Ike Panhc [Fri, 1 Oct 2010 07:39:40 +0000 (15:39 +0800)]
ideapad: use EC command to control camera
Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Ike Panhc [Fri, 1 Oct 2010 07:39:29 +0000 (15:39 +0800)]
ideapad: use return value of _CFG to tell if device exist or not
There are several bits of the return value of _CFG shows if RF/Camera devices
exist or not.
Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Ike Panhc [Fri, 1 Oct 2010 07:39:14 +0000 (15:39 +0800)]
ideapad: make sure we bind on the correct device
By reading from method _CFG to make sure we bind on the correct VPC2004 device.
Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Ike Panhc [Fri, 1 Oct 2010 07:39:05 +0000 (15:39 +0800)]
ideapad: check VPC bit before sync rfkill hw status
Check VPC bit to make sure the HW rfkill is touched.
Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Ike Panhc [Fri, 1 Oct 2010 07:38:46 +0000 (15:38 +0800)]
ideapad: add ACPI helpers
There are two methods under VPC2004 which is used to access VDAT/VCMD of EC
register. Add helpers for read and write these two registers.
And add read_method_int for reading the return value from ACPI methods which
requires no parameter.
Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Keng-Yu Lin [Tue, 28 Sep 2010 03:43:31 +0000 (11:43 +0800)]
dell-laptop: Add debugfs support
Export the status of RF killswitch through debugfs.
The killswitch status is obtained by the SMI to BIOS. Exporting this status
through debugfs can help identify the issue with the misbehaving firmware.
Signed-off-by: Keng-Yu Lin <keng-yu.lin@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Dmitry Torokhov [Thu, 26 Aug 2010 07:15:30 +0000 (00:15 -0700)]
WMI: embed struct device directly into wmi_block
Instead of creating wmi_blocks and then register corresponding devices
on a separate pass do it all in one shot, since lifetime rules for both
objects are the same. This also takes care of leaking devices when
device_create fails for one of them.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Dmitry Torokhov [Thu, 26 Aug 2010 07:15:25 +0000 (00:15 -0700)]
WMI: make use of class device's attributres
Instead of adding modalias attribute manually set it up as class's
device attribute so driver core will create and remove it for us.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Dmitry Torokhov [Thu, 26 Aug 2010 07:15:19 +0000 (00:15 -0700)]
WMI: use pr_err() and friends
This makes source more concise and easier to read.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Dmitry Torokhov [Thu, 26 Aug 2010 07:15:14 +0000 (00:15 -0700)]
WMI: use separate list head for storing wmi blocks
Do not abuse wmi_block structure to hold the head of list
of blocks, use separate list_head for that.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Dmitry Torokhov [Thu, 26 Aug 2010 07:15:09 +0000 (00:15 -0700)]
WMI: simplify handling of returned WMI blocks in parse_wdg()
There is no reason why we allocate memory and copy data into an
intermediate buffer, it is not like we are working with data coming
from userspace.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Dmitry Torokhov [Thu, 26 Aug 2010 07:15:03 +0000 (00:15 -0700)]
WMI: fix potential NULL pointer dereference
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Dmitry Torokhov [Thu, 26 Aug 2010 07:14:58 +0000 (00:14 -0700)]
WMI: do not leak memory in parse_wdg()
If we _WDG returned object that is not buffer we were forgetting
to free memory allocated for that object.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Dmitry Torokhov [Thu, 26 Aug 2010 07:14:53 +0000 (00:14 -0700)]
WMI: fix wmi_gtoa() to actully terminate the string
Courtesy of sparse...
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Dmitry Torokhov [Thu, 26 Aug 2010 07:14:48 +0000 (00:14 -0700)]
WMI: free wmi blocks when parse_wdg() fails
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Dmitry Torokhov [Thu, 26 Aug 2010 07:14:42 +0000 (00:14 -0700)]
WMI: remove EC region handler when _WDG parsing fails
Driver initialization was forgetting to remove EC address space handler
in cases when parse_wdg() method failed.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Dmitry Torokhov [Thu, 26 Aug 2010 07:12:19 +0000 (00:12 -0700)]
asus-laptop: use attribute group to manage attributes
Instead of registering (and removing) every attribute individually
switch to using sysfs attribute group. This makes sure that we
properly unwind and do not try to remove non-existent attributes which
may not be safe to do in the future.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Alan Cox [Mon, 13 Sep 2010 14:55:05 +0000 (15:55 +0100)]
scu_ipc: Fix warning caused by include changes
We need to include the SFI headers. This is fine as the SCU is only
relevant to x86 platforms with SFI.
Fixes the -next warning report.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Andy Shevchenko [Sat, 11 Sep 2010 13:31:02 +0000 (16:31 +0300)]
platform: x86: throw away custom methods
In 2.6.35 the hex_to_bin() was introduced.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: platform-driver-x86@vger.kernel.org
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Randy Dunlap [Sat, 28 Aug 2010 17:10:50 +0000 (10:10 -0700)]
acpi_toshiba: fix kconfig error
Fix kconfig recursive dependency error in ACPI_TOSHIBA:
it uses both select and depends on for BACKLIGHT_CLASS_DEVICE.
drivers/video/backlight/Kconfig:117:error: recursive dependency detected!
drivers/video/backlight/Kconfig:117: symbol BACKLIGHT_CLASS_DEVICE is selected by ACPI_TOSHIBA
drivers/platform/x86/Kconfig:490: symbol ACPI_TOSHIBA depends on LEDS_CLASS
drivers/leds/Kconfig:12: symbol LEDS_CLASS is selected by BACKLIGHT_ADP8860
drivers/video/backlight/Kconfig:285: symbol BACKLIGHT_ADP8860 depends on BACKLIGHT_CLASS_DEVICE
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Pascal de Bruijn [Mon, 30 Aug 2010 07:09:53 +0000 (09:09 +0200)]
Don't show error if Acer WMI is not found
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Dmitry Torokhov [Wed, 25 Aug 2010 14:45:45 +0000 (07:45 -0700)]
asus-laptop: remove no longer used keycode_map field
The driver uses sparse keymap library and does not use this field
anymore.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Corentin Chary [Tue, 24 Aug 2010 07:30:46 +0000 (09:30 +0200)]
asus-laptop: fix gps rfkill
The GPS rfkill crappy code. The ops_data argument wasn't
set, and was totally misused. The fix have been tested
on an Asus R2H.
Cc: stable@kernel.org
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Corentin Chary [Tue, 24 Aug 2010 07:30:45 +0000 (09:30 +0200)]
asus-laptop: Add key found on Asus N61JQ
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Corentin Chary [Tue, 24 Aug 2010 07:30:44 +0000 (09:30 +0200)]
platform-x86: sync eeepc-laptop and asus-laptop
Makes asus-laptop and eeepc-laptop _init/_exit functions
looks exactly the same as they do the same thing.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Dmitry Torokhov [Thu, 5 Aug 2010 05:30:19 +0000 (22:30 -0700)]
toshiba-acpi - switch to using sparse keymap
Instead of implementing its own version of keymap hanlding switch over
to using sparse keymap library.
Also, install notify handler only after we allocated input device,
otherwise we may risk getting event too early and crash. Similarly,
notify handler should be removed before we unregister input device.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Dmitry Torokhov [Thu, 5 Aug 2010 05:30:13 +0000 (22:30 -0700)]
Input: hp-wmi - switch to using sparse keymap library
Instead of implementing its own version of keymap hanlding switch over
to using sparse keymap library.
Also make sure that we install notify handler only after we allocated
input device and that we remove notify handler before unregistering
input device.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Dmitry Torokhov [Thu, 5 Aug 2010 05:30:08 +0000 (22:30 -0700)]
Input: dell-wmi - switch to using sparse keymap library
Instead of implementing its own version of keymap hanlding switch over to
using sparse keymap library.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Dmitry Torokhov [Thu, 5 Aug 2010 05:30:02 +0000 (22:30 -0700)]
panasonic-laptop - switch to using sparse keymap library
nstead of implementing its own version of keymap hanlding switch over to
using sparse keymap library.
Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Dmitry Torokhov [Thu, 5 Aug 2010 05:29:57 +0000 (22:29 -0700)]
topstar-laptop - switch to using sparse keymap library
Instead of implementing its own version of keymap hanlding switch over to
using sparse keymap library.
Acked-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Linus Torvalds [Wed, 20 Oct 2010 20:30:22 +0000 (13:30 -0700)]
Linux 2.6.36
Linus Torvalds [Wed, 20 Oct 2010 20:18:21 +0000 (13:18 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/upstream-linus
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
MIPS: O32 compat/N32: Fix to use compat syscall wrappers for AIO syscalls.
MAINTAINERS: Change list for ioc_serial to linux-serial.
SERIAL: ioc3_serial: Return -ENOMEM on memory allocation failure
MIPS: jz4740: Fix Kbuild Platform file.
MIPS: Repair Kbuild make clean breakage.
Amit Shah [Wed, 20 Oct 2010 03:15:43 +0000 (13:45 +1030)]
virtio: console: Don't block entire guest if host doesn't read data
If the host is slow in reading data or doesn't read data at all,
blocking write calls not only blocked the program that called write()
but the entire guest itself.
To overcome this, let's not block till the host signals it has given
back the virtio ring element we passed it. Instead, send the buffer to
the host and return to userspace. This operation then becomes similar
to how non-blocking writes work, so let's use the existing code for this
path as well.
This code change also ensures blocking write calls do get blocked if
there's not enough room in the virtio ring as well as they don't return
-EAGAIN to userspace.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
CC: stable@kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 20 Oct 2010 20:13:09 +0000 (13:13 -0700)]
Merge git://git./linux/kernel/git/jejb/scsi-rc-fixes-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] bsg: fix incorrect device_status value
[SCSI] Fix VPD inquiry page wrapper
Linus Torvalds [Wed, 20 Oct 2010 16:00:44 +0000 (09:00 -0700)]
Merge branch 'kvm-updates/2.6.36' of git://git./virt/kvm/kvm
* 'kvm-updates/2.6.36' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Fix fs/gs reload oops with invalid ldt
Michel Thebeau [Tue, 28 Sep 2010 18:15:37 +0000 (14:15 -0400)]
MIPS: O32 compat/N32: Fix to use compat syscall wrappers for AIO syscalls.
[Ralf: Michel's original patch only fixed N32; I replicated the same fix
for O32.]
Signed-off-by: Michel Thebeau <michel.thebeau@windriver.com>
Cc: paul.gortmaker@windriver.com
Cc: bruce.ashfield@windriver.com
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Tue, 19 Oct 2010 17:32:41 +0000 (18:32 +0100)]
MAINTAINERS: Change list for ioc_serial to linux-serial.
IOC3 is also being used on SGI MIPS systems but this particular driver is
only being used on IA64 systems so linux-mips made no sense as a list. Pat
also thinks linux-serial@vger.kernel.org is the better list.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Julia Lawall [Fri, 15 Oct 2010 13:00:09 +0000 (15:00 +0200)]
SERIAL: ioc3_serial: Return -ENOMEM on memory allocation failure
In this code, 0 is returned on memory allocation failure, even though other
failures return -ENOMEM or other similar values.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression ret;
expression x,e1,e2,e3;
@@
ret = 0
... when != ret = e1
*x = \(kmalloc\|kcalloc\|kzalloc\)(...)
... when != ret = e2
if (x == NULL) { ... when != ret = e3
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
To: Pat Gefre <pfg@sgi.com>
Cc: kernel-janitors@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1704/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Tue, 19 Oct 2010 01:05:49 +0000 (18:05 -0700)]
MIPS: jz4740: Fix Kbuild Platform file.
The platform specific files should be included via the platform-y
variable.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Patchwork: https://patchwork.linux-mips.org/patch/1719/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Tue, 19 Oct 2010 00:51:26 +0000 (17:51 -0700)]
MIPS: Repair Kbuild make clean breakage.
When running make clean, Kbuild doesn't process the .config file, so nothing
generates a platform-y variable. We can get it to descend into the platform
directories by setting $(obj-).
The dec Platform file was unconditionally setting platform-, obliterating
its previous contents and preventing some directories from being cleaned.
This is change to an append operation '+=' to allow cavium-octeon to be
cleaned.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Patchwork: https://patchwork.linux-mips.org/patch/1718/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Linus Torvalds [Tue, 19 Oct 2010 17:10:20 +0000 (10:10 -0700)]
Merge branch 'drm-fixes' of git://git./linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: avivo cursor workaround applies to evergreen as well
Avi Kivity [Tue, 19 Oct 2010 14:46:55 +0000 (16:46 +0200)]
KVM: Fix fs/gs reload oops with invalid ldt
kvm reloads the host's fs and gs blindly, however the underlying segment
descriptors may be invalid due to the user modifying the ldt after loading
them.
Fix by using the safe accessors (loadsegment() and load_gs_index()) instead
of home grown unsafe versions.
This is CVE-2010-3698.
KVM-Stable-Tag.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Linus Torvalds [Mon, 18 Oct 2010 20:10:36 +0000 (13:10 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/upstream-linus
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
MIPS: Enable ISA_DMA_API config to fix build failure
MIPS: 32-bit: Fix build failure in asm/fcntl.h
MIPS: Remove all generated vmlinuz* files on "make clean"
MIPS: do_sigaltstack() expects userland pointers
MIPS: Fix error values in case of bad_stack
MIPS: Sanitize restart logics
MIPS: secure_computing, syscall audit: syscall number should in r2, not r0.
MIPS: Don't block signals if we'd failed to setup a sigframe
Linus Torvalds [Mon, 18 Oct 2010 20:10:08 +0000 (13:10 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: evdev - fix EVIOCSABS regression
Input: evdev - fix Ooops in EVIOCGABS/EVIOCSABS
Linus Torvalds [Mon, 18 Oct 2010 20:09:26 +0000 (13:09 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: ohci: fix TI TSB82AA2 regression since 2.6.35
Sascha Hauer [Mon, 18 Oct 2010 08:16:26 +0000 (10:16 +0200)]
mxc_nand: do not depend on disabling the irq in the interrupt handler
This patch reverts the driver to enabling/disabling the NFC interrupt
mask rather than enabling/disabling the system interrupt. This cleans
up the driver so that it doesn't rely on interrupts being disabled
within the interrupt handler.
For i.MX21 we keep the current behaviour, that is calling
enable_irq/disable_irq_nosync to enable/disable interrupts. This patch
is based on earlier work by John Ogness.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: John Ogness <john.ogness@linutronix.de>
Tested-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 18 Oct 2010 20:05:10 +0000 (13:05 -0700)]
Merge branch 'for-linus/i2c/2636-rc8' of git://git.fluff.org/bjdooks/linux
* 'for-linus/i2c/2636-rc8' of git://git.fluff.org/bjdooks/linux:
i2c-imx: do not allow interruptions when waiting for I2C to complete
i2c-davinci: Fix TX setup for more SoCs
Linus Torvalds [Mon, 18 Oct 2010 20:04:33 +0000 (13:04 -0700)]
Merge branch 'fixes'
* fixes:
v4l1: fix 32-bit compat microcode loading translation
De-pessimize rds_page_copy_user
Namhyung Kim [Mon, 18 Oct 2010 03:55:21 +0000 (12:55 +0900)]
MIPS: Enable ISA_DMA_API config to fix build failure
Add ISA_DMA_API config item and select it when GENERIC_ISA_DMA enabled.
This fixes build failure on allmodconfig like following:
CC sound/isa/es18xx.o
sound/isa/es18xx.c: In function 'snd_es18xx_playback1_prepare':
sound/isa/es18xx.c:501:9: error: implicit declaration of function 'snd_dma_program'
sound/isa/es18xx.c: In function 'snd_es18xx_playback_pointer':
sound/isa/es18xx.c:818:3: error: implicit declaration of function 'snd_dma_pointer'
make[3]: *** [sound/isa/es18xx.o] Error 1
make[2]: *** [sound/isa/es18xx.o] Error 2
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1717/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Namhyung Kim [Sun, 17 Oct 2010 16:41:39 +0000 (01:41 +0900)]
MIPS: 32-bit: Fix build failure in asm/fcntl.h
CC security/integrity/ima/ima_fs.o
In file included from linux/include/linux/fcntl.h:4:0,
from linux/security/integrity/ima/ima_fs.c:18:
linux/arch/mips/include/asm/fcntl.h:63:2: error: expected specifier-qualifier-list before 'off_t'
make[3]: *** [security/integrity/ima/ima_fs.o] Error 1
make[2]: *** [security/integrity/ima/ima_fs.o] Error 2
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1715/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Wu Zhangjin [Wed, 22 Sep 2010 06:03:57 +0000 (14:03 +0800)]
MIPS: Remove all generated vmlinuz* files on "make clean"
[Ralf: I changed the patch to explicitly list all files to be deleted out
of paranoia.]
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/1590/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Al Viro [Tue, 28 Sep 2010 17:50:57 +0000 (18:50 +0100)]
MIPS: do_sigaltstack() expects userland pointers
o32 compat does the right thing, native and n32 compat do not...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: linux-kernel@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1700/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Al Viro [Tue, 28 Sep 2010 17:50:47 +0000 (18:50 +0100)]
MIPS: Fix error values in case of bad_stack
We want EFAULT, not -<syscall number>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: linux-kernel@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1699/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Al Viro [Tue, 28 Sep 2010 17:50:37 +0000 (18:50 +0100)]
MIPS: Sanitize restart logics
Put the original syscall number into ->regs[0] when we leave syscall
with error. Use it in restart logics. Everything else will have
it 0 since we pass through SAVE_SOME on all the ways in. Note that
in places like bad_stack and inllegal_syscall we leave it 0 - it's not
restartable.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: linux-kernel@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1698/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Al Viro [Tue, 28 Sep 2010 17:50:27 +0000 (18:50 +0100)]
MIPS: secure_computing, syscall audit: syscall number should in r2, not r0.
As it is, audit_syscall_entry() and secure_computing() get the
bogus value (0, in fact)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: linux-kernel@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1697/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Al Viro [Tue, 28 Sep 2010 17:50:17 +0000 (18:50 +0100)]
MIPS: Don't block signals if we'd failed to setup a sigframe
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: linux-kernel@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1696/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Daniel Mack [Mon, 18 Oct 2010 15:43:50 +0000 (08:43 -0700)]
Input: evdev - fix EVIOCSABS regression
448cd16 ("Input: evdev - rearrange ioctl handling") broke EVIOCSABS by
checking for the wrong direction bit.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Tested-by: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Daniel Mack [Mon, 18 Oct 2010 15:43:30 +0000 (08:43 -0700)]
Input: evdev - fix Ooops in EVIOCGABS/EVIOCSABS
This fixes a regression introduced by the dynamic allocation of absinfo
for input devices. We need to bail out early for input devices which
don't have absolute axis.
[ 929.664303] Pid: 2989, comm: input Not tainted 2.6.36-rc8+ #14 MS-7260/MS-7260
[ 929.664318] EIP: 0060:[<
c12bdc01>] EFLAGS:
00010246 CPU: 0
[ 929.664331] EIP is at evdev_ioctl+0x4f8/0x59f
[ 929.664341] EAX:
00000040 EBX:
00000000 ECX:
00000006 EDX:
f45a1efc
[ 929.664355] ESI:
00000000 EDI:
f45a1efc EBP:
f45a1f24 ESP:
f45a1eb8
[ 929.664369] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[ 929.664402]
f470da74 f6a30e78 f462c240 00000018 bfe4a260 00000000 f45b06fc 00000000
[ 929.664429] <0>
000000c4 b769d000 c3544620 f470da74 f45b06fc f45b06fc f45a1f38 c107dd1f
[ 929.664458] <0>
f4710b74 000000c4 00000000 00000000 00000000 0000029d 00000a74 f4710b74
[ 929.664500] [<
c107dd1f>] ? handle_mm_fault+0x2be/0x59a
[ 929.664513] [<
c12bd709>] ? evdev_ioctl+0x0/0x59f
[ 929.664524] [<
c1099d30>] ? do_vfs_ioctl+0x494/0x4d9
[ 929.664538] [<
c10432a1>] ? up_read+0x16/0x29
[ 929.664550] [<
c101c818>] ? do_page_fault+0x2ff/0x32d
[ 929.664564] [<
c108d048>] ? do_sys_open+0xc5/0xcf
[ 929.664575] [<
c1099db6>] ? sys_ioctl+0x41/0x61
[ 929.664587] [<
c1002710>] ? sysenter_do_call+0x12/0x36
[ 929.684570] ---[ end trace
11b83e923bd8f2bb ]---
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Marc Kleine-Budde [Mon, 21 Jun 2010 07:27:05 +0000 (09:27 +0200)]
i2c-imx: do not allow interruptions when waiting for I2C to complete
The i2c_imx_trx_complete() function is using
wait_event_interruptible_timeout() to wait for the I2C controller to
signal that it has completed an I2C bus operation. If the process that
causes the I2C operation receives a signal, the wait will be
interrupted, returning an error. It is better to let the I2C operation
finished before handling the signal (i.e. returning into userspace).
It is safe to use wait_event_timeout() instead, because the timeout
will allow the process to exit if the I2C bus hangs. It's also better
to allow the I2C operation to finish, because unacknowledged I2C
operations can cause the I2C bus to hang.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Jon Povey [Tue, 12 Oct 2010 04:47:05 +0000 (13:47 +0900)]
i2c-davinci: Fix TX setup for more SoCs
This patch is an improvement to
4bba0fd8d1c6d405df666e2573e1a1f917098be0
which got to mainline a little early.
Sudhakar Rajashekhara explains that at least OMAP-L138 requires MDR mode
settings before DXR for correct behaviour, so load MDR first with
STT cleared and later load again with STT set.
Tested on DM355 connected to Techwell TW2836 and Wolfson WM8985
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Alex Deucher [Thu, 14 Oct 2010 21:14:57 +0000 (17:14 -0400)]
drm/radeon/kms: avivo cursor workaround applies to evergreen as well
Fixes cursor corruption in certain cases.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Sun, 17 Oct 2010 16:38:08 +0000 (09:38 -0700)]
Merge branch 'fix/misc' of git://git./linux/kernel/git/tiwai/sound-2.6
* 'fix/misc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: rawmidi: fix oops (use after free) when unloading a driver module
Stefan Richter [Sun, 17 Oct 2010 12:09:12 +0000 (14:09 +0200)]
firewire: ohci: fix TI TSB82AA2 regression since 2.6.35
Revert commit
54672386ccf36ffa21d1de8e75624af83f9b0eeb
"firewire: ohci: fix up configuration of TI chips".
It caused massive slow-down and data corruption with a TSB82AA2 based
StarTech
EC1394B2 ExpressCard and FireWire 800 harddisks.
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/657081
http://thread.gmane.org/gmane.linux.kernel.firewire.user/4013
The fact that some card EEPROMs do not program these enhancements may be
related to TSB81BA3 phy chip errata, if not to bugs of TSB82AA2 itself.
We could re-add these configuration steps, but only conditional on a
whitelist of cards on which these enhancements bring a proven positive
effect.
Reported-and-tested-by: Eric Shattow <lucent@gmail.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org> 2.6.35
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Clemens Ladisch [Fri, 15 Oct 2010 10:06:18 +0000 (12:06 +0200)]
ALSA: rawmidi: fix oops (use after free) when unloading a driver module
When a driver module is unloaded and the last still open file is a raw
MIDI device, the card and its devices will be actually freed in the
snd_card_file_remove() call when that file is closed. Afterwards, rmidi
and rmidi->card point into freed memory, so the module pointer is likely
to be garbage.
(This was introduced by commit
9a1b64caac82aa02cb74587ffc798e6f42c6170a.)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-by: Krzysztof Foltman <wdev@foltman.com>
Cc: 2.6.30-2.6.35 <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kyle McMartin [Sat, 16 Oct 2010 01:17:16 +0000 (21:17 -0400)]
m32r: test __LITTLE_ENDIAN__ instead of __LITTLE_ENDIAN
Fixes build for me... these are what's tested in byteorder.h...
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kyle McMartin [Sat, 16 Oct 2010 01:17:13 +0000 (21:17 -0400)]
m32r: add kernel/.gitignore and ignore vmlinux.lds
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kyle McMartin [Sat, 16 Oct 2010 01:17:09 +0000 (21:17 -0400)]
m32r: get_user takes an lvalue, not a pointer
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Acked-by: Al "my fuckup" Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kyle McMartin [Sat, 16 Oct 2010 01:16:45 +0000 (21:16 -0400)]
m32r: restore _BLOCKABLE
Commit
a7f8388e accidentally removed it... Al explains:
"Sorry, reordering breakage. In the signals tree here I have
static inline void sig_set_blocked(struct sigset_t *set)
...
and it's used all over the place (including quite a few places where
we currently have sigprocmask(SIG_SETMASK, set, NULL), which is what
it's equivalent to). With that done, m32r doesn't use _BLOCKABLE
anywhere, so it got removed. And that chunk got picked when I'd been
reordering the queue to pull the arch-specific fixes in front.
Sorry."
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Paris [Fri, 15 Oct 2010 21:34:14 +0000 (14:34 -0700)]
types.h: define __aligned_u64 and expose to userspace
We currently have a kernel internal type called aligned_u64 which aligns
__u64's on 8 bytes boundaries even on systems which would normally align
them on 4 byte boundaries. This patch creates a new type __aligned_u64
which does the same thing but which is exposed to userspace rather than
being kernel internal.
[akpm: merge early as both the net and audit trees want this]
[akpm@linux-foundation.org: enhance the comment describing the reasons for using aligned_u64. Via Andreas and Andi.]
Based-on-patch-by: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: Eric Paris <eparis@redhat.com>
Cc: Jan Engelhardt <jengelh@medozas.de>
Cc: David Miller <davem@davemloft.net>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
FUJITA Tomonori [Fri, 15 Oct 2010 21:34:13 +0000 (14:34 -0700)]
uml: fix build
Fix a build error introduced by
d6d1b650ae6acce73d55dd024 ("param: simple
locking for sysfs-writable charp parameters").
CC arch/um/kernel/trap.o
arch/um/drivers/hostaudio_kern.c: In function 'hostaudio_open':
arch/um/drivers/hostaudio_kern.c:204: error: '__param_dsp' undeclared (first use in this function)
arch/um/drivers/hostaudio_kern.c:204: error: (Each undeclared identifier is reported only once
arch/um/drivers/hostaudio_kern.c:204: error: for each function it appears in.)
arch/um/drivers/hostaudio_kern.c: In function 'hostmixer_open_mixdev':
arch/um/drivers/hostaudio_kern.c:265: error: '__param_mixer' undeclared (first use in this function)
arch/um/drivers/hostaudio_kern.c:272: error: '__param_dsp' undeclared (first use in this function)
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Tested-by: Toralf Förster <toralf.foerster@gmx.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Dumazet [Fri, 15 Oct 2010 21:34:12 +0000 (14:34 -0700)]
sysctl: min/max bounds are optional
sysctl check complains with a WARN() when proc_doulongvec_minmax() or
proc_doulongvec_ms_jiffies_minmax() are used by a vector of longs (with
more than one element), with no min or max value specified.
This is unexpected, given we had a bug on this min/max handling :)
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: David Miller <davem@davemloft.net>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 15 Oct 2010 18:12:38 +0000 (11:12 -0700)]
v4l1: fix 32-bit compat microcode loading translation
The compat code for the VIDIOCSMICROCODE ioctl is totally buggered.
It's only used by the VIDEO_STRADIS driver, and that one is scheduled to
staging and eventually removed unless somebody steps up to maintain it
(at which point it should use request_firmware() rather than some magic
ioctl). So we'll get rid of it eventually.
But in the meantime, the compatibility ioctl code is broken, and this
tries to get it to at least limp along (even if Mauro suggested just
deleting it entirely, which may be the right thing to do - I don't think
the compatibility translation code has ever worked unless you were very
lucky).
Reported-by: Kees Cook <kees.cook@canonical.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 15 Oct 2010 18:09:28 +0000 (11:09 -0700)]
De-pessimize rds_page_copy_user
Don't try to "optimize" rds_page_copy_user() by using kmap_atomic() and
the unsafe atomic user mode accessor functions. It's actually slower
than the straightforward code on any reasonable modern CPU.
Back when the code was written (although probably not by the time it was
actually merged, though), 32-bit x86 may have been the dominant
architecture. And there kmap_atomic() can be a lot faster than kmap()
(unless you have very good locality, in which case the virtual address
caching by kmap() can overcome all the downsides).
But these days, x86-64 may not be more populous, but it's getting there
(and if you care about performance, it's definitely already there -
you'd have upgraded your CPU's already in the last few years). And on
x86-64, the non-kmap_atomic() version is faster, simply because the code
is simpler and doesn't have the "re-try page fault" case.
People with old hardware are not likely to care about RDS anyway, and
the optimization for the 32-bit case is simply buggy, since it doesn't
verify the user addresses properly.
Reported-by: Dan Rosenberg <drosenberg@vsecurity.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 15 Oct 2010 17:18:36 +0000 (10:18 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/cjb/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: sdio: fix SDIO suspend/resume regression
Ohad Ben-Cohen [Wed, 13 Oct 2010 07:31:56 +0000 (09:31 +0200)]
mmc: sdio: fix SDIO suspend/resume regression
Fix SDIO suspend/resume regression introduced by
4c2ef25fe0b "mmc: fix
all hangs related to mmc/sd card insert/removal during suspend/resume":
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
pm_op(): platform_pm_suspend+0x0/0x5c returns -38
PM: Device pxa2xx-mci.0 failed to suspend: error -38
PM: Some devices failed to suspend
4c2ef25fe0b moved the card removal/insertion mechanism out of MMC's
suspend/resume path and into pm notifiers (mmc_pm_notify), and that
broke SDIO's expectation that mmc_suspend_host() will remove the card,
and squash the error, in case -ENOSYS is returned from the bus suspend
handler (mmc_sdio_suspend() in this case).
mmc_sdio_suspend() is using this whenever at least one of the card's SDIO
function drivers does not have suspend/resume handlers - in that case
it is agreed to force removal of the entire card.
This patch fixes this regression by trivially bringing back that part of
mmc_suspend_host(), which was removed by
4c2ef25fe0b.
Reported-and-tested-by: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: <stable@kernel.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
Linus Torvalds [Fri, 15 Oct 2010 16:50:03 +0000 (09:50 -0700)]
Merge branch 'timers-for-linus-urgent' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'timers-for-linus-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
hrtimer: Preserve timer state in remove_hrtimer()
Linus Torvalds [Fri, 15 Oct 2010 16:49:43 +0000 (09:49 -0700)]
Merge branch 'upstream-fixes' of git://git./linux/kernel/git/jikos/hid
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Add Cando touch screen 15.6-inch product id
HID: Add MULTI_INPUT quirk for turbox/mosart touchscreen
HID: hidraw, fix a NULL pointer dereference in hidraw_write
HID: hidraw, fix a NULL pointer dereference in hidraw_ioctl
Linus Torvalds [Fri, 15 Oct 2010 16:49:16 +0000 (09:49 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
ubd: fix incorrect sector handling during request restart
ps3disk: passing wrong variable to bvec_kunmap_irq()
FUJITA Tomonori [Thu, 16 Sep 2010 15:46:42 +0000 (00:46 +0900)]
[SCSI] bsg: fix incorrect device_status value
bsg incorrectly returns sg's masked_status value for device_status.
[jejb: fix up expression logic]
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Tejun Heo [Fri, 15 Oct 2010 10:56:21 +0000 (12:56 +0200)]
ubd: fix incorrect sector handling during request restart
Commit
f81f2f7c (ubd: drop unnecessary rq->sector manipulation)
dropped request->sector manipulation in preparation for global request
handling cleanup; unfortunately, it incorrectly assumed that the
updated sector wasn't being used.
ubd tries to issue as many requests as possible to io_thread. When
issuing fails due to memory pressure or other reasons, the device is
put on the restart list and issuing stops. On IO completion, devices
on the restart list are scanned and IO issuing is restarted.
ubd issues IOs sg-by-sg and issuing can be stopped in the middle of a
request, so each device on the restart queue needs to remember where
to restart in its current request. ubd needs to keep track of the
issue position itself because,
* blk_rq_pos(req) is now updated by the block layer to keep track of
_completion_ position.
* Multiple io_req's for the current request may be in flight, so it's
difficult to tell where blk_rq_pos(req) currently is.
Add ubd->rq_pos to keep track of the issue position and use it to
correctly restart io_req issue.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Richard Weinberger <richard@nod.at>
Tested-by: Richard Weinberger <richard@nod.at>
Tested-by: Chris Frey <cdfrey@foursquare.net>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Linus Torvalds [Fri, 15 Oct 2010 02:15:28 +0000 (19:15 -0700)]
Export dump_{write,seek} to binary loader modules
If you build aout support as a module, you'll want these exported.
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 14 Oct 2010 23:26:43 +0000 (16:26 -0700)]
Linux 2.6.36-rc8
Linus Torvalds [Thu, 14 Oct 2010 21:32:06 +0000 (14:32 -0700)]
Un-inline the core-dump helper functions
Tony Luck reports that the addition of the access_ok() check in commit
0eead9ab41da ("Don't dump task struct in a.out core-dumps") broke the
ia64 compile due to missing the necessary header file includes.
Rather than add yet another include (<asm/unistd.h>) to make everything
happy, just uninline the silly core dump helper functions and move the
bodies to fs/exec.c where they make a lot more sense.
dump_seek() in particular was too big to be an inline function anyway,
and none of them are in any way performance-critical. And we really
don't need to mess up our include file headers more than they already
are.
Reported-and-tested-by: Tony Luck <tony.luck@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 14 Oct 2010 18:19:44 +0000 (11:19 -0700)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
ehea: Fix a checksum issue on the receive path
net: allow FEC driver to use fixed PHY support
tg3: restore rx_dropped accounting
b44: fix carrier detection on bind
net: clear heap allocations for privileged ethtool actions
NET: wimax, fix use after free
ATM: iphase, remove sleep-inside-atomic
ATM: mpc, fix use after free
ATM: solos-pci, remove use after free
net/fec: carrier off initially to avoid root mount failure
r8169: use device model DMA API
r8169: allocate with GFP_KERNEL flag when able to sleep
Linus Torvalds [Thu, 14 Oct 2010 17:57:40 +0000 (10:57 -0700)]
Don't dump task struct in a.out core-dumps
akiphie points out that a.out core-dumps have that odd task struct
dumping that was never used and was never really a good idea (it goes
back into the mists of history, probably the original core-dumping
code). Just remove it.
Also do the access_ok() check on dump_write(). It probably doesn't
matter (since normal filesystems all seem to do it anyway), but he
points out that it's normally done by the VFS layer, so ...
[ I suspect that we should possibly do "vfs_write()" instead of
calling ->write directly. That also does the whole fsnotify and write
statistics thing, which may or may not be a good idea. ]
And just to be anal, do this all for the x86-64 32-bit a.out emulation
code too, even though it's not enabled (and won't currently even
compile)
Reported-by: akiphie <akiphie@lavabit.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Salman Qazi [Tue, 12 Oct 2010 14:25:19 +0000 (07:25 -0700)]
hrtimer: Preserve timer state in remove_hrtimer()
The race is described as follows:
CPU X CPU Y
remove_hrtimer
// state & QUEUED == 0
timer->state = CALLBACK
unlock timer base
timer->f(n) //very long
hrtimer_start
lock timer base
remove_hrtimer // no effect
hrtimer_enqueue
timer->state = CALLBACK |
QUEUED
unlock timer base
hrtimer_start
lock timer base
remove_hrtimer
mode = INACTIVE
// CALLBACK bit lost!
switch_hrtimer_base
CALLBACK bit not set:
timer->base
changes to a
different CPU.
lock this CPU's timer base
The bug was introduced with commit
ca109491f (hrtimer: removing all ur
callback modes) in 2.6.29
[ tglx: Feed new state via local variable and add a comment. ]
Signed-off-by: Salman Qazi <sqazi@google.com>
Cc: akpm@linux-foundation.org
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <
20101012142351.8485.21823.stgit@dungbeetle.mtv.corp.google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
Linus Torvalds [Wed, 13 Oct 2010 23:51:59 +0000 (16:51 -0700)]
Merge branch 'fixes' of git://git./linux/kernel/git/djbw/async_tx
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
ioat2: fix performance regression
Linus Torvalds [Wed, 13 Oct 2010 23:51:29 +0000 (16:51 -0700)]
Merge branch 'for-2.6.36' of git://linux-nfs.org/~bfields/linux
* 'for-2.6.36' of git://linux-nfs.org/~bfields/linux:
nfsd: fix BUG at fs/nfsd/nfsfh.h:199 on unlink
Linus Torvalds [Wed, 13 Oct 2010 23:50:23 +0000 (16:50 -0700)]
Merge branch 'perf-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ring-buffer: Fix typo of time extends per page
perf, MIPS: Support cross compiling of tools/perf for MIPS
perf: Fix incorrect copy_from_user() usage
Linus Torvalds [Wed, 13 Oct 2010 23:35:33 +0000 (16:35 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: relax ioremap prohibition (
309caa9) for -final and -stable
ARM: 6440/1: ep93xx: DMA: fix channel_disable
cpuimx27: fix i2c bus selection
cpuimx27: fix compile when ULPI is selected
ARM: 6435/1: Fix HWCAP_TLS flag for ARM11MPCore/Cortex-A9
ARM: 6436/1: AT91: Fix power-saving in idle-mode on 926T processors
ARM: fix section mismatch warnings in Versatile Express
ARM: 6412/1: kprobes-decode: add support for MOVW instruction
ARM: 6419/1: mmu: Fix MT_MEMORY and MT_MEMORY_NONCACHED pte flags
ARM: 6416/1: errata: faulty hazard checking in the Store Buffer may lead to data corruption
Linus Torvalds [Wed, 13 Oct 2010 23:35:05 +0000 (16:35 -0700)]
Merge branch 'omap-fixes-for-linus' of git://git./linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
omap: iommu-load cam register before flushing the entry
Linus Torvalds [Wed, 13 Oct 2010 23:34:46 +0000 (16:34 -0700)]
Merge branch 'drm-fixes' of git://git./linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: Silent spurious error message
drm/radeon/kms: fix bad cast/shift in evergreen.c
drm/radeon/kms: make TV/DFP table info less verbose
drm/radeon/kms: leave certain CP int bits enabled
drm/radeon/kms: avoid corner case issue with unmappable vram V2
Linus Torvalds [Wed, 13 Oct 2010 23:34:23 +0000 (16:34 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, numa: For each node, register the memory blocks actually used
x86, AMD, MCE thresholding: Fix the MCi_MISCj iteration order
x86, mce, therm_throt.c: Fix missing curly braces in error handling logic
Dan Williams [Wed, 13 Oct 2010 22:43:10 +0000 (15:43 -0700)]
ioat2: fix performance regression
Commit
0793448 "DMAENGINE: generic channel status v2" changed the interface for
how dma channel progress is retrieved. It inadvertently exported an internal
helper function ioat_tx_status() instead of ioat_dma_tx_status(). The latter
polls the hardware to get the latest completion state, while the helper just
evaluates the current state without touching hardware. The effect is that we
end up waiting for completion timeouts or descriptor allocation errors before
the completion state is updated.
iperf (before fix):
[SUM] 0.0-41.3 sec 364 MBytes 73.9 Mbits/sec
iperf (after fix):
[SUM] 0.0- 4.5 sec 499 MBytes 940 Mbits/sec
This is a regression starting with 2.6.35.
Cc: <stable@kernel.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Reported-by: Richard Scobie <richard@sauce.co.nz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Breno Leitao [Thu, 7 Oct 2010 13:17:33 +0000 (13:17 +0000)]
ehea: Fix a checksum issue on the receive path
Currently we set all skbs with CHECKSUM_UNNECESSARY, even
those whose protocol we don't know. This patch just
add the CHECKSUM_COMPLETE tag for non TCP/UDP packets.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
J. Bruce Fields [Wed, 13 Oct 2010 18:46:17 +0000 (14:46 -0400)]
nfsd: fix BUG at fs/nfsd/nfsfh.h:199 on unlink
As of commit
43a9aa64a2f4330a9cb59aaf5c5636566bce067c "NFSD:
Fill in WCC data for REMOVE, RMDIR, MKNOD, and MKDIR", we sometimes call
fh_unlock on a filehandle that isn't fully initialized.
We should fix up the callers, but as a quick fix it is also sufficient
just to remove this assertion.
Reported-by: Marius Tolzmann <tolzmann@molgen.mpg.de>
Cc: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Greg Ungerer [Mon, 11 Oct 2010 21:03:05 +0000 (21:03 +0000)]
net: allow FEC driver to use fixed PHY support
At least one board using the FEC driver does not have a conventional
PHY attached to it, it is directly connected to a somewhat simple
ethernet switch (the board is the SnapGear/LITE, and the attached
4-port ethernet switch is a RealTek RTL8305). This switch does not
present the usual register interface of a PHY, it presents nothing.
So a PHY scan will find nothing - it finds ID's of 0 for each PHY
on the attached MII bus.
After the FEC driver was changed to use phylib for supporting PHYs
it no longer works on this particular board/switch setup.
Add code support to use a fixed phy if no PHY is found on the MII bus.
This is based on the way the cpmac.c driver solved this same problem.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
François Jaouen [Wed, 13 Oct 2010 08:47:32 +0000 (10:47 +0200)]
HID: Add Cando touch screen 15.6-inch product id
This add the product id of the touch screen found on ACER Aspire 5738PZ. Works
with hid-cando driver.
Signed-off-by: Francois Jaouen<francois.jaouen@laposte.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Russell King [Tue, 12 Oct 2010 23:15:25 +0000 (00:15 +0100)]
ARM: relax ioremap prohibition (
309caa9) for -final and -stable
... but produce a big warning about the problem as encouragement
for people to fix their drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 12 Oct 2010 21:43:26 +0000 (22:43 +0100)]
Merge branch 'for-rmk' of git://git.pengutronix.de/git/imx/linux-2.6
projects / GitHub / mt8127 / android_kernel_alcatel_ttab.git / log