forcedeth: mac address mcp77/79

This patch is a critical fix for MCP77 and MCP79 devices. The feature
flags were missing the define for correct mac address
(DEV_HAS_CORRECT_MACADDR).

Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

forcedeth: multicast fix

This patch fixes the case where no multicast addresses are requested to
be added to the multicast filter. The multicast mask must be set to all
1's instead of all 0's.

Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

forcedeth: tx pause fix

This patch fixes the tx pause enable watermark flags. The new values
where determined to be optimal during testing.

Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

forcedeth: updated copyright section

This patch updates the copyright section to include 2007 and 2008.

Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

forcedeth: checksum fix

The driver should inform the stack when checksum has been performed by
the HW when both IP and TCP (or UDP) checksum flags are indicated by HW.

Previously, it would also inform the stack when only IP checksum flag
was indicated by HW. This can cause data corruption when IP fragments
are used. The IP Identification field can wrap around and cause data
from new fragments to fill into older fragment slots with same IP Id.
The stack would then not perform TCP/UDP checksum (after re-assembly of
all fragments) since driver falsely stated it was already calculated.

Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

forcedeth: reset register fix

This patch fixes the reset register definition from 0x3C to 0x34.

Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/arm/at91_ether.c: logical/bitand typo in function reset_phy()

include/linux/mii.h:48:#define BMCR_RESET 0x8000

The function reset_phy() is in "#if 0" inactivated code

Replace logical "&&" by bit "&" before BMCR_RESET

Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb3: Remove incorrect __devinit annotations

When PCI error recovery was added to cxgb3, a function t3_io_slot_reset()
was added.  This function can call back into t3_prep_adapter() at any
time, so t3_prep_adapter() can no longer be marked __devinit.
This patch removes the __devinit annotation from t3_prep_adapter() and
all the functions that it calls, which fixes

    WARNING: drivers/net/cxgb3/built-in.o(.text+0x2427): Section mismatch in reference from the function t3_io_slot_reset() to the function .devinit.text:t3_prep_adapter()

Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: update MAINTAINERS

Remove Chad Tindel; he hasn't been involved for a number
of years.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: update version

Update bonding to version 3.2.4.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: do not acquire rtnl in ARP monitor

The ARP monitor functions currently acquire RTNL when performing
failover operations, but do so incorrectly (out of order).  This causes
various warnings from might_sleep.

The ARP monitor isn't supported for any of the bonding modes
that actually require RTNL, so it is safe to not hold RTNL when
failing over in the ARP monitor.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: fix race that causes invalid statistics

I've seen reports of invalid stats in /proc/net/dev for bonding
interfaces, and found it's a pretty easy problem to reproduce.  Since
the current code zeros the bonding stats when a read is requested and a
pointer to that data is returned to the caller we cannot guarantee that
the caller has completely accessed the data before a successive call to
request the stats zeroes the stats again.

This patch creates a new stack variable to keep track of the updated
stats and copies the data from that variable into the bonding stats
structure.  This ensures that the value for any of the bonding stats
should not incorrectly return zero for any of the bonding statistics.
This does use more stack space and require an extra memcpy, but it seems
like a fair trade-off for consistently correct bonding statistics.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Chris Snook <csnook@redhat.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: fix NULL pointer deref in startup processing

Fix the "are we creating a duplicate" check to not compare
the name if the name is NULL (meaning that the system should select
a name).  Bug reported by Benny Amorsen <benny+usenet@amorsen.dk>.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: fix set_multicast_list locking

This patch eliminates a problem (reported by lockdep) in the
bond_set_multicast_list function.  It first reduces the locking on
bond->lock to a simple read_lock, and second, adds netif_tx locking
around the bonding mc_list manipulations that occur outside of the
set_multicast_list function.

The original problem was related to IPv6 addrconf activity.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: fix parameter parsing

My last fix (commit ece95f7fefe3afae19e641e1b3f5e64b00d5b948)
didn't handle one case correctly.  This resolves that, and it will now
correctly parse parameters with arbitrary white space, and either text
names or mode values.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix/Rewrite of the mipsnet driver]

This is Thiemo's patch.

----- Forwarded message from Thiemo Seufer <ths@networkno.de> -----

From: Thiemo Seufer <ths@networkno.de>
Date: Sat, 17 Nov 2007 22:29:13 +0000
To: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org, ralf@linux-mips.org
Subject: [PATCH, REPOST] Fix/Rewrite of the mipsnet driver
Content-Type: text/plain; charset=us-ascii

Hello All,

currently the mipsnet driver fails after transmitting a number of
packages because SKBs are allocated but never freed. I fixed that
and coudn't refrain from removing the most egregious warts.

- mipsnet.h folded into mipsnet.c, as it doesn't provide any
  useful external interface.
- Free SKB after transmission.
- Call free_irq in mipsnet_close, to balance the request_irq in
  mipsnet_open.
- Removed duplicate read of rxDataCount.
- Some identifiers are now less verbose.
- Removed dead and/or unnecessarily complex code.
- Code formatting fixes.

Tested on Qemu's mipssim emulation, with this patch it can boot a
Debian NFSroot.

Thiemo

Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

remove obsolete tokenring maintainer information

- Peter's email address is bouncing
- the project webpage no longer exists
- neither Peter nor Mike had a single patch included in the kernel
  since 2.6.12-rc2 (when the git history begins)

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: remove unneeded declaration shadowing earlier one

This removes a sparse warning.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: tweak irq allocation messages

There's too much noise on systems that don't support MSI.  Let's get rid
of a few and make the real error message more specific.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

e100: fix spelling errors

Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000: make e1000_dump_eeprom() static

This patch makes the needlessly global e1000_dump_eeprom() static.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: make a function static

This patch makes the needlessly global reg_pattern_test_array() static.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Net: e100, fix iomap mem accesses

Patch against netdev-2.6 follows.
--
writeX functions are not permitted on iomap-ped space change to iowriteX,
also pci_unmap pci_map-ped space on exit (instead of iounmap).

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

pasemi_mac: Disable interface on close

Turns out we never disable the interface. It doesn't really cause
any problems since the channel is off, but it's still better to do it
this way.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

pasemi_mac: add support for setting MTU

Currently keeping it at 1500 bytes or below since jumbo frames need
special checksum offload on TX.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

pasemi_mac: Add support for changing mac address

Straightforward. It used to be hardcoded and impossible to override
with ifconfig.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

S2io: Fix for LRO Bugs

Resubmitting patch from Al Viro <viro@zeniv.linux.org.uk>, with subject -
[PATCH] s2io LRO bugs.
a) initiate_new_session() sets ->tcp_ack to ntohl(...); everything
   else stores and expects to find there the net-endian value.
b) check for monotonic timestamps in verify_l3_l4_lro_capable()
   compares the value sitting in TCP option (right there in the skb->data,
   net-endian 32bit) with the value picked from earlier packet.
   Doing that without ntohl() is an interesting idea and it might even
   work occasionally; unfortunately, it's quite broken.

Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

PHYLIB: Add BCM5482 PHY support

This Broadcom PHY is similar to other bcm54xx devices.

Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: add new wakeup cababilities

Ethtool supports wake-on-ARP and wake-on-link, and so does the hardware
supported by e1000e.  This patch just introduces the two.

Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

big-endian support for via-velocity

* kill bitfields
* annotate
* add missing conversions
* fix a couple of brainos in zerocopy stuff (fortunately, it's ifdef'ed out)

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtl8150: use default MTU of 1500

The RTL8150 driver uses an MTU of 1540 by default, which causes a
bunch of problems -- it prevents booting from NFS root, for one.

Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/sunbmac.c section fix

This patch fixes the following section mismatch:

<--  snip  -->

...
WARNING: drivers/net/sunbmac.o(.devinit.text+0x24): Section mismatch in reference from the function bigmac_sbus_probe() to the function .init.text:bigmac_ether_init()
...

<--  snip  -->

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/sunqe.c section fix

This patch fixes the following section mismatch:

<--  snip  -->

...
WARNING: drivers/net/sunqe.o(.devinit.text+0x4): Section mismatch in reference from the function qec_sbus_probe() to the function .init.text:qec_ether_init()
...

<--  snip  -->

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/sunvnet.c:print_version() must be __devinit

This patch fixes the following section mismatches:

<--  snip  -->

...
WARNING: drivers/net/sunvnet.o(.text+0x220): Section mismatch in reference from the function print_version() to the variable .devinit.data:version
WARNING: drivers/net/sunvnet.o(.text+0x228): Section mismatch in reference from the function print_version() to the variable .devinit.data:version
...

<--  snip  -->

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

IBMLANA no longer has to depend on MCA_LEGACY

This patch removes the no longer required dependency of IBMLANA
on MCA_LEGACY.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ibmlana_init_one() must be __devinit

This patch fixes the following section mismatch:

<--  snip  -->

...
WARNING: drivers/net/built-in.o(.text+0x1148a5): Section mismatch in reference from the function ibmlana_init_one() to the variable .init.data:ibmlana_adapter_names
...

<--  snip  -->

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

olympic_open() must be __devinit

This patch fixes the following section mismatch:

<--  snip  -->

...
WARNING: drivers/net/built-in.o(.text+0x155573): Section mismatch in reference from the function olympic_open() to the function .devinit.text:olympic_init()
...

<--  snip  -->

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ibmlana_adapter_names[] must be __devinitdata

This patch fixes the following section mismatch:

<--  snip  -->

...
WARNING: drivers/net/built-in.o(.devinit.text+0x1baa4): Section mismatch in reference from the function ibmlana_init_one() to the variable .init.data:ibmlana_adapter_names
...

<--  snip  -->

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

via-rhine.c:rhine_hw_init() must be __devinit

Thie patch fixes the following section mismatch:

<--  snip  -->

...
WARNING: drivers/net/built-in.o(.text+0xdd840): Section mismatch in reference from the function rhine_hw_init() to the function .devinit.text:rhine_reload_eeprom()
...

<--  snip  -->

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

NET: AX88796 use dev_dbg() instead of printk()

Change to using dev_dbg() and the other dev_xxx()
macros instead of printk, and update to use the
print_mac() helper.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

macb: Fix section mismatch and shrink runtime footprint

macb devices are only found integrated on SoCs, so they can't be
hotplugged. Thus, the probe() and exit() functions can be __init and
__exit, respectively. By using platform_driver_probe() instead of
platform_driver_register(), there won't be any references to the
discarded probe() function after the driver has loaded.

This also fixes a section mismatch due to macb_probe(), defined as
__devinit, calling macb_get_hwaddr, defined as __init.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ehea: fix sysfs link compile problem

Due to changes in the struct device_driver there is no direct
access to its kobj any longer. The kobj was used to create
sysfs links between eHEA ethernet devices and the driver.
This patch removes the affected sysfs links to resolve
the build problems.

Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ucc_geth: add support for netpoll

This patch adds netpoll support for the QE UCC Gigabit Ethernet
driver. Tested using netconsole and KGDBoE.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ucc_geth: fix module removal

- uccf should be set to NULL to not double-free memory on
  subsequent calls;
- ind_hash_q and group_hash_q lists should be initialized in the
  probe() function, instead of struct_init() (called by open()),
  otherwise there will be an oops if ucc_geth_driver removed
  prior 'ifconfig ethX up';
- add unregister_netdev();
- reorder geth_remove() steps.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ehea: fix qmr checkpatch complaints

Cc: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Doug Maxey <dwm@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ehea: fix phyp checkpatch complaints

Cc: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Doug Maxey <dwm@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ehea: fix main checkpatch complaints

Cc: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Doug Maxey <dwm@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ehea: fix ethtool checkpatch complaints

Cc: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Doug Maxey <dwm@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ehea: fix ehea.h checkpatch complaints

Cc: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Doug Maxey <dwm@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge git://git./linux/kernel/git/bart/ide-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (95 commits)
  ide-tape: remove idetape_config_t typedef
  ide-tape: remove mtio.h related comments
  ide-tape: make function name more accurate
  ide-tape: remove unused sense packet commands.
  ide-tape: use generic byteorder macros
  ide-tape: remove EXPERIMENTAL driver status
  ide-tape: use generic scsi commands
  ide-tape: remove struct idetape_block_size_page_t
  ide-tape: remove structs os_partition_t, os_dat_entry_t, os_dat_t
  ide-tape: remove struct idetape_parameter_block_descriptor_t
  ide-tape: remove struct idetape_medium_partition_page_t
  ide-tape: remove struct idetape_data_compression_page_t
  ide-tape: remove struct idetape_inquiry_result_t
  ide-tape: remove struct idetape_capabilities_page_t
  ide-tape: remove IDETAPE_DEBUG_BUGS
  ide-tape: remove IDETAPE_DEBUG_INFO
  ide-tape: dump gcw fields on error in idetape_identify_device()
  ide-tape: remove struct idetape_mode_parameter_header_t
  ide-tape: remove struct idetape_request_sense_result_t
  ide-tape: remove dead code
  ...

fix writev regression: pan hanging unkillable and un-straceable

Frederik Himpe reported an unkillable and un-straceable pan process.

Zero length iovecs can go into an infinite loop in writev, because the
iovec iterator does not always advance over them.

The sequence required to trigger this is not trivial. I think it
requires that a zero-length iovec be followed by a non-zero-length iovec
which causes a pagefault in the atomic usercopy. This causes the writev
code to drop back into single-segment copy mode, which then tries to
copy the 0 bytes of the zero-length iovec; a zero length copy looks like
a failure though, so it loops.

Put a test into iov_iter_advance to catch zero-length iovecs. We could
just put the test in the fallback path, but I feel it is more robust to
skip over zero-length iovecs throughout the code (iovec iterator may be
used in filesystems too, so it should be robust).

Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'for-linus' of git://git./linux/kernel/git/ieee1394/linux1394-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  ieee1394: sbp2: fix bogus s/g access change

ide-tape: remove idetape_config_t typedef

Since this is used only in idetape_blkdev_ioctl(), remove the typedef and make
the struct function-local.

Bart:
- s/sizeof(struct idetape_config)/sizeof(config)/

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-tape: remove mtio.h related comments

Those are already in mtio.h.

Bart:
- undo 'unsigned int/unsigned long' -> 'uint/ulong' conversion

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-tape: make function name more accurate

idetape_active_next_stage() was rather ambiguous wrt its purpose. Make that
more explicit and remove superfluous comment.

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-tape: remove unused sense packet commands.

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-tape: use generic byteorder macros

This is not a network driver.

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-tape: remove EXPERIMENTAL driver status

ide-tape has depended on EXPERIMENTAL for ages. Change that since the driver is
being only maintained now.

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-tape: use generic scsi commands

Also, remove those which weren't used.

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-tape: remove struct idetape_block_size_page_t

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-tape: remove structs os_partition_t, os_dat_entry_t, os_dat_t

They seem just to sit there completely unused.

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-tape: remove struct idetape_parameter_block_descriptor_t

Also, shorten function name idetape_get_blocksize_from_block_descriptor() and
move its definition up thereby getting rid of its forward declaration.

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-tape: remove struct idetape_medium_partition_page_t

There should be no functional changes resulting from this patch.

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-tape: remove struct idetape_data_compression_page_t

There should be no functional changes resulting from this patch.

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-tape: remove struct idetape_inquiry_result_t

There should be no functional changes resulting from this patch.

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-tape: remove struct idetape_capabilities_page_t

All those 2-byte values denoting the different capabilities are being written to
the local copy of the caps buffer without being converted to big endian for
simplicity of usage and shorter code later.  Also, we add some comments stating
which are the fields of the caps page in question in order to alleviate the
cryptic pointer casting exercises as in e.g. idetape_get_mode_sense_results().

There should be no functional changes resulting from this patch.

Bart:
- remove two needless "!!"

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-tape: remove IDETAPE_DEBUG_BUGS

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-tape: remove IDETAPE_DEBUG_INFO

The device capabilities are probed for during device initialization so this
info is available through proc/ioctl() und it is redundant here.

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-tape: dump gcw fields on error in idetape_identify_device()

Cc: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-tape: remove struct idetape_mode_parameter_header_t

Bart:
- remove 'capabilities->speed' chunk
- re-add brackets to block_descrp assignment

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-tape: remove struct idetape_request_sense_result_t

Bart:
- remove unnecessary comment change
- remove two needless "!!"

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-tape: remove dead code

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-tape: move historical changelog to Documentation/ide/ChangeLog.ide-tape.1995-2002

Also, cleanup whitespace and update comments.

Bart:
- remove reference to drivers/block/ide.c
- move driver documentation to Documentation/ide/ide-tape.txt

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-cs: use ide_std_init_ports()

No reason to use ide_init_hwif_ports() in ide-cs (as a nice side-effect
this makes ide-cs work on archs that don't define IDE_ARCH_OBSOLETE_INIT).

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: move check_dma_crc() to ide-dma.c

* Move check_dma_crc() to ide-dma.c and add inline version for
  CONFIG_BLK_DEV_IDEDMA=n case.

* Rename check_dma_crc() to ide_check_dma_crc().

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: remove ide_auto_reduce_xfer()

While at it:

* Remove needless '!drive->crc_count' check.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: move drive->crc_count check out from check_dma_crc()

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: remove ide_ata66_check()

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: remove set_transfer()

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: unexport SELECT_DRIVE()

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-scsi: remove needless SELECT_DRIVE() call

SELECT_DRIVE() is called by IDE core code in start_request() before device
driver's ->do_request method.  In ide-scsi case ->do_request is implemented
by idescsi_do_request() which is also the only user of idescsi_issue_pc().

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: use __ide_set_handler() in ide_execute_command()

* Use __ide_set_handler() in ide_execute_command().

While at it:

* Fix whitespace damage in ide_execute_command().

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: remove SATA_*_REG macros

* siimage.c: use hwif->sata_scr[SATA_{ERROR,STATUS}_OFFSET] instead of
  SATA_{ERROR,STATUS}_REG macros.

* Remove no longer needed SATA_*_REG macros.

While at it:

* Remove needless SATA Status register read from sil_sata_reset_poll().

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: remove ->nice0 and ->nice2 fields from ide_drive_t

* ->nice0 and ->nice2 ide_drive_t fields are always zero so remove them.

* IDE_NICE_0 and IDE_NICE_2 defines from <linux/hdreg.h> are no longer
  used by any kernel code so cover them with #ifndef/#endif __KERNEL__.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: convert ->straight8 field in ide_hwif_t to bit flag

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: remove unused ->auto_poll field from ide_hwif_t

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-probe: remove needless Status register reads

* Cache value read from the Status register in 'stat' variable in do_probe()
  and enable_nest(), then remove remove needless Status register reads.

While at it:

* Add proper KERN_* levels to printk() calls.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-cris: use ide_execute_command()

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

trm290: use ide_execute_command()

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-scsi: use ide_execute_command()

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-tape: use ide_execute_command()

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: move create_proc_ide_drives() call to ide_device_add_all()

* Un-static create_proc_ide_drives() and call it from ide_device_add_all().

While at it:
* Rename create_proc_ide_drives() to ide_proc_port_register_devices().

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: move hwif->present check out from ide_proc_register_port()

Move hwif->present check out from ide_proc_register_port() to
ide_device_add_all().

There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: factor out devices setup from ide_acpi_init()

* Factor out devices setup from ide_acpi_init() to
  ide_acpi_port_init_devices().

* Call ide_acpi_port_init_devices() in ide_device_add_all().

While at it:
* Remove no longer needed 'drive' field from struct ide_acpi_drive_link.

There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-acpi: remove dead code from do_drive_get_GTF()

These pointers are always setup in ide_acpi_init().

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-acpi: remove needless exports

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: move ide_acpi_init() call to ide_device_add_all()

There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: factor out devices setup from init_irq()

* Factor out devices setup from init_irq() to ide_port_setup_devices().

While at it:
* Do devices setup after printing port information.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: factor out adding drive to hwgroup from init_irq()

Factor out adding drive to hwgroup from init_irq() to
ide_add_drive_to_hwgroup().

There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: move hwif->rqsize init from ide_init_queue() to init_irq()

Move hwif->rqsize init from ide_init_queue() to init_irq().

There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>