[media] s5p-csis: Add support for non-image data packets capture

MIPI-CSI has internal memory mapped buffers for the frame embedded
(non-image) data. There are two buffers, for even and odd frames which
need to be saved after an interrupt is raised. The packet data buffers
size is 4 KiB and there is no status register in the hardware where the
actual non-image data size can be read from. Hence the driver copies
whole packet data buffer into a buffer provided by the FIMC driver.
This will form a separate plane in the user buffer.
When FIMC DMA engine is stopped by the driver due the to user space
not keeping up with buffer de-queuing the MIPI-CSIS will still run,
however it must discard data which is not captured by FIMC. Which
frames are actually capture by MIPI-CSIS is determined by means of
the s_tx_buffer subdev callback. When it is not called after a single
embedded data frame has been captured and copied and before next
embedded data frame interrupt occurrs, subsequent embedded data frames
will be dropped.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add V4L2_PIX_FMT_S5C_UYVY_JPG fourcc definition

This patch adds definition of the Samsung S5C73M3 camera specific
image format. V4L2_PIX_FMT_S5C_UYVY_JPG is a two-planar format,
the  first plane contains interleaved UYVY and JPEG data followed
by meta-data. The second plane contains additional meta-data needed
for extracting JPEG and UYVY data stream from the first plane.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add V4L2_MBUS_FMT_S5C_UYVY_JPEG_1X8 media bus format

This patch adds media bus pixel code for the interleaved JPEG/UYVY
image format used by S5C73MX Samsung cameras. This interleaved image
data is transferred on MIPI-CSI2 bus as User Defined Byte-based Data.
It also defines an experimental vendor and device specific media bus
formats section and adds related DocBook documentation.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add [get/set]_frame_desc subdev callbacks

Add subdev callbacks for setting up parameters of the frame on media bus
that are not exposed to user space directly. This is just an initial,
mostly stub implementation. struct v4l2_mbus_frame_desc is intended
to be extended with sub-structures specific to a particular hardware media
bus. For now these new callbacks are used only to query or specify maximum
size of a compressed or hybrid (container) media bus frame in octets.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add s_rx_buffer subdev video operation

The s_rx_buffer callback allows the host to set buffer for a data being
received by the subdev, e.g. non-image frame (meta) data. This callback
can be implemented by subdevice like a MIPI CSI2 receiver, allowing the
host driver to gather additional data into frame buffer passed to user
space.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: fix compiler warning

drivers/media/platform/s5p-fimc/fimc-m2m.c:561:2: warning: passing argument 2 of 'fimc_m2m_try_crop' discards 'const' qualifier from pointer target type [enabled by default]
drivers/media/platform/s5p-fimc/fimc-m2m.c:502:12: note: expected 'struct v4l2_crop *' but argument is of type 'const struct v4l2_crop *'
This is fall-out from this commit:
commit 4f996594ceaf6c3f9bc42b40c40b0f7f87b79c86
Author: Hans Verkuil <hans.verkuil@cisco.com>
    [media] v4l2: make vidioc_s_crop const

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-g2d: fix compiler warning

drivers/media/platform/s5p-g2d/g2d.c:535:2: warning: passing argument 3 of 'vidioc_try_crop' discards 'const' qualifier from pointer target type [enabled by default]
drivers/media/platform/s5p-g2d/g2d.c:510:12: note: expected 'struct v4l2_crop *' but argument is of type 'const struct v4l2_crop *'
This is fall-out from this commit:
commit 4f996594ceaf6c3f9bc42b40c40b0f7f87b79c86
Author: Hans Verkuil <hans.verkuil@cisco.com>
    [media] v4l2: make vidioc_s_crop const

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-jpeg: use clk_prepare_enable and clk_disable_unprepare

Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.

Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] technisat-usb2: add a MODULE_DEVICE_TABLE for udev autoload

This patch adds a module-device-table-entry to the
technisat-usb2-driver which will help udev to on-demand load the
driver. This was obviously forgotten during initial commit.

Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] davinci: vpbe: replace V4L2_OUT_CAP_CUSTOM_TIMINGS with V4L2_OUT_CAP_DV_TIMINGS

This patch replaces V4L2_OUT_CAP_CUSTOM_TIMINGS macro with
V4L2_OUT_CAP_DV_TIMINGS. As V4L2_OUT_CAP_CUSTOM_TIMINGS is being phased
out.

Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: davinci: vpbe: fix build warning

recent patch with commit id 4f996594ceaf6c3f9bc42b40c40b0f7f87b79c86
which makes vidioc_s_crop const, was causing a following build warning,
vpbe_display.c: In function 'vpbe_display_s_crop':
vpbe_display.c:640: warning: initialization discards qualifiers from pointer target type
This patch fixes the above build warning.

Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ths7303: enable THS7303 for HD modes

add filter settings for high def modes like 1080i,
1080p,720p and others and implementing dv_timings.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dm644x: replace the obsolete preset API by the timings API

This patch replaces the preset API by the timings API, and
appropriate changes in board file.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] af9033: prevent unintended underflow

As spotted by Dan Carpenter <dan.carpenter@oracle.com> (thanks!), we have
improperly used an unsigned variable in a calculation that may result in a
negative number. This may cause an unintended underflow if the interface
frequency of the tuner is > approx. 40MHz.
This patch should resolve the issue, following an approach similar to what is
used in af9013.c.

[crope@iki.fi: add Reported-by]
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: davinci: vpfe: fix build error

recent patch with commit id 4f996594ceaf6c3f9bc42b40c40b0f7f87b79c86
which makes vidioc_s_crop const, was causing a following build error.
vpfe_capture.c: In function 'vpfe_s_crop':
vpfe_capture.c:1695: error: assignment of read-only location '*crop'
vpfe_capture.c:1706: warning: passing argument 1 of
'ccdc_dev->hw_ops.set_image_window' discards qualifiers from pointer target type
vpfe_capture.c:1706: note: expected 'struct v4l2_rect *' but argument is of
type 'const struct v4l2_rect *'
make[4]: *** [drivers/media/platform/davinci/vpfe_capture.o] Error 1

Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

em28xx: regression fix: use DRX-K sync firmware requests on em28xx

As em28xx-dvb will always be initialized asynchronously, there's
no need anymore for a separate thread to load the DRX-K firmware.

Fixes a known regression with kernel 3.6 with tda18271 driver
and asynchronous DRX-K firmware load.

Antti tested it with the following hardware:
        Hauppauge WinTV HVR 930C
        MaxMedia UB425-TC
        PCTV QuatroStick nano (520e)

Tested-by: Antti Palosaari <crope@iki.fi>
Cc: stable@kernel.org # for Kernel 3.6 - please note that driver location has changed
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

drxk: allow loading firmware synchrousnously

Due to udev-182, the firmware load was changed to be async, as
otherwise udev would give up of loading a firmware.

Add an option to return to the previous behaviour, async firmware
loads cause failures with the tda18271 driver.

Antti tested it with the following hardware:
        Hauppauge WinTV HVR 930C
        MaxMedia UB425-TC
        PCTV QuatroStick nano (520e)

Tested-by: Antti Palosaari <crope@iki.fi>
Cc: stable@kernel.org # for Kernel 3.6 - please note that driver location has changed
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

em28xx: Make all em28xx extensions to be initialized asynchronously

em28xx-dvb, em28xx-alsa and em28xx-ir are typically initialized
asyncrhronously. The exception for it is when those modules
are loaded before em28xx (or before an em28xx card insertion) or
when they're built in.

Make the extentions to always load asynchronously. That allows
having all DVB firmwares loaded synchronously with udev-182.

Antti tested it with the following hardware:
Hauppauge WinTV HVR 930C
MaxMedia UB425-TC
PCTV QuatroStick nano (520e)

Tested-by: Antti Palosaari <crope@iki.fi>
Cc: stable@kernel.org # for Kernel 3.6 - please note that driver location has changed
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tda18271: properly report read errors in tda18271_get_id

Until now, if there is a read error in tda18271_get_id, the driver
reports "Unknown device..."  Instead, check the return value of
tda18271_read_regs and display the appropriate error message.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tda18271: delay IR & RF calibration until init() if delay_cal is set

if the configuration option 'delay_cal' is set, delay both IR & RF
calibration until init() is called.
both module option 'cal' or configuration option 'rf_cal_on_startup'
will override this delay. it makes no sense to mix 'delay_cal' with
'rf_cal_on_startup' as these options conflict with each other.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] MAINTAINERS: add Michael Krufky as tda827x maintainer

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] MAINTAINERS: add Michael Krufky as tda8290 maintainer

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] MAINTAINERS: add Michael Krufky as cxusb maintainer

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] MAINTAINERS: add Michael Krufky as lg2160 maintainer

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] MAINTAINERS: add Michael Krufky as lgdt3305 maintainer

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] MAINTAINERS: add Michael Krufky as mxl111sf maintainer

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] MAINTAINERS: add Michael Krufky as mxl5007t maintainer

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] MAINTAINERS: add Michael Krufky as tda18271 maintainer

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-tv: Report only multi-plane capabilities in vidioc_querycap

The mixer video node supports only multi-planar API so the driver
should not be setting V4L2_CAP_VIDEO_OUTPUT flags. Fix this and
also switch to device_caps. Additionally fix the VIDIOC_ENUM_FMT
ioctl handler which now works for V4L2_BUF_TYPE_CAPTURE, rather
than expected V4L2_BUF_TYPE_CAPTURE_MPLANE.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-mfc: Fix misplaced return statement in s5p_mfc_suspend()

return statement was wrongly placed before a code that needs to be
executed. Moved the return statement to the end of the function.
Tested suspend/resume on SMDK4412 board using 3.5-rc6 kernel.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] exynos-gsc: Add missing static storage class specifiers

Fixes the following warnings:
drivers/media/platform/exynos-gsc/gsc-core.c:313:5: warning:
symbol 'get_plane_info' was not declared. Should it be static?
drivers/media/platform/exynos-gsc/gsc-core.c:746:28: warning:
symbol 'gsc_ctrl_ops' was not declared. Should it be static?
drivers/media/platform/exynos-gsc/gsc-m2m.c:102:5: warning:
symbol 'gsc_fill_addr' was not declared. Should it be static?
drivers/media/platform/exynos-gsc/gsc-m2m.c:252:16: warning:
symbol 'gsc_m2m_qops' was not declared. Should it be static?

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] exynos-gsc: Remove <linux/version.h> header file inclusion

version.h is not needed for these files.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Fix incorrect condition in fimc_lite_reqbufs()

Fixes a typo in a conditional evaluation.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-tv: Fix potential NULL pointer dereference error

When mdev is NULL, the error print statement will try to dereference
the NULL pointer.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5k6aa: Fix possible NULL pointer dereference

Make sure __s5k6aa_get_crop_rect() always returns valid pointer,
as it is assumed at the callers.
crop->which is already validated when subdev set_crop and get_crop
callbacks are called from within the v4l2-core. If it ever happens
the crop operations are called directly for some reason in kernel
space, with incorrect crop->which argument, just log it with WARN
and return reference to the TRY crop.

Reported-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-mfc: optimized code related to working contextes

All code setting/clearing working context bits has been moved
to separate functions. set_bit/clear_bit have been replaced by
non-atomic variants - variable is already guarded by spin_lock.

Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-mfc: added support for end of stream handling in MFC encoder

s5p-mfc encoder after receiving V4L2_ENC_CMD_STOP command
will instruct MFC device to release all encoded frames.
After dequeuing last encoded frame driver will generate
V4L2_EVENT_EOS event.

Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Protect driver data with a mutex

Without the locking the driver's data could get corrupted when the subdev
is accessed from user space and from host driver by multiple processes.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Remove unneeded control ops assignments

Since all host drivers using this subdev are already using
the control framework these compatibility ops can be removed.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Keep local copy of sensors platform data

Use a copy of sensor platform data structure, rather than referencing
external platform data from the driver. This allows to fill the local
copy with values parsed from device tree when needed.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-csis: Add transmission errors logging

Add hardware event/error counters which can be dumped into the kernel
log through VIDIOC_LOG_STATUS ioctl. The counters are reset  in each
s_stream(1) call. Any errors are logged after streaming is turned off.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-mfc: Add missing braces around sizeof

Silences the following warnings:
WARNING: sizeof *ctx should be sizeof(*ctx)
WARNING: sizeof *dev should be sizeof(*dev)

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Add missing braces around sizeof

Silences the following warning:
WARNING: sizeof *ctx should be sizeof(*ctx)

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Replace asm/* headers with linux/*

Silences the following warning:
WARNING: Use #include <linux/sizes.h> instead of <asm/sizes.h>

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Add pipeline ops to separate FIMC-LITE module

In order to reuse the FIMC-LITE module on Exynos4 and Exynos5
SoC introduce a set of callbacks for the media pipeline control
from within FIMC/FIMC-LITE video node. It lets us avoid symbol
dependencies between FIMC-LITE and the whole media device driver,
which simplifies the initialization sequences and doesn't
introduce issues preventing common kernel image for exynos4 and
exynos5 SoCs.
This patch also corrects following build errors:
drivers/built-in.o: In function `buffer_queue':
drivers/media/video/s5p-fimc/fimc-lite.c:414: undefined reference
to `fimc_pipeline_s_stream'
drivers/built-in.o: In function `fimc_lite_resume':
drivers/media/video/s5p-fimc/fimc-lite.c:1518: undefined reference
to `fimc_pipeline_initialize'
drivers/built-in.o: In function `fimc_lite_suspend':
drivers/media/video/s5p-fimc/fimc-lite.c:1544: undefined reference
to `fimc_pipeline_shutdown'
when only CONFIG_VIDEO_EXYNOS_FIMC_LITE is selected, without
CONFIG_VIDEO_S5P_FIMC.

Reported-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-jpeg: Add missing braces around sizeof

Silences the following warning:
WARNING: sizeof *ctx should be sizeof(*ctx)

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: fimc-lite: Propagate frame format on the subdev

When setting image format on subdev's sink pad there was no
propagation to the source pad. This resulted in wrong reported
format on the source pad and wrong device configuration when
used from subdev interace level only. Correct this by propagating
format from the sink to the source pad.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: fimc-lite: Correct Bayer pixel format definitions

Replace erroneous V4L2_PIX_FMT_* entries with their V4L2_MBUS_FMT_*
counterparts. This enables use of raw Bayer formats on FIMC-LITE.?
subdevs.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tda18271: make 'low-power standby mode after attach' multi-instance safe

Ensure that unnecessary features are powered down at the end of the
attach() function on attach of the tuner's first instance. If the
configuration requires the loop thru or xtout features, they will
remain enabled.
This must *only* be done after attaching the first instance of the tuner.
If there are multiple instances of the tuner, the bridge driver will need
to maintain power managament by itself.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tda18271: enter low-power standby mode at the end of tda18271_attach()

Ensure that unnecessary features are powered down at the end of the
attach() function.  If the configuration requires the loop thru or
xtout features, they will remain enabled.
Thanks to Antti Palosaari for noticing the additional power consumption.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ivtv: fix format enumeration: don't show invalid formats

Depending on the device node only the compressed or the uncompressed format
should be shown, not both.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ivtv: disable a bunch of ioctls that are invalid for the decoder VBI

The VBI capture for the decoder (/dev/vbi8) is special in that it captures
the VBI stream embedded in an MPEG stream that is being decoded.
A lot of the ioctls that would normally be valid have to be disabled since
they make no sense for such a device, and v4l2-compliance will complain
about that.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ivtv: fix incorrect service_set for the decoder VBI capture

Found with v4l2-compliance.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ivtv: don't allow g/s_frequency for output device nodes

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ivtv: fix v4l2-compliance errors for the radio device

- fix error code when attempting to read from write-only streams.
- fix error code when attempting to write to read-only streams.
- don't start capturing when polling on a radio node.
- give the radio node its own file operations struct.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ivtv: fix v4l2-compliance error: inconsistent std reporting

The tuner input has a different standard mask than a S-Video or Composite input.
Changing the standard should change tvnorms as well for all device nodes.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ivtv: DECODER_CMD v4l2-compliance fixes

VIDIOC_DECODER_CMD didn't return EPERM when calling PAUSE or RESUME if no
decoding is in progress.
VIDIOC_G_ENC_INDEX didn't set entries_cap or return 0 if no decoding was
in progress.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] sliced vbi: subdevs shouldn't clear the full v4l2_sliced_vbi_format struct

Various subdevs cleared the full v4l2_sliced_vbi_format struct, when
only the service_set/lines fields should have been cleared.
Due to this the io_size field was wrongly cleared to 0, causing a
v4l2-compliance error.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l2-ctrls: add a filter function to v4l2_ctrl_add_handler

With a filter function you can control more precisely which controls
are added. This is useful in particular for radio device nodes for
combined TV/Radio cards where you want to show just the radio-specific
controls and not controls like brightness.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rtl28xxu: [0ccd:00d3] TerraTec Cinergy T Stick RC (Rev. 3)

It is RTL2832U + E4000.
Thanks to Nikolai Spasov reporting and testing!

Reported-by: Nikolai Spasov <ns@codingrobot.com>
Tested-by: Nikolai Spasov <ns@codingrobot.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] fc2580: use macro for 64 bit division and reminder

Fixes the following warnings on a 32 bit system with GCC 4.4.3 and kernel Ubuntu 2.6.32-43 32 bit:
WARNING: "__udivdi3" [fc2580.ko] undefined!
WARNING: "__umoddi3" [fc2580.ko] undefined!

Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] fc2580: silence uninitialized variable warning

fc2580.c: In function 'fc2580_set_params':
fc2580.c:118: warning: 'ret' may be used uninitialized in this function

Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] fc2580: define const as UL to silence a warning

fc2580.c: In function 'fc2580_set_params':
fc2580.c:150: warning: this decimal constant is unsigned only in ISO C90

Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: do not set PCTV 290e LNA handler if fe attach fail

It was a bug that could cause oops if demodulator attach was
failed.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cxd2820r: use static GPIO config when GPIOLIB is undefined

It is fallback condition as GPIOLIB seems to be disabled by default.
Better solution is needed, maybe GPIOLIB could be enabled by default?

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: implement FE set_lna() callback

Make LNA run-time switching possible for PCTV nanoStick T2 290e!

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] MAINTAINERS: Add stk1160 driver

Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] MAINTAINERS: add modules I am responsible

All those are media modules, mostly digital television drivers.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l2-ioctl.c: fix overlay support

The vidioc_overlay op needs an unsigned int, not an unsigned int pointer.
So we need a small function that dereferences the unsigned int pointer.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media/radio/shark2: Fix build error caused by missing dependencies

Without this patch, building rand-0y2jSKT results in:

WARNING: drivers/usb/musb/musb_hdrc.o(.devinit.text+0x9b8): Section mismatch in reference from the function musb_init_controller() to the function .init.text:dma_controller_create()
The function __devinit musb_init_controller() references
a function __init dma_controller_create().
If dma_controller_create is only used by musb_init_controller then
annotate dma_controller_create with a matching annotation.

ERROR: "snd_tea575x_init" [drivers/media/radio/radio-shark.ko] undefined!
ERROR: "snd_tea575x_exit" [drivers/media/radio/radio-shark.ko] undefined!
make[2]: *** [__modpost] Error 1
make[1]: *** [modules] Error 2
make: *** [sub-make] Error 2

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-mfc: Fix second memory bank alignment

Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Fix setup of initial links to FIMC entities

This patch fixes regression introduced in commit
4af813108b880e96a4b8b01e162f950a4aaa2475. Missing pointers
to the sensor subdevs are restored along with subdev callback
notifications to a corresponding FIMC instance driver.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Fix cast warnings from m5mols_[set/get]_ctrl_mode

Fixes following warnings on 64-bit architectures:

m5mols.h: In function 'm5mols_set_ctrl_mode':
m5mols.h:326:15: warning: cast to pointer from integer of different
size [-Wint-to-pointer-cast]

m5mols.h: In function 'm5mols_get_ctrl_mode':
m5mols.h:331:9: warning: cast from pointer to integer of different
size [-Wpointer-to-int-cast]

drivers/media/i2c/m5mols/m5mols_controls.c:466:2: warning: cast
from pointer to integer of different size

Cc: Heungjun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Add missing free_irq() on error path

Make sure the interrupt is freed when driver probing fails.

Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Don't allocate fimc-m2m video device dynamically

There is no need to to dynamically allocate struct video_device
for the M2M devices, so embed it instead in driver's private
data structure as it is done in case of fimc-capture and fimc-lite,
where it solves some bugs on cleanup paths.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Don't allocate fimc-capture video device dynamically

This fixes potential invalid pointer de-reference, when
media_entity_cleanup() is called before video device
is unregistered.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Don't allocate fimc-lite video device structure dynamically

This fixes potential invalid pointer de-reference, when
media_entity_cleanup() is called after video_unregister_device,
and video device structure memory is already freed.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Enable FIMC-LITE driver only for SOC_EXYNOS4x12

Allow to compile-in the FIMC-LITE driver only on Exynos4212,
Exynos4412 and Exynos5250 SoC where the device is available.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Merge tag 'v3.6' into staging/for_v3.7

Linux 3.6

* tag 'v3.6': (562 commits)
  Linux 3.6
  vfs: dcache: fix deadlock in tree traversal
  mtdchar: fix offset overflow detection
  thp: avoid VM_BUG_ON page_count(page) false positives in __collapse_huge_page_copy
  iommu/amd: Fix wrong assumption in iommu-group specific code
  netdev: octeon: fix return value check in octeon_mgmt_init_phy()
  ALSA: snd-usb: fix next_packet_size calls for pause case
  inetpeer: fix token initialization
  qlcnic: Fix scheduling while atomic bug
  bnx2: Clean up remaining iounmap
  trivial select_parent documentation fix
  net: phy: smsc: Implement PHY config_init for LAN87xx
  smsc75xx: fix resume after device reset
  um: Preinclude include/linux/kern_levels.h
  um: Fix IPC on um
  netdev: pasemi: fix return value check in pasemi_mac_phy_init()
  team: fix return value check
  l2tp: fix return value check
  USB: Fix race condition when removing host controllers
  USB: ohci-at91: fix null pointer in ohci_hcd_at91_overcurrent_irq
  ...

tda1004x: Lock I2C bus during firmware load

tda1004x doesn't allow firmware loads while it is busy with something
else. Avoid it to happen by locking the I2C bus during firmware transfer.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Linux 3.6

vfs: dcache: fix deadlock in tree traversal

IBM reported a deadlock in select_parent().  This was found to be caused
by taking rename_lock when already locked when restarting the tree
traversal.

There are two cases when the traversal needs to be restarted:

 1) concurrent d_move(); this can only happen when not already locked,
    since taking rename_lock protects against concurrent d_move().

 2) racing with final d_put() on child just at the moment of ascending
    to parent; rename_lock doesn't protect against this rare race, so it
    can happen when already locked.

Because of case 2, we need to be able to handle restarting the traversal
when rename_lock is already held.  This patch fixes all three callers of
try_to_ascend().

IBM reported that the deadlock is gone with this patch.

[ I rewrote the patch to be smaller and just do the "goto again" if the
  lock was already held, but credit goes to Miklos for the real work.
   - Linus ]

Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'iommu-fixes-v3.6-rc7' of git://git./linux/kernel/git/joro/iommu

Pull IOMMU fixes from Joerg Roedel:
 "Two small patches:

* One patch to fix the function declarations for
  !CONFIG_IOMMU_API. This is causing build errors
  in linux-next and should be fixed for v3.6.

* Another patch to fix an IOMMU group related NULL pointer
  dereference."

* tag 'iommu-fixes-v3.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/amd: Fix wrong assumption in iommu-group specific code
  iommu: static inline iommu group stub functions

Merge git://git.infradead.org/users/willy/linux-nvme

Pull NVMe driver fixes from Matthew Wilcox:
 "Now that actual hardware has been released (don't have any yet
  myself), people are starting to want some of these fixes merged."

Willy doesn't have hardware? Guys...

* git://git.infradead.org/users/willy/linux-nvme:
  NVMe: Cancel outstanding IOs on queue deletion
  NVMe: Free admin queue memory on initialisation failure
  NVMe: Use ida for nvme device instance
  NVMe: Fix whitespace damage in nvme_init
  NVMe: handle allocation failure in nvme_map_user_pages()
  NVMe: Fix uninitialized iod compiler warning
  NVMe: Do not set IO queue depth beyond device max
  NVMe: Set block queue max sectors
  NVMe: use namespace id for nvme_get_features
  NVMe: replace nvme_ns with nvme_dev for user admin
  NVMe: Fix nvme module init when nvme_major is set
  NVMe: Set request queue logical block size

get_dvb_firmware: fix download site for tda10046 firmware

The previous website doesn't exist anymore. Update it to one site that
actually exists.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

mtdchar: fix offset overflow detection

Sasha Levin has been running trinity in a KVM tools guest, and was able
to trigger the BUG_ON() at arch/x86/mm/pat.c:279 (verifying the range of
the memory type).  The call trace showed that it was mtdchar_mmap() that
created an invalid remap_pfn_range().

The problem is that mtdchar_mmap() does various really odd and subtle
things with the vma page offset etc, and uses the wrong types (and the
wrong overflow) detection for it.

For example, the page offset may well be 32-bit on a 32-bit
architecture, but after shifting it up by PAGE_SHIFT, we need to use a
potentially 64-bit resource_size_t to correctly hold the full value.

Also, we need to check that the vma length plus offset doesn't overflow
before we check that it is smaller than the length of the mtdmap region.

This fixes things up and tries to make the code a bit easier to read.

Reported-and-tested-by: Sasha Levin <levinsasha928@gmail.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Artem Bityutskiy <dedekind1@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge git://git./linux/kernel/git/davem/net

Pull networking fixes from David S Miller:

 1) Netfilter xt_limit module can use uninitialized rules, from Jan
    Engelhardt.

 2) Wei Yongjun has found several more spots where error pointers were
    treated as NULL/non-NULL and vice versa.

 3) bnx2x was converted to pci_io{,un}map() but one remaining plain
    iounmap() got missed.  From Neil Horman.

 4) Due to a fence-post type error in initialization of inetpeer entries
    (which is where we store the ICMP rate limiting information), we can
    erroneously drop ICMPs if the inetpeer was created right around when
    jiffies wraps.

    Fix from Nicolas Dichtel.

 5) smsc75xx resume fix from Steve Glendinnig.

 6) LAN87xx smsc chips need an explicit hardware init, from Marek Vasut.

 7) qlcnic uses msleep() with locks held, fix from Narendra K.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  netdev: octeon: fix return value check in octeon_mgmt_init_phy()
  inetpeer: fix token initialization
  qlcnic: Fix scheduling while atomic bug
  bnx2: Clean up remaining iounmap
  net: phy: smsc: Implement PHY config_init for LAN87xx
  smsc75xx: fix resume after device reset
  netdev: pasemi: fix return value check in pasemi_mac_phy_init()
  team: fix return value check
  l2tp: fix return value check
  netfilter: xt_limit: have r->cost != 0 case work

Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs

Pull vfs fixes from Al Viro:
 "A couple of fixes; one for automount/lazy umount race, another a
  classic "we don't protect the refcount transition to zero with the
  lock that protects looking for object in hash" kind of crap in lockd."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  close the race in nlmsvc_free_block()
  do_add_mount()/umount -l races

Merge branch 'for-linus-3.6-rc-final' of git://git./linux/kernel/git/rw/uml

Pull UML fixes from Richard Weinberger.

* 'for-linus-3.6-rc-final' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: Preinclude include/linux/kern_levels.h
  um: Fix IPC on um
  um: kill thread->forking
  um: let signal_delivered() do SIGTRAP on singlestepping into handler
  um: don't leak floating point state and segment registers on execve()
  um: take cleaning singlestep to start_thread()

Merge tag 'dm-3.6-fixes' of git://git./linux/kernel/git/agk/linux-dm

Pull dm fixes from Alasdair G Kergon:
 "A few fixes for problems discovered during the 3.6 cycle.

  Of particular note, are fixes to the thin target's discard support,
  which I hope is finally working correctly; and fixes for multipath
  ioctls and device limits when there are no paths."

* tag 'dm-3.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
  dm verity: fix overflow check
  dm thin: fix discard support for data devices
  dm thin: tidy discard support
  dm: retain table limits when swapping to new table with no devices
  dm table: clear add_random unless all devices have it set
  dm: handle requests beyond end of device instead of using BUG_ON
  dm mpath: only retry ioctl when no paths if queue_if_no_path set
  dm thin: do not set discard_zeroes_data

thp: avoid VM_BUG_ON page_count(page) false positives in __collapse_huge_page_copy

Speculative cache pagecache lookups can elevate the refcount from
under us, so avoid the false positive. If the refcount is < 2 we'll be
notified by a VM_BUG_ON in put_page_testzero as there are two
put_page(src_page) in a row before returning from this function.

Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Petr Holasek <pholasek@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

iommu/amd: Fix wrong assumption in iommu-group specific code

The new IOMMU groups code in the AMD IOMMU driver makes the
assumption that there is a pci_dev struct available for all
device-ids listed in the IVRS ACPI table. Unfortunatly this
assumption is not true and so this code causes a NULL
pointer dereference at boot on some systems.

Fix it by making sure the given pointer is never NULL when
passed to the group specific code. The real fix is larger
and will be queued for v3.7.

Reported-by: Florian Dazinger <florian@dazinger.net>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>

netdev: octeon: fix return value check in octeon_mgmt_init_phy()

In case of error, the function of_phy_connect() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux

Pull drm fixes from Dave Airlie:
 "The three nouveau fixes quiten unneeded dmesg spam that people are
   seeing and pondering,

  The udl fix stops it from trying to driver monitors that are too big,
  where we get a black screen.

  And a vmware memory alloc problem."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/nvc0/fifo: ignore bits in PFIFO_INTR that aren't set in PFIFO_INTR_EN
  drm/udl: limit modes to the sku pixel limits.
  vmwgfx: corruption in vmw_event_fence_action_create()
  drm/nvc0/ltcg: mask off intr 0x10
  drm/nouveau: silence a debug message triggered by newer userspace

Merge tag 'usb-3.6-rc7' of git://git./linux/kernel/git/gregkh/usb

Pull USB fixes from Greg Kroah-Hartman:
 "Here are two USB bugfixes for your 3.6-rc7 tree.

  The OHCI fix has been reported a number of times and is a regression
  from 3.5, and the patch that causes the regression was on the way to
  the -stable trees before I was reminded (again) that this fix needed
  to get to your tree soon.

  The host controller bugfix was reported in older kernels as being
  pretty easy to trigger, and has been tested by Red Hat and their
  customers.

  Both have been in the usb-next branch in the -next tree for a while
  now, I just cherry-picked them out to get to you in time for the 3.6
  release.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: Fix race condition when removing host controllers
  USB: ohci-at91: fix null pointer in ohci_hcd_at91_overcurrent_irq

ALSA: snd-usb: fix next_packet_size calls for pause case

Also fix the calls to next_packet_size() for the pause case. This was
missed in 245baf983 ("ALSA: snd-usb: fix calls to next_packet_size").

Signed-off-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reported-and-tested-by: Christian Tefzer <ctrefzer@gmx.de>
Cc: stable@kernel.org
[ Taking directly because Takashi is on vacation  - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'asoc-3.6' of git://git./linux/kernel/git/broonie/sound

Pull ASoC update from Mark Brown:
 "One small and obvious driver-specific fix.

  Takashi is on vacation now so he asked me to send directly, it's a
  pretty bad bug with low regression risk."

* tag 'asoc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound:
  ASoC: wm2000: Correct register size

inetpeer: fix token initialization

When jiffies wraps around (for example, 5 minutes after the boot, see
INITIAL_JIFFIES) and peer has just been created, now - peer->rate_last can be
< XRLIM_BURST_FACTOR * timeout, so token is not set to the maximum value, thus
some icmp packets can be unexpectedly dropped.

Fix this case by initializing last_rate to 60 seconds in the past.

Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: Fix scheduling while atomic bug

In the device close path, 'qlcnic_fw_destroy_ctx' and
'qlcnic_poll_rsp' call msleep. But  'qlcnic_fw_destroy_ctx' and
'qlcnic_poll_rsp' are called with 'adapter->tx_clean_lock' spin lock
held resulting in scheduling while atomic bug causing the following
trace.

I observed that the commit 012dc19a45b2b9cc2ebd14aaa401cf782c2abba4
from John Fastabend addresses a similar issue in ixgbevf driver.
Adopting the same approach used in the commit, this patch uses mdelay
to address the issue.

[79884.999115] BUG: scheduling while atomic: ip/30846/0x00000002
[79885.005562] INFO: lockdep is turned off.
[79885.009958] Modules linked in: qlcnic fuse nf_conntrack_netbios_ns nf_conntrack_broadcast ipt_MASQUERADE bnep bluetooth rfkill ip6table_mangle ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter ip6_tables iptable_nat nf_nat iptable_mangle ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack iptable_filter ip_tables dcdbas coretemp kvm_intel kvm iTCO_wdt ixgbe iTCO_vendor_support crc32c_intel ghash_clmulni_intel nfsd microcode sb_edac pcspkr edac_core dca bnx2x shpchp auth_rpcgss nfs_acl lpc_ich mfd_core mdio lockd libcrc32c wmi acpi_pad acpi_power_meter sunrpc uinput sd_mod sr_mod cdrom crc_t10dif ahci libahci libata megaraid_sas usb_storage dm_mirror dm_region_hash dm_log dm_mod [last unloaded: qlcnic]
[79885.083608] Pid: 30846, comm: ip Tainted: G        W  O 3.6.0-rc7+ #1
[79885.090805] Call Trace:
[79885.093569]  [<ffffffff816764d8>] __schedule_bug+0x68/0x76
[79885.099699]  [<ffffffff8168358e>] __schedule+0x99e/0xa00
[79885.105634]  [<ffffffff81683929>] schedule+0x29/0x70
[79885.111186]  [<ffffffff81680def>] schedule_timeout+0x16f/0x350
[79885.117724]  [<ffffffff811afb7a>] ? init_object+0x4a/0x90
[79885.123770]  [<ffffffff8107c190>] ? __internal_add_timer+0x140/0x140
[79885.130873]  [<ffffffff81680fee>] schedule_timeout_uninterruptible+0x1e/0x20
[79885.138773]  [<ffffffff8107e830>] msleep+0x20/0x30
[79885.144159]  [<ffffffffa04c7fbf>] qlcnic_issue_cmd+0xef/0x290 [qlcnic]
[79885.151478]  [<ffffffffa04c8265>] qlcnic_fw_cmd_destroy_rx_ctx+0x55/0x90 [qlcnic]
[79885.159868]  [<ffffffffa04c92fd>] qlcnic_fw_destroy_ctx+0x2d/0xa0 [qlcnic]
[79885.167576]  [<ffffffffa04bf2ed>] __qlcnic_down+0x11d/0x180 [qlcnic]
[79885.174708]  [<ffffffffa04bf6f8>] qlcnic_close+0x18/0x20 [qlcnic]
[79885.181547]  [<ffffffff8153b4c5>] __dev_close_many+0x95/0xe0
[79885.187899]  [<ffffffff8153b548>] __dev_close+0x38/0x50
[79885.193761]  [<ffffffff81545101>] __dev_change_flags+0xa1/0x180
[79885.200419]  [<ffffffff81545298>] dev_change_flags+0x28/0x70
[79885.206779]  [<ffffffff815531b8>] do_setlink+0x378/0xa00
[79885.212731]  [<ffffffff81354fe1>] ? nla_parse+0x31/0xe0
[79885.218612]  [<ffffffff815558ee>] rtnl_newlink+0x37e/0x560
[79885.224768]  [<ffffffff812cfa19>] ? selinux_capable+0x39/0x50
[79885.231217]  [<ffffffff812cbf98>] ? security_capable+0x18/0x20
[79885.237765]  [<ffffffff81555114>] rtnetlink_rcv_msg+0x114/0x2f0
[79885.244412]  [<ffffffff81551f87>] ? rtnl_lock+0x17/0x20
[79885.250280]  [<ffffffff81551f87>] ? rtnl_lock+0x17/0x20
[79885.256148]  [<ffffffff81555000>] ? __rtnl_unlock+0x20/0x20
[79885.262413]  [<ffffffff81570fc1>] netlink_rcv_skb+0xa1/0xb0
[79885.268661]  [<ffffffff81551fb5>] rtnetlink_rcv+0x25/0x40
[79885.274727]  [<ffffffff815708bd>] netlink_unicast+0x19d/0x220
[79885.281146]  [<ffffffff81570c45>] netlink_sendmsg+0x305/0x3f0
[79885.287595]  [<ffffffff8152b188>] ? sock_update_classid+0x148/0x2e0
[79885.294650]  [<ffffffff81525c2c>] sock_sendmsg+0xbc/0xf0
[79885.300600]  [<ffffffff8152600c>] __sys_sendmsg+0x3ac/0x3c0
[79885.306853]  [<ffffffff8109be23>] ? up_read+0x23/0x40
[79885.312510]  [<ffffffff816896cc>] ? do_page_fault+0x2bc/0x570
[79885.318968]  [<ffffffff81191854>] ? sys_brk+0x44/0x150
[79885.324715]  [<ffffffff811c458c>] ? fget_light+0x24c/0x520
[79885.330875]  [<ffffffff815286f9>] sys_sendmsg+0x49/0x90
[79885.336707]  [<ffffffff8168e429>] system_call_fastpath+0x16/0x1b

Signed-off-by: Narendra K <narendra_k@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2: Clean up remaining iounmap

commit c0357e975afdbbedab5c662d19bef865f02adc17 modified bnx2 to switch from
using ioremap/iounmap to pci_iomap/pci_iounmap.  They missed a spot in the error
path of bnx2_init_one though.  This patch just cleans that up.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Michael Chan <mcan@broadcom.com>
CC: "David S. Miller" <davem@davemloft.net>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>