ath9k: improve dma map failure handling

Instead of leaving the buffer without skb and breaking out of the loop
(which could leak the rx buffer), use the common error path.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_common: remove ath9k_cmn_padpos

It is equivalent to ieee80211_hdrlen

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: make various ar5416/ar91xx rf banks const

Banks 0-3,7 are neither modified at run time, nor SREV dependent.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: clean up RF Bank6 handling on AR5416/AR91xx

There are two sets of initvals for this RF bank, one with TPC support and
one without.
The TPC one always gets used, so remove the other one to avoid confusion.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2x00mmio: remove unused rt2x00pci_* defines

All users are converted to use the rt2x00mmio_*
functions so remove the now unused defines.

The patch contain no functional changes.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800pci: use the rt2x00mmio_* routines

Use the recently introduced rt2x00mmio_* routines
instead of the rt2x00pci_* variants.

The patch contains no functional changes.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt61pci: use the rt2x00mmio_* routines

Use the recently introduced rt2x00mmio_* routines
instead of the rt2x00pci_* variants.

The patch contains no functional changes.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2500pci: use the rt2x00mmio_* routines

Use the recently introduced rt2x00mmio_* routines
instead of the rt2x00pci_* variants.

The patch contains no functional changes.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2400pci: use the rt2x00mmio_* routines

Use the recently introduced rt2x00mmio_* routines
instead of the rt2x00pci_* variants.

The patch contains no functional changes.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2x00mmio: use rt2x00mmio prefix in function names

The functions in the rt2x00mmio module has been
moved from the rt2x00pci module. Each function
uses the rt2x00pci prefix which is a bit confusing.
Use the r2x000mmio prefix for each function to make
it consistent with the module name.

The renamed functions are used by several modules,
and updating the names in all of them would result
in a big patch. In order to keep the patch simple,
add compatibility defines for the old function
names. This allows to update the names in each
module separately. After each module is updated,
the defines can be removed.

The patch contains no functional changes.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-john' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next

Merge branch 'for-john' of git://git./linux/kernel/git/jberg/mac80211-next

Conflicts:
drivers/net/wireless/ath/carl9170/debug.c
drivers/net/wireless/ath/carl9170/main.c
net/mac80211/ieee80211_i.h

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless

Conflicts:
drivers/net/wireless/rt2x00/rt2x00pci.c

brcmfmac: only use ifidx from BDC header in brcmf_rx_frames()

In brcmf_rx_frames() the call to brcmf_fweh_process_skb() could
change the ifidx using information in the event data. This is
only different to the BDC ifidx for IF ADD event. However, the
creation of the new interface is deferred to event worker so
it does not exist. After brcmf_fweh_process_skb() it is only
used to set statistics.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: obtain wdev using vif object in action frame rx

The function brcmf_p2p_notify_action_frame_rx() the wireless_dev
is needed to pass the action frame to cfg80211. The wireless_dev
is held in brcmf_cfg80211_vif object. Use that instead of the
ieee80211_ptr in net_device as P2P_DEVICE interface does not have
a net_device associated with it.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: fix reception of P2P probe requests on P2P_DEVICE interface

The probe requests received on P2P_DEVICE interface were not sent
to wpa_supplicant, which makes the device not discoverable by peers.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: wait for firmware event when creating P2P_DEVICE interface

The firmware sends a IF event to notify the host driver that the
P2P_DEVICE interface has been created. Wait for the event before
returning the related wireless_dev.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: support creation of P2P_DEVICE through user-space

The current driver code creates a P2P_DEVICE through a module
parameter. This device has a dummy netdevice which is not how this
interface type is intended. This patch add proper support for the
P2P_DEVICE interface type. This requires a wpa_supplicant with such
support as well.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: use struct brcmf_if instance iso netdevice in escan functions

escan functionality is also required for P2P device operations so it
is better not to rely on struct netdevice instances.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: use struct brcmf_if instance as parameter in brcmf_set_mpc()

Remove use of struct netdevice as parameter to brcmf_set_mpc() as it
will not always be available, ie. there will be non-netdevice interfaces.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove use of unconditional access of struct wireless_dev::netdev

With the introduction of the P2P_DEVICE interface type an instance of
struct wireless_dev does not always have a netdev assigned to it. Better
use container_of() construct to obtain internal structure and go from
there.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove condition for calling event handler

In fweh module the event handler was only called if the
struct brcmf_if instance had a non-null netdev associated.
This restriction is no longer valid for P2P_DEVICE type
of interface. This patch removes that restriction.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add role attribute to struct brcmf_if_event definition

According specification the IF event has an additional field indicating
the role or type of the interface for which this event is sent.

Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add hexadecimal trace of message payload

Adds a trace function used in brcmf_dbg_hex_dump() which adds the
raw binary data to the trace. It requires trace-cmd plugin to see
this data.

Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: firmware shared data version fix

Firware shared data structure is backward compatible for fields
we are interested in.
Allow reading of shared data in case of version mismatch.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: read firmware console without trap indication

Firmware console output can be read also when there was
no trap indication.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: handle firmware signals requesting for packets

The firmware can request the host driver for packets, by sending
either the MAC_REQUEST_CREDIT or the MAC_REQUEST_PACKET primitive.
This patch adds handling of these primitives.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: handle firmware signalling destination entry state

Firmware can signal whether the host driver may sent packets for
a specific destination or interface. This can happen when a
destination is sleeping or when going off-channel.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: fix unaligned access in TXSTATUS signal handling

reported by Hante. Needs to be squashed in commit 187fbcec.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: hold proper locks when accessing ra_list / bss_prio lists

Not locking ra_list when dequeuing packets creates race conditions.
When adding a packet 'tx_pkts_queued' is modified before setting
highest_priority_queue. If in-between the main loop starts, it will
see a packet queued (tx_pkts_queued > 0) but will not find it, since
max prio is not set yet. Depending on the scheduling, the thread
trying to add the packet could complete and restore the situation.
But this is not something to rely on.

Another race condition exists, if a new packet, exceeding current
max prio is added. If concurrently a packet is dequeued, the newly
set max prio will be overwritten with the value of the dequeued
packet. This can occur, because selecting a packet and modifying
the max prio is not atomic. The result in an infinite loop unless,
a new packet is added that has at least the priority of the hidden
packet.

Same applies to bss_prio_tbl. Forward iteration is no proper
lock-free technique and provides no protection from calls to
list_del. Although BSS are currently not added/removed dynamically,
this must not be the case in the future. Hence always hold proper
locks when accessing those lists.

Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: fix infinite loop by removing NO_PKT_PRIO_TID

Using NO_PKT_PRIO_TID and tx_pkts_queued to check for an empty
state, can lead to a contradictory state, resulting in an
infinite loop. Currently queueing and dequeuing of packets is
not synchronized, and can happen concurrently. While tx_pkts_queued
is incremented when adding a packet, max prio is set to NO_PKT when
the WMM list is empty. If a packet is added right after the check
for empty, but before setting max prio to NO_PKT, that packet is
trapped and creates an infinite loop.

Because of the new packet, tx_pkts_queued is at least 1, indicating
wmm lists are not empty. Opposing that max prio is NO_PKT, which
means "skip this wmm queue, it has no packets". The infinite loop
results, because the main loop checks the wmm lists for not empty
via tx_pkts_queued, but for dequeing it uses max_prio to see if it
can skip current list. This will never end, unless a new packet is
added which will restore max prio to the level of the trapped packet.

The solution here is to rely on tx_pkts_queued solely for checking
wmm queue to be empty, and drop the NO_PKT define. It does not
address the locking issue.

Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: remove unused tid_tbl_lock from mwifiex_tid_tbl

ra_list_spinlock is used to protect struct mwifiex_wmm_desc and
embedded structures such as ra_list. tid_tbl_lock while more fine
grained, is not used but in one function. That function is not
called reentrantly. To protect ra_list from concurrent modification
ra_list_spinlock must be held.

Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: correct wrong list in list_empty check

adapter->bss_prio_tbl list has already been checked in outer loop.
The inner loop works with priv_tmp->wmm.tid_tbl_ptr list. Also the
lock taken, gives hint that this is likely a copy-paste error.

Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8188ee: Fix allyesconfig build failures

An allyesconfig build of rtl8188ee yields the following duplicate entry points:

drivers/net/wireless/rtlwifi/rtl8188ee/built-in.o: In function `.rtl92c_phy_ap_calibrate':
(.text+0x21d14): multiple definition of `.rtl92c_phy_ap_calibrate'
drivers/net/wireless/rtlwifi/rtl8192c/built-in.o:(.text+0xb1e8): first defined here
drivers/net/wireless/rtlwifi/rtl8188ee/built-in.o: In function `rtl_hal_pwrseqcmdparsing':
(.opd+0xed0): multiple definition of `rtl_hal_pwrseqcmdparsing'

One of the routines is not used and can be deleted, the other is renamed.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8188ee: Fix linker warnings

Building rtl8188ee yields warnings such as the following:

x86_64-linux-gcc: warning: drivers/net/wireless/rtlwifi: linker input file unused because linking not done

The only potential cause is an extraneous space in the make file.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add support for DFS master mode

These are the remaining knobs in ath9k to support DFS:
* mark AR9280 and AR9580 as DFS tested
* synchronize DFS regulatory domain to reg notifyer
* set required RX filter flags for radar detection
* process radar PHY errors at DFS detector
* notify DFS master on radar detection

DFS support requires CONFIG_ATH9K_DFS_CERTIFIED to be set.

Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add debugfs based DFS radar simulation

This helps testing DFS without radar generating
equipment and is required for certification.

Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add interface combinations for DFS master

Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath: Let user know which keycache method is complaining.

Should make the warning messages more useful.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: fix negative cmd_pending count

cmd_pending is increased in mwifiex_wait_queue_complete() and
decreased in mwifiex_complete_cmd() currently.
If there are two or more commands in the cmd_pending_q the main
worker thread will pick up next command from cmd_pending_q
automatically after finishing current command. As a result
mwifiex_wait_queue_complete() will not be called because
the command is alreay completed. This leads to a negative
number in cmd_pending count.

Fix it by increasing cmd_pending when a cmd is queued into
cmd_pending_q and decreasing when that cmd is recycled. For scan
commands we don't perform inc/dec operations until it's moved
from scan_pending_q to cmd_pending_q. This covers both
synchronous and asynchronous commands.

Reported-by: Daniel Drake <dsd@laptop.org>
Tested-by: Daniel Drake <dsd@laptop.org>
Tested-by: Marco Cesarano <marco@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: dvm: handle FLUSH ampdu actions from mac80211

Until now we didn't handle properly the FLUSH ampdu action
coming from mac80211. This could result in SCD queue leak:
mac80211 would STOP_FLUSH an AMPDU Tx session and remove
the station. If we had still packets on the ring, we
wouldn't deallocate the SCD queue and wait for it to be
empty.
The indication of the queue being empty comes from the Tx
response flow which relies on the tid_data structure. The
problem is that this structure has been cleared when the
station has been removed.
In order to solve this issue, block in the STOP_FLUSH
ampdu_action until the SCD queue is flushed, and only then,
let mac80211 move forward to remove the station.
iwlagn_txfifo_flush had to be enhanced to allow this.

The bug fixed here caused the "txq_id mismatch: 12 0" print.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: mvm: remove users of nvm_data->valid_tx_ant

In commit 332235427a566d8be04b9676a7ac380c8853aa9b
"iwlwifi: mvm: take the valid_{rx,tx}_ant from the TLV"

I replaced the access to nvm_data->valid_tx_ant to an inline
cheking the TLV flags but forgot a few occurences. Fix that.

Change-Id: I92daac735b46738d97fe2dbd5934bb177fd0751b
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-on: https://gerrit.rds.intel.com/12308
Tested-by: IWL Jenkins
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: print warning on request_module failure

If request_module() failed then we didn't have the correct
opmode module that the driver needs to function, so print
a warning in this case to make it more obvious what could
be wrong. This still won't catch the case where the module
simply doesn't exist because it wasn't compiled though.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: make ieee802_11_parse_elems an inline

This (slightly) reduces the code size.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: don't start new netdev queues if driver stopped

If a new netdev (e.g. an AP VLAN) is created while the driver
has queues stopped, the new netdev queues will be started even
though they shouldn't. This will lead to frames accumulating
on the internal mac80211 pending queues instead of properly
being held on the netdev queues.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: replace some dead code by a warning

Given the (nested) switch statements, this code can't
be reached, so make it warn instead of manipulating
the carrier state which seems purposeful.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: don't fiddle with netdev queues in MLME code

The netdev queues should always represent the state that
the driver gave them, so fiddling with them isn't really
appropriate in the mlme code. Also, since we stop queues
for flushing now, this really isn't necessary any more.

As the scan/offchannel code has also been modified to no
longer do this a while ago, remove the outdated smp_mb()
and comments about it.

While at it, also add a pair of braces that was missing.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: disable uAPSD if all ACs are under ACM

It's unlikely that an AP requires WMM mandatory admission control
for all access categories, and if it does then we still transmit
on the background AC without requesting admission. However, avoid
using uAPSD in this case since the implementation could run into
issues and might use other ACs etc.

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: fix do_stop handling while suspended

When a device is unplugged while suspended, mac80211 is
de-initialized and all interfaces are removed while no
state is actually present in the driver. This can cause
warnings and driver confusion.

Fix this by reordering the do_stop code to not call the
driver when it is suspended, i.e. when there's no state
in the driver anyway.

The previous patches removed a few corner cases in ROC
and virtual monitor interfaces so that now this is safe
to do and no state should be left over.

Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: destroy virtual monitor interface across suspend

It has to be removed from the driver, but completely
destroying it helps handle unplug of a device during
suspend since then the channel context handling etc.
doesn't have to happen later when it's removed.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: purge remain-on-channel items when suspending

They can't really be executed while suspended and could
trigger work warnings, so abort all ROC items. When the
system resumes the notifications about this will be
delivered to userspace which can then act accordingly
(though it will assume they were canceled/finished.)

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: remove outdated comment referring to master interface

The code now explicitly calls ieee80211_configure_filter()
anyway, so nothing needs to be explained.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: return new mpath from mesh_path_add()

Most times that mesh_path_add() is called, it is followed by
a lookup to get the just-added mpath.  We can instead just
return the new mpath in the case that we allocated one (or the
existing one if already there), so do that.  Also, reorder the
code in mesh_path_add a bit so that we don't need to allocate
in the pre-existing case.

Signed-off-by: Bob Copeland <bob@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: fix the PREP mesh hwmp debug message

The mesh hwmp debug message is a bit confusing. The "sending PREP
to %p" should be the MAC address of mesh STA that has originated
the PREQ message and the "received PREP from %pM" should be the MAC
address of the mesh STA that has originated the PREP message.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: parse Timeout Interval Element using a struct

Instead of open-coding the accesses and length check do
the length check in the IE parser and assign a struct
pointer for use in the remaining code.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: check ERP info IE length in parser

It's always just one byte, so check for that and
remove the length field from the parser struct.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: check DSSS params IE length in parser

It's always just one byte, so check for that and
remove the length field from the parser struct.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: remove unused IE pointers from parser

There's no need to parse IEs that aren't used
so just remove them.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: remove ancient reference to master interface

The master interface no longer exists ... and hasn't for
a few years now, so remove this reference :-)

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: be more careful about sending beacon-loss-events

I don't think we should send the events unless it was actually
a beacon that was lost...not just any probe of an AP.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: add beacon stats to debugfs

Beacon-timeout and number of beacon loss events.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211_hwsim: advertise VHT support also when channels == 1

Drivers can now advertise VHT support even if they don't use channel
contexts.

Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: let drivers not supporting channel contexts use VHT

It is possible since the global hw config and local switched to
cfg80211_chan_def.

Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: mvm: rename iwl_mvm_new_bt_coex_notif

It actually handles a BT coex notification, so rename it
to be more self explained.
Also, this function can always look at mvm->last_bt_notif
provided that the latter is updated on time.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: mvm: clean up invalid station handling

Using IWL_MVM_STATION_COUNT and IWL_INVALID_STATION together
isn't a good idea as they have different values. Always use
IWL_MVM_STATION_COUNT for an invalid station in MVM and move
the definition of the IWL_INVALID_STATION constant into the
DVM driver to avoid making such mistakes again. The one use
in the transport code can be hard-coded to -1 instead as the
station ID is passed as an integer there.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: add new pci id for 6x35 series

some new thinkpad laptops use intel chip with new pci id need be added
lspci -vnn output:
 Network controller [0280]: Intel Corporation Centrino Advanced-N 6235
 [8086:088f] (rev 24)
 Subsystem: Intel Corporation Device [8086:5260]

Signed-off-by: Shuduo Sang <sangshuduo@gmail.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: mvm: beautify code in BT Coex

The iterators don't need to know what bt_kill_msk means.
All they need to know is if reduced Tx power is enabled
on an interface or not. So change the member of the
iterator to be a bool.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: mvm: Sync FW API time event notification change

The firmware API changed to differentiate between event and
fragment start/end. Change the time-event handling accordingly.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: sleep for at least 10 seconds

Many platforms have issues processing a wakeup signal
while they're still suspending, and will ignore it.
Since our device thinks it woke the platform, and the
platform ignored the signal, it will sleep without
WoWLAN being enabled as the device disables WoWLAN
when having woken the platform.

Resolve this by making the device wait for 10 seconds
after getting the suspend signal before waking up the
platform.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: print opmode when firmware is loaded

Print the sub-driver (opmode, i.e. DVM or MVM) when the
firmware is loaded.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: mvm: remove redundant iwl_power_get_params()

The function just wraps an existing one, remove it.

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: mvm: change active-to-powersave transition time for BPS

The requirement for TX/RX active to powersave transition time for
the Balanced Power Save (BPS) scheme changed. Change the driver
accordingly and set transition time to 100 msec.

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: mvm: encapsulate power table command log message

Encapsulate the power table command logging in a separate
function to print the same information in both cases.

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: mvm: set keepalive period regardless of PM state

The firmware starts sending nulldata frames for keepalive immediately
after association, regardless of power management state. The driver
thus needs to configure keep alive period unconditionally.

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: mvm: always send power table command

The driver distinguishes between power management and device's power
down enablement. Power management enablement depends both on driver's
module power parameters and mac80211 decision. The device's power down
depends only on driver's module power parameters. Change the driver to
always send Power Table command to enable or disable both power
management and device's power down.

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: mvm: Fix active-to-powersave transition time units

Active to power save mode transition time for TX/RX in the power
table command is in microseconds, fix the units in the driver.

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: mvm: don't disable power management due to P2P device

Currently power management is supported only when only a single
virtual interface is present. The driver verifies number of created
interfaces and disables power management when multiple interfaces
present. However, this rule does not extend to a P2P device that is
handled differently in the firmware. If a P2P device is added power
management can remain enabled.

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: mvm: Rename some power management definitions and methods

Replace SLEEP_OVER_DTIM by SKIP_OVER_DTIM.
Add iwl_mvm prefix to a function name.

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: mvm: downgrade to old power management API

Current available FW still doesn't support new PM API.
Therefore, to enable basic power management with the
existing firmware, change the API in the driver back
to the API used in the current firmware.

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: mvm: remove BT Coex constraints upon roaming to A band

When we roam to A band, we don't need to constraint WiFi
any more since it is operating on a different band.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: mvm: implement reduced Tx power

This allows to have better wifi TPT when BT is active under
good RSSI conditions.
Wifi will have better chance to send Acks and Cts even if BT
is active.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: mvm: add per-interface debugfs with mac_params file

Use the per-interface debugfs infrastructure to create a
directory and symlink, and add a file containing debug
data related to each virtual interface.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

brcmfmac: enable sk_buff queueing when credits deplete

Firmware provides the driver with credits used to transmit packets
to the firmware. When credits run out the packets should be queued
and dequeued when receiving creditback signals from the firmware.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: no flow-control tlv signals when fcmode is NONE

The fcmode provided by module parameter defaults to NONE, which
means no flow-control is required. In this case flow-control
signals should not be enabled.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: only allocate firmware-signalling resources if required

Bail out of brcmf_fws_init() when no firmware-signalling is asked
for. Need to take this into account in brcmf_fws_deinit() as well.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: move brcmf_fws_{de,}init() functions

The functions are moved in preparation of later patches.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: correct specified length from FIFOCREDITBACK signal

The length is not according specification so better fix it.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: initialize struct brcmf_fws_info fields before iovar

If iovar to the firmware fails the firmware-signalling module
does a cleanup for which it needs pointer to struct brcmf_pub, which
it gets from struct brcmf_fws_info::drvr. Assign this field before
doing the tlv iovar.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add dedicated log level for low-level sdio debugging

The low-level sdio code has a large number of trace and info messages
that are mostly useful looking into bus specific issues. For tracing
higher-level driver functions it is better to have a dedicated level
for low-level sdio debugging.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Change-Id: Ia424ff18d9033b97aeffc248358e50c51805e815
Reviewed-on: http://lb-bun-88.bun.broadcom.com:8080/74
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: avoid error output on header only packet

During SDIO layer flow control signalling firmware can issue
invalid packets. Prevent printing of parsing errors in such case.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: avoid error output in receive path

Parsing the tlv upon receiving frames can fail. Instead of printing
an error message, just count the parse failure. On some devices we
receive a lot of invalid tlv signals.

this commit will be squashed.

Signed-off-by: Arend van Spriel <arend@broadcom.com>
Change-Id: I08e0f62c55e5028f9aa70c396d291679abd273c9
Reviewed-on: http://lb-bun-88.bun.broadcom.com:8080/72
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: fix handling sk_buff cleanup upon bus tx failure

When firmware-signalling is active the brcmf_txcomplete() does
a free of the sk_buff when transfer to firmware fails in the
bus-specific driver code. However, it should also cleanup the
packet from the hanger. This patch fixes that.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: enable tx status signalling

Enabling the tx status signalling, which requires packet tagging
before sending to the firmware and handling the tx status signal.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add flow-control mode to firmware signalling

Upcoming patches will add firmware signalled flow control. Prepare
by adding the mode, which defaults to disable it. The mode can be
queried by brcmf_fws_fc_active() and set by a module parameter.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add optional bus callback definition for tx queue cleanup

Add a callback to obtain packet queue from the bus-specific code
used to cleanup packet buffers from firmware-signalling code.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add firmware-signalling hanger functions

The hanger for firmware-signalling is used to retain information for
outstanding transmit packets that await tx status.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: perform filtered firmware-signalling cleanup upon DEL_IF

When an interface is deleted make sure to cleanup all packet
buffers related to that interface.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add definitions for handling sk_buff control buffer data

The sk_buff structure contains a control buffer that can be used
by different layers in the networking stack for holding packet
associated information. In brcmfmac it is used to hold firmware
signalling related information.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: allow stopping netif queue for different reasons

Currently, the netif queue is only stopped when the bus interface is
giving a push back. This will change soon so prepare the driver by
adding a stop reason and stop/resume the queue accordingly.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add firmware-signalling cleanup function

Add a cleanup function releasing any queued packet buffers in
the mac descriptor entries.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>