Stefano Brivio [Wed, 16 Oct 2019 18:52:09 +0000 (20:52 +0200)]
ipv4: Return -ENETUNREACH if we can't create route but saddr is valid
[ Upstream commit
595e0651d0296bad2491a4a29a7a43eae6328b02 ]
...instead of -EINVAL. An issue was found with older kernel versions
while unplugging a NFS client with pending RPCs, and the wrong error
code here prevented it from recovering once link is back up with a
configured address.
Incidentally, this is not an issue anymore since commit
4f8943f80883
("SUNRPC: Replace direct task wakeups from softirq context"), included
in 5.2-rc7, had the effect of decoupling the forwarding of this error
by using SO_ERROR in xs_wake_error(), as pointed out by Benjamin
Coddington.
To the best of my knowledge, this isn't currently causing any further
issue, but the error code doesn't look appropriate anyway, and we
might hit this in other paths as well.
In detail, as analysed by Gonzalo Siero, once the route is deleted
because the interface is down, and can't be resolved and we return
-EINVAL here, this ends up, courtesy of inet_sk_rebuild_header(),
as the socket error seen by tcp_write_err(), called by
tcp_retransmit_timer().
In turn, tcp_write_err() indirectly calls xs_error_report(), which
wakes up the RPC pending tasks with a status of -EINVAL. This is then
seen by call_status() in the SUN RPC implementation, which aborts the
RPC call calling rpc_exit(), instead of handling this as a
potentially temporary condition, i.e. as a timeout.
Return -EINVAL only if the input parameters passed to
ip_route_output_key_hash_rcu() are actually invalid (this is the case
if the specified source address is multicast, limited broadcast or
all zeroes), but return -ENETUNREACH in all cases where, at the given
moment, the given source address doesn't allow resolving the route.
While at it, drop the initialisation of err to -ENETUNREACH, which
was added to __ip_route_output_key() back then by commit
0315e3827048 ("net: Fix behaviour of unreachable, blackhole and
prohibit routes"), but actually had no effect, as it was, and is,
overwritten by the fib_lookup() return code assignment, and anyway
ignored in all other branches, including the if (fl4->saddr) one:
I find this rather confusing, as it would look like -ENETUNREACH is
the "default" error, while that statement has no effect.
Also note that after commit
fc75fc8339e7 ("ipv4: dont create routes
on down devices"), we would get -ENETUNREACH if the device is down,
but -EINVAL if the source address is specified and we can't resolve
the route, and this appears to be rather inconsistent.
Reported-by: Stefan Walter <walteste@inf.ethz.ch>
Analysed-by: Benjamin Coddington <bcodding@redhat.com>
Analysed-by: Gonzalo Siero <gsierohu@redhat.com>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yi Li [Sat, 19 Oct 2019 03:20:08 +0000 (20:20 -0700)]
ocfs2: fix panic due to ocfs2_wq is null
commit
b918c43021baaa3648de09e19a4a3dd555a45f40 upstream.
mount.ocfs2 failed when reading ocfs2 filesystem superblock encounters
an error. ocfs2_initialize_super() returns before allocating ocfs2_wq.
ocfs2_dismount_volume() triggers the following panic.
Oct 15 16:09:27 cnwarekv-205120 kernel: On-disk corruption discovered.Please run fsck.ocfs2 once the filesystem is unmounted.
Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_read_locked_inode:537 ERROR: status = -30
Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_init_global_system_inodes:458 ERROR: status = -30
Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_init_global_system_inodes:491 ERROR: status = -30
Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_initialize_super:2313 ERROR: status = -30
Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_fill_super:1033 ERROR: status = -30
------------[ cut here ]------------
Oops: 0002 [#1] SMP NOPTI
CPU: 1 PID: 11753 Comm: mount.ocfs2 Tainted: G E
4.14.148-200.ckv.x86_64 #1
Hardware name: Sugon H320-G30/35N16-US, BIOS 0SSDX017 12/21/2018
task:
ffff967af0520000 task.stack:
ffffa5f05484000
RIP: 0010:mutex_lock+0x19/0x20
Call Trace:
flush_workqueue+0x81/0x460
ocfs2_shutdown_local_alloc+0x47/0x440 [ocfs2]
ocfs2_dismount_volume+0x84/0x400 [ocfs2]
ocfs2_fill_super+0xa4/0x1270 [ocfs2]
? ocfs2_initialize_super.isa.211+0xf20/0xf20 [ocfs2]
mount_bdev+0x17f/0x1c0
mount_fs+0x3a/0x160
Link: http://lkml.kernel.org/r/1571139611-24107-1-git-send-email-yili@winhong.com
Signed-off-by: Yi Li <yilikernel@gmail.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Deucher [Wed, 9 Oct 2019 18:12:37 +0000 (13:12 -0500)]
Revert "drm/radeon: Fix EEH during kexec"
[ Upstream commit
8d13c187c42e110625d60094668a8f778c092879 ]
This reverts commit
6f7fe9a93e6c09bf988c5059403f5f88e17e21e6.
This breaks some boards. Maybe just enable this on PPC for
now?
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=205147
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Song Liu [Mon, 14 Oct 2019 23:58:35 +0000 (16:58 -0700)]
md/raid0: fix warning message for parameter default_layout
[ Upstream commit
3874d73e06c9b9dc15de0b7382fc223986d75571 ]
The message should match the parameter, i.e. raid0.default_layout.
Fixes:
c84a1372df92 ("md/raid0: avoid RAID0 data corruption due to layout confusion.")
Cc: NeilBrown <neilb@suse.de>
Reported-by: Ivan Topolsky <doktor.yak@gmail.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jacob Keller [Fri, 27 Sep 2019 23:30:27 +0000 (16:30 -0700)]
namespace: fix namespace.pl script to support relative paths
[ Upstream commit
82fdd12b95727640c9a8233c09d602e4518e71f7 ]
The namespace.pl script does not work properly if objtree is not set to
an absolute path. The do_nm function is run from within the find
function, which changes directories.
Because of this, appending objtree, $File::Find::dir, and $source, will
return a path which is not valid from the current directory.
This used to work when objtree was set to an absolute path when using
"make namespacecheck". It appears to have not worked when calling
./scripts/namespace.pl directly.
This behavior was changed in
7e1c04779efd ("kbuild: Use relative path
for $(objtree)", 2014-05-14)
Rather than fixing the Makefile to set objtree to an absolute path, just
fix namespace.pl to work when srctree and objtree are relative. Also fix
the script to use an absolute path for these by default.
Use the File::Spec module for this purpose. It's been part of perl
5 since 5.005.
The curdir() function is used to get the current directory when the
objtree and srctree aren't set in the environment.
rel2abs() is used to convert possibly relative objtree and srctree
environment variables to absolute paths.
Finally, the catfile() function is used instead of string appending
paths together, since this is more robust when joining paths together.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Kai-Heng Feng [Fri, 4 Oct 2019 12:51:04 +0000 (20:51 +0800)]
r8152: Set macpassthru in reset_resume callback
[ Upstream commit
a54cdeeb04fc719e4c7f19d6e28dba7ea86cee5b ]
r8152 may fail to establish network connection after resume from system
suspend.
If the USB port connects to r8152 lost its power during system suspend,
the MAC address was written before is lost. The reason is that The MAC
address doesn't get written again in its reset_resume callback.
So let's set MAC address again in reset_resume callback. Also remove
unnecessary lock as no other locking attempt will happen during
reset_resume.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yizhuo [Tue, 1 Oct 2019 20:24:39 +0000 (13:24 -0700)]
net: hisilicon: Fix usage of uninitialized variable in function mdio_sc_cfg_reg_write()
[ Upstream commit
53de429f4e88f538f7a8ec2b18be8c0cd9b2c8e1 ]
In function mdio_sc_cfg_reg_write(), variable "reg_value" could be
uninitialized if regmap_read() fails. However, "reg_value" is used
to decide the control flow later in the if statement, which is
potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Christophe JAILLET [Tue, 10 Sep 2019 03:59:07 +0000 (05:59 +0200)]
mips: Loongson: Fix the link time qualifier of 'serial_exit()'
[ Upstream commit
25b69a889b638b0b7e51e2c4fe717a66bec0e566 ]
'exit' functions should be marked as __exit, not __init.
Fixes:
85cc028817ef ("mips: make loongsoon serial driver explicitly modular")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: chenhc@lemote.com
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: kernel-janitors@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Miaoqing Pan [Fri, 27 Sep 2019 02:03:16 +0000 (10:03 +0800)]
mac80211: fix txq null pointer dereference
[ Upstream commit
8ed31a264065ae92058ce54aa3cc8da8d81dc6d7 ]
If the interface type is P2P_DEVICE or NAN, read the file of
'/sys/kernel/debug/ieee80211/phyx/netdev:wlanx/aqm' will get a
NULL pointer dereference. As for those interface type, the
pointer sdata->vif.txq is NULL.
Unable to handle kernel NULL pointer dereference at virtual address
00000011
CPU: 1 PID: 30936 Comm: cat Not tainted 4.14.104 #1
task:
ffffffc0337e4880 task.stack:
ffffff800cd20000
PC is at ieee80211_if_fmt_aqm+0x34/0xa0 [mac80211]
LR is at ieee80211_if_fmt_aqm+0x34/0xa0 [mac80211]
[...]
Process cat (pid: 30936, stack limit = 0xffffff800cd20000)
[...]
[<
ffffff8000b7cd00>] ieee80211_if_fmt_aqm+0x34/0xa0 [mac80211]
[<
ffffff8000b7c414>] ieee80211_if_read+0x60/0xbc [mac80211]
[<
ffffff8000b7ccc4>] ieee80211_if_read_aqm+0x28/0x30 [mac80211]
[<
ffffff80082eff94>] full_proxy_read+0x2c/0x48
[<
ffffff80081eef00>] __vfs_read+0x2c/0xd4
[<
ffffff80081ef084>] vfs_read+0x8c/0x108
[<
ffffff80081ef494>] SyS_read+0x40/0x7c
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/1569549796-8223-1-git-send-email-miaoqing@codeaurora.org
[trim useless data from commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Miaoqing Pan [Thu, 26 Sep 2019 08:16:50 +0000 (16:16 +0800)]
nl80211: fix null pointer dereference
[ Upstream commit
b501426cf86e70649c983c52f4c823b3c40d72a3 ]
If the interface is not in MESH mode, the command 'iw wlanx mpath del'
will cause kernel panic.
The root cause is null pointer access in mpp_flush_by_proxy(), as the
pointer 'sdata->u.mesh.mpp_paths' is NULL for non MESH interface.
Unable to handle kernel NULL pointer dereference at virtual address
00000068
[...]
PC is at _raw_spin_lock_bh+0x20/0x5c
LR is at mesh_path_del+0x1c/0x17c [mac80211]
[...]
Process iw (pid: 4537, stack limit = 0xd83e0238)
[...]
[<
c021211c>] (_raw_spin_lock_bh) from [<
bf8c7648>] (mesh_path_del+0x1c/0x17c [mac80211])
[<
bf8c7648>] (mesh_path_del [mac80211]) from [<
bf6cdb7c>] (extack_doit+0x20/0x68 [compat])
[<
bf6cdb7c>] (extack_doit [compat]) from [<
c05c309c>] (genl_rcv_msg+0x274/0x30c)
[<
c05c309c>] (genl_rcv_msg) from [<
c05c25d8>] (netlink_rcv_skb+0x58/0xac)
[<
c05c25d8>] (netlink_rcv_skb) from [<
c05c2e14>] (genl_rcv+0x20/0x34)
[<
c05c2e14>] (genl_rcv) from [<
c05c1f90>] (netlink_unicast+0x11c/0x204)
[<
c05c1f90>] (netlink_unicast) from [<
c05c2420>] (netlink_sendmsg+0x30c/0x370)
[<
c05c2420>] (netlink_sendmsg) from [<
c05886d0>] (sock_sendmsg+0x70/0x84)
[<
c05886d0>] (sock_sendmsg) from [<
c0589f4c>] (___sys_sendmsg.part.3+0x188/0x228)
[<
c0589f4c>] (___sys_sendmsg.part.3) from [<
c058add4>] (__sys_sendmsg+0x4c/0x70)
[<
c058add4>] (__sys_sendmsg) from [<
c0208c80>] (ret_fast_syscall+0x0/0x44)
Code:
e2822c02 e2822001 e5832004 f590f000 (
e1902f9f)
---[ end trace
bbd717600f8f884d ]---
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Link: https://lore.kernel.org/r/1569485810-761-1-git-send-email-miaoqing@codeaurora.org
[trim useless data from commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ross Lagerwall [Fri, 27 Sep 2019 15:49:20 +0000 (16:49 +0100)]
xen/efi: Set nonblocking callbacks
[ Upstream commit
df359f0d09dc029829b66322707a2f558cb720f7 ]
Other parts of the kernel expect these nonblocking EFI callbacks to
exist and crash when running under Xen. Since the implementations of
xen_efi_set_variable() and xen_efi_query_variable_info() do not take any
locks, use them for the nonblocking callbacks too.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Oleksij Rempel [Mon, 30 Sep 2019 09:39:52 +0000 (11:39 +0200)]
MIPS: dts: ar9331: fix interrupt-controller size
[ Upstream commit
0889d07f3e4b171c453b2aaf2b257f9074cdf624 ]
It is two registers each of 4 byte.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Michal Vokáč [Thu, 26 Sep 2019 08:59:17 +0000 (10:59 +0200)]
net: dsa: qca8k: Use up to 7 ports for all operations
[ Upstream commit
7ae6d93c8f052b7a77ba56ed0f654e22a2876739 ]
The QCA8K family supports up to 7 ports. So use the existing
QCA8K_NUM_PORTS define to allocate the switch structure and limit all
operations with the switch ports.
This was not an issue until commit
0394a63acfe2 ("net: dsa: enable and
disable all ports") disabled all unused ports. Since the unused ports 7-11
are outside of the correct register range on this switch some registers
were rewritten with invalid content.
Fixes:
6b93fb46480a ("net-next: dsa: add new driver for qca8xxx family")
Fixes:
a0c02161ecfc ("net: dsa: variable number of ports")
Fixes:
0394a63acfe2 ("net: dsa: enable and disable all ports")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Peter Ujfalusi [Mon, 30 Sep 2019 08:54:50 +0000 (11:54 +0300)]
ARM: dts: am4372: Set memory bandwidth limit for DISPC
[ Upstream commit
f90ec6cdf674248dcad85bf9af6e064bf472b841 ]
Set memory bandwidth limit to filter out resolutions above 720p@60Hz to
avoid underflow errors due to the bandwidth needs of higher resolutions.
am43xx can not provide enough bandwidth to DISPC to correctly handle
'high' resolutions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Navid Emamdoost [Tue, 17 Sep 2019 22:47:12 +0000 (17:47 -0500)]
ieee802154: ca8210: prevent memory leak
[ Upstream commit
6402939ec86eaf226c8b8ae00ed983936b164908 ]
In ca8210_probe the allocated pdata needs to be assigned to
spi_device->dev.platform_data before calling ca8210_get_platform_data.
Othrwise when ca8210_get_platform_data fails pdata cannot be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Link: https://lore.kernel.org/r/20190917224713.26371-1-navid.emamdoost@gmail.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tony Lindgren [Tue, 24 Sep 2019 16:25:52 +0000 (09:25 -0700)]
ARM: OMAP2+: Fix missing reset done flag for am3 and am43
[ Upstream commit
8ad8041b98c665b6147e607b749586d6e20ba73a ]
For ti,sysc-omap4 compatible devices with no sysstatus register, we do have
reset done status available in the SOFTRESET bit that clears when the reset
is done. This is documented for example in am437x TRM for DMTIMER_TIOCP_CFG
register. The am335x TRM just says that SOFTRESET bit value 1 means reset is
ongoing, but it behaves the same way clearing after reset is done.
With the ti-sysc driver handling this automatically based on no sysstatus
register defined, we see warnings if SYSC_HAS_RESET_STATUS is missing in the
legacy platform data:
ti-sysc
48042000.target-module: sysc_flags
00000222 !=
00000022
ti-sysc
48044000.target-module: sysc_flags
00000222 !=
00000022
ti-sysc
48046000.target-module: sysc_flags
00000222 !=
00000022
...
Let's fix these warnings by adding SYSC_HAS_RESET_STATUS. Let's also
remove the useless parentheses while at it.
If it turns out we do have ti,sysc-omap4 compatible devices without a
working SOFTRESET bit we can set up additional quirk handling for it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Quinn Tran [Thu, 12 Sep 2019 18:09:06 +0000 (11:09 -0700)]
scsi: qla2xxx: Fix unbound sleep in fcport delete path.
[ Upstream commit
c3b6a1d397420a0fdd97af2f06abfb78adc370df ]
There are instances, though rare, where a LOGO request cannot be sent out
and the thread in free session done can wait indefinitely. Fix this by
putting an upper bound to sleep.
Link: https://lore.kernel.org/r/20190912180918.6436-3-hmadhani@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Xiang Chen [Sat, 7 Sep 2019 01:07:30 +0000 (09:07 +0800)]
scsi: megaraid: disable device when probe failed after enabled device
[ Upstream commit
70054aa39a013fa52eff432f2223b8bd5c0048f8 ]
For pci device, need to disable device when probe failed after enabled
device.
Link: https://lore.kernel.org/r/1567818450-173315-1-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Stanley Chu [Wed, 18 Sep 2019 04:20:38 +0000 (12:20 +0800)]
scsi: ufs: skip shutdown if hba is not powered
[ Upstream commit
f51913eef23f74c3bd07899dc7f1ed6df9e521d8 ]
In some cases, hba may go through shutdown flow without successful
initialization and then make system hang.
For example, if ufshcd_change_power_mode() gets error and leads to
ufshcd_hba_exit() to release resources of the host, future shutdown flow
may hang the system since the host register will be accessed in unpowered
state.
To solve this issue, simply add checking to skip shutdown for above kind of
situation.
Link: https://lore.kernel.org/r/1568780438-28753-1-git-send-email-stanley.chu@mediatek.com
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Acked-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Greg Kroah-Hartman [Thu, 17 Oct 2019 20:44:04 +0000 (13:44 -0700)]
Linux 4.14.150
Dave Chinner [Fri, 11 May 2018 04:50:23 +0000 (21:50 -0700)]
xfs: clear sb->s_fs_info on mount failure
commit
c9fbd7bbc23dbdd73364be4d045e5d3612cf6e82 upstream.
We recently had an oops reported on a 4.14 kernel in
xfs_reclaim_inodes_count() where sb->s_fs_info pointed to garbage
and so the m_perag_tree lookup walked into lala land.
Essentially, the machine was under memory pressure when the mount
was being run, xfs_fs_fill_super() failed after allocating the
xfs_mount and attaching it to sb->s_fs_info. It then cleaned up and
freed the xfs_mount, but the sb->s_fs_info field still pointed to
the freed memory. Hence when the superblock shrinker then ran
it fell off the bad pointer.
With the superblock shrinker problem fixed at teh VFS level, this
stale s_fs_info pointer is still a problem - we use it
unconditionally in ->put_super when the superblock is being torn
down, and hence we can still trip over it after a ->fill_super
call failure. Hence we need to clear s_fs_info if
xfs-fs_fill_super() fails, and we need to check if it's valid in
the places it can potentially be dereferenced after a ->fill_super
failure.
Signed-Off-By: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Ajay Kaher <akaher@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Janakarajan Natarajan [Mon, 7 Oct 2019 19:00:22 +0000 (19:00 +0000)]
x86/asm: Fix MWAITX C-state hint value
commit
454de1e7d970d6bc567686052329e4814842867c upstream.
As per "AMD64 Architecture Programmer's Manual Volume 3: General-Purpose
and System Instructions", MWAITX EAX[7:4]+1 specifies the optional hint
of the optimized C-state. For C0 state, EAX[7:4] should be set to 0xf.
Currently, a value of 0xf is set for EAX[3:0] instead of EAX[7:4]. Fix
this by changing MWAITX_DISABLE_CSTATES from 0xf to 0xf0.
This hasn't had any implications so far because setting reserved bits in
EAX is simply ignored by the CPU.
[ bp: Fixup comment in delay_mwaitx() and massage. ]
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Frederic Weisbecker <frederic@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "x86@kernel.org" <x86@kernel.org>
Cc: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20191007190011.4859-1-Janakarajan.Natarajan@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steven Rostedt (VMware) [Fri, 11 Oct 2019 22:19:17 +0000 (18:19 -0400)]
tracing: Get trace_array reference for available_tracers files
commit
194c2c74f5532e62c218adeb8e2b683119503907 upstream.
As instances may have different tracers available, we need to look at the
trace_array descriptor that shows the list of the available tracers for the
instance. But there's a race between opening the file and an admin
deleting the instance. The trace_array_get() needs to be called before
accessing the trace_array.
Cc: stable@vger.kernel.org
Fixes:
607e2ea167e56 ("tracing: Set up infrastructure to allow tracers for instances")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steven Rostedt (VMware) [Fri, 11 Oct 2019 21:56:57 +0000 (17:56 -0400)]
ftrace: Get a reference counter for the trace_array on filter files
commit
9ef16693aff8137faa21d16ffe65bb9832d24d71 upstream.
The ftrace set_ftrace_filter and set_ftrace_notrace files are specific for
an instance now. They need to take a reference to the instance otherwise
there could be a race between accessing the files and deleting the instance.
It wasn't until the :mod: caching where these file operations started
referencing the trace_array directly.
Cc: stable@vger.kernel.org
Fixes:
673feb9d76ab3 ("ftrace: Add :mod: caching infrastructure to trace_array")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Srivatsa S. Bhat (VMware) [Thu, 10 Oct 2019 18:51:01 +0000 (11:51 -0700)]
tracing/hwlat: Don't ignore outer-loop duration when calculating max_latency
commit
fc64e4ad80d4b72efce116f87b3174f0b7196f8e upstream.
max_latency is intended to record the maximum ever observed hardware
latency, which may occur in either part of the loop (inner/outer). So
we need to also consider the outer-loop sample when updating
max_latency.
Link: http://lkml.kernel.org/r/157073345463.17189.18124025522664682811.stgit@srivatsa-ubuntu
Fixes:
e7c15cd8a113 ("tracing: Added hardware latency tracer")
Cc: stable@vger.kernel.org
Signed-off-by: Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Srivatsa S. Bhat (VMware) [Thu, 10 Oct 2019 18:50:46 +0000 (11:50 -0700)]
tracing/hwlat: Report total time spent in all NMIs during the sample
commit
98dc19c11470ee6048aba723d77079ad2cda8a52 upstream.
nmi_total_ts is supposed to record the total time spent in *all* NMIs
that occur on the given CPU during the (active portion of the)
sampling window. However, the code seems to be overwriting this
variable for each NMI, thereby only recording the time spent in the
most recent NMI. Fix it by accumulating the duration instead.
Link: http://lkml.kernel.org/r/157073343544.17189.13911783866738671133.stgit@srivatsa-ubuntu
Fixes:
7b2c86250122 ("tracing: Add NMI tracing in hwlat detector")
Cc: stable@vger.kernel.org
Signed-off-by: Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Tue, 1 Oct 2019 08:49:08 +0000 (10:49 +0200)]
media: stkwebcam: fix runtime PM after driver unbind
commit
30045f2174aab7fb4db7a9cf902d0aa6c75856a7 upstream.
Since commit
c2b71462d294 ("USB: core: Fix bug caused by duplicate
interface PM usage counter") USB drivers must always balance their
runtime PM gets and puts, including when the driver has already been
unbound from the interface.
Leaving the interface with a positive PM usage counter would prevent a
later bound driver from suspending the device.
Note that runtime PM has never actually been enabled for this driver
since the support_autosuspend flag in its usb_driver struct is not set.
Fixes:
c2b71462d294 ("USB: core: Fix bug caused by duplicate interface PM usage counter")
Cc: stable <stable@vger.kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191001084908.2003-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Al Viro [Sun, 15 Sep 2019 16:12:39 +0000 (12:12 -0400)]
Fix the locking in dcache_readdir() and friends
commit
d4f4de5e5ef8efde85febb6876cd3c8ab1631999 upstream.
There are two problems in dcache_readdir() - one is that lockless traversal
of the list needs non-trivial cooperation of d_alloc() (at least a switch
to list_add_rcu(), and probably more than just that) and another is that
it assumes that no removal will happen without the directory locked exclusive.
Said assumption had always been there, never had been stated explicitly and
is violated by several places in the kernel (devpts and selinuxfs).
* replacement of next_positive() with different calling conventions:
it returns struct list_head * instead of struct dentry *; the latter is
passed in and out by reference, grabbing the result and dropping the original
value.
* scan is under ->d_lock. If we run out of timeslice, cursor is moved
after the last position we'd reached and we reschedule; then the scan continues
from that place. To avoid livelocks between multiple lseek() (with cursors
getting moved past each other, never reaching the real entries) we always
skip the cursors, need_resched() or not.
* returned list_head * is either ->d_child of dentry we'd found or
->d_subdirs of parent (if we got to the end of the list).
* dcache_readdir() and dcache_dir_lseek() switched to new helper.
dcache_readdir() always holds a reference to dentry passed to dir_emit() now.
Cursor is moved to just before the entry where dir_emit() has failed or into
the very end of the list, if we'd run out.
* move_cursor() eliminated - it had sucky calling conventions and
after fixing that it became simply list_move() (in lseek and scan_positives)
or list_move_tail() (in readdir).
All operations with the list are under ->d_lock now, and we do not
depend upon having all file removals done with parent locked exclusive
anymore.
Cc: stable@vger.kernel.org
Reported-by: "zhengbin (A)" <zhengbin13@huawei.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Burton [Thu, 10 Oct 2019 18:54:03 +0000 (18:54 +0000)]
MIPS: Disable Loongson MMI instructions for kernel build
commit
2f2b4fd674cadd8c6b40eb629e140a14db4068fd upstream.
GCC 9.x automatically enables support for Loongson MMI instructions when
using some -march= flags, and then errors out when -msoft-float is
specified with:
cc1: error: ‘-mloongson-mmi’ must be used with ‘-mhard-float’
The kernel shouldn't be using these MMI instructions anyway, just as it
doesn't use floating point instructions. Explicitly disable them in
order to fix the build with GCC 9.x.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes:
3702bba5eb4f ("MIPS: Loongson: Add GCC 4.4 support for Loongson2E")
Fixes:
6f7a251a259e ("MIPS: Loongson: Add basic Loongson 2F support")
Fixes:
5188129b8c9f ("MIPS: Loongson-3: Improve -march option and move it to Platform")
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: stable@vger.kernel.org # v2.6.32+
Cc: linux-mips@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trond Myklebust [Mon, 30 Sep 2019 18:02:56 +0000 (14:02 -0400)]
NFS: Fix O_DIRECT accounting of number of bytes read/written
commit
031d73ed768a40684f3ca21992265ffdb6a270bf upstream.
When a series of O_DIRECT reads or writes are truncated, either due to
eof or due to an error, then we should return the number of contiguous
bytes that were received/sent starting at the offset specified by the
application.
Currently, we are failing to correctly check contiguity, and so we're
failing the generic/465 in xfstests when the race between the read
and write RPCs causes the file to get extended while the 2 reads are
outstanding. If the first read RPC call wins the race and returns with
eof set, we should treat the second read RPC as being truncated.
Reported-by: Su Yanjun <suyj.fnst@cn.fujitsu.com>
Fixes:
1ccbad9f9f9bd ("nfs: fix DIO good bytes calculation")
Cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Josef Bacik [Mon, 30 Sep 2019 20:27:25 +0000 (16:27 -0400)]
btrfs: fix incorrect updating of log root tree
commit
4203e968947071586a98b5314fd7ffdea3b4f971 upstream.
We've historically had reports of being unable to mount file systems
because the tree log root couldn't be read. Usually this is the "parent
transid failure", but could be any of the related errors, including
"fsid mismatch" or "bad tree block", depending on which block got
allocated.
The modification of the individual log root items are serialized on the
per-log root root_mutex. This means that any modification to the
per-subvol log root_item is completely protected.
However we update the root item in the log root tree outside of the log
root tree log_mutex. We do this in order to allow multiple subvolumes
to be updated in each log transaction.
This is problematic however because when we are writing the log root
tree out we update the super block with the _current_ log root node
information. Since these two operations happen independently of each
other, you can end up updating the log root tree in between writing out
the dirty blocks and setting the super block to point at the current
root.
This means we'll point at the new root node that hasn't been written
out, instead of the one we should be pointing at. Thus whatever garbage
or old block we end up pointing at complains when we mount the file
system later and try to replay the log.
Fix this by copying the log's root item into a local root item copy.
Then once we're safely under the log_root_tree->log_mutex we update the
root item in the log_root_tree. This way we do not modify the
log_root_tree while we're committing it, fixing the problem.
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Chris Mason <clm@fb.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andreas Klinger [Mon, 9 Sep 2019 12:37:21 +0000 (14:37 +0200)]
iio: adc: hx711: fix bug in sampling of data
[ Upstream commit
4043ecfb5fc4355a090111e14faf7945ff0fdbd5 ]
Fix bug in sampling function hx711_cycle() when interrupt occures while
PD_SCK is high. If PD_SCK is high for at least 60 us power down mode of
the sensor is entered which in turn leads to a wrong measurement.
Switch off interrupts during a PD_SCK high period and move query of DOUT
to the latest point of time which is at the end of PD_SCK low period.
This bug exists in the driver since it's initial addition. The more
interrupts on the system the higher is the probability that it happens.
Fixes:
c3b2fdd0ea7e ("iio: adc: hx711: Add IIO driver for AVIA HX711")
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Andreas Klinger [Tue, 10 Jul 2018 18:19:03 +0000 (20:19 +0200)]
iio: hx711: add delay until DOUT is ready
[ Upstream commit
461631face58054c72b1f1453f2d66d71b1974e7 ]
On a system with parasitic capacitance it turned out that DOUT is not ready
after 100 ns after PD_SCK has raised. A measurement showed almost 1000 ns
until DOUT has reached its correct value.
With this patch its now possible to wait until data is ready.
The wait time should not be higher than the maximum PD_SCK high time which
is corresponding to the datasheet 50000 ns.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Navid Emamdoost [Mon, 30 Sep 2019 03:09:45 +0000 (22:09 -0500)]
Staging: fbtft: fix memory leak in fbtft_framebuffer_alloc
[ Upstream commit
5bdea6060618cfcf1459dca137e89aee038ac8b9 ]
In fbtft_framebuffer_alloc the error handling path should take care of
releasing frame buffer after it is allocated via framebuffer_alloc, too.
Therefore, in two failure cases the goto destination is changed to
address this issue.
Fixes:
c296d5f9957c ("staging: fbtft: core support")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190930030949.28615-1-navid.emamdoost@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Bartosz Golaszewski [Mon, 14 Oct 2019 16:10:24 +0000 (18:10 +0200)]
gpiolib: don't clear FLAG_IS_OUT when emulating open-drain/open-source
[ Upstream commit
e735244e2cf068f98b6384681a38993e0517a838 ]
When emulating open-drain/open-source by not actively driving the output
lines - we're simply changing their mode to input. This is wrong as it
will then make it impossible to change the value of such line - it's now
considered to actually be in input mode. If we want to still use the
direction_input() callback for simplicity then we need to set FLAG_IS_OUT
manually in gpiod_direction_output() and not clear it in
gpio_set_open_drain_value_commit() and
gpio_set_open_source_value_commit().
Fixes:
c663e5f56737 ("gpio: support native single-ended hardware drivers")
Cc: stable@vger.kernel.org
Reported-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[Bartosz: backported to v4.14]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Brian Norris [Mon, 30 Sep 2019 21:45:22 +0000 (14:45 -0700)]
firmware: google: increment VPD key_len properly
[ Upstream commit
442f1e746e8187b9deb1590176f6b0ff19686b11 ]
Commit
4b708b7b1a2c ("firmware: google: check if size is valid when
decoding VPD data") adds length checks, but the new vpd_decode_entry()
function botched the logic -- it adds the key length twice, instead of
adding the key and value lengths separately.
On my local system, this means vpd.c's vpd_section_create_attribs() hits
an error case after the first attribute it parses, since it's no longer
looking at the correct offset. With this patch, I'm back to seeing all
the correct attributes in /sys/firmware/vpd/...
Fixes:
4b708b7b1a2c ("firmware: google: check if size is valid when decoding VPD data")
Cc: <stable@vger.kernel.org>
Cc: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Link: https://lore.kernel.org/r/20190930214522.240680-1-briannorris@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Michal Hocko [Mon, 7 Oct 2019 00:58:19 +0000 (17:58 -0700)]
kernel/sysctl.c: do not override max_threads provided by userspace
commit
b0f53dbc4bc4c371f38b14c391095a3bb8a0bb40 upstream.
Partially revert
16db3d3f1170 ("kernel/sysctl.c: threads-max observe
limits") because the patch is causing a regression to any workload which
needs to override the auto-tuning of the limit provided by kernel.
set_max_threads is implementing a boot time guesstimate to provide a
sensible limit of the concurrently running threads so that runaways will
not deplete all the memory. This is a good thing in general but there
are workloads which might need to increase this limit for an application
to run (reportedly WebSpher MQ is affected) and that is simply not
possible after the mentioned change. It is also very dubious to
override an admin decision by an estimation that doesn't have any direct
relation to correctness of the kernel operation.
Fix this by dropping set_max_threads from sysctl_max_threads so any
value is accepted as long as it fits into MAX_THREADS which is important
to check because allowing more threads could break internal robust futex
restriction. While at it, do not use MIN_THREADS as the lower boundary
because it is also only a heuristic for automatic estimation and admin
might have a good reason to stop new threads to be created even when
below this limit.
This became more severe when we switched x86 from 4k to 8k kernel
stacks. Starting since
6538b8ea886e ("x86_64: expand kernel stack to
16K") (3.16) we use THREAD_SIZE_ORDER = 2 and that halved the auto-tuned
value.
In the particular case
3.12
kernel.threads-max = 515561
4.4
kernel.threads-max = 200000
Neither of the two values is really insane on 32GB machine.
I am not sure we want/need to tune the max_thread value further. If
anything the tuning should be removed altogether if proven not useful in
general. But we definitely need a way to override this auto-tuning.
Link: http://lkml.kernel.org/r/20190922065801.GB18814@dhcp22.suse.cz
Fixes:
16db3d3f1170 ("kernel/sysctl.c: threads-max observe limits")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pavel Shilovsky [Mon, 30 Sep 2019 17:06:20 +0000 (10:06 -0700)]
CIFS: Force reval dentry if LOOKUP_REVAL flag is set
commit
0b3d0ef9840f7be202393ca9116b857f6f793715 upstream.
Mark inode for force revalidation if LOOKUP_REVAL flag is set.
This tells the client to actually send a QueryInfo request to
the server to obtain the latest metadata in case a directory
or a file were changed remotely. Only do that if the client
doesn't have a lease for the file to avoid unneeded round
trips to the server.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pavel Shilovsky [Mon, 30 Sep 2019 17:06:19 +0000 (10:06 -0700)]
CIFS: Force revalidate inode when dentry is stale
commit
c82e5ac7fe3570a269c0929bf7899f62048e7dbc upstream.
Currently the client indicates that a dentry is stale when inode
numbers or type types between a local inode and a remote file
don't match. If this is the case attributes is not being copied
from remote to local, so, it is already known that the local copy
has stale metadata. That's why the inode needs to be marked for
revalidation in order to tell the VFS to lookup the dentry again
before openning a file. This prevents unexpected stale errors
to be returned to the user space when openning a file.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pavel Shilovsky [Mon, 30 Sep 2019 17:06:18 +0000 (10:06 -0700)]
CIFS: Gracefully handle QueryInfo errors during open
commit
30573a82fb179420b8aac30a3a3595aa96a93156 upstream.
Currently if the client identifies problems when processing
metadata returned in CREATE response, the open handle is being
leaked. This causes multiple problems like a file missing a lease
break by that client which causes high latencies to other clients
accessing the file. Another side-effect of this is that the file
can't be deleted.
Fix this by closing the file after the client hits an error after
the file was opened and the open descriptor wasn't returned to
the user space. Also convert -ESTALE to -EOPENSTALE to allow
the VFS to revalidate a dentry and retry the open.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steve MacLean [Sat, 28 Sep 2019 01:41:18 +0000 (01:41 +0000)]
perf inject jit: Fix JIT_CODE_MOVE filename
commit
b59711e9b0d22fd47abfa00602fd8c365cdd3ab7 upstream.
During perf inject --jit, JIT_CODE_MOVE records were injecting MMAP records
with an incorrect filename. Specifically it was missing the ".so" suffix.
Further the JIT_CODE_LOAD record were silently truncating the
jr->load.code_index field to 32 bits before generating the filename.
Make both records emit the same filename based on the full 64 bit
code_index field.
Fixes:
9b07e27f88b9 ("perf inject: Add jitdump mmap injection support")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Steve MacLean <Steve.MacLean@Microsoft.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Brian Robbins <brianrob@microsoft.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Eric Saint-Etienne <eric.saint.etienne@oracle.com>
Cc: John Keeping <john@metanate.com>
Cc: John Salem <josalem@microsoft.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom McDonald <thomas.mcdonald@microsoft.com>
Link: http://lore.kernel.org/lkml/BN8PR21MB1362FF8F127B31DBF4121528F7800@BN8PR21MB1362.namprd21.prod.outlook.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ian Rogers [Thu, 26 Sep 2019 22:00:18 +0000 (15:00 -0700)]
perf llvm: Don't access out-of-scope array
commit
7d4c85b7035eb2f9ab217ce649dcd1bfaf0cacd3 upstream.
The 'test_dir' variable is assigned to the 'release' array which is
out-of-scope 3 lines later.
Extend the scope of the 'release' array so that an out-of-scope array
isn't accessed.
Bug detected by clang's address sanitizer.
Fixes:
07bc5c699a3d ("perf tools: Make fetch_kernel_version() publicly available")
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lore.kernel.org/lkml/20190926220018.25402-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ard Biesheuvel [Wed, 2 Oct 2019 16:58:59 +0000 (18:58 +0200)]
efivar/ssdt: Don't iterate over EFI vars if no SSDT override was specified
commit
c05f8f92b701576b615f30aac31fabdc0648649b upstream.
The kernel command line option efivar_ssdt= allows the name to be
specified of an EFI variable containing an ACPI SSDT table that should
be loaded into memory by the OS, and treated as if it was provided by
the firmware.
Currently, that code will always iterate over the EFI variables and
compare each name with the provided name, even if the command line
option wasn't set to begin with.
So bail early when no variable name was provided. This works around a
boot regression on the 2012 Mac Pro, as reported by Scott.
Tested-by: Scott Talbert <swt@techie.net>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org> # v4.9+
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Dave Young <dyoung@redhat.com>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Matthew Garrett <mjg59@google.com>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Cc: linux-integrity@vger.kernel.org
Fixes:
475fb4e8b2f4 ("efi / ACPI: load SSTDs from EFI variables")
Link: https://lkml.kernel.org/r/20191002165904.8819-3-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Frey [Thu, 19 Sep 2019 22:54:18 +0000 (15:54 -0700)]
iio: light: opt3001: fix mutex unlock race
commit
82f3015635249a8c8c45bac303fd84905066f04f upstream.
When an end-of-conversion interrupt is received after performing a
single-shot reading of the light sensor, the driver was waking up the
result ready queue before checking opt->ok_to_ignore_lock to determine
if it should unlock the mutex. The problem occurred in the case where
the other thread woke up and changed the value of opt->ok_to_ignore_lock
to false prior to the interrupt thread performing its read of the
variable. In this case, the mutex would be unlocked twice.
Signed-off-by: David Frey <dpfrey@gmail.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Fixes:
94a9b7b1809f ("iio: light: add support for TI's opt3001 light sensor")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Sun, 15 Sep 2019 18:53:42 +0000 (20:53 +0200)]
iio: adc: axp288: Override TS pin bias current for some models
commit
972917419a0ba25afbf69d5d8c9fa644d676f887 upstream.
Since commit
9bcf15f75cac ("iio: adc: axp288: Fix TS-pin handling") we
preserve the bias current set by the firmware at boot. This fixes issues
we were seeing on various models, but it seems our old hardcoded 80ųA bias
current was working around a firmware bug on at least one model laptop.
In order to both have our cake and eat it, this commit adds a dmi based
list of models where we need to override the firmware set bias current and
adds the one model we now know needs this to it: The Lenovo Ideapad 100S
(11 inch version).
Fixes:
9bcf15f75cac ("iio: adc: axp288: Fix TS-pin handling")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=203829
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marco Felsch [Tue, 17 Sep 2019 16:09:23 +0000 (18:09 +0200)]
iio: adc: ad799x: fix probe error handling
commit
c62dd44901cfff12acc5792bf3d2dec20bcaf392 upstream.
Since commit
0f7ddcc1bff1 ("iio:adc:ad799x: Write default config on probe
and reset alert status on probe") the error path is wrong since it
leaves the vref regulator on. Fix this by disabling both regulators.
Fixes:
0f7ddcc1bff1 ("iio:adc:ad799x: Write default config on probe and reset alert status on probe")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Navid Emamdoost [Fri, 4 Oct 2019 20:03:15 +0000 (15:03 -0500)]
staging: vt6655: Fix memory leak in vt6655_probe
commit
80b15db5e1e9c3300de299b2d43d1aafb593e6ac upstream.
In vt6655_probe, if vnt_init() fails the cleanup code needs to be called
like other error handling cases. The call to device_free_info() is
added.
Fixes:
67013f2c0e58 ("staging: vt6655: mac80211 conversion add main mac80211 functions")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191004200319.22394-1-navid.emamdoost@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Wed, 9 Oct 2019 15:38:47 +0000 (17:38 +0200)]
USB: legousbtower: fix use-after-free on release
commit
726b55d0e22ca72c69c947af87785c830289ddbc upstream.
The driver was accessing its struct usb_device in its release()
callback without holding a reference. This would lead to a
use-after-free whenever the device was disconnected while the character
device was still open.
Fixes:
fef526cae700 ("USB: legousbtower: remove custom debug macro")
Cc: stable <stable@vger.kernel.org> # 3.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191009153848.8664-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 19 Sep 2019 08:30:39 +0000 (10:30 +0200)]
USB: legousbtower: fix open after failed reset request
commit
0b074f6986751361ff442bc1127c1648567aa8d6 upstream.
The driver would return with a nonzero open count in case the reset
control request failed. This would prevent any further attempts to open
the char dev until the device was disconnected.
Fix this by incrementing the open count only on successful open.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190919083039.30898-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 19 Sep 2019 08:30:38 +0000 (10:30 +0200)]
USB: legousbtower: fix potential NULL-deref on disconnect
commit
cd81e6fa8e033e7bcd59415b4a65672b4780030b upstream.
The driver is using its struct usb_device pointer as an inverted
disconnected flag, but was setting it to NULL before making sure all
completion handlers had run. This could lead to a NULL-pointer
dereference in a number of dev_dbg and dev_err statements in the
completion handlers which relies on said pointer.
Fix this by unconditionally stopping all I/O and preventing
resubmissions by poisoning the interrupt URBs at disconnect and using a
dedicated disconnected flag.
This also makes sure that all I/O has completed by the time the
disconnect callback returns.
Fixes:
9d974b2a06e3 ("USB: legousbtower.c: remove err() usage")
Fixes:
fef526cae700 ("USB: legousbtower: remove custom debug macro")
Fixes:
4dae99638097 ("USB: legotower: remove custom debug macro and module parameter")
Cc: stable <stable@vger.kernel.org> # 3.5
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190919083039.30898-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 19 Sep 2019 08:30:37 +0000 (10:30 +0200)]
USB: legousbtower: fix deadlock on disconnect
commit
33a7813219f208f4952ece60ee255fd983272dec upstream.
Fix a potential deadlock if disconnect races with open.
Since commit
d4ead16f50f9 ("USB: prevent char device open/deregister
race") core holds an rw-semaphore while open is called and when
releasing the minor number during deregistration. This can lead to an
ABBA deadlock if a driver takes a lock in open which it also holds
during deregistration.
This effectively reverts commit
78663ecc344b ("USB: disconnect open race
in legousbtower") which needlessly introduced this issue after a generic
fix for this race had been added to core by commit
d4ead16f50f9 ("USB:
prevent char device open/deregister race").
Fixes:
78663ecc344b ("USB: disconnect open race in legousbtower")
Cc: stable <stable@vger.kernel.org> # 2.6.24
Reported-by: syzbot+f9549f5ee8a5416f0b95@syzkaller.appspotmail.com
Tested-by: syzbot+f9549f5ee8a5416f0b95@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190919083039.30898-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 19 Sep 2019 08:30:36 +0000 (10:30 +0200)]
USB: legousbtower: fix slab info leak at probe
commit
1d427be4a39defadda6dd8f4659bc17f7591740f upstream.
Make sure to check for short transfers when retrieving the version
information at probe to avoid leaking uninitialised slab data when
logging it.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190919083039.30898-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yoshihiro Shimoda [Tue, 1 Oct 2019 10:10:33 +0000 (19:10 +0900)]
usb: renesas_usbhs: gadget: Fix usb_ep_set_{halt,wedge}() behavior
commit
4d599cd3a097a85a5c68a2c82b9a48cddf9953ec upstream.
According to usb_ep_set_halt()'s description,
__usbhsg_ep_set_halt_wedge() should return -EAGAIN if the IN endpoint
has any queue or data. Otherwise, this driver is possible to cause
just STALL without sending a short packet data on g_mass_storage driver,
and then a few resetting a device happens on a host side during
a usb enumaration.
Fixes:
2f98382dcdfe ("usb: renesas_usbhs: Add Renesas USBHS Gadget")
Cc: <stable@vger.kernel.org> # v3.0+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1569924633-322-3-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yoshihiro Shimoda [Tue, 1 Oct 2019 10:10:32 +0000 (19:10 +0900)]
usb: renesas_usbhs: gadget: Do not discard queues in usb_ep_set_{halt,wedge}()
commit
1aae1394294cb71c6aa0bc904a94a7f2f1e75936 upstream.
The commit
97664a207bc2 ("usb: renesas_usbhs: shrink spin lock area")
had added a usbhsg_pipe_disable() calling into
__usbhsg_ep_set_halt_wedge() accidentally. But, this driver should
not call the usbhsg_pipe_disable() because the function discards
all queues. So, this patch removes it.
Fixes:
97664a207bc2 ("usb: renesas_usbhs: shrink spin lock area")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1569924633-322-2-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jacky.Cao@sony.com [Thu, 5 Sep 2019 04:11:57 +0000 (04:11 +0000)]
USB: dummy-hcd: fix power budget for SuperSpeed mode
commit
2636d49b64671d3d90ecc4daf971b58df3956519 upstream.
The power budget for SuperSpeed mode should be 900 mA
according to USB specification, so set the power budget
to 900mA for dummy_start_ss which is only used for
SuperSpeed mode.
If the max power consumption of SuperSpeed device is
larger than 500 mA, insufficient available bus power
error happens in usb_choose_configuration function
when the device connects to dummy hcd.
Signed-off-by: Jacky Cao <Jacky.Cao@sony.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/16EA1F625E922C43B00B9D82250220500871CDE5@APYOKXMS108.ap.sony.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 3 Oct 2019 07:09:31 +0000 (09:09 +0200)]
USB: microtek: fix info-leak at probe
commit
177238c3d47d54b2ed8f0da7a4290db492f4a057 upstream.
Add missing bulk-in endpoint sanity check to prevent uninitialised stack
data from being reported to the system log and used as endpoint
addresses.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reported-by: syzbot+5630ca7c3b2be5c9da5e@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20191003070931.17009-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 26 Sep 2019 09:12:25 +0000 (11:12 +0200)]
USB: usblcd: fix I/O after disconnect
commit
eb7f5a490c5edfe8126f64bc58b9ba2edef0a425 upstream.
Make sure to stop all I/O on disconnect by adding a disconnected flag
which is used to prevent new I/O from being started and by stopping all
ongoing I/O before returning.
This also fixes a potential use-after-free on driver unbind in case the
driver data is freed before the completion handler has run.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org> # 7bbe990c989e
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190926091228.24634-7-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Tue, 1 Oct 2019 08:49:07 +0000 (10:49 +0200)]
USB: serial: fix runtime PM after driver unbind
commit
d51bdb93ca7e71d7fb30a572c7b47ed0194bf3fe upstream.
Since commit
c2b71462d294 ("USB: core: Fix bug caused by duplicate
interface PM usage counter") USB drivers must always balance their
runtime PM gets and puts, including when the driver has already been
unbound from the interface.
Leaving the interface with a positive PM usage counter would prevent a
later bound driver from suspending the device.
Fixes:
c2b71462d294 ("USB: core: Fix bug caused by duplicate interface PM usage counter")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191001084908.2003-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reinhard Speyerer [Thu, 3 Oct 2019 16:53:21 +0000 (18:53 +0200)]
USB: serial: option: add support for Cinterion CLS8 devices
commit
dfbac2f4da6a0c4a8f6b4d715a4077a7b8df53ad upstream.
Add support for the serial ports of Cinterion CLS8 devices.
T: Bus=01 Lev=03 Prnt=05 Port=01 Cnt=02 Dev#= 25 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1e2d ProdID=00b0 Rev= 3.18
S: Manufacturer=GEMALTO
S: Product=USB Modem
C:* #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniele Palmas [Mon, 23 Sep 2019 10:23:28 +0000 (12:23 +0200)]
USB: serial: option: add Telit FN980 compositions
commit
5eb3f4b87a0e7e949c976f32f296176a06d1a93b upstream.
This patch adds the following Telit FN980 compositions:
0x1050: tty, adb, rmnet, tty, tty, tty, tty
0x1051: tty, adb, mbim, tty, tty, tty, tty
0x1052: rndis, tty, adb, tty, tty, tty, tty
0x1053: tty, adb, ecm, tty, tty, tty, tty
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Beni Mahler [Wed, 4 Sep 2019 22:26:20 +0000 (00:26 +0200)]
USB: serial: ftdi_sio: add device IDs for Sienna and Echelon PL-20
commit
357f16d9e0194cdbc36531ff88b453481560b76a upstream.
Both devices added here have a FTDI chip inside. The device from Echelon
is called 'Network Interface' it is actually a LON network gateway.
ID 0403:8348 Future Technology Devices International, Ltd
https://www.eltako.com/fileadmin/downloads/de/datenblatt/Datenblatt_PL-SW-PROF.pdf
ID 0920:7500 Network Interface
https://www.echelon.com/products/u20-usb-network-interface
Signed-off-by: Beni Mahler <beni.mahler@gmx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 3 Oct 2019 13:49:58 +0000 (15:49 +0200)]
USB: serial: keyspan: fix NULL-derefs on open() and write()
commit
7d7e21fafdbc7fcf0854b877bd0975b487ed2717 upstream.
Fix NULL-pointer dereferences on open() and write() which can be
triggered by a malicious USB device.
The current URB allocation helper would fail to initialise the newly
allocated URB if the device has unexpected endpoint descriptors,
something which could lead NULL-pointer dereferences in a number of
open() and write() paths when accessing the URB. For example:
BUG: kernel NULL pointer dereference, address:
0000000000000000
...
RIP: 0010:usb_clear_halt+0x11/0xc0
...
Call Trace:
? tty_port_open+0x4d/0xd0
keyspan_open+0x70/0x160 [keyspan]
serial_port_activate+0x5b/0x80 [usbserial]
tty_port_open+0x7b/0xd0
? check_tty_count+0x43/0xa0
tty_open+0xf1/0x490
BUG: kernel NULL pointer dereference, address:
0000000000000000
...
RIP: 0010:keyspan_write+0x14e/0x1f3 [keyspan]
...
Call Trace:
serial_write+0x43/0xa0 [usbserial]
n_tty_write+0x1af/0x4f0
? do_wait_intr_irq+0x80/0x80
? process_echoes+0x60/0x60
tty_write+0x13f/0x2f0
BUG: kernel NULL pointer dereference, address:
0000000000000000
...
RIP: 0010:keyspan_usa26_send_setup+0x298/0x305 [keyspan]
...
Call Trace:
keyspan_open+0x10f/0x160 [keyspan]
serial_port_activate+0x5b/0x80 [usbserial]
tty_port_open+0x7b/0xd0
? check_tty_count+0x43/0xa0
tty_open+0xf1/0x490
Fixes:
fdcba53e2d58 ("fix for bugzilla #7544 (keyspan USB-to-serial converter)")
Cc: stable <stable@vger.kernel.org> # 2.6.21
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Randy Dunlap [Mon, 16 Sep 2019 23:12:23 +0000 (16:12 -0700)]
serial: uartlite: fix exit path null pointer
commit
a553add0846f355a28ed4e81134012e4a1e280c2 upstream.
Call uart_unregister_driver() conditionally instead of
unconditionally, only if it has been previously registered.
This uses driver.state, just as the sh-sci.c driver does.
Fixes this null pointer dereference in tty_unregister_driver(),
since the 'driver' argument is null:
general protection fault: 0000 [#1] PREEMPT SMP KASAN PTI
RIP: 0010:tty_unregister_driver+0x25/0x1d0
Fixes:
238b8721a554 ("[PATCH] serial uartlite driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: stable <stable@vger.kernel.org>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Link: https://lore.kernel.org/r/9c8e6581-6fcc-a595-0897-4d90f5d710df@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Wed, 9 Oct 2019 15:38:46 +0000 (17:38 +0200)]
USB: ldusb: fix NULL-derefs on driver unbind
commit
58ecf131e74620305175a7aa103f81350bb37570 upstream.
The driver was using its struct usb_interface pointer as an inverted
disconnected flag, but was setting it to NULL before making sure all
completion handlers had run. This could lead to a NULL-pointer
dereference in a number of dev_dbg, dev_warn and dev_err statements in
the completion handlers which relies on said pointer.
Fix this by unconditionally stopping all I/O and preventing
resubmissions by poisoning the interrupt URBs at disconnect and using a
dedicated disconnected flag.
This also makes sure that all I/O has completed by the time the
disconnect callback returns.
Fixes:
2824bd250f0b ("[PATCH] USB: add ldusb driver")
Cc: stable <stable@vger.kernel.org> # 2.6.13
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191009153848.8664-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Wed, 9 Oct 2019 15:38:45 +0000 (17:38 +0200)]
USB: chaoskey: fix use-after-free on release
commit
93ddb1f56ae102f14f9e46a9a9c8017faa970003 upstream.
The driver was accessing its struct usb_interface in its release()
callback without holding a reference. This would lead to a
use-after-free whenever the device was disconnected while the character
device was still open.
Fixes:
66e3e591891d ("usb: Add driver for Altus Metrum ChaosKey device (v2)")
Cc: stable <stable@vger.kernel.org> # 4.1
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191009153848.8664-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Tue, 1 Oct 2019 08:49:06 +0000 (10:49 +0200)]
USB: usblp: fix runtime PM after driver unbind
commit
9a31535859bfd8d1c3ed391f5e9247cd87bb7909 upstream.
Since commit
c2b71462d294 ("USB: core: Fix bug caused by duplicate
interface PM usage counter") USB drivers must always balance their
runtime PM gets and puts, including when the driver has already been
unbound from the interface.
Leaving the interface with a positive PM usage counter would prevent a
later bound driver from suspending the device.
Fixes:
c2b71462d294 ("USB: core: Fix bug caused by duplicate interface PM usage counter")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191001084908.2003-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Wed, 9 Oct 2019 10:48:43 +0000 (12:48 +0200)]
USB: iowarrior: fix use-after-free after driver unbind
commit
b5f8d46867ca233d773408ffbe691a8062ed718f upstream.
Make sure to stop also the asynchronous write URBs on disconnect() to
avoid use-after-free in the completion handler after driver unbind.
Fixes:
946b960d13c1 ("USB: add driver for iowarrior devices.")
Cc: stable <stable@vger.kernel.org> # 2.6.21: 51a2f077c44e ("USB: introduce usb_anchor")
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191009104846.5925-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Wed, 9 Oct 2019 10:48:42 +0000 (12:48 +0200)]
USB: iowarrior: fix use-after-free on release
commit
80cd5479b525093a56ef768553045741af61b250 upstream.
The driver was accessing its struct usb_interface from its release()
callback without holding a reference. This would lead to a
use-after-free whenever debugging was enabled and the device was
disconnected while its character device was open.
Fixes:
549e83500b80 ("USB: iowarrior: Convert local dbg macro to dev_dbg")
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191009104846.5925-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Wed, 9 Oct 2019 10:48:41 +0000 (12:48 +0200)]
USB: iowarrior: fix use-after-free on disconnect
commit
edc4746f253d907d048de680a621e121517f484b upstream.
A recent fix addressing a deadlock on disconnect introduced a new bug
by moving the present flag out of the critical section protected by the
driver-data mutex. This could lead to a racing release() freeing the
driver data before disconnect() is done with it.
Due to insufficient locking a related use-after-free could be triggered
also before the above mentioned commit. Specifically, the driver needs
to hold the driver-data mutex also while checking the opened flag at
disconnect().
Fixes:
c468a8aa790e ("usb: iowarrior: fix deadlock on disconnect")
Fixes:
946b960d13c1 ("USB: add driver for iowarrior devices.")
Cc: stable <stable@vger.kernel.org> # 2.6.21
Reported-by: syzbot+0761012cebf7bdb38137@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191009104846.5925-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Wed, 9 Oct 2019 15:38:44 +0000 (17:38 +0200)]
USB: adutux: fix use-after-free on release
commit
123a0f125fa3d2104043697baa62899d9e549272 upstream.
The driver was accessing its struct usb_device in its release()
callback without holding a reference. This would lead to a
use-after-free whenever the device was disconnected while the character
device was still open.
Fixes:
66d4bc30d128 ("USB: adutux: remove custom debug macro")
Cc: stable <stable@vger.kernel.org> # 3.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191009153848.8664-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Wed, 25 Sep 2019 09:29:13 +0000 (11:29 +0200)]
USB: adutux: fix NULL-derefs on disconnect
commit
b2fa7baee744fde746c17bc1860b9c6f5c2eebb7 upstream.
The driver was using its struct usb_device pointer as an inverted
disconnected flag, but was setting it to NULL before making sure all
completion handlers had run. This could lead to a NULL-pointer
dereference in a number of dev_dbg statements in the completion handlers
which relies on said pointer.
The pointer was also dereferenced unconditionally in a dev_dbg statement
release() something which would lead to a NULL-deref whenever a device
was disconnected before the final character-device close if debugging
was enabled.
Fix this by unconditionally stopping all I/O and preventing
resubmissions by poisoning the interrupt URBs at disconnect and using a
dedicated disconnected flag.
This also makes sure that all I/O has completed by the time the
disconnect callback returns.
Fixes:
1ef37c6047fe ("USB: adutux: remove custom debug macro and module parameter")
Fixes:
66d4bc30d128 ("USB: adutux: remove custom debug macro")
Cc: stable <stable@vger.kernel.org> # 3.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190925092913.8608-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Wed, 25 Sep 2019 09:29:12 +0000 (11:29 +0200)]
USB: adutux: fix use-after-free on disconnect
commit
44efc269db7929f6275a1fa927ef082e533ecde0 upstream.
The driver was clearing its struct usb_device pointer, which it used as
an inverted disconnected flag, before deregistering the character device
and without serialising against racing release().
This could lead to a use-after-free if a racing release() callback
observes the cleared pointer and frees the driver data before
disconnect() is finished with it.
This could also lead to NULL-pointer dereferences in a racing open().
Fixes:
f08812d5eb8f ("USB: FIx locks and urb->status in adutux (updated)")
Cc: stable <stable@vger.kernel.org> # 2.6.24
Reported-by: syzbot+0243cb250a51eeefb8cc@syzkaller.appspotmail.com
Tested-by: syzbot+0243cb250a51eeefb8cc@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190925092913.8608-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Colin Ian King [Tue, 7 Nov 2017 11:45:27 +0000 (11:45 +0000)]
USB: adutux: remove redundant variable minor
commit
8444efc4a052332d643ed5c8aebcca148c7de032 upstream.
Variable minor is being assigned but never read, hence it is redundant
and can be removed. Cleans up clang warning:
drivers/usb/misc/adutux.c:770:2: warning: Value stored to 'minor' is
never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kai-Heng Feng [Fri, 4 Oct 2019 11:59:32 +0000 (14:59 +0300)]
xhci: Increase STS_SAVE timeout in xhci_suspend()
commit
ac343366846a445bb81f0a0e8f16abb8bd5d5d88 upstream.
After commit
f7fac17ca925 ("xhci: Convert xhci_handshake() to use
readl_poll_timeout_atomic()"), ASMedia xHCI may fail to suspend.
Although the algorithms are essentially the same, the old max timeout is
(usec + usec * time of doing readl()), and the new max timeout is just
usec, which is much less than the old one.
Increase the timeout to make ASMedia xHCI able to suspend again.
BugLink: https://bugs.launchpad.net/bugs/1844021
Fixes:
f7fac17ca925 ("xhci: Convert xhci_handshake() to use readl_poll_timeout_atomic()")
Cc: <stable@vger.kernel.org> # v5.2+
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-8-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rick Tseng [Fri, 4 Oct 2019 11:59:30 +0000 (14:59 +0300)]
usb: xhci: wait for CNR controller not ready bit in xhci resume
commit
a70bcbc322837eda1ab5994d12db941dc9733a7d upstream.
NVIDIA 3.1 xHCI card would lose power when moving power state into D3Cold.
Thus we need to wait for CNR bit to clear in xhci resume, just as in
xhci init.
[Minor changes to comment and commit message -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Rick Tseng <rtseng@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-6-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Schmidt [Fri, 4 Oct 2019 11:59:28 +0000 (14:59 +0300)]
xhci: Check all endpoints for LPM timeout
commit
d500c63f80f2ea08ee300e57da5f2af1c13875f5 upstream.
If an endpoint is encountered that returns USB3_LPM_DEVICE_INITIATED, keep
checking further endpoints, as there might be periodic endpoints later
that return USB3_LPM_DISABLED due to shorter service intervals.
Without this, the code can set too high a maximum-exit-latency and
prevent the use of multiple USB3 cameras that should be able to work.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jan Schmidt <jan@centricular.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-4-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Fri, 4 Oct 2019 11:59:27 +0000 (14:59 +0300)]
xhci: Prevent device initiated U1/U2 link pm if exit latency is too long
commit
cd9d9491e835a845c1a98b8471f88d26285e0bb9 upstream.
If host/hub initiated link pm is prevented by a driver flag we still must
ensure that periodic endpoints have longer service intervals than link pm
exit latency before allowing device initiated link pm.
Fix this by continue walking and checking endpoint service interval if
xhci_get_timeout_no_hub_lpm() returns anything else than USB3_LPM_DISABLED
While at it fix the split line error message
Tested-by: Jan Schmidt <jan@centricular.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-3-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Fri, 4 Oct 2019 11:59:26 +0000 (14:59 +0300)]
xhci: Fix false warning message about wrong bounce buffer write length
commit
c03101ff4f74bb30679c1a03d551ecbef1024bf6 upstream.
The check printing out the "WARN Wrong bounce buffer write length:"
uses incorrect values when comparing bytes written from scatterlist
to bounce buffer. Actual copied lengths are fine.
The used seg->bounce_len will be set to equal new_buf_len a few lines later
in the code, but is incorrect when doing the comparison.
The patch which added this false warning was backported to 4.8+ kernels
so this should be backported as far as well.
Cc: <stable@vger.kernel.org> # v4.8+
Fixes:
597c56e372da ("xhci: update bounce buffer with correct sg num")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-2-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Wed, 9 Oct 2019 17:09:42 +0000 (19:09 +0200)]
USB: usb-skeleton: fix NULL-deref on disconnect
commit
bed5ef230943863b9abf5eae226a20fad9a8ff71 upstream.
The driver was using its struct usb_interface pointer as an inverted
disconnected flag and was setting it to NULL before making sure all
completion handlers had run. This could lead to NULL-pointer
dereferences in the dev_err() statements in the completion handlers
which relies on said pointer.
Fix this by using a dedicated disconnected flag.
Note that this is also addresses a NULL-pointer dereference at release()
and a struct usb_interface reference leak introduced by a recent runtime
PM fix, which depends on and should have been submitted together with
this patch.
Fixes:
4212cd74ca6f ("USB: usb-skeleton.c: remove err() usage")
Fixes:
5c290a5e42c3 ("USB: usb-skeleton: fix runtime PM after driver unbind")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191009170944.30057-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Tue, 1 Oct 2019 08:49:05 +0000 (10:49 +0200)]
USB: usb-skeleton: fix runtime PM after driver unbind
commit
5c290a5e42c3387e82de86965784d30e6c5270fd upstream.
Since commit
c2b71462d294 ("USB: core: Fix bug caused by duplicate
interface PM usage counter") USB drivers must always balance their
runtime PM gets and puts, including when the driver has already been
unbound from the interface.
Leaving the interface with a positive PM usage counter would prevent a
later bound driver from suspending the device.
Fixes:
c2b71462d294 ("USB: core: Fix bug caused by duplicate interface PM usage counter")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191001084908.2003-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Wed, 9 Oct 2019 15:38:48 +0000 (17:38 +0200)]
USB: yurex: fix NULL-derefs on disconnect
commit
aafb00a977cf7d81821f7c9d12e04c558c22dc3c upstream.
The driver was using its struct usb_interface pointer as an inverted
disconnected flag, but was setting it to NULL without making sure all
code paths that used it were done with it.
Before commit
ef61eb43ada6 ("USB: yurex: Fix protection fault after
device removal") this included the interrupt-in completion handler, but
there are further accesses in dev_err and dev_dbg statements in
yurex_write() and the driver-data destructor (sic!).
Fix this by unconditionally stopping also the control URB at disconnect
and by using a dedicated disconnected flag.
Note that we need to take a reference to the struct usb_interface to
avoid a use-after-free in the destructor whenever the device was
disconnected while the character device was still open.
Fixes:
aadd6472d904 ("USB: yurex.c: remove dbg() usage")
Fixes:
45714104b9e8 ("USB: yurex.c: remove err() usage")
Cc: stable <stable@vger.kernel.org> # 3.5: ef61eb43ada6
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191009153848.8664-6-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Tue, 17 Sep 2019 16:47:23 +0000 (12:47 -0400)]
USB: yurex: Don't retry on unexpected errors
commit
32a0721c6620b77504916dac0cea8ad497c4878a upstream.
According to Greg KH, it has been generally agreed that when a USB
driver encounters an unknown error (or one it can't handle directly),
it should just give up instead of going into a potentially infinite
retry loop.
The three codes -EPROTO, -EILSEQ, and -ETIME fall into this category.
They can be caused by bus errors such as packet loss or corruption,
attempting to communicate with a disconnected device, or by malicious
firmware. Nowadays the extent of packet loss or corruption is
negligible, so it should be safe for a driver to give up whenever one
of these errors occurs.
Although the yurex driver handles -EILSEQ errors in this way, it
doesn't do the same for -EPROTO (as discovered by the syzbot fuzzer)
or other unrecognized errors. This patch adjusts the driver so that
it doesn't log an error message for -EPROTO or -ETIME, and it doesn't
retry after any errors.
Reported-and-tested-by: syzbot+b24d736f18a1541ad550@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1909171245410.1590-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bastien Nocera [Mon, 23 Sep 2019 16:18:43 +0000 (18:18 +0200)]
USB: rio500: Remove Rio 500 kernel driver
commit
015664d15270a112c2371d812f03f7c579b35a73 upstream.
The Rio500 kernel driver has not been used by Rio500 owners since 2001
not long after the rio500 project added support for a user-space USB stack
through the very first versions of usbdevfs and then libusb.
Support for the kernel driver was removed from the upstream utilities
in 2008:
https://gitlab.freedesktop.org/hadess/rio500/commit/
943f624ab721eb8281c287650fcc9e2026f6f5db
Cc: Cesar Miquel <miquel@df.uba.ar>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/6251c17584d220472ce882a3d9c199c401a51a71.camel@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Icenowy Zheng [Thu, 25 Jul 2019 03:08:52 +0000 (11:08 +0800)]
f2fs: use EINVAL for superblock with invalid magic
[ Upstream commit
38fb6d0ea34299d97b031ed64fe994158b6f8eb3 ]
The kernel mount_block_root() function expects -EACESS or -EINVAL for a
unmountable filesystem when trying to mount the root with different
filesystem types.
However, in 5.3-rc1 the behavior when F2FS code cannot find valid block
changed to return -EFSCORRUPTED(-EUCLEAN), and this error code makes
mount_block_root() fail when trying to probe F2FS.
When the magic number of the superblock mismatches, it has a high
probability that it's just not a F2FS. In this case return -EINVAL seems
to be a better result, and this return value can make mount_block_root()
probing work again.
Return -EINVAL when the superblock has magic mismatch, -EFSCORRUPTED in
other cases (the magic matches but the superblock cannot be recognized).
Fixes:
10f966bbf521 ("f2fs: use generic EFSBADCRC/EFSCORRUPTED")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Will Deacon [Mon, 7 Oct 2019 00:58:00 +0000 (17:58 -0700)]
panic: ensure preemption is disabled during panic()
commit
20bb759a66be52cf4a9ddd17fddaf509e11490cd upstream.
Calling 'panic()' on a kernel with CONFIG_PREEMPT=y can leave the
calling CPU in an infinite loop, but with interrupts and preemption
enabled. From this state, userspace can continue to be scheduled,
despite the system being "dead" as far as the kernel is concerned.
This is easily reproducible on arm64 when booting with "nosmp" on the
command line; a couple of shell scripts print out a periodic "Ping"
message whilst another triggers a crash by writing to
/proc/sysrq-trigger:
| sysrq: Trigger a crash
| Kernel panic - not syncing: sysrq triggered crash
| CPU: 0 PID: 1 Comm: init Not tainted 5.2.15 #1
| Hardware name: linux,dummy-virt (DT)
| Call trace:
| dump_backtrace+0x0/0x148
| show_stack+0x14/0x20
| dump_stack+0xa0/0xc4
| panic+0x140/0x32c
| sysrq_handle_reboot+0x0/0x20
| __handle_sysrq+0x124/0x190
| write_sysrq_trigger+0x64/0x88
| proc_reg_write+0x60/0xa8
| __vfs_write+0x18/0x40
| vfs_write+0xa4/0x1b8
| ksys_write+0x64/0xf0
| __arm64_sys_write+0x14/0x20
| el0_svc_common.constprop.0+0xb0/0x168
| el0_svc_handler+0x28/0x78
| el0_svc+0x8/0xc
| Kernel Offset: disabled
| CPU features: 0x0002,
24002004
| Memory Limit: none
| ---[ end Kernel panic - not syncing: sysrq triggered crash ]---
| Ping 2!
| Ping 1!
| Ping 1!
| Ping 2!
The issue can also be triggered on x86 kernels if CONFIG_SMP=n,
otherwise local interrupts are disabled in 'smp_send_stop()'.
Disable preemption in 'panic()' before re-enabling interrupts.
Link: http://lkml.kernel.org/r/20191002123538.22609-1-will@kernel.org
Link: https://lore.kernel.org/r/BX1W47JXPMR8.58IYW53H6M5N@dragonstone
Signed-off-by: Will Deacon <will@kernel.org>
Reported-by: Xogium <contact@xogium.me>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Fri, 11 Oct 2019 16:18:50 +0000 (18:18 +0200)]
Linux 4.14.149
Oleksandr Suvorov [Wed, 9 Oct 2019 14:38:41 +0000 (14:38 +0000)]
ASoC: sgtl5000: Improve VAG power and mute control
[ Upstream commit
b1f373a11d25fc9a5f7679c9b85799fe09b0dc4a ]
VAG power control is improved to fit the manual [1]. This patch fixes as
minimum one bug: if customer muxes Headphone to Line-In right after boot,
the VAG power remains off that leads to poor sound quality from line-in.
I.e. after boot:
- Connect sound source to Line-In jack;
- Connect headphone to HP jack;
- Run following commands:
$ amixer set 'Headphone' 80%
$ amixer set 'Headphone Mux' LINE_IN
Change VAG power on/off control according to the following algorithm:
- turn VAG power ON on the 1st incoming event.
- keep it ON if there is any active VAG consumer (ADC/DAC/HP/Line-In).
- turn VAG power OFF when there is the latest consumer's pre-down event
come.
- always delay after VAG power OFF to avoid pop.
- delay after VAG power ON if the initiative consumer is Line-In, this
prevents pop during line-in muxing.
According to the data sheet [1], to avoid any pops/clicks,
the outputs should be muted during input/output
routing changes.
[1] https://www.nxp.com/docs/en/data-sheet/SGTL5000.pdf
Cc: stable@vger.kernel.org
Fixes:
9b34e6cc3bc2 ("ASoC: Add Freescale SGTL5000 codec support")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20190719100524.23300-3-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Johannes Berg [Fri, 20 Sep 2019 19:54:17 +0000 (21:54 +0200)]
nl80211: validate beacon head
commit
f88eb7c0d002a67ef31aeb7850b42ff69abc46dc upstream.
We currently don't validate the beacon head, i.e. the header,
fixed part and elements that are to go in front of the TIM
element. This means that the variable elements there can be
malformed, e.g. have a length exceeding the buffer size, but
most downstream code from this assumes that this has already
been checked.
Add the necessary checks to the netlink policy.
Cc: stable@vger.kernel.org
Fixes:
ed1b6cc7f80f ("cfg80211/nl80211: add beacon settings")
Link: https://lore.kernel.org/r/1569009255-I7ac7fbe9436e9d8733439eab8acbbd35e55c74ef@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jouni Malinen [Mon, 11 Feb 2019 14:29:04 +0000 (16:29 +0200)]
cfg80211: Use const more consistently in for_each_element macros
commit
7388afe09143210f555bdd6c75035e9acc1fab96 upstream.
Enforce the first argument to be a correct type of a pointer to struct
element and avoid unnecessary typecasts from const to non-const pointers
(the change in validate_ie_attr() is needed to make this part work). In
addition, avoid signed/unsigned comparison within for_each_element() and
mark struct element packed just in case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johannes Berg [Thu, 7 Feb 2019 20:44:41 +0000 (21:44 +0100)]
cfg80211: add and use strongly typed element iteration macros
commit
0f3b07f027f87a38ebe5c436490095df762819be upstream.
Rather than always iterating elements from frames with pure
u8 pointers, add a type "struct element" that encapsulates
the id/datalen/data format of them.
Then, add the element iteration macros
* for_each_element
* for_each_element_id
* for_each_element_extid
which take, as their first 'argument', such a structure and
iterate through a given u8 array interpreting it as elements.
While at it and since we'll need it, also add
* for_each_subelement
* for_each_subelement_id
* for_each_subelement_extid
which instead of taking data/length just take an outer element
and use its data/datalen.
Also add for_each_element_completed() to determine if any of
the loops above completed, i.e. it was able to parse all of
the elements successfully and no data remained.
Use for_each_element_id() in cfg80211_find_ie_match() as the
first user of this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrew Murray [Thu, 29 Aug 2019 20:28:35 +0000 (14:28 -0600)]
coresight: etm4x: Use explicit barriers on enable/disable
commit
1004ce4c255fc3eb3ad9145ddd53547d1b7ce327 upstream.
Synchronization is recommended before disabling the trace registers
to prevent any start or stop points being speculative at the point
of disabling the unit (section 7.3.77 of ARM IHI 0064D).
Synchronization is also recommended after programming the trace
registers to ensure all updates are committed prior to normal code
resuming (section 4.3.7 of ARM IHI 0064D).
Let's ensure these syncronization points are present in the code
and clearly commented.
Note that we could rely on the barriers in CS_LOCK and
coresight_disclaim_device_unlocked or the context switch to user
space - however coresight may be of use in the kernel.
On armv8 the mb macro is defined as dsb(sy) - Given that the etm4x is
only used on armv8 let's directly use dsb(sy) instead of mb(). This
removes some ambiguity and makes it easier to correlate the code with
the TRM.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[Fixed capital letter for "use" in title]
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20190829202842.580-11-mathieu.poirier@linaro.org
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Sandeen [Wed, 2 Oct 2019 21:17:54 +0000 (16:17 -0500)]
vfs: Fix EOVERFLOW testing in put_compat_statfs64
commit
cc3a7bfe62b947b423fcb2cfe89fcba92bf48fa3 upstream.
Today, put_compat_statfs64() disallows nearly any field value over
2^32 if f_bsize is only 32 bits, but that makes no sense.
compat_statfs64 is there for the explicit purpose of providing 64-bit
fields for f_files, f_ffree, etc. And f_bsize is always only 32 bits.
As a result, 32-bit userspace gets -EOVERFLOW for i.e. large file
counts even with -D_FILE_OFFSET_BITS=64 set.
In reality, only f_bsize and f_frsize can legitimately overflow
(fields like f_type and f_namelen should never be large), so test
only those fields.
This bug was discussed at length some time ago, and this is the proposal
Al suggested at https://lkml.org/lkml/2018/8/6/640. It seemed to get
dropped amid the discussion of other related changes, but this
part seems obviously correct on its own, so I've picked it up and
sent it, for expediency.
Fixes:
64d2ab32efe3 ("vfs: fix put_compat_statfs64() does not handle errors")
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Srikar Dronamraju [Wed, 4 Sep 2019 09:47:37 +0000 (15:17 +0530)]
perf stat: Reset previous counts on repeat with interval
[ Upstream commit
b63fd11cced17fcb8e133def29001b0f6aaa5e06 ]
When using 'perf stat' with repeat and interval option, it shows wrong
values for events.
The wrong values will be shown for the first interval on the second and
subsequent repetitions.
Without the fix:
# perf stat -r 3 -I 2000 -e faults -e sched:sched_switch -a sleep 5
2.
000282489 53 faults
2.
000282489 513 sched:sched_switch
4.
005478208 3,721 faults
4.
005478208 2,666 sched:sched_switch
5.
025470933 395 faults
5.
025470933 1,307 sched:sched_switch
2.
009602825 1,84,46,74,40,73,70,95,47,520 faults <------
2.
009602825 1,84,46,74,40,73,70,95,49,568 sched:sched_switch <------
4.
019612206 4,730 faults
4.
019612206 2,746 sched:sched_switch
5.
039615484 3,953 faults
5.
039615484 1,496 sched:sched_switch
2.
000274620 1,84,46,74,40,73,70,95,47,520 faults <------
2.
000274620 1,84,46,74,40,73,70,95,47,520 sched:sched_switch <------
4.
000480342 4,282 faults
4.
000480342 2,303 sched:sched_switch
5.
000916811 1,322 faults
5.
000916811 1,064 sched:sched_switch
#
prev_raw_counts is allocated when using intervals. This is used when
calculating the difference in the counts of events when using interval.
The current counts are stored in prev_raw_counts to calculate the
differences in the next iteration.
On the first interval of the second and subsequent repetitions,
prev_raw_counts would be the values stored in the last interval of the
previous repetitions, while the current counts will only be for the
first interval of the current repetition.
Hence there is a possibility of events showing up as big number.
Fix this by resetting prev_raw_counts whenever perf stat repeats the
command.
With the fix:
# perf stat -r 3 -I 2000 -e faults -e sched:sched_switch -a sleep 5
2.
019349347 2,597 faults
2.
019349347 2,753 sched:sched_switch
4.
019577372 3,098 faults
4.
019577372 2,532 sched:sched_switch
5.
019415481 1,879 faults
5.
019415481 1,356 sched:sched_switch
2.
000178813 8,468 faults
2.
000178813 2,254 sched:sched_switch
4.
000404621 7,440 faults
4.
000404621 1,266 sched:sched_switch
5.
040196079 2,458 faults
5.
040196079 556 sched:sched_switch
2.
000191939 6,870 faults
2.
000191939 1,170 sched:sched_switch
4.
000414103 541 faults
4.
000414103 902 sched:sched_switch
5.
000809863 450 faults
5.
000809863 364 sched:sched_switch
#
Committer notes:
This was broken since the cset introducing the --interval feature, i.e.
--repeat + --interval wasn't tested at that point, add the Fixes tag so
that automatic scripts can pick this up.
Fixes:
13370a9b5bb8 ("perf stat: Add interval printing")
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Tested-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: stable@vger.kernel.org # v3.9+
Link: http://lore.kernel.org/lkml/20190904094738.9558-2-srikar@linux.vnet.ibm.com
[ Fixed up conflicts with libperf, i.e. some perf_{evsel,evlist} lost the 'perf' prefix ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Srikar Dronamraju [Wed, 4 Sep 2019 09:47:38 +0000 (15:17 +0530)]
perf stat: Fix a segmentation fault when using repeat forever
[ Upstream commit
443f2d5ba13d65ccfd879460f77941875159d154 ]
Observe a segmentation fault when 'perf stat' is asked to repeat forever
with the interval option.
Without fix:
# perf stat -r 0 -I 5000 -e cycles -a sleep 10
# time counts unit events
5.
000211692 3,13,89,82,34,157 cycles
10.
000380119 1,53,98,52,22,294 cycles
10.
040467280 17,16,79,265 cycles
Segmentation fault
This problem was only observed when we use forever option aka -r 0 and
works with limited repeats. Calling print_counter with ts being set to
NULL, is not a correct option when interval is set. Hence avoid
print_counter(NULL,..) if interval is set.
With fix:
# perf stat -r 0 -I 5000 -e cycles -a sleep 10
# time counts unit events
5.
019866622 3,15,14,43,08,697 cycles
10.
039865756 3,15,16,31,95,261 cycles
10.
059950628 1,26,05,47,158 cycles
5.
009902655 3,14,52,62,33,932 cycles
10.
019880228 3,14,52,22,89,154 cycles
10.
030543876 66,90,18,333 cycles
5.
009848281 3,14,51,98,25,437 cycles
10.
029854402 3,15,14,93,04,918 cycles
5.
009834177 3,14,51,95,92,316 cycles
Committer notes:
Did the 'git bisect' to find the cset introducing the problem to add the
Fixes tag below, and at that time the problem reproduced as:
(gdb) run stat -r0 -I500 sleep 1
<SNIP>
Program received signal SIGSEGV, Segmentation fault.
print_interval (prefix=prefix@entry=0x7fffffffc8d0 "", ts=ts@entry=0x0) at builtin-stat.c:866
866 sprintf(prefix, "%6lu.%09lu%s", ts->tv_sec, ts->tv_nsec, csv_sep);
(gdb) bt
#0 print_interval (prefix=prefix@entry=0x7fffffffc8d0 "", ts=ts@entry=0x0) at builtin-stat.c:866
#1 0x000000000041860a in print_counters (ts=ts@entry=0x0, argc=argc@entry=2, argv=argv@entry=0x7fffffffd640) at builtin-stat.c:938
#2 0x0000000000419a7f in cmd_stat (argc=2, argv=0x7fffffffd640, prefix=<optimized out>) at builtin-stat.c:1411
#3 0x000000000045c65a in run_builtin (p=p@entry=0x6291b8 <commands+216>, argc=argc@entry=5, argv=argv@entry=0x7fffffffd640) at perf.c:370
#4 0x000000000045c893 in handle_internal_command (argc=5, argv=0x7fffffffd640) at perf.c:429
#5 0x000000000045c8f1 in run_argv (argcp=argcp@entry=0x7fffffffd4ac, argv=argv@entry=0x7fffffffd4a0) at perf.c:473
#6 0x000000000045cac9 in main (argc=<optimized out>, argv=<optimized out>) at perf.c:588
(gdb)
Mostly the same as just before this patch:
Program received signal SIGSEGV, Segmentation fault.
0x00000000005874a7 in print_interval (config=0xa1f2a0 <stat_config>, evlist=0xbc9b90, prefix=0x7fffffffd1c0 "`", ts=0x0) at util/stat-display.c:964
964 sprintf(prefix, "%6lu.%09lu%s", ts->tv_sec, ts->tv_nsec, config->csv_sep);
(gdb) bt
#0 0x00000000005874a7 in print_interval (config=0xa1f2a0 <stat_config>, evlist=0xbc9b90, prefix=0x7fffffffd1c0 "`", ts=0x0) at util/stat-display.c:964
#1 0x0000000000588047 in perf_evlist__print_counters (evlist=0xbc9b90, config=0xa1f2a0 <stat_config>, _target=0xa1f0c0 <target>, ts=0x0, argc=2, argv=0x7fffffffd670)
at util/stat-display.c:1172
#2 0x000000000045390f in print_counters (ts=0x0, argc=2, argv=0x7fffffffd670) at builtin-stat.c:656
#3 0x0000000000456bb5 in cmd_stat (argc=2, argv=0x7fffffffd670) at builtin-stat.c:1960
#4 0x00000000004dd2e0 in run_builtin (p=0xa30e00 <commands+288>, argc=5, argv=0x7fffffffd670) at perf.c:310
#5 0x00000000004dd54d in handle_internal_command (argc=5, argv=0x7fffffffd670) at perf.c:362
#6 0x00000000004dd694 in run_argv (argcp=0x7fffffffd4cc, argv=0x7fffffffd4c0) at perf.c:406
#7 0x00000000004dda11 in main (argc=5, argv=0x7fffffffd670) at perf.c:531
(gdb)
Fixes:
d4f63a4741a8 ("perf stat: Introduce print_counters function")
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Tested-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # v4.2+
Link: http://lore.kernel.org/lkml/20190904094738.9558-3-srikar@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jiri Olsa [Thu, 12 Sep 2019 10:52:35 +0000 (12:52 +0200)]
perf tools: Fix segfault in cpu_cache_level__read()
[ Upstream commit
0216234c2eed1367a318daeb9f4a97d8217412a0 ]
We release wrong pointer on error path in cpu_cache_level__read
function, leading to segfault:
(gdb) r record ls
Starting program: /root/perf/tools/perf/perf record ls
...
[ perf record: Woken up 1 times to write data ]
double free or corruption (out)
Thread 1 "perf" received signal SIGABRT, Aborted.
0x00007ffff7463798 in raise () from /lib64/power9/libc.so.6
(gdb) bt
#0 0x00007ffff7463798 in raise () from /lib64/power9/libc.so.6
#1 0x00007ffff7443bac in abort () from /lib64/power9/libc.so.6
#2 0x00007ffff74af8bc in __libc_message () from /lib64/power9/libc.so.6
#3 0x00007ffff74b92b8 in malloc_printerr () from /lib64/power9/libc.so.6
#4 0x00007ffff74bb874 in _int_free () from /lib64/power9/libc.so.6
#5 0x0000000010271260 in __zfree (ptr=0x7fffffffa0b0) at ../../lib/zalloc..
#6 0x0000000010139340 in cpu_cache_level__read (cache=0x7fffffffa090, cac..
#7 0x0000000010143c90 in build_caches (cntp=0x7fffffffa118, size=<optimiz..
...
Releasing the proper pointer.
Fixes:
720e98b5faf1 ("perf tools: Add perf data cache feature")
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org: # v4.6+
Link: http://lore.kernel.org/lkml/20190912105235.10689-1-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Balasubramani Vivekanandan [Thu, 26 Sep 2019 13:51:01 +0000 (15:51 +0200)]
tick: broadcast-hrtimer: Fix a race in bc_set_next
[ Upstream commit
b9023b91dd020ad7e093baa5122b6968c48cc9e0 ]
When a cpu requests broadcasting, before starting the tick broadcast
hrtimer, bc_set_next() checks if the timer callback (bc_handler) is active
using hrtimer_try_to_cancel(). But hrtimer_try_to_cancel() does not provide
the required synchronization when the callback is active on other core.
The callback could have already executed tick_handle_oneshot_broadcast()
and could have also returned. But still there is a small time window where
the hrtimer_try_to_cancel() returns -1. In that case bc_set_next() returns
without doing anything, but the next_event of the tick broadcast clock
device is already set to a timeout value.
In the race condition diagram below, CPU #1 is running the timer callback
and CPU #2 is entering idle state and so calls bc_set_next().
In the worst case, the next_event will contain an expiry time, but the
hrtimer will not be started which happens when the racing callback returns
HRTIMER_NORESTART. The hrtimer might never recover if all further requests
from the CPUs to subscribe to tick broadcast have timeout greater than the
next_event of tick broadcast clock device. This leads to cascading of
failures and finally noticed as rcu stall warnings
Here is a depiction of the race condition
CPU #1 (Running timer callback) CPU #2 (Enter idle
and subscribe to
tick broadcast)
--------------------- ---------------------
__run_hrtimer() tick_broadcast_enter()
bc_handler() __tick_broadcast_oneshot_control()
tick_handle_oneshot_broadcast()
raw_spin_lock(&tick_broadcast_lock);
dev->next_event = KTIME_MAX; //wait for tick_broadcast_lock
//next_event for tick broadcast clock
set to KTIME_MAX since no other cores
subscribed to tick broadcasting
raw_spin_unlock(&tick_broadcast_lock);
if (dev->next_event == KTIME_MAX)
return HRTIMER_NORESTART
// callback function exits without
restarting the hrtimer //tick_broadcast_lock acquired
raw_spin_lock(&tick_broadcast_lock);
tick_broadcast_set_event()
clockevents_program_event()
dev->next_event = expires;
bc_set_next()
hrtimer_try_to_cancel()
//returns -1 since the timer
callback is active. Exits without
restarting the timer
cpu_base->running = NULL;
The comment that hrtimer cannot be armed from within the callback is
wrong. It is fine to start the hrtimer from within the callback. Also it is
safe to start the hrtimer from the enter/exit idle code while the broadcast
handler is active. The enter/exit idle code and the broadcast handler are
synchronized using tick_broadcast_lock. So there is no need for the
existing try to cancel logic. All this can be removed which will eliminate
the race condition as well.
Fixes:
5d1638acb9f6 ("tick: Introduce hrtimer based broadcast")
Originally-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Balasubramani Vivekanandan <balasubramani_vivekanandan@mentor.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190926135101.12102-2-balasubramani_vivekanandan@mentor.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Steven Rostedt (VMware) [Wed, 28 Aug 2019 19:05:28 +0000 (15:05 -0400)]
tools lib traceevent: Do not free tep->cmdlines in add_new_comm() on failure
[ Upstream commit
e0d2615856b2046c2e8d5bfd6933f37f69703b0b ]
If the re-allocation of tep->cmdlines succeeds, then the previous
allocation of tep->cmdlines will be freed. If we later fail in
add_new_comm(), we must not free cmdlines, and also should assign
tep->cmdlines to the new allocation. Otherwise when freeing tep, the
tep->cmdlines will be pointing to garbage.
Fixes:
a6d2a61ac653a ("tools lib traceevent: Remove some die() calls")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: linux-trace-devel@vger.kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20190828191819.970121417@goodmis.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Gautham R. Shenoy [Wed, 15 May 2019 07:45:52 +0000 (13:15 +0530)]
powerpc/pseries: Fix cpu_hotplug_lock acquisition in resize_hpt()
[ Upstream commit
c784be435d5dae28d3b03db31753dd7a18733f0c ]
The calls to arch_add_memory()/arch_remove_memory() are always made
with the read-side cpu_hotplug_lock acquired via memory_hotplug_begin().
On pSeries, arch_add_memory()/arch_remove_memory() eventually call
resize_hpt() which in turn calls stop_machine() which acquires the
read-side cpu_hotplug_lock again, thereby resulting in the recursive
acquisition of this lock.
In the absence of CONFIG_PROVE_LOCKING, we hadn't observed a system
lockup during a memory hotplug operation because cpus_read_lock() is a
per-cpu rwsem read, which, in the fast-path (in the absence of the
writer, which in our case is a CPU-hotplug operation) simply
increments the read_count on the semaphore. Thus a recursive read in
the fast-path doesn't cause any problems.
However, we can hit this problem in practice if there is a concurrent
CPU-Hotplug operation in progress which is waiting to acquire the
write-side of the lock. This will cause the second recursive read to
block until the writer finishes. While the writer is blocked since the
first read holds the lock. Thus both the reader as well as the writers
fail to make any progress thereby blocking both CPU-Hotplug as well as
Memory Hotplug operations.
Memory-Hotplug CPU-Hotplug
CPU 0 CPU 1
------ ------
1. down_read(cpu_hotplug_lock.rw_sem)
[memory_hotplug_begin]
2. down_write(cpu_hotplug_lock.rw_sem)
[cpu_up/cpu_down]
3. down_read(cpu_hotplug_lock.rw_sem)
[stop_machine()]
Lockdep complains as follows in these code-paths.
swapper/0/1 is trying to acquire lock:
(____ptrval____) (cpu_hotplug_lock.rw_sem){++++}, at: stop_machine+0x2c/0x60
but task is already holding lock:
(____ptrval____) (cpu_hotplug_lock.rw_sem){++++}, at: mem_hotplug_begin+0x20/0x50
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(cpu_hotplug_lock.rw_sem);
lock(cpu_hotplug_lock.rw_sem);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by swapper/0/1:
#0: (____ptrval____) (&dev->mutex){....}, at: __driver_attach+0x12c/0x1b0
#1: (____ptrval____) (cpu_hotplug_lock.rw_sem){++++}, at: mem_hotplug_begin+0x20/0x50
#2: (____ptrval____) (mem_hotplug_lock.rw_sem){++++}, at: percpu_down_write+0x54/0x1a0
stack backtrace:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted
5.0.0-rc5-58373-gbc99402235f3-dirty #166
Call Trace:
dump_stack+0xe8/0x164 (unreliable)
__lock_acquire+0x1110/0x1c70
lock_acquire+0x240/0x290
cpus_read_lock+0x64/0xf0
stop_machine+0x2c/0x60
pseries_lpar_resize_hpt+0x19c/0x2c0
resize_hpt_for_hotplug+0x70/0xd0
arch_add_memory+0x58/0xfc
devm_memremap_pages+0x5e8/0x8f0
pmem_attach_disk+0x764/0x830
nvdimm_bus_probe+0x118/0x240
really_probe+0x230/0x4b0
driver_probe_device+0x16c/0x1e0
__driver_attach+0x148/0x1b0
bus_for_each_dev+0x90/0x130
driver_attach+0x34/0x50
bus_add_driver+0x1a8/0x360
driver_register+0x108/0x170
__nd_driver_register+0xd0/0xf0
nd_pmem_driver_init+0x34/0x48
do_one_initcall+0x1e0/0x45c
kernel_init_freeable+0x540/0x64c
kernel_init+0x2c/0x160
ret_from_kernel_thread+0x5c/0x68
Fix this issue by
1) Requiring all the calls to pseries_lpar_resize_hpt() be made
with cpu_hotplug_lock held.
2) In pseries_lpar_resize_hpt() invoke stop_machine_cpuslocked()
as a consequence of 1)
3) To satisfy 1), in hpt_order_set(), call mmu_hash_ops.resize_hpt()
with cpu_hotplug_lock held.
Fixes:
dbcf929c0062 ("powerpc/pseries: Add support for hash table resizing")
Cc: stable@vger.kernel.org # v4.11+
Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1557906352-29048-1-git-send-email-ego@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mike Christie [Sun, 4 Aug 2019 19:10:06 +0000 (14:10 -0500)]
nbd: fix max number of supported devs
[ Upstream commit
e9e006f5fcf2bab59149cb38a48a4817c1b538b4 ]
This fixes a bug added in 4.10 with commit:
commit
9561a7ade0c205bc2ee035a2ac880478dcc1a024
Author: Josef Bacik <jbacik@fb.com>
Date: Tue Nov 22 14:04:40 2016 -0500
nbd: add multi-connection support
that limited the number of devices to 256. Before the patch we could
create 1000s of devices, but the patch switched us from using our
own thread to using a work queue which has a default limit of 256
active works.
The problem is that our recv_work function sits in a loop until
disconnection but only handles IO for one connection. The work is
started when the connection is started/restarted, but if we end up
creating 257 or more connections, the queue_work call just queues
connection257+'s recv_work and that waits for connection 1 - 256's
recv_work to be disconnected and that work instance completing.
Instead of reverting back to kthreads, this has us allocate a
workqueue_struct per device, so we can block in the work.
Cc: stable@vger.kernel.org
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dan Melnic [Mon, 18 Sep 2017 20:08:51 +0000 (13:08 -0700)]
block/ndb: add WQ_UNBOUND to the knbd-recv workqueue
[ Upstream commit
2189c97cdbed630d5971ab22f05dc998774e354e ]
Add WQ_UNBOUND to the knbd-recv workqueue so we're not bound
to a single CPU that is selected at device creation time.
Signed-off-by: Dan Melnic <dmm@fb.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / GitHub / LineageOS / android_kernel_motorola_exynos9610.git / log