GitHub/LineageOS/android_kernel_samsung_universal7580.git
15 years agopktgen: spin using hrtimer
Stephen Hemminger [Sat, 29 Aug 2009 06:41:29 +0000 (23:41 -0700)]
pktgen: spin using hrtimer

This changes how the pktgen thread spins/waits between
packets if delay is configured. It uses a high res timer to
wait for time to arrive.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agopktgen: convert to use ktime_t
Stephen Hemminger [Thu, 27 Aug 2009 13:55:16 +0000 (13:55 +0000)]
pktgen: convert to use ktime_t

The kernel ktime_t is a nice generic infrastructure for mananging
high resolution times, as is done in pktgen.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agopktgen: avoid calling gettimeofday
Stephen Hemminger [Thu, 27 Aug 2009 13:55:15 +0000 (13:55 +0000)]
pktgen: avoid calling gettimeofday

If not using delay then no need to update next_tx after
each packet sent. This allows pktgen to send faster especially
on systems with slower clock sources.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agopktgen: reorganize transmit loop
Stephen Hemminger [Thu, 27 Aug 2009 13:55:14 +0000 (13:55 +0000)]
pktgen: reorganize transmit loop

Handle standard (and non-standard) return values in a switch.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agopktgen: use netdev_alloc_skb
Stephen Hemminger [Thu, 27 Aug 2009 13:55:13 +0000 (13:55 +0000)]
pktgen: use netdev_alloc_skb

netdev_alloc_skb is NUMA node aware.
Also, don't exhaust atomic emergency pool. Don't want pktgen
to cause OOM behaviour.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agopktgen: cleanup clone count test
Stephen Hemminger [Thu, 27 Aug 2009 13:55:12 +0000 (13:55 +0000)]
pktgen: cleanup clone count test

The if statement to test for "should a new packet be used"
can be simplified.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agopktgen: xmit logic reorganization
Stephen Hemminger [Thu, 27 Aug 2009 13:55:11 +0000 (13:55 +0000)]
pktgen: xmit logic reorganization

Do some reorganization of transmit logic path:
   * move transmit queue full idle to separate routine
   * add a cpu_relax()
   * eliminate some of the uneeded goto's
   * if queue is still stopped, go back to main thread loop.
   * don't give up transmitting if quantum is exhausted (be greedy)

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agopktgen: stop_device cleanup
Stephen Hemminger [Thu, 27 Aug 2009 13:55:10 +0000 (13:55 +0000)]
pktgen: stop_device cleanup

All the callers were freeing skb after stopping device.
Remove unneeded forward decl.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agopktgen: mark read-only/mostly variables
Stephen Hemminger [Thu, 27 Aug 2009 13:55:09 +0000 (13:55 +0000)]
pktgen: mark read-only/mostly variables

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agopktgen: change inlining
Stephen Hemminger [Thu, 27 Aug 2009 13:55:08 +0000 (13:55 +0000)]
pktgen: change inlining

Don't force inlining where not needed. Gcc does better job
of deciding to inline local functions.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agopktgen: minor cleanup
Stephen Hemminger [Thu, 27 Aug 2009 13:55:07 +0000 (13:55 +0000)]
pktgen: minor cleanup

A couple of minor functions can be written more compactly.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agoqlge: Move TX completions from workqueue to NAPI.
Ron Mercer [Thu, 27 Aug 2009 11:02:11 +0000 (11:02 +0000)]
qlge: Move TX completions from workqueue to NAPI.

TX completions were running in a workqueue queued by the ISR.  This
patch moves the processing of TX completions to an existing RSS NAPI
context.
Now each irq vector runs NAPI for one RSS ring and one or more TX
completion rings.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agoqlge: Allow running MSIx with fewer vectors.
Ron Mercer [Thu, 27 Aug 2009 11:02:10 +0000 (11:02 +0000)]
qlge: Allow running MSIx with fewer vectors.

Currently we downshift to MSI/Legacy if we don't get enough vectors for
cpu_count RSS rings plus cpu_count TX completion rings.  This patch
allows running MSIX with the vector count that the platform provides.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agoqlge: Get rid of 'default' rx_ring type.
Ron Mercer [Thu, 27 Aug 2009 11:02:09 +0000 (11:02 +0000)]
qlge: Get rid of 'default' rx_ring type.

Currently we have three types of RX rings.

1) Default ring - services rx_ring for broadcast/multicast, handles
firmware events, and errors.

2) TX completion ring - handles only outbound completions.

3) RSS ring - handles only inbound completions.

This patch gets rid of the default ring type and moves it's functionality
into the first RSS ring.  This makes better use of MSIX vectors since
they are a limited resource on some platforms.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
David S. Miller [Sat, 29 Aug 2009 06:06:05 +0000 (23:06 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next-2.6

15 years agobonding: Have bond_check_dev_link examine netif_running
Petri Gynther [Fri, 28 Aug 2009 12:05:15 +0000 (12:05 +0000)]
bonding: Have bond_check_dev_link examine netif_running

bonding: Have bond_check_dev_link examine netif_running

Some network devices do not call netif_carrier_off when they
are set administratively down.  Have the bonding link check function
also inspect the netif_running state.  Ignore netif_running if the
bond_check_dev_link function is called with "reporting" set, as in that
case it's inspecting the capabilities of the non-netif_carrier device
driver.

Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agobonding: Fix useless test: int > INT_MAX
Nicolas de Pesloüan [Fri, 28 Aug 2009 13:18:34 +0000 (13:18 +0000)]
bonding: Fix useless test: int > INT_MAX

max_bonds is of type int and cannot be greater than INT_MAX.

Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agobonding: use compare_ether_addr
Stephen Hemminger [Fri, 28 Aug 2009 12:05:13 +0000 (12:05 +0000)]
bonding: use compare_ether_addr

Bonding can use compare_ether_addr() in bond_release.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agobonding: propogate vlan_features to bonding master
Jay Vosburgh [Fri, 28 Aug 2009 12:05:12 +0000 (12:05 +0000)]
bonding: propogate vlan_features to bonding master

Propogate the vlan_features of the slave devices to the bonding
master device, using the same logic as for regular features.

Tested by Or Gerlitz <ogerlitz@voltaire.com>, who also removed
the debug logic from the original test patch.

Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agolibertas: add NULL check on return value of get_zeroed_page
Kiran Divekar [Fri, 28 Aug 2009 12:17:59 +0000 (17:47 +0530)]
libertas: add NULL check on return value of get_zeroed_page

Most of the places in debugfs.c are missing a NULL check on the return value of
get_zeroed_page API call. Added required NULL check at appropriate places.

Signed-off-by: Kiran Divekar <kirandivekar@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agorndis_wlan: use cfg80211_wext_handler
Jussi Kivilinna [Fri, 28 Aug 2009 10:28:35 +0000 (13:28 +0300)]
rndis_wlan: use cfg80211_wext_handler

Now that cfg80211 functions are added and wext converted to use wext-compat
functions, remove wext structures and disabled code.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agorndis_wlan: disable IWEVPMKIDCAND wireless event
Jussi Kivilinna [Fri, 28 Aug 2009 10:28:30 +0000 (13:28 +0300)]
rndis_wlan: disable IWEVPMKIDCAND wireless event

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agorndis_wlan: convert mic failure wireless event to cfg80211
Jussi Kivilinna [Fri, 28 Aug 2009 10:28:24 +0000 (13:28 +0300)]
rndis_wlan: convert mic failure wireless event to cfg80211

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agorndis_wlan: remove unneeded SIOCSIWCOMMIT
Jussi Kivilinna [Fri, 28 Aug 2009 10:28:19 +0000 (13:28 +0300)]
rndis_wlan: remove unneeded SIOCSIWCOMMIT

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agorndis_wlan: rename wireless stats worker to device poller
Jussi Kivilinna [Fri, 28 Aug 2009 10:28:14 +0000 (13:28 +0300)]
rndis_wlan: rename wireless stats worker to device poller

Stats worker no longer poll stats from device anymore. It's still
needed to poll device control channel for connect/disconnect events,
so rename stats worker as device poller.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agorndis_wlan: add cfg80211 dump_station
Jussi Kivilinna [Fri, 28 Aug 2009 10:28:09 +0000 (13:28 +0300)]
rndis_wlan: add cfg80211 dump_station

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agorndis_wlan: add cfg80211 get_station
Jussi Kivilinna [Fri, 28 Aug 2009 10:28:03 +0000 (13:28 +0300)]
rndis_wlan: add cfg80211 get_station

Add cfg80211 get_station and convert SIOCGIWRATE and get_wireless_stats
to cfg80211.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agorndis_wlan: add cfg80211 key handling
Jussi Kivilinna [Fri, 28 Aug 2009 10:27:58 +0000 (13:27 +0300)]
rndis_wlan: add cfg80211 key handling

Add cfg80211 add_key/del_key/set_default_key and convert wext to use theim.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agorndis_wlan: add cfg80211 set_channel
Jussi Kivilinna [Fri, 28 Aug 2009 10:27:53 +0000 (13:27 +0300)]
rndis_wlan: add cfg80211 set_channel

Add cfg80211 set_channel and convert wext to use it.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agorndis_wlan: add cfg80211 connect, disconnect, join_ibss and leave_ibss
Jussi Kivilinna [Fri, 28 Aug 2009 10:27:47 +0000 (13:27 +0300)]
rndis_wlan: add cfg80211 connect, disconnect, join_ibss and leave_ibss

Add cfg80211 connect functions for station and ad-hoc modes and
convert wext to use theim.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agorndis_wlan: enable infrastructure before setting random essid
Jussi Kivilinna [Fri, 28 Aug 2009 09:59:26 +0000 (12:59 +0300)]
rndis_wlan: enable infrastructure before setting random essid

Random essid must be set to turn on radio when not connected. If device is
in ad-hoc mode, this results 'media connect' indications with the random
essid which should be ignored.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agorndis_wlan: set ieee80211_ptr->iftype in rndis_change_virtual_intf
Jussi Kivilinna [Fri, 28 Aug 2009 09:59:21 +0000 (12:59 +0300)]
rndis_wlan: set ieee80211_ptr->iftype in rndis_change_virtual_intf

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agorndis_wlan: use is_zero_ether_addr() and is_broadcast_ether_addr()
Jussi Kivilinna [Fri, 28 Aug 2009 09:59:15 +0000 (12:59 +0300)]
rndis_wlan: use is_zero_ether_addr() and is_broadcast_ether_addr()

Use is_zero_ether_addr() and is_broadcast_ether_addr() instead of
memcmp against ffff_bssid/zero_bssid.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agorndis_wlan: move link up/down work to separate functions
Jussi Kivilinna [Fri, 28 Aug 2009 09:59:10 +0000 (12:59 +0300)]
rndis_wlan: move link up/down work to separate functions

Move link up/down work to separate functions and use local array
for allocating memory for info structure instead of kzmalloc.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agorndis_wlan: increase scan timer delay
Jussi Kivilinna [Fri, 28 Aug 2009 09:59:05 +0000 (12:59 +0300)]
rndis_wlan: increase scan timer delay

Increase scan delay from 1 sec to 6 sec. Spec says that scan by
OID_802_11_BSSID_LIST_SCAN completes in 6 seconds.
Before rfkill patch too short delay was not problem as device was
always active (radio on) and performing background scanning.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agorndis_wlan: resize bssid list if too small
Jussi Kivilinna [Fri, 28 Aug 2009 09:59:00 +0000 (12:59 +0300)]
rndis_wlan: resize bssid list if too small

Buffer used for bssid list might be too small. Change rndis_query_oid()
to return required buffer length to caller and make rndis_check_bssid_list()
resize buffer when needed.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agorndis_wlan: get bssid scan list before new scan
Jussi Kivilinna [Fri, 28 Aug 2009 09:58:55 +0000 (12:58 +0300)]
rndis_wlan: get bssid scan list before new scan

OID_802_11_BSSID_LIST_SCAN clears device's bssid list, so retrieve
current bssid list from device before issuing new scan.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agorndis_wlan: ignore OID_802_11_ADD_KEY triggered media connect indications
Jussi Kivilinna [Fri, 28 Aug 2009 09:58:49 +0000 (12:58 +0300)]
rndis_wlan: ignore OID_802_11_ADD_KEY triggered media connect indications

Setting WPA keys with OID_802_11_ADD_KEY sometimes trigger
instant media connect indication. These indications are extranous and
should be ignored, as otherwise driver would send reassociation event to
userspace which in this case is not needed.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agob43: Implement antenna diversity support for LP-PHY
Gábor Stefanik [Thu, 27 Aug 2009 20:49:49 +0000 (22:49 +0200)]
b43: Implement antenna diversity support for LP-PHY

The A/G-PHY changes are fallout fixes from the enum change,
which in turn allows the LP-PHY code to be much simpler.
The antenna_to_phyctl change is a fix for a potential
existing bug that this patch may otherwise trigger.

Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agob43: Enable LP-PHY support by default and remove Kconfig warning
Gábor Stefanik [Thu, 27 Aug 2009 15:24:23 +0000 (17:24 +0200)]
b43: Enable LP-PHY support by default and remove Kconfig warning

The most common LP-PHY device, BCM4312, is now fully functional.
So, no need to say "probably won't work for you" anymore.
It's also not "for debuggers and developers only", as it is
perfectly usable for end-users now (at least for BCM4312).

Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoath5k: don't use PCI ID to find the chip revision
Pavel Roskin [Thu, 27 Aug 2009 02:30:09 +0000 (22:30 -0400)]
ath5k: don't use PCI ID to find the chip revision

AR5K_SREV is available even if the chip has been put to sleep.  Relying
on the chip register allows binding non-standard PCI IDs by

echo VENDOR_ID PRODUCT_ID >/sys/bus/pci/drivers/ath5k/new_id

without having to specify the driver data as well.

Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoath5k: fix uninitialized value use in ath5k_eeprom_read_turbo_modes()
Pavel Roskin [Thu, 27 Aug 2009 02:30:00 +0000 (22:30 -0400)]
ath5k: fix uninitialized value use in ath5k_eeprom_read_turbo_modes()

The `val' variable in ath5k_eeprom_read_turbo_modes() is used
uninitialized.  gcc 4.4.1 with -fno-inline-functions-called-once reports
it:

eeprom.c: In function 'ath5k_eeprom_read_turbo_modes':
eeprom.c:441: warning: 'val' may be used uninitialized in this function

Comparing the code to the Atheros HAL, it's clear that the split between
ath5k_eeprom_read_modes() and ath5k_eeprom_read_turbo_modes() was
incorrect.

The Atheros HAL reads both turbo and non-turbo data from EEPROM in one
function.  Some turbo mode parameters are derived from the same EEPROM
values as non-turbo parameters, just from different bits.

Merge ath5k_eeprom_read_turbo_modes() into ath5k_eeprom_read_modes() to
fix the warning.  The actual values and offsets have been cross-checked
against Atheros HAL.

Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoath5k: clarify srev comparison for CCMP check
Bob Copeland [Thu, 27 Aug 2009 19:17:15 +0000 (15:17 -0400)]
ath5k: clarify srev comparison for CCMP check

As Pavel Roskin noted, the check for mac version as copied from
legacy_hal made no sense.  This replaces it with the equivalent
and makes up a suitable #define for the mac version legacy_hal
checked.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agob43: LP-PHY: Revert to the original PHY register write routine
Gábor Stefanik [Wed, 26 Aug 2009 21:46:18 +0000 (23:46 +0200)]
b43: LP-PHY: Revert to the original PHY register write routine

After some discussion on IRC about the PHY register write change,
I am not sure anymore if this is the right thing to do.

Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoiwlwifi: fix ICT irq table endianness
Johannes Berg [Wed, 26 Aug 2009 20:15:13 +0000 (22:15 +0200)]
iwlwifi: fix ICT irq table endianness

The ICT IRQ table is a set of __le32 values, not u32 values,
so when reading it we need to take into account that it has
to be converted to CPU endianness. This was causing a lot of
trouble on my powerpc box where various things would simply
not work for no apparent reason with 5xxx cards, but worked
with 4965 -- which doesn't use the ICT table.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agort2x00: Cleanup rt2x00mac_bss_info_changed()
Ivo van Doorn [Wed, 26 Aug 2009 19:04:08 +0000 (21:04 +0200)]
rt2x00: Cleanup rt2x00mac_bss_info_changed()

Since patch "rt2x00: bss_info_changed() callback is allowed to sleep" the
variable delayed wasn't used anymore. This means it can be removed
along with the call to schedule_work which depended on that variable.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agossb: Implement PMU LDO control and use it in b43
Gábor Stefanik [Wed, 26 Aug 2009 18:51:26 +0000 (20:51 +0200)]
ssb: Implement PMU LDO control and use it in b43

Implement the "PMU LDO set voltage" and "PMU LDO PA ref enable"
functions, and use them during LP-PHY baseband init in b43.

Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agob43: Fix and update LP-PHY code
Gábor Stefanik [Wed, 26 Aug 2009 18:51:25 +0000 (20:51 +0200)]
b43: Fix and update LP-PHY code

-Fix a few nasty typos (b43_phy_* operations instead of b43_radio_*)
 in the channel tune routines.
-Fix some typos & spec errors found by MMIO tracing.
-Optimize b43_phy_write & b43_phy_mask/set/maskset to use
 only the minimal number of MMIO accesses. (Write is possible
 using a single 32-bit MMIO write, while set/mask/maskset can
 be done in 3 16-bit MMIOs).
-Set the default channel back to 1, as the bug forcing us to use
 channel 7 is now fixed.

With this, the device comes up, scans, associates, transmits,
receives, monitors and injects on all channels - in other words,
it's fully functional. Sensitivity and TX power are still sub-optimal,
due to the lack of calibration (that's next on my list).

Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agob43: LP-PHY: Fix and simplify Qdiv roundup
Gábor Stefanik [Wed, 26 Aug 2009 18:51:24 +0000 (20:51 +0200)]
b43: LP-PHY: Fix and simplify Qdiv roundup

The Qdiv roundup routine is essentially a fixed-point
division algorithm, using only integer math.
However, the version in the specs had a major error
that has been recently fixed (a missing quotient++).

Replace Qdiv roundup with a rewritten, simplified version.

Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agortl8187: Implement rfkill support
Herton Ronaldo Krzesinski [Wed, 26 Aug 2009 16:54:09 +0000 (13:54 -0300)]
rtl8187: Implement rfkill support

This change implements rfkill support for RTL8187B and RTL8187L devices,
using new cfg80211 rfkill API.

Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agortl8187: fix circular locking (rtl8187_stop/rtl8187_work)
Herton Ronaldo Krzesinski [Wed, 26 Aug 2009 16:54:08 +0000 (13:54 -0300)]
rtl8187: fix circular locking (rtl8187_stop/rtl8187_work)

Larry Finger reports following lockdep warning:

[ INFO: possible circular locking dependency detected ]
2.6.31-rc6-wl #201
-------------------------------------------------------
rfkill/30578 is trying to acquire lock:
 (&(&priv->work)->work#2){+.+...}, at: [<ffffffff81051215>]
__cancel_work_timer+0xd9/0x222

but task is already holding lock:
 (&priv->conf_mutex#2){+.+.+.}, at: [<ffffffffa064a024>]
rtl8187_stop+0x31/0x364 [rtl8187]

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #1 (&priv->conf_mutex#2){+.+.+.}:
       [<ffffffff81065957>] __lock_acquire+0x12d0/0x1614
       [<ffffffff81065d54>] lock_acquire+0xb9/0xdd
       [<ffffffff8127c32f>] mutex_lock_nested+0x56/0x2a8
       [<ffffffffa064a392>] rtl8187_work+0x3b/0xf2 [rtl8187]
       [<ffffffff81050758>] worker_thread+0x1fa/0x30a
       [<ffffffff81054ca5>] kthread+0x8f/0x97
       [<ffffffff8100cb7a>] child_rip+0xa/0x20
       [<ffffffffffffffff>] 0xffffffffffffffff

-> #0 (&(&priv->work)->work#2){+.+...}:
       [<ffffffff8106568c>] __lock_acquire+0x1005/0x1614
       [<ffffffff81065d54>] lock_acquire+0xb9/0xdd
       [<ffffffff8105124e>] __cancel_work_timer+0x112/0x222
       [<ffffffff8105136b>] cancel_delayed_work_sync+0xd/0xf
       [<ffffffffa064a33f>] rtl8187_stop+0x34c/0x364 [rtl8187]
       [<ffffffffa0242866>] ieee80211_stop_device+0x29/0x61 [mac80211]
       [<ffffffffa0239194>] ieee80211_stop+0x476/0x530 [mac80211]
       [<ffffffff8120ce15>] dev_close+0x8a/0xac
       [<ffffffffa01d9fa7>] cfg80211_rfkill_set_block+0x4a/0x7a [cfg80211]
       [<ffffffffa01bf4f0>] rfkill_set_block+0x84/0xd9 [rfkill]
       [<ffffffffa01bfc31>] rfkill_fop_write+0xda/0x124 [rfkill]
       [<ffffffff810cf286>] vfs_write+0xae/0x14a
       [<ffffffff810cf3e6>] sys_write+0x47/0x6e
       [<ffffffff8100ba6b>] system_call_fastpath+0x16/0x1b
       [<ffffffffffffffff>] 0xffffffffffffffff

The problem here is that rtl8187_stop, while helding priv->conf_mutex,
runs cancel_delayed_work_sync on an workqueue that runs rtl8187_work,
which also takes priv->conf_mutex lock. Move cancel_delayed_work_sync
out of rtl8187_stop priv->conf_mutex locking region.

Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoath9k: Add Bluetooth Coexistence 3-wire support
Vasanthakumar Thiagarajan [Wed, 26 Aug 2009 15:38:50 +0000 (21:08 +0530)]
ath9k: Add Bluetooth Coexistence 3-wire support

This patch adds 3-wire bluetooth coex support for AR9285.
This support can be enabled through btcoex_enable modparam.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoath9k: Add infrastructure for generic hw timers
Vasanthakumar Thiagarajan [Wed, 26 Aug 2009 15:38:49 +0000 (21:08 +0530)]
ath9k: Add infrastructure for generic hw timers

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoath9k: Remove hw capability bit meant for btcoex
Vasanthakumar Thiagarajan [Wed, 26 Aug 2009 15:38:48 +0000 (21:08 +0530)]
ath9k: Remove hw capability bit meant for btcoex

We don't need a hw cap bit for btcoex anymore as btcoex scheme type
is enough to do this.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoath9k: Determine btcoex scheme type based on chip version
Vasanthakumar Thiagarajan [Wed, 26 Aug 2009 15:38:47 +0000 (21:08 +0530)]
ath9k: Determine btcoex scheme type based on chip version

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoath9k: Move btcoex related data to a separate struct
Vasanthakumar Thiagarajan [Wed, 26 Aug 2009 15:38:46 +0000 (21:08 +0530)]
ath9k: Move btcoex related data to a separate struct

Also define macros for wlanactive and btactive (5 & 6) gpios.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoath9k: Configure btcoex register during every reset
Vasanthakumar Thiagarajan [Wed, 26 Aug 2009 15:38:45 +0000 (21:08 +0530)]
ath9k: Configure btcoex register during every reset

Make sure btcoex register configured with appropriate values
after it is initialized with the default values from initvals.h
during reset.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoath9k: Move btcoex stuff from hw.[ch] to new btcoex.[ch]
Vasanthakumar Thiagarajan [Wed, 26 Aug 2009 15:38:44 +0000 (21:08 +0530)]
ath9k: Move btcoex stuff from hw.[ch] to new btcoex.[ch]

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoath9k: Split ath9k_hw_btcoex_enable() into two logical pieces
Vasanthakumar Thiagarajan [Wed, 26 Aug 2009 15:38:43 +0000 (21:08 +0530)]
ath9k: Split ath9k_hw_btcoex_enable() into two logical pieces

This function currently does initialization + enable the
btcoex support. Split it into two logical functions which
does the above operations separately. Btcoex initialization
is done during attach time and enabling this feature is done
in start(). Also, add code to disable btcoex support in stop().

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agorndis_wlan: set cipher suites for cfg80211
Jussi Kivilinna [Wed, 26 Aug 2009 12:53:02 +0000 (15:53 +0300)]
rndis_wlan: set cipher suites for cfg80211

rndis_wlan does not set cipher suites list for cfg80211 which causes
wext-compat-range to report rndis_wlan not supporting WPA. Patch adds
cipher suites list and fixes NetworkManager not being able to connect to
WPA encrypted APs.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoath9k: Wrap DMA dump function with PS wakeup/restore
Sujith [Wed, 26 Aug 2009 05:41:57 +0000 (11:11 +0530)]
ath9k: Wrap DMA dump function with PS wakeup/restore

When dumping register contents, HW has to be awake.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoath9k: Update INITVALs for AR9285
Sujith [Wed, 26 Aug 2009 03:09:55 +0000 (08:39 +0530)]
ath9k: Update INITVALs for AR9285

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoath9k: Handle PA cal usage properly
Sujith [Wed, 26 Aug 2009 03:09:52 +0000 (08:39 +0530)]
ath9k: Handle PA cal usage properly

PA Calibration is not needed for high power solutions.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoath9k: Fix bugs in programming registers during PA CAL
Sujith [Wed, 26 Aug 2009 03:09:50 +0000 (08:39 +0530)]
ath9k: Fix bugs in programming registers during PA CAL

* First PA driver (PDPADRV1) was not powered down properly.
* Compensation capacitor for dynamic PA was programmed incorrectly.

Also, remove a stray REG_READ.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoath9k: Reduce the frequency of PA offset calibration
Sujith [Wed, 26 Aug 2009 03:09:40 +0000 (08:39 +0530)]
ath9k: Reduce the frequency of PA offset calibration

PA calibration need not be done if the offset is not varying.
The current logic does PA calibration even if the offset is the
same.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agolibipw: initiate cfg80211 API conversion
John W. Linville [Tue, 25 Aug 2009 18:12:25 +0000 (14:12 -0400)]
libipw: initiate cfg80211 API conversion

Initiate the conversion of libipw to the new cfg80211 configuration API.

For now, leave CONFIG_IPW2200_PROMISCUOUS stuff alone.  Eventually
migrate it to cfg80211 when the add/del/change_virtual_intf methods
are implemented.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoath9k: Fix read buffer overflow
Roel Kluin [Fri, 7 Aug 2009 21:50:00 +0000 (23:50 +0200)]
ath9k: Fix read buffer overflow

Prevent a read of powInfo[-1] in the first iteration.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agomac80211: Check pending scan request after having processed mgd work
Jouni Malinen [Tue, 25 Aug 2009 14:44:28 +0000 (17:44 +0300)]
mac80211: Check pending scan request after having processed mgd work

When the queued management work items are processed in
ieee80211_sta_work() an item could be removed. This could change the
anybusy from true to false, so we better check whether we can start a
new scan only after having processed the pending work first.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agomac80211: fix scan cancel on ifdown
Johannes Berg [Tue, 25 Aug 2009 14:33:47 +0000 (16:33 +0200)]
mac80211: fix scan cancel on ifdown

When an interface is taken down while a scan is
pending -- i.e. a scan request was accepted but
not yet acted upon due to other work being in
progress -- we currently do not properly cancel
that scan and end up getting stuck. Fix this by
doing better checks when an interface is taken
down.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agob43: LP-PHY: Fix a few typos in the RC calibration code
Gábor Stefanik [Tue, 25 Aug 2009 14:17:48 +0000 (16:17 +0200)]
b43: LP-PHY: Fix a few typos in the RC calibration code

The RC calibration code has some typos - fix them.
Also, make the default channel 7, as channel 1 is still
broken (only channels 7 and 8, and occasionally 9 work).

Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoPRISM54: fix compilation warning
Jaswinder Singh Rajput [Tue, 25 Aug 2009 09:58:45 +0000 (15:28 +0530)]
PRISM54: fix compilation warning

CC [M]  drivers/net/wireless/prism54/islpci_eth.o
drivers/net/wireless/prism54/islpci_eth.c: In function ‘islpci_eth_cleanup_transmit’:
drivers/net/wireless/prism54/islpci_eth.c:53: warning: cast from pointer to integer of different size
drivers/net/wireless/prism54/islpci_eth.c: In function ‘islpci_eth_receive’:
drivers/net/wireless/prism54/islpci_eth.c:453: warning: cast from pointer to integer of different size

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoath5k: add hardware CCMP encyption support
Bob Copeland [Tue, 25 Aug 2009 03:00:33 +0000 (23:00 -0400)]
ath5k: add hardware CCMP encyption support

Recent ath5k hardware is capable of doing CCMP acceleration.
Enable it for the cards that support it.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoath5k: use the skb->cb directly for RX status
Bob Copeland [Tue, 25 Aug 2009 03:00:32 +0000 (23:00 -0400)]
ath5k: use the skb->cb directly for RX status

Save a memcpy by just storing updates directly in the skb
control block.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoath5k: add led pin configuration for compaq c700 laptop
Marcos Chaparro [Tue, 25 Aug 2009 03:00:31 +0000 (23:00 -0400)]
ath5k: add led pin configuration for compaq c700 laptop

With this patch, a compaq c700 can turn on the wifi led.
The array of compatible devices now includes the hardware
present in this computer, as well as the led pin and
polarity.

Signed-off-by: Marcos Chaparro <nitrousnrg@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoath5k: clean up filter flags setting
Bob Copeland [Tue, 25 Aug 2009 03:00:30 +0000 (23:00 -0400)]
ath5k: clean up filter flags setting

The maze of if() statements in configure_filter is confusing.
Reorganizing it as a switch statement makes it more apparent what
is going on and reveals several suspicious settings.  This has no
functional changes, though it does remove some redundant flags
that are set earlier.

Also now that we can sleep, protect sc->filter_flags with the
sc lock.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agomac80211: Fix output of minstrels rc_stats
Arnd Hannemann [Mon, 24 Aug 2009 18:51:46 +0000 (20:51 +0200)]
mac80211: Fix output of minstrels rc_stats

An integer overflow in the minstrel debug code prevented the
throughput to be displayed correctly. This patch fixes that,
by permutating operations like proposed by Pavel Roskin.

Signed-off-by: Arnd Hannemann <hannemann@nets.rwth-aachen.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agomwl8k: separate driver and device info reporting during probe
Lennert Buytenhek [Mon, 24 Aug 2009 13:48:07 +0000 (15:48 +0200)]
mwl8k: separate driver and device info reporting during probe

Only print the driver version once, and condense all per-PHY
information to a single line.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agomwl8k: missing endian conversion when printing firmware command result
Lennert Buytenhek [Mon, 24 Aug 2009 13:42:56 +0000 (15:42 +0200)]
mwl8k: missing endian conversion when printing firmware command result

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agomwl8k: fix pci dma mapping leak in mwl8k_post_cmd() error path
Lennert Buytenhek [Mon, 24 Aug 2009 13:42:46 +0000 (15:42 +0200)]
mwl8k: fix pci dma mapping leak in mwl8k_post_cmd() error path

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agomwl8k: fix inverted error test in mwl8k_bss_info_changed()
Lennert Buytenhek [Mon, 24 Aug 2009 13:42:36 +0000 (15:42 +0200)]
mwl8k: fix inverted error test in mwl8k_bss_info_changed()

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agomac80211: fix RX skb leaks
Johannes Berg [Mon, 24 Aug 2009 09:46:30 +0000 (11:46 +0200)]
mac80211: fix RX skb leaks

In mac80211's RX path some of the warnings that
warn about drivers passing invalid status values
leak the skb, fix that by refactoring the code.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agonl80211: jump to out_err upon unsupported iftype
Roel Kluin [Sat, 22 Aug 2009 19:15:49 +0000 (21:15 +0200)]
nl80211: jump to out_err upon unsupported iftype

Jump to out_err when the iftype is not supported.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoar9170: remove unnecessary call to ar9170_set_beacon_timers
Joerg Albert [Fri, 21 Aug 2009 20:53:37 +0000 (22:53 +0200)]
ar9170: remove unnecessary call to ar9170_set_beacon_timers

Signed-off-by: Joerg Albert <jal2@gmx.de>
Acked-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoar9170: cleanup of bss_info_changed and beacon config
Joerg Albert [Fri, 21 Aug 2009 21:25:07 +0000 (23:25 +0200)]
ar9170: cleanup of bss_info_changed and beacon config

Add beacon control by BSS_CHANGED_BEACON_ENABLED and
bss_conf->enable_beacon from mac80211.

Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoMAINTAINERS: Update ipw2x00 and iwlwifi entries
Reinette Chatre [Fri, 21 Aug 2009 21:03:51 +0000 (14:03 -0700)]
MAINTAINERS: Update ipw2x00 and iwlwifi entries

Update MAINTAINERS file to reflect current maintenance status of ipw2x00
drivers. We remove James's name as he is not involved with this project
anymore. We also update the Status to "Odd Fixes". This has been true for a
while now, we have to make it official. There is also a new email address
with which all relevant people can be reached. The same email address
should be used for iwlwifi.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: James Ketrenos <jketreno@linux.intel.com>
Acked-by: James Ketrenos <jketreno@linux.intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoipw2x00: update contact information
Reinette Chatre [Fri, 21 Aug 2009 20:34:26 +0000 (13:34 -0700)]
ipw2x00: update contact information

Intel Linux wireless folks can be reached via this address.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoiwlwifi: fix unloading driver while scanning
Wey-Yi Guy [Fri, 21 Aug 2009 20:34:25 +0000 (13:34 -0700)]
iwlwifi: fix unloading driver while scanning

If NetworkManager is busy scanning when user
tries to unload the module, the driver can not be unloaded
because HW still scanning.

Make sure driver sends abort scan host command to uCode if it
is in the middle of scanning during driver unload.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoiwlwifi: fix remove key error
Abhijeet Kolekar [Fri, 21 Aug 2009 20:34:24 +0000 (13:34 -0700)]
iwlwifi: fix remove key error

Fix following error by sending synchronous command and waiting for the command
to complete.

mac80211-phy0: failed to remove key (0, ff:ff:ff:ff:ff:ff) from hardware (-16).

-16 is EBUSY error. The asynchronous command tests for STATUS_EXIT_PENDING
while interface is getting down and it returns -EBUSY error if set.
Changing the host command from asynchronous call to synchronous call
enables command to be run while interface is going down.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoiwlwifi: read enhanced tx power info from EEPROM image
Wey-Yi Guy [Fri, 21 Aug 2009 20:34:23 +0000 (13:34 -0700)]
iwlwifi: read enhanced tx power info from EEPROM image

For 6000 series and up, additional enhanced regulatory tx power
limitation information is added to EEPROM image.

In order to setup the tx power limitation per channel correctly. Read
the enhanced tx power information from EEPROM image and update
accordingly.

The information is provided per SISO (a,b,c) chain based, it also has
information for both MIMO2 and MIMO3. For tx power regulatory
limitation, take the highest number from all the chains and update.
Also update tx_power_user_lmt to the highest power supported by any
channels and chains

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoiwlwifi: remove duplicated define
Wey-Yi Guy [Fri, 21 Aug 2009 20:34:22 +0000 (13:34 -0700)]
iwlwifi: remove duplicated define

Remove duplicated define "STA_FLG_PWR_SAVE_MSK"

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoiwlwifi: set HT flags in ieee80211_rx_status for received packets
Daniel C Halperin [Fri, 21 Aug 2009 20:34:21 +0000 (13:34 -0700)]
iwlwifi: set HT flags in ieee80211_rx_status for received packets

Add code to set the HT flags (HT, 40 MHz, Short guard interval) in
the ieee80211_rx_status field passed to mac80211.  This ensures that mac80211
processes these HT packets correctly.

Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoiwlwifi: clear rate control flags on non-HT packet
Daniel C Halperin [Fri, 21 Aug 2009 20:34:20 +0000 (13:34 -0700)]
iwlwifi: clear rate control flags on non-HT packet

Clear the flags (most importantly, the IEEE80211_TX_RC_MCS flag)
when sending a non-HT packet so that the rate index can be properly treated.
This fixes the reporting of legacy rates in wireless-extensions for packets
sent after an HT packet.

Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoiwlwifi: show current tx power
Wey-Yi Guy [Fri, 21 Aug 2009 20:34:19 +0000 (13:34 -0700)]
iwlwifi: show current tx power

debugFs file show current tx power for all the transmit chains

Adding "tx_power" file in /sys/kernal/debug/ieee80211/phy0/iwlagn/debug
to display current tx power for all the active chains in 1/2 dB step.

Show tx power information "Not available" if uCode can not provide the
information or interface is down.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoiwlwifi: change IWL6000_UCODE_API_MAX to v4
Wey-Yi Guy [Fri, 21 Aug 2009 20:34:18 +0000 (13:34 -0700)]
iwlwifi: change IWL6000_UCODE_API_MAX to v4

uCode version changed to v4 for 6000 series

The additional parameter added to v4 is providing current tx power for
each chain in tx statistics portion of "statistics notification"
command.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoiwlwifi: error checking for setting tx_power in sysfs
Wey-Yi Guy [Fri, 21 Aug 2009 20:34:17 +0000 (13:34 -0700)]
iwlwifi: error checking for setting tx_power in sysfs

Perform error checking and report failure when setting tx power from
sysfs.
If fail to set the tx power, do not update the local copy, so user will
not see the incorrect tx power in sysfs

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoiwlwifi: name changes from "tx_power_channel_lmt" to "tx_power_device_lmt"
Wey-Yi Guy [Fri, 21 Aug 2009 20:34:16 +0000 (13:34 -0700)]
iwlwifi: name changes from "tx_power_channel_lmt" to "tx_power_device_lmt"

Changing the name from "tx_power_channel_lmt" to "tx_power_device_lmt";
to give idea that scope of limit is for overall device, not any
individual channels

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoiwlwifi: do not allow set tx power over channel power limit
Wey-Yi Guy [Fri, 21 Aug 2009 20:34:15 +0000 (13:34 -0700)]
iwlwifi: do not allow set tx power over channel power limit

When setting tx power in sysfs, check against max channel tx power
limit instead of IWL_TX_POWER_TARGET_POWER_MAX.

Different devices have different max tx power limit; using
IWL_TX_POWER_TARGET_POWER_MAX can excess the limitaion and give wrong
information.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoiwlwifi: set default tx power user limit to minimal
Wey-Yi Guy [Fri, 21 Aug 2009 20:34:14 +0000 (13:34 -0700)]
iwlwifi: set default tx power user limit to minimal

Set the tx_power_user_lmt to the lowest power level
this value will get overwritten by channel's max power avg
from eeprom

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agoiwlwifi: Make injection of non-broadcast frames work again
Gábor Stefanik [Fri, 21 Aug 2009 18:44:09 +0000 (20:44 +0200)]
iwlwifi: Make injection of non-broadcast frames work again

Commit 1ccb84d87d04df3c76cd4352fe69786d8c7cf016 by Wey-Yi Guy
("iwlwifi: clean up unused NL80211_IFTYPE_MONITOR for Monitor mode")
broke injection of non-broadcast frames to unassociated stations
(causing a SYSASSERT for all such injected frames), due to injected
frames no longer automatically getting a broadcast station ID assigned.
This patch restores the old behavior, fixing the aforementioned
regression.

Also, consistently check for IEEE80211_TX_CTL_INJECTED instead of
iwl_is_monitor_mode in the TX path, as TX_CTL_INJECTED specifically
means that a given packet is coming from a monitor interface, while
iwl_is_monitor_mode only shows whether a monitor interface exists
on the device.

Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
15 years agolibertas: Add support for Marvell Libertas CF8305
Marek Vasut [Fri, 21 Aug 2009 02:08:16 +0000 (04:08 +0200)]
libertas: Add support for Marvell Libertas CF8305

The CF8305 is a very old silicon running firmware version 3.0 . This card also
needs some special treatment as it's so old it can't do unaligned register
access. But since that happens only at one place, there were no changes made to
the register access functions, but instead that particular place was fixed.
Also, this card uses only one-stage firmware which is loaded the same way as
helper firmware. The second-stage firmware isn't loaded on this card and doesn't
therefore have to be supplied.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>