qlcnic: fix interface attach sequence

Interface should be visible even if resource allocation fails.
netif_device_attach should be called for every netif_device_detach.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: add driver debug support

Add debug print in driver, can be tuned by ethtool msg level
callback.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: use IDC defined timeout value

o USE/Read IDC defined timeout value from ROM.
o While resetting chip, don't wait for other pci-func to respond,
  more than reset_ack_timeo seconds,

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: fix onchip memory access

Fix incorrect offset calculation and remove unnecessary remap
of the region in bar 0 to access onchip memory.

This was leading to read incorrect values by debug tools.

Signed-off-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: update oncard memory size check

All QLogic converged NICs have 128-bit 128MB on card memory.
Fix the limit check from 64MB to 128MB and remove unnecessary
64-bit read/write checks.

Signed-off-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: handle queue manager access

Check the access by tools for hardware queue engine and handle it
separately than other block registers, otherwise incorrect data
is returned.

Signed-off-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: fix fw load from file

Rarely: Fw file size can be unaligned to 8.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

phylib: Add module table to all existing phy drivers

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

phylib: Support phy module autoloading

We don't use the normal hotplug mechanism because it doesn't work. It will
load the module some time after the device appears, but that's not good
enough for us -- we need the driver loaded _immediately_ because otherwise
the NIC driver may just abort and then the phy 'device' goes away.

[bwh: s/phy/mdio/ in module alias, kerneldoc for struct mdio_device_id]

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: illegal_highdma() fix

Followup to commit 5acbbd428db47b12f137a8a2aa96b3c0a96b744e
(net: change illegal_highdma to use dma_mask)

If dev->dev.parent is NULL, we should not try to dereference it.

Dont force inline illegal_highdma() as its pretty big now.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

be2net: Adding PCI SRIOV support

- Patch adds support to enable PCI SRIOV in the driver and changes to handle initialization of PCI virtual functions.
- Function handler to change mac addresses for VF from its corresponding PF.

Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/pcmcia/3c589_cs: using netdev_info and friends where appropriate

Signed-off-by: Alexander Kurz <linux@kbdbabel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

netdev/fec.c: add phylib supporting to enable carrier detection (v2)

BugLink: http://bugs.launchpad.net/bugs/457878
v2:
 - remove duplicated phy_speed caculation
 - fix the phy_speed caculation according to the DataSheet

v1:
 - removed old MII phy control code
 - add phylib supporting
 - add ethtool interface to make user space NetworkManager works

Tested on Freescale i.MX51 Babbage board.

This patch is based on a patch from Frederic Rodo <fred.rodo@gmail.com>

Cc: Frederic Rodo <fred.rodo@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Acked-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: change illegal_highdma to use dma_mask

Robert Hancock pointed out two problems about NETIF_F_HIGHDMA:

-Many drivers only set the flag when they detect they can use 64-bit DMA,
since otherwise they could receive DMA addresses that they can't handle
(which on platforms without IOMMU/SWIOTLB support is fatal). This means that if
64-bit support isn't available, even buffers located below 4GB will get copied
unnecessarily.

-Some drivers set the flag even though they can't actually handle 64-bit DMA,
which would mean that on platforms without IOMMU/SWIOTLB they would get a DMA
mapping error if the memory they received happened to be located above 4GB.

http://lkml.org/lkml/2010/3/3/530

We can use the dma_mask if we need bouncing or not here. Then we can
safely fix drivers that misuse NETIF_F_HIGHDMA.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Added GRO support

Adding GRO support on top of the HW LRO (TPA) support –
there is no measurable performance drawback of adding GRO
on top of it, and it allows better performance when LRO (TPA)
is turned off for virtualization or bridging.

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

flow: structurize flow cache

Group all per-cpu data to one structure instead of having many
globals. Also prepare the internals so that we can have multiple
instances of the flow cache if needed.

Only the kmem_cache is left as a global as all flow caches share
the same element size, and benefit from using a common cache.

Signed-off-by: Timo Teras <timo.teras@iki.fi>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

xfrm: remove policy lock when accessing policy->walk.dead

All of the code considers ->dead as a hint that the cached policy
needs to get refreshed. The read side can just drop the read lock
without any side effects.

The write side needs to make sure that it's written only exactly
once. Only possible race is at xfrm_policy_kill(). This is fixed
by checking result of __xfrm_policy_unlink() when needed. It will
always succeed if the policy object is looked up from the hash
list (so some checks are removed), but it needs to be checked if
we are trying to unlink policy via a reference (appropriate
checks added).

Since policy->walk.dead is written exactly once, it no longer
needs to be protected with a write lock.

Signed-off-by: Timo Teras <timo.teras@iki.fi>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

xfrm_user: verify policy direction at XFRM_MSG_POLEXPIRE handler

Add missing check for policy direction verification. This is
especially important since without this xfrm_user may end up
deleting per-socket policy which is not allowed.

Signed-off-by: Timo Teras <timo.teras@iki.fi>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

xfrm: Remove xfrm_state_genid

The xfrm state genid only needs to be matched against the copy
saved in xfrm_dst.  So we don't need a global genid at all.  In
fact, we don't even need to initialise it.

Based on observation by Timo Teräs.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6 fib: Make rt6_info{} more cache-line aware.

The head element of rt6_info{} is dst_entry{}, and
IPv6 specific elements follow.

Because elements at the end of dst_entry{} are frequently
updated, it is not good to put frequently-used static
elements, such as rt6i_idev, rt6i_dst or rt6i_flags in the
same cache line.

On the other hand, fib6_table, rt6i_node or rt6i_gateway are
rarely used, so it is okay to stay in the same cache line.

Let's rearrange rt6_info{}.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

rps: keep the old behavior on SMP without rps

keep the old behavior on SMP without rps

RPS introduces a lock operation to per cpu variable input_pkt_queue on
SMP whenever rps is enabled or not. On SMP without RPS, this lock isn't
needed at all.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
----
net/core/dev.c | 42 ++++++++++++++++++++++++++++--------------
1 file changed, 28 insertions(+), 14 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: Fix rtl8169_rx_interrupt()

In case a reset is performed, rtl8169_rx_interrupt() is called from
process context instead of softirq context. Special care must be taken
to call appropriate network core services (netif_rx() instead of
netif_receive_skb()). VLAN handling also corrected.

Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Diagnosed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

gen_estimator: deadlock fix

One of my test machine got a deadlock during "tc" sessions,
adding/deleting classes & filters, using traffic estimators.

After some analysis, I believe we have a potential use after free case
in est_timer() :

spin_lock(e->stats_lock); << HERE >>
read_lock(&est_lock);
if (e->bstats == NULL)   << TEST >>
goto skip;

Test is done a bit late, because after estimator is killed, and before
rcu grace period elapsed, we might already have freed/reuse memory where
e->stats_locks points to (some qdisc->q.lock)

A possible fix is to respect a rcu grace period at Qdisc dismantle time.

On 64bit, sizeof(struct Qdisc) is exactly 192 bytes. Adding 16 bytes to
it (for struct rcu_head) is a problem because it might change
performance, given QDISC_ALIGNTO is 32 bytes.

This is why I also change QDISC_ALIGNTO to 64 bytes, to satisfy most
current alignment requirements.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: remove redundant verification code

The check if error signaling is wanted (inet->recverr != 0) is done by
the caller: raw.c:raw_err() and udp.c:__udp4_lib_err(), so there is no
need to check this condition again.

Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

acenic: use the dma state API instead of the pci equivalents

The DMA API is preferred.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

acenic: fix the misusage of zero dma address

acenic wrongly assumes that zero is an invalid dma address (calls
dma_unmap_page for only non zero dma addresses). Zero is a valid dma
address on some architectures. The dma length can be used here.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

net-caif: using kmalloc/kfree requires the include of slab.h

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: eliminate useless code

Remove duplicate declaration of symbol: struct hlist_node *node was
already declared, the seconds declaration shadows the first one.

CC: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: define needless global scoped variable static

struct _zone *tipc_zones has local scope level and
should defined with the correct scoping.

CC: Per Liden <per.liden@nospam.ericsson.com>
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: remove redundant code

eth_type_trans(skb, netdev) does the "skb->dev = netdev;"
initialization, we can remove it from various network drivers.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add hotplug support to mcp251x driver

Chip model can now be selected directly by matching the modalias name
(instead of filling the .model field in platform_data), and allows the
module to be auto-loaded. Previous behaviour is of course still supported.

Convert the two in-tree users to this feature (icontrol & zeus).
Tested on an Zeus platform (mcp2515).

Signed-off-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Christian Pellegrin <chripell@fsfe.org>
Cc: Edwin Peer <epeer@tmtservices.co.za>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fix net/core/dst.c coding style error and warnings

Fix coding style errors and warnings output while running checkpatch.pl
on the file net/core/dst.c.

Signed-off-by: chavey <chavey@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netdev: ethtool RXHASH flag

This adds ethtool and device feature flag to allow control
of receive hashing offload.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: add per-packet timestamping

This patch adds support for per-packet timestamping for the
82580 adapter. The rx timestamp code is also pulled out of the
inlined rx hotpath and instead moved to a seperate function.

This version adds a comment explaining the per-packet timestamping
code added to igb_hwtstamp_ioctl().

Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MAINTAINERS: ipg: Jesse Huang's email address bounces

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ipg: Remove invalid IPG_DDEBUG_MSG uses, neaten

Some no longer valid IPG_DDEBUG_MSG uses are removed
Validate IPG_DDEBUG_MSG arguments when not #defined
Neaten #defines
marco/macro typo correction

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6 fib: Use "Sweezle" to optimize addr_bit_test().

addr_bit_test() is used in various places in IPv6 routing table
subsystem.  It checks if the given fn_bit is set,
where fn_bit counts bits from MSB in words in network-order.

 fn_bit        :   0 .... 31 32 .... 64 65 .... 95 96 ....127

fn_bit >> 5 gives offset of word, and (~fn_bit & 0x1f) gives
count from LSB in the network-endian word in question.

 fn_bit >> 5   :       0          1          2          3
 ~fn_bit & 0x1f:  31 ....  0 31 ....  0 31 ....  0 31 ....  0

Thus, the mask was generated as htonl(1 << (~fn_bit & 0x1f)).
This can be optimized by "sweezle" (See include/asm-generic/bitops/le.h).

In little-endian,
  htonl(1 << bit) = 1 << (bit ^ BITOP_BE32_SWIZZLE)
where
  BITOP_BE32_SWIZZLE is (0x1f & ~7)
So,
  htonl(1 << (~fn_bit & 0x1f)) = 1 << ((~fn_bit & 0x1f) ^ (0x1f & ~7))
                               = 1 << ((~fn_bit ^ ~7) & 0x1f)
                               = 1 << ((~fn_bit ^ BITOP_BE32_SWIZZLE) & 0x1f)

In big-endian, BITOP_BE32_SWIZZLE is equal to 0.
  1 << ((~fn_bit ^ BITOP_BE32_SWIZZLE) & 0x1f)
                               = 1 << ((~fn_bit) & 0x1f)
                               = htonl(1 << (~fn_bit & 0x1f))

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: Use ipv6_addr_diff() in sctp_v6_addr_match_len().

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Use __fls() instead of fls() in __ipv6_addr_diff().

Because we have ensured that the argument is non-zero,
it is better to use __fls() and generate better code.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: typo corrections

Here are the other miscellaneous corrections
done by an earlier larger suggested patch now
made unnecessary by a less invasive change.

Correct a few missing newlines from logging
messages and a typo fix.  Fix speed/duplex
logging message.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: update hw_debug macro to make use of netdev_dbg call

This change updates the igb driver to make use of the netdev_dbg function
macros now provided in netdevice.h

This is meant to be provided as an alternative to the patch provided by
Joe Perches.

It also removes igb_get_time_str since I found that it is unused code that
is no longer used even in debug.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net_sched: minor netns related cleanup

These changes were suggested by Alexey Dobriyan <adobriyan@gmail.com>:

  - psched_show() does not use any private data so just pass NULL to
    psched_open()

  - remove unnecessary return statement

Signed-off-by: Tom Goff <thomas.goff@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sky2: avoid duplicate link up on Optima chip

The Optima version has feature to detect link quickly without PHY interrupt,
but it causes duplicate link up events.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sky2: add XL revisions

Add definitions for Yukon XL revisions.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sky2: support Yukon EC_U rev B1 and later

Need to change logic to support later versions of Yukon 2 EC_U chip.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net-caif-driver: add CAIF serial driver (ldisc)

Add CAIF Serial driver. This driver is implemented as a line discipline.

caif_serial uses the following module parameters:
ser_use_stx - specifies if STart of frame eXtension is in use.
ser_loop    - sets the interface in loopback mode.

Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net-caif: add CAIF documentation

Documentation of the CAIF Protocol.

Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net-caif: add CAIF Kconfig and Makefiles

Kconfig and Makefiles with options for:
CAIF:        Including caif
CAIF_DEBUG:  CAIF Debug
CAIF_NETDEV: CAIF Network Device for GPRS Contexts

Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net-caif: add CAIF netdevice

Adding GPRS Net Device for PDP Contexts.
The device can be managed by RTNL as defined in if_caif.h.

Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net-caif: add CAIF socket implementation

Implementation of CAIF sockets for protocol and address family
PF_CAIF and AF_CAIF.
CAIF socket is connection oriented implementing SOCK_SEQPACKET
and SOCK_STREAM interface with supporting blocking and non-blocking mode.

Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net-caif: add CAIF device registration functionality

Registration and deregistration of CAIF Link Layer.

Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net-caif: add CAIF generic caif support functions

Support functions for the caif protocol stack:
cfcnfg.c        - CAIF Configuration Module used for
                  adding and removing drivers and connection
cfpkt_skbuff.c  - CAIF Packet layer (SKB helper functions)

Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net-caif: add CAIF core protocol stack

CAIF generic protocol implementation. This layer is
somewhat generic in order to be able to use and test it outside
the Linux Kernel.

cfctrl.c     - CAIF control protocol layer
cfdbgl.c     - CAIF debug protocol layer
cfdgml.c     - CAIF datagram protocol layer
cffrml.c     - CAIF framing protocol layer
cfmuxl.c     - CAIF mux protocol layer
cfrfml.c     - CAIF remote file manager protocol layer
cfserl.c     - CAIF serial (fragmentation) protocol layer
cfsrvl.c     - CAIF generic service layer functions
cfutill.c    - CAIF utility protocol layer
cfveil.c     - CAIF AT protocol layer
cfvidl.c     - CAIF video protocol layer

Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net-caif: add CAIF Link layer device header files

Header files for CAIF Link layer net-device,
and link-layer registration.

Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net-caif: add CAIF core protocol stack header files

Add include files for the CAIF Core protocol stack.

caif_layer.h - Defines the structure of the CAIF protocol layers
cfcnfg.h     - CAIF Configuration Module for services and link layers
cfctrl.h     - CAIF Control Protocol Layer
cffrml.h     - CAIF Framing Layer
cfmuxl.h     - CAIF Muxing Layer
cfpkt.h      - CAIF Packet layer (skb helper functions)
cfserl.h     - CAIF Serial Layer
cfsrvl.h     - CAIF Service Layer

Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net-caif: add CAIF socket and configuration headers

Add CAIF types for Socket Address, Socket Options,
and configuration parameters for the GPRS IP network interface.

Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net-caif: add CAIF protocol definitions

Add CAIF definitions to existing header files.
Files: if_arp.h, if_ether.h, socket.h.
Types: ARPHRD_CAIF, ETH_P_CAIF, AF_CAIF, PF_CAIF, SOL_CAIF, N_CAIF

Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

virtio_net: missing sg_init_table

Add missing sg_init_table for sg_set_buf in virtio_net which
induced in defer skb patch.

Reported-by: Thomas Müller <thomas@mathtm.de>
Tested-by: Thomas Müller <thomas@mathtm.de>
Signed-off-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vxge: Updating Maintainer list of S2IO 10GbE drivers (xframe / vxge).

- updating Maintainer list of S2IO 10GbE drivers (xframe / vxge).

Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vxge: Version update.

- Version update

Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vxge: Set function-0 as the privilaged function for normal function.

-  For Normal function (MR-IOV disabled, SR-IOV disabled) Function-0 is the
   privilaged function.

Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vxge: Fixed MSIX interrupt configuration.

- Fixed MSIX interrupt configuration to support non contiguous vpaths in
  functions. Four msi-x vectors are reserved per vpath internal to the chip.
  In all, there are 68 msi-x vectors for the 17 vpaths in the chip. In the
  multi function configurations, non-contiguous vpaths are configured to
  represent a function. For instance vpaths 0 and 8 can be configured to
  represent function zero.

- If pci_enable_msix fails for the requested vectors, try with a lesser number
  vectors by reducing the vpath count.

Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vxge: Fixed "ethtool -d" prints.

- Fixed "ethtool -d" prints
- reg_space pointer was getting over written, updating it correctly.

Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vxge: Align the memory only if it is misaligned.

- Align the memory only if it is misaligned.

Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vxge: Fix starvation of receive ring controller when blasted by short packets.

- Fix starvation of receive ring controller when blasted by short packets. This was because the driver was posting 64 rxds initially while the ring controller
was expecting to read 256 replenished rxds. While the driver was coming up,
the internal rxd memory filled up the 64 buffers provided and the ring
controller was left waiting for the remaining 192 rxds to complete the write
back of completed rxds to the host and generation of an interrupt.

Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vxge: Fix a receive stall due to driver being out of synch with chip.

- Fix a receive stall due to driver being out of synch with chip. In a corner
case scenario the adapter's ring controller may return a RxD with transfer code
of 0xC, while the host ownership bit is still set to the adapter. The driver
needs to assume that this case where (host_ownership == 1 or adapter) and
(transfer_code == 0xC) is valid, that is, this RxD has been returned by the
receive ring controller but no frame data is associated with the rxd.

- Restore the transfer code field of each newly replenished RxD to 0x0.

- Code cleanup. Removed usage of magic numbers.

Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next-2.6

netxen: fix interrupt for NX2031

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
For NX2031, msix is supported from fw version > 3.4.336.
This fw version check should take flash fw in consider instead of
running fw or fw from file.
Signed-off-by: David S. Miller <davem@davemloft.net>

netxen: fix fw load from file

Rarely: Fw file size can be unaligned to 8.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netxen: validate unified romimage

Signed-off-by: Rajesh K Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Validate all sections of unified romimage, before accessing them,
  to avoid seg fault.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netxen: fix corner cases of firmware recovery

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
o DEV_NEED_RESET state was not handled during fw intialization phase.
o nx_decr_dev_ref_cnt() can return error, if fail to grab pcie seamphore.
Signed-off-by: David S. Miller <davem@davemloft.net>

netxen: fix tx csum status

Kernel default tx csum function (ethtool_op_get_tx_csum) doesn't show
correct csum status. It takes various FLAGS (NETIF_F_ALL_CSUM) in account
to show tx csum status, which driver doesn't set while disabling tx csum.

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rps: fix net-sysfs build for !CONFIG_RPS

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: __netif_receive_skb should be static

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

decnet: Remove unused FIB metric macros.

Unlike the ipv4 side, these are completely unused.

Signed-off-by: David S. Miller <davem@davemloft.net>

net: increase preallocated size of nlmsg to accomodate for IFLA_STATS64

When more data is stuffed into an nlmsg than initially projected, an
extra allocation needs to be done. Reserve enough for IFLA_STATS64 so
that this does not to needlessy happen.

Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fix unaligned access in IFLA_STATS64

Tony Luck observes that the original IFLA_STATS64 submission causes
unaligned accesses. This is because nla_data() returns a pointer to a
memory region that is only aligned to 32 bits. Do some memcpying to
workaround this.

Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Use pr_<level> and netdev_<level>

As an alternative to a quite large patch previously submitted by Joe
Perches to make use of kernel logging API, this patch is much less
intrusive.

Convert e_<level> to netdev_<level>
Use #define pr_fmt
Convert a few printks to pr_<level>

Cc: Joe Perches <joe@perches.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink: use the appropriate namespace pid

This was included in OpenVZ kernels but wasn't integrated upstream.
>From git://git.openvz.org/pub/linux-2.6.24-openvz:

commit 5c69402f18adf7276352e051ece2cf31feefab02
Author: Alexey Dobriyan <adobriyan@openvz.org>
Date:   Mon Dec 24 14:37:45 2007 +0300

    netlink: fixup ->tgid to work in multiple PID namespaces

Signed-off-by: Tom Goff <thomas.goff@boeing.com>
Acked-by: Alexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbevf: convert to use netdev_for_each_mc_addr

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: convert to use netdev_for_each_mc_addr

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Fix result generation in ipv6_get_ifaddr().

Finishing naturally from hlist_for_each_entry(x, ...) does not result
in 'x' being NULL.

Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Preserve pervious behavior in ipv6_link_dev_addr().

Use list_add_tail() to get the behavior we had before
the list_head conversion for ipv6 address lists.

Signed-off-by: David S. Miller <davem@davemloft.net>

rps: add CONFIG_RPS

RPS currently depends on SMP and SYSFS

Adding a CONFIG_RPS makes sense in case this requirement changes in the
future. This patch saves about 1500 bytes of kernel text in case SMP is
on but SYSFS is off.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

iwlwifi: fix build error for CONFIG_IWLAGN=n

drivers/net/wireless/iwlwifi/iwl-rx.c: In function 'iwl_good_ack_health':
drivers/net/wireless/iwlwifi/iwl-rx.c:647: error: 'struct iwl_priv' has no member named '_agn'

Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net/various: remove trailing space in messages

Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/intel: remove trailing space in messages

Includes one minor indentation fix to placate checkpatch.

Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: David S. Miller <davem@davemloft.net>

net/tulip: remove trailing space in messages

Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/tokenring: remove trailing space in messages

Trailing spaces in files in /proc for lanstreamer.c and olympic.c
have been left as they are.

Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/smc91xx: remove trailing space in messages

Includes a few whitespace fixes to placate checkpatch.

Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/ps3_gelic: remove trailing space in messages

ps3_gelic_wireless.c: also remove a stray "p" after a newline.

Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@ozlabs.org
Signed-off-by: David S. Miller <davem@davemloft.net>

net/irda: remove trailing space in messages

Includes a minor consistency improvement between two related
debug messages.

Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: remove trailing space in messages

Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: Per Liden <per.liden@ericsson.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: remove trailing space in messages

Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>

rds: cleanup: remove unneeded variable

We never use "sk" so this patch removes it.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

wimax: remove unneeded variable

We never actually use "dev" so I removed it.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

llc: cleanup: remove dead code from llc_init()

We don't need "dev" any more after:
a5a04819c5740cb1aa217af2cc8f5ef26f33d744
[LLC]: station source mac address

Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mac80211: remove unneed variable from ieee80211_tx_pending()

We don't need "sdata" any more after:
d84f323477260e773d5317ad7cbe50f76115cb47
mac80211: remove dev_hold/put calls

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: Improve connection quality maintenance docs in nl80211.h

In nl80211.h, be a little more elaborate in the docs for the definitions
NL80211_ATTR_CQM_RSSI_THOLD and NL80211_ATTR_CQM_RSSI_HYST.

Reported-by: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Add support for connection quality monitoring

Add support for the set_cqm_config op. This op function configures the
requested connection quality monitor rssi threshold and rssi hysteresis
values to the hardware  if the hardware supports
IEEE80211_HW_SUPPORTS_CQM.

For unsupported hardware, currently -EOPNOTSUPP is returned, so the mac80211
is currently not doing connection quality monitoring on the host. This could be
added later, if needed.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>