Romain Izard [Fri, 22 Mar 2019 15:53:02 +0000 (16:53 +0100)]
usb: cdc-acm: fix race during wakeup blocking TX traffic
commit
93e1c8a638308980309e009cc40b5a57ef87caf1 upstream.
When the kernel is compiled with preemption enabled, the URB completion
handler can run in parallel with the work responsible for waking up the
tty layer. If the URB handler sets the EVENT_TTY_WAKEUP bit during the
call to tty_port_tty_wakeup() to signal that there is room for additional
input, it will be cleared at the end of this call. As a result, TX traffic
on the upper layer will be blocked.
This can be seen with a kernel configured with CONFIG_PREEMPT, and a fast
modem connected with PPP running over a USB CDC-ACM port.
Use test_and_clear_bit() instead, which ensures that each wakeup requested
by the URB completion code will trigger a call to tty_port_tty_wakeup().
Fixes:
1aba579f3cf5 cdc-acm: handle read pipe errors
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Fri, 22 Mar 2019 15:50:15 +0000 (17:50 +0200)]
xhci: Fix port resume done detection for SS ports with LPM enabled
commit
6cbcf596934c8e16d6288c7cc62dfb7ad8eadf15 upstream.
A suspended SS port in U3 link state will go to U0 when resumed, but
can almost immediately after that enter U1 or U2 link power save
states before host controller driver reads the port status.
Host controller driver only checks for U0 state, and might miss
the finished resume, leaving flags unclear and skip notifying usb
code of the wake.
Add U1 and U2 to the possible link states when checking for finished
port resume.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yasushi Asano [Mon, 18 Feb 2019 10:26:34 +0000 (11:26 +0100)]
usb: host: xhci-rcar: Add XHCI_TRUST_TX_LENGTH quirk
commit
40fc165304f0faaae78b761f8ee30b5d216b1850 upstream.
When plugging BUFFALO LUA4-U3-AGT USB3.0 to Gigabit Ethernet LAN
Adapter, warning messages filled up dmesg.
[ 101.098287] xhci-hcd
ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
[ 101.117463] xhci-hcd
ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
[ 101.136513] xhci-hcd
ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
Adding the XHCI_TRUST_TX_LENGTH quirk resolves the issue.
Signed-off-by: Yasushi Asano <yasano@jp.adit-jv.com>
Signed-off-by: Spyridon Papageorgiou <spapageorgiou@de.adit-jv.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fabrizio Castro [Fri, 1 Mar 2019 11:05:45 +0000 (11:05 +0000)]
usb: common: Consider only available nodes for dr_mode
commit
238e0268c82789e4c107a37045d529a6dbce51a9 upstream.
There are cases where multiple device tree nodes point to the
same phy node by means of the "phys" property, but we should
only consider those nodes that are marked as available rather
than just any node.
Fixes:
98bfb3946695 ("usb: of: add an api to get dr_mode by the phy node")
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Radoslav Gerganov [Tue, 5 Mar 2019 10:10:34 +0000 (10:10 +0000)]
USB: gadget: f_hid: fix deadlock in f_hidg_write()
commit
072684e8c58d17e853f8e8b9f6d9ce2e58d2b036 upstream.
In f_hidg_write() the write_spinlock is acquired before calling
usb_ep_queue() which causes a deadlock when dummy_hcd is being used.
This is because dummy_queue() callbacks into f_hidg_req_complete() which
tries to acquire the same spinlock. This is (part of) the backtrace when
the deadlock occurs:
0xffffffffc06b1410 in f_hidg_req_complete
0xffffffffc06a590a in usb_gadget_giveback_request
0xffffffffc06cfff2 in dummy_queue
0xffffffffc06a4b96 in usb_ep_queue
0xffffffffc06b1eb6 in f_hidg_write
0xffffffff8127730b in __vfs_write
0xffffffff812774d1 in vfs_write
0xffffffff81277725 in SYSC_write
Fix this by releasing the write_spinlock before calling usb_ep_queue()
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: stable@vger.kernel.org # 4.11+
Fixes:
749494b6bdbb ("usb: gadget: f_hid: fix: Move IN request allocation to set_alt()")
Signed-off-by: Radoslav Gerganov <rgerganov@vmware.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnd Bergmann [Mon, 25 Mar 2019 13:54:30 +0000 (14:54 +0100)]
usb: mtu3: fix EXTCON dependency
commit
3d54d10c6afed34fd45b852bf76f55e8da31d8ef upstream.
When EXTCON is a loadable module, mtu3 fails to link as built-in:
drivers/usb/mtu3/mtu3_plat.o: In function `mtu3_probe':
mtu3_plat.c:(.text+0x690): undefined reference to `extcon_get_edev_by_phandle'
Add a Kconfig dependency to force mtu3 also to be a loadable module
if extconn is, but still allow it to be built without extcon.
Fixes:
d0ed062a8b75 ("usb: mtu3: dual-role mode support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chen-Yu Tsai [Fri, 22 Mar 2019 08:51:07 +0000 (16:51 +0800)]
phy: sun4i-usb: Support set_mode to USB_HOST for non-OTG PHYs
commit
1396929e8a903db80425343cacca766a18ad6409 upstream.
While only the first PHY supports mode switching, the remaining PHYs
work in USB host mode. They should support set_mode with mode=USB_HOST
instead of failing. This is especially needed now that the USB core does
set_mode for all USB ports, which was added in commit
b97a31348379 ("usb:
core: comply to PHY framework").
Make set_mode with mode=USB_HOST a no-op instead of failing for the
non-OTG USB PHYs.
Fixes:
6ba43c291961 ("phy-sun4i-usb: Add support for phy_set_mode")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Axel Lin [Mon, 11 Mar 2019 13:29:37 +0000 (21:29 +0800)]
gpio: adnp: Fix testing wrong value in adnp_gpio_direction_input
commit
c5bc6e526d3f217ed2cc3681d256dc4a2af4cc2b upstream.
Current code test wrong value so it does not verify if the written
data is correctly read back. Fix it.
Also make it return -EPERM if read value does not match written bit,
just like it done for adnp_gpio_direction_output().
Fixes:
5e969a401a01 ("gpio: Add Avionic Design N-bit GPIO expander support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kangjie Lu [Sat, 9 Mar 2019 04:07:57 +0000 (22:07 -0600)]
gpio: exar: add a check for the return value of ida_simple_get fails
commit
7ecced0934e574b528a1ba6c237731e682216a74 upstream.
ida_simple_get may fail and return a negative error number.
The fix checks its return value; if it fails, go to err_destroy.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Biggers [Tue, 26 Feb 2019 21:44:51 +0000 (13:44 -0800)]
drm/vgem: fix use-after-free when drm_gem_handle_create() fails
commit
21d2b122732318b48c10b7262e15595ce54511d3 upstream.
If drm_gem_handle_create() fails in vgem_gem_create(), then the
drm_vgem_gem_object is freed twice: once when the reference is dropped
by drm_gem_object_put_unlocked(), and again by __vgem_gem_destroy().
This was hit by syzkaller using fault injection.
Fix it by skipping the second free.
Reported-by: syzbot+e73f2fb5ed5a5df36d33@syzkaller.appspotmail.com
Fixes:
af33a9190d02 ("drm/vgem: Enable dmabuf import interfaces")
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190226214451.195123-1-ebiggers@kernel.org
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
YueHaibing [Fri, 29 Mar 2019 03:44:40 +0000 (20:44 -0700)]
fs/proc/proc_sysctl.c: fix NULL pointer dereference in put_links
commit
23da9588037ecdd4901db76a5b79a42b529c4ec3 upstream.
Syzkaller reports:
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN PTI
CPU: 1 PID: 5373 Comm: syz-executor.0 Not tainted 5.0.0-rc8+ #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
RIP: 0010:put_links+0x101/0x440 fs/proc/proc_sysctl.c:1599
Code: 00 0f 85 3a 03 00 00 48 8b 43 38 48 89 44 24 20 48 83 c0 38 48 89 c2 48 89 44 24 28 48 b8 00 00 00 00 00 fc ff df 48 c1 ea 03 <80> 3c 02 00 0f 85 fe 02 00 00 48 8b 74 24 20 48 c7 c7 60 2a 9d 91
RSP: 0018:
ffff8881d828f238 EFLAGS:
00010202
RAX:
dffffc0000000000 RBX:
ffff8881e01b1140 RCX:
ffffffff8ee98267
RDX:
0000000000000007 RSI:
ffffc90001479000 RDI:
ffff8881e01b1178
RBP:
dffffc0000000000 R08:
ffffed103ee27259 R09:
ffffed103ee27259
R10:
0000000000000001 R11:
ffffed103ee27258 R12:
fffffffffffffff4
R13:
0000000000000006 R14:
ffff8881f59838c0 R15:
dffffc0000000000
FS:
00007f072254f700(0000) GS:
ffff8881f7100000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00007fff8b286668 CR3:
00000001f0542002 CR4:
00000000007606e0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
PKRU:
55555554
Call Trace:
drop_sysctl_table+0x152/0x9f0 fs/proc/proc_sysctl.c:1629
get_subdir fs/proc/proc_sysctl.c:1022 [inline]
__register_sysctl_table+0xd65/0x1090 fs/proc/proc_sysctl.c:1335
br_netfilter_init+0xbc/0x1000 [br_netfilter]
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x462e99
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:
00007f072254ec58 EFLAGS:
00000246 ORIG_RAX:
0000000000000139
RAX:
ffffffffffffffda RBX:
000000000073bf00 RCX:
0000000000462e99
RDX:
0000000000000000 RSI:
0000000020000280 RDI:
0000000000000003
RBP:
00007f072254ec70 R08:
0000000000000000 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000246 R12:
00007f072254f6bc
R13:
00000000004bcefa R14:
00000000006f6fb0 R15:
0000000000000004
Modules linked in: br_netfilter(+) dvb_usb_dibusb_mc_common dib3000mc dibx000_common dvb_usb_dibusb_common dvb_usb_dw2102 dvb_usb classmate_laptop palmas_regulator cn videobuf2_v4l2 v4l2_common snd_soc_bd28623 mptbase snd_usb_usx2y snd_usbmidi_lib snd_rawmidi wmi libnvdimm lockd sunrpc grace rc_kworld_pc150u rc_core rtc_da9063 sha1_ssse3 i2c_cros_ec_tunnel adxl34x_spi adxl34x nfnetlink lib80211 i5500_temp dvb_as102 dvb_core videobuf2_common videodev media videobuf2_vmalloc videobuf2_memops udc_core lnbp22 leds_lp3952 hid_roccat_ryos s1d13xxxfb mtd vport_geneve openvswitch nf_conncount nf_nat_ipv6 nsh geneve udp_tunnel ip6_udp_tunnel snd_soc_mt6351 sis_agp phylink snd_soc_adau1761_spi snd_soc_adau1761 snd_soc_adau17x1 snd_soc_core snd_pcm_dmaengine ac97_bus snd_compress snd_soc_adau_utils snd_soc_sigmadsp_regmap snd_soc_sigmadsp raid_class hid_roccat_konepure hid_roccat_common hid_roccat c2port_duramar2150 core mdio_bcm_unimac iptable_security iptable_raw iptable_mangle
iptable_nat nf_nat_ipv4 nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 iptable_filter bpfilter ip6_vti ip_vti ip_gre ipip sit tunnel4 ip_tunnel hsr veth netdevsim devlink vxcan batman_adv cfg80211 rfkill chnl_net caif nlmon dummy team bonding vcan bridge stp llc ip6_gre gre ip6_tunnel tunnel6 tun crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel joydev mousedev ide_pci_generic piix aesni_intel aes_x86_64 ide_core crypto_simd atkbd cryptd glue_helper serio_raw ata_generic pata_acpi i2c_piix4 floppy sch_fq_codel ip_tables x_tables ipv6 [last unloaded: lm73]
Dumping ftrace buffer:
(ftrace buffer empty)
---[ end trace
770020de38961fd0 ]---
A new dir entry can be created in get_subdir and its 'header->parent' is
set to NULL. Only after insert_header success, it will be set to 'dir',
otherwise 'header->parent' is set to NULL and drop_sysctl_table is called.
However in err handling path of get_subdir, drop_sysctl_table also be
called on 'new->header' regardless its value of parent pointer. Then
put_links is called, which triggers NULL-ptr deref when access member of
header->parent.
In fact we have multiple error paths which call drop_sysctl_table() there,
upon failure on insert_links() we also call drop_sysctl_table().And even
in the successful case on __register_sysctl_table() we still always call
drop_sysctl_table().This patch fix it.
Link: http://lkml.kernel.org/r/20190314085527.13244-1-yuehaibing@huawei.com
Fixes:
0e47c99d7fe25 ("sysctl: Replace root_list with links between sysctl_table_sets")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: <stable@vger.kernel.org> [3.4+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wentao Wang [Wed, 20 Mar 2019 15:30:39 +0000 (15:30 +0000)]
Disable kgdboc failed by echo space to /sys/module/kgdboc/parameters/kgdboc
commit
3ec8002951ea173e24b466df1ea98c56b7920e63 upstream.
Echo "" to /sys/module/kgdboc/parameters/kgdboc will fail with "No such
device” error.
This is caused by function "configure_kgdboc" who init err to ENODEV
when the config is empty (legal input) the code go out with ENODEV
returned.
Fixes:
2dd453168643 ("kgdboc: Fix restrict error")
Signed-off-by: Wentao Wang <witallwang@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork [Wed, 27 Mar 2019 14:25:32 +0000 (15:25 +0100)]
USB: serial: option: add Olicard 600
commit
84f3b43f7378b98b7e3096d5499de75183d4347c upstream.
This is a Qualcomm based device with a QMI function on interface 4.
It is mode switched from 2020:2030 using a standard eject message.
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2020 ProdID=2031 Rev= 2.32
S: Manufacturer=Mobile Connect
S: Product=Mobile Connect
S: SerialNumber=
0123456789ABCDEF
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
Cc: stable@vger.kernel.org
Signed-off-by: Bjørn Mork <bjorn@mork.no>
[ johan: use tabs to align comments in adjacent lines ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kristian Evensen [Sat, 2 Mar 2019 12:35:53 +0000 (13:35 +0100)]
USB: serial: option: add support for Quectel EM12
commit
d1252f0237238b912c3e7a51bf237acf34c97983 upstream.
The Quectel EM12 is a Cat. 12 LTE modem. It behaves in the exactly the
same way as the EP06 (including the dynamic configuration behavior), so
the same checks on reserved interfaces, etc. are needed.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mans Rullgard [Tue, 26 Feb 2019 17:07:10 +0000 (17:07 +0000)]
USB: serial: option: set driver_info for SIM5218 and compatibles
commit
f8df5c2c3e2df5ffaf9fb5503da93d477a8c7db4 upstream.
The SIMCom SIM5218 and compatible devices have 5 USB interfaces, only 4
of which are serial ports. The fifth is a network interface supported
by the qmi-wwan driver. Furthermore, the serial ports do not support
modem control signals. Add driver_info flags to reflect this.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Fixes:
ec0cd94d881c ("usb: option: add SIMCom SIM5218")
Cc: stable <stable@vger.kernel.org> # 3.2
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lin Yi [Wed, 20 Mar 2019 11:04:56 +0000 (19:04 +0800)]
USB: serial: mos7720: fix mos_parport refcount imbalance on error path
commit
2908b076f5198d231de62713cb2b633a3a4b95ac upstream.
The write_parport_reg_nonblock() helper takes a reference to the struct
mos_parport, but failed to release it in a couple of error paths after
allocation failures, leading to a memory leak.
Johan said that move the kref_get() and mos_parport assignment to the
end of urbtrack initialisation is a better way, so move it. and
mos_parport do not used until urbtrack initialisation.
Signed-off-by: Lin Yi <teroincn@163.com>
Fixes:
b69578df7e98 ("USB: usbserial: mos7720: add support for parallel port on moschip 7715")
Cc: stable <stable@vger.kernel.org> # 2.6.35
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
George McCollister [Tue, 5 Mar 2019 22:05:03 +0000 (16:05 -0600)]
USB: serial: ftdi_sio: add additional NovaTech products
commit
422c2537ba9d42320f8ab6573940269f87095320 upstream.
Add PIDs for the NovaTech OrionLX+ and Orion I/O so they can be
automatically detected.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Wed, 27 Mar 2019 01:11:14 +0000 (10:11 +0900)]
USB: serial: cp210x: add new device id
commit
a595ecdd5f60b2d93863cebb07eec7f935839b54 upstream.
Lorenz Messtechnik has a device that is controlled by the cp210x driver,
so add the device id to the driver. The device id was provided by
Silicon-Labs for the devices from this vendor.
Reported-by: Uli <t9cpu@web.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hoan Nguyen An [Mon, 18 Mar 2019 09:26:32 +0000 (18:26 +0900)]
serial: sh-sci: Fix setting SCSCR_TIE while transferring data
commit
93bcefd4c6bad4c69dbc4edcd3fbf774b24d930d upstream.
We disable transmission interrupt (clear SCSCR_TIE) after all data has been transmitted
(if uart_circ_empty(xmit)). While transmitting, if the data is still in the tty buffer,
re-enable the SCSCR_TIE bit, which was done at sci_start_tx().
This is unnecessary processing, wasting CPU operation if the data transmission length is large.
And further, transmit end, FIFO empty bits disabling have also been performed in the step above.
Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aditya Pakki [Mon, 18 Mar 2019 23:44:14 +0000 (18:44 -0500)]
serial: max310x: Fix to avoid potential NULL pointer dereference
commit
3a10e3dd52e80b9a97a3346020024d17b2c272d6 upstream.
of_match_device can return a NULL pointer when matching device is not
found. This patch avoids a scenario causing NULL pointer derefernce.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Malcolm Priestley [Sun, 24 Mar 2019 18:53:49 +0000 (18:53 +0000)]
staging: vt6655: Fix interrupt race condition on device start up.
commit
3b9c2f2e0e99bb67c96abcb659b3465efe3bee1f upstream.
It appears on some slower systems that the driver can find its way
out of the workqueue while the interrupt is disabled by continuous polling
by it.
Move MACvIntEnable to vnt_interrupt_work so that it is always enabled
on all routes out of vnt_interrupt_process.
Move MACvIntDisable so that the device doesn't keep polling the system
while the workqueue is being processed.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
CC: stable@vger.kernel.org # v4.2+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Malcolm Priestley [Wed, 27 Mar 2019 18:45:26 +0000 (18:45 +0000)]
staging: vt6655: Remove vif check from vnt_interrupt
commit
cc26358f89c3e493b54766b1ca56cfc6b14db78a upstream.
A check for vif is made in vnt_interrupt_work.
There is a small chance of leaving interrupt disabled while vif
is NULL and the work hasn't been scheduled.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
CC: stable@vger.kernel.org # v4.2+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ian Abbott [Mon, 4 Mar 2019 14:33:54 +0000 (14:33 +0000)]
staging: comedi: ni_mio_common: Fix divide-by-zero for DIO cmdtest
commit
bafd9c64056cd034a1174dcadb65cd3b294ff8f6 upstream.
`ni_cdio_cmdtest()` validates Comedi asynchronous commands for the DIO
subdevice (subdevice 2) of supported National Instruments M-series
cards. It is called when handling the `COMEDI_CMD` and `COMEDI_CMDTEST`
ioctls for this subdevice. There are two causes for a possible
divide-by-zero error when validating that the `stop_arg` member of the
passed-in command is not too large.
The first cause for the divide-by-zero is that calls to
`comedi_bytes_per_scan()` are only valid once the command has been
copied to `s->async->cmd`, but that copy is only done for the
`COMEDI_CMD` ioctl. For the `COMEDI_CMDTEST` ioctl, it will use
whatever was left there by the previous `COMEDI_CMD` ioctl, if any.
(This is very likely, as it is usual for the application to use
`COMEDI_CMDTEST` before `COMEDI_CMD`.) If there has been no previous,
valid `COMEDI_CMD` for this subdevice, then `comedi_bytes_per_scan()`
will return 0, so the subsequent division in `ni_cdio_cmdtest()` of
`s->async->prealloc_bufsz / comedi_bytes_per_scan(s)` will be a
divide-by-zero error. To fix this error, call a new function
`comedi_bytes_per_scan_cmd(s, cmd)`, based on the existing
`comedi_bytes_per_scan(s)` but using a specified `struct comedi_cmd` for
its calculations. (Also refactor `comedi_bytes_per_scan()` to call the
new function.)
Once the first cause for the divide-by-zero has been fixed, the second
cause is that `comedi_bytes_per_scan_cmd()` can legitimately return 0 if
the `scan_end_arg` member of the `struct comedi_cmd` being tested is 0.
Fix it by only performing the division (and validating that `stop_arg`
is no more than the maximum value) if `comedi_bytes_per_scan_cmd()`
returns a non-zero value.
The problem was reported on the COMEDI mailing list here:
https://groups.google.com/forum/#!topic/comedi_list/4t9WlHzMhKM
Reported-by: Ivan Vasilyev <grabesstimme@gmail.com>
Tested-by: Ivan Vasilyev <grabesstimme@gmail.com>
Fixes:
f164cbf98fa8 ("staging: comedi: ni_mio_common: add finite regeneration to dio output")
Cc: <stable@vger.kernel.org> # 4.6+
Cc: Spencer E. Olson <olsonse@umich.edu>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kangjie Lu [Fri, 15 Mar 2019 17:16:06 +0000 (12:16 -0500)]
tty: atmel_serial: fix a potential NULL pointer dereference
commit
c85be041065c0be8bc48eda4c45e0319caf1d0e5 upstream.
In case dmaengine_prep_dma_cyclic fails, the fix returns a proper
error code to avoid NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Fixes:
34df42f59a60 ("serial: at91: add rx dma support")
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steffen Maier [Tue, 26 Mar 2019 13:36:59 +0000 (14:36 +0100)]
scsi: zfcp: fix scsi_eh host reset with port_forced ERP for non-NPIV FCP devices
commit
242ec1455151267fe35a0834aa9038e4c4670884 upstream.
Suppose more than one non-NPIV FCP device is active on the same channel.
Send I/O to storage and have some of the pending I/O run into a SCSI
command timeout, e.g. due to bit errors on the fibre. Now the error
situation stops. However, we saw FCP requests continue to timeout in the
channel. The abort will be successful, but the subsequent TUR fails.
Scsi_eh starts. The LUN reset fails. The target reset fails. The host
reset only did an FCP device recovery. However, for non-NPIV FCP devices,
this does not close and reopen ports on the SAN-side if other non-NPIV FCP
device(s) share the same open ports.
In order to resolve the continuing FCP request timeouts, we need to
explicitly close and reopen ports on the SAN-side.
This was missing since the beginning of zfcp in v2.6.0 history commit
ea127f975424 ("[PATCH] s390 (7/7): zfcp host adapter.").
Note: The FSF requests for forced port reopen could run into FSF request
timeouts due to other reasons. This would trigger an internal FCP device
recovery. Pending forced port reopen recoveries would get dismissed. So
some ports might not get fully reopened during this host reset handler.
However, subsequent I/O would trigger the above described escalation and
eventually all ports would be forced reopen to resolve any continuing FCP
request timeouts due to earlier bit errors.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: <stable@vger.kernel.org> #3.0+
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steffen Maier [Tue, 26 Mar 2019 13:36:58 +0000 (14:36 +0100)]
scsi: zfcp: fix rport unblock if deleted SCSI devices on Scsi_Host
commit
fe67888fc007a76b81e37da23ce5bd8fb95890b0 upstream.
An already deleted SCSI device can exist on the Scsi_Host and remain there
because something still holds a reference. A new SCSI device with the same
H:C:T:L and FCP device, target port WWPN, and FCP LUN can be created. When
we try to unblock an rport, we still find the deleted SCSI device and
return early because the zfcp_scsi_dev of that SCSI device is not
ZFCP_STATUS_COMMON_UNBLOCKED. Hence we miss to unblock the rport, even if
the new proper SCSI device would be in good state.
Therefore, skip deleted SCSI devices when iterating the sdevs of the shost.
[cf. __scsi_device_lookup{_by_target}() or scsi_device_get()]
The following abbreviated trace sequence can indicate such problem:
Area : REC
Tag : ersfs_3
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x40000000 not ZFCP_STATUS_COMMON_UNBLOCKED
Ready count : n not incremented yet
Running count : 0x00000000
ERP want : 0x01
ERP need : 0xc1 ZFCP_ERP_ACTION_NONE
Area : REC
Tag : ersfs_3
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x41000000
Ready count : n+1
Running count : 0x00000000
ERP want : 0x01
ERP need : 0x01
...
Area : REC
Level : 4 only with increased trace level
Tag : ertru_l
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x40000000
Request ID : 0x0000000000000000
ERP status : 0x01800000
ERP step : 0x1000
ERP action : 0x01
ERP count : 0x00
NOT followed by a trace record with tag "scpaddy"
for WWPN 0x50050763031bd327.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes:
6f2ce1c6af37 ("scsi: zfcp: fix rport unblock race with LUN recovery")
Cc: <stable@vger.kernel.org> #2.6.32+
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Martin K. Petersen [Wed, 27 Mar 2019 16:11:52 +0000 (12:11 -0400)]
scsi: sd: Quiesce warning if device does not report optimal I/O size
commit
1d5de5bd311be7cd54f02f7cd164f0349a75c876 upstream.
Commit
a83da8a4509d ("scsi: sd: Optimal I/O size should be a multiple
of physical block size") split one conditional into several separate
statements in an effort to provide more accurate warning messages when
a device reports a nonsensical value. However, this reorganization
accidentally dropped the precondition of the reported value being
larger than zero. This lead to a warning getting emitted on devices
that do not report an optimal I/O size at all.
Remain silent if a device does not report an optimal I/O size.
Fixes:
a83da8a4509d ("scsi: sd: Optimal I/O size should be a multiple of physical block size")
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: <stable@vger.kernel.org>
Reported-by: Hussam Al-Tayeb <ht990332@gmx.com>
Tested-by: Hussam Al-Tayeb <ht990332@gmx.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bart Van Assche [Mon, 25 Mar 2019 17:01:46 +0000 (10:01 -0700)]
scsi: sd: Fix a race between closing an sd device and sd I/O
commit
c14a57264399efd39514a2329c591a4b954246d8 upstream.
The scsi_end_request() function calls scsi_cmd_to_driver() indirectly and
hence needs the disk->private_data pointer. Avoid that that pointer is
cleared before all affected I/O requests have finished. This patch avoids
that the following crash occurs:
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000000
Call trace:
scsi_mq_uninit_cmd+0x1c/0x30
scsi_end_request+0x7c/0x1b8
scsi_io_completion+0x464/0x668
scsi_finish_command+0xbc/0x160
scsi_eh_flush_done_q+0x10c/0x170
sas_scsi_recover_host+0x84c/0xa98 [libsas]
scsi_error_handler+0x140/0x5b0
kthread+0x100/0x12c
ret_from_fork+0x10/0x18
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Jason Yan <yanaijie@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reported-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Darrick J. Wong [Fri, 29 Mar 2019 03:43:38 +0000 (20:43 -0700)]
ocfs2: fix inode bh swapping mixup in ocfs2_reflink_inodes_lock
commit
e6a9467ea14bae8691b0f72c500510c42ea8edb8 upstream.
ocfs2_reflink_inodes_lock() can swap the inode1/inode2 variables so that
we always grab cluster locks in order of increasing inode number.
Unfortunately, we forget to swap the inode record buffer head pointers
when we've done this, which leads to incorrect bookkeepping when we're
trying to make the two inodes have the same refcount tree.
This has the effect of causing filesystem shutdowns if you're trying to
reflink data from inode 100 into inode 97, where inode 100 already has a
refcount tree attached and inode 97 doesn't. The reflink code decides
to copy the refcount tree pointer from 100 to 97, but uses inode 97's
inode record to open the tree root (which it doesn't have) and blows up.
This issue causes filesystem shutdowns and metadata corruption!
Link: http://lkml.kernel.org/r/20190312214910.GK20533@magnolia
Fixes:
29ac8e856cb369 ("ocfs2: implement the VFS clone_range, copy_range, and dedupe_range features")
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Joseph Qi <jiangqi903@gmail.com>
Cc: Mark Fasheh <mfasheh@versity.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <joseph.qi@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tetsuo Handa [Fri, 29 Mar 2019 03:43:30 +0000 (20:43 -0700)]
fs/open.c: allow opening only regular files during execve()
commit
73601ea5b7b18eb234219ae2adf77530f389da79 upstream.
syzbot is hitting lockdep warning [1] due to trying to open a fifo
during an execve() operation. But we don't need to open non regular
files during an execve() operation, for all files which we will need are
the executable file itself and the interpreter programs like /bin/sh and
ld-linux.so.2 .
Since the manpage for execve(2) says that execve() returns EACCES when
the file or a script interpreter is not a regular file, and the manpage
for uselib(2) says that uselib() can return EACCES, and we use
FMODE_EXEC when opening for execve()/uselib(), we can bail out if a non
regular file is requested with FMODE_EXEC set.
Since this deadlock followed by khungtaskd warnings is trivially
reproducible by a local unprivileged user, and syzbot's frequent crash
due to this deadlock defers finding other bugs, let's workaround this
deadlock until we get a chance to find a better solution.
[1] https://syzkaller.appspot.com/bug?id=
b5095bfec44ec84213bac54742a82483aad578ce
Link: http://lkml.kernel.org/r/1552044017-7890-1-git-send-email-penguin-kernel@I-love.SAKURA.ne.jp
Reported-by: syzbot <syzbot+e93a80c1bb7c5c56e522461c149f8bf55eab1b2b@syzkaller.appspotmail.com>
Fixes:
8924feff66f35fe2 ("splice: lift pipe_lock out of splice_to_pipe()")
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Eric Biggers <ebiggers3@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: <stable@vger.kernel.org> [4.9+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fredrik Noring [Wed, 27 Mar 2019 18:12:50 +0000 (19:12 +0100)]
kbuild: modversions: Fix relative CRC byte order interpretation
commit
54a7151b1496cddbb7a83546b7998103e98edc88 upstream.
Fix commit
56067812d5b0 ("kbuild: modversions: add infrastructure for
emitting relative CRCs") where CRCs are interpreted in host byte order
rather than proper kernel byte order. The bug is conditional on
CONFIG_MODULE_REL_CRCS.
For example, when loading a BE module into a BE kernel compiled with a LE
system, the error "disagrees about version of symbol module_layout" is
produced. A message such as "Found checksum
D7FA6856 vs module
5668FAD7"
will be given with debug enabled, which indicates an obvious endian
problem within __kcrctab within the kernel image.
The general solution is to use the macro TO_NATIVE, as is done in
similar cases throughout modpost.c. With this correction it has been
verified that a BE kernel compiled with a LE system accepts BE modules.
This change has also been verified with a LE kernel compiled with a LE
system, in which case TO_NATIVE returns its value unmodified since the
byte orders match. This is by far the common case.
Fixes:
56067812d5b0 ("kbuild: modversions: add infrastructure for emitting relative CRCs")
Signed-off-by: Fredrik Noring <noring@nocrew.org>
Cc: stable@vger.kernel.org
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kailang Yang [Thu, 14 Mar 2019 07:50:59 +0000 (15:50 +0800)]
ALSA: hda/realtek - Add support headset mode for New DELL WYSE NB
commit
da484d00f020af3dd7cfcc6c4b69a7f856832883 upstream.
Enable headset mode support for new WYSE NB platform.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kailang Yang [Thu, 14 Mar 2019 08:22:45 +0000 (16:22 +0800)]
ALSA: hda/realtek - Add support headset mode for DELL WYSE AIO
commit
136824efaab2c095fc911048f7c7ddeda258c965 upstream.
This patch will enable WYSE AIO for Headset mode.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Mon, 25 Mar 2019 09:38:58 +0000 (10:38 +0100)]
ALSA: pcm: Don't suspend stream in unrecoverable PCM state
commit
113ce08109f8e3b091399e7cc32486df1cff48e7 upstream.
Currently PCM core sets each opened stream forcibly to SUSPENDED state
via snd_pcm_suspend_all() call, and the user-space is responsible for
re-triggering the resume manually either via snd_pcm_resume() or
prepare call. The scheme works fine usually, but there are corner
cases where the stream can't be resumed by that call: the streams
still in OPEN state before finishing hw_params. When they are
suspended, user-space cannot perform resume or prepare because they
haven't been set up yet. The only possible recovery is to re-open the
device, which isn't nice at all. Similarly, when a stream is in
DISCONNECTED state, it makes no sense to change it to SUSPENDED
state. Ditto for in SETUP state; which you can re-prepare directly.
So, this patch addresses these issues by filtering the PCM streams to
be suspended by checking the PCM state. When a stream is in either
OPEN, SETUP or DISCONNECTED as well as already SUSPENDED, the suspend
action is skipped.
To be noted, this problem was originally reported for the PCM runtime
PM on HD-audio. And, the runtime PM problem itself was already
addressed (although not intended) by the code refactoring commits
3d21ef0b49f8 ("ALSA: pcm: Suspend streams globally via device type PM
ops") and
17bc4815de58 ("ALSA: pci: Remove superfluous
snd_pcm_suspend*() calls"). These commits eliminated the
snd_pcm_suspend*() calls from the runtime PM suspend callback code
path, hence the racy OPEN state won't appear while runtime PM.
(FWIW, the race window is between snd_pcm_open_substream() and the
first power up in azx_pcm_open().)
Although the runtime PM issue was already "fixed", the same problem is
still present for the system PM, hence this patch is still needed.
And for stable trees, this patch alone should suffice for fixing the
runtime PM problem, too.
Reported-and-tested-by: Jon Hunter <jonathanh@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Fri, 22 Mar 2019 15:00:54 +0000 (16:00 +0100)]
ALSA: pcm: Fix possible OOB access in PCM oss plugins
commit
ca0214ee2802dd47239a4e39fb21c5b00ef61b22 upstream.
The PCM OSS emulation converts and transfers the data on the fly via
"plugins". The data is converted over the dynamically allocated
buffer for each plugin, and recently syzkaller caught OOB in this
flow.
Although the bisection by syzbot pointed out to the commit
65766ee0bf7f ("ALSA: oss: Use kvzalloc() for local buffer
allocations"), this is merely a commit to replace vmalloc() with
kvmalloc(), hence it can't be the cause. The further debug action
revealed that this happens in the case where a slave PCM doesn't
support only the stereo channels while the OSS stream is set up for a
mono channel. Below is a brief explanation:
At each OSS parameter change, the driver sets up the PCM hw_params
again in snd_pcm_oss_change_params_lock(). This is also the place
where plugins are created and local buffers are allocated. The
problem is that the plugins are created before the final hw_params is
determined. Namely, two snd_pcm_hw_param_near() calls for setting the
period size and periods may influence on the final result of channels,
rates, etc, too, while the current code has already created plugins
beforehand with the premature values. So, the plugin believes that
channels=1, while the actual I/O is with channels=2, which makes the
driver reading/writing over the allocated buffer size.
The fix is simply to move the plugin allocation code after the final
hw_params call.
Reported-by: syzbot+d4503ae45b65c5bc1194@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gustavo A. R. Silva [Wed, 20 Mar 2019 23:42:01 +0000 (18:42 -0500)]
ALSA: seq: oss: Fix Spectre v1 vulnerability
commit
c709f14f0616482b67f9fbcb965e1493a03ff30b upstream.
dev is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
sound/core/seq/oss/seq_oss_synth.c:626 snd_seq_oss_synth_make_info() warn: potential spectre issue 'dp->synths' [w] (local cap)
Fix this by sanitizing dev before using it to index dp->synths.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://lore.kernel.org/lkml/
20180423164740.GY17484@dhcp22.suse.cz/
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gustavo A. R. Silva [Wed, 20 Mar 2019 21:15:24 +0000 (16:15 -0500)]
ALSA: rawmidi: Fix potential Spectre v1 vulnerability
commit
2b1d9c8f87235f593826b9cf46ec10247741fff9 upstream.
info->stream is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
sound/core/rawmidi.c:604 __snd_rawmidi_info_select() warn: potential spectre issue 'rmidi->streams' [r] (local cap)
Fix this by sanitizing info->stream before using it to index
rmidi->streams.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://lore.kernel.org/lkml/
20180423164740.GY17484@dhcp22.suse.cz/
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christian Lamparter [Fri, 22 Mar 2019 00:05:02 +0000 (01:05 +0100)]
net: dsa: qca8k: remove leftover phy accessors
commit
1eec7151ae0e134bd42e3f128066b2ff8da21393 upstream.
This belated patch implements Andrew Lunn's request of
"remove the phy_read() and phy_write() functions."
<https://lore.kernel.org/patchwork/comment/902734/>
While seemingly harmless, this causes the switch's user
port PHYs to get registered twice. This is because the
DSA subsystem will create a slave mdio-bus not knowing
that the qca8k_phy_(read|write) accessors operate on
the external mdio-bus. So the same "bus" gets effectively
duplicated.
Cc: stable@vger.kernel.org
Fixes:
6b93fb46480a ("net-next: dsa: add new driver for qca8xxx family")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Olga Kornievskaia [Tue, 19 Mar 2019 16:12:13 +0000 (12:12 -0400)]
NFSv4.1 don't free interrupted slot on open
commit
0cb98abb5bd13b9a636bde603d952d722688b428 upstream.
Allow the async rpc task for finish and update the open state if needed,
then free the slot. Otherwise, the async rpc unable to decode the reply.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Fixes:
ae55e59da0e4 ("pnfs: Don't release the sequence slot...")
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Naveen N. Rao [Fri, 15 Mar 2019 14:51:19 +0000 (20:21 +0530)]
powerpc: bpf: Fix generation of load/store DW instructions
commit
86be36f6502c52ddb4b85938145324fd07332da1 upstream.
Yauheni Kaliuta pointed out that PTR_TO_STACK store/load verifier test
was failing on powerpc64 BE, and rightfully indicated that the PPC_LD()
macro is not masking away the last two bits of the offset per the ISA,
resulting in the generation of 'lwa' instruction instead of the intended
'ld' instruction.
Segher also pointed out that we can't simply mask away the last two bits
as that will result in loading/storing from/to a memory location that
was not intended.
This patch addresses this by using ldx/stdx if the offset is not
word-aligned. We load the offset into a temporary register (TMP_REG_2)
and use that as the index register in a subsequent ldx/stdx. We fix
PPC_LD() macro to mask off the last two bits, but enhance PPC_BPF_LL()
and PPC_BPF_STL() to factor in the offset value and generate the proper
instruction sequence. We also convert all existing users of PPC_LD() and
PPC_STD() to use these macros. All existing uses of these macros have
been audited to ensure that TMP_REG_2 can be clobbered.
Fixes:
156d0e290e96 ("powerpc/ebpf/jit: Implement JIT compiler for extended BPF")
Cc: stable@vger.kernel.org # v4.9+
Reported-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kohji Okuno [Tue, 26 Feb 2019 02:34:13 +0000 (11:34 +0900)]
ARM: imx6q: cpuidle: fix bug that CPU might not wake up at expected time
commit
91740fc8242b4f260cfa4d4536d8551804777fae upstream.
In the current cpuidle implementation for i.MX6q, the CPU that sets
'WAIT_UNCLOCKED' and the CPU that returns to 'WAIT_CLOCKED' are always
the same. While the CPU that sets 'WAIT_UNCLOCKED' is in IDLE state of
"WAIT", if the other CPU wakes up and enters IDLE state of "WFI"
istead of "WAIT", this CPU can not wake up at expired time.
Because, in the case of "WFI", the CPU must be waked up by the local
timer interrupt. But, while 'WAIT_UNCLOCKED' is set, the local timer
is stopped, when all CPUs execute "wfi" instruction. As a result, the
local timer interrupt is not fired.
In this situation, this CPU will wake up by IRQ different from local
timer. (e.g. broacast timer)
So, this fix changes CPU to return to 'WAIT_CLOCKED'.
Signed-off-by: Kohji Okuno <okuno.kohji@jp.panasonic.com>
Fixes:
e5f9dec8ff5f ("ARM: imx6q: support WAIT mode using cpuidle")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrea Righi [Thu, 14 Mar 2019 07:56:28 +0000 (08:56 +0100)]
btrfs: raid56: properly unmap parity page in finish_parity_scrub()
commit
3897b6f0a859288c22fb793fad11ec2327e60fcd upstream.
Parity page is incorrectly unmapped in finish_parity_scrub(), triggering
a reference counter bug on i386, i.e.:
[ 157.662401] kernel BUG at mm/highmem.c:349!
[ 157.666725] invalid opcode: 0000 [#1] SMP PTI
The reason is that kunmap(p_page) was completely left out, so we never
did an unmap for the p_page and the loop unmapping the rbio page was
iterating over the wrong number of stripes: unmapping should be done
with nr_data instead of rbio->real_stripes.
Test case to reproduce the bug:
- create a raid5 btrfs filesystem:
# mkfs.btrfs -m raid5 -d raid5 /dev/sdb /dev/sdc /dev/sdd /dev/sde
- mount it:
# mount /dev/sdb /mnt
- run btrfs scrub in a loop:
# while :; do btrfs scrub start -BR /mnt; done
BugLink: https://bugs.launchpad.net/bugs/1812845
Fixes:
5a6ac9eacb49 ("Btrfs, raid56: support parity scrub on raid56")
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Josef Bacik [Wed, 6 Mar 2019 22:13:04 +0000 (17:13 -0500)]
btrfs: remove WARN_ON in log_dir_items
commit
2cc8334270e281815c3850c3adea363c51f21e0d upstream.
When Filipe added the recursive directory logging stuff in
2f2ff0ee5e430 ("Btrfs: fix metadata inconsistencies after directory
fsync") he specifically didn't take the directory i_mutex for the
children directories that we need to log because of lockdep. This is
generally fine, but can lead to this WARN_ON() tripping if we happen to
run delayed deletion's in between our first search and our second search
of dir_item/dir_indexes for this directory. We expect this to happen,
so the WARN_ON() isn't necessary. Drop the WARN_ON() and add a comment
so we know why this case can happen.
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Filipe Manana [Mon, 4 Mar 2019 14:06:12 +0000 (14:06 +0000)]
Btrfs: fix incorrect file size after shrinking truncate and fsync
commit
bf504110bc8aa05df48b0e5f0aa84bfb81e0574b upstream.
If we do a shrinking truncate against an inode which is already present
in the respective log tree and then rename it, as part of logging the new
name we end up logging an inode item that reflects the old size of the
file (the one which we previously logged) and not the new smaller size.
The decision to preserve the size previously logged was added by commit
1a4bcf470c886b ("Btrfs: fix fsync data loss after adding hard link to
inode") in order to avoid data loss after replaying the log. However that
decision is only needed for the case the logged inode size is smaller then
the current size of the inode, as explained in that commit's change log.
If the current size of the inode is smaller then the previously logged
size, we know a shrinking truncate happened and therefore need to use
that smaller size.
Example to trigger the problem:
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt
$ xfs_io -f -c "pwrite -S 0xab 0 8000" /mnt/foo
$ xfs_io -c "fsync" /mnt/foo
$ xfs_io -c "truncate 3000" /mnt/foo
$ mv /mnt/foo /mnt/bar
$ xfs_io -c "fsync" /mnt/bar
<power failure>
$ mount /dev/sdb /mnt
$ od -t x1 -A d /mnt/bar
0000000 ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab
*
0008000
Once we rename the file, we log its name (and inode item), and because
the inode was already logged before in the current transaction, we log it
with a size of 8000 bytes because that is the size we previously logged
(with the first fsync). As part of the rename, besides logging the inode,
we do also sync the log, which is done since commit
d4682ba03ef618
("Btrfs: sync log after logging new name"), so the next fsync against our
inode is effectively a no-op, since no new changes happened since the
rename operation. Even if did not sync the log during the rename
operation, the same problem (fize size of 8000 bytes instead of 3000
bytes) would be visible after replaying the log if the log ended up
getting synced to disk through some other means, such as for example by
fsyncing some other modified file. In the example above the fsync after
the rename operation is there just because not every filesystem may
guarantee logging/journalling the inode (and syncing the log/journal)
during the rename operation, for example it is needed for f2fs, but not
for ext4 and xfs.
Fix this scenario by, when logging a new name (which is triggered by
rename and link operations), using the current size of the inode instead
of the previously logged inode size.
A test case for fstests follows soon.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202695
CC: stable@vger.kernel.org # 4.4+
Reported-by: Seulbae Kim <seulbae@gatech.edu>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Ellerman [Fri, 29 Mar 2019 11:26:20 +0000 (22:26 +1100)]
powerpc/security: Fix spectre_v2 reporting
commit
92edf8df0ff2ae86cc632eeca0e651fd8431d40d upstream.
When I updated the spectre_v2 reporting to handle software count cache
flush I got the logic wrong when there's no software count cache
enabled at all.
The result is that on systems with the software count cache flush
disabled we print:
Mitigation: Indirect branch cache disabled, Software count cache flush
Which correctly indicates that the count cache is disabled, but
incorrectly says the software count cache flush is enabled.
The root of the problem is that we are trying to handle all
combinations of options. But we know now that we only expect to see
the software count cache flush enabled if the other options are false.
So split the two cases, which simplifies the logic and fixes the bug.
We were also missing a space before "(hardware accelerated)".
The result is we see one of:
Mitigation: Indirect branch serialisation (kernel only)
Mitigation: Indirect branch cache disabled
Mitigation: Software count cache flush
Mitigation: Software count cache flush (hardware accelerated)
Fixes:
ee13cb249fab ("powerpc/64s: Add support for software count cache flush")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christophe Leroy [Fri, 29 Mar 2019 11:26:19 +0000 (22:26 +1100)]
powerpc/fsl: Fix the flush of branch predictor.
commit
27da80719ef132cf8c80eb406d5aeb37dddf78cc upstream.
The commit identified below adds MC_BTB_FLUSH macro only when
CONFIG_PPC_FSL_BOOK3E is defined. This results in the following error
on some configs (seen several times with kisskb randconfig_defconfig)
arch/powerpc/kernel/exceptions-64e.S:576: Error: Unrecognized opcode: `mc_btb_flush'
make[3]: *** [scripts/Makefile.build:367: arch/powerpc/kernel/exceptions-64e.o] Error 1
make[2]: *** [scripts/Makefile.build:492: arch/powerpc/kernel] Error 2
make[1]: *** [Makefile:1043: arch/powerpc] Error 2
make: *** [Makefile:152: sub-make] Error 2
This patch adds a blank definition of MC_BTB_FLUSH for other cases.
Fixes:
10c5e83afd4a ("powerpc/fsl: Flush the branch predictor at each kernel entry (64bit)")
Cc: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Diana Craciun [Fri, 29 Mar 2019 11:26:18 +0000 (22:26 +1100)]
powerpc/fsl: Fixed warning: orphan section `__btb_flush_fixup'
commit
039daac5526932ec731e4499613018d263af8b3e upstream.
Fixed the following build warning:
powerpc-linux-gnu-ld: warning: orphan section `__btb_flush_fixup' from
`arch/powerpc/kernel/head_44x.o' being placed in section
`__btb_flush_fixup'.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Diana Craciun [Fri, 29 Mar 2019 11:26:17 +0000 (22:26 +1100)]
powerpc/fsl: Update Spectre v2 reporting
commit
dfa88658fb0583abb92e062c7a9cd5a5b94f2a46 upstream.
Report branch predictor state flush as a mitigation for
Spectre variant 2.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Diana Craciun [Fri, 29 Mar 2019 11:26:16 +0000 (22:26 +1100)]
powerpc/fsl: Enable runtime patching if nospectre_v2 boot arg is used
commit
3bc8ea8603ae4c1e09aca8de229ad38b8091fcb3 upstream.
If the user choses not to use the mitigations, replace
the code sequence with nops.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Diana Craciun [Fri, 29 Mar 2019 11:26:15 +0000 (22:26 +1100)]
powerpc/fsl: Flush branch predictor when entering KVM
commit
e7aa61f47b23afbec41031bc47ca8d6cb6516abc upstream.
Switching from the guest to host is another place
where the speculative accesses can be exploited.
Flush the branch predictor when entering KVM.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Diana Craciun [Fri, 29 Mar 2019 11:26:14 +0000 (22:26 +1100)]
powerpc/fsl: Flush the branch predictor at each kernel entry (32 bit)
commit
7fef436295bf6c05effe682c8797dfcb0deb112a upstream.
In order to protect against speculation attacks on
indirect branches, the branch predictor is flushed at
kernel entry to protect for the following situations:
- userspace process attacking another userspace process
- userspace process attacking the kernel
Basically when the privillege level change (i.e.the kernel
is entered), the branch predictor state is flushed.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Diana Craciun [Fri, 29 Mar 2019 11:26:13 +0000 (22:26 +1100)]
powerpc/fsl: Flush the branch predictor at each kernel entry (64bit)
commit
10c5e83afd4a3f01712d97d3bb1ae34d5b74a185 upstream.
In order to protect against speculation attacks on
indirect branches, the branch predictor is flushed at
kernel entry to protect for the following situations:
- userspace process attacking another userspace process
- userspace process attacking the kernel
Basically when the privillege level change (i.e. the
kernel is entered), the branch predictor state is flushed.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Diana Craciun [Fri, 29 Mar 2019 11:26:12 +0000 (22:26 +1100)]
powerpc/fsl: Add nospectre_v2 command line argument
commit
f633a8ad636efb5d4bba1a047d4a0f1ef719aa06 upstream.
When the command line argument is present, the Spectre variant 2
mitigations are disabled.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Diana Craciun [Fri, 29 Mar 2019 11:26:11 +0000 (22:26 +1100)]
powerpc/fsl: Emulate SPRN_BUCSR register
commit
98518c4d8728656db349f875fcbbc7c126d4c973 upstream.
In order to flush the branch predictor the guest kernel performs
writes to the BUCSR register which is hypervisor privilleged. However,
the branch predictor is flushed at each KVM entry, so the branch
predictor has been already flushed, so just return as soon as possible
to guest.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
[mpe: Tweak comment formatting]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Diana Craciun [Fri, 29 Mar 2019 11:26:10 +0000 (22:26 +1100)]
powerpc/fsl: Fix spectre_v2 mitigations reporting
commit
7d8bad99ba5a22892f0cad6881289fdc3875a930 upstream.
Currently for CONFIG_PPC_FSL_BOOK3E the spectre_v2 file is incorrect:
$ cat /sys/devices/system/cpu/vulnerabilities/spectre_v2
"Mitigation: Software count cache flush"
Which is wrong. Fix it to report vulnerable for now.
Fixes:
ee13cb249fab ("powerpc/64s: Add support for software count cache flush")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Diana Craciun [Fri, 29 Mar 2019 11:26:09 +0000 (22:26 +1100)]
powerpc/fsl: Add macro to flush the branch predictor
commit
1cbf8990d79ff69da8ad09e8a3df014e1494462b upstream.
The BUCSR register can be used to invalidate the entries in the
branch prediction mechanisms.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Diana Craciun [Fri, 29 Mar 2019 11:26:08 +0000 (22:26 +1100)]
powerpc/fsl: Add infrastructure to fixup branch predictor flush
commit
76a5eaa38b15dda92cd6964248c39b5a6f3a4e9d upstream.
In order to protect against speculation attacks (Spectre
variant 2) on NXP PowerPC platforms, the branch predictor
should be flushed when the privillege level is changed.
This patch is adding the infrastructure to fixup at runtime
the code sections that are performing the branch predictor flush
depending on a boot arg parameter which is added later in a
separate patch.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Ellerman [Fri, 29 Mar 2019 11:26:07 +0000 (22:26 +1100)]
powerpc/powernv: Query firmware for count cache flush settings
commit
99d54754d3d5f896a8f616b0b6520662bc99d66b upstream.
Look for fw-features properties to determine the appropriate settings
for the count cache flush, and then call the generic powerpc code to
set it up based on the security feature flags.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Ellerman [Fri, 29 Mar 2019 11:26:06 +0000 (22:26 +1100)]
powerpc/pseries: Query hypervisor for count cache flush settings
commit
ba72dc171954b782a79d25e0f4b3ed91090c3b1e upstream.
Use the existing hypercall to determine the appropriate settings for
the count cache flush, and then call the generic powerpc code to set
it up based on the security feature flags.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Ellerman [Fri, 29 Mar 2019 11:26:05 +0000 (22:26 +1100)]
powerpc/64s: Add support for software count cache flush
commit
ee13cb249fabdff8b90aaff61add347749280087 upstream.
Some CPU revisions support a mode where the count cache needs to be
flushed by software on context switch. Additionally some revisions may
have a hardware accelerated flush, in which case the software flush
sequence can be shortened.
If we detect the appropriate flag from firmware we patch a branch
into _switch() which takes us to a count cache flush sequence.
That sequence in turn may be patched to return early if we detect that
the CPU supports accelerating the flush sequence in hardware.
Add debugfs support for reporting the state of the flush, as well as
runtime disabling it.
And modify the spectre_v2 sysfs file to report the state of the
software flush.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Ellerman [Fri, 29 Mar 2019 11:26:04 +0000 (22:26 +1100)]
powerpc/64s: Add new security feature flags for count cache flush
commit
dc8c6cce9a26a51fc19961accb978217a3ba8c75 upstream.
Add security feature flags to indicate the need for software to flush
the count cache on context switch, and for the presence of a hardware
assisted count cache flush.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Ellerman [Fri, 29 Mar 2019 11:26:03 +0000 (22:26 +1100)]
powerpc/asm: Add a patch_site macro & helpers for patching instructions
commit
06d0bbc6d0f56dacac3a79900e9a9a0d5972d818 upstream.
Add a macro and some helper C functions for patching single asm
instructions.
The gas macro means we can do something like:
1: nop
patch_site 1b, patch__foo
Which is less visually distracting than defining a GLOBAL symbol at 1,
and also doesn't pollute the symbol table which can confuse eg. perf.
These are obviously similar to our existing feature sections, but are
not automatically patched based on CPU/MMU features, rather they are
designed to be manually patched by C code at some arbitrary point.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Diana Craciun [Fri, 29 Mar 2019 11:26:02 +0000 (22:26 +1100)]
powerpc/fsl: Sanitize the syscall table for NXP PowerPC 32 bit platforms
commit
c28218d4abbf4f2035495334d8bfcba64bda4787 upstream.
Used barrier_nospec to sanitize the syscall table.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Diana Craciun [Fri, 29 Mar 2019 11:26:01 +0000 (22:26 +1100)]
powerpc/fsl: Add barrier_nospec implementation for NXP PowerPC Book3E
commit
ebcd1bfc33c7a90df941df68a6e5d4018c022fba upstream.
Implement the barrier_nospec as a isync;sync instruction sequence.
The implementation uses the infrastructure built for BOOK3S 64.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Diana Craciun [Fri, 29 Mar 2019 11:26:00 +0000 (22:26 +1100)]
powerpc/64: Make meltdown reporting Book3S 64 specific
commit
406d2b6ae3420f5bb2b3db6986dc6f0b6dbb637b upstream.
In a subsequent patch we will enable building security.c for Book3E.
However the NXP platforms are not vulnerable to Meltdown, so make the
Meltdown vulnerability reporting PPC_BOOK3S_64 specific.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Ellerman [Fri, 29 Mar 2019 11:25:59 +0000 (22:25 +1100)]
powerpc/64: Call setup_barrier_nospec() from setup_arch()
commit
af375eefbfb27cbb5b831984e66d724a40d26b5c upstream.
Currently we require platform code to call setup_barrier_nospec(). But
if we add an empty definition for the !CONFIG_PPC_BARRIER_NOSPEC case
then we can call it in setup_arch().
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Ellerman [Fri, 29 Mar 2019 11:25:58 +0000 (22:25 +1100)]
powerpc/64: Add CONFIG_PPC_BARRIER_NOSPEC
commit
179ab1cbf883575c3a585bcfc0f2160f1d22a149 upstream.
Add a config symbol to encode which platforms support the
barrier_nospec speculation barrier. Currently this is just Book3S 64
but we will add Book3E in a future patch.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Diana Craciun [Fri, 29 Mar 2019 11:25:57 +0000 (22:25 +1100)]
powerpc/64: Make stf barrier PPC_BOOK3S_64 specific.
commit
6453b532f2c8856a80381e6b9a1f5ea2f12294df upstream.
NXP Book3E platforms are not vulnerable to speculative store
bypass, so make the mitigations PPC_BOOK3S_64 specific.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Diana Craciun [Fri, 29 Mar 2019 11:25:56 +0000 (22:25 +1100)]
powerpc/64: Disable the speculation barrier from the command line
commit
cf175dc315f90185128fb061dc05b6fbb211aa2f upstream.
The speculation barrier can be disabled from the command line
with the parameter: "nospectre_v1".
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Ellerman [Fri, 29 Mar 2019 11:25:55 +0000 (22:25 +1100)]
powerpc64s: Show ori31 availability in spectre_v1 sysfs file not v2
commit
6d44acae1937b81cf8115ada8958e04f601f3f2e upstream.
When I added the spectre_v2 information in sysfs, I included the
availability of the ori31 speculation barrier.
Although the ori31 barrier can be used to mitigate v2, it's primarily
intended as a spectre v1 mitigation. Spectre v2 is mitigated by
hardware changes.
So rework the sysfs files to show the ori31 information in the
spectre_v1 file, rather than v2.
Currently we display eg:
$ grep . spectre_v*
spectre_v1:Mitigation: __user pointer sanitization
spectre_v2:Mitigation: Indirect branch cache disabled, ori31 speculation barrier enabled
After:
$ grep . spectre_v*
spectre_v1:Mitigation: __user pointer sanitization, ori31 speculation barrier enabled
spectre_v2:Mitigation: Indirect branch cache disabled
Fixes:
d6fbe1c55c55 ("powerpc/64s: Wire up cpu_show_spectre_v2()")
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michal Suchanek [Fri, 29 Mar 2019 11:25:54 +0000 (22:25 +1100)]
powerpc/64s: Enhance the information in cpu_show_spectre_v1()
commit
a377514519b9a20fa1ea9adddbb4129573129cef upstream.
We now have barrier_nospec as mitigation so print it in
cpu_show_spectre_v1() when enabled.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Ellerman [Fri, 29 Mar 2019 11:25:53 +0000 (22:25 +1100)]
powerpc/64: Use barrier_nospec in syscall entry
commit
51973a815c6b46d7b23b68d6af371ad1c9d503ca upstream.
Our syscall entry is done in assembly so patch in an explicit
barrier_nospec.
Based on a patch by Michal Suchanek.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Ellerman [Fri, 29 Mar 2019 11:25:52 +0000 (22:25 +1100)]
powerpc: Use barrier_nospec in copy_from_user()
commit
ddf35cf3764b5a182b178105f57515b42e2634f8 upstream.
Based on the x86 commit doing the same.
See commit
304ec1b05031 ("x86/uaccess: Use __uaccess_begin_nospec()
and uaccess_try_nospec") and
b3bbfb3fb5d2 ("x86: Introduce
__uaccess_begin_nospec() and uaccess_try_nospec") for more detail.
In all cases we are ordering the load from the potentially
user-controlled pointer vs a previous branch based on an access_ok()
check or similar.
Base on a patch from Michal Suchanek.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michal Suchanek [Fri, 29 Mar 2019 11:25:51 +0000 (22:25 +1100)]
powerpc/64s: Enable barrier_nospec based on firmware settings
commit
cb3d6759a93c6d0aea1c10deb6d00e111c29c19c upstream.
Check what firmware told us and enable/disable the barrier_nospec as
appropriate.
We err on the side of enabling the barrier, as it's no-op on older
systems, see the comment for more detail.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michal Suchanek [Fri, 29 Mar 2019 11:25:50 +0000 (22:25 +1100)]
powerpc/64s: Patch barrier_nospec in modules
commit
815069ca57c142eb71d27439bc27f41a433a67b3 upstream.
Note that unlike RFI which is patched only in kernel the nospec state
reflects settings at the time the module was loaded.
Iterating all modules and re-patching every time the settings change
is not implemented.
Based on lwsync patching.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michal Suchanek [Fri, 29 Mar 2019 11:25:49 +0000 (22:25 +1100)]
powerpc/64s: Add support for ori barrier_nospec patching
commit
2eea7f067f495e33b8b116b35b5988ab2b8aec55 upstream.
Based on the RFI patching. This is required to be able to disable the
speculation barrier.
Only one barrier type is supported and it does nothing when the
firmware does not enable it. Also re-patching modules is not supported
So the only meaningful thing that can be done is patching out the
speculation barrier at boot when the user says it is not wanted.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Sat, 16 Mar 2019 20:09:53 +0000 (13:09 -0700)]
tun: add a missing rcu_read_unlock() in error path
commit
9180bb4f046064dfa4541488102703b402bb04e1 upstream.
In my latest patch I missed one rcu_read_unlock(), in case
device is down.
Fixes:
4477138fa0ae ("tun: properly test for IFF_UP")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Fri, 15 Mar 2019 03:19:47 +0000 (20:19 -0700)]
tun: properly test for IFF_UP
[ Upstream commit
4477138fa0ae4e1b699786ef0600863ea6e6c61c ]
Same reasons than the ones explained in commit
4179cb5a4c92
("vxlan: test dev->flags & IFF_UP before calling netif_rx()")
netif_rx_ni() or napi_gro_frags() must be called under a strict contract.
At device dismantle phase, core networking clears IFF_UP
and flush_all_backlogs() is called after rcu grace period
to make sure no incoming packet might be in a cpu backlog
and still referencing the device.
A similar protocol is used for gro layer.
Most drivers call netif_rx() from their interrupt handler,
and since the interrupts are disabled at device dismantle,
netif_rx() does not have to check dev->flags & IFF_UP
Virtual drivers do not have this guarantee, and must
therefore make the check themselves.
Fixes:
1bd4978a88ac ("tun: honor IFF_UP in tun_get_user()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Finn Thain [Sat, 16 Mar 2019 03:21:19 +0000 (14:21 +1100)]
mac8390: Fix mmio access size probe
[ Upstream commit
bb9e5c5bcd76f4474eac3baf643d7a39f7bac7bb ]
The bug that Stan reported is as follows. After a restart, a 16-bit NIC
may be incorrectly identified as a 32-bit NIC and stop working.
mac8390 slot.E: Memory length resource not found, probing
mac8390 slot.E: Farallon EtherMac II-C (type farallon)
mac8390 slot.E: MAC 00:00:c5:30:c2:99, IRQ 61, 32 KB shared memory at 0xfeed0000, 32-bit access.
The bug never arises after a cold start and only intermittently after a
warm start. (I didn't investigate why the bug is intermittent.)
It turns out that memcpy_toio() is deprecated and memcmp_withio() also
has issues. Replacing these calls with mmio accessors fixes the problem.
Reported-and-tested-by: Stan Johnson <userm57@yahoo.com>
Fixes:
2964db0f5904 ("m68k: Mac DP8390 update")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry Bogdanov [Sat, 16 Mar 2019 08:28:18 +0000 (08:28 +0000)]
net: aquantia: fix rx checksum offload for UDP/TCP over IPv6
[ Upstream commit
a7faaa0c5dc7d091cc9f72b870d7edcdd6f43f12 ]
TCP/UDP checksum validity was propagated to skb
only if IP checksum is valid.
But for IPv6 there is no validity as there is no checksum in IPv6.
This patch propagates TCP/UDP checksum validity regardless of IP checksum.
Fixes:
018423e90bee ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xin Long [Mon, 18 Mar 2019 11:47:00 +0000 (19:47 +0800)]
sctp: get sctphdr by offset in sctp_compute_cksum
[ Upstream commit
273160ffc6b993c7c91627f5a84799c66dfe4dee ]
sctp_hdr(skb) only works when skb->transport_header is set properly.
But in Netfilter, skb->transport_header for ipv6 is not guaranteed
to be right value for sctphdr. It would cause to fail to check the
checksum for sctp packets.
So fix it by using offset, which is always right in all places.
v1->v2:
- Fix the changelog.
Fixes:
e6d8b64b34aa ("net: sctp: fix and consolidate SCTP checksumming code")
Reported-by: Li Shuang <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zhiqiang Liu [Sat, 16 Mar 2019 09:02:54 +0000 (17:02 +0800)]
vxlan: Don't call gro_cells_destroy() before device is unregistered
[ Upstream commit
cc4807bb609230d8959fd732b0bf3bd4c2de8eac ]
Commit
ad6c9986bcb62 ("vxlan: Fix GRO cells race condition between
receive and link delete") fixed a race condition for the typical case a vxlan
device is dismantled from the current netns. But if a netns is dismantled,
vxlan_destroy_tunnels() is called to schedule a unregister_netdevice_queue()
of all the vxlan tunnels that are related to this netns.
In vxlan_destroy_tunnels(), gro_cells_destroy() is called and finished before
unregister_netdevice_queue(). This means that the gro_cells_destroy() call is
done too soon, for the same reasons explained in above commit.
So we need to fully respect the RCU rules, and thus must remove the
gro_cells_destroy() call or risk use after-free.
Fixes:
58ce31cca1ff ("vxlan: GRO support at tunnel layer")
Signed-off-by: Suanming.Mou <mousuanming@huawei.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dean Nelson [Tue, 26 Mar 2019 15:53:26 +0000 (11:53 -0400)]
thunderx: eliminate extra calls to put_page() for pages held for recycling
[ Upstream commit
cd35ef91490ad8049dd180bb060aff7ee192eda9 ]
For the non-XDP case, commit
773225388dae15e72790 ("net: thunderx: Optimize
page recycling for XDP") added code to nicvf_free_rbdr() that, when releasing
the additional receive buffer page reference held for recycling, repeatedly
calls put_page() until the page's _refcount goes to zero. Which results in
the page being freed.
This is not okay if the page's _refcount was greater than 1 (in the non-XDP
case), because nicvf_free_rbdr() should not be subtracting more than what
nicvf_alloc_page() had previously added to the page's _refcount, which was
only 1 (in the non-XDP case).
This can arise if a received packet is still being processed and the receive
buffer (i.e., skb->head) has not yet been freed via skb_free_head() when
nicvf_free_rbdr() is spinning through the aforementioned put_page() loop.
If this should occur, when the received packet finishes processing and
skb_free_head() is called, various problems can ensue. Exactly what, depends on
whether the page has already been reallocated or not, anything from "BUG: Bad
page state ... ", to "Unable to handle kernel NULL pointer dereference ..." or
"Unable to handle kernel paging request...".
So this patch changes nicvf_free_rbdr() to only call put_page() once for pages
held for recycling (in the non-XDP case).
Fixes:
773225388dae ("net: thunderx: Optimize page recycling for XDP")
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dean Nelson [Tue, 26 Mar 2019 15:53:19 +0000 (11:53 -0400)]
thunderx: enable page recycling for non-XDP case
[ Upstream commit
b3e208069477588c06f4d5d986164b435bb06e6d ]
Commit
773225388dae15e72790 ("net: thunderx: Optimize page recycling for XDP")
added code to nicvf_alloc_page() that inadvertently disables receive buffer
page recycling for the non-XDP case by always NULL'ng the page pointer.
This patch corrects two if-conditionals to allow for the recycling of non-XDP
mode pages by only setting the page pointer to NULL when the page is not ready
for recycling.
Fixes:
773225388dae ("net: thunderx: Optimize page recycling for XDP")
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Tue, 19 Mar 2019 12:45:35 +0000 (05:45 -0700)]
tcp: do not use ipv6 header for ipv4 flow
[ Upstream commit
89e4130939a20304f4059ab72179da81f5347528 ]
When a dual stack tcp listener accepts an ipv4 flow,
it should not attempt to use an ipv6 header or tcp_v6_iif() helper.
Fixes:
1397ed35f22d ("ipv6: add flowinfo for tcp6 pkt_options for all cases")
Fixes:
df3687ffc665 ("ipv6: add the IPV6_FL_F_REFLECT flag to IPV6_FL_A_GET")
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Herbert Xu [Thu, 21 Mar 2019 01:39:52 +0000 (09:39 +0800)]
rhashtable: Still do rehash when we get EEXIST
[ Upstream commit
408f13ef358aa5ad56dc6230c2c7deb92cf462b1 ]
As it stands if a shrink is delayed because of an outstanding
rehash, we will go into a rescheduling loop without ever doing
the rehash.
This patch fixes this by still carrying out the rehash and then
rescheduling so that we can shrink after the completion of the
rehash should it still be necessary.
The return value of EEXIST captures this case and other cases
(e.g., another thread expanded/rehashed the table at the same
time) where we should still proceed with the rehash.
Fixes:
da20420f83ea ("rhashtable: Add nested tables")
Reported-by: Josh Elsasser <jelsasser@appneta.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Josh Elsasser <jelsasser@appneta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maxime Chevallier [Sat, 16 Mar 2019 13:41:30 +0000 (14:41 +0100)]
packets: Always register packet sk in the same order
[ Upstream commit
a4dc6a49156b1f8d6e17251ffda17c9e6a5db78a ]
When using fanouts with AF_PACKET, the demux functions such as
fanout_demux_cpu will return an index in the fanout socket array, which
corresponds to the selected socket.
The ordering of this array depends on the order the sockets were added
to a given fanout group, so for FANOUT_CPU this means sockets are bound
to cpus in the order they are configured, which is OK.
However, when stopping then restarting the interface these sockets are
bound to, the sockets are reassigned to the fanout group in the reverse
order, due to the fact that they were inserted at the head of the
interface's AF_PACKET socket list.
This means that traffic that was directed to the first socket in the
fanout group is now directed to the last one after an interface restart.
In the case of FANOUT_CPU, traffic from CPU0 will be directed to the
socket that used to receive traffic from the last CPU after an interface
restart.
This commit introduces a helper to add a socket at the tail of a list,
then uses it to register AF_PACKET sockets.
Note that this changes the order in which sockets are listed in /proc and
with sock_diag.
Fixes:
dc99f600698d ("packet: Add fanout support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
YueHaibing [Tue, 19 Mar 2019 02:16:53 +0000 (10:16 +0800)]
net-sysfs: call dev_hold if kobject_init_and_add success
[ Upstream commit
a3e23f719f5c4a38ffb3d30c8d7632a4ed8ccd9e ]
In netdev_queue_add_kobject and rx_queue_add_kobject,
if sysfs_create_group failed, kobject_put will call
netdev_queue_release to decrease dev refcont, however
dev_hold has not be called. So we will see this while
unregistering dev:
unregister_netdevice: waiting for bcsh0 to become free. Usage count = -1
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes:
d0d668371679 ("net: don't decrement kobj reference count on init failure")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aaro Koskinen [Mon, 18 Mar 2019 21:36:08 +0000 (23:36 +0200)]
net: stmmac: fix memory corruption with large MTUs
[ Upstream commit
223a960c01227e4dbcb6f9fa06b47d73bda21274 ]
When using 16K DMA buffers and ring mode, the DES3 refill is not working
correctly as the function is using a bogus pointer for checking the
private data. As a result stale pointers will remain in the RX descriptor
ring, so DMA will now likely overwrite/corrupt some already freed memory.
As simple reproducer, just receive some UDP traffic:
# ifconfig eth0 down; ifconfig eth0 mtu 9000; ifconfig eth0 up
# iperf3 -c 192.168.253.40 -u -b 0 -R
If you didn't crash by now check the RX descriptors to find non-contiguous
RX buffers:
cat /sys/kernel/debug/stmmaceth/eth0/descriptors_status
[...]
1 [0x2be5020]: 0xa3220321 0x9ffc1ffc 0x72d70082 0x130e207e
^^^^^^^^^^^^^^^^^^^^^
2 [0x2be5040]: 0xa3220321 0x9ffc1ffc 0x72998082 0x1311a07e
^^^^^^^^^^^^^^^^^^^^^
A simple ping test will now report bad data:
# ping -s 8200 192.168.253.40
PING 192.168.253.40 (192.168.253.40) 8200(8228) bytes of data.
8208 bytes from 192.168.253.40: icmp_seq=1 ttl=64 time=1.00 ms
wrong data byte #8144 should be 0xd0 but was 0x88
Fix the wrong pointer. Also we must refill DES3 only if the DMA buffer
size is 16K.
Fixes:
54139cf3bb33 ("net: stmmac: adding multiple buffers for rx")
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Fri, 15 Mar 2019 17:41:14 +0000 (10:41 -0700)]
net: rose: fix a possible stack overflow
[ Upstream commit
e5dcc0c3223c45c94100f05f28d8ef814db3d82c ]
rose_write_internal() uses a temp buffer of 100 bytes, but a manual
inspection showed that given arbitrary input, rose_create_facilities()
can fill up to 110 bytes.
Lets use a tailroom of 256 bytes for peace of mind, and remove
the bounce buffer : we can simply allocate a big enough skb
and adjust its length as needed.
syzbot report :
BUG: KASAN: stack-out-of-bounds in memcpy include/linux/string.h:352 [inline]
BUG: KASAN: stack-out-of-bounds in rose_create_facilities net/rose/rose_subr.c:521 [inline]
BUG: KASAN: stack-out-of-bounds in rose_write_internal+0x597/0x15d0 net/rose/rose_subr.c:116
Write of size 7 at addr
ffff88808b1ffbef by task syz-executor.0/24854
CPU: 0 PID: 24854 Comm: syz-executor.0 Not tainted 5.0.0+ #97
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187
kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
check_memory_region_inline mm/kasan/generic.c:185 [inline]
check_memory_region+0x123/0x190 mm/kasan/generic.c:191
memcpy+0x38/0x50 mm/kasan/common.c:131
memcpy include/linux/string.h:352 [inline]
rose_create_facilities net/rose/rose_subr.c:521 [inline]
rose_write_internal+0x597/0x15d0 net/rose/rose_subr.c:116
rose_connect+0x7cb/0x1510 net/rose/af_rose.c:826
__sys_connect+0x266/0x330 net/socket.c:1685
__do_sys_connect net/socket.c:1696 [inline]
__se_sys_connect net/socket.c:1693 [inline]
__x64_sys_connect+0x73/0xb0 net/socket.c:1693
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x458079
Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:
00007f47b8d9dc78 EFLAGS:
00000246 ORIG_RAX:
000000000000002a
RAX:
ffffffffffffffda RBX:
0000000000000003 RCX:
0000000000458079
RDX:
000000000000001c RSI:
0000000020000040 RDI:
0000000000000004
RBP:
000000000073bf00 R08:
0000000000000000 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000246 R12:
00007f47b8d9e6d4
R13:
00000000004be4a4 R14:
00000000004ceca8 R15:
00000000ffffffff
The buggy address belongs to the page:
page:
ffffea00022c7fc0 count:0 mapcount:0 mapping:
0000000000000000 index:0x0
flags: 0x1fffc0000000000()
raw:
01fffc0000000000 0000000000000000 ffffffff022c0101 0000000000000000
raw:
0000000000000000 0000000000000000 00000000ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88808b1ffa80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff88808b1ffb00: 00 00 00 00 00 00 00 00 f1 f1 f1 f1 00 00 00 03
>
ffff88808b1ffb80: f2 f2 00 00 00 00 00 00 00 00 00 00 00 00 04 f3
^
ffff88808b1ffc00: f3 f3 f3 f3 00 00 00 00 00 00 00 00 00 00 00 00
ffff88808b1ffc80: 00 00 00 00 00 00 00 f1 f1 f1 f1 f1 f1 01 f2 01
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christoph Paasch [Tue, 19 Mar 2019 06:14:52 +0000 (23:14 -0700)]
net/packet: Set __GFP_NOWARN upon allocation in alloc_pg_vec
[ Upstream commit
398f0132c14754fcd03c1c4f8e7176d001ce8ea1 ]
Since commit
fc62814d690c ("net/packet: fix 4gb buffer limit due to overflow check")
one can now allocate packet ring buffers >= UINT_MAX. However, syzkaller
found that that triggers a warning:
[ 21.100000] WARNING: CPU: 2 PID: 2075 at mm/page_alloc.c:4584 __alloc_pages_nod0
[ 21.101490] Modules linked in:
[ 21.101921] CPU: 2 PID: 2075 Comm: syz-executor.0 Not tainted 5.0.0 #146
[ 21.102784] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 0.5.1 01/01/2011
[ 21.103887] RIP: 0010:__alloc_pages_nodemask+0x2a0/0x630
[ 21.104640] Code: fe ff ff 65 48 8b 04 25 c0 de 01 00 48 05 90 0f 00 00 41 bd 01 00 00 00 48 89 44 24 48 e9 9c fe 3
[ 21.107121] RSP: 0018:
ffff88805e1cf920 EFLAGS:
00010246
[ 21.107819] RAX:
0000000000000000 RBX:
ffffffff85a488a0 RCX:
0000000000000000
[ 21.108753] RDX:
0000000000000000 RSI:
dffffc0000000000 RDI:
0000000000000000
[ 21.109699] RBP:
1ffff1100bc39f28 R08:
ffffed100bcefb67 R09:
ffffed100bcefb67
[ 21.110646] R10:
0000000000000001 R11:
ffffed100bcefb66 R12:
000000000000000d
[ 21.111623] R13:
0000000000000000 R14:
ffff88805e77d888 R15:
000000000000000d
[ 21.112552] FS:
00007f7c7de05700(0000) GS:
ffff88806d100000(0000) knlGS:
0000000000000000
[ 21.113612] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 21.114405] CR2:
000000000065c000 CR3:
000000005e58e006 CR4:
00000000001606e0
[ 21.115367] Call Trace:
[ 21.115705] ? __alloc_pages_slowpath+0x21c0/0x21c0
[ 21.116362] alloc_pages_current+0xac/0x1e0
[ 21.116923] kmalloc_order+0x18/0x70
[ 21.117393] kmalloc_order_trace+0x18/0x110
[ 21.117949] packet_set_ring+0x9d5/0x1770
[ 21.118524] ? packet_rcv_spkt+0x440/0x440
[ 21.119094] ? lock_downgrade+0x620/0x620
[ 21.119646] ? __might_fault+0x177/0x1b0
[ 21.120177] packet_setsockopt+0x981/0x2940
[ 21.120753] ? __fget+0x2fb/0x4b0
[ 21.121209] ? packet_release+0xab0/0xab0
[ 21.121740] ? sock_has_perm+0x1cd/0x260
[ 21.122297] ? selinux_secmark_relabel_packet+0xd0/0xd0
[ 21.123013] ? __fget+0x324/0x4b0
[ 21.123451] ? selinux_netlbl_socket_setsockopt+0x101/0x320
[ 21.124186] ? selinux_netlbl_sock_rcv_skb+0x3a0/0x3a0
[ 21.124908] ? __lock_acquire+0x529/0x3200
[ 21.125453] ? selinux_socket_setsockopt+0x5d/0x70
[ 21.126075] ? __sys_setsockopt+0x131/0x210
[ 21.126533] ? packet_release+0xab0/0xab0
[ 21.127004] __sys_setsockopt+0x131/0x210
[ 21.127449] ? kernel_accept+0x2f0/0x2f0
[ 21.127911] ? ret_from_fork+0x8/0x50
[ 21.128313] ? do_raw_spin_lock+0x11b/0x280
[ 21.128800] __x64_sys_setsockopt+0xba/0x150
[ 21.129271] ? lockdep_hardirqs_on+0x37f/0x560
[ 21.129769] do_syscall_64+0x9f/0x450
[ 21.130182] entry_SYSCALL_64_after_hwframe+0x49/0xbe
We should allocate with __GFP_NOWARN to handle this.
Cc: Kal Conley <kal.conley@dectris.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Fixes:
fc62814d690c ("net/packet: fix 4gb buffer limit due to overflow check")
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paolo Abeni [Mon, 25 Mar 2019 13:18:06 +0000 (14:18 +0100)]
net: datagram: fix unbounded loop in __skb_try_recv_datagram()
[ Upstream commit
0b91bce1ebfc797ff3de60c8f4a1e6219a8a3187 ]
Christoph reported a stall while peeking datagram with an offset when
busy polling is enabled. __skb_try_recv_datagram() uses as the loop
termination condition 'queue empty'. When peeking, the socket
queue can be not empty, even when no additional packets are received.
Address the issue explicitly checking for receive queue changes,
as currently done by __skb_wait_for_more_packets().
Fixes:
2b5cd0dfa384 ("net: Change return type of sk_busy_loop from bool to void")
Reported-and-tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjorn Helgaas [Mon, 18 Mar 2019 13:51:06 +0000 (08:51 -0500)]
mISDN: hfcpci: Test both vendor & device ID for Digium HFC4S
[ Upstream commit
fae846e2b7124d4b076ef17791c73addf3b26350 ]
The device ID alone does not uniquely identify a device. Test both the
vendor and device ID to make sure we don't mistakenly think some other
vendor's 0xB410 device is a Digium HFC4S. Also, instead of the bare hex
ID, use the same constant (PCI_DEVICE_ID_DIGIUM_HFC4S) used in the device
ID table.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
YueHaibing [Thu, 21 Mar 2019 07:02:50 +0000 (15:02 +0800)]
genetlink: Fix a memory leak on error path
[ Upstream commit
ceabee6c59943bdd5e1da1a6a20dc7ee5f8113a2 ]
In genl_register_family(), when idr_alloc() fails,
we forget to free the memory we possibly allocate for
family->attrbuf.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes:
2ae0f17df1cd ("genetlink: use idr to track families")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Tue, 19 Mar 2019 12:46:18 +0000 (05:46 -0700)]
dccp: do not use ipv6 header for ipv4 flow
[ Upstream commit
e0aa67709f89d08c8d8e5bdd9e0b649df61d0090 ]
When a dual stack dccp listener accepts an ipv4 flow,
it should not attempt to use an ipv6 header or
inet6_iif() helper.
Fixes:
3df80d9320bc ("[DCCP]: Introduce DCCPv6")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bhadram Varka [Fri, 27 Oct 2017 02:52:02 +0000 (08:22 +0530)]
stmmac: copy unicast mac address to MAC registers
[ Upstream commit
a830405ee452ddc4101c3c9334e6fedd42c6b357 ]
Currently stmmac driver not copying the valid ethernet
MAC address to MAC registers. This patch takes care
of updating the MAC register with MAC address.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christoffer Dall [Tue, 3 Jul 2018 15:43:09 +0000 (17:43 +0200)]
video: fbdev: Set pixclock = 0 in goldfishfb
[ Upstream commit
ace6033ec5c356615eaa3582fb1946e9eaff6662 ]
User space Android code identifies pixclock == 0 as a sign for emulation
and will set the frame rate to 60 fps when reading this value, which is
the desired outcome.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marcel Holtmann [Fri, 18 Jan 2019 12:43:19 +0000 (13:43 +0100)]
Bluetooth: Verify that l2cap_get_conf_opt provides large enough buffer
commit
7c9cbd0b5e38a1672fcd137894ace3b042dfbf69 upstream.
The function l2cap_get_conf_opt will return L2CAP_CONF_OPT_SIZE + opt->len
as length value. The opt->len however is in control over the remote user
and can be used by an attacker to gain access beyond the bounds of the
actual packet.
To prevent any potential leak of heap memory, it is enough to check that
the resulting len calculation after calling l2cap_get_conf_opt is not
below zero. A well formed packet will always return >= 0 here and will
end with the length value being zero after the last option has been
parsed. In case of malformed packets messing with the opt->len field the
length value will become negative. If that is the case, then just abort
and ignore the option.
In case an attacker uses a too short opt->len value, then garbage will
be parsed, but that is protected by the unknown option handling and also
the option parameter size checks.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marcel Holtmann [Fri, 18 Jan 2019 11:56:20 +0000 (12:56 +0100)]
Bluetooth: Check L2CAP option sizes returned from l2cap_get_conf_opt
commit
af3d5d1c87664a4f150fcf3534c6567cb19909b0 upstream.
When doing option parsing for standard type values of 1, 2 or 4 octets,
the value is converted directly into a variable instead of a pointer. To
avoid being tricked into being a pointer, check that for these option
types that sizes actually match. In L2CAP every option is fixed size and
thus it is prudent anyway to ensure that the remote side sends us the
right option size along with option paramters.
If the option size is not matching the option type, then that option is
silently ignored. It is a protocol violation and instead of trying to
give the remote attacker any further hints just pretend that option is
not present and proceed with the default values. Implementation
following the specification and its qualification procedures will always
use the correct size and thus not being impacted here.
To keep the code readable and consistent accross all options, a few
cosmetic changes were also required.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Wed, 27 Mar 2019 05:13:56 +0000 (14:13 +0900)]
Linux 4.14.109
projects / GitHub / LineageOS / android_kernel_motorola_exynos9610.git / log