scsi: qla2xxx: Remove potential macro parameter side-effect in ql_dump_regs()

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Print correct mailbox registers in failed summary

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix task mgmt handling for NPIV

Fix task management response for NPIV Target mode.
Current code uses the wrong vp index.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Allow SNS fabric login to be retried

If SNS fabric login fails, set loop resync flag to retry via dpc.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add timeout ability to wait_for_sess_deletion().

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Move logging default mask to execute once only.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Use sp->free instead of hard coded call.

Calling sp->free() ensures the context-correct free routine is called.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Prevent sp->free null/uninitialized pointer dereference.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add ability to autodetect SFP type

SFP can come in 2 formats: short range/SR and long range/LR.  For LR,
user the can increase the number of Buffer to Buffer credits between end
points via Cavium's command line tool.  By default, FW uses a lower BB
Credit value optimized for SR.  This patch will read the SFP for each
link up event and during chip reset sequence. If the SFP type and
setting are mismatch, then the chip is reset 1 time to use the
appropriate setting.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Use fabric name for Get Port Speed command

The Get Port Speed switch command needs the fabric port name of the
remote device.  Current code uses the registered WWPN.

Fixes: 726b85487067d ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Change ha->wq max_active value to default

Update ha->wq max_active from 1 to default. MQ interrupts are queued up
via this work queue. This allows interrupts to be process in parrallel,
instead of serialized by the work queue.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Remove extra register read

Remove extra register read for each interrupt for performance
improvement.

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix NPIV host enable after chip reset

For NPIV ports, call configure_hba() so that NPIV ports can proceed to
loop initialization.

Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Use BIT_6 to acquire FAWWPN from switch

If FA-WWPN feature disabled on the switch side and enabled for the
adapter, then driver would update the port name with switch port name.

This patch fixes issue by checking correct BIT flag to validate.

Fixes: 41dc529a4602 ("qla2xxx: Improve RSCN handling in driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix system panic due to pointer access problem

[ 1013.772926] BUG: unable to handle kernel paging request at 0000000300000020
[ 1013.772950] IP: qla24xx_els_ct_entry.isra.17+0x78/0x2a0 [qla2xxx]
[ 1013.772951] PGD 0
[ 1013.772952] P4D 0
[ 1013.772952]
[ 1013.772953] Oops: 0000 [#1] SMP
[ 1013.772955] Modules linked in: qla2xxx(+) scsi_transport_fc nvme_fc
nvme_fabrics nvme_core netconsole configfs af_packet iscsi_ibft
iscsi_boot_sysfs xfs intel_rapl sb_edac libcrc32c x86_pkg_temp_thermal
intel_powerclamp coretemp mgag200 kvm_intel ttm kvm drm_kms_helper
ipmi_ssif irqbypass tg3 drm fb_sys_fops crct10dif_pclmul syscopyarea
crc32_pclmul ghash_clmulni_intel ptp pcbc sysfillrect pps_core
aesni_intel joydev aes_x86_64 sysimgblt crypto_simd iTCO_wdt libphy
iTCO_vendor_support i2c_algo_bit glue_helper ipmi_si lpc_ich hpwdt
ioatdma cryptd ipmi_devintf pcspkr mfd_core pcc_cpufreq ipmi_msghandler
hpilo thermal dca button shpchp btrfs xor raid6_pq hid_generic usbhid
sr_mod cdrom sd_mod ata_generic crc32c_intel serio_raw ata_piix ahci
libahci uhci_hcd ehci_pci ehci_hcd libata usbcore hpsa scsi_transport_sas
[ 1013.772994]  sg scsi_mod autofs4
[ 1013.772998] CPU: 0 PID: 374 Comm: systemd-journal Not tainted 4.13.0-rc1-2-default #2
[ 1013.772999] Hardware name: HP ProLiant DL380p Gen8, BIOS P70 07/15/2012
[ 1013.773000] task: ffff88082c188380 task.stack: ffffc90004d7c000
[ 1013.773011] RIP: 0010:qla24xx_els_ct_entry.isra.17+0x78/0x2a0 [qla2xxx]
[ 1013.773012] RSP: 0000:ffff88042f603d90 EFLAGS: 00010082
[ 1013.773013] RAX: ffff88039f723ac8 RBX: ffff88039f723ac8 RCX: ffff8803a2e18010
[ 1013.773014] RDX: ffff88039f723ac0 RSI: ffff88042f603dc4 RDI: ffff88041b6787c0
[ 1013.773015] RBP: ffff88042f603e00 R08: 0000000000000002 R09: 000000000000000d
[ 1013.773016] R10: 0000000000000002 R11: 0000000000000000 R12: ffff8803a2e80080
[ 1013.773016] R13: ffff88041b6787c0 R14: 0000000300000000 R15: 0000000000000102
[ 1013.773018] FS:  00007fa2e0a73880(0000) GS:ffff88042f600000(0000) knlGS:0000000000000000
[ 1013.773019] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1013.773020] CR2: 0000000300000020 CR3: 000000042cd7e000 CR4: 00000000000406f0
[ 1013.773021] Call Trace:
[ 1013.773022]  <IRQ>
[ 1013.773026]  ? consume_skb+0x34/0xa0
[ 1013.773040]  qla24xx_process_response_queue+0x319/0x700 [qla2xxx]
[ 1013.773050]  qla24xx_msix_rsp_q+0x7b/0xd0 [qla2xxx]
[ 1013.773054]  __handle_irq_event_percpu+0x3c/0x1b0
[ 1013.773056]  handle_irq_event_percpu+0x23/0x60
[ 1013.773057]  handle_irq_event+0x42/0x70
[ 1013.773059]  handle_edge_irq+0x8f/0x190
[ 1013.773062]  handle_irq+0x1d/0x30
[ 1013.773065]  do_IRQ+0x48/0xd0
[ 1013.773067]  common_interrupt+0x93/0x93
[ 1013.773068] RIP: 0033:0xed622c6e42
[ 1013.773069] RSP: 002b:00007ffee8b5c820 EFLAGS: 00000202 ORIG_RAX: ffffffffffffff17
[ 1013.773071] RAX: 000000ed6316a3f0 RBX: 000000ed6316a840 RCX: 00000000000c4e33
[ 1013.773071] RDX: 000000ed6316a878 RSI: 000000ed6316a840 RDI: 000000ed631682d0
[ 1013.773072] RBP: 0000000000000001 R08: 0000000000000001 R09: 000000ed63179b70
[ 1013.773073] R10: 000000000005f6f8 R11: 0000000000000202 R12: 0000000000000001
[ 1013.773074] R13: 00007ffee8b5c85c R14: 000000ed6316a840 R15: 00007ffee8b5c850
[ 1013.773074]  </IRQ>
[ 1013.773076] Code: a9 8a 9a e0 48 8d 75 c4 48 89 da 4c 89 e1 4c 89 ef
e8 54 6e fb ff 48 85 c0 48 89 c3 0f 84 0e 02 00 00 44 0f b7 48 36 4c 8b
70 58 <4d> 8b 7e 20 41 8d 41 fd 66 83 f8 0c 77 6c 0f b7 c0 ff 24 c5 88
[ 1013.773102] RIP: qla24xx_els_ct_entry.isra.17+0x78/0x2a0 [qla2xxx] RSP: ffff88042f603d90
[ 1013.773102] CR2: 0000000300000020
[ 1013.773129] ---[ end trace 532363559924f426 ]---
[ 1013.773131] Kernel panic - not syncing: Fatal exception in interrupt
[ 1013.777719] Kernel Offset: disabled
[ 1013.827528] ---[ end Kernel panic - not syncing: Fatal exception in interrupt

Signed-off-by: Duane Grigsby <Duane.Grigsby@cavium.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Handle PCIe error for driver

Driver will perform following

- Set PFLG_DRIVER_REMOVING flag and do not disable PCIe error reporting
  during adapter shutdown.
- If PCIe device count is already zero, return correct error type from
  PCI error interface.
- When device is offline, return correct error type from PCIe error
  path.
- If there is board disable thread active during shutdown and PCIe
  device count is zero then cancel scheduling board disable thread
  during shutdown and return.

Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix WWPN/WWNN in debug message

Signed-off-by: Darren Trap <darren.trap@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add command completion for error path

The driver held spinlocks during callbacks for NVME errors which
resulted in a deadlock because recovery LS cmds needed the same lock.

Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Update fw_started flags at qpair creation.

Fixes: 4b60c82736d0 ("scsi: qla2xxx: Add fw_started flags to qpair")
Cc: <stable@vger.kernel.org>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix target multiqueue configuration

Following error will be logged in to message file while trying to
configure target with multiqueue.

"Cmd 0x1f aborted with timeout since ISP Abort is pending"
"qla25xx_init_queues Rsp que: 1 init failed."

Fixes: 82de802ad46e ("scsi: qla2xxx: Preparation for Target MQ.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Correction to vha->vref_count timeout

Fix incorrect second argument for wait_event_timeout()

Fixes: c4a9b538ab2a ("qla2xxx: Allow vref count to timeout on vport delete.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: driver version upgrade

Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: call megasas_dump_frame with correct IO frame size

Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: modified few prints in OCR and IOC INIT path

Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: replace internal FALSE/TRUE definitions with false/true

Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: Return pended IOCTLs with cmd_status MFI_STAT_WRONG_STATE in case adapter is dead

After a kill adapter, since the cmd_status is not set, the IOCTLs will
be hung in driver resulting in application hang.  Set cmd_status
MFI_STAT_WRONG_STATE when completing pended IOCTLs.

Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: use vmalloc for crash dump buffers and driver's local RAID map

Driver's local RAID map is accessed frequently. We will first try to get
memory from __get_free_pages. If this fails, fall back to using vmalloc.
For crash dump buffers always prefer vmalloc.

Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: Use SMID for Task abort case only

In TM code, smid_task is valid only in case of task aborts.

Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: Check valid aen class range to avoid kernel panic

Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: Fix endianness issues in DCMD handling

Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: Do not re-fire shutdown DCMD after OCR

Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: Call megasas_complete_cmd_dpc_fusion every 1 second while there are pending commands

megasas_wait_for_outstanding_fusion checks for pending commands every 1
second. But megasas_complete_cmd_dpc_fusion is only called every 5
seconds.  If the commands are already completed by firmware, there is an
additional delay of 5 seconds before driver will process completion for
these commands.

Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: Use synchronize_irq in target reset case

Similar to task abort case, use synchronize_irq API in target reset
case.  Also, remove redundant call to megasas_complete_cmd_dpc_fusion
after calling megasas_sync_irqs in task abort case.

Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: set minimum value of resetwaittime to be 1 secs

Setting resetwaittime to 0 during a FW fault will result in driver not
calling the OCR.

Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: mismatch of allocated MFI frame size and length exposed in MFI MPT pass through command

Driver allocated 256 byte MFI frames bytes but while sending MFI frame
(embedded inside chain frame of MPT frame) to firmware, driver sets the
length as 4k. This results in DMA read error messages during boot.

Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: remove useless code in lpfc_sli4_bsg_link_diag_test

Remove variable assignments. The value stored in local variable _rc_ is
overwritten at line 2448:rc = lpfc_sli4_bsg_set_link_diag_state(phba,
0); before it can be used.

Addresses-Coverity-ID: 1226935
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: sg: protect against races between mmap() and SG_SET_RESERVED_SIZE

Take f_mutex around mmap() processing to protect against races with the
SG_SET_RESERVED_SIZE ioctl.  Ensure the reserve buffer length remains
consistent during the mapping operation, and set the "mmap called" flag
to prevent further changes to the reserved buffer size as an atomic
operation with the mapping.

[mkp: fixed whitespace]

Signed-off-by: Todd Poynor <toddpoynor@google.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: sg: recheck MMAP_IO request length with lock held

Commit 1bc0eb044615 ("scsi: sg: protect accesses to 'reserved' page
array") adds needed concurrency protection for the "reserve" buffer.
Some checks that are initially made outside the lock are replicated once
the lock is taken to ensure the checks and resulting decisions are made
using consistent state.

The check that a request with flag SG_FLAG_MMAP_IO set fits in the
reserve buffer also needs to be performed again under the lock to ensure
the reserve buffer length compared against matches the value in effect
when the request is linked to the reserve buffer.  An -ENOMEM should be
returned in this case, instead of switching over to an indirect buffer
as for non-MMAP_IO requests.

Signed-off-by: Todd Poynor <toddpoynor@google.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hpsa: fix the device_id in hpsa_update_device_info()

The parentheses are in the wrong place so we specify the length as
"sizeof(this_device->device_id) < 0" which is zero.

Fixes: 988b87edd231 ("scsi: hpsa: Ignore errors for unsupported LV_DEVICE_ID VPD page")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aha1542: constify pnp_device_id

pnp_device_id are not supposed to change at runtime. All functions
working with pnp_device_id provided by <linux/pnp.h> work with const
pnp_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: scsi-sysfs: Adjust error returned for adapter reset request

If scsi_host_template->host_reset is NULL and the user requests an
adapter reset through

echo adapter > /sys/class/scsi_host/hostx/host_reset

-EINVAL will be returned even though the "adapter" argument is perfectly
valid.

Change this so that we only return -EINVAL if the provided string is
invalid.  If the host does not implement a ->host_reset function we'll
return -EOPNOTSUPP.

[mkp: tweaked patch description]

Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ch: add refcounting

struct scsi_changer needs refcounting as the device might be removed
while the fd is still open.

[mkp: whitespace]

Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pmcraid: fix duplicated code for different branches

Refactor code in order to avoid identical code for different branches.

This issue was detected with the help of Coccinelle.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ncr5380: constify pnp_device_id

pnp_device_id are not supposed to change at runtime. All functions
working with pnp_device_id provided by <linux/pnp.h> work with const
pnp_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qedf: Update driver version to 8.20.5.0.

Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qedf: Fix up modinfo parameter name for 'debug' in modinfo output.

Because we were passing 'qedf_debug' instead of 'debug' to the
MODULE_PARM_DESC() macro, modinfo listed the parameter name as 'qedf_debug'
instead of it's proper name 'debug'.  Correct the parameter name.

Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qedf: Covert single-threaded workqueues to regular workqueues.

There is no ordering required for the various workqueues the driver uses
so they can be converted to regular workqueues.

Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qedf: Corrent VLAN tag insertion in fallback VLAN case.

Currently in the driver the qedf_ctx attribute vlan_hw_insert is used to
which whether to insert a VLAN tag in FIP frames (except for FIP VLAN
request which is explicitly sent out untagged at least from the driver's
point of view).

When we receive a FIP VLAN response, we set qedf->vlan_hw_insert to 0 which
makes the qedf_fip_send function insert the VLAN.  However when we exhaust
our FIP VLAN retries, we do not set qedf->vlan_hw_insert to 0 which means
that the driver will not tag the FIP frame with the correct VLAN ID.  The
result that was observed on the wire is that some entity either in the LL2
or L2 firmware is adding a NULL VLAN tag which can cause FIP solicitation
to fail.

The offload FCoE frame function, qedf_xmit, does not use the vlan_hw_insert
attribute to decide whether to tag frames with the FIP/FCoE VLAN.  Instead
it unilaterially tags the offload frames with the VLAN ID stored in
qedf->vlan_id. This is the correct behavior so the driver can guarantee
that non-offload FIP frames go out with the correct VLAN ID.

Also use the Linux network layer helpers instead of doing the VLAN insert
manually.

Also fix setting the fallback VLAN so that it used the module parameter and
is not hardcoded to 1002 (though 1002 is the default).

[mkp: fixed typo]

Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qedf: Use granted MAC from the FCF for the FCoE source address if it is available.

Currently in the driver we've been using the fc_fcoe_set_mac() function to
set the source MAC for FCoE traffic.  This works well in most cases as it
uses the spec. default FCF-MAC.  However, if the administrator changes the
FCF-MAC switch, then any FCoE traffic we send will be dropped by the
switch.

Instead we should check the granted MAC from the FLOGI payload and use that
address if it is present.  Otherwise, fall back to using the the default
FCF-MAC and the fabric ID of the port as the FCoE MAC address.

Once this address is known we need to set it when doing non-offload
traffic, offload traffic and setting the data_src_address libfcoe uses for
FIP keep alive messages.

Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qedf: Set WWNN and WWPN based on values from qed.

If dev_info.wwpn and dev_info.wwnn are set by qed use these values to set
the WWNs of the port. Otherwise fall back to the old method using
fcoe_wwn_from_mac().

Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: fix spelling mistake of variable sfp_additonal_info

Trivial fix to variable name, sfp_additonal_info should be
sfp_additional_info (add in missing i).

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: osst: silence underflow warning in osst_verify_frame()

The code looks like this:

i = ntohl(aux->filemark_cnt);
if (STp->header_cache != NULL && i < OS_FM_TAB_MAX && (i > STp->filemark_cnt ||
    STp->first_frame_position - 1 != ntohl(STp->header_cache->dat_fm_tab.fm_tab_ent[i]))) {

If i is negative then it's less than OS_FM_TAB_MAX so we read before
the start of the STp->header_cache->dat_fm_tab.fm_tab_ent[] array.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: osst: add missing indent on a for loop statement

The for loop is statement is missing an indent, add it.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mpt3sas: fix pr_info message continuation

An optional discovery status should be printed with a pr_cont and needs
a leading space to make it more readable. The final new line should also
be a pr_cont and the indentation is out by one, so fix that too.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ses: make page2 support optional

Simple subenclosures do not need to support SES page 2, so make it
optional.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ses: Fixup error message 'failed to get diagnostic page 0xffffffea'

The printk was using the result as argument, leading to a slightly
confusing log message.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ses: check return code from ses_recv_diag()

We should be checking the return code from ses_recv_diag() to avoid
accessing invalid data.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hpsa: Remove 'hpsa_allow_any' module option

As the cciss driver has been removed there are no overlapping
PCI IDs anymore, and the 'hpsa_allow_any' flag can be removed.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: cciss: Drop obsolete driver

The hpsa driver now has support for all boards the cciss driver
used to support, so this patch removes the cciss driver and
make hpsa an alias to cciss.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hpsa: do not print errors for unsupported report luns format

Legacy boards might not support the 'extended' report luns format,
but as this is to be expected we don't need to print out an error here.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hpsa: Ignore errors for unsupported LV_DEVICE_ID VPD page

Legacy boards might not support the LV_DEVICE_ID VPD page, so
we shouldn't print out an error message here.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hpsa: disable volume status check for legacy boards

Legacy boards might not support volume status, so assume
the volume is online here.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hpsa: add support for legacy boards

Add support for legacy boards, ensuring to enable the driver for
those boards only when 'hpsa_allow_any' is set.
The attribute 'legacy_board' is set to '1' if the device is
a legacy board, and '0' otherwise.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: cxlflash: Fix an error handling path in 'cxlflash_disk_attach()'

'rc' is known to be 0 at this point.  If 'create_context()' fails,
returns -ENOMEM instead of 0 which means success.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: sym53c8xx: Avoid undefined behaviour

On parisc I see this UBSAN warning with a sym53c896:

 UBSAN: Undefined behaviour in ./drivers/scsi/sym53c8xx_2/sym_hipd.c:762:24
 index -1903078336 is out of range for type 'u32 [7]'

Avoid this warning by switching to div64_ul().

[mkp: fix typo]

Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: make 'state' device attribute pollable

While the 'state' attribute can (and will) change occasionally,
calling 'poll()' or 'select()' on it fails as sysfs is never
notified that the state has changed.
With this patch calling 'poll()' or 'select()' will work
properly.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: scsi_lib: rework scsi_internal_device_unblock_nowait()

Rework scsi_internal_device_unblock_nowait() into using a switch
statement. No functional changes.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: esas2r: constify pci_device_id.

pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with const
pci_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: virtio: virtio_scsi: Set can_queue to the length of the virtqueue.

Since switching to blk-mq as the default in commit 5c279bd9e406
("scsi: default to scsi-mq"), virtio-scsi LUNs consume about 10x as
much kernel memory.

qemu currently allocates a fixed 128 entry virtqueue.  can_queue
currently is set to 1024.  But with indirect descriptors, each command
in the queue takes 1 virtqueue entry, so the number of commands which
can be queued is equal to the length of the virtqueue.

Note I intend to send a patch to qemu to allow the virtqueue size to be
configured from the qemu command line.

Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: virtio: Reduce BUG if total_sg > virtqueue size to WARN.

If using indirect descriptors, you can make the total_sg as large as you
want.  If not, BUG is too serious because the function later returns
-ENOSPC.

Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qedi: Limit number for CQ queues.

[qed_sp_iscsi_func_start:189(host_7-0)]Cannot satisfy CQ amount. Queues
requested 8, CQs available 4. Aborting function start

Above condition will resolve as management firmware is capable of
telling us the number of CQs available for a given PF, qed will
communicate the same number to qedi, So that qedi will know how much CQs
are allowed.

Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: remove driver versioning

The driver version is not updated with changes to the driver, so it has
no value, so just get rid of it.

Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: replace kfree with scsi_host_put

Instances of kfree(shost) should be replaced with scsi_host_put().

In addition, a missing scsi_host_put() is added for error path in
hisi_sas_shost_alloc_pci() and v3 driver removal.

Signed-off-by: Pan Bian <bianpan2016@163.com> # For main.c changes
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: remove phy_down_v3_hw() res variable

Variable res only holds value 0, so remove it.

This cleans up a coccicheck warning.

Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: add phy_set_linkrate_v3_hw()

Add function to set linkrate for v3 hw.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: update some v3 register init settings

This patch updates some register setting according to recommendation
from HW designer and experiment.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: add reset handler for v3 hw

Use ACPI "_RST" method to reset the controller, since FLR is not
supported.

Function hisi_sas_stop_phys() is introduced to remove some code
duplication.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: kill tasklet when destroying irq in v3 hw

This patch adds calls to kill CQ takslets v3 hw during probe failure.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: fix v3 hw channel interrupt processing

The channel interrupt is to process all the interrupts except PHY
UP/DOWN and broadcast interrupt. So we need to clear all the interrupts
except those 3 interrupts after processing channel interrupts.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: Modify v3 hw STP_LINK_TIMER setting

Modify STP link timer from 10ms to 500ms. Also add the register address.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: add status and command buffer for internal abort

For v3 hw, internal abort function required status and command buffer to
be set, so add necessary code for this.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: support zone management commands

Add two ATA commands, ATA_CMD_ZAC_MGMT_IN and ATA_CMD_ZAC_MGMT_OUT in
hisi_sas_get_ata_protocol(), to support SATA SMR disk.

Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: service interrupt ITCT_CLR interrupt in v2 hw

This patch is a fix related to freeing a device in v2 hw driver.

Before, we polled to ITCT CLR interrupt to check if a device is free.

This was error prone, as if the interrupt doesn't occur in 10us, we miss
processing it.

To avoid this situation, service this interrupt and sync the event with
a completion.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: add irq and tasklet cleanup in v2 hw

This patch adds support to clean-up allocated IRQs and kill tasklets
when probe fails and for driver removal.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: remove repeated device config in v2 hw

This patch removes some repeated configurations:

(1) The device id of the device is already set in the alloc function, so
    we don't need to modify in free device function.

(2) Field dev_type and dev_status are configured in hisi_sas_dev_gone(),
    so there is no need for repeated config in free_device_v3_hw.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: use array for v2 hw ECC errors

The code to print ECC errors in v2 hw driver is very repetitive.  This
patch condensed the code by looping an array of errors.

Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: add v2 hw DFX feature

Add DFX feature for v2 hw. We are adding support for
the following errors:
- loss_of_dword_sync_count
- invalid_dword_count
- phy_reset_problem_count
- running_disparity_error_count

Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: fix v2 hw underflow residual value

The value dw0 is the residual bytes when UNDERFLOW error happens, but we
filled the residual with the value of dw3 before. So change the residual
from dw3 to dw0.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: avoid potential v2 hw interrupt issue

When some interrupts happen together, we need to process every interrupt
one-by-one, and should not return immediately when one interrupt process
is finished being processed.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: fix reset and port ID refresh issues

This patch provides fixes for the following issues:

1. Fix issue of controller reset required to send commands. For reset
   process, it may be required to send commands to the controller, but
   not during soft reset.  So add HISI_SAS_NOT_ACCEPT_CMD_BIT to prevent
   executing a task during this period.

2. Send a broadcast event in rescan topology to detect any topology
   changes during reset.

3. Previously it was not ensured that libsas has processed the PHY up
   and down events after reset. Potentially this could cause an issue
   that we still process the PHY event after reset. So resolve this by
   flushing shot workqueue in LLDD reset.

4. Port ID requires refresh after reset. The port ID generated after
   reset is not guaranteed to be the same as before reset, so it needs
   to be refreshed for each device's ITCT.

Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: smartpqi: change driver version to 1.1.2-125

Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: smartpqi: add in new controller ids

Update the driver’s PCI IDs to match the latest Microsemi controllers

Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: smartpqi: update kexec and power down support

Add PQI reset to driver shutdown callback to work around controller bug.

During an 1.) OS shutdown or 2.) kexec outside of a kdump, the Linux
kernel will clear BME on our controller.

If BME is cleared during a controller/host PCIe transfer, the controller
will lock up.

So we perform a PQI reset in the driver's shutdown callback function to
eliminate the possibility of a controller/host PCIe transfer being
active when the kernel clears BME immediately after calling the driver's
shutdown callback.

Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: smartpqi: cleanup doorbell register usage.

Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: smartpqi: update pqi passthru ioctl

 - make pass-thru requests bi-directional

Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: smartpqi: enhance BMIC cache flush

 - distinguish between shutdown and non-shutdown.

Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: smartpqi: add pqi reset quiesce support

Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: dpt_i2o: remove redundant null check on array device

The null check on pHba->channel[chan].device is redundant because
device is an array and hence can never be null. Remove the check.

Detected by CoverityScan, CID#115362 ("Array compared against 0")

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: use dma_mapping_error to check map errors

The return value of dma_map_single() should be checked by
dma_mapping_error(). However, in function qla26xx_dport_diagnostics(), its
return value is checked against NULL, which could result in failures.

Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mvsas: replace kfree with scsi_host_put

The return value of scsi_host_alloc() should be released by
scsi_host_put(). However, in function mvs_pci_init(), kfree()
is used. This patch replaces kfree() with scsi_host_put() to avoid
possible memory leaks.

Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>