drm/i915: s/is_sdvob/enum port/

Replace the is_sdvob bool and some sdvo_reg checks with enum port. This
makes the SDVO code look more modern, and gets rid of explicit register
offset checks in the code which will hamper register type checking.

v2: Add assert_sdvo_port_valid() (Chris)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1446838199-3666-1-git-send-email-ville.syrjala@linux.intel.com

drm/i915: s/PCH_DP_/PORT_/ in intel_trans_dp_port_sel() and move it next to its only user

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446672017-24497-9-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

pci: Decouple quirks.c from i915_reg.h

i915 register defines are going to become type safe, so going forward
the register defines can't be used as straight numbers. Since quirks.c
needs just a few extra register defines from i915_reg.h, decouple the
two by defining the required registers locally in quirks.c. This was
already done for a few other igpu related registers.

Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446672017-24497-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Rely on TEST_SINK_START instead of tracking Sink CRC state on dev_priv.

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Stop tracking last calculated Sink CRC.

It was created at 'commit aabc95dcf20 (drm/i915: Dont -ETIMEDOUT
on identical new and previous (count, crc).")' becase the counter
wasn't reliable.

Now that we properly wait for the counter to be reset we can rely
a bit more in the counter.

Also that patch stopped to return -ETIMEDOUT so the test case is
unable to skip when it is unreliable and end up in many fails
that should be skip instead.

So, with the counter more reliable we can remove
this hack that just makes things more confusing when test cases
are really expecting the same CRC and let test case skip if that's
not the case.

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Make Sink crc calculation waiting for counter to reset.

According to VESA DP spec TEST_CRC_COUNT (Bits 3:0) at
TEST_SINK_MISC (00246h) is "Reset to 0 when TEST_SINK bit 0 = 0;

So let's give few vblanks so we are really sure that this counter
is really zeroed on the next sink_crc read.

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Allow 1 vblank to let Sink CRC calculation to start or stop.

According to VESA DP Spec, setting TEST_SINK_START (bit 0)
of TEST_SINK (00270h) "Stop/Start calculating CRC on the next frame"

So let's wait at least 1 vblank to really say the calculation
stopped or started.

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/skl: Remove unused suspend and resume callbacks

Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447084107-8521-13-git-send-email-patrik.jakobsson@linux.intel.com

drm/i915/gen9: Add boot parameter for disabling DC6

v2: Use _unsafe (Jani)
v3: Allow specifying specific DC-states instead of just DC6 (Imre)

Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447682467-6237-3-git-send-email-patrik.jakobsson@linux.intel.com

drm/i915/gen9: Turn DC handling into a power well

Handle DC off as a power well where enabling the power well will prevent
the DMC to enter selected DC states (required around modesets and Aux
A). Disabling the power well will allow DC states again. For now the
highest DC state is DC6 for Skylake and DC5 for Broxton but will be
configurable for Skylake in a later patch.

v2: Check both DC5 and DC6 bits in power well enabled function (Ville)
v3:
- Remove unneeded DC_OFF case in skl_set_power_well() (Imre)
- Add PW2 dependency to DC_OFF (Imre)
v4: Put DC_OFF before PW2 in BXT power well array

Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[fixed line over 80 and parenthesis alignment checkpatch warns (imre)]
Link: http://patchwork.freedesktop.org/patch/msgid/1447687201-24759-1-git-send-email-patrik.jakobsson@linux.intel.com

drm/i915: Explain usage of power well IDs vs bit groups

v2: Add explanation of the fixed power well bits (Imre)

Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447682467-6237-2-git-send-email-patrik.jakobsson@linux.intel.com

drm/i915: Do not warn on PG2 enabled in gen9_disable_dc5()

PG2 enabled is not a requirement for disabling DC5. It's just one
of the reasons why the DMC wouldn't enter DC5. During modeset we don't
care about PG2 from a DC perspective, only the fact that DC5/DC6 is not
allowed.

Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447084107-8521-9-git-send-email-patrik.jakobsson@linux.intel.com

drm/i915: Add a modeset power domain

We need a power domain for disabling DC5/DC6 around modesets to prevent
confusing the DMC.

Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447084107-8521-8-git-send-email-patrik.jakobsson@linux.intel.com

drm/i915: Remove distinction between DDI 2 vs 4 lanes

We never make use of the distinction between 2 vs 4 lanes so combine
them into a per port domain instead. This saves us a few bits in the
power domain mask. Change suggested by Ville.

Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447084107-8521-7-git-send-email-patrik.jakobsson@linux.intel.com

drm/i915: Remove DDI power domain exclusion SKL_DISPLAY_ALWAYS_ON_POWER_DOMAINS

All the DDI power domains are already excluded from
SKL_DISPLAY_ALWAYS_ON_POWER_DOMAINS on account of
excluding SKL_DISPLAY_POWERWELL_1_POWER_DOMAINS and
SKL_DISPLAY_POWERWELL_2_POWER_DOMAINS, no need to spell them out again.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447084107-8521-6-git-send-email-patrik.jakobsson@linux.intel.com

drm/i915: Introduce a gmbus power domain

Currently the gmbus code uses intel_aux_display_runtime_get/put in an
effort to make sure the hardware is powered up sufficiently for gmbus.
That function only takes the runtime PM reference which on VLV/CHV/BXT
is not enough. We need the disp2d/pipe-a well on VLV/CHV and power well
2 on BXT. So add a new power domnain for gmbus and kill off the now
unused intel_aux_display_runtime_get/put. And change
intel_hdmi_set_edid() to use the gmbus power domain too since that's all
we need there.

Also toss in a BUILD_BUG_ON() to catch problems if we run out of
bits for power domains. We're already really close to the limit...

[Patrik: Add gmbus string to debugfs output]

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447084107-8521-5-git-send-email-patrik.jakobsson@linux.intel.com

drm/i915: Clean up AUX power domain handling

Introduce intel_display_port_aux_power_domain() which simply returns
the appropriate AUX power domain for a specific port, and then replace
the intel_display_port_power_domain() with calls to the new function
in the DP code. As long as we're not actually enabling the port we don't
need the lane power domains, and those are handled now purely from
modeset_update_crtc_power_domains().

My initial motivation for this was to see if I could keep the DPIO power
wells powered down while doing AUX on CHV, but turns out I can't so this
doesn't change anything for CHV at least. But I think it's still a
worthwile change.

v2: Add case for PORT E. Default to POWER_DOMAIN_AUX_D for now. (Ville)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447682467-6237-1-git-send-email-patrik.jakobsson@linux.intel.com

drm/i915/gen9: Always set mask memory up when enabling DC5 or DC6

Move call to gen9_set_dc_state_debugmask_memory_up() into
gen9_set_dc_state() to prevent us missing it somewhere.

Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447084107-8521-3-git-send-email-patrik.jakobsson@linux.intel.com

drm/i915: Don't trust CSR program memory contents

Replaces "drm/i915: Force loading of csr program at boot" in the old
series.

Previously we called blindly into intel_csr_load_program() and depended
on a check of whether the CSR program memory was cleared or not.
This check is not reliable and no longer needed since we fixed the
call-sites of intel_csr_load_program().

Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447084107-8521-2-git-send-email-patrik.jakobsson@linux.intel.com

drm/i915: fix handling of the disable_power_well module option

When this option is 0 (so the power well support is disabled) we are
supposed to enable all power wells once and don't disable them unless we
system suspend the device. Currently if the option is 0, we can call the
power well enable handlers multiple times, whenever their refcount
changes from 0->1. This may not be a problem for the HW, but it's not
logical and may trigger some warnings in the power well code which
doesn't expect this. So simply keep around a reference while we are
not system suspended to solve this. For simplicity mark the module
option read only, so we don't need to deal with re-enabling the feature
during runtime. If someone really needs that it could be added later in
a more proper way.

v2:
- fix typo in comment in intel_power_domains_suspend() (Patrik)

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447775063-24438-1-git-send-email-imre.deak@intel.com

drm/i915/skl: remove redundant DDI/IRQ reinitialization during PW1 enabling

We don't need to reinit DDI and IRQs during PW1 enabling any more, since
we don't toggle PW1 on-demand any more. We enable PW1 only as part of
the display core init sequence and after this we initialize both DDI and
IRQs later in the init sequence. So remove these init steps from the
power well code.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-11-git-send-email-imre.deak@intel.com

drm/i915/skl: make sure LCPLL is disabled when uniniting CDCLK

Suppressing LCPLL disabling was added to avoid interfering with the DMC
firmware. It is not needed any more since we uninit CDCLK now with the
DMC deactivated (DC states disabled). We also must disable it during system
suspend as part of the Bspec "Display uninit sequence".

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-10-git-send-email-imre.deak@intel.com

drm/i915/skl: disable DC states before display core init/uninit

We need to disable the DC states during display core init to sanitize
the HW state we inherit from the BIOS. We need to disable it during
display core uninit too, since the power well framework will leave it
enabled (since we get to the display core uninit step with all power
domains disabled already).

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-9-git-send-email-imre.deak@intel.com

drm/i915/gen9: simplify DC toggling code

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
[fix line over 80 chars checkpatch WARN in gen9_set_dc_state() (imre)]
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-8-git-send-email-imre.deak@intel.com

drm/i915/skl: don't toggle PW1 and MISC power wells on-demand

With the DMC firmware installed we don't need to handle HW resources
that are handled automatically by the firmware. Besides being redundant
this can also interfere with the firmware, possibly getting it into a
broken/blocked state. The on-demand handling of PW1 was already half-way
removed, MISC IO was still handled in this way. After the last patch we
init/uninit these HW resources manually as part of the display core
init/uninit sequence, so we can now remove the on-demand handling for
these completely.

We still keep around the power wells (with no domains attached to them)
since the manual toggling during display core init/uninit happens via
the current API.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
[s/beeing/being/ in commit message (imre)]
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-7-git-send-email-imre.deak@intel.com

drm/i915/skl: init/uninit display core as part of the HW power domain state

We need to initialize the display core part early, before initializing
the rest of the display power state. This is also described in the bspec
termed "Display initialization sequence". Atm we run this sequence
during driver loading after power domain HW state initialization which
is too late and during runtime suspend/resume which is unneeded and can
interere with DMC functionality which handles HW resources toggled
by this init/uninit sequence automatically. The init sequence must be
run as the first step of HW power state initialization and during
system resume. The uninit sequence must be run during system suspend.

To address the above move the init sequence to the initial HW power
state setup and the uninit sequence to a new power domains suspend
function called during system suspend.

As part of the init sequence we also have to reprogram the DMC firmware
as it's lost across a system suspend/resume cycle.

After this change CD clock initialization during driver loading will
happen only later after other dependent HW/SW parts are initialized,
while during system resume it will get initialized as the last step of
the init sequence. This distinction can be removed by some refactoring
of platform independent parts. I left this refactoring out from this
series since I didn't want to change non-SKL parts. This is a TODO for
later.

v2:
- fix error path in i915_drm_suspend_late()
- don't try to re-program the DMC firmware if it failed to load

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447774433-20834-1-git-send-email-imre.deak@intel.com

drm/i915: rename intel_power_domains_resume to *_sync_hw

Give a more proper name to this function.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-5-git-send-email-imre.deak@intel.com

drm/i915: Make turning on/off PW1 and Misc I/O part of the init/fini sequences

Before this patch, we used the intel_display_power_{get,put} functions
to make sure the PW1 and Misc I/O power wells were enabled all the
time while LCPLL was enabled. We called a get() at
intel_ddi_pll_init() when we discovered that LCPLL was enabled, then
we would call put/get at skl_{un,}init_cdclk().

The problem is that skl_uninit_cdclk() is indirectly called by
intel_runtime_suspend(). So it will only release its power well
_after_ we already decided to runtime suspend. But since we only
decide to runtime suspend after all power wells and refcounts are
released, that basically means we will never decide to runtime
suspend.

So what this patch does to fix that problem is move the PW1 + Misc I/O
power well handling out of the runtime PM mechanism: instead of
calling intel_display_power_{get_put} - functions that touch the
refcount -, we'll call the low level intel_power_well_{en,dis}able,
which don't change the refcount. This way, it is now possible for the
refcount to actually reach zero, and we'll now start runtime
suspending/resuming.

v2 (from Paulo):
  - Write a commit message since the original patch left it empty.
  - Rebase after the intel_power_well_{en,dis}able rename.
  - Use lookup_power_well() instead of hardcoded indexes.

Testcase: igt/pm_rpm/rte (and every other rpm test)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92211
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92605
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-4-git-send-email-imre.deak@intel.com

drm/i915: fix lookup_power_well for power wells without any domain

The current lookup code wouldn't find a power well if it's not in any
power domain. There wasn't any power wells before but an upcoming patch
will detach the power domains from power well#1 and the MISC IO power
wells, so fix things up accordingly.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-3-git-send-email-imre.deak@intel.com

drm/i915: fix the power well ID for always on wells

lookup_power_well() expects uniq power well IDs, but atm we have
uninitialized IDs which would clash with those power wells with a 0
ID. This wasn't a problem so far since nothing looked up such a power
well, but an upcoming patch will (Misc IO for SKL), so fix this up on
platforms where this matters.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-2-git-send-email-imre.deak@intel.com

drm/i915: get runtime PM reference around GEM set_tiling IOCTL

After fixing the same issue in the set_caching IOCTL and Chris' request
to check out the possibilities for an improved RPM ref handling I
noticed that we have the same issue in the set_tiling IOCTL. Fix this
up.I didn't see any bug reports about this one, but the GTT unbind
operation on this path accesses the HW, which needs the ref.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447092986-11165-1-git-send-email-imre.deak@intel.com

drm/i915: Serialise updates to GGTT with access through GGTT on Braswell

When accessing through the GTT from one CPU whilst concurrently updating
the GGTT PTEs in another thread, the hardware likes to return random
data. As we have strong serialisation prevent us from modifying the PTE
of an active GTT mmapping, we have to conclude that it whilst modifying
other PTE's that error occurs. (I have not looked for any pattern such
as modifying PTE within the same page or cacheline as active PTE -
though checking whether revoking neighbouring objects should be enough
to test that theory.) The corruption also seems restricted to Braswell
and disappears with maxcpus=0. This patch stops all access through the
GTT by other CPUs when we update any PTE by stopping the machine around
the GGTT update.

Note that splitting up the 64 bit write into two 32 bit writes was
tried and found to fail too.

Testcase: igt/gem_concurrent_blit
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89079
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add note about 2x 32bits failing too.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: force link training when requested by Sink

Compliance test 4.3.1.11 requires source to perform link training
always if the automated test requests for it. This patch
enforces this requirement.

Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Cleanup test data during long/short hotplug

Automated test data that is updated when a test is requested is not cleared
till next automated test request is recevied which can cause various
problems. This patch fixes this by clearing this during the next
short pulse and on hot unplug.

For example, when TEST_LINK_TRAINING is requested it is updated
to appropriate variable inside intel_dp_handle_test_request
but is also cleared only inside the same function. if the next
short pulse does not have the AUTOMATED_TEST_REQUEST bits set
the variable will not be cleared resulting in carrying incorrect
test status in local variables.

v2: Added comments and moved nack and defer variables before set_edid
(Sonika)

Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/skl: Correct other-pipe watermark update condition check (v2)

If ddb allocation for planes in current CRTC is changed, that doesn't
lead to ddb allocation change for other CRTCs, because our DDB allocation
is not dynamic according to plane parameters, ddb is allocated according
to number of CRTC enabled, & divided equally among CTRC's.

In current condition check during Watermark calculation, if number of
plane/ddb allocation changes for current CRTC, Watermark for other pipes
are recalculated. But there is no change in DDB allocation of other pipe
so watermark is also not changed, This leads to warning messages.
WARN_ON(!wm_changed)

This patch corrects this and check if DDB allocation for pipes is changed,
then only recalculate watermarks.

v2 (by Matt): Rebased to latest -nightly and fixed a typo

Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Reviewed-by(v1): Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Model PSR AUX register selection more like the normal AUX code

v2: Split up the ctl vs. data reg handling like in the normal AUX code

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-8-git-send-email-ville.syrjala@linux.intel.com

drm/i915: Add dev_priv->psr_mmio_base

Drop the EDP_PSR_BASE() thing, and just stick the PSR register offset
under dev_priv, like we for DSI and GPIO for example.

TODO: could probably move a bunch of this kind of stuff into the device
info instead...

v2: Drop the spurious whitespace change (Jani)

Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-7-git-send-email-ville.syrjala@linux.intel.com

drm/i915: Store aux data reg offsets in intel_dp->aux_ch_data_reg[]

Rather than computing on demand, store also the aux data reg
offsets under intel_dp.

v2: Duplicate some code to make things less magic (Jani)
v3: Use PORT_B registers for invalid ports in g4x_aux_data_reg()

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-6-git-send-email-ville.syrjala@linux.intel.com

drm/i915: Remove the magic AUX_CTL is at DP + foo tricks

Currently we determine the location of the AUX registers in a confusing
way. First we assume the PCH registers are used always, but then we
override it for everything but HSW/BDW to use DP+0x10. Very confusing.

Let's just make it straightforward and simply add a few functions to
pick the right AUX_CTL based on the DP port.

To deal with VLV/CHV we'll include the display_mmio_offset into the
AUX register defines.

v2: Reorder patches (Chris)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-5-git-send-email-ville.syrjala@linux.intel.com

drm/i915: Parametrize AUX registers

v2: Keep some MISSING_CASE() stuff (Jani)
    s/-1/-PIPE_B/ in the register macro
    Fix typo in patch subject
v3: Use PORT_B registers for invalid ports in g4x_aux_ctl_reg() (Jani)
v4: Reorder patches (Chris)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> (v3)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-4-git-send-email-ville.syrjala@linux.intel.com

drm/i915: Replace the aux ddc name switch statement with kasprintf()

Use kasprintf() to generate the "DPDDC-<port>" name for the aux helper.

To deal with errors properly make intel_dp_aux_init() return something,
and adjust the caller to match. It seems we were also missing a
intel_dp_mst_encoder_cleanup() call on edp (non-port A) init failures,
so add that too.

The whole error/cleanup ordering doesn't feel entirely sane to me, but
I'll leave that part alone for now.

v2: Use kasprintf() instead of a table, reorder patches (Chis)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Replace aux_ch_ctl_reg check with port check

Instead of checking what aux_ch_ctl_reg is, we can simply check the port
when determining the right timeout value to program.

v2: Reorder patches to reduce churn (Chris)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-2-git-send-email-ville.syrjala@linux.intel.com

drm/i915/skl: Update DDI translation tables for SKL

While comparing the B-Spec with the code I noticed that several
values in these tables have been updated in the spec, so I
changed the code to match..

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jim Bride <jim.bride@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446852654-883-1-git-send-email-jim.bride@linux.intel.com

drm/i915: Fix SKL i_boost level

The i_boost level in the DDI translation tables are stored per level.
However, skl_ddi_set_iboos() would choose an entry of that table based
on the port argument.

Cc: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447247754-802-1-git-send-email-ander.conselvan.de.oliveira@intel.com

drm/i915/skl: Removed assert for csr-fw-loading check during disabling dc6

As during disabling dc6 no need to check for csr firmware
loading status, so removed the assert call (Requested by Damien).

Cc: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446069547-24760-14-git-send-email-imre.deak@intel.com

drm/i915/gen9: flush DMC fw loading work during system suspend

Currently during system s/r we enable/disable DC6, so before we do so
make sure that the firmware loading is complete.

Note that whether we need to enable DC6 for S3/S4 is still open.  At
least the firmware program is lost during S3 and we need to reprogram it
after resuming. Until this is clarified we keep the current behavior and
enable/disable DC6.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446069547-24760-13-git-send-email-imre.deak@intel.com

drm/i915/gen9: Use flush_work to synchronize with dmc loader

During driver unload to ensure we dont have any pending task,
flush_work added to complete firmware loading task.

v1: Initial version.

v2: As per review comments from Daniel,
Removed flush_work from skl_set_power_well. As we have taken
power well refernece and rpm count during firmware loading
by using display_power_domain_get/put - this will always
ensure rpm will be blocked if firmware is not loaded.

Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446069547-24760-12-git-send-email-imre.deak@intel.com

drm/i915: Use request_firmware and our own async work

Two benefits:
- We can use FW_LOADER_USERSPACE_FALLBACK.
- We can use flush_work to synchronize with the oustanding worker,
  which is a notch more obvious what it does than having a special
  completion.

The next patch will properly synchronize against the async loader in
the resume and unload code.

Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446069547-24760-11-git-send-email-imre.deak@intel.com

drm/i915/gen9: extract parse_csr_fw

The loader function will get a bit more complicated soon, extract the
parsing code to make the control flow clearer. While doing that just
use dev_priv->csr.dmc_payload as the indicator for whether it all
suceeded or not.

v2-v3:
- unchanged
v4:
- rebased on top of latest drm-intel-nightly

Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
[imre: remove note about BE cast from commit message, it's not relevant
 any more]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
[Jani: fix checkpatch warn on multiple blank lines]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447341089-2735-1-git-send-email-imre.deak@intel.com

drm/i915/gen9: Use dev_priv in csr functions

As all csr firmware related opertion are not using any
any data structures of drm framework level, so better to
use dev_priv instead of dev. it's a new style! :)

Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446069547-24760-9-git-send-email-imre.deak@intel.com

drm/i915/gen9: Don't try to load garbage dmc firmware on resume

We need to make sure we don't put garbage into the hw if dmc firmware
loading failed mid-thru.

Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446069547-24760-8-git-send-email-imre.deak@intel.com

drm/i915/gen9: Simplify csr loading failure printing.

If we really want to we can be more verbose here, but we really don't
need an entire function for this.

Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446069547-24760-7-git-send-email-imre.deak@intel.com

drm/i915/gen9: Align line continuations in intel_csr.c.

Standard is to align continuations of parameter lists and if
conditions to the opening ( in i915 and drm code.

Apply this across the entire file since it was sticking out a bit too
much.

Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
[imre: removed note about reg definitions from the commit message, it's
 not relevant any more]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446069547-24760-6-git-send-email-imre.deak@intel.com

drm/i915/gen9: Remove csr.state, csr_lock and related code.

This removes two anti-patterns:
- Locking shouldn't be used to synchronize with async work (of any
  form, whether callbacks, workers or other threads). This is what the
  mutex_lock/unlock seems to have been for in intel_csr_load_program.
  Instead ordering should be ensured with the generic
  wait_for_completion()/complete(). Or more specific functions
  provided by the core kernel like e.g.
  flush_work()/cancel_work_sync() in the case of synchronizing with a
  work item.

- Don't invent own completion like the following code did with the
  (already removed) wait_for(csr_load_status_get()) pattern - it's
  really hard to get these right when you want them to be _really_
  correct (and be fast) in all cases. Furthermore it's easier to read
  code using the well-known primitives than new ones using
  non-standard names.

Before enabling/disabling DC6 check if the firmware is loaded
successfully. This is guaranteed during runtime s/r, since otherwise we
don't enable RPM, but not during system s/r.

Note that it's still unclear whether we need to enable/disable DC6
during system s/r, until that's clarified, keep the current behavior and
enable/disable DC6.

Also after this patch there is a race during system s/r where the
firmware may not be loaded yet, that's addressed in an upcoming patch.

v2-v3:
- unchanged
v4:
- rebased on latest drm-intel-nightly

Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
[imre: added code and note about checking if the firmware loaded ok,
 before enabling/disabling it]
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447341037-2623-1-git-send-email-imre.deak@intel.com

drm/i915/gen9: move assert_csr_loaded into intel_rpm.c

Avoids non-static functions since all the callers are in intel_rpm.c.

Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
[imre: removed note about reg definitions from commit message, since
 it's not relevant any more]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
[Jani: make assert_csr_loaded static]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446069547-24760-4-git-send-email-imre.deak@intel.com

drm/i915: use correct power domain for csr loading

Grabbing a runtime pm reference with intel_runtime_pm_get will only
prevent device D3. But dmc firmware is required even earlier (namely
for the skl power well 2).

Hence we need to grab a rpm reference higher up in the hierarchy. For
simplicity just grab the _INIT display power well. That's a bit too
much, but since the firmware loading task should completely fairly
quickly this won't be a real problem really.

Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446069547-24760-3-git-send-email-imre.deak@intel.com

drm/i915/gen9: csr_init after runtime pm enable

Skl is fully dependent on dmc for going to low power state (dc5/dc6).
This requires a trigger from rpm. To ensure the dmc firmware
is available for runtime pm support rpm-reference-count is used
by not releasing the rpm reference if firmware loading is
not completed.

So moved the intel_csr_ucode_init call after runtime pm enable.

Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
[imre: moved the call right after power domain init to avoid race with
 the console modesetting]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Reviewed-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446069547-24760-2-git-send-email-imre.deak@intel.com

drm/i915: refactor stepping info retrieval

Have only one if ladder for platforms and only one range check for
size. Makes it easier to handle new platforms. Remove the use of
negative return values in char, which might underflow to be positive for
some negative error codes.

Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445344713-1407-3-git-send-email-jani.nikula@intel.com

drm/i915: constify bxt stepping info

Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445344713-1407-2-git-send-email-jani.nikula@intel.com

drm/i915: fix indentation on skl stepping info

Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445344713-1407-1-git-send-email-jani.nikula@intel.com

drm/i915: Remove redundant check in i915_gem_obj_to_vma

No need to verify VMA belongs to GGTT since:

1. The function must return a normal VMA belonging to passed in VM.
2. There can only be one normal VMA for any VM.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447329595-17495-1-git-send-email-tvrtko.ursulin@linux.intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Clean up LVDS register handling harder

Minor fixup to d0669d007542 ("drm/i915: Clean up LVDS register
handling") which intended to read lvds_reg just once at the
beginning of intel_lvds_init() and use that throughout the rest
of the function but accidentally missed one register readout.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: http://patchwork.freedesktop.org/patch/msgid/20151107141244.AB7616E242@gabe.freedesktop.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Move the fbdev async_schedule() into intel_fbdev.c

Reading the driver load/unload code leaves one confused as there's
an async_schedule() in the load, but not async_synchronize_full()
in sight. In fact it's hidden inside intel_fbdev.c. So let's move the
async_schedule() into intel_fbdev.c as well so that it's next to the
async_synchronize_full(), which should make the relationship easier
to see.

Plus this way we won't schedule a nop function call when fbdev is
disabled. And we were passing a pointer to a static inline
function to async_schedule(), which seems rather dubious to me.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446815313-9490-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Do fbdev fini first during unload

We set up fbdev last during load, so doing the fbdev cleanup should be
first.

We weren't supposed to drop the init power during driver unload, but since
the fbdev teardown happened after intel_power_domains_fini() that could
have happened due in one of two ways. First it could have happened
during the modeset caused by normal fbdev cleanup. But in addition it
could have happened already via the intel_fbdev_initial_config() since
that is executed asynhronously, and the async_synchronize_full() was
done during fbdev cleanup, after intel_power_domains_fini(). All of
that got eliminated by
commit 292b990e86abc ("drm/i915: Update power domains on readout.")
since we now drop the init power synchronously during driver load.

So there is no real bug wrt. the init power anymore, but still it seems
better to do the fbdev cleanup first, before we've potentially cleaned
up something else important.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446815313-9490-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Kill intel_runtime_pm_disable()

intel_runtime_pm_disable() takes an extra rpm reference which combined
with the one we leak from intel_display_set_init_power() leaves the
usage count at <original>+1 after the driver has been unloaded.
The original ref is dropped explicitly in intel_runtime_pm_enable().
So the next time we load the driver we can no longer do runtime PM ever.

This used to work, but
commit 292b990e86ab ("drm/i915: Update power domains on readout.")
broke things by not dropping the init power domain during fbdev
teardown. Based on the comment in intel_power_domains_fini(), the
way it used to to work wasn't intentional. As in we weren't supposed
to drop the init power during driver unload. And since we no longer
do, we now leak an extra rpm reference.

So fix things by throwing intel_runtime_pm_disable() to the bin, so
that the only leaked reference comes from the init power domain.

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Stone <daniels@collabora.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Fixes: 292b990e86ab ("drm/i915: Update power domains on readout.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446815313-9490-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>

drm/i915: Setup DDI clk for MST on SKL

Set up the DDI->PLL mapping on SKL also for MST links. Might help make
MST operational on SKL.

v2: Rebased due to KBL
    Improve the patch subject, Jesse provided the new one

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1439826380-18403-1-git-send-email-ville.syrjala@linux.intel.com
References: https://bugs.freedesktop.org/show_bug.cgi?id=91791
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>

drm/i915: Configure eDP PLL freq from ironlake_edp_pll_on()

ironlake_set_pll_cpu_edp() only gets called just before
ironlake_edp_pll_on(), so just pull the code into ironlake_edp_pll_on().

Also toss in a debug print into ironlake_edp_pll_off() to match the one
we have in ironlake_edp_pll_on().

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446146763-31821-15-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Use intel_dp->DP in eDP PLL setup

Use intel_dp->DP in the eDP PLL setup, instead of doing RMWs.

To do this we need to move DP_AUDIO_OUTPUT_ENABLE setup to happen later,
so that we don't enable audio accidentally while configuring the PLL.

Note that actually we already enabled audio before the port due to
the double port register write magic required by VLV/CHV from
7b713f50d78b6 ("drm/i915: Fix eDP link training when switching pipes on VLV/CHV")
So that gets changed now to keep audio off as long as the port is off.

Also intel_dp_link_down() must be made to update intel_dp->DP so that we
don't re-enable the port by accident when turning off the PLL. This is
safe now that we don't call intel_dp_link_down() during link retraining.

v2: Add a note about the audio vs. port enable (Daniel)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447164977-32315-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Clean up eDP PLL state asserts

Rewrite the eDP PLL state asserts to conform to our usual state assert
style.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446146763-31821-13-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Remove ILK-A eDP PLL workaround notes

We don't care about ILK-A and the old w/a notes may just confuse
people, so get rid of them.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446146763-31821-12-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>

drm/i915: s/DP_PLL_FREQ_160MHZ/DP_PLL_FREQ_162MHZ/

The DP link frequency is 162MHz, not 160MHz. Rename the ILK eDP PLL
defines to match.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446146763-31821-11-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Hide underruns from eDP PLL and port enable on ILK

We get underruns on the other pipe when enabling the CPU eDP PLL and
port on ILK.

Bspec knows about the PLL issue, and recommends doing a vblank wait just
prior to enabling the PLL. That does seem to help, but unfortunately we
get another underrun when actually enabling the CPU eDP port. Bspec
doesn't mention that at all, and the same vblank wait trick doesn't
appear to be effective there.

Since I have no better clue how to deal with this, just hide the errors.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446146763-31821-10-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>

drm/i915: Disable FIFO underrun reporting around IBX transcoder B workaround

Doing the IBX transcoder B workaround causes underruns on
pipe/transcoder A. Just hide them by disabling underrun reporting for
pipe A around the workaround.

It might be possible to avoid the underruns by moving the workaround
to be applied only when enabling pipe A. But I was too lazy to try it
right now, and the current method has been proven to work, so didn't
want to change it too hastily.

Note that this can re-enable underrun reporting on pipe A if was
already disabled due to a previous actual underrun. But that's OK, we
may just get a second underrun report if another real underron occurrs
on pipe A.

v2: Note that pipe A underruns can get re-enabled due to this (Jani)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1446225802-11180-1-git-send-email-ville.syrjala@linux.intel.com

drm/i915: Check for CPT and not !IBX in ironlake_disable_pch_transcoder()

ironlake_enaable_pch_transcoder() checks for CPT to see if it should
enable the timing override chicken bit, but
ironlake_disable_pch_transcoder() checks for !IBX to see if it should
clear the same bit. Change ironlake_disable_pch_transcoder() to check
for CPT as well to keep the two sides consistent.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446146763-31821-8-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>

drm/i915: Check for FIFO underruns after modeset on IVB/HSW and CPT/PPT

Due to the shared error interrupt on IVB/HSW and CPT/PPT we may not
always get an interrupt on a FIFO underrun. But we can always do an
explicit check (like we do on GMCH platforms that have no underrun
interrupt).

v2: Drop stale kerneldoc for i9xx_check_fifo_underruns() (Daniel)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1446225741-11070-1-git-send-email-ville.syrjala@linux.intel.com

drm/i915: Re-enable PCH FIO underrun reporting after pipe has been disabled

Some hardware (IVB/HSW and CPT/PPT) have a shared error interrupt for
all the relevant underrun bits, so in order to keep the error interrupt
enabled, we need to have underrun reporting enabled on all PCH
transocders. Currently we leave the underrun reporting disabled when
the pipe is off, which means we won't get any underrun interrupts
when only a subset of the pipes are active.

Fix the problem by re-enabling the underrun reporting after the pipe has
been disabled. And to avoid the spurious underruns during pipe enable,
disable the underrun reporting before embarking on the pipe enable
sequence. So this way we have the error reporting disabled while
running through the modeset sequence.

v2: Re-enable PCH FIFO underrun reporting unconditionally on pre-HSW

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1446225691-10928-1-git-send-email-ville.syrjala@linux.intel.com

drm/i915: Enable PCH FIFO underruns later on HSW+

As we did for ILK/SNB/IVB, move the PCH FIFO underrun enable to happen
after the encoder enable on HSW+. And again, for symmetry, move the
the disable to happen before encoder disable.

I've left out the vblank wait before the enable here because I don't
know if it's needed or not. Actually I don't know if this entire
change is needed as I don't have a HSW/BDW with VGA output.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446146763-31821-5-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>

drm/i915: Enable PCH FIFO underruns later on ILK/SNB/IVB

We get spurious PCH FIFO underruns if we enable the reporting too soon
after enabling the crtc. Move it to be the last step, after the encoder
enable. Additionally we need an extra vblank wait, otherwise we still
get the underruns. Presumably the pipe/fdi isn't yet fully up and running
otherwise.

For symmetry, disable the PCH underrun reporting as the first thing,
just before encoder disable, when shutting down the crtc.

v2: Do the PCH underrun enable unconditionally (Jani, Daniel)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1446225627-10809-1-git-send-email-ville.syrjala@linux.intel.com

drm/i915: Set sync polarity from adjusted mode for TRANS_DP_CTL

Rather than looking at crtc->mode (which is the user mode) dig up the
sync polarity settings from the adjusted_mode when programming
TRANS_DP_CTL on CPT/PPT.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446146763-31821-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>

drm/i915: Don't use intel_pipe_to_cpu_transcoder() when there's a pipe config around

No point in doing the crtc->pipe->crtc->config->cpu_transcoder dance
when we can just do crtc->config->cpu_transcoder.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446146763-31821-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>

drm/i915: remove in_dbg_master check from intel_fbc.c

From our maintainer Daniel Vetter a few days ago:
  "Oh dear this is dead code. kdbg uses the fbcon, which always uses
  untiled, which means fbc will never be enabled. Also we have 0 users
  and 0 test coverage for kdbg on top of i915 (Jesse implemented it
  for fun years back). Imo just remove all this code."

Adding to what Daniel said: for kgdboc's KMS support,
intel_pipe_set_base_atomic() already manually disables FBC, so we
won't do the in_dbg_master() check there. This is essentially a revert
of:

commit c924b934d0cd14a4559611da91f28f59acebe32a
Author: Jason Wessel <jason.wessel@windriver.com>
Date:   Thu Aug 5 09:22:32 2010 -0500
    i915: when kgdb is active display compression should be off

Besides, it is not clear what is the exact problem caused by FBC, and
why other features such as PSR, DRRS, IPS and RPM are not also
checking for in_dbg_master(). IMHO we should either remove the code as
suggested by Daniel or we add some nice comments explaining why is FBC
so special.

v2: Rebase due to new patch order.

Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1446664257-32012-13-git-send-email-paulo.r.zanoni@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: clarify that checking the FB stride for CFB is intentional

Daniel was looking at this code and asked about whether fb->pitches[0]
is correct, then he suggested we should a comment to make sure it is
actually intentional.

For more information on the CFB size calculation, please see the
commit message of:

commit c4ffd40908c30a33291227920e921f6b45b9e8f7
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date:   Thu Oct 1 19:55:57 2015 -0300
    drm/i915: fix CFB size calculation

Requested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446664257-32012-12-git-send-email-paulo.r.zanoni@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: remove too-frequent FBC debug message

If we run igt/kms_frontbuffer_tracking, this message will appear
thousands of times, eating a significant part of our dmesg buffer.
It's part of the expected FBC behavior, so let's just silence it.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446664257-32012-10-git-send-email-paulo.r.zanoni@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: refactor FBC deactivation at init

Make sure we deactivate FBC at intel_fbc_init(), so we can remove the
call from intel_display.c. Currently we only have the "enabled"
software state, but later we'll have both "enabled" and "active", and
we'll add assertions to them, so just calling intel_fbc_disable() from
intel_modeset_init() won't work. It's better to make sure
intel_fbc_init() already puts the hardware in the expected state, so
we can put nice assertions in the other functions.

v2: Keep/improve the comment (Chris).
v3: Improve the commit message a little bit.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446664257-32012-9-git-send-email-paulo.r.zanoni@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: don't disable_fbc() if FBC is already disabled

If FBC is disabled we will still call intel_fbc_invalidate(), and as a
result we may call intel_fbc_deactivate(), which will try to touch
registers.

I'm pretty sure I saw this happen on a runtime suspended device, and
I'm almost sure I was running igt/pm_rpm. It produced the "you touched
registers while the device is suspended" WARNs. But this was some time
ago and I can't remember exactly which conditions were necessary to
reproduce the problem.

v2: Rebase to new series order.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446664257-32012-8-git-send-email-paulo.r.zanoni@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: fix the __intel_fbc_update() comments

Don't try to list in comments the cases where we should enable or
disable FBC: it varies a lot with the hardware generations and the
code should be the documentation. Also notice that there's already a
huge gap between the comments and what's in the code.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446664257-32012-7-git-send-email-paulo.r.zanoni@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: use struct intel_crtc *crtc at __intel_fbc_update()

This change was part of the commit that makes intel_fbc_update()
receive an intel_crtc as argument instead of dev_priv, but since it
was polluting the diff with too many chunks I decided to move it to
its own commit.

It seems that our developers are favoring having this instead of the
old combination drm_crtc *crtc + intel_crtc *intel_crtc, and on the
mentioned commit we'll get rid of the drm_crtc variable, so let's do
an intermediate commit with the rename, so on the next commit we'll
have just struct intel_crtc *crtc.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446664257-32012-6-git-send-email-paulo.r.zanoni@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: extract crtc_is_valid() on the FBC code

We're going to kill intel_fbc_find_crtc(), that's why a big part of
the logic moved from intel_fbc_find_crtc() to crtc_is_valid().

v2:
  - Rebase due to pipe_a_only change.
  - Split the multiline conditional (Chris).

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446664257-32012-5-git-send-email-paulo.r.zanoni@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: remove unnecessary check for crtc->primary->fb

We already check if the CRTC is visible, and it shouldn't be possible
to have a visible CRTC without an FB.

This was noticed by both Chris and Ville on different ocasions.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446664257-32012-4-git-send-email-paulo.r.zanoni@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: extract fbc_on_pipe_a_only()

Make the code easier to read.

Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446664257-32012-3-git-send-email-paulo.r.zanoni@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: rename intel_fbc_nuke to intel_fbc_recompress

Although the term "nuke" is part of the FBC spec, it's not very
intuitive, so let's rename it to make it easier for people that are
not familiar with the spec.

Requested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446664257-32012-2-git-send-email-paulo.r.zanoni@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: remove newline from a no_fbc_reason message

Newlines are not needed and they're not used by the other messages. I
added the newline by mistake.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446664257-32012-14-git-send-email-paulo.r.zanoni@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915/bxt: Force port A DDI to use 4 lanes

The bspec indicates that DDI A using four lanes is the only valid
configuration for Broxton (Broxton doesn't have a DDI E to split these
lanes with); the DDI_A_4_LANES bit of port A's DDI_BUF_CTL should always
be set by the BIOS.  However some BIOS versions seem to only be setting
this bit if eDP is actually lit up at boot time; if the BIOS doesn't
turn on the eDP panel because an external display is plugged in, then
this bit is never properly initialized.  The end result of this is that
we wind up calculating a lower max data rate than we should and may wind
up rejecting the native mode for panels that we should be able to drive.

Let's workaround this BIOS bug by just turning the DDI_A_4_LANES bit on
in our driver's internal state if we recognize that we're running on BXT
where it should have been on anyway.

Cc: Imre Deak <imre.deak@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Tested-by: Bob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446764012-27251-1-git-send-email-matthew.d.roper@intel.com

drm/i915: Print a debug message when exceeding dotclock limit on pre-gen4

Currently there's no trace in dmesg when the gen2/3 dotclock checks
reject the modeset. Add some to avoid further head scratching.

While at it refactor the code a bit to look nicer.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446241178-432-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>

drm/i915: Avoid pointer arithmetic in calculating plane surface offset

VMA offsets are 64 bits. Plane surface offsets are in ggtt and
the hardware register to set this is thus 32 bits. Be explicit
about these and convert carefully to from vma to final size.

This will make sparse happy by not creating 32bit pointers out
of 64bit vma offsets.

Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446204375-29831-1-git-send-email-mika.kuoppala@intel.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

drm/i915: Add dmc firmware load state and version to error state

We have had one case where buggy csr/dmc firmware version influenced
gt side and caused a hang. Add dmc firmware loading state and
version to error state.

v2: - Rebased on top of Damien's patches
    - included fw load state
v3: include dmc info only if platform supports it (Chris)
v4: move *csr to branch scope (Chris)
v5: remove dependency to csr_state

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v4)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446124879-22240-1-git-send-email-mika.kuoppala@intel.com
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

drm/i915: Add csr programming registers to dmc debugfs entry

We check these to determine firmware loading status. Include
them to help to debug causes of firmware loading fails.

v2: Move all CSR specific registers to i915_reg.h (Ville)
v3: Rebase
v4: Rebase (RPM ref)

Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446220487-32691-1-git-send-email-mika.kuoppala@intel.com
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

drm/i915/bxt: Expose DC5 entry count

For bxt CSR firmware exposes a count of dc5 entries. Expose
it through debugs

Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

drm/i915/skl: Expose DC5/DC6 entry counts

The CSR firmware expose two counters, handy to check if we are indeed
entering DC5/DC6.

v2: Rebase
v3: Take RPM ref before reading (Imre)

Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> (v1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446220412-32574-1-git-send-email-mika.kuoppala@intel.com
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

drm/i915/skl: Print the DMC firmware status in debugfs

Create a new debufs file for it, we'll have a few more things to add
there.

v2: Fix checkpatch warning about static const array
v3: use named initializers (Ville)
v4: strip out csr_state as it will be removed in future (Ville, Imre)

Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445950025-5793-3-git-send-email-mika.kuoppala@intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>