dm: allocate struct mapped_device with kvzalloc

commit 856eb0916d181da6d043cc33e03f54d5c5bbe54a upstream.

The structure srcu_struct can be very big, its size is proportional to the
value CONFIG_NR_CPUS. The Fedora kernel has CONFIG_NR_CPUS 8192, the field
io_barrier in the struct mapped_device has 84kB in the debugging kernel
and 50kB in the non-debugging kernel. The large size may result in failure
of the function kzalloc_node.

In order to avoid the allocation failure, we use the function
kvzalloc_node, this function falls back to vmalloc if a large contiguous
chunk of memory is not available. This patch also moves the field
io_barrier to the last position of struct mapped_device - the reason is
that on many processor architectures, short memory offsets result in
smaller code than long memory offsets - on x86-64 it reduces code size by
320 bytes.

Note to stable kernel maintainers - the kernels 4.11 and older don't have
the function kvzalloc_node, you can use the function vzalloc_node instead.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ovl: Put upperdentry if ovl_check_origin() fails

commit 5455f92b54e516995a9ca45bbf790d3629c27a93 upstream.

If ovl_check_origin() fails, we should put upperdentry. We have a reference
on it by now. So goto out_put_upper instead of out.

Fixes: a9d019573e88 ("ovl: lookup non-dir copy-up-origin by file handle")
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm bufio: fix integer overflow when limiting maximum cache size

commit 74d4108d9e681dbbe4a2940ed8fdff1f6868184c upstream.

The default max_cache_size_bytes for dm-bufio is meant to be the lesser
of 25% of the size of the vmalloc area and 2% of the size of lowmem.
However, on 32-bit systems the intermediate result in the expression

    (VMALLOC_END - VMALLOC_START) * DM_BUFIO_VMALLOC_PERCENT / 100

overflows, causing the wrong result to be computed.  For example, on a
32-bit system where the vmalloc area is 520093696 bytes, the result is
1174405 rather than the expected 130023424, which makes the maximum
cache size much too small (far less than 2% of lowmem).  This causes
severe performance problems for dm-verity users on affected systems.

Fix this by using mult_frac() to correctly multiply by a percentage.  Do
this for all places in dm-bufio that multiply by a percentage.  Also
replace (VMALLOC_END - VMALLOC_START) with VMALLOC_TOTAL, which contrary
to the comment is now defined in include/linux/vmalloc.h.

Depends-on: 9993bc635 ("sched/x86: Fix overflow in cyc2ns_offset")
Fixes: 95d402f057f2 ("dm: add bufio")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm mpath: remove annoying message of 'blk_get_request() returned -11'

commit 9dc112e2daf87b40607fd8d357e2d7de32290d45 upstream.

It is very normal to see allocation failure, especially with blk-mq
request_queues, so it's unnecessary to report this error and annoy
people.

In practice this 'blk_get_request() returned -11' error gets logged
quite frequently when a blk-mq DM multipath device sees heavy IO.

This change is marked for stable@ because the annoying message in
question was included in stable@ commit 7083abbbf.

Fixes: 7083abbbf ("dm mpath: avoid that path removal can trigger an infinite loop")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm zoned: ignore last smaller runt zone

commit 114e025968b5990ad0b57bf60697ea64ee206aac upstream.

The SCSI layer allows ZBC drives to have a smaller last runt zone. For
such a device, specifying the entire capacity for a dm-zoned target
table entry fails because the specified capacity is not aligned on a
device zone size indicated in the request queue structure of the
device.

Fix this problem by ignoring the last runt zone in the entry length
when seting up the dm-zoned target (ctr method) and when iterating table
entries of the target (iterate_devices method). This allows dm-zoned
users to still easily setup a target using the entire device capacity
(as mandated by dm-zoned) or the aligned capacity excluding the last
runt zone.

While at it, replace direct references to the device queue chunk_sectors
limit with calls to the accessor blk_queue_zone_sectors().

Reported-by: Peter Desnoyers <pjd@ccs.neu.edu>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm crypt: allow unaligned bv_offset

commit 0440d5c0ca9744b92a07aeb6df0a9a75db6f4280 upstream.

When slub_debug is enabled kmalloc returns unaligned memory. XFS uses
this unaligned memory for its buffers (if an unaligned buffer crosses a
page, XFS frees it and allocates a full page instead - see the function
xfs_buf_allocate_memory).

dm-crypt checks if bv_offset is aligned on page size and these checks
fail with slub_debug and XFS.

Fix this bug by removing the bv_offset checks. Switch to checking if
bv_len is aligned instead of bv_offset (this check should be sufficient
to prevent overruns if a bio with too small bv_len is received).

Fixes: 8f0009a22517 ("dm crypt: optionally support larger encryption sector size")
Reported-by: Bruno Prémont <bonbons@sysophe.eu>
Tested-by: Bruno Prémont <bonbons@sysophe.eu>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm cache: fix race condition in the writeback mode overwrite_bio optimisation

commit d1260e2a3f85f4c1010510a15f89597001318b1b upstream.

When a DM cache in writeback mode moves data between the slow and fast
device it can often avoid a copy if the triggering bio either:

i) covers the whole block (no point copying if we're about to overwrite it)
ii) the migration is a promotion and the origin block is currently discarded

Prior to this fix there was a race with case (ii).  The discard status
was checked with a shared lock held (rather than exclusive).  This meant
another bio could run in parallel and write data to the origin, removing
the discard state.  After the promotion the parallel write would have
been lost.

With this fix the discard status is re-checked once the exclusive lock
has been aquired.  If the block is no longer discarded it falls back to
the slower full copy path.

Fixes: b29d4986d ("dm cache: significant rework to leverage dm-bio-prison-v2")
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm integrity: allow unaligned bv_offset

commit 95b1369a9638cfa322ad1c0cde8efbe524059884 upstream.

When slub_debug is enabled kmalloc returns unaligned memory. XFS uses
this unaligned memory for its buffers (if an unaligned buffer crosses a
page, XFS frees it and allocates a full page instead - see the function
xfs_buf_allocate_memory).

dm-integrity checks if bv_offset is aligned on page size and this check
fail with slub_debug and XFS.

Fix this bug by removing the bv_offset check, leaving only the check for
bv_len.

Fixes: 7eada909bfd7 ("dm: add integrity target")
Reported-by: Bruno Prémont <bonbons@sysophe.eu>
Reviewed-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda: Add Raven PCI ID

commit 9ceace3c9c18c67676e75141032a65a8e01f9a7a upstream.

This commit adds PCI ID for Raven platform

Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: Apply Cavium ThunderX ACS quirk to more Root Ports

commit f2ddaf8dfd4a5071ad09074d2f95ab85d35c8a1e upstream.

Extend the Cavium ThunderX ACS quirk to cover more device IDs and restrict
it to only Root Ports.

Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
[bhelgaas: changelog, stable tag]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: Set Cavium ACS capability quirk flags to assert RR/CR/SV/UF

commit 7f342678634f16795892677204366e835e450dda upstream.

The Cavium ThunderX (CN8XXX) family of PCIe Root Ports does not advertise
an ACS capability.  However, the RTL internally implements similar
protection as if ACS had Request Redirection, Completion Redirection,
Source Validation, and Upstream Forwarding features enabled.

Change Cavium ACS capabilities quirk flags accordingly.

Fixes: b404bcfbf035 ("PCI: Add ACS quirk for all Cavium devices")
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
[bhelgaas: tidy changelog, comment, stable tag]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: hv: Use effective affinity mask

commit 79aa801e899417a56863d6713f76c4e108856000 upstream.

The effective_affinity_mask is always set when an interrupt is assigned in
__assign_irq_vector() -> apic->cpu_mask_to_apicid(), e.g. for struct apic
apic_physflat: -> default_cpu_mask_to_apicid() ->
irq_data_update_effective_affinity(), but it looks d->common->affinity
remains all-1's before the user space or the kernel changes it later.

In the early allocation/initialization phase of an IRQ, we should use the
effective_affinity_mask, otherwise Hyper-V may not deliver the interrupt to
the expected CPU.  Without the patch, if we assign 7 Mellanox ConnectX-3
VFs to a 32-vCPU VM, one of the VFs may fail to receive interrupts.

Tested-by: Adrian Suhov <v-adsuho@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jake Oshins <jakeo@microsoft.com>
Cc: Jork Loeser <jloeser@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI/ASPM: Use correct capability pointer to program LTR_L1.2_THRESHOLD

commit c00054f540bf81e592e1fee709b0bdbf20f478b5 upstream.

Previously we programmed the LTR_L1.2_THRESHOLD in the parent (upstream)
device using the capability pointer of the *child* (downstream) device,
which corrupted some random word of the parent's config space.

Use the parent's L1 SS capability pointer to program its
LTR_L1.2_THRESHOLD.

Fixes: aeda9adebab8 ("PCI/ASPM: Configure L1 substate settings")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
CC: Rajat Jain <rajatja@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI/ASPM: Account for downstream device's Port Common_Mode_Restore_Time

commit 94ac327e043ee40d7fc57b54541da50507ef4e99 upstream.

Every Port that supports the L1.2 substate advertises its Port
Common_Mode_Restore_Time, i.e., the time the Port requires to re-establish
common mode when exiting L1.2 (see PCIe r3.1, sec 7.33.2).

Per sec 5.5.3.3.1, when exiting L1.2, the Downstream Port (the device at
the upstream end of the link) must send TS1 training sequences for at least
T(COMMONMODE) after it detects electrical idle exit on the Link.  We want
this to be long enough for both ends of the Link, so we should set it to
the maximum of the Port Common_Mode_Restore_Time for the upstream and
downstream components on the Link.

Previously we only looked at the Port Common_Mode_Restore_Time of the
upstream device, so if the downstream device required more time, we didn't
program the upstream device's T(COMMONMODE) correctly.

Fixes: f1f0366dd6be ("PCI/ASPM: Calculate and save the L1.2 timing parameters")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Acked-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PM / OPP: Add missing of_node_put(np)

commit 7978db344719dab1e56d05e6fc04aaaddcde0a5e upstream.

The for_each_available_child_of_node() loop in _of_add_opp_table_v2()
doesn't drop the reference to "np" on errors. Fix that.

Fixes: 274659029c9d (PM / OPP: Add support to parse "operating-points-v2" bindings)
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
[ VK: Improved commit log. ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nbd: don't start req until after the dead connection logic

commit 6a468d5990ecd1c2d07dd85f8633bbdd0ba61c40 upstream.

We can end up sleeping for a while waiting for the dead timeout, which
means we could get the per request timer to fire.  We did handle this
case, but if the dead timeout happened right after we submitted we'd
either tear down the connection or possibly requeue as we're handling an
error and race with the endio which can lead to panics and other
hilarity.

Fixes: 560bc4b39952 ("nbd: handle dead connections")
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nbd: wait uninterruptible for the dead timeout

commit ff57dc94faec023abc267cdc45766fccff497557 upstream.

If we have a pending signal or the user kills their application then
it'll bring down the whole device, which is less than awesome.  Instead
wait uninterruptible for the dead timeout so we're sure we gave it our
best shot.

Fixes: 560bc4b39952 ("nbd: handle dead connections")
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: mvneta: fix handling of the Tx descriptor counter

commit 0d63785c6b94b5d2f095f90755825f90eea791f5 upstream.

The mvneta controller provides a 8-bit register to update the pending
Tx descriptor counter. Then, a maximum of 255 Tx descriptors can be
added at once. In the current code the mvneta_txq_pend_desc_add function
assumes the caller takes care of this limit. But it is not the case. In
some situations (xmit_more flag), more than 255 descriptors are added.
When this happens, the Tx descriptor counter register is updated with a
wrong value, which breaks the whole Tx queue management.

This patch fixes the issue by allowing the mvneta_txq_pend_desc_add
function to process more than 255 Tx descriptors.

Fixes: 2a90f7e1d5d0 ("net: mvneta: add xmit_more support")
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: ralink: Fix typo in mt7628 pinmux function

commit 05a67cc258e75ac9758e6f13d26337b8be51162a upstream.

There is a typo inside the pinmux setup code. The function is called
refclk and not reclk.

Fixes: 53263a1c6852 ("MIPS: ralink: add mt7628an support")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: John Crispin <john@phrozen.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16047/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: ralink: Fix MT7628 pinmux

commit 8ef4b43cd3794d63052d85898e42424fd3b14d24 upstream.

According to the datasheet the REFCLK pin is shared with GPIO#37 and
the PERST pin is shared with GPIO#36.

Fixes: 53263a1c6852 ("MIPS: ralink: add mt7628an support")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: John Crispin <john@phrozen.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16046/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: cmpxchg64() and HAVE_VIRT_CPU_ACCOUNTING_GEN don't work for 32-bit SMP

commit a3f143106596d739e7fbc4b84c96b1475247d876 upstream.

__cmpxchg64_local_generic() is atomic only w.r.t tasks and interrupts
on the same CPU (that's what the 'local' means).  We can't use it to
implement cmpxchg64() in SMP configurations.

So, for 32-bit SMP configurations:

- Don't define cmpxchg64()
- Don't enable HAVE_VIRT_CPU_ACCOUNTING_GEN, which requires it

Fixes: e2093c7b03c1 ("MIPS: Fall back to generic implementation of ...")
Fixes: bb877e96bea1 ("MIPS: Add support for full dynticks CPU time accounting")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Deng-Cheng Zhu <dengcheng.zhu@mips.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17413/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

uapi: fix linux/rxrpc.h userspace compilation errors

commit 0eef304bc9f7d079a1165e8cd2f24b078e9e1f2a upstream.

Consistently use types provided by <linux/types.h> to fix the following
linux/rxrpc.h userspace compilation errors:

/usr/include/linux/rxrpc.h:24:2: error: unknown type name 'u16'
  u16  srx_service; /* service desired */
/usr/include/linux/rxrpc.h:25:2: error: unknown type name 'u16'
  u16  transport_type; /* type of transport socket (SOCK_DGRAM) */
/usr/include/linux/rxrpc.h:26:2: error: unknown type name 'u16'
  u16  transport_len; /* length of transport address */

Use __kernel_sa_family_t instead of sa_family_t the same way
as uapi/linux/in.h does, to fix the following
linux/rxrpc.h userspace compilation errors:

/usr/include/linux/rxrpc.h:23:2: error: unknown type name 'sa_family_t'
  sa_family_t srx_family; /* address family */
/usr/include/linux/rxrpc.h:28:3: error: unknown type name 'sa_family_t'
  sa_family_t family;  /* transport address family */

Fixes: 727f8914477e ("rxrpc: Expose UAPI definitions to userspace")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

uapi: fix linux/tls.h userspace compilation error

commit b9f3eb499d84f8d4adcb2f9212ec655700b28228 upstream.

Move inclusion of a private kernel header <net/tcp.h>
from uapi/linux/tls.h to its only user - net/tls.h,
to fix the following linux/tls.h userspace compilation error:

/usr/include/linux/tls.h:41:21: fatal error: net/tcp.h: No such file or directory

As to this point uapi/linux/tls.h was totaly unusuable for userspace,
cleanup this header file further by moving other redundant includes
to net/tls.h.

Fixes: 3c4d7559159b ("tls: kernel TLS support")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: 8721/1: mm: dump: check hardware RO bit for LPAE

commit 3b0c0c922ff4be275a8beb87ce5657d16f355b54 upstream.

When CONFIG_ARM_LPAE is set, the PMD dump relies on the software
read-only bit to determine whether a page is writable. This
concealed a bug which left the kernel text section writable
(AP2=0) while marked read-only in the software bit.

In a kernel with the AP2 bug, the dump looks like this:

    ---[ Kernel Mapping ]---
    0xc0000000-0xc0200000           2M RW NX SHD
    0xc0200000-0xc0600000           4M ro x  SHD
    0xc0600000-0xc0800000           2M ro NX SHD
    0xc0800000-0xc4800000          64M RW NX SHD

The fix is to check that the software and hardware bits are both
set before displaying "ro". The dump then shows the true perms:

    ---[ Kernel Mapping ]---
    0xc0000000-0xc0200000           2M RW NX SHD
    0xc0200000-0xc0600000           4M RW x  SHD
    0xc0600000-0xc0800000           2M RW NX SHD
    0xc0800000-0xc4800000          64M RW NX SHD

Fixes: ded947798469 ("ARM: 8109/1: mm: Modify pte_write and pmd_write logic for LPAE")
Signed-off-by: Philip Derrin <philip@cog.systems>
Tested-by: Neil Dick <neil@cog.systems>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: 8722/1: mm: make STRICT_KERNEL_RWX effective for LPAE

commit 400eeffaffc7232c0ae1134fe04e14ae4fb48d8c upstream.

Currently, for ARM kernels with CONFIG_ARM_LPAE and
CONFIG_STRICT_KERNEL_RWX enabled, the 2MiB pages mapping the
kernel code and rodata are writable. They are marked read-only in
a software bit (L_PMD_SECT_RDONLY) but the hardware read-only bit
is not set (PMD_SECT_AP2).

For user mappings, the logic that propagates the software bit
to the hardware bit is in set_pmd_at(); but for the kernel,
section_update() writes the PMDs directly, skipping this logic.

The fix is to set PMD_SECT_AP2 for read-only sections in
section_update(), at the same time as L_PMD_SECT_RDONLY.

Fixes: 1e3479225acb ("ARM: 8275/1: mm: fix PMD_SECT_RDONLY undeclared compile error")
Signed-off-by: Philip Derrin <philip@cog.systems>
Reported-by: Neil Dick <neil@cog.systems>
Tested-by: Neil Dick <neil@cog.systems>
Tested-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: Implement arch-specific pte_access_permitted()

commit 6218f96c58dbf44a06aeaf767aab1f54fc397838 upstream.

The generic pte_access_permitted() implementation only checks for
pte_present() (together with the write permission where applicable).
However, for both kernel ptes and PROT_NONE mappings pte_present() also
returns true on arm64 even though such mappings are not user accessible.
Additionally, arm64 now supports execute-only user permission
(PROT_EXEC) which is implemented by clearing the PTE_USER bit.

With this patch the arm64 implementation of pte_access_permitted()
checks for the PTE_VALID and PTE_USER bits together with writable access
if applicable.

Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf/x86/intel: Hide TSX events when RTM is not supported

commit 58ba4d5a25579e5c7e312bd359c95f3a9a0a242c upstream.

0day testing reported a perf test regression on Haswell systems without
RTM. Commit a5df70c35 hides the in_tx/in_tx_cp attributes when RTM is not
available, but the TSX events are still available in sysfs. Due to the
missing attributes the event parser fails on those files.

Don't show the TSX events in sysfs when RTM is not available on
Haswell/Broadwell/Skylake.

Fixes: a5df70c354c2 (perf/x86: Only show format attributes when supported)
Reported-by: kernel test robot <xiaolong.ye@intel.com>
Tested-by: Jin Yao <yao.jin@linux.intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20171109000718.14137-1-andi@firstfloor.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/entry/64: Add missing irqflags tracing to native_load_gs_index()

commit ca37e57bbe0cf1455ea3e84eb89ed04a132d59e1 upstream.

Running this code with IRQs enabled (where dummy_lock is a spinlock):

static void check_load_gs_index(void)
{
/* This will fail. */
load_gs_index(0xffff);

spin_lock(&dummy_lock);
spin_unlock(&dummy_lock);
}

Will generate a lockdep warning.  The issue is that the actual write
to %gs would cause an exception with IRQs disabled, and the exception
handler would, as an inadvertent side effect, update irqflag tracing
to reflect the IRQs-off status.  native_load_gs_index() would then
turn IRQs back on and return with irqflag tracing still thinking that
IRQs were off.  The dummy lock-and-unlock causes lockdep to notice the
error and warn.

Fix it by adding the missing tracing.

Apparently nothing did this in a context where it mattered.  I haven't
tried to find a code path that would actually exhibit the warning if
appropriately nasty user code were running.

I suspect that the security impact of this bug is very, very low --
production systems don't run with lockdep enabled, and the warning is
mostly harmless anyway.

Found during a quick audit of the entry code to try to track down an
unrelated bug that Ingo found in some still-in-development code.

Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bpetkov@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/e1aeb0e6ba8dd430ec36c8a35e63b429698b4132.1511411918.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/entry/64: Fix entry_SYSCALL_64_after_hwframe() IRQ tracing

commit 548c3050ea8d16997ae27f9e080a8338a606fc93 upstream.

When I added entry_SYSCALL_64_after_hwframe(), I left TRACE_IRQS_OFF
before it.  This means that users of entry_SYSCALL_64_after_hwframe()
were responsible for invoking TRACE_IRQS_OFF, and the one and only
user (Xen, added in the same commit) got it wrong.

I think this would manifest as a warning if a Xen PV guest with
CONFIG_DEBUG_LOCKDEP=y were used with context tracking.  (The
context tracking bit is to cause lockdep to get invoked before we
turn IRQs back on.)  I haven't tested that for real yet because I
can't get a kernel configured like that to boot at all on Xen PV.

Move TRACE_IRQS_OFF below the label.

Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bpetkov@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 8a9949bc71a7 ("x86/xen/64: Rearrange the SYSCALL entries")
Link: http://lkml.kernel.org/r/9150aac013b7b95d62c2336751d5b6e91d2722aa.1511325444.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/decoder: Add new TEST instruction pattern

commit 12a78d43de767eaf8fb272facb7a7b6f2dc6a9df upstream.

The kbuild test robot reported this build warning:

  Warning: arch/x86/tools/test_get_len found difference at <jump_table>:ffffffff8103dd2c

  Warning: ffffffff8103dd82: f6 09 d8 testb $0xd8,(%rcx)
  Warning: objdump says 3 bytes, but insn_get_length() says 2
  Warning: decoded and checked 1569014 instructions with 1 warnings

This sequence seems to be a new instruction not in the opcode map in the Intel SDM.

The instruction sequence is "F6 09 d8", means Group3(F6), MOD(00)REG(001)RM(001), and 0xd8.
Intel SDM vol2 A.4 Table A-6 said the table index in the group is "Encoding of Bits 5,4,3 of
the ModR/M Byte (bits 2,1,0 in parenthesis)"

In that table, opcodes listed by the index REG bits as:

  000         001       010 011  100        101        110         111
 TEST Ib/Iz,(undefined),NOT,NEG,MUL AL/rAX,IMUL AL/rAX,DIV AL/rAX,IDIV AL/rAX

So, it seems TEST Ib is assigned to 001.

Add the new pattern.

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/boot: Fix boot failure when SMP MP-table is based at 0

commit ac5292e9a294618cecb31109d1ba265e3d027ba2 upstream.

When crosvm is used to boot a kernel as a VM, the SMP MP-table is found
at physical address 0x0. This causes mpf_base to be set to 0 and a
subsequent "if (!mpf_base)" check in default_get_smp_config() results in
the MP-table not being parsed.  Further into the boot this results in an
oops when attempting a read_apic_id().

Add a boolean variable that is set to true when the MP-table is found.
Use this variable for testing if the MP-table was found so that even a
value of 0 for mpf_base will result in continued parsing of the MP-table.

Fixes: 5997efb96756 ("x86/boot: Use memremap() to map the MPF and MPC data")
Reported-by: Tomeu Vizoso <tomeu@tomeuvizoso.net>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: regression@leemhuis.info
Link: https://lkml.kernel.org/r/20171106201753.23059.86674.stgit@tlendack-t1.amdoffice.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

lib/mpi: call cond_resched() from mpi_powm() loop

commit 1d9ddde12e3c9bab7f3d3484eb9446315e3571ca upstream.

On a non-preemptible kernel, if KEYCTL_DH_COMPUTE is called with the
largest permitted inputs (16384 bits), the kernel spends 10+ seconds
doing modular exponentiation in mpi_powm() without rescheduling.  If all
threads do it, it locks up the system.  Moreover, it can cause
rcu_sched-stall warnings.

Notwithstanding the insanity of doing this calculation in kernel mode
rather than in userspace, fix it by calling cond_resched() as each bit
from the exponent is processed.  It's still noninterruptible, but at
least it's preemptible now.

Do the cond_resched() once per bit rather than once per MPI limb because
each limb might still easily take 100+ milliseconds on slow CPUs.

Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sched: Make resched_cpu() unconditional

commit 7c2102e56a3f7d85b5d8f33efbd7aecc1f36fdd8 upstream.

The current implementation of synchronize_sched_expedited() incorrectly
assumes that resched_cpu() is unconditional, which it is not.  This means
that synchronize_sched_expedited() can hang when resched_cpu()'s trylock
fails as follows (analysis by Neeraj Upadhyay):

o CPU1 is waiting for expedited wait to complete:

sync_rcu_exp_select_cpus
     rdp->exp_dynticks_snap & 0x1   // returns 1 for CPU5
     IPI sent to CPU5

synchronize_sched_expedited_wait
 ret = swait_event_timeout(rsp->expedited_wq,
   sync_rcu_preempt_exp_done(rnp_root),
   jiffies_stall);

expmask = 0x20, CPU 5 in idle path (in cpuidle_enter())

o CPU5 handles IPI and fails to acquire rq lock.

Handles IPI
     sync_sched_exp_handler
 resched_cpu
     returns while failing to try lock acquire rq->lock
 need_resched is not set

o CPU5 calls  rcu_idle_enter() and as need_resched is not set, goes to
idle (schedule() is not called).

o CPU 1 reports RCU stall.

Given that resched_cpu() is now used only by RCU, this commit fixes the
assumption by making resched_cpu() unconditional.

Reported-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Suggested-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serdev: fix registration of second slave

commit 08fcee289f341786eb3b44e5f2d1dc850943238e upstream.

Serdev currently only supports a single slave device, but the required
sanity checks to prevent further registration attempts were missing.

If a serial-port node has two child nodes with compatible properties,
the OF code would try to register two slave devices using the same id
and name. Driver core will not allow this (and there will be loud
complaints), but the controller's slave pointer would already have been
set to address of the soon to be deallocated second struct
serdev_device. As the first slave device remains registered, this can
lead to later use-after-free issues when the slave callbacks are
accessed.

Note that while the serdev registration helpers are exported, they are
typically only called by serdev core. Any other (out-of-tree) callers
must serialise registration and deregistration themselves.

Fixes: cd6484e1830b ("serdev: Introduce new bus for serial attached devices")
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cpufreq: schedutil: Reset cached_raw_freq when not in sync with next_freq

commit 07458f6a5171d97511dfbdf6ce549ed2ca0280c7 upstream.

'cached_raw_freq' is used to get the next frequency quickly but should
always be in sync with sg_policy->next_freq. There is a case where it is
not and in such cases it should be reset to avoid switching to incorrect
frequencies.

Consider this case for example:

 - policy->cur is 1.2 GHz (Max)
 - New request comes for 780 MHz and we store that in cached_raw_freq.
 - Based on 780 MHz, we calculate the effective frequency as 800 MHz.
 - We then see the CPU wasn't idle recently and choose to keep the next
   freq as 1.2 GHz.
 - Now we have cached_raw_freq is 780 MHz and sg_policy->next_freq is
   1.2 GHz.
 - Now if the utilization doesn't change in then next request, then the
   next target frequency will still be 780 MHz and it will match with
   cached_raw_freq. But we will choose 1.2 GHz instead of 800 MHz here.

Fixes: b7eaf1aab9f8 (cpufreq: schedutil: Avoid reducing frequency of busy CPUs prematurely)
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ACPI / EC: Fix regression related to triggering source of EC event handling

commit 53c5eaabaea9a1b7a96f95ccc486d2ad721d95bb upstream.

Originally the Samsung quirks removed by commit 4c237371 can be covered
by commit e923e8e7 and ec_freeze_events=Y mode. But commit 9c40f956
changed ec_freeze_events=Y back to N, making this problem re-surface.

Actually, if commit e923e8e7 is robust enough, we can freely change
ec_freeze_events mode, so this patch fixes the issue by improving
commit e923e8e7.

Related commits listed in the merged order:

 Commit: e923e8e79e18fd6be9162f1be6b99a002e9df2cb
 Subject: ACPI / EC: Fix an issue that SCI_EVT cannot be detected
          after event is enabled

 Commit: 4c237371f290d1ed3b2071dd43554362137b1cce
 Subject: ACPI / EC: Remove old CLEAR_ON_RESUME quirk

 Commit: 9c40f956ce9b331493347d1b3cb7e384f7dc0581
 Subject: Revert "ACPI / EC: Enable event freeze mode..." to fix
          a regression

This patch not only fixes the reported post-resume EC event triggering
source issue, but also fixes an unreported similar issue related to the
driver bind by adding EC event triggering source in ec_install_handlers().

Fixes: e923e8e79e18 (ACPI / EC: Fix an issue that SCI_EVT cannot be detected after event is enabled)
Fixes: 4c237371f290 (ACPI / EC: Remove old CLEAR_ON_RESUME quirk)
Fixes: 9c40f956ce9b (Revert "ACPI / EC: Enable event freeze mode..." to fix a regression)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196833
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reported-by: Alistair Hamilton <ahpatent@gmail.com>
Tested-by: Alistair Hamilton <ahpatent@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ACPI / PM: Fix acpi_pm_notifier_lock vs flush_workqueue() deadlock

commit ff1656790b3a4caca94505c52fd0250f981ea187 upstream.

acpi_remove_pm_notifier() ends up calling flush_workqueue() while
holding acpi_pm_notifier_lock, and that same lock is taken by
by the work via acpi_pm_notify_handler(). This can deadlock.

To fix the problem let's split the single lock into two: one to
protect the dev->wakeup between the work vs. add/remove, and
another one to handle notifier installation vs. removal.

After commit a1d14934ea4b "workqueue/lockdep: 'Fix' flush_work()
annotation" I was able to kill the machine (Intel Braswell)
very easily with 'powertop --auto-tune', runtime suspending i915,
and trying to wake it up via the USB keyboard. The cases when
it didn't die are presumably explained by lockdep getting disabled
by something else (cpu hotplug locking issues usually).

Fortunately I still got a lockdep report over netconsole
(trickling in very slowly), even though the machine was
otherwise practically dead:

[  112.179806] ======================================================
[  114.670858] WARNING: possible circular locking dependency detected
[  117.155663] 4.13.0-rc6-bsw-bisect-00169-ga1d14934ea4b #119 Not tainted
[  119.658101] ------------------------------------------------------
[  121.310242] xhci_hcd 0000:00:14.0: xHCI host not responding to stop endpoint command.
[  121.313294] xhci_hcd 0000:00:14.0: xHCI host controller not responding, assume dead
[  121.313346] xhci_hcd 0000:00:14.0: HC died; cleaning up
[  121.313485] usb 1-6: USB disconnect, device number 3
[  121.313501] usb 1-6.2: USB disconnect, device number 4
[  134.747383] kworker/0:2/47 is trying to acquire lock:
[  137.220790]  (acpi_pm_notifier_lock){+.+.}, at: [<ffffffff813cafdf>] acpi_pm_notify_handler+0x2f/0x80
[  139.721524]
[  139.721524] but task is already holding lock:
[  144.672922]  ((&dpc->work)){+.+.}, at: [<ffffffff8109ce90>] process_one_work+0x160/0x720
[  147.184450]
[  147.184450] which lock already depends on the new lock.
[  147.184450]
[  154.604711]
[  154.604711] the existing dependency chain (in reverse order) is:
[  159.447888]
[  159.447888] -> #2 ((&dpc->work)){+.+.}:
[  164.183486]        __lock_acquire+0x1255/0x13f0
[  166.504313]        lock_acquire+0xb5/0x210
[  168.778973]        process_one_work+0x1b9/0x720
[  171.030316]        worker_thread+0x4c/0x440
[  173.257184]        kthread+0x154/0x190
[  175.456143]        ret_from_fork+0x27/0x40
[  177.624348]
[  177.624348] -> #1 ("kacpi_notify"){+.+.}:
[  181.850351]        __lock_acquire+0x1255/0x13f0
[  183.941695]        lock_acquire+0xb5/0x210
[  186.046115]        flush_workqueue+0xdd/0x510
[  190.408153]        acpi_os_wait_events_complete+0x31/0x40
[  192.625303]        acpi_remove_notify_handler+0x133/0x188
[  194.820829]        acpi_remove_pm_notifier+0x56/0x90
[  196.989068]        acpi_dev_pm_detach+0x5f/0xa0
[  199.145866]        dev_pm_domain_detach+0x27/0x30
[  201.285614]        i2c_device_probe+0x100/0x210
[  203.411118]        driver_probe_device+0x23e/0x310
[  205.522425]        __driver_attach+0xa3/0xb0
[  207.634268]        bus_for_each_dev+0x69/0xa0
[  209.714797]        driver_attach+0x1e/0x20
[  211.778258]        bus_add_driver+0x1bc/0x230
[  213.837162]        driver_register+0x60/0xe0
[  215.868162]        i2c_register_driver+0x42/0x70
[  217.869551]        0xffffffffa0172017
[  219.863009]        do_one_initcall+0x45/0x170
[  221.843863]        do_init_module+0x5f/0x204
[  223.817915]        load_module+0x225b/0x29b0
[  225.757234]        SyS_finit_module+0xc6/0xd0
[  227.661851]        do_syscall_64+0x5c/0x120
[  229.536819]        return_from_SYSCALL_64+0x0/0x7a
[  231.392444]
[  231.392444] -> #0 (acpi_pm_notifier_lock){+.+.}:
[  235.124914]        check_prev_add+0x44e/0x8a0
[  237.024795]        __lock_acquire+0x1255/0x13f0
[  238.937351]        lock_acquire+0xb5/0x210
[  240.840799]        __mutex_lock+0x75/0x940
[  242.709517]        mutex_lock_nested+0x1c/0x20
[  244.551478]        acpi_pm_notify_handler+0x2f/0x80
[  246.382052]        acpi_ev_notify_dispatch+0x44/0x5c
[  248.194412]        acpi_os_execute_deferred+0x14/0x30
[  250.003925]        process_one_work+0x1ec/0x720
[  251.803191]        worker_thread+0x4c/0x440
[  253.605307]        kthread+0x154/0x190
[  255.387498]        ret_from_fork+0x27/0x40
[  257.153175]
[  257.153175] other info that might help us debug this:
[  257.153175]
[  262.324392] Chain exists of:
[  262.324392]   acpi_pm_notifier_lock --> "kacpi_notify" --> (&dpc->work)
[  262.324392]
[  267.391997]  Possible unsafe locking scenario:
[  267.391997]
[  270.758262]        CPU0                    CPU1
[  272.431713]        ----                    ----
[  274.060756]   lock((&dpc->work));
[  275.646532]                                lock("kacpi_notify");
[  277.260772]                                lock((&dpc->work));
[  278.839146]   lock(acpi_pm_notifier_lock);
[  280.391902]
[  280.391902]  *** DEADLOCK ***
[  280.391902]
[  284.986385] 2 locks held by kworker/0:2/47:
[  286.524895]  #0:  ("kacpi_notify"){+.+.}, at: [<ffffffff8109ce90>] process_one_work+0x160/0x720
[  288.112927]  #1:  ((&dpc->work)){+.+.}, at: [<ffffffff8109ce90>] process_one_work+0x160/0x720
[  289.727725]

Fixes: c072530f391e (ACPI / PM: Revork the handling of ACPI device wakeup notifications)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/disassembler: increase show_code buffer size

commit b192571d1ae375e0bbe0aa3ccfa1a3c3704454b9 upstream.

Current buffer size of 64 is too small. objdump shows that there are
instructions which would require up to 75 bytes buffer (with current
formating). 128 bytes "ought to be enough for anybody".

Also replaces 8 spaces with a single tab to reduce the memory footprint.

Fixes the following KASAN finding:

BUG: KASAN: stack-out-of-bounds in number+0x3fe/0x538
Write of size 1 at addr 000000005a4a75a0 by task bash/1282

CPU: 1 PID: 1282 Comm: bash Not tainted 4.14.0+ #215
Hardware name: IBM 2964 N96 702 (z/VM 6.4.0)
Call Trace:
([<000000000011eeb6>] show_stack+0x56/0x88)
 [<0000000000e1ce1a>] dump_stack+0x15a/0x1b0
 [<00000000004e2994>] print_address_description+0xf4/0x288
 [<00000000004e2cf2>] kasan_report+0x13a/0x230
 [<0000000000e38ae6>] number+0x3fe/0x538
 [<0000000000e3dfe4>] vsnprintf+0x194/0x948
 [<0000000000e3ea42>] sprintf+0xa2/0xb8
 [<00000000001198dc>] print_insn+0x374/0x500
 [<0000000000119346>] show_code+0x4ee/0x538
 [<000000000011f234>] show_registers+0x34c/0x388
 [<000000000011f2ae>] show_regs+0x3e/0xa8
 [<000000000011f502>] die+0x1ea/0x2e8
 [<0000000000138f0e>] do_no_context+0x106/0x168
 [<0000000000139a1a>] do_protection_exception+0x4da/0x7d0
 [<0000000000e55914>] pgm_check_handler+0x16c/0x1c0
 [<000000000090639e>] sysrq_handle_crash+0x46/0x58
([<0000000000000007>] 0x7)
 [<00000000009073fa>] __handle_sysrq+0x102/0x218
 [<0000000000907c06>] write_sysrq_trigger+0xd6/0x100
 [<000000000061d67a>] proc_reg_write+0xb2/0x128
 [<0000000000520be6>] __vfs_write+0xee/0x368
 [<0000000000521222>] vfs_write+0x21a/0x278
 [<000000000052156a>] SyS_write+0xda/0x178
 [<0000000000e555cc>] system_call+0xc4/0x270

The buggy address belongs to the page:
page:000003d1016929c0 count:0 mapcount:0 mapping:          (null) index:0x0
flags: 0x0()
raw: 0000000000000000 0000000000000000 0000000000000000 ffffffff00000000
raw: 0000000000000100 0000000000000200 0000000000000000 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
 000000005a4a7480: 00 00 00 00 00 00 00 00 00 00 00 00 f1 f1 f1 f1
 000000005a4a7500: 00 00 00 00 00 00 00 00 f2 f2 f2 f2 00 00 00 00
>000000005a4a7580: 00 00 00 00 f3 f3 f3 f3 00 00 00 00 00 00 00 00
                               ^
 000000005a4a7600: 00 00 00 00 00 00 00 00 00 00 f1 f1 f1 f1 f8 f8
 000000005a4a7680: f2 f2 f2 f2 f2 f2 f8 f8 f2 f2 f3 f3 f3 f3 00 00
==================================================================

Signed-off-by: Vasily Gorbik <gor@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/disassembler: add missing end marker for e7 table

commit 5c50538752af7968f53924b22dede8ed4ce4cb3b upstream.

The e7 opcode table does not have an end marker. Hence when trying to
find an unknown e7 instruction the code will access memory behind the
table until it finds something that matches the opcode, or the kernel
crashes, whatever comes first.

This affects not only the in-kernel disassembler but also uprobes and
kprobes which refuse to set a probe on unknown instructions, and
therefore search the opcode tables to figure out if instructions are
known or not.

Fixes: 3585cb0280654 ("s390/disassembler: add vector instructions")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/guarded storage: fix possible memory corruption

commit fa1edf3f63c05ca8eacafcd7048ed91e5360f1a8 upstream.

For PREEMPT enabled kernels the guarded storage (GS) code contains a
possible use-after-free bug. If a task that makes use of GS exits, it
will execute do_exit() while still enabled for preemption.

That function will call exit_thread_runtime_instr() via exit_thread().
If exit_thread_gs() gets preempted after the GS control block of the
task has been freed but before the pointer to it is set to NULL, then
save_gs_cb(), called from switch_to(), will write to already freed
memory.

Avoid this and simply disable preemption while freeing the control
block and setting the pointer to NULL.

Fixes: 916cda1aa1b4 ("s390: add a system call for guarded storage")
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/runtime instrumention: fix possible memory corruption

commit d6e646ad7cfa7034d280459b2b2546288f247144 upstream.

For PREEMPT enabled kernels the runtime instrumentation (RI) code
contains a possible use-after-free bug. If a task that makes use of RI
exits, it will execute do_exit() while still enabled for preemption.

That function will call exit_thread_runtime_instr() via
exit_thread(). If exit_thread_runtime_instr() gets preempted after the
RI control block of the task has been freed but before the pointer to
it is set to NULL, then save_ri_cb(), called from switch_to(), will
write to already freed memory.

Avoid this and simply disable preemption while freeing the control
block and setting the pointer to NULL.

Fixes: e4b8b3f33fca ("s390: add support for runtime instrumentation")
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/noexec: execute kexec datamover without DAT

commit d0e810eeb3d326978f248b8f0233a2f30f58c72d upstream.

Rebooting into a new kernel with kexec fails (system dies) if tried on
a machine that has no-execute support. Reason for this is that the so
called datamover code gets executed with DAT on (MMU is active) and
the page that contains the datamover is marked as non-executable.
Therefore when branching into the datamover an unexpected program
check happens and afterwards the machine is dead.

This can be simply avoided by disabling DAT, which also disables any
no-execute checks, just before the datamover gets executed.

In fact the first thing done by the datamover is to disable DAT. The
code in the datamover that disables DAT can be removed as well.

Thanks to Michael Holzheu and Gerald Schaefer for tracking this down.

Reviewed-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Reviewed-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fixes: 57d7f939e7bd ("s390: add no-execute support")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390: fix transactional execution control register handling

commit a1c5befc1c24eb9c1ee83f711e0f21ee79cbb556 upstream.

Dan Horák reported the following crash related to transactional execution:

User process fault: interruption code 0013 ilc:3 in libpthread-2.26.so[3ff93c00000+1b000]
CPU: 2 PID: 1 Comm: /init Not tainted 4.13.4-300.fc27.s390x #1
Hardware name: IBM 2827 H43 400 (z/VM 6.4.0)
task: 00000000fafc8000 task.stack: 00000000fafc4000
User PSW : 0705200180000000 000003ff93c14e70
           R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:1 AS:0 CC:2 PM:0 RI:0 EA:3
User GPRS: 0000000000000077 000003ff00000000 000003ff93144d48 000003ff93144d5e
           0000000000000000 0000000000000002 0000000000000000 000003ff00000000
           0000000000000000 0000000000000418 0000000000000000 000003ffcc9fe770
           000003ff93d28f50 000003ff9310acf0 000003ff92b0319a 000003ffcc9fe6d0
User Code: 000003ff93c14e62: 60e0b030            std     %f14,48(%r11)
           000003ff93c14e66: 60f0b038            std     %f15,56(%r11)
          #000003ff93c14e6a: e5600000ff0e        tbegin  0,65294
          >000003ff93c14e70: a7740006            brc     7,3ff93c14e7c
           000003ff93c14e74: a7080000            lhi     %r0,0
           000003ff93c14e78: a7f40023            brc     15,3ff93c14ebe
           000003ff93c14e7c: b2220000            ipm     %r0
           000003ff93c14e80: 8800001c            srl     %r0,28

There are several bugs with control register handling with respect to
transactional execution:

- on task switch update_per_regs() is only called if the next task has
  an mm (is not a kernel thread). This however is incorrect. This
  breaks e.g. for user mode helper handling, where the kernel creates
  a kernel thread and then execve's a user space program. Control
  register contents related to transactional execution won't be
  updated on execve. If the previous task ran with transactional
  execution disabled then the new task will also run with
  transactional execution disabled, which is incorrect. Therefore call
  update_per_regs() unconditionally within switch_to().

- on startup the transactional execution facility is not enabled for
  the idle thread. This is not really a bug, but an inconsistency to
  other facilities. Therefore enable the facility if it is available.

- on fork the new thread's per_flags field is not cleared. This means
  that a child process inherits the PER_FLAG_NO_TE flag. This flag can
  be set with a ptrace request to disable transactional execution for
  the current process. It should not be inherited by new child
  processes in order to be consistent with the handling of all other
  PER related debugging options. Therefore clear the per_flags field in
  copy_thread_tls().

Reported-and-tested-by: Dan Horák <dan@danny.cz>
Fixes: d35339a42dd1 ("s390: add support for transactional memory")
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.14.2

ipmi: Prefer ACPI system interfaces over SMBIOS ones

commit 7e030d6dff713250c7dcfb543cad2addaf479b0e upstream.

The recent changes to add SMBIOS (DMI) IPMI interfaces as platform
devices caused DMI to be selected before ACPI, causing ACPI type
of operations to not work.

Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

coda: fix 'kernel memory exposure attempt' in fsync

commit d337b66a4c52c7b04eec661d86c2ef6e168965a2 upstream.

When an application called fsync on a file in Coda a small request with
just the file identifier was allocated, but the declared length was set
to the size of union of all possible upcall requests.

This bug has been around for a very long time and is now caught by the
extra checking in usercopy that was introduced in Linux-4.8.

The exposure happens when the Coda cache manager process reads the fsync
upcall request at which point it is killed. As a result there is nobody
servicing any further upcalls, trapping any processes that try to access
the mounted Coda filesystem.

Signed-off-by: Jan Harkes <jaharkes@cs.cmu.edu>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/page_ext.c: check if page_ext is not prepared

commit e492080e640c2d1235ddf3441cae634cfffef7e1 upstream.

online_page_ext() and page_ext_init() allocate page_ext for each
section, but they do not allocate if the first PFN is !pfn_present(pfn)
or !pfn_valid(pfn).  Then section->page_ext remains as NULL.
lookup_page_ext checks NULL only if CONFIG_DEBUG_VM is enabled.  For a
valid PFN, __set_page_owner will try to get page_ext through
lookup_page_ext.  Without CONFIG_DEBUG_VM lookup_page_ext will misuse
NULL pointer as value 0.  This incurrs invalid address access.

This is the panic example when PFN 0x100000 is not valid but PFN
0x13FC00 is being used for page_ext.  section->page_ext is NULL,
get_entry returned invalid page_ext address as 0x1DFA000 for a PFN
0x13FC00.

To avoid this panic, CONFIG_DEBUG_VM should be removed so that page_ext
will be checked at all times.

  Unable to handle kernel paging request at virtual address 01dfa014
  ------------[ cut here ]------------
  Kernel BUG at ffffff80082371e0 [verbose debug info unavailable]
  Internal error: Oops: 96000045 [#1] PREEMPT SMP
  Modules linked in:
  PC is at __set_page_owner+0x48/0x78
  LR is at __set_page_owner+0x44/0x78
    __set_page_owner+0x48/0x78
    get_page_from_freelist+0x880/0x8e8
    __alloc_pages_nodemask+0x14c/0xc48
    __do_page_cache_readahead+0xdc/0x264
    filemap_fault+0x2ac/0x550
    ext4_filemap_fault+0x3c/0x58
    __do_fault+0x80/0x120
    handle_mm_fault+0x704/0xbb0
    do_page_fault+0x2e8/0x394
    do_mem_abort+0x88/0x124

Pre-4.7 kernels also need commit f86e4271978b ("mm: check the return
value of lookup_page_ext for all call sites").

Link: http://lkml.kernel.org/r/20171107094131.14621-1-jaewon31.kim@samsung.com
Fixes: eefa864b701d ("mm/page_ext: resurrect struct page extending code for debugging")
Signed-off-by: Jaewon Kim <jaewon31.kim@samsung.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/page_alloc.c: broken deferred calculation

commit d135e5750205a21a212a19dbb05aeb339e2cbea7 upstream.

In reset_deferred_meminit() we determine number of pages that must not
be deferred.  We initialize pages for at least 2G of memory, but also
pages for reserved memory in this node.

The reserved memory is determined in this function:
memblock_reserved_memory_within(), which operates over physical
addresses, and returns size in bytes.  However, reset_deferred_meminit()
assumes that that this function operates with pfns, and returns page
count.

The result is that in the best case machine boots slower than expected
due to initializing more pages than needed in single thread, and in the
worst case panics because fewer than needed pages are initialized early.

Link: http://lkml.kernel.org/r/20171021011707.15191-1-pasha.tatashin@oracle.com
Fixes: 864b9a393dcb ("mm: consider memblock reservations for deferred memory initialization sizing")
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipmi: fix unsigned long underflow

commit 392a17b10ec4320d3c0e96e2a23ebaad1123b989 upstream.

When I set the timeout to a specific value such as 500ms, the timeout
event will not happen in time due to the overflow in function
check_msg_timeout:
...
ent->timeout -= timeout_period;
if (ent->timeout > 0)
return;
...

The type of timeout_period is long, but ent->timeout is unsigned long.
This patch makes the type consistent.

Reported-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ocfs2: should wait dio before inode lock in ocfs2_setattr()

commit 28f5a8a7c033cbf3e32277f4cc9c6afd74f05300 upstream.

we should wait dio requests to finish before inode lock in
ocfs2_setattr(), otherwise the following deadlock will happen:

process 1                  process 2                    process 3
truncate file 'A'          end_io of writing file 'A'   receiving the bast messages
ocfs2_setattr
 ocfs2_inode_lock_tracker
  ocfs2_inode_lock_full
 inode_dio_wait
  __inode_dio_wait
  -->waiting for all dio
  requests finish
                                                        dlm_proxy_ast_handler
                                                         dlm_do_local_bast
                                                          ocfs2_blocking_ast
                                                           ocfs2_generic_handle_bast
                                                            set OCFS2_LOCK_BLOCKED flag
                        dio_end_io
                         dio_bio_end_aio
                          dio_complete
                           ocfs2_dio_end_io
                            ocfs2_dio_end_io_write
                             ocfs2_inode_lock
                              __ocfs2_cluster_lock
                               ocfs2_wait_for_mask
                               -->waiting for OCFS2_LOCK_BLOCKED
                               flag to be cleared, that is waiting
                               for 'process 1' unlocking the inode lock
                           inode_dio_end
                           -->here dec the i_dio_count, but will never
                           be called, so a deadlock happened.

Link: http://lkml.kernel.org/r/59F81636.70508@huawei.com
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Reviewed-by: Jun Piao <piaojun@huawei.com>
Reviewed-by: Joseph Qi <jiangqi903@gmail.com>
Acked-by: Changwei Ge <ge.changwei@h3c.com>
Cc: Mark Fasheh <mfasheh@versity.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ocfs2: fix cluster hang after a node dies

commit 1c01967116a678fed8e2c68a6ab82abc8effeddc upstream.

When a node dies, other live nodes have to choose a new master for an
existed lock resource mastered by the dead node.

As for ocfs2/dlm implementation, this is done by function -
dlm_move_lockres_to_recovery_list which marks those lock rsources as
DLM_LOCK_RES_RECOVERING and manages them via a list from which DLM
changes lock resource's master later.

So without invoking dlm_move_lockres_to_recovery_list, no master will be
choosed after dlm recovery accomplishment since no lock resource can be
found through ::resource list.

What's worse is that if DLM_LOCK_RES_RECOVERING is not marked for lock
resources mastered a dead node, it will break up synchronization among
nodes.

So invoke dlm_move_lockres_to_recovery_list again.

Fixs: 'commit ee8f7fcbe638 ("ocfs2/dlm: continue to purge recovery lockres when recovery master goes down")'
Link: http://lkml.kernel.org/r/63ADC13FD55D6546B7DECE290D39E373CED6E0F9@H3CMLB14-EX.srv.huawei-3com.com
Signed-off-by: Changwei Ge <ge.changwei@h3c.com>
Reported-by: Vitaly Mayatskih <v.mayatskih@gmail.com>
Tested-by: Vitaly Mayatskikh <v.mayatskih@gmail.com>
Cc: Mark Fasheh <mfasheh@versity.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <jiangqi903@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/pagewalk.c: report holes in hugetlb ranges

commit 373c4557d2aa362702c4c2d41288fb1e54990b7c upstream.

This matters at least for the mincore syscall, which will otherwise copy
uninitialized memory from the page allocator to userspace.  It is
probably also a correctness error for /proc/$pid/pagemap, but I haven't
tested that.

Removing the `walk->hugetlb_entry` condition in walk_hugetlb_range() has
no effect because the caller already checks for that.

This only reports holes in hugetlb ranges to callers who have specified
a hugetlb_entry callback.

This issue was found using an AFL-based fuzzer.

v2:
 - don't crash on ->pte_hole==NULL (Andrew Morton)
 - add Cc stable (Andrew Morton)

Fixes: 1e25a271c8ac ("mincore: apply page table walker on do_mincore()")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rcu: Fix up pending cbs check in rcu_prepare_for_idle

commit 135bd1a230bb69a68c9808a7d25467318900b80a upstream.

The pending-callbacks check in rcu_prepare_for_idle() is backwards.
It should accelerate if there are pending callbacks, but the check
rather uselessly accelerates only if there are no callbacks.  This commit
therefore inverts this check.

Fixes: 15fecf89e46a ("srcu: Abstract multi-tail callback list handling")
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tpm-dev-common: Reject too short writes

commit ee70bc1e7b63ac8023c9ff9475d8741e397316e7 upstream.

tpm_transmit() does not offer an explicit interface to indicate the number
of valid bytes in the communication buffer. Instead, it relies on the
commandSize field in the TPM header that is encoded within the buffer.
Therefore, ensure that a) enough data has been written to the buffer, so
that the commandSize field is present and b) the commandSize field does not
announce more data than has been written to the buffer.

This should have been fixed with CVE-2011-1161 long ago, but apparently
a correct version of that patch never made it into the kernel.

Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_fintek: Fix finding base_port with activated SuperIO

commit fd97e66c5529046e989a0879c3bb58fddb592c71 upstream.

The SuperIO will be configured at boot time by BIOS, but some BIOS
will not deactivate the SuperIO when the end of configuration. It'll
lead to mismatch for pdata->base_port in probe_setup_port(). So we'll
deactivate all SuperIO before activate special base_port in
fintek_8250_enter_key().

Tested on iBASE MI802.

Tested-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Reviewd-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: omap: Fix EFR write on RTS deassertion

commit 2a71de2f7366fb1aec632116d0549ec56d6a3940 upstream.

Commit 348f9bb31c56 ("serial: omap: Fix RTS handling") sought to enable
auto RTS upon manual RTS assertion and disable it on deassertion.
However it seems the latter was done incorrectly, it clears all bits in
the Extended Features Register *except* auto RTS.

Fixes: 348f9bb31c56 ("serial: omap: Fix RTS handling")
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ima: do not update security.ima if appraisal status is not INTEGRITY_PASS

commit 020aae3ee58c1af0e7ffc4e2cc9fe4dc630338cb upstream.

Commit b65a9cfc2c38 ("Untangling ima mess, part 2: deal with counters")
moved the call of ima_file_check() from may_open() to do_filp_open() at a
point where the file descriptor is already opened.

This breaks the assumption made by IMA that file descriptors being closed
belong to files whose access was granted by ima_file_check(). The
consequence is that security.ima and security.evm are updated with good
values, regardless of the current appraisal status.

For example, if a file does not have security.ima, IMA will create it after
opening the file for writing, even if access is denied. Access to the file
will be allowed afterwards.

Avoid this issue by checking the appraisal status before updating
security.ima.

Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/sctp: Always set scope_id in sctp_inet6_skb_msgname

[ Upstream commit 7c8a61d9ee1df0fb4747879fa67a99614eb62fec ]

Alexandar Potapenko while testing the kernel with KMSAN and syzkaller
discovered that in some configurations sctp would leak 4 bytes of
kernel stack.

Working with his reproducer I discovered that those 4 bytes that
are leaked is the scope id of an ipv6 address returned by recvmsg.

With a little code inspection and a shrewd guess I discovered that
sctp_inet6_skb_msgname only initializes the scope_id field for link
local ipv6 addresses to the interface index the link local address
pertains to instead of initializing the scope_id field for all ipv6
addresses.

That is almost reasonable as scope_id's are meaniningful only for link
local addresses.  Set the scope_id in all other cases to 0 which is
not a valid interface index to make it clear there is nothing useful
in the scope_id field.

There should be no danger of breaking userspace as the stack leak
guaranteed that previously meaningless random data was being returned.

Fixes: 372f525b495c ("SCTP:  Resync with LKSCTP tree.")
History-tree: https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Reported-by: Alexander Potapenko <glider@google.com>
Tested-by: Alexander Potapenko <glider@google.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fealnx: Fix building error on MIPS

[ Upstream commit cc54c1d32e6a4bb3f116721abf900513173e4d02 ]

This patch try to fix the building error on MIPS. The reason is MIPS
has already defined the LONG macro, which conflicts with the LONG enum
in drivers/net/ethernet/fealnx.c.

Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: cdc_ncm: GetNtbFormat endian fix

[ Upstream commit 6314dab4b8fb8493d810e175cb340376052c69b6 ]

The GetNtbFormat and SetNtbFormat requests operate on 16 bit little
endian values. We get away with ignoring this most of the time, because
we only care about USB_CDC_NCM_NTB16_FORMAT which is 0x0000.  This
fails for USB_CDC_NCM_NTB32_FORMAT.

Fix comparison between LE value from device and constant by converting
the constant to LE.

Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Fixes: 2b02c20ce0c2 ("cdc_ncm: Set NTB format again after altsetting switch for Huawei devices")
Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Cc: Christian Panton <christian@panton.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-By: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vxlan: fix the issue that neigh proxy blocks all icmpv6 packets

[ Upstream commit 8bff3685a4bbf175a96bc6a528f13455d8d38244 ]

Commit f1fb08f6337c ("vxlan: fix ND proxy when skb doesn't have transport
header offset") removed icmp6_code and icmp6_type check before calling
neigh_reduce when doing neigh proxy.

It means all icmpv6 packets would be blocked by this, not only ns packet.
In Jianlin's env, even ping6 couldn't work through it.

This patch is to bring the icmp6_code and icmp6_type check back and also
removed the same check from neigh_reduce().

Fixes: f1fb08f6337c ("vxlan: fix ND proxy when skb doesn't have transport header offset")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Vincent Bernat <vincent@bernat.im>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

af_netlink: ensure that NLMSG_DONE never fails in dumps

[ Upstream commit 0642840b8bb008528dbdf929cec9f65ac4231ad0 ]

The way people generally use netlink_dump is that they fill in the skb
as much as possible, breaking when nla_put returns an error. Then, they
get called again and start filling out the next skb, and again, and so
forth. The mechanism at work here is the ability for the iterative
dumping function to detect when the skb is filled up and not fill it
past the brim, waiting for a fresh skb for the rest of the data.

However, if the attributes are small and nicely packed, it is possible
that a dump callback function successfully fills in attributes until the
skb is of size 4080 (libmnl's default page-sized receive buffer size).
The dump function completes, satisfied, and then, if it happens to be
that this is actually the last skb, and no further ones are to be sent,
then netlink_dump will add on the NLMSG_DONE part:

  nlh = nlmsg_put_answer(skb, cb, NLMSG_DONE, sizeof(len), NLM_F_MULTI);

It is very important that netlink_dump does this, of course. However, in
this example, that call to nlmsg_put_answer will fail, because the
previous filling by the dump function did not leave it enough room. And
how could it possibly have done so? All of the nla_put variety of
functions simply check to see if the skb has enough tailroom,
independent of the context it is in.

In order to keep the important assumptions of all netlink dump users, it
is therefore important to give them an skb that has this end part of the
tail already reserved, so that the call to nlmsg_put_answer does not
fail. Otherwise, library authors are forced to find some bizarre sized
receive buffer that has a large modulo relative to the common sizes of
messages received, which is ugly and buggy.

This patch thus saves the NLMSG_DONE for an additional message, for the
case that things are dangerously close to the brim. This requires
keeping track of the errno from ->dump() across calls.

Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bio: ensure __bio_clone_fast copies bi_partno

commit 62530ed8b1d07a45dec94d46e521c0c6c2d476e6 upstream.

A new field was introduced in 74d46992e0d9, bi_partno, instead of using
bdev->bd_contains and encoding the partition information in the bi_bdev
field.  __bio_clone_fast was changed to copy the disk information, but
not the partition information.  At minimum, this regressed bcache and
caused data corruption.

Signed-off-by: Michael Lyle <mlyle@lyle.org>
Fixes: 74d46992e0d9 ("block: replace bi_bdev with a gendisk pointer and partitions index")
Reported-by: Pavel Goran <via-bcache@pvgoran.name>
Reported-by: Campbell Steven <casteven@gmail.com>
Reviewed-by: Coly Li <colyli@suse.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.14.1

sparc64: Fix page table walk for PUD hugepages

[ Upstream commit 70f3c8b7c2e7ebcdde8354da004872e7c9184e97 ]

For a PUD hugepage entry, we need to propagate bits [32:22]
from virtual address to resolve at 4M granularity. However,
the current code was incorrectly propagating bits [29:19].
This bug can cause incorrect data to be returned for pages
backed with 16G hugepages.

Signed-off-by: Nitin Gupta <nitin.m.gupta@oracle.com>
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sparc64: mmu_context: Add missing include files

commit 01c3f0a42a2a0ff0c3fed80a1a25f2641ae72554 upstream.

Fix the following build errors.

In file included from arch/sparc/include/asm/mmu_context.h:4:0,
                 from include/linux/mmu_context.h:4,
 from drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd.h:29,
 from drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd.c:23:
arch/sparc/include/asm/mmu_context_64.h:22:37: error:
unknown type name 'per_cpu_secondary_mm'

arch/sparc/include/asm/mmu_context_64.h: In function 'switch_mm':
arch/sparc/include/asm/mmu_context_64.h:79:2: error:
implicit declaration of function 'smp_processor_id'

Fixes: 70539bd79500 ("drm/amd: Update MEC HQD loading code for KFD")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sparc32: Add cmpxchg64().

commit 23198ddffb6cddb5d5824230af4dd4b46e4046a4 upstream.

This fixes the build with i40e driver enabled.

Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: fix use-after-free at controller deregistration

commit 67f7b2781fafcc0f52464880154b320fea1ae982 upstream.

The controller is typically freed as part of device_unregister() so
store the bus id before deregistration to avoid use-after-free when the
id is later released.

Fixes: 9b61e302210e ("spi: Pick spi bus number from Linux idr or spi alias")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: Revert 4 commits breaking ARP

commit 66d32fdcbf03851724a8b551d490ae1ddfe6eef2 upstream.

Commit 2ba8444c97b1 ("staging:r8188eu: move IV/ICV trimming into
decrypt() and also place it after rtl88eu_mon_recv_hook()") breaks ARP.

After this commit ssh-ing to a laptop with r8188eu wifi no longer works
if the machine connecting has never communicated with the laptop before.
This is 100% reproducable using "arp -d <ipv4> && ssh <ipv4>" to ssh to
a laptop with r8188eu wifi.

This commit reverts 4 commits in total:

1. Commit 79650ffde38e ("staging:r8188eu: trim IV/ICV fields in
   validate_recv_data_frame()")
This commit depends on 2 of the other commits being reverted.

2. Commit 02b19b4c4920 ("staging:r8188eu: inline unprotect_frame() in
   mon_recv_decrypted_recv()")
The inline code is wrong the un-inlined version contains:
if (skb->len < hdr_len + iv_len + icv_len)
return;
...
Where as the inline-ed code introduced by this commit does:
if (skb->len < hdr_len + iv_len + icv_len) {
...
Note the same check, but now to actually continue doing ... instead
of to not do it, so this commit is no good.

3. Commit d86e16da6a5d ("staging:r8188eu: use different mon_recv_decrypted()
   inside rtl88eu_mon_recv_hook() and rtl88eu_mon_xmit_hook().")
This commit introduced a 1:1 copy of a function so that one of the
2 copies can be modified in the 2 commits we're already reverting.

4. Commit 2ba8444c97b1 ("staging:r8188eu: move IV/ICV trimming into
   decrypt() and also place it after rtl88eu_mon_recv_hook()")
This is the commit actually breaking ARP.

Note this commit is a straight-forward squash of the revert of these
4 commits, without any changes.

Cc: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: vboxvideo: Fix reporting invalid suggested-offset-properties

commit ce10d7b4e8e3574b9616e54a09d64521b9aeb8b6 upstream.

The x and y hints receives from the host are unsigned 32 bit integers and
they get set to -1 (0xffffffff) when invalid. Before this commit the
vboxvideo driver was storing them in an u16 causing the -1 to be truncated
to 65535 which, once reported to userspace, was breaking gnome 3.26+
in Wayland mode.

This commit stores the host values in 32 bit variables, removing the
truncation and checks for -1, replacing it with 0 as -1 is not a valid
suggested-offset-property value. Likewise the properties are now
initialized to 0 instead of -1, since -1 is not a valid value.
This fixes gnome 3.26+ in Wayland mode not working with the vboxvideo
driver.

Reported-by: Gianfranco Costamagna <locutusofborg@debian.org>
Cc: Michael Thayer <michael.thayer@oracle.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: greybus: spilib: fix use-after-free after deregistration

commit 770b03c2ca4aa44d226cf248f86aa23e546147d0 upstream.

Remove erroneous spi_master_put() after controller deregistration which
would access the already freed spi controller.

Note that spi_unregister_master() drops our only controller reference.

Fixes: ba3e67001b42 ("greybus: SPI: convert to a gpbridge driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: ccree: fix 64 bit scatter/gather DMA ops

commit e0b3f39092a1cff5548cbaf40096ec25e7721de6 upstream.

Fix a wrong offset used in splitting a 64 DMA address to MSB/LSB
parts needed for scatter/gather HW descriptors causing operations
relying on them to fail on 64 bit platforms.

Fixes: c6f7f2f4591f ("staging: ccree: refactor LLI access macros")
Reported-by: Stuart Yoder <stuart.yoder@arm.com>
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: sm750fb: Fix parameter mistake in poke32

commit 16808dcf605e6302319a8c3266789b76d4c0983b upstream.

In commit c075b6f2d357ea9 ("staging: sm750fb: Replace POKE32 and PEEK32
by inline functions"), POKE32 has been replaced by the inline function
poke32. But it exchange the "addr" and "data" parameters by mistake, so
fix it.

Fixes: c075b6f2d357ea9 ("staging: sm750fb: Replace POKE32 and PEEK32 by inline functions"),
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Liangliang Huang <huangll@lemote.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: Fix bssid buffer offset in Txq

commit 1bbf6a6d4091affb27ec0a19d7aa7887ce72f610 upstream.

Commit 46949b48568b ("staging: wilc1000: New cfg packet
format in handle_set_wfi_drv_handler") updated the frame
format sent from host to the firmware. The code to update
the bssid offset in the new frame was part of a second
patch in the series which did not make it in and thus
causes connection problems after associating to an AP.

This fix adds the proper offset of the bssid value in the
Tx queue buffer to fix the connection issues.

Fixes: 46949b48568b ("staging: wilc1000: New cfg packet format in handle_set_wfi_drv_handler")
Signed-off-by: Aditya Shankar <Aditya.Shankar@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rpmsg: glink: Add missing MODULE_LICENSE

commit 1e0d5615bbc37deb7732491798abccf8d3c3d244 upstream.

The qcom_glink_native driver is missing a MODULE_LICENSE(), correct
this.

Fixes: 835764ddd9af ("rpmsg: glink: Move the common glink protocol implementation to glink_native.c")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: wacom: generic: Recognize WACOM_HID_WD_PEN as a type of pen collection

commit 885e89f601a52cc6fb025b009df58ba83d142734 upstream.

The WACOM_PEN_FIELD macro is used to determine if a given HID field should be
associated with pen input. This field includes several known collection types
that Wacom pen data is contained in, but the WACOM_HID_WD_PEN application
collection type is notably missing. This can result in fields within this
kind of collection being completely ignored by the `wacom_usage_mapping`
function, preventing the later '*_event' functions from being notified about
changes to their value.

Fixes: c9c095874a ("HID: wacom: generic: Support and use 'Custom HID' mode and usages")
Fixes: ac2423c975 ("HID: wacom: generic: add vendor defined touch")
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: cp2112: add HIDRAW dependency

commit cde3076bdc38bf436e517a379759a9092c6ffd4f upstream.

Otherwise, with HIDRAW=n, the probe function crashes because of null
dereference of hdev->hidraw.

Fixes: 42cb6b35b9e6 ("HID: cp2112: use proper hidraw name with minor number")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

platform/x86: peaq_wmi: Fix missing terminating entry for peaq_dmi_table

commit d6fa71f1c003fb2bc824276bb424a4171f9a717f upstream.

Add missing terminating entry to peaq_dmi_table.

Fixes: 3b95206110a2 ("platform/x86: peaq-wmi: Add DMI check before ...")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

platform/x86: peaq-wmi: Add DMI check before binding to the WMI interface

commit 3b95206110a2c13076c3a7fa8ddeae36c2dbcf42 upstream.

It seems that the WMI GUID used by the PEAQ 2-in-1 WMI hotkeys is not
as unique as a GUID should be and is used on some other devices too.

This is causing spurious key-press reports on these other devices.

This commits adds a DMI check to the PEAQ 2-in-1 WMI hotkeys driver to
ensure that it is actually running on a PEAQ 2-in-1, fixing the
spurious key-presses on these other devices.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1497861
BugLink: https://bugzilla.suse.com/attachment.cgi?id=743182
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/MCE/AMD: Always give panic severity for UC errors in kernel context

commit d65dfc81bb3894fdb68cbc74bbf5fb48d2354071 upstream.

The AMD severity grading function was introduced in kernel 4.1. The
current logic can possibly give MCE_AR_SEVERITY for uncorrectable
errors in kernel context. The system may then get stuck in a loop as
memory_failure() will try to handle the bad kernel memory and find it
busy.

Return MCE_PANIC_SEVERITY for all UC errors IN_KERNEL context on AMD
systems.

After:

  b2f9d678e28c ("x86/mce: Check for faults tagged in EXTABLE_CLASS_FAULT exception table entries")

was accepted in v4.6, this issue was masked because of the tail-end attempt
at kernel mode recovery in the #MC handler.

However, uncorrectable errors IN_KERNEL context should always be considered
unrecoverable and cause a panic.

Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Fixes: bf80bbd7dcf5 (x86/mce: Add an AMD severities-grading function)
Link: http://lkml.kernel.org/r/20171106174633.13576-1-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests/x86/protection_keys: Fix syscall NR redefinition warnings

commit 693cb5580fdb026922363aa103add64b3ecd572e upstream.

On new enough glibc, the pkey syscalls numbers are available.  Check
first before defining them to avoid warnings like:

protection_keys.c:198:0: warning: "SYS_pkey_alloc" redefined

Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bpetkov@suse.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1fbef53a9e6befb7165ff855fc1a7d4788a191d6.1509794321.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: garmin_gps: fix memory leak on probe errors

commit 74d471b598444b7f2d964930f7234779c80960a0 upstream.

Make sure to free the port private data before returning after a failed
probe attempt.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: garmin_gps: fix I/O after failed probe and remove

commit 19a565d9af6e0d828bd0d521d3bafd5017f4ce52 upstream.

Make sure to stop any submitted interrupt and bulk-out URBs before
returning after failed probe and when the port is being unbound to avoid
later NULL-pointer dereferences in the completion callbacks.

Also fix up the related and broken I/O cancellation on failed open and
on close. (Note that port->write_urb was never submitted.)

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: qcserial: add pid/vid for Sierra Wireless EM7355 fw update

commit 771394a54148f18926ca86414e51c69eda27d0cd upstream.

Add USB PID/VID for Sierra Wireless EM7355 LTE modem QDL firmware update
mode.

Signed-off-by: Douglas Fischer <douglas.fischer@outlook.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: Change DbC debug device binding ID

commit 12f28144cf2cf69e1520e238eee7c384719ca44b upstream.

The product ID for "Linux USB GDB Target device" has been
changed. Change the driver binding table accordingly.

This patch should be back-ported to kernels as old as v4.12,
that contain the commit 57fb47279a04 ("usb/serial: Add DBC
debug device support to usb_debug").

Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: metro-usb: stop I/O after failed open

commit 2339536d229df25c71c0900fc619289229bfecf6 upstream.

Make sure to kill the interrupt-in URB after a failed open request.
Apart from saving power (and avoiding stale input after a later
successful open), this also prevents a NULL-deref in the completion
handler if the port is manually unbound.

Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 704577861d5e ("USB: serial: metro-usb: get data from device in Uni-Directional mode.")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: f_fs: Fix use-after-free in ffs_free_inst

commit cdafb6d8b8da7fde266f79b3287ac221aa841879 upstream.

KASAN enabled configuration reports an error

BUG: KASAN: use-after-free in ffs_free_inst+... [usb_f_fs] at addr ...
Write of size 8 by task ...

This is observed after "ffs-test" is run and interrupted. If after that
functionfs is unmounted and g_ffs module is unloaded, that use-after-free
occurs during g_ffs module removal.

Although the report indicates ffs_free_inst() function, the actual
use-after-free condition occurs in _ffs_free_dev() function, which
is probably inlined into ffs_free_inst().

This happens due to keeping the ffs_data reference in device structure
during functionfs unmounting, while ffs_data itself is freed as no longer
needed. The fix is to clear that reference in ffs_closed() function,
which is a counterpart of ffs_ready(), where the reference is stored.

Fixes: 3262ad824307 ("usb: gadget: f_fs: Stop ffs_closed NULL pointer dereference")
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: Add delay-init quirk for Corsair K70 LUX keyboards

commit a0fea6027f19c62727315aba1a7fae75a9caa842 upstream.

Without this patch, K70 LUX keyboards don't work, saying
usb 3-3: unable to read config index 0 descriptor/all
usb 3-3: can't read configurations, error -110
usb usb3-port3: unable to enumerate USB device

Signed-off-by: Bernhard Rosenkraenzer <Bernhard.Rosenkranzer@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usbfs: compute urb->actual_length for isochronous

commit 2ef47001b3ee3ded579b7532ebdcf8680e4d8c54 upstream.

The USB kerneldoc says that the actual_length field "is read in
non-iso completion functions", but the usbfs driver uses it for all
URB types in processcompl().  Since not all of the host controller
drivers set actual_length for isochronous URBs, programs using usbfs
with some host controllers don't work properly.  For example, Minas
reports that a USB camera controlled by libusb doesn't work properly
with a dwc2 controller.

It doesn't seem worthwhile to change the HCDs and the documentation,
since the in-kernel USB class drivers evidently don't rely on
actual_length for isochronous transfers.  The easiest solution is for
usbfs to calculate the actual_length value for itself, by adding up
the lengths of the individual packets in an isochronous transfer.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Reported-and-tested-by: wlf <wulf@rock-chips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: early: Use new USB product ID and strings for DbC device

commit c67678ec78eff9cf1e7e997fe6c37c9fcccfc5b8 upstream.

The DbC register set defines an interface for system software
to specify the vendor id and product id for the debug device.
These two values will be presented by the debug device in its
device descriptor idVendor and idProduct fields.

The current used product ID is a place holder. We now have a
valid one. The description strings are changed accordingly.

This patch should be back-ported to kernels as old as v4.12,
that contain the commit aeb9dd1de98c ("usb/early: Add driver
for xhci debug capability").

Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: brcm - Explicity ACK mailbox message

commit f0e2ce58f853634d7ad1a418a49bd5fbd556227c upstream.

Add support to explicity ACK mailbox message
because after sending message we can know
the send status via error attribute of brcm_message.

This is needed to support "txdone_ack" supported in
mailbox controller driver.

Fixes: 9d12ba86f818 ("crypto: brcm - Add Broadcom SPU driver")
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Reviewed-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: dh - Don't permit 'key' or 'g' size longer than 'p'

commit ccd9888f14a8019c0bbdeeae758aba1f58693712 upstream.

The "qat-dh" DH implementation assumes that 'key' and 'g' can be copied
into a buffer with size 'p_size'.  However it was never checked that
that was actually the case, which most likely allowed users to cause a
buffer underflow via KEYCTL_DH_COMPUTE.

Fix this by updating crypto_dh_decode_key() to verify this precondition
for all DH implementations.

Fixes: c9839143ebbf ("crypto: qat - Add DH support")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: dh - Don't permit 'p' to be 0

commit 199512b1234f09e44d592153ec82b44212b2f0c4 upstream.

If 'p' is 0 for the software Diffie-Hellman implementation, then
dh_max_size() returns 0.  In the case of KEYCTL_DH_COMPUTE, this causes
ZERO_SIZE_PTR to be passed to sg_init_one(), which with
CONFIG_DEBUG_SG=y triggers the 'BUG_ON(!virt_addr_valid(buf));' in
sg_set_buf().

Fix this by making crypto_dh_decode_key() reject 0 for 'p'.  p=0 makes
no sense for any DH implementation because 'p' is supposed to be a prime
number.  Moreover, 'mod 0' is not mathematically defined.

Bug report:

    kernel BUG at ./include/linux/scatterlist.h:140!
    invalid opcode: 0000 [#1] SMP KASAN
    CPU: 0 PID: 27112 Comm: syz-executor2 Not tainted 4.14.0-rc7-00010-gf5dbb5d0ce32-dirty #7
    Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.3-20171021_125229-anatol 04/01/2014
    task: ffff88006caac0c0 task.stack: ffff88006c7c8000
    RIP: 0010:sg_set_buf include/linux/scatterlist.h:140 [inline]
    RIP: 0010:sg_init_one+0x1b3/0x240 lib/scatterlist.c:156
    RSP: 0018:ffff88006c7cfb08 EFLAGS: 00010216
    RAX: 0000000000010000 RBX: ffff88006c7cfe30 RCX: 00000000000064ee
    RDX: ffffffff81cf64c3 RSI: ffffc90000d72000 RDI: ffffffff92e937e0
    RBP: ffff88006c7cfb30 R08: ffffed000d8f9fab R09: ffff88006c7cfd30
    R10: 0000000000000005 R11: ffffed000d8f9faa R12: ffff88006c7cfd30
    R13: 0000000000000000 R14: 0000000000000010 R15: ffff88006c7cfc50
    FS:  00007fce190fa700(0000) GS:ffff88003ea00000(0000) knlGS:0000000000000000
    CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
    CR2: 00007fffc6b33db8 CR3: 000000003cf64000 CR4: 00000000000006f0
    Call Trace:
     __keyctl_dh_compute+0xa95/0x19b0 security/keys/dh.c:360
     keyctl_dh_compute+0xac/0x100 security/keys/dh.c:434
     SYSC_keyctl security/keys/keyctl.c:1745 [inline]
     SyS_keyctl+0x72/0x2c0 security/keys/keyctl.c:1641
     entry_SYSCALL_64_fastpath+0x1f/0xbe
    RIP: 0033:0x4585c9
    RSP: 002b:00007fce190f9bd8 EFLAGS: 00000216 ORIG_RAX: 00000000000000fa
    RAX: ffffffffffffffda RBX: 0000000000738020 RCX: 00000000004585c9
    RDX: 000000002000d000 RSI: 0000000020000ff4 RDI: 0000000000000017
    RBP: 0000000000000046 R08: 0000000020008000 R09: 0000000000000000
    R10: 0000000000000000 R11: 0000000000000216 R12: 00007fff6e610cde
    R13: 00007fff6e610cdf R14: 00007fce190fa700 R15: 0000000000000000
    Code: 03 0f b6 14 02 48 89 f8 83 e0 07 83 c0 03 38 d0 7c 04 84 d2 75 33 5b 45 89 6c 24 14 41 5c 41 5d 41 5e 41 5f 5d c3 e8 fd 8f 68 ff <0f> 0b e8 f6 8f 68 ff 0f 0b e8 ef 8f 68 ff 0f 0b e8 e8 8f 68 ff 20
    RIP: sg_set_buf include/linux/scatterlist.h:140 [inline] RSP: ffff88006c7cfb08
    RIP: sg_init_one+0x1b3/0x240 lib/scatterlist.c:156 RSP: ffff88006c7cfb08

Fixes: 802c7f1c84e4 ("crypto: dh - Add DH software implementation")
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: dh - Fix double free of ctx->p

commit 12d41a023efb01b846457ccdbbcbe2b65a87d530 upstream.

When setting the secret with the software Diffie-Hellman implementation,
if allocating 'g' failed (e.g. if it was longer than
MAX_EXTERN_MPI_BITS), then 'p' was freed twice: once immediately, and
once later when the crypto_kpp tfm was destroyed.

Fix it by using dh_free_ctx() (renamed to dh_clear_ctx()) in the error
paths, as that correctly sets the pointers to NULL.

KASAN report:

    MPI: mpi too large (32760 bits)
    ==================================================================
    BUG: KASAN: use-after-free in mpi_free+0x131/0x170
    Read of size 4 at addr ffff88006c7cdf90 by task reproduce_doubl/367

    CPU: 1 PID: 367 Comm: reproduce_doubl Not tainted 4.14.0-rc7-00040-g05298abde6fe #7
    Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
    Call Trace:
     dump_stack+0xb3/0x10b
     ? mpi_free+0x131/0x170
     print_address_description+0x79/0x2a0
     ? mpi_free+0x131/0x170
     kasan_report+0x236/0x340
     ? akcipher_register_instance+0x90/0x90
     __asan_report_load4_noabort+0x14/0x20
     mpi_free+0x131/0x170
     ? akcipher_register_instance+0x90/0x90
     dh_exit_tfm+0x3d/0x140
     crypto_kpp_exit_tfm+0x52/0x70
     crypto_destroy_tfm+0xb3/0x250
     __keyctl_dh_compute+0x640/0xe90
     ? kasan_slab_free+0x12f/0x180
     ? dh_data_from_key+0x240/0x240
     ? key_create_or_update+0x1ee/0xb20
     ? key_instantiate_and_link+0x440/0x440
     ? lock_contended+0xee0/0xee0
     ? kfree+0xcf/0x210
     ? SyS_add_key+0x268/0x340
     keyctl_dh_compute+0xb3/0xf1
     ? __keyctl_dh_compute+0xe90/0xe90
     ? SyS_add_key+0x26d/0x340
     ? entry_SYSCALL_64_fastpath+0x5/0xbe
     ? trace_hardirqs_on_caller+0x3f4/0x560
     SyS_keyctl+0x72/0x2c0
     entry_SYSCALL_64_fastpath+0x1f/0xbe
    RIP: 0033:0x43ccf9
    RSP: 002b:00007ffeeec96158 EFLAGS: 00000246 ORIG_RAX: 00000000000000fa
    RAX: ffffffffffffffda RBX: 000000000248b9b9 RCX: 000000000043ccf9
    RDX: 00007ffeeec96170 RSI: 00007ffeeec96160 RDI: 0000000000000017
    RBP: 0000000000000046 R08: 0000000000000000 R09: 0248b9b9143dc936
    R10: 0000000000001000 R11: 0000000000000246 R12: 0000000000000000
    R13: 0000000000409670 R14: 0000000000409700 R15: 0000000000000000

    Allocated by task 367:
     save_stack_trace+0x16/0x20
     kasan_kmalloc+0xeb/0x180
     kmem_cache_alloc_trace+0x114/0x300
     mpi_alloc+0x4b/0x230
     mpi_read_raw_data+0xbe/0x360
     dh_set_secret+0x1dc/0x460
     __keyctl_dh_compute+0x623/0xe90
     keyctl_dh_compute+0xb3/0xf1
     SyS_keyctl+0x72/0x2c0
     entry_SYSCALL_64_fastpath+0x1f/0xbe

    Freed by task 367:
     save_stack_trace+0x16/0x20
     kasan_slab_free+0xab/0x180
     kfree+0xb5/0x210
     mpi_free+0xcb/0x170
     dh_set_secret+0x2d7/0x460
     __keyctl_dh_compute+0x623/0xe90
     keyctl_dh_compute+0xb3/0xf1
     SyS_keyctl+0x72/0x2c0
     entry_SYSCALL_64_fastpath+0x1f/0xbe

Fixes: 802c7f1c84e4 ("crypto: dh - Add DH software implementation")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: dib0700: fix invalid dvb_detach argument

commit eb0c19942288569e0ae492476534d5a485fb8ab4 upstream.

dvb_detach(arg) calls symbol_put_addr(arg), where arg should be a pointer
to a function. Right now a pointer to state->dib7000p_ops is passed to
dvb_detach(), which causes a BUG() in symbol_put_addr() as discovered by
syzkaller. Pass state->dib7000p_ops.set_wbd_ref instead.

------------[ cut here ]------------
kernel BUG at kernel/module.c:1081!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
Modules linked in:
CPU: 1 PID: 1151 Comm: kworker/1:1 Tainted: G        W
4.14.0-rc1-42251-gebb2c2437d80 #224
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
task: ffff88006a336300 task.stack: ffff88006a7c8000
RIP: 0010:symbol_put_addr+0x54/0x60 kernel/module.c:1083
RSP: 0018:ffff88006a7ce210 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff880062a8d190 RCX: 0000000000000000
RDX: dffffc0000000020 RSI: ffffffff85876d60 RDI: ffff880062a8d190
RBP: ffff88006a7ce218 R08: 1ffff1000d4f9c12 R09: 1ffff1000d4f9ae4
R10: 1ffff1000d4f9bed R11: 0000000000000000 R12: ffff880062a8d180
R13: 00000000ffffffed R14: ffff880062a8d190 R15: ffff88006947c000
FS:  0000000000000000(0000) GS:ffff88006c900000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f6416532000 CR3: 00000000632f5000 CR4: 00000000000006e0
Call Trace:
 stk7070p_frontend_attach+0x515/0x610
drivers/media/usb/dvb-usb/dib0700_devices.c:1013
 dvb_usb_adapter_frontend_init+0x32b/0x660
drivers/media/usb/dvb-usb/dvb-usb-dvb.c:286
 dvb_usb_adapter_init drivers/media/usb/dvb-usb/dvb-usb-init.c:86
 dvb_usb_init drivers/media/usb/dvb-usb/dvb-usb-init.c:162
 dvb_usb_device_init+0xf70/0x17f0 drivers/media/usb/dvb-usb/dvb-usb-init.c:277
 dib0700_probe+0x171/0x5a0 drivers/media/usb/dvb-usb/dib0700_core.c:886
 usb_probe_interface+0x35d/0x8e0 drivers/usb/core/driver.c:361
 really_probe drivers/base/dd.c:413
 driver_probe_device+0x610/0xa00 drivers/base/dd.c:557
 __device_attach_driver+0x230/0x290 drivers/base/dd.c:653
 bus_for_each_drv+0x161/0x210 drivers/base/bus.c:463
 __device_attach+0x26e/0x3d0 drivers/base/dd.c:710
 device_initial_probe+0x1f/0x30 drivers/base/dd.c:757
 bus_probe_device+0x1eb/0x290 drivers/base/bus.c:523
 device_add+0xd0b/0x1660 drivers/base/core.c:1835
 usb_set_configuration+0x104e/0x1870 drivers/usb/core/message.c:1932
 generic_probe+0x73/0xe0 drivers/usb/core/generic.c:174
 usb_probe_device+0xaf/0xe0 drivers/usb/core/driver.c:266
 really_probe drivers/base/dd.c:413
 driver_probe_device+0x610/0xa00 drivers/base/dd.c:557
 __device_attach_driver+0x230/0x290 drivers/base/dd.c:653
 bus_for_each_drv+0x161/0x210 drivers/base/bus.c:463
 __device_attach+0x26e/0x3d0 drivers/base/dd.c:710
 device_initial_probe+0x1f/0x30 drivers/base/dd.c:757
 bus_probe_device+0x1eb/0x290 drivers/base/bus.c:523
 device_add+0xd0b/0x1660 drivers/base/core.c:1835
 usb_new_device+0x7b8/0x1020 drivers/usb/core/hub.c:2457
 hub_port_connect drivers/usb/core/hub.c:4903
 hub_port_connect_change drivers/usb/core/hub.c:5009
 port_event drivers/usb/core/hub.c:5115
 hub_event+0x194d/0x3740 drivers/usb/core/hub.c:5195
 process_one_work+0xc7f/0x1db0 kernel/workqueue.c:2119
 worker_thread+0x221/0x1850 kernel/workqueue.c:2253
 kthread+0x3a1/0x470 kernel/kthread.c:231
 ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:431
Code: ff ff 48 85 c0 74 24 48 89 c7 e8 48 ea ff ff bf 01 00 00 00 e8
de 20 e3 ff 65 8b 05 b7 2f c2 7e 85 c0 75 c9 e8 f9 0b c1 ff eb c2 <0f>
0b 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 b8 00 00
RIP: symbol_put_addr+0x54/0x60 RSP: ffff88006a7ce210
---[ end trace b75b357739e7e116 ]---

Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: imon: Fix null-ptr-deref in imon_probe

commit 58fd55e838276a0c13d1dc7c387f90f25063cbf3 upstream.

It seems that the return value of usb_ifnum_to_if() can be NULL and
needs to be checked.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dmaengine: dmatest: warn user when dma test times out

commit a9df21e34b422f79d9a9fa5c3eff8c2a53491be6 upstream.

Commit adfa543e7314 ("dmatest: don't use set_freezable_with_signal()")
introduced a bug (that is in fact documented by the patch commit text)
that leaves behind a dangling pointer. Since the done_wait structure is
allocated on the stack, future invocations to the DMATEST can produce
undesirable results (e.g., corrupted spinlocks). Ideally, this would be
cleaned up in the thread handler, but at the very least, the kernel
is left in a very precarious scenario that can lead to some long debug
sessions when the crash comes later.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=197605
Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

EDAC, sb_edac: Don't create a second memory controller if HA1 is not present

commit 15cc3ae001873845b5d842e212478a6570c7d938 upstream.

Yi Zhang reported the following failure on a 2-socket Haswell (E5-2603v3)
server (DELL PowerEdge 730xd):

  EDAC sbridge: Some needed devices are missing
  EDAC MC: Removed device 0 for sb_edac.c Haswell SrcID#0_Ha#0: DEV 0000:7f:12.0
  EDAC MC: Removed device 1 for sb_edac.c Haswell SrcID#1_Ha#0: DEV 0000:ff:12.0
  EDAC sbridge: Couldn't find mci handler
  EDAC sbridge: Couldn't find mci handler
  EDAC sbridge: Failed to register device with error -19.

The refactored sb_edac driver creates the IMC1 (the 2nd memory
controller) if any IMC1 device is present. In this case only
HA1_TA of IMC1 was present, but the driver expected to find
HA1/HA1_TM/HA1_TAD[0-3] devices too, leading to the above failure.

The document [1] says the 'E5-2603 v3' CPU has 4 memory channels max. Yi
Zhang inserted one DIMM per channel for each CPU, and did random error
address injection test with this patch:

      4024  addresses fell in TOLM hole area
     12715  addresses fell in CPU_SrcID#0_Ha#0_Chan#0_DIMM#0
     12774  addresses fell in CPU_SrcID#0_Ha#0_Chan#1_DIMM#0
     12798  addresses fell in CPU_SrcID#0_Ha#0_Chan#2_DIMM#0
     12913  addresses fell in CPU_SrcID#0_Ha#0_Chan#3_DIMM#0
     12674  addresses fell in CPU_SrcID#1_Ha#0_Chan#0_DIMM#0
     12686  addresses fell in CPU_SrcID#1_Ha#0_Chan#1_DIMM#0
     12882  addresses fell in CPU_SrcID#1_Ha#0_Chan#2_DIMM#0
     12934  addresses fell in CPU_SrcID#1_Ha#0_Chan#3_DIMM#0
    106400  addresses were injected totally.

The test result shows that all the 4 channels belong to IMC0 per CPU, so
the server really only has one IMC per CPU.

In the 1st page of chapter 2 in datasheet [2], it also says 'E5-2600 v3'
implements either one or two IMCs. For CPUs with one IMC, IMC1 is not
used and should be ignored.

Thus, do not create a second memory controller if the key HA1 is absent.

[1] http://ark.intel.com/products/83349/Intel-Xeon-Processor-E5-2603-v3-15M-Cache-1_60-GHz
[2] https://www.intel.com/content/dam/www/public/us/en/documents/datasheets/xeon-e5-v3-datasheet-vol-2.pdf

Reported-and-tested-by: Yi Zhang <yizhan@redhat.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170913104214.7325-1-qiuxu.zhuo@intel.com
[ Massage commit message. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.14

Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull x86 fixes from Thomas Gleixner:
 "A set of small fixes:

   - make KGDB work again which got broken by the conversion of WARN()
     to #UD. The WARN fixup needs to run before the notifier callchain,
     otherwise KGDB tries to handle it and crashes.

   - disable KASAN in the ORC unwinder to prevent false positive KASAN
     warnings

   - prevent default mapping above 47bit when 5 level page tables are
     enabled

   - make the delay calibration optimization work correctly, which had
     the conditionals the wrong way around and was operating on data
     which was not yet updated.

   - remove the bogus X86_TRAP_BP trap init from the default IDT init
     table, which broke 32bit int3 handling by overwriting the correct
     int3 setup.

   - replace this_cpu* with boot_cpu_data access in the preemptible
     oprofile init code"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/debug: Handle warnings before the notifier chain, to fix KGDB crash
  x86/mm: Fix ELF_ET_DYN_BASE for 5-level paging
  x86/idt: Remove X86_TRAP_BP initialization in idt_setup_traps()
  x86/oprofile/ppro: Do not use __this_cpu*() in preemptible context
  x86/unwind: Disable KASAN checking in the ORC unwinder
  x86/smpboot: Make optimization of delay calibration work correctly