Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next into for-davem

hyperv: Enable sendbuf mechanism on the send path

We send packets using a copy-free mechanism (this is the Guest to Host transport
via VMBUS). While this is obviously optimal for large packets,
it may not be optimal for small packets. Hyper-V host supports
a second mechanism for sending packets that is "copy based". We implement that
mechanism in this patch.

In this version of the patch I have addressed a comment from David Miller.

With this patch (and all of the other offload and VRSS patches), we are now able
to almost saturate a 10G interface between Linux VMs on Hyper-V
on different hosts - close to  9 Gbps as measured via iperf.

Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: stmmac: set phy to use polling by default

mii_irq[] array is never initialized anywhere in the driver, thus mii_irq[]
will always equate to zero. So, for the case where the PHY does not have an
irq, we should use PHY_POLL for that situation.

Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Tested-by: Vince Bridgers <vbridger@altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

virtio-net: Set needed_headroom for virtio-net when VIRTIO_F_ANY_LAYOUT is true

This is a small supplement for commit e7428e95a06fb516fac1308bd0e176e27c0b9287
("virtio-net: put virtio-net header inline with data"). TCP packages have
enough room to put virtio-net header in, but UDP packages do not. By
setting dev->needed_headroom for virtio-net device, UDP packages could have
enough room.

For UDP packages, sk_buff is alloced in fun __ip_append_data. The size is
"alloclen + hh_len + 15", and "hh_len = LL_RESERVED_SPACE(rt-dst.dev);".
The Macro is defined as follows:
#define LL_RESERVED_SPACE(dev) \
     ((((dev)->hard_header_len+(dev)->needed_headroom)\
     &~(HH_DATA_MOD - 1)) + HH_DATA_MOD)
By default, for UDP packages, after skb is allocated, only 16 bytes
reserved. And 2 bytes remained after mac header is set. That is not enough
to put virtio-net header in. If we set dev->needed_headroom to 12 or 10
(according to mergeable_rx_bufs is on or off ), more room can be reserved.
Then there is enough room for UDP packages to put the header in.

test result list as below:
guest and host: suse11sp3, netperf, intel 2.4GHz
+-------+---------+---------+---------+---------+
|       |   old             |   new             |
+-------+---------+---------+---------+---------+
| UDP   |  Gbit/s | pps     |  Gbit/s | pps     |
| 64    |  0.57   | 692232  |  0.61   | 742420  |
| 256   |  1.60   | 686860  |  1.71   | 733331  |
| 512   |  2.92   | 674576  |  3.07   | 710446  |
| 1024  |  4.99   | 598977  |  5.17   | 620821  |
| 1460  |  5.68   | 483757  |  7.16   | 610519  |
| 4096  |  6.98   | 637468  |  7.21   | 658471  |
+-------+---------+---------+---------+---------+

Signed-off-by: Zhang Jie <zhangjie14@huawei.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: fix memory leak of publications

Commit 1bb8dce57f4d15233688c68990852a10eb1cd79f ("tipc: fix memory
leak during module removal") introduced a memory leak issue: when
name table is stopped, it's forgotten that publication instances are
freed properly. Additionally the useless "continue" statement in
tipc_nametbl_stop() is removed as well.

Reported-by: Jason <huzhijiang@gmail.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ipv6: Introduce ip6_sk_dst_hoplimit.

This replaces 6 identical code snippets with a call to a new
static inline function.

Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: update DSA drivers to use ds_to_priv

Use the helper function to retrieve the driver private context instead of
using (void *)(ds + 1).

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: add ds_to_priv

DSA drivers have a trick which consists in allocating "priv_size" more
bytes to account for the DSA driver private context. Add a helper
function to access that private context instead of open-coding it in
drivers with (void *)(ds + 1).

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rsi: Changing opcode for sta mode according to changes in firmware

Signed-off-by: Jahnavi Meher <jahnavi.meher@redpinesignals.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix worse EVM for 11b rates

Adjust FIR filter co-efficients to improve EVM for 11b rates.

Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: update ar9300 initvals

 * rfsat gainchange hysteresis of rf_gain stuck with large
   interference present.

Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: complete radio 0x2056 setup

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Fix AR5K_PHY_TXPOWER_RATE_MAX register value setting.

I was reading ath5k power setting code and
noticed typing error in ath5k_hw_txpower function.
Invalid value was written to AR5K_PHY_TXPOWER_RATE_MAX
register.

Signed-off-by: Nikolay Ledovskikh <nledovskikh@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: Convert /n to \n

Use a newline character appropriately.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wlcore: fix usage of platform_device_add_data()

Coverity CID 986698 reports leakage of struct wlcore_platdev_data in the
probe functions of both the SPI/SDIO interfaces. The structure passed to
platform_device_add_data() is dynamically allocated and only freed in the
error paths, however, platform_device_add_data() adds a copy of the platform
specific data to the device. Move the temporary struct that is kmemdup'ed
to the stack. This issue exists since afb43e6d (wlcore: remove if_ops from
platform_data).

Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8723be: disable MSI interrupts mode

94010fa0dd07e8b904e7c6b6589f15573008ab15 ("rtlwifi: add MSI interrupts
mode support") introduced MSI interrupts mode support, which seemed
safe enough with RTL8188EE and RTL8723BE as RealTek's testing results,
but some users reported their RTL8188EE modules could not connect to
any wireless network after the MSI mode was enabled by Ubuntu 14.04.

So, let's fallback to pin-based mode until rtlwifi's MSI support get
good compatibility.

BugLink: https://bugs.launchpad.net/bugs/1310512
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Revert "rtlwifi: rtl8188ee: enable MSI interrupts mode"

This reverts commit 2a54eb5e1476426ee639bbfbe179b52342a0d82c
("rtlwifi: rtl8188ee: enable MSI interrupts mode").

94010fa0dd07e8b904e7c6b6589f15573008ab15 ("rtlwifi: add MSI interrupts
mode support") introduced MSI interrupts mode support, which seemed
safe enough with RTL8188EE and RTL8723BE as RealTek's testing results,
but some users reported their RTL8188EE modules could not connect to
any wireless network after the MSI mode was enabled by Ubuntu 14.04.

So, let's fallback to pin-based mode until rtlwifi's MSI support get
good compatibility.

BugLink: https://bugs.launchpad.net/bugs/1310512
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: don't pre-set radio_on variable to true

Setting it to true during init doesn't seem to be any workaround while
it can cause problems (not enabling radio due to belief it's enabled).

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: use b43_software_rfkill helper

This removes dealing with pointers directly and allows tracking radio
state with radio_on variable.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: bcma: respect GMODE (band choice) during core reset

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-john' of git://git./linux/kernel/git/jberg/mac80211-next

Conflicts:
net/mac80211/chan.c

Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth-next

Merge branch 'master' of git://git./linux/kernel/git/jkirsher/net-next

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to i40e and i40evf.

Jacob provides a i40e patch to remove ptp_tx_work() because it conflicts
with the interrupt-based handler and will cause spurious warning messages
to be displayed in the kernel log.  Since the hardware can properly trigger
an interrupt, we do not need to poll for an available timestamp in a work
queue any more.

Greg provides two patches for i40e, first to retain the MAC filter list
when changing a port VLAN.  Second fixes an issue where the function to
set the VF MAC address was not taking the port VLAN filter into account
when setting/clearing/resetting the VF's host administered MAC address.

Mitch provides three patches for i40evf, first adds support for getting
and setting RSS hashing options, RSS LUT entries, and getting the number
of device channels from ethtool.  Fixes a panic that woudl occur in the VF
if the PF driver failed or was removed from the host kernel.

Shannon adds driver version string to the driver version command so that
can be passed down through the firmware to low-level NC-SI functions.

Neerav provides several patches, first redistributes queue vectors after
DCB reconfiguration because the total number of queues that are configured
for a VSI may change based on a change in the total number of TCs enabled
as a result of a change in the DCB configuration based on DCBX.  Second,
allows the driver probe to continue when querying DCB config fails.
Lastly, provides changes to retrieve and store missing link config
information that was not being cached in the struct i40e_link_status.

Kevin provides a couple of patches, first to change a int variable type
to u16 to avoid a typecheck failure.  Second to update a function
parameters to remove an argument which is no longer used.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: move the delivery of named messages out of nametbl lock

Commit a89778d8baf19cd7e728d81121a294a06cedaad1 ("tipc: add support
for link state subscriptions") introduced below possible deadlock
scenario:

       CPU0                          CPU1
T0:   tipc_publish()                 link_timeout()
T1:   tipc_nametbl_publish()         [grab node lock]*
T2:   [grab nametbl write lock]*     link_state_event()
T3:   named_cluster_distribute()     link_activate()
T4:   [grab node lock]*              tipc_node_link_up()
T5:                                  tipc_nametbl_publish()
T6:                                  [grab nametble write lock]*

The opposite order of holding nametbl write lock and node lock on
above two different paths may result in a deadlock. If we move the
the delivery of named messages via link out of name nametbl lock,
the reverse order of holding locks will be eliminated, as a result,
the deadlock will be killed as well.

Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: fix out of bounds indexing

Commit 78acb1f9b898e85fa2c1e28e700b54b66b288e8d ("tipc: add
ioctl to fetch link names") introduced a buffer overflow bug where
specially crafted ioctl requests could cause out-of-bounds indexing
of the node->links array. This was caused by an incorrect check vs
MAX_BEARERS, and the static code checker complaint is:
net/tipc/node.c:459 tipc_node_get_linkname() error: buffer overflow 'node->links' 2 <= 2

Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ctc: replace PTR_RET with PTR_ERR_OR_ZERO

PTR_RET is deprecated. Do not recommend its usage anymore.
Use PTR_ERR_OR_ZERO instead.

Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

claw: replace PTR_RET with PTR_ERR_OR_ZERO

PTR_RET is deprecated. Do not recommend its usage anymore.
Use PTR_ERR_OR_ZERO instead.

Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth: Add new priority queueing options

The existing options for priority queueing within OSA devices were based on
the now partially defunct TOS field. This patch adds two new options as
follows:
   - prio_queueing_skb: bases priority queueing on skb-priority
   - prio_queueing_vlan: uses the priority code point in the 802.1Q header

Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth: Extend priority queueing to IPv6

Make the current priority queueing logic apply to IPv6 traffic.

Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth: replace PTR_RET with PTR_ERR_OR_ZERO

PTR_RET is deprecated. Do not recommend its usage anymore.
Use PTR_ERR_OR_ZERO instead.

Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lcs: replace PTR_RET with PTR_ERR_OR_ZERO

PTR_RET is deprecated. Do not recommend its usage anymore.
Use PTR_ERR_OR_ZERO instead.

Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth: Fix default queue setting in priority queueing

The default queue for queueing modes prio_queueing_prec and
prio_queueing_tos is supposed to be QETH_DEFAULT_QUEUE. However, neither
mode will reset the default default_out_queue value when enabled, leaving
a previously set value activate as the default.
E.g. enabling one of the fixed queueing modes, e.g. no_prio_queueing:0,
and successively switching to any of the prio_queueing_* modes will
leave default_out_queue at the previous (wrong) value 0.

Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ptp: validate the requested frequency adjustment.

PTP Hardware Clock drivers specify a maximum frequency adjustment that
their clocks can accommodate. Normally, user space programs will want to
respect the advertised limits. However, no kernel or driver code checks
that the dialed frequency offset is within the bounds, and out of range
values can lead to surprising results.

This patch fixes the issue by rejecting bad values.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: Use predefined value for readability

Signed-off-by: Hisao Tanabe <xtanabe@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool: exit the loop when invalid index occurs

The commit 3de0b592394d ("ethtool: Support for configurable RSS hash
key") introduced a new function ethtool_copy_validate_indir() with
full iteration of the loop to validate the ring indices, which could
be an overkill. To minimize the impact, we ought to exit the loop as
soon as the invalid index occurs for the very first time. The
remaining loop simply doesn't serve any more purpose.

Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Cc: Venkata Duvvuru <VenkatKumar.Duvvuru@Emulex.Com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mac80211_hwsim: Advertise support for AP mode channel width changes

mac80211 takes care of all the needed steps for hwsim, so indicate
support for this capability.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: Support dynamic AP mode channel width changes

Implement the new cfg80211 capability to enable mac80211-based drivers
to support for dynamic channel bandwidth changes (e.g., HT 20/40 MHz
changes).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: Dynamic channel bandwidth changes in AP mode

This extends NL80211_CMD_SET_CHANNEL to allow dynamic channel bandwidth
changes in AP mode (including P2P GO) during a lifetime of the BSS. This
can be used to implement, e.g., HT 20/40 MHz co-existence rules on the
2.4 GHz band.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: remove unnecessary assignment

P2P_DEVICE doesn't support ieee80211_bss_info_change_notify() for now,
so it's not needed to set changed flags for P2P_DEVICE.

Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: avoid calling useless channel context code

ieee80211_assign_chanctx() checks if local->use_chanctx is true, so
the two code block related to ieee80211_assign_chanctx() can be moved
into above if clause, emphasize that these code are executed only if
local->use_chanctx is true.

Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
[change subject]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

i40e/i40evf: Bump build version

Bump i40e to 0.3.46 and i40evf to 0.9.23.

Change-ID: Ia604ae6d513d9aaa8bfdac79665d9a3a72507df7
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e/i40evf: Retrieve and store missing link config information

Some information returned via "Get Link Status" command was not
being cached in the struct i40e_link_status.
Add this so the driver can utilize this information as needed.

Change-ID: If084a0ae2a63b16b97572196b993742af2c67772
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Update function formal parameters

Change the formal parameters to remove argument which is no longer used.

Change-ID: I493b56eba74a1f396fa1b7d24c0a4acbe536b5bf
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Do not expose fd-sb commands from debugfs

Ethtool -k/-K can handle this so we do not need it in debugfs.

Change-ID: I9df692f10a60b71805f8f48d3b87c7da3820b2aa
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Do not enable NTUPLE feature control in MFP mode

Although NTUPLE feature control is disabled by default, do not
allow user to be able to change it.

Change-ID: I4c3f95fb6dbc56b1b6cc47116ea1f72de02bc99c
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Change variable type to avoid typecheck failure

Change the variable type to avoid compiler warning about int to u16
possible data truncation.

Change-ID: I5eb3b578c86513c9625ca32d2f0b57cc01d7dc98
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40evf: remove debugging message

If the PF driver fails or is removed from the host, the VF driver will
fill up its log with this message.

Change-ID: I67045f987f7c0d444d21ded403adc509343cdb8f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40evf: fix panic on PF driver fail

Fix a panic that would occur in the VF if the PF driver failed or was
removed from the host kernel. In this case, the VF driver calls
i40evf_close(), but this function does nothing because the driver is in
the resetting state. Because of this, the driver doesn't free its irqs
and causes a kernel panic when it tries to disable MSI-X.

Change-ID: If95644a89e554b4d7be0dca1b6add26f63047129
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Don't stop driver probe when querying DCB config fails

In case of any AQ command to query port's DCB configuration fails
during driver's probe time; the probe fails and returns an error.

This patch prevents this issue by continuing the driver probe even
when an error is returned.

Also, added an error message to dump the AQ error status to show what
error caused the failure to get the DCB configuration from firmware.

Change-ID: Ifd5663512588bca684069bb7d4fb586dd72221af
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Redistribute queue vectors after DCB reconfiguration

The queue vectors are originally distributed among the total
number of queues that are configured for a given VSI. The number
of queues that are configured for a VSI depends on the number of
TCs that are enabled for the VSI at VSI setup/creation time.

But, the total number of queues that are configured for a VSI may
change based on change in the total number of TCs enabled as a
result of change in DCB configuration based on DCBX.

Hence, it is required for the queue vectors to be redistributed
when the total queues that are configured for a given VSI changes.

Without redistributing the vectors the queues that are configured
for the newly enabled TCs may not be able to do any Tx/Rx.

Change-ID: I4e780903db019e6199c7ce43627cef22c916acfe
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e/i40evf: add driver version string to driver version command

The driver version string was added to this struct to be passed
down through the firmware to low-level NC-SI functions. We tell
the firmware about the length of the ASCII string not counting
any terminating null.

Change-ID: I09ac98ff9b869e8661c55fc6a5c98808fc280c91
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Anjali Singhai <anjali.singhai@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Use port VLAN in MAC/VLAN filter configuration

The function to set the VF MAC address was not taking the port VLAN
filter into account when setting/clearing/resetting the VF's host
administered MAC address.  Be sure to use the port VLAN for VF MAC
filtering configurations.

Change-ID: I12595331981c79529738f041dcdbdb667ef8f5e6
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40evf: support ethtool RSS options

Add support for getting and setting RSS hashing options, RSS LUT
entries, and getting the number of device channels from ethtool. Because
the LUT is so small for the VFs, we just read and write the device
registers directly instead of maintaining a shadow copy.

Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Retain MAC filters when changing port VLAN

We were already taking care to retain the MAC filter list when deleting a
port VLAN.  Take some additional care to retain the MAC filter list when
changing a port VLAN.

Change-ID: Iacf9599ea24ecb4dca8e419aacaf4b58ca361a9c
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: remove ptp_tx_work timestamp work item

This patch removes the unnecessary ptp_tx_work item. It conflicts with
the interrupt-based handler, and will cause spurious warning messages to
be displayed in the kernel log. Since the hardware can properly trigger
an interrupt, we do not need to poll for an available timestamp in a
work queue any more.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

sched, act: allow to clear all actions as well

When we change the list of action on a given filter, currently we don't
change it to empty. This is a bug, we should allow to change to whatever
users given.

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sched, cls: check if we could overwrite actions when changing a filter

When actions are attached to a filter, they are a part of the filter
itself, so when changing a filter we should allow to overwrite the actions
inside as well.

In my specific case, when I tried to _append_ a new action to an existing
filter which already has an action, I got EEXIST since kernel refused
to overwrite the existing one in kernel.

This patch checks if we are changing the filter checking NLM_F_CREATE flag
(Sigh, filters don't use NLM_F_REPLACE...) and then passes the boolean down
to actions. This fixes the problem above.

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'qlcnic-next'

Jitendra Kalsaria says:

====================
qlcnic driver updates

This patch series containes following changes -
* Optimize MAC learning code.
* Export board temperature using hwmon-sysfs interface.
* Add support for configuring Tx interrupt coalescing parameters from VF.
* Logging error messages in error path.
* Restrict extended vNIC support in legacy interrupt mode and log appropriate
  message.

Please apply this series to net-next.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: Update version to 5.3.58

Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: Limit vNIC support in legacy interrupt mode

o When the driver loads in legacy interrupt mode, only vNICs
  with PCI function number 0-7 are supported.

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: Add driver logs in error path.

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: Allow setting TX interrupt coalescing parameters from VF.

o Tx interrupt coalescing parameters can now be set from VF.
o Added validation code in PF to validate the parameters.

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: Add hwmon interface to export board temperature.

Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: Optimize MAC learning code

* Use rx_mac_learn instead of mac_learn and eSwitch flag check in Rx path of
  82xx adapter.
* Check for MAC filter overrun only after driver scans through cached MAC address list.
  This will help to update the time stamp of cached MAC addresses even if
  adapter runs out of MAC address filter limit.
* Remove expensive log thrown by driver when MAC address filters are exhausted

Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: Use pci_enable_msix_exact() instead of pci_enable_msix()

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range()  or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.

Cc: Shahed Shaikh <shahed.shaikh@qlogic.com>
Cc: Dept-HSGLinuxNICDev@qlogic.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

FDDI: Reformat <linux/if_fddi.h> for 8-character tabs

Some of our FDDI support code has been apparently written with an
assumption that tabs are 4-character wide.  In preparation to the next
change this update reformats <linux/if_fddi.h> so that it stays within 79
columns and otherwise renders correctly with 8-character tabs.  No
functional change.

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: fix a possible memory leak

The commit a8b9b96e959f3c035af20b1bd2ba67b0b7269b19 ("tipc: fix race
in disc create/delete") leads to the following static checker warning:

net/tipc/discover.c:352 tipc_disc_create()
warn: possible memory leak of 'req'

The risk of memory leak really exists in practice. Especially when
it's failed to allocate memory for "req->buf", tipc_disc_create()
doesn't free its allocated memory, instead just directly returns
with ENOMEM error code. In this situation, memory leak, of course,
happens.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlge: Convert /n to \n

Use a newline character appropriately.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'systemport'

Florian Fainelli says:

====================
net: Broadcom SYSTEMPORT driver

This patchset adds support for the Broadcom SYSTEMPORT Ethernet MAC
controller which is used in the latest Broadcom BCM7xxx Set Top Box
System-on-a-Chip. This Ethernet MAC is interfaced to an internal
switch which will get a separate driver submitted later on.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

MAINTAINERS: add Broadcom SYSTEMPORT driver entry

Add an entry in the MAINTAINERS file listing myself as the maintainer
for the Broadcom SYSTEMPORT Ethernet MAC controller driver.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: systemport: hook SYSTEMPORT driver in the build

Hook the Broadcom SYSTEMPORT driver into the build system under the
SYSTEMPORT Kconfig symbol.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation: add Broadcom SYSTEMPORT Device Tree bindings

Add the Device Tree bindings documentation for the Broadcom SYSTEMPORT
Ethernet MAC controller hardware.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver

SYSTEMPORT is the latest Ethernet MAC hardware block used on newer
BCM7xxx Set Top Box SoCs in conjunction with an internal Ethernet
switch. This patch adds support for this hardware block along with the
following hardware features:

- support for hardware checksum offload (transmit and receive)
- support for the 32 transmit queues
- MIB counters reading

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/jkirsher/net-next

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to igb only.

Carolyn provides a number of cleanups to fix checkpatch warnings/errors
and two minor issues found by coccicheck.

v2: update patch indentation for patch 07 of the series based on feedback
    from David Miller.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

inetpeer_gc_worker: trivial cleanup

Do not initialize list twice.
list_replace_init() already takes care of initializing list.
We don't need to initialize it with LIST_HEAD() beforehand.

Signed-off-by: xiao jin <jin.xiao@intel.com>
Reviewed-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net_namespace: trivial cleanup

Do not initialize net_kill_list twice.
list_replace_init() already takes care of initializing net_kill_list.
We don't need to initialize it with LIST_HEAD() beforehand.

Signed-off-by: xiao jin <jin.xiao@intel.com>
Reviewed-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-next-for-3.16-20140425' of git://gitorious.org/linux-can/linux-can-next

Marc Kleine-Budde says:

====================
this is a pull request of 10 patches for net-next/master.

It consists of three patches by Alexander Shiyan, which improve the
mcp251x driver. Stefano Babic's patch move the SPI driver into a sub
folder. The three patches by Olivier Sobrie add support for the Kvaser
Leaf v2 and usb mini PCIe hardware to the existing driver. Alexander
Stein contributes eg20t support to the c_can pci driver. Together with
the patches on the net-tree, we'll be able to remove the pch_can driver
soon. Kurt Van Dijck's two patches clean up the sysfs attributes of the
softing driver.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'at86rf230-next'

Alexander Aring says:

====================
at86rf230 cleanup

this is the first patch series to cleanup the at86rf230 driver. Later I want
to implement regmap and a asynchron spi handling for transmit and receiving
frames.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

at86rf230: remove function for setting irq polarity

The function is small enough, we don't need a extra function for this.

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

at86rf230: remove unnecessary state read

This patch removes a unnecessary state read. The status value is never
evaluate after reading the state.

Also rename the status variable to dvdd, because this variable will be
used later.

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

at86rf230: remove unnecessary spi_set_drvdata

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

at86rf230: reset irq line before irq request

This patch resets the irq line before we are requesting the irq. This
avoids pending interrupts before requesting.

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

at86rf230: remove unnecessary assign

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

at86rf230: remove #ifdef CONFIG_OF

This is already handled by the of_match_ptr macro.

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

at86rf230: add at86rf230_device_id table

This patch adds a at86rf230_device_id table to offers various module
aliases.

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

at86rf230: make of_device_id const

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

at86rf230: add missing MODULE_DEVICE_TABLE

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

at86rf230: use devm_gpio_request_one

This patch replace the gpio_request functions with devm_gpio_request_one
functions. Then we don't need to take care about freeing gpios.

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

at86rf230: use devm_request_irq

This patch replace request_irq with devm_request_irq. With
devm_request_irq we don't need to care about freeing the irq.

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

at86rf230: remove irq_type in request_irq

We don't need to set these values at request_irq. The interrupt line is
already configured to same value like irq_get_trigger_type returned.

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

devicetree: add at86rf230 bindings

This patch adds devicetree bindings for the at86rf230 IEEE 802.15.4 SPI
device driver.

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

at86rf230: use irq_get_trigger_type

This patch removes the platform data for the irq_type. We use instead
the irq_get_trigger_type function to get these flags which should
already configured by the interrupt controller.

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'tipc-next'

Erik Hugne says:

====================
tipc: add support for link state subscriptions

Low level topology information like TIPC link up/down is useful for
applications like teamd to make smarter failover decisions in a
HA cluster environment. Fetching logical link names through an ioctl
may hurt the eyes of some. Suggestions for a more elegant way of doing
this would be appreciated in that case. :)

v2:
   -Properly based on net-next
   -Off-list comments from Billie Alsup:
    -Add a string length parameter to tipc_node_get_linkname
    -Use TIPC_MAX_LINK_NAME definition instead of hardcoded
     value in tipc_sioc_ln_req linkname
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: add ioctl to fetch link names

We add a new ioctl for AF_TIPC that can be used to fetch the
logical name for a link to a remote node on a given bearer. This
should be used in combination with link state subscriptions.
The logical name size limit definitions are moved to tipc.h, as
they are now also needed by the new ioctl.

Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: add support for link state subscriptions

When links are established over a bearer plane, we create a node
local publication containing information about the peer node and
bearer plane. This allows TIPC applications to use the standard
TIPC topology server subscription mechanism to get notifications
when a link goes up or down.

Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cfg80211: Use 5MHz bandwidth by default when checking usable channels

Current code checks if the 20MHz bandwidth is allowed for
particular channel -- if it is not, the channel is disabled.
Since we need to use 5/10 MHz channels, this code is modified in
the way that the default bandwidth to check is 5MHz. If the
maximum bandwidth allowed by the channel is smaller than 5MHz,
the channel is disabled. Otherwise the channel is used and the
flags are set according to the bandwidth allowed by the channel.

Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: Add attributes describing prohibited channel bandwidth

Since there are frequency bands (e.g. 5.9GHz) allowing channels
with only 10 or 5 MHz bandwidth, this patch adds attributes that
allow keeping track about this information.

When channel attributes are reported to user-space, make sure to
not break old tools, i.e. if the 'split wiphy dump' is enabled,
report the extra attributes (if present) describing the bandwidth
restrictions.  If the 'split wiphy dump' is not enabled,
completely omit those channels that have flags set to either
IEEE80211_CHAN_NO_10MHZ or IEEE80211_CHAN_NO_20MHZ.

Add the check for new bandwidth restriction flags in
cfg80211_chandef_usable() to comply with the restrictions.

Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: change return value of notifier function

Return NOTIFY_DONE if we don't care this time's notification, return
NOTIFY_OK if we successfully handled this time's notification. That's
the formal way to do it.

Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: change return value of notifier function

Return NOTIFY_DONE if we don't care this time's notification, return
NOTIFY_OK if we successfully handled this time's notification. That's
the formal way to do it.

Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: change wiphy_to_dev function name

Name wiphy_to_rdev is more accurate to describe what the function
does, i.e., return a pointer pointing to struct
cfg80211_registered_device.

Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>