtd as an alternative way/API to get NVRAM content

NVRAM can be read using magic memory offset, but after all it's just a
flash partition. On platforms where NVRAM isn't needed early we can get
it using mtd subsystem.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8266/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Kconfig option to better exercise/debug hybrid FPRs

The hybrid FPR scheme exists to allow for compatibility between existing
FP32 code and newly compiled FP64A code. Such code should hopefully be
rare in the real world, and for the moment is difficult to come across.
All code except that built for the FP64 ABI can correctly execute using
the hybrid FPR scheme, so debugging the hybrid FPR implementation can
be eased by forcing all such code to use it. This is undesirable in
general due to the trap & emulate overhead of the hybrid FPR
implementation, but is a very useful option to have for debugging.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7680/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ELF: Set FP mode according to .MIPS.abiflags

This patch reads the .MIPS.abiflags section when it is present, and sets
the FP mode of the task accordingly. Any loaded ELF files which do not
contain a .MIPS.abiflags section will continue to observe the previous
behaviour, that is FR=1 if EF_MIPS_FP64 is set else FR=0.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7681/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ELF: Add definition for the .MIPS.abiflags section

New toolchains will generate a .MIPS.abiflags section, referenced by a
new PT_MIPS_ABIFLAGS program header. This section will provide
information about the requirements of the ELF, including the ISA level
the code is built for, the ASEs it requires, the size of various
registers and its expectations of the floating point mode. This patch
introduces a definition of the structure of this section and the program
header, for use in a subsequent patch.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7682/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Support for hybrid FPRs

Hybrid FPRs is a scheme where scalar FP registers are 64b wide, but
accesses to odd indexed single registers use bits 63:32 of the
preceeding even indexed 64b register. In this mode all FP code
except that built for the plain FP64 ABI can execute correctly. Most
notably a combination of FP64A & FP32 code can execute correctly,
allowing for existing FP32 binaries to be linked with new FP64A binaries
that can make use of 64 bit FP & MSA.

Hybrid FPRs are implemented by setting both the FR & FRE bits, trapping
& emulating single precision FP instructions (via Reserved Instruction
exceptions) whilst allowing others to execute natively. It therefore has
a penalty in terms of execution speed, and should only be used when no
fully native mode can be. As more binaries are recompiled to use either
the FPXX or FP64(A) ABIs, the need for hybrid FPRs should diminish.
However in the short to mid term it allows for a gradual transition
towards that world, rather than a complete ABI break which is not
feasible for some users & not desirable for many.

A task will be executed using the hybrid FPR scheme when its
TIF_HYBRID_FPREGS flag is set & TIF_32BIT_FPREGS is clear. A further
patch will set the flags as necessary, this patch simply adds the
infrastructure necessary for the hybrid FPR mode to work.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7683/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Ensure Config5.UFE is clear on boot

As is done for UFR, ensure that userland cannot directly manipulate the
mode by clearing the UFE bit during boot.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7677/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: detect presence of the FRE & UFR bits

Detect the presence of the Config5 FRE & UFE bits, as indicated by the
FREP bit in FPIR. Record this as a CPU option bit, and provide a
cpu_has_fre macro to ease checking of that option bit.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7678/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: define bits introduced for hybrid FPRs

Add definitions for the FRE & UFE bits in Config5, and the FREP bit in
FPIR. These bits are used to support a hybrid FPR scheme allowing a
mixture of FP32 & FP64 code to execute within a task.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7674/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

binfmt_elf: allow arch code to examine PT_LOPROC ... PT_HIPROC headers

MIPS is introducing new variants of its O32 ABI which differ in their
handling of floating point, in order to enable a gradual transition
towards a world where mips32 binaries can take advantage of new hardware
features only available when configured for certain FP modes. In order
to do this ELF binaries are being augmented with a new section that
indicates, amongst other things, the FP mode requirements of the binary.
The presence & location of such a section is indicated by a program
header in the PT_LOPROC ... PT_HIPROC range.

In order to allow the MIPS architecture code to examine the program
header & section in question, pass all program headers in this range
to an architecture-specific arch_elf_pt_proc function. This function
may return an error if the header is deemed invalid or unsuitable for
the system, in which case that error will be returned from
load_elf_binary and upwards through the execve syscall.

A means is required for the architecture code to make a decision once
it is known that all such headers have been seen, but before it is too
late to return from an execve syscall. For this purpose the
arch_check_elf function is added, and called once, after all PT_LOPROC
to PT_HIPROC headers have been passed to arch_elf_pt_proc but before
the code which invoked execve has been lost. This enables the
architecture code to make a decision based upon all the headers present
in an ELF binary and its interpreter, as is required to forbid
conflicting FP ABI requirements between an ELF & its interpreter.

In order to allow data to be stored throughout the calls to the above
functions, struct arch_elf_state is introduced.

Finally a variant of the SET_PERSONALITY macro is introduced which
accepts a pointer to the struct arch_elf_state, allowing it to act
based upon state observed from the architecture specific program
headers.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7679/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

binfmt_elf: load interpreter program headers earlier

Load the program headers of an ELF interpreter early enough in
load_elf_binary that they can be examined before it's too late to return
an error from an exec syscall. This patch does not perform any such
checking, it merely lays the groundwork for a further patch to do so.

No functional change is intended.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7675/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

binfmt_elf: Hoist ELF program header loading to a function

load_elf_binary & load_elf_interp both load program headers from an ELF
executable in the same way, duplicating the code. This patch introduces
a helper function (load_elf_phdrs) which performs this common task &
calls it from both load_elf_binary & load_elf_interp. In addition to
reducing code duplication, this is part of preparing to load the ELF
interpreter headers earlier such that they can be examined before it's
too late to return an error from an exec syscall.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7676/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Loongson-3: Add RS780/SBX00 HPET support

CPUFreq driver need external timer, so add hpet at first.

In Loongson 3, only Core-0 can receive external interrupt. As a result,
timekeeping cannot absolutely use HPET timer. We use a hybrid solution:
Core-0 use HPET as its clock event device, but other cores still use
MIPS; clock source is global and doesn't need interrupt, so use HPET.

Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/8329/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Loongson-3: Add oprofile support

Loongson-3 has two groups of performance counters, they are 4 sub-
registers of CP0's REG25. This patch add oprofile support.

REG25, sel 0: Perf Control of group 0;
REG25, sel 1: Perf Counter of group 0;
REG25, sel 2: Perf Control of group 1;
REG25, sel 3: Perf Counter of group 1.

Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/8328/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Loongson: Improve LEFI firmware interface

Machtypes of Loongson-3 machines become more and more, but there are
only small differences among different machtypes. Keeping a large table
of machtypes is very ugly and hard to extend. We found that the major
machtype differences are UARTs information (number of UARTs, UART IRQs,
UART clocks, etc.), platform devices (EC, temperature sensors, fan
controllers, etc.) and some workarounds (because of some CPU bugs or
mainboard bugs).

In this patch we improve the UEFI-like (LEFI) interface to make all
Loongson-3 machines use a same machtype "generic-loongson-machine".

Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/8324/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Loongson: Allow booting from any core

By offering Logical->Physical core id mapping, so as to reserve some
physical cores via mask. This allow booting from any core when core-0
has problems. Since the maximun cores supported by Loongson-3 is 16,
32-bit cpu_startup_core_id can be split to 16-bit cpu_startup_core_id
and 16-bit reserved_cores_mask for compatibility.

Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/8323/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Loongson-3: Add PHYS48_TO_HT40 support

The width of HT-bus is only 40-bit, but Loongson-3 has 48-bit physical
address. This implies only node-0's memory is DMAable because high bits
(Node ID) will lost. Fortunately, by configuring address windows in
firmware, we can extract 2bit Node ID (bit 44~47, only bit 44~45 used
now) from Loongson-3's 48-bit address space and embed it into 40-bit
(bit 37~38). Every NUMA node can do DMA now (however, maximum memory of
each node is reduced to 2^37 = 128GB).

Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/8321/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: R3000: Remove redundant parentheses

Signed-off-by: Isamu Mogi <isamu@leafytree.jp>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8292/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: R3000: Replace magic numbers with macros

Also include asm/mmu_context.h for ASID_MASK.

Signed-off-by: Isamu Mogi <isamu@leafytree.jp>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8291/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Remove __strlen_user().

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BCM47XX: Initialize bcma bus later (with mm available)

Initializaion with memory allocator available will be much simpler, this
will allow cleanup in the bcma code.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8234/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BCM47XX: Move SPROM fallback code into sprom.c

This is some general cleanup as well as preparing sprom.c to become a
standalone driver. We will need this for bcm53xx ARM arch support.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8232/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BCM47XX: Make bcma init NVRAM instead of bcm47xx polling it

This drops ssb/bcma dependency and will allow us to make it a standalone
driver.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/8233/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BCM47XX: Make ssb init NVRAM instead of bcm47xx polling it

This makes NVRAM code less bcm47xx/ssb specific allowing it to become a
standalone driver in the future. A similar patch for bcma will follow
when it's ready.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7612/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BCM47XX: Get rid of calls to KSEG1ADDR

We should be using ioremap_nocache helper which handles remaps in a
smarter way.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/7611/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Move gic.h to include/linux/irqchip/mips-gic.h

Now that the MIPS GIC irqchip lives in drivers/irqchip/, move
its header over to include/linux/irqchip/.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8129/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Use proper iomem accessors

Get rid of the ugly GICREAD/GICWRITE/GICBIS macros and use proper
iomem accessors instead.  Since the GIC registers are not directly
accessed outside of the GIC driver any more, make gic_base static
and move all the GIC register manipulation macros out of gic.h,
converting them to static inline functions.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8127/
Patchwork: https://patchwork.linux-mips.org/patch/8229/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Malta: Stop using GIC REG macros

Stop using the REG macros from gic.h and instead use proper iomem
accessors.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8126/
Patchwork: https://patchwork.linux-mips.org/patch/8227/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: SEAD3: Stop using GIC REG macros

Stop using the REG macros from gic.h and instead use proper iomem
accessors.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8125/
Patchwork: https://patchwork.linux-mips.org/patch/8228/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Export function to read counter width

Export the function gic_get_count_width to read the width of
the GIC global counter from GIC_SH_CONFIG.  Update the GIC
clocksource driver to use this new function.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8124/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Malta: Use gic_read_count() to read GIC timer

Instead of reading the GIC registers directly, use the interface the GIC
driver already exposes for reading the global timer.  Also get rid of
the unnecessary #ifdefs.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8123/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: SEAD3: Use generic plat_irq_dispatch

The generic plat_irq_dispatch provided in irq_cpu.c is sufficient for
dispatching interrupts on SEAD-3 in legacy and vectored interrupt modes.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7822/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Malta: Use generic plat_irq_dispatch

The generic plat_irq_dispatch provided in irq_cpu.c is sufficient for
dispatching interrupts on Malta in legacy and vectored interrupt modes.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7821/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Remove unnecessary globals

Now that all GIC interrupt routing and handling logic is in the GIC
driver itself, un-export variables/functions which are no longer used
outside the GIC driver.  This also allows us to remove gic_compare_int
and combine gic_get_int_mask with gic_get_int since these interfaces
are no longer used.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7820/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Support local interrupts

The MIPS GIC supports 7 local interrupts, 2 of which are the GIC
local watchdog and count/compare timer.  The remainder are CPU
interrupts which may optionally be re-routed through the GIC.
GIC hardware IRQs 0-6 are now used for local interrupts while
hardware IRQs 7+ are used for external (shared) interrupts.

Note that the 5 CPU interrupts may not be re-routable through
the GIC.  In that case mapping will fail and the vectors reported
in C0_IntCtl should be used instead.  gic_get_c0_compare_int() and
gic_get_c0_perfcount_int() will return the correct IRQ number to
use for the C0 timer and perfcounter interrupts based on the
routability of those interrupts through the GIC.

A separate irq_chip, with callbacks that mask/unmask the local
interrupt on all CPUs, is used for the C0 timer and performance
counter interrupts since all other platforms do not use the percpu
IRQ API for those interrupts.

Malta, SEAD-3, and the GIC clockevent driver have been updated
to use local interrupts and the R4K clockevent driver has been
updated to poll for C0 timer interrupts through the GIC when
the GIC is present.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7819/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Use separate edge/level irq_chips

GIC edge-triggered interrupts must be acknowledged by clearing the edge
detector via a write to GIC_SH_WEDGE.  Create a separate edge-triggered
irq_chip with the appropriate irq_ack() callback.  This also allows us
to get rid of gic_irq_flags.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7818/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Probe for number of external interrupts

Instead of requiring platforms to define the correct GIC_NUM_INTRS,
use the value reported in GIC_SH_CONFIG.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7817/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Stop using per-platform mapping tables

Now that the GIC properly uses IRQ domains, kill off the per-platform
routing tables that were used to make the GIC appear transparent.

This includes:
 - removing the mapping tables and the support for applying them,
 - moving GIC IPI support to the GIC driver,
 - properly routing the i8259 through the GIC on Malta, and
 - updating IRQ assignments on SEAD-3 when the GIC is present.

Platforms no longer will pass an interrupt mapping table to gic_init.
Instead, they will pass the CPU interrupt vector (2 - 7) that they
expect the GIC to route interrupts to.  Note that in EIC mode this
value is ignored and all GIC interrupts are routed to EIC vector 1.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7816/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Use IRQ domains

Use a simple IRQ domain for the MIPS GIC.  Remove the gic_platform_init
callback as it's no longer necessary for it to set the irqchip.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7811/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Fix gic_set_affinity() return value

If the online CPU check in gic_set_affinity() fails, return a proper
errno value instead of -1.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7814/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Implement irq_set_type callback

Implement an irq_set_type callback for the GIC which is used to set
the polarity and trigger type of GIC interrupts.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7810/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Remove platform irq_ack/irq_eoi callbacks

There's no need for platforms to have their own GIC irq_ack/irq_eoi
callbacks.  irq_ack need only clear the GIC's edge detector on
edge-triggered interrupts and there's no need at all for irq_eoi.
Also get rid of the mask_ack callback since it's not necessary either.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7809/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Move GIC to drivers/irqchip/

Move GIC irqchip support to drivers/irqchip/ and rename the Kconfig
option from IRQ_GIC to MIPS_GIC to avoid confusion with the ARM GIC.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7812/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Move MIPS_GIC_IRQ_BASE into platform irq.h

Define a generic MIPS_GIC_IRQ_BASE which should be suitable for all
current boards in <mach-generic/irq.h>.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7808/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Malta: Move MSC01 interrupt base

The GIC on Malta boards supports a total of 47 interrupts (40 shared
and 7 local) and is assigned a base of 24.  This overlaps with the
MSC01 interrupt assignments which have a base of 64, so move the MSC01
interrupt base back a bit to give the GIC some room.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7815/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>