brcmfmac: make brcmf_p2p_detach() call conditional

During verification of error handling in brcmf_cfg80211_attach() a
null pointer dereference occurred upon calling brcmf_p2p_detach()
from brcmf_detach(). This should only be called when the
brcmf_cfg80211_attach() has succeeded.

Fixes: f7a40873d2fa ("brcmfmac: assure p2pdev is unregistered upon driver unload")
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: fix double free of p2pdev interface

When freeing the driver ifp pointer it should also be removed from
the driver interface list, which is what brcmf_remove_interface()
does. Otherwise, the ifp pointer will be freed twice triggering
a kernel oops.

Fixes: f37d69a4babc ("brcmfmac: free ifp for non-netdev interface in p2p module")
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: add missing break statement in switch case

This patch adds missing break statement at the end of
EVENT_BT_COEX_WLAN_PARA_CHANGE switch section.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Merge ath-next from ath.git

Major changes:

wil6210:

* add modparam for bcast ring size
* support hidden SSID
* add per-MCS Rx stats

rt2800: fix assigning same WCID for different stations

On some hardware reading WCID entries table results getting 0xff
numbers, no matter of value written there before. This cause assigning
the same WCID for different stations and makes not possible to connect
to more than one station.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: assure p2pdev is unregistered upon driver unload

When unloading the driver with a p2pdev interface it resulted in
a warning upon calling wiphy_unregister() and subsequently a crash
in the driver. This patch assures the p2pdev is unregistered calling
unregister_wdev() before doing the wiphy_unregister().

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: move p2p attach/detach functions

Moving two functions in p2p.c as is so next change will be
easier to review.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: free ifp for non-netdev interface in p2p module

Making it more clear by freeing the ifp in same place where the
vif object is freed.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: have sdio return -EIO when device communication is not possible

The bus interface functions txctl and rxctl may be used while the device
can not be accessed, eg. upon driver .remove() callback. This patch will
immediately return -EIO when this is the case which speeds up the module
unload.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: rework .get_station() callback

The .get_station() cfg80211 callback is used in several scenarios. In
managed mode it can obtain information about the access-point and its
BSS parameters. In managed mode it can also obtain information about
TDLS peers. In AP mode it can obtain information about connected
clients.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Build wiphy mode and interface combinations dynamically

Switch from using semi hard coded interface combinations. This makes
it easier to announce what the firmware actually supports. This fixes
the case where brcmfmac announces p2p but the firmware doesn't
support it.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Pontus Fuchs <pontusf@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Check if firmware supports p2p

Add a feature flag to reflect the firmware's p2p capability.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Pontus Fuchs <pontusf@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mt7601u: don't warn about devices without per-rate power table

We expect EEPROM per-rate power table to be filled with
s6 values and warn user if values are invalid.  However,
there appear to be devices which don't have this section
of EEPROM initialized.  In such case we should ignore
the values and leave the driver power tables set to zero.

Note that vendor driver doesn't care about this case but
mt76x2 skips 0xff per value.  We take mt76x2's approach.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

MAINTAINERS: remove rt2x00.serialmonkey.com list and web page

rt2x00.serialmonkey.com will be shutdown.

Since traffic on rt2x00 mailing list is very low, we can use only
linux-wireless list for any rt2x00 related topics.

Thanks for Luis Correia, Ivo van Doorn and Mark Wallis for maintaining
rt2x00 servers for years!

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: handle BT coex event to adjust Rx BA window size

If timeshare coexistance between bluetooth and WLAN gets enabled,
firmware will give host an event to reduce Rx AMPDU BA window size.
The event is handled in this patch.

Signed-off-by: Chunfan Chen <jeffc@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath9k_htc: add support of channel switch

Add the support of channel switching functionality, similar
to ath9k support.

Tested with TP-Link TL-WN722N and TL-WN821N.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: use debugfs_create_devm_seqfile() helper function

Some time ago the function debugfs_create_devm_seqfile() was
introduced in debugfs. The caller simply needs to provide a
device pointer and read function. The function brcmf_debugfs_add_entry()
is now simply a wrapper only doing the work for CONFIG_BRCMDBG.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: remove watchdog reset from brcmf_pcie_buscoreprep()

The watchdog reset as done in brcmf_pcie_buscoreprep() is not
sufficient. It needs to modify PCIe core registers as well
which is properly done by brcmf_pcie_reset_device() after the
chip recognition is done. So the faulty watchdog reset can be
removed as it was causing driver reload to fail and hang the
system requiring a power-cycle. Instead the call to to the
brcmf_pcie_reset_device() function is done twice in the unload.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: remove chipinfo debugfs entry

The information provided by chipinfo is also provided by the
revinfo debugfs entry. Removing it from debugfs.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Update msgbuf read pointer quicker.

On device to host data using msgbuf the read pointer gets updated
once all data is processed. Updating this pointer more frequently
allows the firmware to add more data quicker. This will result in
slightly higher and more stable throughput on CPU bounded host
processors.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8192c: Add init codes for "fw_version" and "fw_subversion".

The variable "fw_version" is used in the _ResetDigitalProcedure1().
but It is not initialized. so I add init codes for "fw_version" and
"fw_subversion".

Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8192cu: Fix variable isfirst_ampdu

rtl92cu_rx_query_desc set a isampdu twice.
but second code is related to isfirst_ampdu.
so i change it.

Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8192cu: debug message change "RTL8192CE" to "RTL8192CU"

In the rtlwifi/rtl8192cu, I change debug message "RTL8192CE" to
"RTL8192CU".

Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8192cu: remove duplicated routine in _rtl92c_phy_rf6052_config_parafile

in the _rtl92c_phy_rf6052_config_parafile(), cases
RF90_PATH_A and RF90_PATH_B call the same routine.
so i remove one of these routine. also the return
routine is duplicated. so i remove it.

Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: fix tm_trigger usage

While working on getting my rtl8821au driver in pretty shape for
inclusion, it is dicosvered that the tm_trigger flag is used only for
the first device using this driver.
This flag handles the thermal power management in the hardware.

To change this add a entry in sttruct rtl_dm, so each device can handle
is separately.

Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8192cu: remove INTF_PCI and INTF_USB

in the rtlwifi/rtl8192cu, INTF_PCI and INTF_USB is unnecessary.
because RTL8192CU chipset is only USB interface.

Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8192cu: remove _InitBeaconParameters().

_InitBeaconParameters() and rtl92cu_init_beacon_parameters() is
same routine. I remove both functions. then i add
_rtl92cu_init_beacon_parameters() in the hw.c.
_rtl92cu_init_beacon_parameters() is same routine with
_InitBeaconParameters().

Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8192cu: remove IS_HARDWARE_TYPE_8192CE and IS_HARDWARE_TYPE_8192CU

in the rtlwifi/rtl8192cu, IS_HARDWARE_TYPE_8192CE and IS_HARDWARE_TYPE_8192CU
is unnecessary. because rtlwifi/rtl8192cu codes aren't shared.

Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wil6210: reorder init sequence

Need to reorder init sequence to run wil_platform_init
before pci_enable_device. Assumption is platform init
may be required before device may be enabled.
Another issue, platform uninit should be called after
pci_disable_device because platform uninit may render
pci device non-accessible.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

wil6210: platform hooks for modile init/exit

Provide platform hooks for module init/exit.
If platform require to perform some specific actions
in global context, this is where to do so.

Example may be turning on power for the PCIE based
on DT information.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

wil6210: Support hidden SSID

Pass hidden SSID information to FW for proper operation.
In order to be able to scan/connect to the hidden SSID, SSID
setting is added when scan is requested from FW. SSID
scanning currently supports single SSID due to FW limitation.

Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

wil6210: add per-MCS Rx stats

Provide detailed statistics for the Rx frames per MCS
Statistics printed in "stations" debugfs entry

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

wil6210: add NIC memory region mac_rgf_ext

Firmware defines new memory region, mac_rgf_ext
that need to be accessed from the host for debug purposes.

Add corresponded mapping

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

wil6210: modparam for bcast ring size

Control Bcast ring size in similar way as Rx and Tx ones,
through "bcast_ring_order" modparam, actual ring size is 1 << order

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Fix multiple clients associating in AP mode

When one client is associated and connected to an ar6003 hw version
2.0 with firmware 3.1.1.149, and another client tries to connect, the
first client's MAC address is lost in the station list because the
"aid" is always "1".  The structure "wmi_connect_event" has the "aid"
as the second byte in the message, but it should be the first byte.

This patch has been tested with linux-3.10.40

Signed-off-by: Brent Taylor <motobud@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: prevent memory leak in wmi rx ops

Found during code review. This was pretty much
impossible to happen but better safe than sorry.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: fix channel switching

In the midst of chanctx patch review channel
switching became broken which I failed to notice
until now.

Function ath10k_mac_vif_chan() reports current
chandef which isn't updated until after
switch_vif_chanctx() is returned from.
Consequently the driver just restarted operation
on channels it was residing already instead of
switching to the new ones.

Fixes: 500ff9f9389d ("ath10k: implement chanctx API")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: remove ath10k_chanctx struct

In practice there's no point in having a copy of
chanctx_conf.

Most of the time the channel pointer (and band
along with it) is accessed and this can't change
after a chanctx is created because switching is
done using explicit chanctx swapping via
switch_vif_chanctx().

The only thing that can change within a
chanctx_conf and is used by the driver is
radar_enabled and channel width. These are however
always accessed in adequate mac80211 callback
context which guarantees safe access to the
chanctx data.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: fix ar->rx_channel updating logic

Channel contexts aren't iterable until after
they've been added to the driver. The code assumed
otherwise.

This problem could result in:

 * rx_channel being NULL and forcing Rx path to go
   the slow way to get channel on QCA988X,

 * report incorrect channel when running
   multi-channel on QCA61X4 hw2.1,

 * report incorrect channel after AP channel
   switch.

Fixes: 500ff9f9389d ("ath10k: implement chanctx API")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: remove unused variable 'id' in ath10k_pci_tx_pipe_cleanup()

mete_data is extracted from ce descriptor and stored in variable 'id'.
later, id is not used anywhere in the same function.

Fixes: d84a512dca23 ("ath10k: remove transfer_id from ath10k_hif_cb::tx_completion")

Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: free wmi mgmt event skb when parsing fails

When wmi mgmt event function fails to parse given skb,
it should be freed on failure condition to avoid memory
leaks. Found this during the code review.

Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

bcma: lower dependency of BCMA_DRIVER_PCI_HOSTMODE

This extension of BCMA_DRIVER_PCI has no reason to depend on
BCMA_HOST_PCI. User may just want to have PCI device attached to SoC
registered without enabling any extra client mode code.
This can be useful when having non-bcma PCI device attached or when
using other PCI driver.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

bcma: make calls to PCI hostmode functions config-safe

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

b43: fix support for 14e4:4321 PCI dev with BCM4321 chipset

It seems Broadcom released two devices with conflicting device id. There
are for sure 14e4:4321 PCI devices with BCM4321 (N-PHY) chipset, they
can be found in routers, e.g. Netgear WNR834Bv2. However, according to
Broadcom public sources 0x4321 is also used for 5 GHz BCM4306 (G-PHY).
It's unsure if they meant PCI device id, or "virtual" id (from SPROM).
To distinguish these devices lets check PHY type (G vs. N).

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: use direct data pointer in NVRAM parser struct

As we plan to add support for platform NVRAM we should store direct
data pointer without the extra struct firmware layer. This will allow
us to support other sources with the only requirement being u8 buffer.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mt7601u: set promiscous mode based on FIF_OTHER_BSS

Most drivers use FIF_OTHER_BSS to set promiscous mode.  Let us
follow their lead even though it doesn't match exactly the HW
filter flags.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mt7601u: don't cleanup device second time after .resume()

Make sure .disconnect() doesn't cleanup the device if
.resume() failed.  This may happen when device is removed
during suspend.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mt7601u: watch out for invalid-length frames

Users of older Ralink devices report that received frames
sometimes have zero length.  Watch out for that.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mt7601u: unify paged and non-paged RX dma paths

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: set wiphy perm_addr to hardware MAC address

This allows e.g. user space to use /sys/class/ieee80211/*/macaddress

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: support NVRAMs containing pci devpaths (instead of pcie)

Recently Broadcom added support for NVRAMs with entries for multiple
PCIe devices. One of the supported formats is based on prefixes defined
like: devpath0=pcie/1/4/ and entries like 0:foo=bar 0:baz=qux etc.

Unfortunately there are also a bit older devices using different way of
defining prefixes, e.g. SmartRG SR400ac (2 x BCM43602) with entries:
devpath0=pci/1/1/
devpath1=pci/2/1
Broadcom stated this old format will never be used/supported by brcmfmac
but given the simplicity of this patch I'll insist on supporting it.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: update current config_band info in start_ap

It was observed that AP beacons would not reflect correct regulatory
information upon starting AP in A band. This was because of missing
AP config band update in set_channel of start_ap.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: change debug dump issue since skb maybe null

This patch fixes semantic warning for debugging data dump feature.
Previous code is based on the assumption that skb is not null.
New change makes sure that we already have data buffer.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8192cu: Fix performance issue.

After physical reconnect, the rtl8192cu chipset shows low
transmission rates.It cause is that variable "iqk_initialized"
do not de-initialized. So I add this code.

Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: do not decrease tx_pending for AMSDU packet once more

Negative adapter->tx_pending is observed while running data traffic,
because tx_pending is decreased once more for AMSDU packet.

since tx_pending have been decreased for all the source MSDU packets,
we don't need to update once more for AMSDU packet.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: using right tid for addressing ra_list

This patch fixes issue with the accessing correct ra_list by
downgrading corresponding tid number.

Alternatively, ra lists are created in mwifiex_wmm_add_buf_txqueue
using downgraded tid number.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: update AP WMM settings from BSS_START event

This was missing and would cause issue in WMM handling.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: advertise PS ON by default support to cfg80211

This would enable driver to enter powersave as soon as connected.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: drop block-ack action frames

We often see ADDBA request packets coming to driver because driver
has registered for action frame subtype. We dont process BA action
frames in host; drop such frames.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Xinmin Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: support downloading IEs from tail

Earlier only RSN, WPA and channel switch IEs from tail buffer would
be downloaded to FW.
This patch adds support for downloading more IEs from tail buffer.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: parse power constraint IE from Tail

This patch adds support to parse power constraint IEs from
Tail buffer. This power constraint is then set to FW during
bss_config download.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: dump station support in uap mode

This patch extend cfg80211 dump_station handler, support for
dump stations associated to mwifiex micro AP.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: add sta_list firmware command

This patch add sta_list firmware command, which can be used
to get power status and rssi for the stations associated to
mwifiex micro AP.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: maintain station statistic in uap mode

This patch maintain statistic information for the stations associated
to the mwifiex micro AP, include tx/rx bytes/packets, signal strength,
tx bitrate.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: add cfg80211 get_channel handler

This patch add cfg80211 get_channel handler for mwifiex.
The handler will be used to report current channel to upper
layer utility.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: disable CAC upon radar detection event

This patch adds support to disable ongoing CAC in FW upon
detecting radar during CAC period.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: reset 11h active flag when chandef does not require dfs

This patch fixes an issue where we were still setting 11h_active
flag to true for channel defs where DFS is not required.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: enable 11d after bss reset

BSS reset would reset all state information in FW.
Issue 11d config command after reset to enabled 11d in FW.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: support AP reset after bss_stop

This would enable clearing of FW bss data structures when AP
operations are stopped.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: correct bss_type assignment

Correct bss_type assignment in add_virtual_interface.
This would ensure correct operation in multiple station scenarios.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: verbose logging for association failure messages

This patch adds more detailed information about association failures
 - reason and states.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath9k: fix DMA stop sequence for AR9003+

AR93xx and newer needs to stop rx before tx to avoid getting the DMA
engine or MAC into a stuck state.
This should reduce/fix the occurence of "Failed to stop Tx DMA" logspam.

Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wl1251: drop unneeded goto

Delete jump to a label on the next line, when that label is not
used elsewhere.

A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r@
identifier l;
@@

-if (...) goto l;
-l:
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

tcp: double default TSQ output bytes limit

Xen virtual network driver has higher latency than a physical NIC.
Having only 128K as limit for TSQ introduced 30% regression in guest
throughput.

This patch raises the limit to 256K. This reduces the regression to 8%.
This buys us more time to work out a proper solution in the long run.

Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: remove redundant checks

tcp_v4_rcv() checks the following before calling tcp_v4_do_rcv():

if (th->doff < sizeof(struct tcphdr) / 4)
    goto bad_packet;
if (!pskb_may_pull(skb, th->doff * 4))
    goto discard_it;

So following check in tcp_v4_do_rcv() is redundant
and "goto csum_err;" is wrong anyway.

if (skb->len < tcp_hdrlen(skb) || ...)
goto csum_err;

A second check can be removed after no_tcp_socket label for same reason.

Same tests can be removed in tcp_v6_do_rcv()

Note : short tcp frames are not properly accounted in tcpInErrs MIB,
because pskb_may_pull() failure simply drops incoming skb, we might
fix this in a separate patch.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'switchdev-next'

Scott Feldman says:

====================
switchdev: documentation updates

Update the switchdev documentation to clarify that for IPV4 FIB object, the add
op is used for both adding and modifying the FIB entry on the device.

I found a few other white-space and grammer issues to fix, and to clarify the
static FDB ops.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

switchdev: documentation: use switchdev_port_obj_xxx for IPv4 FIB add/modify/delete ops

Clarify in documentation and code that IPV4 FIB add operation is used for
both adding a new FIB entry to the device and for modifying an existing FIB
entry on the device.

Also, remove left-over references to ipv4_fib ops and replace with details
on SWITCHDEV_PORT_IPV4_FIB object.

Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

switchdev: documentation: for static FDB ops, use switchdev_port_fdb_xxx ops

Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

switchdev: documentation: fix grammer error

Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

switchdev: documentation: fix longer-than-80-char lines

Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2015-06-03' of git://git./linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
new driver mt7601u for MediaTek Wi-Fi devices MT7601U

ath10k:

* qca6174 power consumption improvements, enable ASPM etc (Michal)

wil6210:

* support Wi-Fi Simple Configuration in STA mode

iwlwifi:

* a few fixes (re-enablement of interrupts for certain new
  platforms that have special power states)
* Rework completely the RBD allocation model towards new
  multi RX hardware.
* cleanups
* scan reworks continuation (Luca)

mwifiex:

* improve firmware debug functionality

rtlwifi:

* update regulatory database

brcmfmac:

* cleanup and new feature support in PCIe code
* alternative nvram loading for router support
====================

Conflicts:
drivers/net/wireless/iwlwifi/Kconfig

Trivial conflict in iwlwifi Kconfig, two commits adding
the same two chip numbers to the help text, but order
transposed.

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'cxgb4-next'

Hariprasad Shenai says:

====================
cxgb4: Adds support for various ethtool stats

This patch series adds the following:
Adds support to dump adapter specific stats in ethtool
Adds support to dump channel stats in ethtool
Adds support to dump loopback port stats in ethtool
Remove wake-on-lan get/set ethtool support

This patch series has been created against net-next tree and includes
patches on cxgb4 driver.

We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4: Remove WOL get/set ethtool support

Remove ethtool get/set support for wake on lan, adapter doesn't support
it.

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4: Add support to dump loopback port stats

Add support in ethtool to dump loopback port statistics

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4: Add support in ethtool to dump channel stats

Add support in ethtool to dump adapter channel stats

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4: Add ethtool support to get adapter stats

Add ethtool support to get adapter specific hardware statistics

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge

Antonio Quartulli says:

====================
pull request: batman-adv 20150603

here you have our second batch of patches intended for net-next.

In this patchset you won't find any new features, but quite some code
cleanup work, a bunch of code style fixes and also comments corrections
by Markus Pargmann.

Moreover you have a patch from Sven Eckelmann removing an unnecessary
NULL check in batadv_iv_ogm_update_seqnos().

Please pull or let me know of any problem!
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: tulip: rearrange order of searching for substrings

Currently, two of the branches are dead code, since an earlier smaller
substring would have been found ("TP" in the "TP_NW" case and either
of "BNC" and "AUI" in the "BNC_AUI" case). Rearrange the strstr()
calls so that the longer strings are searched for first.

Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/jkirsher/next-queue

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2015-06-03

This series contains updates to e1000e only.

Yanir provides 8 fixes and 1 version bump for e1000e.  First fix resolves
a possible unit hang if multiple descriptors are available in the rings
during reset or runtime suspend.  Fixed a warning on SPARC compile based
on a suggested solution from Alex Duyck.  Fixed a logical error, where
a "if" condition under which a flush should occur, was revered.  Fixed
a hardware issue that prevented i219 from working in legacy interrupts
mode.  Fixed the hardware clock configuration and suprious non-linear
increment.  Lastly, fixed a system hang which occurred during execution
of "ethtool -t <NIC>", by disabling MULR for the loopback test to avoid
the hand state.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: introduce bpf_clone_redirect() helper

Allow eBPF programs attached to classifier/actions to call
bpf_clone_redirect(skb, ifindex, flags) helper which will
mirror or redirect the packet by dynamic ifindex selection
from within the program to a target device either at ingress
or at egress. Can be used for various scenarios, for example,
to load balance skbs into veths, split parts of the traffic
to local taps, etc.

Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx4_core: fix typo in mlx4_set_vf_mac

fix typo in mlx4_set_vf_mac

Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx4_core: need to call close fw if alloc icm is called twice

If mlx4_enable_sriov is called by adapter without this
feature MLX4_DEV_CAP_FLAG2_SYS_EQS then during this path the function alloc
icm is called twice without freeing the structures from the first time.

Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx4_core: double free of dev_vfs

If user loads mlx4_core with num_vfs greater than
supported then variable dev->dev_vfs is freed 2 times after unloading the
driver.

Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/dec/tulip/uli526x.c: fix misleading indentation in uli526x_timer

This code in drivers/net/ethernet/dec/tulip/uli526x.c
function "uli526x_timer":

  1086          } else
  1087                  if ((tmp_cr12 & 0x3) && db->link_failed) {
  [...snip...]
  1109                  }
  1110                  else if(!(tmp_cr12 & 0x3) && db->link_failed)
  1111                  {
  [...snip...]
  1117                  }
  1118                  db->init=0;

is misleadingly indented: the
  db->init=0
is indented as if part of the else clause at line 1086, but it is
independent of it (no braces before the "if" at line 1087).

This patch fixes the indentation to reflect the actual meaning of the code,
though is it actually meant to be part of the "else" clause?  (I'm a
compiler developer, not a kernel person).  It also adds spaces around
the assignment, to placate checkpatch.pl.

Seen via an experimental new gcc warning I'm working on for gcc 6,
-Wmisleading-indentation, using gcc r223098 adding
-Werror=misleading-indentation to KBUILD_CFLAGS in Makefile.
The experimental GCC emits this warning (as an error), rightly IMHO:

drivers/net/ethernet/dec/tulip/uli526x.c: In function ‘uli526x_timer’:
drivers/net/ethernet/dec/tulip/uli526x.c:1118:3: error: statement is
indented as if it were guarded by... [-Werror=misleading-indentation]
   db->init=0;
    ^
drivers/net/ethernet/dec/tulip/uli526x.c:1086:4: note: ...this ‘else’
clause, but it is not
  } else
     ^

Hope this is helpful
Dave

Signed-off-by: David Malcolm <dmalcolm@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: dp83867: Add TI dp83867 phy

Add support for the TI dp83867 Gigabit ethernet phy
device.

The DP83867 is a robust, low power, fully featured
Physical Layer transceiver with integrated PMD
sublayers to support 10BASE-T, 100BASE-TX and
1000BASE-T Ethernet protocols.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethernet: micrel: use time_after_eq

use the time_after_eq macro for jiffies comparison operation

Signed-off-by: Antonio Murdaca <antonio.murdaca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx4_core: Fix build failure introduced by the EQ pool changes

When CONFIG_RFS_ACCEL or SMP aren't set, we fail to build, fix it.

Also, avoid build warning as of unused function on that setup.

Fixes: c66fa19c405a ('net/mlx4: Add EQ pool')
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

batman-adv: Remove unnecessary ret variable in algo_register

Remove ret variable and all jumps.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>

batman-adv: Remove unnecessary ret variable

We can avoid this indirect return variable by directly returning the
error values.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>

batman-adv: main, batadv_compare_eth return bool

Declare the returntype of batadv_compare_eth as bool.
The function called inside this helper function
(ether_addr_equal_unaligned) also uses bool as return value, so there is
no need to return int.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>