GitHub/exynos8895/android_kernel_samsung_universal8895.git
10 years agoqlcnic: Add VXLAN Tx offload support
Shahed Shaikh [Fri, 21 Mar 2014 08:41:16 +0000 (04:41 -0400)]
qlcnic: Add VXLAN Tx offload support

This patch adds LSO, LSO6 and Tx checksum offload support for VXLAN
encapsulated packets on 83xx/84xx series adapters.

Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agogianfar: Fix P1010 config regression (SQ polling)
Claudiu Manoil [Fri, 21 Mar 2014 07:33:17 +0000 (09:33 +0200)]
gianfar: Fix P1010 config regression (SQ polling)

The P1010 device tree restricts the number of
supported interrupt groups to 1, although the eth
controller can support 2 interrupt groups and the
driver assumes the Multi-Group mode ("fsl,etsec2" model).

So, in this case the assumption that the Multi-Group
mode (MQ_MG_MODE) devices always support 2 interrupt
groups is false.  To fix this, a check for the actual
number of interrupt groups enabled in the board's
device tree has been added in gfar_probe for the
"fsl,etsec2" devices.

Without this fix, P1010 based boards claim support for
2 Tx queues to the net stack but only one is actually
allocated, leading to NULL access in xmit.  This issue
was introduced by enabling Single-Queue polling for
the P1010 devices.
(71ff9e3 gianfar: Use Single-Queue polling for
"fsl,etsec2")

Fixes: 71ff9e3df7e1c5d3293af6b595309124e8c97412
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoipv4: remove ipv4_ifdown_dst from route.c
Li RongQing [Mon, 24 Mar 2014 03:03:10 +0000 (11:03 +0800)]
ipv4: remove ipv4_ifdown_dst from route.c

ipv4_ifdown_dst does nothing after IPv4 route caches removal,
so we can remove it.

Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agonet: optimize csum_replace2()
Eric Dumazet [Mon, 24 Mar 2014 02:51:36 +0000 (19:51 -0700)]
net: optimize csum_replace2()

When changing one 16bit value by another in IP header, we can adjust
the IP checksum by doing a simple operation described in RFC 1624, as
reminded by David.

csum_partial() is a complex function on x86_64, not really suited for
small number of checksummed bytes.

I spotted csum_partial() being in the top 20 most consuming functions
(more than 1 %) in a GRO workload, which was rather unexpected.

The caller was inet_gro_complete() doing a csum_replace2() when
building the new IP header for the GRO packet.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoMerge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
David S. Miller [Sat, 22 Mar 2014 19:00:22 +0000 (15:00 -0400)]
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge

Antonio Quartulli says:

====================
Included changes:
- use ether_addr_copy instead of memcpy when possible
- implement new multicast packet optimisation
- improve several kerneldoc sections
- minor code cleanups

here you have our patchset for net-next/linux-3.15.  They are 16
patches but most of them are just small cleanups and kerneldoc
improvements.

The only big change is the one from patch 8 to 13 by Linus Lüssing
that introduces a new multicast packets optimisation. This new
component aims to reduce the air overhead by sending multicast packets
as bat-unicast when only one destination exists or by dropping them
directly at the source if the multicast group is totally empty.

In patch 11 Linus introduces an atomic_t variable, that like others
that we already have is only object of write and read, thus making the
atomic characteristic totally useless.  Unfortunately this is part of
our sysfs framework, that helps the developer to introduce new knobs
by using few macros only. For this reason we decided to keep Linus'
new knob for now, but I'd like to let you know that we are in the
process of re-working such framework in order to convert all the
current (useless) atomic_t to boolean in one go.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agobatman-adv: Start new development cycle
Simon Wunderlich [Thu, 13 Mar 2014 11:16:01 +0000 (12:16 +0100)]
batman-adv: Start new development cycle

Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
10 years agobatman-adv: improve DAT documentation
Antonio Quartulli [Sat, 22 Feb 2014 16:02:38 +0000 (17:02 +0100)]
batman-adv: improve DAT documentation

Add missing documentation for BATADV_DAT_ADDR_MAX and
convert an existing documentation to kerneldoc

Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
10 years agobatman-adv: improve the TT flags documentation
Antonio Quartulli [Sat, 22 Feb 2014 15:48:14 +0000 (16:48 +0100)]
batman-adv: improve the TT flags documentation

Convert the current documentation for the TT flags in proper
kerneldoc and improve it by adding an explanation for each
of the flags.

Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
10 years agobatman-adv: Send multicast packets to nodes with a WANT_ALL flag
Linus Lüssing [Sat, 15 Feb 2014 16:47:54 +0000 (17:47 +0100)]
batman-adv: Send multicast packets to nodes with a WANT_ALL flag

With this patch a node sends IPv4 multicast packets to nodes which
have a BATADV_MCAST_WANT_ALL_IPV4 flag set and IPv6 multicast packets
to nodes which have a BATADV_MCAST_WANT_ALL_IPV6 flag set, too.

Why is this needed? There are scenarios involving bridges where
multicast report snooping and multicast TT announcements are not
sufficient, which would lead to packet loss for some nodes otherwise:

MLDv1 and IGMPv1/IGMPv2 have a suppression mechanism
for multicast listener reports. When we have an MLDv1/IGMPv1/IGMPv2
querier behind a bridge then our snooping bridge is potentially not
going to see any reports even though listeners exist because according
to RFC4541 such reports are only forwarded to multicast routers:

-----------------------------------------------------------
            ---------------
{Querier}---|Snoop. Switch|----{Listener}
            ---------------
                       \           ^
                      -------
                      | br0 |  <  ???
                      -------
                          \
                     _-~---~_
                 _-~/        ~-_
                ~   batman-adv  \-----{Sender}
                \~_   cloud    ~/
                   -~~__-__-~_/

I)  MLDv1 Query:  {Querier}  -> flooded
II) MLDv1 Report: {Listener} -> {Querier}

-> br0 cannot detect the {Listener}
=> Packets from {Sender} need to be forwarded to all
   detected listeners and MLDv1/IGMPv1/IGMPv2 queriers.

-----------------------------------------------------------

Note that we do not need to explicitly forward to MLDv2/IGMPv3 queriers,
because these protocols have no report suppression: A bridge has no
trouble detecting MLDv2/IGMPv3 listeners.

Even though we do not support bridges yet we need to provide the
according infrastructure already to not break compatibility later.

Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
10 years agobatman-adv: Add IPv4 link-local/IPv6-ll-all-nodes multicast support
Linus Lüssing [Sat, 15 Feb 2014 16:47:53 +0000 (17:47 +0100)]
batman-adv: Add IPv4 link-local/IPv6-ll-all-nodes multicast support

With this patch a node may additionally perform the dropping or
unicasting behaviour for a link-local IPv4 and link-local-all-nodes
IPv6 multicast packet, too.

The extra counter and BATADV_MCAST_WANT_ALL_UNSNOOPABLES flag is needed
because with a future bridge snooping support integration a node with a
bridge on top of its soft interface is not able to reliably detect its
multicast listeners for IPv4 link-local and the IPv6
link-local-all-nodes addresses anymore (see RFC4541, section 2.1.2.2
and section 3).

Even though this new flag does make "no difference" now, it'll ensure
a seamless integration of multicast bridge support without needing to
break compatibility later.

Also note, that even with multicast bridge support it won't be possible
to optimize 224.0.0.x and ff02::1 towards nodes with bridges, they will
always receive these ranges.

Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
10 years agobatman-adv: Modified forwarding behaviour for multicast packets
Linus Lüssing [Sat, 15 Feb 2014 16:47:52 +0000 (17:47 +0100)]
batman-adv: Modified forwarding behaviour for multicast packets

With this patch a multicast packet is not always simply flooded anymore,
the behaviour for the following cases is changed to reduce
unnecessary overhead:

If all nodes within the horizon of a certain node have signalized
multicast listener announcement capability then an IPv6 multicast packet
with a destination of IPv6 link-local scope (excluding ff02::1) coming
from the upstream of this node...

* ...is dropped if there is no according multicast listener in the
  translation table,
* ...is forwarded via unicast if there is a single node with interested
  multicast listeners
* ...and otherwise still gets flooded.

Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
10 years agobatman-adv: Announce new capability via multicast TVLV
Linus Lüssing [Sat, 15 Feb 2014 16:47:51 +0000 (17:47 +0100)]
batman-adv: Announce new capability via multicast TVLV

If the soft interface of a node is not part of a bridge then a node
announces a new multicast TVLV: The existence of this TVLV
signalizes that this node is announcing all of its multicast listeners
via the translation table infrastructure.

Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
10 years agobatman-adv: introduce capability initialization bitfield
Linus Lüssing [Sat, 15 Feb 2014 16:47:50 +0000 (17:47 +0100)]
batman-adv: introduce capability initialization bitfield

The new bitfield allows us to keep track whether capability subsets of
an originator have gone through their initialization phase yet.

The translation table is the only user right now, but a new one will be
added soon.

Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
10 years agobatman-adv: Multicast Listener Announcements via Translation Table
Linus Lüssing [Sat, 15 Feb 2014 16:47:49 +0000 (17:47 +0100)]
batman-adv: Multicast Listener Announcements via Translation Table

With this patch a node which has no bridge interface on top of its soft
interface announces its local multicast listeners via the translation
table.

Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
10 years agobatman-adv: add kerneldoc for dst_hint argument
Antonio Quartulli [Sat, 15 Feb 2014 10:58:01 +0000 (11:58 +0100)]
batman-adv: add kerneldoc for dst_hint argument

Some helper functions used along the TX path have now a new
"dst_hint" argument but the kerneldoc was missing.

Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
10 years agobatman-adv: call unregister_netdev() to have it handle the locking for us
Marek Lindner [Sat, 8 Feb 2014 15:28:18 +0000 (23:28 +0800)]
batman-adv: call unregister_netdev() to have it handle the locking for us

Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
10 years agobatman-adv: fix a few kerneldoc inconsistencies
Simon Wunderlich [Fri, 24 Jan 2014 21:16:25 +0000 (22:16 +0100)]
batman-adv: fix a few kerneldoc inconsistencies

Reported-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
10 years agobatman-adv: prefer ether_addr_copy to memcpy
Antonio Quartulli [Tue, 21 Jan 2014 23:42:11 +0000 (00:42 +0100)]
batman-adv: prefer ether_addr_copy to memcpy

On some architectures ether_addr_copy() is slightly faster
than memcpy() therefore use the former when possible.

Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
10 years agobatman-adv: remove obsolete skb_reset_mac_header() in batadv_bla_tx()
Linus Lüssing [Sun, 19 Jan 2014 21:22:46 +0000 (22:22 +0100)]
batman-adv: remove obsolete skb_reset_mac_header() in batadv_bla_tx()

Our .ndo_start_xmit handler (batadv_interface_tx()) can rely on having
the skb mac header pointer set correctly since the following commit
present in kernels >= 3.9:

"net: reset mac header in dev_start_xmit()" (6d1ccff627)

Therefore this commit removes the according, now redundant,
skb_reset_mac_header() call in batadv_bla_tx().

Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
10 years agobatman-adv: use vlan_/eth_hdr() instead of skb->data in interface_tx path
Linus Lüssing [Sun, 19 Jan 2014 21:22:45 +0000 (22:22 +0100)]
batman-adv: use vlan_/eth_hdr() instead of skb->data in interface_tx path

Our .ndo_start_xmit handler (batadv_interface_tx()) can rely on having
the skb mac header pointer set correctly since the following commit
present in kernels >= 3.9:

"net: reset mac header in dev_start_xmit()" (6d1ccff627)

Therefore we can safely use eth_hdr() and vlan_eth_hdr() instead of
skb->data now, which spares us some ugly type casts.

At the same time set the mac_header in batadv_dat_snoop_incoming_arp_request()
before sending the skb along the TX path.

Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
10 years agobatman-adv: fix coccinelle warnings
Fengguang Wu [Mon, 6 Jan 2014 16:09:46 +0000 (17:09 +0100)]
batman-adv: fix coccinelle warnings

net/batman-adv/network-coding.c:1535:1-7: Replace memcpy with struct assignment

Generated by: coccinelle/misc/memcpy-assign.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
10 years agoMerge branch 'ptp-next'
David S. Miller [Fri, 21 Mar 2014 18:21:45 +0000 (14:21 -0400)]
Merge branch 'ptp-next'

Richard Cochran says:

====================
ptp: dynamic pin control

This patch series introduces a way of changing the auxiliary PTP
Hardware Clock functions (periodic output signals and time stamping
external signals) at run time. In the past on the netdev list, we have
discussed other ways to handle this, such as module parameters and
ethtool. This series implements a new PHC ioctl because that is the
most natural way. Users already activate the auxiliary functions via
the ioctls. The sysfs interface has also been expanded so that the pin
configuration can be programmed using shell scripts.

The first patch adds the new ioctls. The PHC subsystem does most of
the work of maintaining the function-to-pin mapping. Drivers will only
need to allocate and initialize a pin configuration table and also
provide a new method that validates a particular assignment.

Patches 5 and 6 just clean up a couple of issues in the phyter driver,
and the remaining patches actually hook the phyter's pins into the new
system.

* ChangeLog
** V3
   - simplify locking in the set pin logic
** V2
   - fix bug in sysfs code on init error path
   - rename ptp_setpin() to ptp_set_pinfunc()
   - rename .setpin() to .verify() in the driver interface
   - simplify ptp_find_pin() logic
   - use correct test when checking whether the pin with the
     calibration function is being reprogrammed
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agodp83640: let the periodic pin from the module parameter be a default.
Richard Cochran [Thu, 20 Mar 2014 21:22:00 +0000 (22:22 +0100)]
dp83640: let the periodic pin from the module parameter be a default.

This patch changes the driver use the new pin configuration method when
programming the periodic output signal.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agodp83640: let external input pins from the module parameters be defaults.
Richard Cochran [Thu, 20 Mar 2014 21:21:59 +0000 (22:21 +0100)]
dp83640: let external input pins from the module parameters be defaults.

This patch changes the driver to use the new pin configuration method when
programming the external time stamp input signals.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agodp83640: implement programmable pin functions.
Richard Cochran [Thu, 20 Mar 2014 21:21:58 +0000 (22:21 +0100)]
dp83640: implement programmable pin functions.

This patch adapts the dp83640 driver to allow reconfiguration of which
auxiliary function goes on which pin. The functions may be reassigned
freely with the one exception of the calibration function.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agodp83640: correct the periodic output frequency
Richard Cochran [Thu, 20 Mar 2014 21:21:57 +0000 (22:21 +0100)]
dp83640: correct the periodic output frequency

The phyter driver incorrectly feeds the value of the period into what
is in fact a pulse width register, resulting in the actual period
being twice the dialed value. This patch fixes the issue and renames a
variable to make the code at bit more clear.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agodp83640: trivial fixes
Richard Cochran [Thu, 20 Mar 2014 21:21:56 +0000 (22:21 +0100)]
dp83640: trivial fixes

This patch cleans up the input checking code on the external time stamp
function by using an unsigned rather than a signed channel index.

Also, this patch corrects the author's email address. When this macro
was last changed, the top level domain part of the email address was
left behind.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoptp: drivers: set the number of programmable pins.
Richard Cochran [Thu, 20 Mar 2014 21:21:55 +0000 (22:21 +0100)]
ptp: drivers: set the number of programmable pins.

This patch updates the many PTP Hardware Clock drivers with the
newly introduced field that advertises the number of programmable
pins. Some of these devices do have programmable pins, but the
implementation will have to wait for follow on patches.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoptp: expose the programmable pins via sysfs
Richard Cochran [Thu, 20 Mar 2014 21:21:54 +0000 (22:21 +0100)]
ptp: expose the programmable pins via sysfs

This patch adds the sysfs hooks needed in order to get and set the
programmable pin settings.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoptp: add the pin GET/SETFUNC ioctls to the testptp program.
Richard Cochran [Thu, 20 Mar 2014 21:21:53 +0000 (22:21 +0100)]
ptp: add the pin GET/SETFUNC ioctls to the testptp program.

This patch adds a option to the test program that lists the
programmable pins on a PTP Hardware Clock device, assuming there
are any such pins. A second option lets the user reprogram the
auxiliary function of a single pin.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoptp: introduce programmable pins.
Richard Cochran [Thu, 20 Mar 2014 21:21:52 +0000 (22:21 +0100)]
ptp: introduce programmable pins.

This patch adds a pair of new ioctls to the PTP Hardware Clock device
interface. Using the ioctls, user space programs can query each pin to
find out its current function and also reprogram a different function
if desired.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoMerge branch 'bcmgenet-next'
David S. Miller [Thu, 20 Mar 2014 21:36:23 +0000 (17:36 -0400)]
Merge branch 'bcmgenet-next'

Florian Fainelli says:

====================
net: bcmgenet: misc fixes

This patch series contains some misc. fixes for the bcmgenet driver.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agonet: bcmgenet: manipulate netdev_queue directly
Florian Fainelli [Thu, 20 Mar 2014 17:53:23 +0000 (10:53 -0700)]
net: bcmgenet: manipulate netdev_queue directly

Instead of always invoking netdev_get_tx_queue() in bcmgenet_xmit() and
bcmgenet_tx_reclaim(), just get the corresponding netdev_queue pointer
once and for all and manipulate it throughout bcmgenet_xmit() and
bcmgenet_tx_reclaim().

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agonet: bcmgenet: remove bogus tx queue checks
Florian Fainelli [Thu, 20 Mar 2014 17:53:22 +0000 (10:53 -0700)]
net: bcmgenet: remove bogus tx queue checks

netdev_pick_tx already takes care of making sure that a given
skb->queue_mapping value will remain within the number of advertised
hardware queue number, there is no need to re-do this again in the
driver.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agonet: bcmgenet: add skb_tx_timestamp call
Florian Fainelli [Thu, 20 Mar 2014 17:53:21 +0000 (10:53 -0700)]
net: bcmgenet: add skb_tx_timestamp call

The BCMGENET driver was not TX timestamping the SKBs it queued for
transmission, do this in bcmgenet_xmit() right before kicking the
Transmit DMA engine.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agonet: bcmgenet: remove unused spinlock member
Florian Fainelli [Thu, 20 Mar 2014 17:53:20 +0000 (10:53 -0700)]
net: bcmgenet: remove unused spinlock member

The spinlock cookie in bcmgenet_priv is never used, get rid of it.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoMerge branch 'sh_eth-next'
David S. Miller [Thu, 20 Mar 2014 21:22:20 +0000 (17:22 -0400)]
Merge branch 'sh_eth-next'

Laurent Pinchart says:

====================
sh_eth: Fix the race between open and MDIO bus registration

This patch series fixes the race condition that exists in the sh_eth driver
between network device open and MDIO bus registration. The actual fix is in
patch 4/5, with previous patches preparing the driver and patch 5/5 cleaning
up an unrelated issue.

I've based the idea on Sergei's attempt to fix the problem and can successfully
boot the Koelsch board over NFS with this series. I might have missed other
issues though, hence the RFC status.

The patches are based on top of the latest net-next master branch.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agosh_eth: Remove goto statements that jump straight to a return
Laurent Pinchart [Thu, 20 Mar 2014 14:00:35 +0000 (15:00 +0100)]
sh_eth: Remove goto statements that jump straight to a return

"goto" is well accepted for error paths in the kernel but should not be
used unnecessarily. Return the correct value directly instead of using a
goto when possible.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agosh_eth: Register MDIO bus before registering the network device
Laurent Pinchart [Thu, 20 Mar 2014 14:00:34 +0000 (15:00 +0100)]
sh_eth: Register MDIO bus before registering the network device

Network API functions that rely on the MDIO bus can be called as soon as
the driver calls register_netdev(). Register the MDIO bus before the
network device to avoid race conditions.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agosh_eth: Simplify MDIO bus initialization and release
Laurent Pinchart [Thu, 20 Mar 2014 14:00:33 +0000 (15:00 +0100)]
sh_eth: Simplify MDIO bus initialization and release

The network device passed to the sh_mdio_init and sh_mdio_release
functions is only used to access the sh_eth_private instance. Pass it
directly to those functions.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agosh_eth: Use the platform device as the MDIO bus parent
Laurent Pinchart [Thu, 20 Mar 2014 14:00:32 +0000 (15:00 +0100)]
sh_eth: Use the platform device as the MDIO bus parent

The MDIO bus parent is set to the network device. Beside not reflecting
the hardware topology, this prevents registering the MDIO bus before
initializing the network device. Fix it by setting the MDIO bus parent
to the platform device.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agosh_eth: Use the platform device for memory allocation
Laurent Pinchart [Thu, 20 Mar 2014 14:00:31 +0000 (15:00 +0100)]
sh_eth: Use the platform device for memory allocation

Memory allocated for the MDIO bus with the devm_kzalloc() API is
associated with the network device. While this will cause memory to be
freed at the right time, it doesn't allow allocating memory before the
network device is initialized.

Replace the network device with the parent platform device for memory
allocation to remove that dependency. This also improves consistency
with the other devm_* calls in the driver that all use the platform
device.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoieee802154: dgram: cleanup set of broadcast panid
Alexander Aring [Thu, 20 Mar 2014 13:57:03 +0000 (14:57 +0100)]
ieee802154: dgram: cleanup set of broadcast panid

This patch is only a cleanup to use the right define for a panid field.
The broadcast address and panid broadcast is still the same value.

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoaf_ieee802154: fix check on broadcast address
Alexander Aring [Thu, 20 Mar 2014 13:57:02 +0000 (14:57 +0100)]
af_ieee802154: fix check on broadcast address

This patch fixes an issue which was introduced by commit
b70ab2e87f17176d18f67ef331064441a032b5f3 ("ieee802154: enforce
consistent endianness in the 802.15.4 stack").

The correct behaviour should be a check on the broadcast address field
which is 0xffff.

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Jan Luebbe <jlu@pengutronix.de>
Cc: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoof_mdio: Allow the DT to specify the phy ID and avoid autoprobing
Jason Gunthorpe [Wed, 19 Mar 2014 22:15:24 +0000 (16:15 -0600)]
of_mdio: Allow the DT to specify the phy ID and avoid autoprobing

This makes the generic of_mdiobus_register parse the DT compatible string for
the pattern ethernet-phy-idAAAA.BBBB. If present it should be a value that
matches the phy-id register normally readable through MDIO.

When the ID is given the phy autoprobing is defeated and the phy is
created directly.

This is necessary to support phy's that cannot be autoprobed when
of_mdiobus_register is called. Specifically, my case has the phy in reset at
of_mdiobus_register, the reset is only released once the ethernet driver
starts, before it attaches to the phy.

Tested on ARM Kirkwood with phy id 0x01410e90 (Marvell 88E1318)

Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agodt: Document a compatible entry for MDIO ethernet Phys
Jason Gunthorpe [Wed, 19 Mar 2014 22:15:23 +0000 (16:15 -0600)]
dt: Document a compatible entry for MDIO ethernet Phys

This describes a compatible entry of the form:
  ethernet-phy-idAAAA,BBBB
Which is modelled after the PCI structured compatible entry
(pciVVVV,DDDD.SSSS.ssss.RR)

If present the OF core will be able to use this information to
directly create the correct phy without auto probing the bus.

Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoMerge branch 'cdc-next'
David S. Miller [Thu, 20 Mar 2014 20:58:01 +0000 (16:58 -0400)]
Merge branch 'cdc-next'

Ben Chan says:

====================
Adjust MTU as indicated by MBIM extended functional descriptor.

The MBIM extended functional descriptor, defined in "Universal Serial Bus
Communications Class Subclass Specification for Mobile Broadband Interface
Model, Revision 1.0, Errata-1" by USB-IF, indicates the operator preferred MTU
value via a wMTU field.

This patch set ensures that the initial MTU value set by cdc_ncm on a MBIM net
device does not exceed the wMTU value, provided the MBIM device exposes a MBIM
extended functional descriptor.

* Changelog
v2: Fixed a le16_to_cpu conversion issue in patch 2/2 pointed out by
    Bjørn Mork <bjorn@mork.no>
v3: No code changes. Resubmitted to include patch 1/2 as suggested by
    David Miller <davem@davemloft.net>
v4: No code changes. Resubmitted as suggested by David Miller:
    - Added a summary of the patch set
    - Carried the ACK from Greg Kroah-Hartman <gregkh@linuxfoundation.org>
    - Added a specified the tree (net-next) to apply the patch set to
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agonet: cdc_ncm: respect operator preferred MTU reported by MBIM
Ben Chan [Wed, 19 Mar 2014 21:00:06 +0000 (14:00 -0700)]
net: cdc_ncm: respect operator preferred MTU reported by MBIM

According to "Universal Serial Bus Communications Class Subclass
Specification for Mobile Broadband Interface Model, Revision 1.0,
Errata-1" published by USB-IF, the wMTU field of the MBIM extended
functional descriptor indicates the operator preferred MTU for IP data
streams.

This patch modifies cdc_ncm_setup to ensure that the MTU value set on
the usbnet device does not exceed the operator preferred MTU indicated
by wMTU if the MBIM device exposes a MBIM extended functional
descriptor.

Signed-off-by: Ben Chan <benchan@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoUSB: cdc: add MBIM extended functional descriptor structure
Ben Chan [Wed, 19 Mar 2014 21:00:05 +0000 (14:00 -0700)]
USB: cdc: add MBIM extended functional descriptor structure

This patch adds the MBIM extended functional descriptor structure
defined in "Universal Serial Bus Communications Class Subclass
Specification for Mobile Broadband Interface Model, Revision 1.0,
Errata-1" published by USB-IF.

Signed-off-by: Ben Chan <benchan@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoMerge branch 'mlx4-next'
David S. Miller [Thu, 20 Mar 2014 20:19:41 +0000 (16:19 -0400)]
Merge branch 'mlx4-next'

Or Gerlitz says:

====================
mlx4: Add support for single port VFs

The mlx4 Firmware && driver expose both ports of the device through one PCI function.

This can be non-optimal under virtualization schemes where the admin
would like the VF to expose one interface to the VM, etc.

This series from Matan Barak adds support for single ported VFs.

Since all the VF interaction with the firmware passes through the PF
 driver, we can emulate to the VF they have one port, and further create
a set of the VFs which act on port1 of the device and another set which
acts on port2.

Series done against net-next commit 3ab428a "netfilter: Add missing
vmalloc.h include to nft_hash.c"

Roland, we send this through netdev, but if you have comments, will love
to hear them.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agonet/mlx4: Adapt num_vfs/probed_vf params for single port VF
Matan Barak [Wed, 19 Mar 2014 16:11:53 +0000 (18:11 +0200)]
net/mlx4: Adapt num_vfs/probed_vf params for single port VF

A new syntax is added for the module parameters num_vfs and probe_vf.

  num_vfs=p1,p2,p1+p2
  probe_bf=p1,p2,p1+p2

Where p1(2) is the number of VFs on / probed VFs for physical
port1(2) and p1+p2 is the number of dual port VFs.

Single port VFs are currently supported only when the link type
for both ports of the device is Ethernet.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agonet/mlx4: Adapt code for N-Port VF
Matan Barak [Wed, 19 Mar 2014 16:11:52 +0000 (18:11 +0200)]
net/mlx4: Adapt code for N-Port VF

Adds support for N-Port VFs, this includes:
1. Adding support in the wrapped FW command
In wrapped commands, we need to verify and convert
the slave's port into the real physical port.
Furthermore, when sending the response back to the slave,
a reverse conversion should be made.
2. Adjusting sqpn for QP1 para-virtualization
The slave assumes that sqpn is used for QP1 communication.
If the slave is assigned to a port != (first port), we need
to adjust the sqpn that will direct its QP1 packets into the
correct endpoint.
3. Adjusting gid[5] to modify the port for raw ethernet
In B0 steering, gid[5] contains the port. It needs
to be adjusted into the physical port.
4. Adjusting number of ports in the query / ports caps in the FW commands
When a slave queries the hardware, it needs to view only
the physical ports it's assigned to.
5. Adjusting the sched_qp according to the port number
The QP port is encoded in the sched_qp, thus in modify_qp we need
to encode the correct port in sched_qp.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agonet/mlx4: Add utils for N-Port VFs
Matan Barak [Wed, 19 Mar 2014 16:11:51 +0000 (18:11 +0200)]
net/mlx4: Add utils for N-Port VFs

This patch adds the following utils:
1. Convert slave_id -> VF
2. Get the active ports by slave_id
3. Convert slave's port to real port
4. Get the slave's port from real port
5. Get all slaves that uses the i'th real port
6. Get all slaves that uses the i'th real port exclusively

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agonet/mlx4: Add data structures to support N-Ports per VF
Matan Barak [Wed, 19 Mar 2014 16:11:50 +0000 (18:11 +0200)]
net/mlx4: Add data structures to support N-Ports per VF

Adds the required data structures to support VFs with N (1 or 2)
ports instead of always using the number of physical ports.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoIB/mlx4_ib: Adapt code to use caps.num_ports instead of a constant
Matan Barak [Wed, 19 Mar 2014 16:11:49 +0000 (18:11 +0200)]
IB/mlx4_ib: Adapt code to use caps.num_ports instead of a constant

Some code in the mlx4 IB driver stack assumed MLX4_MAX_PORTS ports.

Instead, we should only loop until the number of actual ports in i
the device, which is stored in dev->caps.num_ports.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agosmsc911x: Change clock warning message to debug level
Fabio Estevam [Wed, 19 Mar 2014 14:22:06 +0000 (11:22 -0300)]
smsc911x: Change clock warning message to debug level

Since passing the clock is not mandatory, change the warning message to debug,
so that we avoid getting the following clock failure message on every boot:

smsc911x: Driver version 2008-10-21
smsc911x smsc911x (unregistered net_device): couldn't get clock -2
libphy: smsc911x-mdio: probed

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agonet: remove empty lines from tcp_syn_flood_action
Daniel Baluta [Wed, 19 Mar 2014 13:58:25 +0000 (15:58 +0200)]
net: remove empty lines from tcp_syn_flood_action

Signed-off-by: Daniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net...
David S. Miller [Thu, 20 Mar 2014 18:19:45 +0000 (14:19 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/jkirsher/net-next

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to e100, igb, igbvf, ixgbe and ixgbevf.

Stefan adds a igb patch to enable the ability strip VLAN header information
for packets bound for a VM on i350 hardware.

Joe Perches provides patches for e100, igb, igbvf, ixgbe and ixgbevf to
convert the use of __constant_<foo> to just <foo> to align with the rest
of the kernel.

Don provides two fixes for ixgbe, first resolves a link issue with DA
cables where we were not always freeing the firmware/software semaphore
after grabbing it.  Second stops caching whether the management firmware
was enabled, however since this is not static, we really need to verify
with each check.

Jacob provides six fixes/cleanups for ixgbe, most notably, correct
the stop_mac_link_on d3() to check the Core Clock Disable bit before
stopping link and to fully check to see if manage firmware is running or
could be enabled before bringing down the link.  Fix flow control
auto-negation for KR/KX/K4 interfaces, since setting up MAC link, the
cached autoc value and current autoc value were being incorrectly used to
determine whether link reset is required.

Emil provides a fix for ixgbe where there was a chance for aggressive
start_ndo_zmit() callers to sneak packets between enabling the Tx queues
and the link coming up.  To resolve this, move the call to enable Tx
queues to after the link is established.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoixgbe: enable tx queues after link up
Emil Tantilov [Thu, 20 Mar 2014 03:47:53 +0000 (03:47 +0000)]
ixgbe: enable tx queues after link up

This patch moves the call to enable Tx queues after the link is established.
Previously there was a chance for aggressive start_ndo_xmit() callers to
sneak packets between enabling the Tx queues and the link coming up.

In addition it replaces netif_tx_start_all_queues() with
netif_tx_wake_all_queues() to allow for flushing of the qdisc.

CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoixgbe: Stop cacheing if the MNG FW enabled
Don Skidmore [Thu, 27 Feb 2014 09:03:30 +0000 (09:03 +0000)]
ixgbe: Stop cacheing if the MNG FW enabled

We use to cache whether the MNG FW was enabled, how since this isn't
static we really need to verify with each check.  This patch makes that
change.

CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoixgbe: clean up ixgbe_atr_compute_perfect_hash_82599
Jacob Keller [Sat, 22 Feb 2014 01:23:59 +0000 (01:23 +0000)]
ixgbe: clean up ixgbe_atr_compute_perfect_hash_82599

Rather than assign several parameters in a row, we should use a for
loop, which reduces code size.

CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoixgbe: use ixgbe_read_pci_cfg_word
Jacob Keller [Sat, 22 Feb 2014 01:23:58 +0000 (01:23 +0000)]
ixgbe: use ixgbe_read_pci_cfg_word

This patch replaces some direct uses of pci_read_config_word with the
protected ixgbe_read_pci_cfg_word function, which checks for whether the
adapter is removed when LER is enabled. We shouldn't use the
pci_read_config_word calls directly because of these checks.

This patch also cleans up an unnecessary save of a pointer to the mac
object, as our standard style is to just use the hw pointer.

CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoixgbe: remove unused media type
Jacob Keller [Sat, 22 Feb 2014 01:23:57 +0000 (01:23 +0000)]
ixgbe: remove unused media type

This patch reverts the addition of the fiber_fixed type, which ended up
never being used. We don't have plans to support this type going
forward, and there is no reason to keep an unused type around polluting
the code.

Reverts: 4e8e1bca6e2 ("ixgbe: add new media type")
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoixgbe: fix ixgbe_setup_mac_link_82599 autoc variables
Jacob Keller [Sat, 22 Feb 2014 01:23:56 +0000 (01:23 +0000)]
ixgbe: fix ixgbe_setup_mac_link_82599 autoc variables

This patch fixes flow control autonegotiation for KR/KX/K4 interfaces.
When setting up MAC link, the cached autoc value and current autoc value
were being incorrectly used to determine whether link reset is required.
This resulted in the driver ignoring and discarding flow control
negotiation changes that occur since the caching happened, as well as
when the mac was being setup.

This patch also splits the assignments for the 3 autoc variables into
their own block, and adds a comment explaining what each one means, in
order to help keep logic more straightforward while reading the code.

CC: Arun Sharma <asharma@fb.com>
Reported-by: Sourav Chatterjee <sourav.chatterjee@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoixgbe: fix ixgbe_stop_mac_link_on_d3_82599 to check mng correctly
Jacob Keller [Sat, 22 Feb 2014 01:23:55 +0000 (01:23 +0000)]
ixgbe: fix ixgbe_stop_mac_link_on_d3_82599 to check mng correctly

Previously, we did a full check to see if MNG FW was running. Instead,
we should only check to see whether it could be enabled. Since it may
become active while down, we don't want to bring the link down.

CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoixgbe: check Core Clock Disable bit
Jacob Keller [Sat, 22 Feb 2014 01:23:54 +0000 (01:23 +0000)]
ixgbe: check Core Clock Disable bit

This patch corrects the stop_mac_link_on_d3 function in ixgbe_82599 by
checking the Core Clock Disable bit before stopping link.

CC: Arun Sharma <asharma@fb.com>
Reported-by: Chris Pavlas <chris.pavlas@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoixgbe: fix errors related to protected AUTOC calls
Don Skidmore [Wed, 19 Mar 2014 09:16:26 +0000 (09:16 +0000)]
ixgbe: fix errors related to protected AUTOC calls

Found several incorrect conditionals after calling the prot_autoc_*
functions. Likewise we weren't always freeing the FWSW semaphore after
grabbing it.   This would lead to DA cables being unable to link along with
possible other errors.

CC: Arun Sharma <asharma@fb.com>
CC: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoixgbevf: Convert uses of __constant_<foo> to <foo>
Joe Perches [Thu, 13 Mar 2014 05:19:30 +0000 (05:19 +0000)]
ixgbevf: Convert uses of __constant_<foo> to <foo>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.

Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoixgbe: Convert uses of __constant_<foo> to <foo>
Joe Perches [Thu, 13 Mar 2014 05:19:25 +0000 (05:19 +0000)]
ixgbe: Convert uses of __constant_<foo> to <foo>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.

Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoigbvf: Convert uses of __constant_<foo> to <foo>
Joe Perches [Thu, 13 Mar 2014 05:19:19 +0000 (05:19 +0000)]
igbvf: Convert uses of __constant_<foo> to <foo>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.

Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoigb: Convert uses of __constant_<foo> to <foo>
Joe Perches [Thu, 13 Mar 2014 05:19:14 +0000 (05:19 +0000)]
igb: Convert uses of __constant_<foo> to <foo>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.

Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoe100: Convert uses of __constant_<foo> to <foo>
Joe Perches [Thu, 13 Mar 2014 05:19:09 +0000 (05:19 +0000)]
e100: Convert uses of __constant_<foo> to <foo>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.

Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoigb: enable VLAN stripping for VMs with i350
Stefan Assmann [Wed, 11 Dec 2013 22:10:12 +0000 (22:10 +0000)]
igb: enable VLAN stripping for VMs with i350

For i350 VLAN stripping for VMs is not enabled in the VMOLR register but in
the DVMOLR register. Making the changes accordingly. It's not necessary to
unset the E1000_VMOLR_STRVLAN bit on i350 as the hardware will simply ignore
it.

Without this change if a VLAN is configured for a VF assigned to a guest
via (i.e.)
ip link set p1p1 vf 0 vlan 10
the VLAN tag will not be stripped from packets going into the VM. Which they
should be because the VM itself is not aware of the VLAN at all.

Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoqeth: Fix IP version detection for VLAN traffic
Stefan Raspl [Wed, 19 Mar 2014 06:58:02 +0000 (07:58 +0100)]
qeth: Fix IP version detection for VLAN traffic

The current code would always return 0 for VLAN-encapsulated IP traffic.
One notable side effect was that VLAN traffic would never get prioritized
on OSD and OSX devices when priority queueing modes prio_queueing_tos or
prio_queueing_prec were enabled.

Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoqeth: Removed unused parameter
Stefan Raspl [Wed, 19 Mar 2014 06:58:01 +0000 (07:58 +0100)]
qeth: Removed unused parameter

Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoqeth: make qeth_query_card_info_cb() static
Heiko Carstens [Wed, 19 Mar 2014 06:58:00 +0000 (07:58 +0100)]
qeth: make qeth_query_card_info_cb() static

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoaf_iucv: recvmsg problem for SOCK_STREAM sockets
Ursula Braun [Wed, 19 Mar 2014 06:57:59 +0000 (07:57 +0100)]
af_iucv: recvmsg problem for SOCK_STREAM sockets

Commit f9c41a62bba3f3f7ef3541b2a025e3371bcbba97 introduced
a problem for SOCK_STREAM sockets, when only part of the
incoming iucv message is received by user space. In this
case the remaining data of the iucv message is lost.
This patch makes sure an incompletely received iucv message
is queued back to the receive queue.

Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reported-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net...
David S. Miller [Thu, 20 Mar 2014 03:55:48 +0000 (23:55 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/jkirsher/net-next

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to i40e, i40evf, e1000e, ixgbe and ixgbevf.

Mitch adds support for the VF link state ndo which allows the PF driver
to control the virtual link state of the VF devices.  Added
support for viewing and modifying RSS hash options and RSS hash look-up
table programming through ethtool for i40evf.  Fixed complaint about
the use of min() where min_t() should be used in i40evf.

Anjali adds support for ethtool -k option for NTUPLE control for i40e.

Elizabeth cleans up and refactors i40e_open() to separate out the VSI
code into its own i40e_vsi_open().

Jesse enables the hardware feature head write back to avoid updating the
descriptor ring by marking each descriptor with a DD bit and instead
writes a memory location with an update to where the driver should clean
up to in i40e and i40evf.  Reduces context descriptors for i40e/i40evf
since we do not need context descriptors for every packet, only for
TSO or timesync.

Dan Carpenter fixes a potential array underflow in i40e_vc_process_vf_msg().

Dave fixes an e1000e hardware unit hang where the check for pending Tx work
when link is lost was mistakenly moved to be done only when link is first
detected to be lost.  Fixed a problem with poor network performance on
certain silicon in e1000e when configured for 100M HDX performance.

Carolyn adds register defines needed for time sync functions and the code
to call the updated defines.

Jacob adds the ixgbe function for writing PCI config word and checks
whether the adapter has been removed first.

Mark adds the bit __IXGBEVF_REMOVING to indicate that the module is being
removed because the __IXGBEVF_DOWN bit had been overloaded for this
purpose, but leads to trouble.  ixgbevf_down function can now prevent
multiple executions by doing test_and_set_bit on __IXGBEVF_DOWN.

v2:
- dropped patch Mitch's patch "i40evf: Support RSS option in ethtool"
  based on feedback from Ben Hutchings so that Mitch can re-work the
  patch solution

v3:
- removed unnecessary parenthesis in patch 1 based on feedback from David
  Miller
- changed a macro to get the next queue to a function in patch 2 based on
  feedback from David Miller
- added blank lines after variable declaration and code in two functions
  in patch 6 based on feedback from David Miller
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoixgbevf: Protect ixgbevf_down with __IXGBEVF_DOWN bit
Mark Rustad [Tue, 4 Mar 2014 03:02:18 +0000 (03:02 +0000)]
ixgbevf: Protect ixgbevf_down with __IXGBEVF_DOWN bit

The ixgbevf_down function can now prevent multiple executions by
doing test_and_set_bit on __IXGBEVF_DOWN. This did not work before
introduction of the __IXGBEVF_REMOVING bit, because of overloading
of __IXGBEVF_DOWN. Also add smp_mb__before_clear_bit call before
clearing the __IXGBEVF_DOWN bit.

Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoixgbevf: Indicate removal state explicitly
Mark Rustad [Tue, 4 Mar 2014 03:02:13 +0000 (03:02 +0000)]
ixgbevf: Indicate removal state explicitly

Add a bit, __IXGBEVF_REMOVING, to indicate that the module is being
removed. The __IXGBEVF_DOWN bit had been overloaded for this purpose,
but that leads to trouble. A few places now check both __IXGBEVF_DOWN
and __IXGBEVF_REMOVING.

Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoixgbe: add ixgbe_write_pci_cfg_word with ixgbe_removed check
Jacob Keller [Sat, 22 Feb 2014 01:23:53 +0000 (01:23 +0000)]
ixgbe: add ixgbe_write_pci_cfg_word with ixgbe_removed check

Inline with the current use for ixgbe_read_pci_cfg_word, create a
similar function for writing PCI config, which checks whether the
adapter has been removed first, if Live Error Recovery has been enabled.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoigb: Add register defines needed for time sync functions
Carolyn Wyborny [Tue, 11 Mar 2014 06:15:37 +0000 (06:15 +0000)]
igb: Add register defines needed for time sync functions

This patch adds defines needed for implementing the auxiliary time sync
functions and also changes code to call the updated defines instead of
the old.

Reported-by: Richard Cochran <ricahrdcochran@gmail.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoe1000e: Fix Explicitly set Transmit Control Register
David Ertman [Mon, 13 Jan 2014 23:19:27 +0000 (23:19 +0000)]
e1000e: Fix Explicitly set Transmit Control Register

This patch causes the TCTL to be explicitly set to fix a problem with
poor network performance (throughput) on certain silicon when configured
for 100M HDX performance.

Cc: Todd Fujinaka <todd.fujinaka@intel.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce W. Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoe1000e: Fix Hardware Unit Hang
David Ertman [Wed, 8 Jan 2014 01:07:55 +0000 (01:07 +0000)]
e1000e: Fix Hardware Unit Hang

The check for pending Tx work when link is lost was mistakenly moved to be
done only when link is first detected to be lost.  It turns out there is a
small window of opportunity for additional Tx work to get queued up shortly
after link is dropped.

Move the check back to the place it was before in the watchdog task.  Put in
additional debug information for other reset paths and a final catch-all for
false hangs in the scheduled function that prints out the hardware hang
message.

Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoi40e/i40evf: Bump build versions
Catherine Sullivan [Fri, 14 Feb 2014 02:14:42 +0000 (02:14 +0000)]
i40e/i40evf: Bump build versions

Bump to version 0.3.36 for i40e and 0.9.16 for i40evf.

Change-ID: I7b4ff97b32d2825181803c03c316381a7608a618
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoi40e: potential array underflow in i40e_vc_process_vf_msg()
Dan Carpenter [Wed, 15 Jan 2014 06:43:39 +0000 (06:43 +0000)]
i40e: potential array underflow in i40e_vc_process_vf_msg()

If "vf_id" is smaller than hw->func_caps.vf_base_id then it leads to
an array underflow of the pf->vf[] array.  This is unlikely to happen
unless the hardware is bad, but it's a small change and it silences a
static checker warning.

Fixes: 7efa84b7abc1 ('i40e: support VFs on PFs other than 0')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoi40e/i40evf: reduce context descriptors
Jesse Brandeburg [Fri, 14 Feb 2014 02:14:41 +0000 (02:14 +0000)]
i40e/i40evf: reduce context descriptors

We don't need context descriptors for every packet, only tso
or timesync.  This fixes a bug in the driver where it would
always add a context even if all the passed in values
to the context descriptor function were 0/default values.

Change-ID: I0101d2b893380707b5c2de61aab3e16d4310e9a1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoi40e/i40evf: enable hardware feature head write back
Jesse Brandeburg [Fri, 14 Feb 2014 02:14:40 +0000 (02:14 +0000)]
i40e/i40evf: enable hardware feature head write back

The hardware supports a feature to avoid updating the descriptor
ring by marking each descriptor with a DD bit, and instead
writes a memory location with an update to where the driver
should clean up to.  Enable this feature.

Change-ID: I5da4e0681f0b581a6401c950a81808792267fe57
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoi40e: Refactor and cleanup i40e_open(), adding i40e_vsi_open()
Elizabeth Kappler [Sat, 15 Feb 2014 07:41:38 +0000 (07:41 +0000)]
i40e: Refactor and cleanup i40e_open(), adding i40e_vsi_open()

This patch cleans up and moves a portion of i40e_open to i40e_vsi_open,
in order to have a shorter vsi_open function that does only that.

Change-ID: I1c418dda94dcfc0eb7d4386a70c330692ef5ecc9
Signed-off-by: Elizabeth Kappler <elizabeth.m.kappler@intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoi40e: Patch to enable Ethtool/netdev feature flag for NTUPLE control
Anjali Singhai Jain [Fri, 14 Feb 2014 02:14:38 +0000 (02:14 +0000)]
i40e: Patch to enable Ethtool/netdev feature flag for NTUPLE control

This enables option '-k/-K' in ethtool for NTUPLE control.
NTUPLE control requires a reset, to take effect. When the feature is
turned off, the SW list of stored FD SB filters gets cleaned up.

Change-ID: I9d564b67a10d4afa11de3b320d601c3d2e6edc1f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoi40evf: use min_t
Mitch Williams [Tue, 11 Feb 2014 08:27:52 +0000 (08:27 +0000)]
i40evf: use min_t

Checkpatch complained in an earlier patch about using min(), but that
change would have been completely unrelated to the point of that patch.
So fix it here.

Change-ID: I2cd87b39cfd406850d283b88f259757a6bcd14cd
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agoi40evf: correctly program RSS HLUT table
Mitch Williams [Tue, 11 Feb 2014 08:27:50 +0000 (08:27 +0000)]
i40evf: correctly program RSS HLUT table

The HLUT programming loop in in i40evf_configure_rss was a) overly-
complicated, and b) just plain broken. Most of the entries ended up being
not written at all, so most of the flows ended up at queue zero.

Refactor the HLUT programming loop to simply walk through the registers
and write four values to each one, incrementing through the number of
available queues.

Change-ID: I75766179bc67e4e997187794f3144e28c83fd00d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agomicrel: fix masking off LED bits
Sergei Shtylyov [Tue, 18 Mar 2014 23:58:16 +0000 (02:58 +0300)]
micrel: fix masking off LED bits

Commit 20d8435a1cff (phy: micrel: add of configuration for LED mode) made the
obvious mistake when masking off  the LED mode bits: forgot to do a logical NOT
to the mask with which it ANDs the register value, so that unrelated bits are
cleared instead.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoi40e: support VF link state ndo
Mitch Williams [Tue, 11 Feb 2014 08:27:49 +0000 (08:27 +0000)]
i40e: support VF link state ndo

This netdev op allows the PF driver to control the virtual link state of
the VF devices. This can be used to deny naughty VF drivers access to
the wire, or to allow VFs (regardless of temperament) to communicate
with each other over the device's internal switch even though external
link is down.

Add the actual ndo function, and modify vc_notify_link_state to check
the link status of each VF before sending a message in the case when
physical link changes state.

Change-ID: Ib5a6924da78c540789f21d26b5e8086d71c29384
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10 years agonetfilter: Add missing vmalloc.h include to nft_hash.c
David S. Miller [Wed, 19 Mar 2014 03:12:02 +0000 (23:12 -0400)]
netfilter: Add missing vmalloc.h include to nft_hash.c

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoieee802154: properly unshare skbs in ieee802154 *_rcv functions
Phoebe Buckheister [Mon, 17 Mar 2014 17:30:19 +0000 (18:30 +0100)]
ieee802154: properly unshare skbs in ieee802154 *_rcv functions

ieee802154 sockets do not properly unshare received skbs, which leads to
panics (at least) when they are used in conjunction with 6lowpan, so
run skb_share_check on received skbs.
6lowpan also contains a use-after-free, which is trivially fixed by
replacing the inlined skb_share_check with the explicit call.

Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Tested-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agoMerge tag 'linux-can-next-for-3.15-20140317' of git://gitorious.org/linux-can/linux...
David S. Miller [Tue, 18 Mar 2014 19:20:00 +0000 (15:20 -0400)]
Merge tag 'linux-can-next-for-3.15-20140317' of git://gitorious.org/linux-can/linux-can-next

linux-can-next-for-3.15-20140317

Marc Kleine-Budde says:

====================
this is a pull request of three patches for net-next/master.

It consists of a patch by Oliver Hartkopp, which unifies the MTU
settings for CAN interfaces. A patch by Christopher R. Baker populates
netdev::dev_id for udev discrimination for multi interface CAN devices.
Alexander Shiyan contributes a patch for the mcp251x driver which fixes
the regulators operation if CONFIG_REGULATOR is not enabled.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agovia: fix a punctuation typo
wangweidong [Mon, 17 Mar 2014 07:52:17 +0000 (15:52 +0800)]
via: fix a punctuation typo

In generic, after an assignment, we use ';' instead of ','.
Although, it won't hurt.

Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agodoc: update driver TX algorithm in timestamping.txt
Jakub Kicinski [Sun, 16 Mar 2014 19:32:48 +0000 (20:32 +0100)]
doc: update driver TX algorithm in timestamping.txt

Since cd4d8fdad1f1 ("net: kernel panic in dev_hard_start_xmit:
remove faulty software TX time stamping") dev_hard_start_xmit()
will not provide software timestamps. It's a responsibility of
the drivers to call skb_tx_timestamp() at the right time.

Cc: linux-doc@vger.kernel.org
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 years agobonding: ratelimit pr_warn()s in 802.3ad mode
Veaceslav Falico [Sun, 16 Mar 2014 16:55:03 +0000 (17:55 +0100)]
bonding: ratelimit pr_warn()s in 802.3ad mode

Only ratelimit the ones that might spam, omiting the ones from
enslave/deslave.

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>