Vignesh Raghavendra [Thu, 19 Mar 2020 10:32:29 +0000 (16:02 +0530)]
serial: 8250_port: Don't service RX FIFO if throttled
[ Upstream commit
f19c3f6c8109b8bab000afd35580929958e087a9 ]
When port's throttle callback is called, it should stop pushing any more
data into TTY buffer to avoid buffer overflow. This means driver has to
stop HW from receiving more data and assert the HW flow control. For
UARTs with auto HW flow control (such as 8250_omap) manual assertion of
flow control line is not possible and only way is to allow RX FIFO to
fill up, thus trigger auto HW flow control logic.
Therefore make sure that 8250 generic IRQ handler does not drain data
when port is stopped (i.e UART_LSR_DR is unset in read_status_mask). Not
servicing, RX FIFO would trigger auto HW flow control when FIFO
occupancy reaches preset threshold, thus halting RX.
Since, error conditions in UART_LSR register are cleared just by reading
the register, data has to be drained in case there are FIFO errors, else
error information will lost.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319103230.16867-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nathan Chancellor [Thu, 20 Feb 2020 05:10:12 +0000 (22:10 -0700)]
tracing: Use address-of operator on section symbols
[ Upstream commit
bf2cbe044da275021b2de5917240411a19e5c50d ]
Clang warns:
../kernel/trace/trace.c:9335:33: warning: array comparison always
evaluates to true [-Wtautological-compare]
if (__stop___trace_bprintk_fmt != __start___trace_bprintk_fmt)
^
1 warning generated.
These are not true arrays, they are linker defined symbols, which are
just addresses. Using the address of operator silences the warning and
does not change the runtime result of the check (tested with some print
statements compiled in with clang + ld.lld and gcc + ld.bfd in QEMU).
Link: http://lkml.kernel.org/r/20200220051011.26113-1-natechancellor@gmail.com
Link: https://github.com/ClangBuiltLinux/linux/issues/893
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Stefan Berger [Thu, 12 Mar 2020 15:53:31 +0000 (11:53 -0400)]
tpm: ibmvtpm: Wait for buffer to be set before proceeding
[ Upstream commit
d8d74ea3c00214aee1e1826ca18e77944812b9b4 ]
Synchronize with the results from the CRQs before continuing with
the initialization. This avoids trying to send TPM commands while
the rtce buffer has not been allocated, yet.
This patch fixes an existing race condition that may occurr if the
hypervisor does not quickly respond to the VTPM_GET_RTCE_BUFFER_SIZE
request sent during initialization and therefore the ibmvtpm->rtce_buf
has not been allocated at the time the first TPM command is sent.
Fixes:
132f76294744 ("drivers/char/tpm: Add new device driver to support IBM vTPM")
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Acked-by: Nayna Jain <nayna@linux.ibm.com>
Tested-by: Nayna Jain <nayna@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Darrick J. Wong [Wed, 11 Mar 2020 17:37:55 +0000 (10:37 -0700)]
xfs: don't ever return a stale pointer from __xfs_dir3_free_read
[ Upstream commit
1cb5deb5bc095c070c09a4540c45f9c9ba24be43 ]
If we decide that a directory free block is corrupt, we must take care
not to leak a buffer pointer to the caller. After xfs_trans_brelse
returns, the buffer can be freed or reused, which means that we have to
set *bpp back to NULL.
Callers are supposed to notice the nonzero return value and not use the
buffer pointer, but we should code more defensively, even if all current
callers handle this situation correctly.
Fixes:
de14c5f541e7 ("xfs: verify free block header fields")
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Colin Ian King [Mon, 10 Feb 2020 14:26:46 +0000 (15:26 +0100)]
media: tda10071: fix unsigned sign extension overflow
[ Upstream commit
a7463e2dc698075132de9905b89f495df888bb79 ]
The shifting of buf[3] by 24 bits to the left will be promoted to
a 32 bit signed int and then sign-extended to an unsigned long. In
the unlikely event that the the top bit of buf[3] is set then all
then all the upper bits end up as also being set because of
the sign-extension and this affect the ev->post_bit_error sum.
Fix this by using the temporary u32 variable bit_error to avoid
the sign-extension promotion. This also removes the need to do the
computation twice.
Addresses-Coverity: ("Unintended sign extension")
Fixes:
267897a4708f ("[media] tda10071: implement DVBv5 statistics")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Howard Chung [Thu, 12 Mar 2020 04:35:27 +0000 (12:35 +0800)]
Bluetooth: L2CAP: handle l2cap config request during open state
[ Upstream commit
96298f640104e4cd9a913a6e50b0b981829b94ff ]
According to Core Spec Version 5.2 | Vol 3, Part A 6.1.5,
the incoming L2CAP_ConfigReq should be handled during
OPEN state.
The section below shows the btmon trace when running
L2CAP/COS/CFD/BV-12-C before and after this change.
=== Before ===
...
> ACL Data RX: Handle 256 flags 0x02 dlen 12 #22
L2CAP: Connection Request (0x02) ident 2 len 4
PSM: 1 (0x0001)
Source CID: 65
< ACL Data TX: Handle 256 flags 0x00 dlen 16 #23
L2CAP: Connection Response (0x03) ident 2 len 8
Destination CID: 64
Source CID: 65
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
< ACL Data TX: Handle 256 flags 0x00 dlen 12 #24
L2CAP: Configure Request (0x04) ident 2 len 4
Destination CID: 65
Flags: 0x0000
> HCI Event: Number of Completed Packets (0x13) plen 5 #25
Num handles: 1
Handle: 256
Count: 1
> HCI Event: Number of Completed Packets (0x13) plen 5 #26
Num handles: 1
Handle: 256
Count: 1
> ACL Data RX: Handle 256 flags 0x02 dlen 16 #27
L2CAP: Configure Request (0x04) ident 3 len 8
Destination CID: 64
Flags: 0x0000
Option: Unknown (0x10) [hint]
01 00 ..
< ACL Data TX: Handle 256 flags 0x00 dlen 18 #28
L2CAP: Configure Response (0x05) ident 3 len 10
Source CID: 65
Flags: 0x0000
Result: Success (0x0000)
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 672
> HCI Event: Number of Completed Packets (0x13) plen 5 #29
Num handles: 1
Handle: 256
Count: 1
> ACL Data RX: Handle 256 flags 0x02 dlen 14 #30
L2CAP: Configure Response (0x05) ident 2 len 6
Source CID: 64
Flags: 0x0000
Result: Success (0x0000)
> ACL Data RX: Handle 256 flags 0x02 dlen 20 #31
L2CAP: Configure Request (0x04) ident 3 len 12
Destination CID: 64
Flags: 0x0000
Option: Unknown (0x10) [hint]
01 00 91 02 11 11 ......
< ACL Data TX: Handle 256 flags 0x00 dlen 14 #32
L2CAP: Command Reject (0x01) ident 3 len 6
Reason: Invalid CID in request (0x0002)
Destination CID: 64
Source CID: 65
> HCI Event: Number of Completed Packets (0x13) plen 5 #33
Num handles: 1
Handle: 256
Count: 1
...
=== After ===
...
> ACL Data RX: Handle 256 flags 0x02 dlen 12 #22
L2CAP: Connection Request (0x02) ident 2 len 4
PSM: 1 (0x0001)
Source CID: 65
< ACL Data TX: Handle 256 flags 0x00 dlen 16 #23
L2CAP: Connection Response (0x03) ident 2 len 8
Destination CID: 64
Source CID: 65
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
< ACL Data TX: Handle 256 flags 0x00 dlen 12 #24
L2CAP: Configure Request (0x04) ident 2 len 4
Destination CID: 65
Flags: 0x0000
> HCI Event: Number of Completed Packets (0x13) plen 5 #25
Num handles: 1
Handle: 256
Count: 1
> HCI Event: Number of Completed Packets (0x13) plen 5 #26
Num handles: 1
Handle: 256
Count: 1
> ACL Data RX: Handle 256 flags 0x02 dlen 16 #27
L2CAP: Configure Request (0x04) ident 3 len 8
Destination CID: 64
Flags: 0x0000
Option: Unknown (0x10) [hint]
01 00 ..
< ACL Data TX: Handle 256 flags 0x00 dlen 18 #28
L2CAP: Configure Response (0x05) ident 3 len 10
Source CID: 65
Flags: 0x0000
Result: Success (0x0000)
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 672
> HCI Event: Number of Completed Packets (0x13) plen 5 #29
Num handles: 1
Handle: 256
Count: 1
> ACL Data RX: Handle 256 flags 0x02 dlen 14 #30
L2CAP: Configure Response (0x05) ident 2 len 6
Source CID: 64
Flags: 0x0000
Result: Success (0x0000)
> ACL Data RX: Handle 256 flags 0x02 dlen 20 #31
L2CAP: Configure Request (0x04) ident 3 len 12
Destination CID: 64
Flags: 0x0000
Option: Unknown (0x10) [hint]
01 00 91 02 11 11 .....
< ACL Data TX: Handle 256 flags 0x00 dlen 18 #32
L2CAP: Configure Response (0x05) ident 3 len 10
Source CID: 65
Flags: 0x0000
Result: Success (0x0000)
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 672
< ACL Data TX: Handle 256 flags 0x00 dlen 12 #33
L2CAP: Configure Request (0x04) ident 3 len 4
Destination CID: 65
Flags: 0x0000
> HCI Event: Number of Completed Packets (0x13) plen 5 #34
Num handles: 1
Handle: 256
Count: 1
> HCI Event: Number of Completed Packets (0x13) plen 5 #35
Num handles: 1
Handle: 256
Count: 1
...
Signed-off-by: Howard Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
John Clements [Thu, 5 Mar 2020 09:48:56 +0000 (17:48 +0800)]
drm/amdgpu: increase atombios cmd timeout
[ Upstream commit
1b3460a8b19688ad3033b75237d40fa580a5a953 ]
mitigates race condition on BACO reset between GPU bootcode and driver reload
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Wen Yang [Mon, 20 Jan 2020 10:05:23 +0000 (18:05 +0800)]
timekeeping: Prevent 32bit truncation in scale64_check_overflow()
[ Upstream commit
4cbbc3a0eeed675449b1a4d080008927121f3da3 ]
While unlikely the divisor in scale64_check_overflow() could be >= 32bit in
scale64_check_overflow(). do_div() truncates the divisor to 32bit at least
on 32bit platforms.
Use div64_u64() instead to avoid the truncation to 32-bit.
[ tglx: Massaged changelog ]
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20200120100523.45656-1-wenyang@linux.alibaba.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Alain Michaud [Tue, 3 Mar 2020 15:55:34 +0000 (15:55 +0000)]
Bluetooth: guard against controllers sending zero'd events
[ Upstream commit
08bb4da90150e2a225f35e0f642cdc463958d696 ]
Some controllers have been observed to send zero'd events under some
conditions. This change guards against this condition as well as adding
a trace to facilitate diagnosability of this condition.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Takashi Iwai [Thu, 6 Feb 2020 15:45:27 +0000 (16:45 +0100)]
media: go7007: Fix URB type for interrupt handling
[ Upstream commit
a3ea410cac41b19a5490aad7fe6d9a9a772e646e ]
Josef reported that his old-and-good Plextor ConvertX M402U video
converter spews lots of WARNINGs on the recent kernels, and it turned
out that the device uses a bulk endpoint for interrupt handling just
like 2250 board.
For fixing it, generalize the check with the proper verification of
the endpoint instead of hard-coded board type check.
Fixes:
7e5219d18e93 ("[media] go7007: Fix 2250 urb type")
Reported-and-tested-by: Josef Möllers <josef.moellers@suse.com>
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1162583
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206427
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dmitry Osipenko [Sun, 9 Feb 2020 16:33:41 +0000 (19:33 +0300)]
dmaengine: tegra-apb: Prevent race conditions on channel's freeing
[ Upstream commit
8e84172e372bdca20c305d92d51d33640d2da431 ]
It's incorrect to check the channel's "busy" state without taking a lock.
That shouldn't cause any real troubles, nevertheless it's always better
not to have any race conditions in the code.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20200209163356.6439-5-digetx@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Thomas Gleixner [Mon, 24 Feb 2020 14:01:39 +0000 (15:01 +0100)]
bpf: Remove recursion prevention from rcu free callback
[ Upstream commit
8a37963c7ac9ecb7f86f8ebda020e3f8d6d7b8a0 ]
If an element is freed via RCU then recursion into BPF instrumentation
functions is not a concern. The element is already detached from the map
and the RCU callback does not hold any locks on which a kprobe, perf event
or tracepoint attached BPF program could deadlock.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200224145643.259118710@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dave Hansen [Wed, 22 Jan 2020 16:53:46 +0000 (08:53 -0800)]
x86/pkeys: Add check for pkey "overflow"
[ Upstream commit
16171bffc829272d5e6014bad48f680cb50943d9 ]
Alex Shi reported the pkey macros above arch_set_user_pkey_access()
to be unused. They are unused, and even refer to a nonexistent
CONFIG option.
But, they might have served a good use, which was to ensure that
the code does not try to set values that would not fit in the
PKRU register. As it stands, a too-large 'pkey' value would
be likely to silently overflow the u32 new_pkru_bits.
Add a check to look for overflows. Also add a comment to remind
any future developer to closely examine the types used to store
pkey values if arch_max_pkey() ever changes.
This boots and passes the x86 pkey selftests.
Reported-by: Alex Shi <alex.shi@linux.alibaba.com>
Signed-off-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200122165346.AD4DA150@viggo.jf.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Paolo Bonzini [Thu, 13 Feb 2020 17:24:48 +0000 (18:24 +0100)]
KVM: x86: fix incorrect comparison in trace event
[ Upstream commit
147f1a1fe5d7e6b01b8df4d0cbd6f9eaf6b6c73b ]
The "u" field in the event has three states, -1/0/1. Using u8 however means that
comparison with -1 will always fail, so change to signed char.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Bart Van Assche [Mon, 17 Feb 2020 20:57:14 +0000 (12:57 -0800)]
RDMA/rxe: Fix configuration of atomic queue pair attributes
[ Upstream commit
fb3063d31995cc4cf1d47a406bb61d6fb1b1d58d ]
From the comment above the definition of the roundup_pow_of_two() macro:
The result is undefined when n == 0.
Hence only pass positive values to roundup_pow_of_two(). This patch fixes
the following UBSAN complaint:
UBSAN: Undefined behaviour in ./include/linux/log2.h:57:13
shift exponent 64 is too large for 64-bit type 'long unsigned int'
Call Trace:
dump_stack+0xa5/0xe6
ubsan_epilogue+0x9/0x26
__ubsan_handle_shift_out_of_bounds.cold+0x4c/0xf9
rxe_qp_from_attr.cold+0x37/0x5d [rdma_rxe]
rxe_modify_qp+0x59/0x70 [rdma_rxe]
_ib_modify_qp+0x5aa/0x7c0 [ib_core]
ib_modify_qp+0x3b/0x50 [ib_core]
cma_modify_qp_rtr+0x234/0x260 [rdma_cm]
__rdma_accept+0x1a7/0x650 [rdma_cm]
nvmet_rdma_cm_handler+0x1286/0x14cd [nvmet_rdma]
cma_cm_event_handler+0x6b/0x330 [rdma_cm]
cma_ib_req_handler+0xe60/0x22d0 [rdma_cm]
cm_process_work+0x30/0x140 [ib_cm]
cm_req_handler+0x11f4/0x1cd0 [ib_cm]
cm_work_handler+0xb8/0x344e [ib_cm]
process_one_work+0x569/0xb60
worker_thread+0x7a/0x5d0
kthread+0x1e6/0x210
ret_from_fork+0x24/0x30
Link: https://lore.kernel.org/r/20200217205714.26937-1-bvanassche@acm.org
Fixes:
8700e3e7c485 ("Soft RoCE driver")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Wen Yang [Mon, 8 Apr 2019 02:58:32 +0000 (10:58 +0800)]
drm/omap: fix possible object reference leak
[ Upstream commit
47340e46f34a3b1d80e40b43ae3d7a8da34a3541 ]
The call to of_find_matching_node returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
drivers/gpu/drm/omapdrm/dss/omapdss-boot-init.c:212:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 209, but without a corresponding object release within this function.
drivers/gpu/drm/omapdrm/dss/omapdss-boot-init.c:237:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 209, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Sebastian Reichel <sebastian.reichel@collabora.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Cc: Markus Elfring <Markus.Elfring@web.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1554692313-28882-2-git-send-email-wen.yang99@zte.com.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
James Smart [Tue, 28 Jan 2020 00:23:07 +0000 (16:23 -0800)]
scsi: lpfc: Fix coverity errors in fmdi attribute handling
[ Upstream commit
4cb9e1ddaa145be9ed67b6a7de98ca705a43f998 ]
Coverity reported a memory corruption error for the fdmi attributes
routines:
CID 15768 [Memory Corruption] Out-of-bounds access on FDMI
Sloppy coding of the fmdi structures. In both the lpfc_fdmi_attr_def and
lpfc_fdmi_reg_port_list structures, a field was placed at the start of
payload that may have variable content. The field was given an arbitrary
type (uint32_t). The code then uses the field name to derive an address,
which it used in things such as memset and memcpy. The memset sizes or
memcpy lengths were larger than the arbitrary type, thus coverity reported
an error.
Fix by replacing the arbitrary fields with the real field structures
describing the payload.
Link: https://lore.kernel.org/r/20200128002312.16346-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
James Smart [Tue, 28 Jan 2020 00:23:01 +0000 (16:23 -0800)]
scsi: lpfc: Fix RQ buffer leakage when no IOCBs available
[ Upstream commit
39c4f1a965a9244c3ba60695e8ff8da065ec6ac4 ]
The driver is occasionally seeing the following SLI Port error, requiring
reset and reinit:
Port Status Event: ... error 1=0x52004a01, error 2=0x218
The failure means an RQ timeout. That is, the adapter had received
asynchronous receive frames, ran out of buffer slots to place the frames,
and the driver did not replenish the buffer slots before a timeout
occurred. The driver should not be so slow in replenishing buffers that a
timeout can occur.
When the driver received all the frames of a sequence, it allocates an IOCB
to put the frames in. In a situation where there was no IOCB available for
the frame of a sequence, the RQ buffer corresponding to the first frame of
the sequence was not returned to the FW. Eventually, with enough traffic
encountering the situation, the timeout occurred.
Fix by releasing the buffer back to firmware whenever there is no IOCB for
the first frame.
[mkp: typo]
Link: https://lore.kernel.org/r/20200128002312.16346-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vasily Averin [Sat, 1 Feb 2020 07:47:47 +0000 (10:47 +0300)]
selinux: sel_avc_get_stat_idx should increase position index
[ Upstream commit
8d269a8e2a8f0bca89022f4ec98de460acb90365 ]
If seq_file .next function does not change position index,
read after some lseek can generate unexpected output.
$ dd if=/sys/fs/selinux/avc/cache_stats # usual output
lookups hits misses allocations reclaims frees
817223 810034 7189 7189 6992 7037
1934894 1926896 7998 7998 7632 7683
1322812 1317176 5636 5636 5456 5507
1560571 1551548 9023 9023 9056 9115
0+1 records in
0+1 records out
189 bytes copied, 5,1564e-05 s, 3,7 MB/s
$# read after lseek to midle of last line
$ dd if=/sys/fs/selinux/avc/cache_stats bs=180 skip=1
dd: /sys/fs/selinux/avc/cache_stats: cannot skip to specified offset
056 9115 <<<< end of last line
1560571 1551548 9023 9023 9056 9115 <<< whole last line once again
0+1 records in
0+1 records out
45 bytes copied, 8,7221e-05 s, 516 kB/s
$# read after lseek beyond end of of file
$ dd if=/sys/fs/selinux/avc/cache_stats bs=1000 skip=1
dd: /sys/fs/selinux/avc/cache_stats: cannot skip to specified offset
1560571 1551548 9023 9023 9056 9115 <<<< generates whole last line
0+1 records in
0+1 records out
36 bytes copied, 9,0934e-05 s, 396 kB/s
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Steve Grubb [Fri, 24 Jan 2020 22:29:16 +0000 (17:29 -0500)]
audit: CONFIG_CHANGE don't log internal bookkeeping as an event
[ Upstream commit
70b3eeed49e8190d97139806f6fbaf8964306cdb ]
Common Criteria calls out for any action that modifies the audit trail to
be recorded. That usually is interpreted to mean insertion or removal of
rules. It is not required to log modification of the inode information
since the watch is still in effect. Additionally, if the rule is a never
rule and the underlying file is one they do not want events for, they
get an event for this bookkeeping update against their wishes.
Since no device/inode info is logged at insertion and no device/inode
information is logged on update, there is nothing meaningful being
communicated to the admin by the CONFIG_CHANGE updated_rules event. One
can assume that the rule was not "modified" because it is still watching
the intended target. If the device or inode cannot be resolved, then
audit_panic is called which is sufficient.
The correct resolution is to drop logging config_update events since
the watch is still in effect but just on another unknown inode.
Signed-off-by: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Qian Cai [Tue, 4 Feb 2020 18:40:29 +0000 (13:40 -0500)]
skbuff: fix a data race in skb_queue_len()
[ Upstream commit
86b18aaa2b5b5bb48e609cd591b3d2d0fdbe0442 ]
sk_buff.qlen can be accessed concurrently as noticed by KCSAN,
BUG: KCSAN: data-race in __skb_try_recv_from_queue / unix_dgram_sendmsg
read to 0xffff8a1b1d8a81c0 of 4 bytes by task 5371 on cpu 96:
unix_dgram_sendmsg+0x9a9/0xb70 include/linux/skbuff.h:1821
net/unix/af_unix.c:1761
____sys_sendmsg+0x33e/0x370
___sys_sendmsg+0xa6/0xf0
__sys_sendmsg+0x69/0xf0
__x64_sys_sendmsg+0x51/0x70
do_syscall_64+0x91/0xb47
entry_SYSCALL_64_after_hwframe+0x49/0xbe
write to 0xffff8a1b1d8a81c0 of 4 bytes by task 1 on cpu 99:
__skb_try_recv_from_queue+0x327/0x410 include/linux/skbuff.h:2029
__skb_try_recv_datagram+0xbe/0x220
unix_dgram_recvmsg+0xee/0x850
____sys_recvmsg+0x1fb/0x210
___sys_recvmsg+0xa2/0xf0
__sys_recvmsg+0x66/0xf0
__x64_sys_recvmsg+0x51/0x70
do_syscall_64+0x91/0xb47
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Since only the read is operating as lockless, it could introduce a logic
bug in unix_recvq_full() due to the load tearing. Fix it by adding
a lockless variant of skb_queue_len() and unix_recvq_full() where
READ_ONCE() is on the read while WRITE_ONCE() is on the write similar to
the commit
d7d16a89350a ("net: add skb_queue_empty_lockless()").
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mohan Kumar [Thu, 6 Feb 2020 10:10:53 +0000 (15:40 +0530)]
ALSA: hda: Clear RIRB status before reading WP
[ Upstream commit
6d011d5057ff88ee556c000ac6fe0be23bdfcd72 ]
RIRB interrupt status getting cleared after the write pointer is read
causes a race condition, where last response(s) into RIRB may remain
unserviced by IRQ, eventually causing azx_rirb_get_response to fall
back to polling mode. Clearing the RIRB interrupt status ahead of
write pointer access ensures that this condition is avoided.
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Signed-off-by: Viswanath L <viswanathl@nvidia.com>
Link: https://lore.kernel.org/r/1580983853-351-1-git-send-email-viswanathl@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zhuang Yanying [Sat, 12 Oct 2019 03:37:31 +0000 (11:37 +0800)]
KVM: fix overflow of zero page refcount with ksm running
[ Upstream commit
7df003c85218b5f5b10a7f6418208f31e813f38f ]
We are testing Virtual Machine with KSM on v5.4-rc2 kernel,
and found the zero_page refcount overflow.
The cause of refcount overflow is increased in try_async_pf
(get_user_page) without being decreased in mmu_set_spte()
while handling ept violation.
In kvm_release_pfn_clean(), only unreserved page will call
put_page. However, zero page is reserved.
So, as well as creating and destroy vm, the refcount of
zero page will continue to increase until it overflows.
step1:
echo 10000 > /sys/kernel/pages_to_scan/pages_to_scan
echo 1 > /sys/kernel/pages_to_scan/run
echo 1 > /sys/kernel/pages_to_scan/use_zero_pages
step2:
just create several normal qemu kvm vms.
And destroy it after 10s.
Repeat this action all the time.
After a long period of time, all domains hang because
of the refcount of zero page overflow.
Qemu print error log as follow:
…
error: kvm run failed Bad address
EAX=
00006cdc EBX=
00000008 ECX=
80202001 EDX=
078bfbfd
ESI=
ffffffff EDI=
00000000 EBP=
00000008 ESP=
00006cc4
EIP=
000efd75 EFL=
00010002 [-------] CPL=0 II=0 A20=1 SMM=0 HLT=0
ES =0010
00000000 ffffffff 00c09300 DPL=0 DS [-WA]
CS =0008
00000000 ffffffff 00c09b00 DPL=0 CS32 [-RA]
SS =0010
00000000 ffffffff 00c09300 DPL=0 DS [-WA]
DS =0010
00000000 ffffffff 00c09300 DPL=0 DS [-WA]
FS =0010
00000000 ffffffff 00c09300 DPL=0 DS [-WA]
GS =0010
00000000 ffffffff 00c09300 DPL=0 DS [-WA]
LDT=0000
00000000 0000ffff 00008200 DPL=0 LDT
TR =0000
00000000 0000ffff 00008b00 DPL=0 TSS32-busy
GDT=
000f7070 00000037
IDT=
000f70ae 00000000
CR0=
00000011 CR2=
00000000 CR3=
00000000 CR4=
00000000
DR0=
0000000000000000 DR1=
0000000000000000 DR2=
0000000000000000 DR3=
0000000000000000
DR6=
00000000ffff0ff0 DR7=
0000000000000400
EFER=
0000000000000000
Code=00 01 00 00 00 e9 e8 00 00 00 c7 05 4c 55 0f 00 01 00 00 00 <8b> 35 00 00 01 00 8b 3d 04 00 01 00 b8 d8 d3 00 00 c1 e0 08 0c ea a3 00 00 01 00 c7 05 04
…
Meanwhile, a kernel warning is departed.
[40914.836375] WARNING: CPU: 3 PID: 82067 at ./include/linux/mm.h:987 try_get_page+0x1f/0x30
[40914.836412] CPU: 3 PID: 82067 Comm: CPU 0/KVM Kdump: loaded Tainted: G OE 5.2.0-rc2 #5
[40914.836415] RIP: 0010:try_get_page+0x1f/0x30
[40914.836417] Code: 40 00 c3 0f 1f 84 00 00 00 00 00 48 8b 47 08 a8 01 75 11 8b 47 34 85 c0 7e 10 f0 ff 47 34 b8 01 00 00 00 c3 48 8d 78 ff eb e9 <0f> 0b 31 c0 c3 66 90 66 2e 0f 1f 84 00 0
0 00 00 00 48 8b 47 08 a8
[40914.836418] RSP: 0018:
ffffb4144e523988 EFLAGS:
00010286
[40914.836419] RAX:
0000000080000000 RBX:
0000000000000326 RCX:
0000000000000000
[40914.836420] RDX:
0000000000000000 RSI:
00004ffdeba10000 RDI:
ffffdf07093f6440
[40914.836421] RBP:
ffffdf07093f6440 R08:
800000424fd91225 R09:
0000000000000000
[40914.836421] R10:
ffff9eb41bfeebb8 R11:
0000000000000000 R12:
ffffdf06bbd1e8a8
[40914.836422] R13:
0000000000000080 R14:
800000424fd91225 R15:
ffffdf07093f6440
[40914.836423] FS:
00007fb60ffff700(0000) GS:
ffff9eb4802c0000(0000) knlGS:
0000000000000000
[40914.836425] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[40914.836426] CR2:
0000000000000000 CR3:
0000002f220e6002 CR4:
00000000003626e0
[40914.836427] DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
[40914.836427] DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
[40914.836428] Call Trace:
[40914.836433] follow_page_pte+0x302/0x47b
[40914.836437] __get_user_pages+0xf1/0x7d0
[40914.836441] ? irq_work_queue+0x9/0x70
[40914.836443] get_user_pages_unlocked+0x13f/0x1e0
[40914.836469] __gfn_to_pfn_memslot+0x10e/0x400 [kvm]
[40914.836486] try_async_pf+0x87/0x240 [kvm]
[40914.836503] tdp_page_fault+0x139/0x270 [kvm]
[40914.836523] kvm_mmu_page_fault+0x76/0x5e0 [kvm]
[40914.836588] vcpu_enter_guest+0xb45/0x1570 [kvm]
[40914.836632] kvm_arch_vcpu_ioctl_run+0x35d/0x580 [kvm]
[40914.836645] kvm_vcpu_ioctl+0x26e/0x5d0 [kvm]
[40914.836650] do_vfs_ioctl+0xa9/0x620
[40914.836653] ksys_ioctl+0x60/0x90
[40914.836654] __x64_sys_ioctl+0x16/0x20
[40914.836658] do_syscall_64+0x5b/0x180
[40914.836664] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[40914.836666] RIP: 0033:0x7fb61cb6bfc7
Signed-off-by: LinFeng <linfeng23@huawei.com>
Signed-off-by: Zhuang Yanying <ann.zhuangyanying@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hillf Danton [Wed, 5 Feb 2020 02:31:59 +0000 (10:31 +0800)]
Bluetooth: prefetch channel before killing sock
[ Upstream commit
2a154903cec20fb64ff4d7d617ca53c16f8fd53a ]
Prefetch channel before killing sock in order to fix UAF like
BUG: KASAN: use-after-free in l2cap_sock_release+0x24c/0x290 net/bluetooth/l2cap_sock.c:1212
Read of size 8 at addr
ffff8880944904a0 by task syz-fuzzer/9751
Reported-by: syzbot+c3c5bdea7863886115dc@syzkaller.appspotmail.com
Fixes:
6c08fc896b60 ("Bluetooth: Fix refcount use-after-free issue")
Cc: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Steven Price [Tue, 4 Feb 2020 01:35:58 +0000 (17:35 -0800)]
mm: pagewalk: fix termination condition in walk_pte_range()
[ Upstream commit
c02a98753e0a36ba65a05818626fa6adeb4e7c97 ]
If walk_pte_range() is called with a 'end' argument that is beyond the
last page of memory (e.g. ~0UL) then the comparison between 'addr' and
'end' will always fail and the loop will be infinite. Instead change the
comparison to >= while accounting for overflow.
Link: http://lkml.kernel.org/r/20191218162402.45610-15-steven.price@arm.com
Signed-off-by: Steven Price <steven.price@arm.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexandre Ghiti <alex@ghiti.fr>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: "Liang, Kan" <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Zong Li <zong.li@sifive.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Manish Mandlik [Tue, 28 Jan 2020 18:54:14 +0000 (10:54 -0800)]
Bluetooth: Fix refcount use-after-free issue
[ Upstream commit
6c08fc896b60893c5d673764b0668015d76df462 ]
There is no lock preventing both l2cap_sock_release() and
chan->ops->close() from running at the same time.
If we consider Thread A running l2cap_chan_timeout() and Thread B running
l2cap_sock_release(), expected behavior is:
A::l2cap_chan_timeout()->l2cap_chan_close()->l2cap_sock_teardown_cb()
A::l2cap_chan_timeout()->l2cap_sock_close_cb()->l2cap_sock_kill()
B::l2cap_sock_release()->sock_orphan()
B::l2cap_sock_release()->l2cap_sock_kill()
where,
sock_orphan() clears "sk->sk_socket" and l2cap_sock_teardown_cb() marks
socket as SOCK_ZAPPED.
In l2cap_sock_kill(), there is an "if-statement" that checks if both
sock_orphan() and sock_teardown() has been run i.e. sk->sk_socket is NULL
and socket is marked as SOCK_ZAPPED. Socket is killed if the condition is
satisfied.
In the race condition, following occurs:
A::l2cap_chan_timeout()->l2cap_chan_close()->l2cap_sock_teardown_cb()
B::l2cap_sock_release()->sock_orphan()
B::l2cap_sock_release()->l2cap_sock_kill()
A::l2cap_chan_timeout()->l2cap_sock_close_cb()->l2cap_sock_kill()
In this scenario, "if-statement" is true in both B::l2cap_sock_kill() and
A::l2cap_sock_kill() and we hit "refcount: underflow; use-after-free" bug.
Similar condition occurs at other places where teardown/sock_kill is
happening:
l2cap_disconnect_rsp()->l2cap_chan_del()->l2cap_sock_teardown_cb()
l2cap_disconnect_rsp()->l2cap_sock_close_cb()->l2cap_sock_kill()
l2cap_conn_del()->l2cap_chan_del()->l2cap_sock_teardown_cb()
l2cap_conn_del()->l2cap_sock_close_cb()->l2cap_sock_kill()
l2cap_disconnect_req()->l2cap_chan_del()->l2cap_sock_teardown_cb()
l2cap_disconnect_req()->l2cap_sock_close_cb()->l2cap_sock_kill()
l2cap_sock_cleanup_listen()->l2cap_chan_close()->l2cap_sock_teardown_cb()
l2cap_sock_cleanup_listen()->l2cap_sock_kill()
Protect teardown/sock_kill and orphan/sock_kill by adding hold_lock on
l2cap channel to ensure that the socket is killed only after marked as
zapped and orphan.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mert Dirik [Thu, 16 Jan 2020 11:11:25 +0000 (14:11 +0300)]
ar5523: Add USB ID of SMCWUSBT-G2 wireless adapter
[ Upstream commit
5b362498a79631f283578b64bf6f4d15ed4cc19a ]
Add the required USB ID for running SMCWUSBT-G2 wireless adapter (SMC
"EZ Connect g").
This device uses ar5523 chipset and requires firmware to be loaded. Even
though pid of the device is 4507, this patch adds it as 4506 so that
AR5523_DEVICE_UG macro can set the AR5523_FLAG_PRE_FIRMWARE flag for pid
4507.
Signed-off-by: Mert Dirik <mertdirik@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Josef Bacik [Wed, 24 Sep 2014 20:14:12 +0000 (16:14 -0400)]
tracing: Set kernel_stack's caller size properly
[ Upstream commit
cbc3b92ce037f5e7536f6db157d185cd8b8f615c ]
I noticed when trying to use the trace-cmd python interface that reading the raw
buffer wasn't working for kernel_stack events. This is because it uses a
stubbed version of __dynamic_array that doesn't do the __data_loc trick and
encode the length of the array into the field. Instead it just shows up as a
size of 0. So change this to __array and set the len to FTRACE_STACK_ENTRIES
since this is what we actually do in practice and matches how user_stack_trace
works.
Link: http://lkml.kernel.org/r/1411589652-1318-1-git-send-email-jbacik@fb.com
Signed-off-by: Josef Bacik <jbacik@fb.com>
[ Pulled from the archeological digging of my INBOX ]
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Matthias Fend [Wed, 15 Jan 2020 10:22:49 +0000 (11:22 +0100)]
dmaengine: zynqmp_dma: fix burst length configuration
[ Upstream commit
cc88525ebffc757e00cc5a5d61da6271646c7f5f ]
Since the dma engine expects the burst length register content as
power of 2 value, the burst length needs to be converted first.
Additionally add a burst length range check to avoid corrupting unrelated
register bits.
Signed-off-by: Matthias Fend <matthias.fend@wolfvision.net>
Link: https://lore.kernel.org/r/20200115102249.24398-1-matthias.fend@wolfvision.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Rafael J. Wysocki [Fri, 27 Dec 2019 10:04:21 +0000 (11:04 +0100)]
ACPI: EC: Reference count query handlers under lock
[ Upstream commit
3df663a147fe077a6ee8444ec626738946e65547 ]
There is a race condition in acpi_ec_get_query_handler()
theoretically allowing query handlers to go away before refernce
counting them.
In order to avoid it, call kref_get() on query handlers under
ec->mutex.
Also simplify the code a bit while at it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nikhil Devshatwar [Tue, 12 Nov 2019 14:53:33 +0000 (15:53 +0100)]
media: ti-vpe: cal: Restrict DMA to avoid memory corruption
[ Upstream commit
6e72eab2e7b7a157d554b8f9faed7676047be7c1 ]
When setting DMA for video capture from CSI channel, if the DMA size
is not given, it ends up writing as much data as sent by the camera.
This may lead to overwriting the buffers causing memory corruption.
Observed green lines on the default framebuffer.
Restrict the DMA to maximum height as specified in the S_FMT ioctl.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Marco Elver [Thu, 14 Nov 2019 18:03:00 +0000 (19:03 +0100)]
seqlock: Require WRITE_ONCE surrounding raw_seqcount_barrier
[ Upstream commit
bf07132f96d426bcbf2098227fb680915cf44498 ]
This patch proposes to require marked atomic accesses surrounding
raw_write_seqcount_barrier. We reason that otherwise there is no way to
guarantee propagation nor atomicity of writes before/after the barrier
[1]. For example, consider the compiler tears stores either before or
after the barrier; in this case, readers may observe a partial value,
and because readers are unaware that writes are going on (writes are not
in a seq-writer critical section), will complete the seq-reader critical
section while having observed some partial state.
[1] https://lwn.net/Articles/793253/
This came up when designing and implementing KCSAN, because KCSAN would
flag these accesses as data-races. After careful analysis, our reasoning
as above led us to conclude that the best thing to do is to propose an
amendment to the raw_seqcount_barrier usage.
Signed-off-by: Marco Elver <elver@google.com>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vasily Averin [Thu, 23 Jan 2020 07:11:35 +0000 (10:11 +0300)]
rt_cpu_seq_next should increase position index
[ Upstream commit
a3ea86739f1bc7e121d921842f0f4a8ab1af94d9 ]
if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vasily Averin [Thu, 23 Jan 2020 07:11:28 +0000 (10:11 +0300)]
neigh_stat_seq_next() should increase position index
[ Upstream commit
1e3f9f073c47bee7c23e77316b07bc12338c5bba ]
if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Joe Perches [Thu, 5 Dec 2019 00:50:53 +0000 (16:50 -0800)]
kernel/sys.c: avoid copying possible padding bytes in copy_to_user
[ Upstream commit
5e1aada08cd19ea652b2d32a250501d09b02ff2e ]
Initialization is not guaranteed to zero padding bytes so use an
explicit memset instead to avoid leaking any kernel content in any
possible padding bytes.
Link: http://lkml.kernel.org/r/dfa331c00881d61c8ee51577a082d8bebd61805c.camel@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pavel Shilovsky [Tue, 29 Oct 2019 23:51:19 +0000 (16:51 -0700)]
CIFS: Properly process SMB3 lease breaks
[ Upstream commit
9bd4540836684013aaad6070a65d6fcdd9006625 ]
Currenly we doesn't assume that a server may break a lease
from RWH to RW which causes us setting a wrong lease state
on a file and thus mistakenly flushing data and byte-range
locks and purging cached data on the client. This leads to
performance degradation because subsequent IOs go directly
to the server.
Fix this by propagating new lease state and epoch values
to the oplock break handler through cifsFileInfo structure
and removing the use of cifsInodeInfo flags for that. It
allows to avoid some races of several lease/oplock breaks
using those flags in parallel.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Kusanagi Kouichi [Thu, 21 Nov 2019 10:20:21 +0000 (19:20 +0900)]
debugfs: Fix !DEBUG_FS debugfs_create_automount
[ Upstream commit
4250b047039d324e0ff65267c8beb5bad5052a86 ]
If DEBUG_FS=n, compile fails with the following error:
kernel/trace/trace.c: In function 'tracing_init_dentry':
kernel/trace/trace.c:8658:9: error: passing argument 3 of 'debugfs_create_automount' from incompatible pointer type [-Werror=incompatible-pointer-types]
8658 | trace_automount, NULL);
| ^~~~~~~~~~~~~~~
| |
| struct vfsmount * (*)(struct dentry *, void *)
In file included from kernel/trace/trace.c:24:
./include/linux/debugfs.h:206:25: note: expected 'struct vfsmount * (*)(void *)' but argument is of type 'struct vfsmount * (*)(struct dentry *, void *)'
206 | struct vfsmount *(*f)(void *),
| ~~~~~~~~~~~~~~~~~~~^~~~~~~~~~
Signed-off-by: Kusanagi Kouichi <slash@ac.auone-net.jp>
Link: https://lore.kernel.org/r/20191121102021787.MLMY.25002.ppp.dion.ne.jp@dmta0003.auone-net.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Christophe JAILLET [Mon, 23 Sep 2019 19:07:46 +0000 (21:07 +0200)]
RDMA/iw_cgxb4: Fix an error handling path in 'c4iw_connect()'
[ Upstream commit
9067f2f0b41d7e817fc8c5259bab1f17512b0147 ]
We should jump to fail3 in order to undo the 'xa_insert_irq()' call.
Link: https://lore.kernel.org/r/20190923190746.10964-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Brian Foster [Sat, 16 Nov 2019 05:15:08 +0000 (21:15 -0800)]
xfs: fix attr leaf header freemap.size underflow
[ Upstream commit
2a2b5932db67586bacc560cc065d62faece5b996 ]
The leaf format xattr addition helper xfs_attr3_leaf_add_work()
adjusts the block freemap in a couple places. The first update drops
the size of the freemap that the caller had already selected to
place the xattr name/value data. Before the function returns, it
also checks whether the entries array has encroached on a freemap
range by virtue of the new entry addition. This is necessary because
the entries array grows from the start of the block (but end of the
block header) towards the end of the block while the name/value data
grows from the end of the block in the opposite direction. If the
associated freemap is already empty, however, size is zero and the
subtraction underflows the field and causes corruption.
This is reproduced rarely by generic/070. The observed behavior is
that a smaller sized freemap is aligned to the end of the entries
list, several subsequent xattr additions land in larger freemaps and
the entries list expands into the smaller freemap until it is fully
consumed and then underflows. Note that it is not otherwise a
corruption for the entries array to consume an empty freemap because
the nameval list (i.e. the firstused pointer in the xattr header)
starts beyond the end of the corrupted freemap.
Update the freemap size modification to account for the fact that
the freemap entry can be empty and thus stale.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pan Bian [Wed, 6 Nov 2019 06:44:11 +0000 (14:44 +0800)]
RDMA/i40iw: Fix potential use after free
[ Upstream commit
da046d5f895fca18d63b15ac8faebd5bf784e23a ]
Release variable dst after logging dst->error to avoid possible use after
free.
Link: https://lore.kernel.org/r/1573022651-37171-1-git-send-email-bianpan2016@163.com
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Guoju Fang [Wed, 13 Nov 2019 08:03:16 +0000 (16:03 +0800)]
bcache: fix a lost wake-up problem caused by mca_cannibalize_lock
[ Upstream commit
34cf78bf34d48dddddfeeadb44f9841d7864997a ]
This patch fix a lost wake-up problem caused by the race between
mca_cannibalize_lock and bch_cannibalize_unlock.
Consider two processes, A and B. Process A is executing
mca_cannibalize_lock, while process B takes c->btree_cache_alloc_lock
and is executing bch_cannibalize_unlock. The problem happens that after
process A executes cmpxchg and will execute prepare_to_wait. In this
timeslice process B executes wake_up, but after that process A executes
prepare_to_wait and set the state to TASK_INTERRUPTIBLE. Then process A
goes to sleep but no one will wake up it. This problem may cause bcache
device to dead.
Signed-off-by: Guoju Fang <fangguoju@gmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Divya Indi [Wed, 14 Aug 2019 17:55:25 +0000 (10:55 -0700)]
tracing: Adding NULL checks for trace_array descriptor pointer
[ Upstream commit
953ae45a0c25e09428d4a03d7654f97ab8a36647 ]
As part of commit
f45d1225adb0 ("tracing: Kernel access to Ftrace
instances") we exported certain functions. Here, we are adding some additional
NULL checks to ensure safe usage by users of these APIs.
Link: http://lkml.kernel.org/r/1565805327-579-4-git-send-email-divya.indi@oracle.com
Signed-off-by: Divya Indi <divya.indi@oracle.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Lee Jones [Mon, 21 Oct 2019 09:16:34 +0000 (10:16 +0100)]
mfd: mfd-core: Protect against NULL call-back function pointer
[ Upstream commit
b195e101580db390f50b0d587b7f66f241d2bc88 ]
If a child device calls mfd_cell_{en,dis}able() without an appropriate
call-back being set, we are likely to encounter a panic. Avoid this
by adding suitable checking.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hou Tao [Tue, 8 Oct 2019 02:36:37 +0000 (10:36 +0800)]
mtd: cfi_cmdset_0002: don't free cfi->cfiq in error path of cfi_amdstd_setup()
[ Upstream commit
03976af89e3bd9489d542582a325892e6a8cacc0 ]
Else there may be a double-free problem, because cfi->cfiq will
be freed by mtd_do_chip_probe() if both the two invocations of
check_cmd_set() return failure.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Stephen Kitt [Sat, 19 Oct 2019 14:06:34 +0000 (16:06 +0200)]
clk/ti/adpll: allocate room for terminating null
[ Upstream commit
7f6ac72946b88b89ee44c1c527aa8591ac5ffcbe ]
The buffer allocated in ti_adpll_clk_get_name doesn't account for the
terminating null. This patch switches to devm_kasprintf to avoid
overflowing.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lkml.kernel.org/r/20191019140634.15596-1-steve@sk2.org
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dmitry Osipenko [Mon, 4 Nov 2019 21:56:03 +0000 (00:56 +0300)]
PM / devfreq: tegra30: Fix integer overflow on CPU's freq max out
[ Upstream commit
53b4b2aeee26f42cde5ff2a16dd0d8590c51a55a ]
There is another kHz-conversion bug in the code, resulting in integer
overflow. Although, this time the resulting value is
4294966296 and it's
close to ULONG_MAX, which is okay in this case.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Joakim Tjernlund [Thu, 10 Sep 2020 08:53:28 +0000 (10:53 +0200)]
ALSA: usb-audio: Add delay quirk for H570e USB headsets
commit
315c7ad7a701baba28c628c4c5426b3d9617ceed upstream.
Needs the same delay as H650e
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200910085328.19188-1-joakim.tjernlund@infinera.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Wed, 23 Oct 2019 15:46:59 +0000 (16:46 +0100)]
ASoC: kirkwood: fix IRQ error handling
[ Upstream commit
175fc928198236037174e5c5c066fe3c4691903e ]
Propagate the error code from request_irq(), rather than returning
-EBUSY.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1iNIqh-0000tW-EZ@rmk-PC.armlinux.org.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Kangjie Lu [Fri, 18 Oct 2019 04:29:53 +0000 (23:29 -0500)]
gma/gma500: fix a memory disclosure bug due to uninitialized bytes
[ Upstream commit
57a25a5f754ce27da2cfa6f413cfd366f878db76 ]
`best_clock` is an object that may be sent out. Object `clock`
contains uninitialized bytes that are copied to `best_clock`,
which leads to memory disclosure and information leak.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018042953.31099-1-kjlu@umn.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
Fuqian Huang [Fri, 27 Sep 2019 12:15:44 +0000 (20:15 +0800)]
m68k: q40: Fix info-leak in rtc_ioctl
[ Upstream commit
7cf78b6b12fd5550545e4b73b35dca18bd46b44c ]
When the option is RTC_PLL_GET, pll will be copied to userland
via copy_to_user. pll is initialized using mach_get_rtc_pll indirect
call and mach_get_rtc_pll is only assigned with function
q40_get_rtc_pll in arch/m68k/q40/config.c.
In function q40_get_rtc_pll, the field pll_ctrl is not initialized.
This will leak uninitialized stack content to userland.
Fix this by zeroing the uninitialized field.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Link: https://lore.kernel.org/r/20190927121544.7650-1-huangfq.daxian@gmail.com
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Balsundar P [Tue, 15 Oct 2019 06:21:58 +0000 (11:51 +0530)]
scsi: aacraid: fix illegal IO beyond last LBA
[ Upstream commit
c86fbe484c10b2cd1e770770db2d6b2c88801c1d ]
The driver fails to handle data when read or written beyond device reported
LBA, which triggers kernel panic
Link: https://lore.kernel.org/r/1571120524-6037-2-git-send-email-balsundar.p@microsemi.com
Signed-off-by: Balsundar P <balsundar.p@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Lukas Wunner [Tue, 12 May 2020 12:40:01 +0000 (14:40 +0200)]
serial: 8250: Avoid error message on reprobe
commit
e0a851fe6b9b619527bd928aa93caaddd003f70c upstream.
If the call to uart_add_one_port() in serial8250_register_8250_port()
fails, a half-initialized entry in the serial_8250ports[] array is left
behind.
A subsequent reprobe of the same serial port causes that entry to be
reused. Because uart->port.dev is set, uart_remove_one_port() is called
for the half-initialized entry and bails out with an error message:
bcm2835-aux-uart
3f215040.serial: Removing wrong port: (null) != (ptrval)
The same happens on failure of mctrl_gpio_init() since commit
4a96895f74c9 ("tty/serial/8250: use mctrl_gpio helpers").
Fix by zeroing the uart->port.dev pointer in the probe error path.
The bug was introduced in v2.6.10 by historical commit
befff6f5bf5f
("[SERIAL] Add new port registration/unregistration functions."):
https://git.kernel.org/tglx/history/c/
befff6f5bf5f
The commit added an unconditional call to uart_remove_one_port() in
serial8250_register_port(). In v3.7, commit
835d844d1a28 ("8250_pnp:
do pnp probe before legacy probe") made that call conditional on
uart->port.dev which allows me to fix the issue by zeroing that pointer
in the error path. Thus, the present commit will fix the problem as far
back as v3.7 whereas still older versions need to also cherry-pick
835d844d1a28.
Fixes:
835d844d1a28 ("8250_pnp: do pnp probe before legacy probe")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v2.6.10
Cc: stable@vger.kernel.org # v2.6.10: 835d844d1a28: 8250_pnp: do pnp probe before legacy
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/b4a072013ee1a1d13ee06b4325afb19bda57ca1b.1589285873.git.lukas@wunner.de
[iwamatsu: Backported to 4.4, 4.9: adjust context]
Signed-off-by: Nobuhiro Iwamatsu (CIP) <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Wed, 9 Sep 2020 08:27:40 +0000 (01:27 -0700)]
net: add __must_check to skb_put_padto()
[ Upstream commit
4a009cb04aeca0de60b73f37b102573354214b52 ]
skb_put_padto() and __skb_put_padto() callers
must check return values or risk use-after-free.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Florian Fainelli [Mon, 21 Aug 2017 19:59:10 +0000 (12:59 -0700)]
net/hsr: Check skb_put_padto() return value
commit
414e7d76af6d3ec2dd4e9079927dbe0e2e4ca914 upstream.
skb_put_padto() will free the sk_buff passed as reference in case of
errors, but we still need to check its return value and decide what to
do.
Detected by CoverityScan, CID#
1416688 ("CHECKED_RETURN")
Fixes:
ee1c27977284 ("net/hsr: Added support for HSR v1")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Florian Fainelli [Thu, 17 Sep 2020 03:43:09 +0000 (20:43 -0700)]
net: phy: Avoid NPD upon phy_detach() when driver is unbound
[ Upstream commit
c2b727df7caa33876e7066bde090f40001b6d643 ]
If we have unbound the PHY driver prior to calling phy_detach() (often
via phy_disconnect()) then we can cause a NULL pointer de-reference
accessing the driver owner member. The steps to reproduce are:
echo unimac-mdio-0:01 > /sys/class/net/eth0/phydev/driver/unbind
ip link set eth0 down
Fixes:
cafe8df8b9bc ("net: phy: Fix lack of reference count on PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Chan [Mon, 21 Sep 2020 01:08:56 +0000 (21:08 -0400)]
bnxt_en: Protect bnxt_set_eee() and bnxt_set_pauseparam() with mutex.
[ Upstream commit
a53906908148d64423398a62c4435efb0d09652c ]
All changes related to bp->link_info require the protection of the
link_lock mutex. It's not sufficient to rely just on RTNL.
Fixes:
163e9ef63641 ("bnxt_en: Fix race when modifying pause settings.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xin Long [Sun, 13 Sep 2020 11:37:31 +0000 (19:37 +0800)]
tipc: use skb_unshare() instead in tipc_buf_append()
[ Upstream commit
ff48b6222e65ebdba5a403ef1deba6214e749193 ]
In tipc_buf_append() it may change skb's frag_list, and it causes
problems when this skb is cloned. skb_unclone() doesn't really
make this skb's flag_list available to change.
Shuang Li has reported an use-after-free issue because of this
when creating quite a few macvlan dev over the same dev, where
the broadcast packets will be cloned and go up to the stack:
[ ] BUG: KASAN: use-after-free in pskb_expand_head+0x86d/0xea0
[ ] Call Trace:
[ ] dump_stack+0x7c/0xb0
[ ] print_address_description.constprop.7+0x1a/0x220
[ ] kasan_report.cold.10+0x37/0x7c
[ ] check_memory_region+0x183/0x1e0
[ ] pskb_expand_head+0x86d/0xea0
[ ] process_backlog+0x1df/0x660
[ ] net_rx_action+0x3b4/0xc90
[ ]
[ ] Allocated by task 1786:
[ ] kmem_cache_alloc+0xbf/0x220
[ ] skb_clone+0x10a/0x300
[ ] macvlan_broadcast+0x2f6/0x590 [macvlan]
[ ] macvlan_process_broadcast+0x37c/0x516 [macvlan]
[ ] process_one_work+0x66a/0x1060
[ ] worker_thread+0x87/0xb10
[ ]
[ ] Freed by task 3253:
[ ] kmem_cache_free+0x82/0x2a0
[ ] skb_release_data+0x2c3/0x6e0
[ ] kfree_skb+0x78/0x1d0
[ ] tipc_recvmsg+0x3be/0xa40 [tipc]
So fix it by using skb_unshare() instead, which would create a new
skb for the cloned frag and it'll be safe to change its frag_list.
The similar things were also done in sctp_make_reassembled_event(),
which is using skb_copy().
Reported-by: Shuang Li <shuali@redhat.com>
Fixes:
37e22164a8a3 ("tipc: rename and move message reassembly function")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wei Wang [Tue, 8 Sep 2020 21:09:34 +0000 (14:09 -0700)]
ip: fix tos reflection in ack and reset packets
[ Upstream commit
ba9e04a7ddf4f22a10e05bf9403db6b97743c7bf ]
Currently, in tcp_v4_reqsk_send_ack() and tcp_v4_send_reset(), we
echo the TOS value of the received packets in the response.
However, we do not want to echo the lower 2 ECN bits in accordance
with RFC 3168 6.1.5 robustness principles.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Wed, 9 Sep 2020 09:46:48 +0000 (12:46 +0300)]
hdlc_ppp: add range checks in ppp_cp_parse_cr()
[ Upstream commit
66d42ed8b25b64eb63111a2b8582c5afc8bf1105 ]
There are a couple bugs here:
1) If opt[1] is zero then this results in a forever loop. If the value
is less than 2 then it is invalid.
2) It assumes that "len" is more than sizeof(valid_accm) or 6 which can
result in memory corruption.
In the case of LCP_OPTION_ACCM, then we should check "opt[1]" instead
of "len" because, if "opt[1]" is less than sizeof(valid_accm) then
"nak_len" gets out of sync and it can lead to memory corruption in the
next iterations through the loop. In case of LCP_OPTION_MAGIC, the
only valid value for opt[1] is 6, but the code is trying to log invalid
data so we should only discard the data when "len" is less than 6
because that leads to a read overflow.
Reported-by: ChenNan Of Chaitin Security Research Lab <whutchennan@gmail.com>
Fixes:
e022c2f07ae5 ("WAN: new synchronous PPP implementation for generic HDLC.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Hutchings [Thu, 24 Sep 2020 10:00:54 +0000 (19:00 +0900)]
mtd: Fix comparison in map_word_andequal()
commit
ea739a287f4f16d6250bea779a1026ead79695f2 upstream.
Commit
9e343e87d2c4 ("mtd: cfi: convert inline functions to macros")
changed map_word_andequal() into a macro, but also changed the right
hand side of the comparison from val3 to val2. Change it back to use
val3 on the right hand side.
Thankfully this did not cause a regression because all callers
currently pass the same argument for val2 and val3.
Fixes:
9e343e87d2c4 ("mtd: cfi: convert inline functions to macros")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Nobuhiro Iwamatsu (CIP) <noburhio1.nobuhiro@toshiba.co.jp>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Shamir Rabinovitch [Thu, 24 Sep 2020 09:24:49 +0000 (18:24 +0900)]
RDMA/ucma: ucma_context reference leak in error path
commit
ef95a90ae6f4f21990e1f7ced6719784a409e811 upstream.
Validating input parameters should be done before getting the cm_id
otherwise it can leak a cm_id reference.
Fixes:
6a21dfc0d0db ("RDMA/ucma: Limit possible option size")
Signed-off-by: Shamir Rabinovitch <shamir.rabinovitch@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
[iwamatsu: Backported to 4.4, 4.9 and 4.14: adjust context]
Signed-off-by: Nobuhiro Iwamatsu (CIP) <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Muchun Song [Sat, 19 Sep 2020 04:20:21 +0000 (21:20 -0700)]
kprobes: fix kill kprobe which has been marked as gone
[ Upstream commit
b0399092ccebd9feef68d4ceb8d6219a8c0caa05 ]
If a kprobe is marked as gone, we should not kill it again. Otherwise, we
can disarm the kprobe more than once. In that case, the statistics of
kprobe_ftrace_enabled can unbalance which can lead to that kprobe do not
work.
Fixes:
e8386a0cb22f ("kprobes: support probing module __exit function")
Co-developed-by: Chengming Zhou <zhouchengming@bytedance.com>
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: "Naveen N . Rao" <naveen.n.rao@linux.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Song Liu <songliubraving@fb.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20200822030055.32383-1-songmuchun@bytedance.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Rustam Kovhaev [Mon, 7 Sep 2020 18:55:35 +0000 (11:55 -0700)]
KVM: fix memory leak in kvm_io_bus_unregister_dev()
[ Upstream commit
f65886606c2d3b562716de030706dfe1bea4ed5e ]
when kmalloc() fails in kvm_io_bus_unregister_dev(), before removing
the bus, we should iterate over all other devices linked to it and call
kvm_iodevice_destructor() for them
Fixes:
90db10434b16 ("KVM: kvm_io_bus_unregister_dev() should never fail")
Cc: stable@vger.kernel.org
Reported-and-tested-by: syzbot+f196caa45793d6374707@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=f196caa45793d6374707
Signed-off-by: Rustam Kovhaev <rkovhaev@gmail.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <
20200907185535.233114-1-rkovhaev@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mark Salyzyn [Wed, 22 Jul 2020 11:00:53 +0000 (04:00 -0700)]
af_key: pfkey_dump needs parameter validation
commit
37bd22420f856fcd976989f1d4f1f7ad28e1fcac upstream.
In pfkey_dump() dplen and splen can both be specified to access the
xfrm_address_t structure out of bounds in__xfrm_state_filter_match()
when it calls addr_match() with the indexes. Return EINVAL if either
are out of range.
Signed-off-by: Mark Salyzyn <salyzyn@android.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: kernel-team@android.com
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Wed, 23 Sep 2020 06:46:17 +0000 (08:46 +0200)]
Linux 4.9.237
Link: https://lore.kernel.org/lkml/20200921162035.136047591@linuxfoundation.org/
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adam Borowski [Tue, 9 Oct 2018 06:28:03 +0000 (08:28 +0200)]
x86/defconfig: Enable CONFIG_USB_XHCI_HCD=y
commit
72a9c673636b779e370983fea08e40f97039b981 upstream.
A spanking new machine I just got has all but one USB ports wired as 3.0.
Booting defconfig resulted in no keyboard or mouse, which was pretty
uncool. Let's enable that -- USB3 is ubiquitous rather than an oddity.
As 'y' not 'm' -- recovering from initrd problems needs a keyboard.
Also add it to the 32-bit defconfig.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-usb@vger.kernel.org
Link: http://lkml.kernel.org/r/20181009062803.4332-1-kilobyte@angband.pl
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexey Kardashevskiy [Tue, 8 Sep 2020 01:51:06 +0000 (11:51 +1000)]
powerpc/dma: Fix dma_map_ops::get_required_mask
commit
437ef802e0adc9f162a95213a3488e8646e5fc03 upstream.
There are 2 problems with it:
1. "<" vs expected "<<"
2. the shift number is an IOMMU page number mask, not an address
mask as the IOMMU page shift is missing.
This did not hit us before
f1565c24b596 ("powerpc: use the generic
dma_ops_bypass mode") because we had additional code to handle bypass
mask so this chunk (almost?) never executed.However there were
reports that aacraid does not work with "iommu=nobypass".
After
f1565c24b596, aacraid (and probably others which call
dma_get_required_mask() before setting the mask) was unable to enable
64bit DMA and fall back to using IOMMU which was known not to work,
one of the problems is double free of an IOMMU page.
This fixes DMA for aacraid, both with and without "iommu=nobypass" in
the kernel command line. Verified with "stress-ng -d 4".
Fixes:
6a5c7be5e484 ("powerpc: Override dma_get_required_mask by platform hook and ops")
Cc: stable@vger.kernel.org # v3.2+
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200908015106.79661-1-aik@ozlabs.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quentin Perret [Wed, 16 Sep 2020 17:18:25 +0000 (18:18 +0100)]
ehci-hcd: Move include to keep CRC stable
commit
29231826f3bd65500118c473fccf31c0cf14dbc0 upstream.
The CRC calculation done by genksyms is triggered when the parser hits
EXPORT_SYMBOL*() macros. At this point, genksyms recursively expands the
types of the function parameters, and uses that as the input for the CRC
calculation. In the case of forward-declared structs, the type expands
to 'UNKNOWN'. Following this, it appears that the result of the
expansion of each type is cached somewhere, and seems to be re-used
when/if the same type is seen again for another exported symbol in the
same C file.
Unfortunately, this can cause CRC 'stability' issues when a struct
definition becomes visible in the middle of a C file. For example, let's
assume code with the following pattern:
struct foo;
int bar(struct foo *arg)
{
/* Do work ... */
}
EXPORT_SYMBOL_GPL(bar);
/* This contains struct foo's definition */
#include "foo.h"
int baz(struct foo *arg)
{
/* Do more work ... */
}
EXPORT_SYMBOL_GPL(baz);
Here, baz's CRC will be computed using the expansion of struct foo that
was cached after bar's CRC calculation ('UNKOWN' here). But if
EXPORT_SYMBOL_GPL(bar) is removed from the file (because of e.g. symbol
trimming using CONFIG_TRIM_UNUSED_KSYMS), struct foo will be expanded
late, during baz's CRC calculation, which now has visibility over the
full struct definition, hence resulting in a different CRC for baz.
The proper fix for this certainly is in genksyms, but that will take me
some time to get right. In the meantime, we have seen one occurrence of
this in the ehci-hcd code which hits this problem because of the way it
includes C files halfway through the code together with an unlucky mix
of symbol trimming.
In order to workaround this, move the include done in ehci-hub.c early
in ehci-hcd.c, hence making sure the struct definitions are visible to
the entire file. This improves CRC stability of the ehci-hcd exports
even when symbol trimming is enabled.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20200916171825.3228122-1-qperret@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tobias Diedrich [Mon, 14 Sep 2020 17:36:28 +0000 (19:36 +0200)]
serial: 8250_pci: Add Realtek 816a and 816b
commit
3c5a87be170aba8ac40982182f812dcff6ed1ad1 upstream.
These serial ports are exposed by the OOB-management-engine on
RealManage-enabled network cards (e.g. AMD DASH enabled systems using
Realtek cards).
Because these have 3 BARs, they fail the "num_iomem <= 1" check in
serial_pci_guess_board.
I've manually checked the two IOMEM regions and BAR 2 doesn't seem to
respond to reads, but BAR 4 seems to be an MMIO version of the IO ports
(untested).
With this change, the ports are detected:
0000:02:00.1: ttyS0 at I/O 0x2200 (irq = 82, base_baud = 115200) is a 16550A
0000:02:00.2: ttyS1 at I/O 0x2100 (irq = 55, base_baud = 115200) is a 16550A
lspci output:
02:00.1 0700: 10ec:816a (rev 0e) (prog-if 02 [16550])
Subsystem: 17aa:5082
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 82
IOMMU group: 11
Region 0: I/O ports at 2200 [size=256]
Region 2: Memory at
fd715000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at
fd704000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address:
0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 01
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+
10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- TPHComp- ExtTPHComp-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled,
AtomicOpsCtl: ReqEn-
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
Vector table: BAR=4 offset=
00000000
PBA: BAR=4 offset=
00000800
Capabilities: [d0] Vital Product Data
Not readable
Capabilities: [100 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog:
00000000 00000000 00000000 00000000
Capabilities: [160 v1] Device Serial Number 00-00-00-00-00-00-00-00
Capabilities: [170 v1] Latency Tolerance Reporting
Max snoop latency: 0ns
Max no snoop latency: 0ns
Capabilities: [178 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
PortCommonModeRestoreTime=150us PortTPowerOnTime=150us
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
T_CommonMode=0us LTR1.2_Threshold=0ns
L1SubCtl2: T_PwrOn=10us
02:00.2 0700: 10ec:816b (rev 0e)
[...same...]
Signed-off-by: Tobias Diedrich <tobiasdiedrich@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200914173628.GA22508@yamamaya.is-a-geek.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Tue, 8 Sep 2020 23:27:29 +0000 (16:27 -0700)]
Input: i8042 - add Entroware Proteus EL07R4 to nomux and reset lists
commit
c4440b8a457779adeec42c5e181cb4016f19ce0f upstream.
The keyboard drops keypresses early during boot unless both the nomux
and reset quirks are set. Add DMI table entries for this.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1806085
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200907095656.13155-1-hdegoede@redhat.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oliver Neukum [Thu, 17 Sep 2020 10:34:27 +0000 (12:34 +0200)]
usblp: fix race between disconnect() and read()
commit
9cdabcb3ef8c24ca3a456e4db7b012befb688e73 upstream.
read() needs to check whether the device has been
disconnected before it tries to talk to the device.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+be5b5f86a162a6c281e6@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20200917103427.15740-1-oneukum@suse.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oliver Neukum [Wed, 16 Sep 2020 09:40:25 +0000 (11:40 +0200)]
USB: UAS: fix disconnect by unplugging a hub
commit
325b008723b2dd31de020e85ab9d2e9aa4637d35 upstream.
The SCSI layer can go into an ugly loop if you ignore that a device is
gone. You need to report an error in the command rather than in the
return value of the queue method.
We need to specifically check for ENODEV. The issue goes back to the
introduction of the driver.
Fixes:
115bb1ffa54c3 ("USB: Add UAS driver")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200916094026.30085-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Penghao [Mon, 7 Sep 2020 02:30:26 +0000 (10:30 +0800)]
USB: quirks: Add USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk for BYD zhaoxin notebook
commit
bcea6dafeeef7d1a6a8320a249aabf981d63b881 upstream.
Add a USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk for the BYD zhaoxin notebook.
This notebook come with usb touchpad. And we would like to disable
touchpad wakeup on this notebook by default.
Signed-off-by: Penghao <penghao@uniontech.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200907023026.28189-1-penghao@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yu Kuai [Wed, 9 Sep 2020 08:49:42 +0000 (16:49 +0800)]
drm/mediatek: Add exception handing in mtk_drm_probe() if component init fail
[ Upstream commit
64c194c00789889b0f9454f583712f079ba414ee ]
mtk_ddp_comp_init() is called in a loop in mtk_drm_probe(), if it
fail, previous successive init component is not proccessed.
Thus uninitialize valid component and put their device if component
init failed.
Fixes:
119f5173628a ("drm/mediatek: Add DRM Driver for Mediatek SoC MT8173.")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Thomas Bogendoerfer [Wed, 16 Sep 2020 13:54:37 +0000 (15:54 +0200)]
MIPS: SNI: Fix spurious interrupts
[ Upstream commit
b959b97860d0fee8c8f6a3e641d3c2ad76eab6be ]
On A20R machines the interrupt pending bits in cause register need to be
updated by requesting the chipset to do it. This needs to be done to
find the interrupt cause and after interrupt service. In
commit
0b888c7f3a03 ("MIPS: SNI: Convert to new irq_chip functions") the
function to do after service update got lost, which caused spurious
interrupts.
Fixes:
0b888c7f3a03 ("MIPS: SNI: Convert to new irq_chip functions")
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tetsuo Handa [Thu, 10 Sep 2020 22:57:06 +0000 (07:57 +0900)]
fbcon: Fix user font detection test at fbcon_resize().
[ Upstream commit
ec0972adecb391a8d8650832263a4790f3bfb4df ]
syzbot is reporting OOB read at fbcon_resize() [1], for
commit
39b3cffb8cf31117 ("fbcon: prevent user font height or width change
from causing potential out-of-bounds access") is by error using
registered_fb[con2fb_map[vc->vc_num]]->fbcon_par->p->userfont (which was
set to non-zero) instead of fb_display[vc->vc_num].userfont (which remains
zero for that display).
We could remove tricky userfont flag [2], for we can determine it by
comparing address of the font data and addresses of built-in font data.
But since that commit is failing to fix the original OOB read [3], this
patch keeps the change minimal in case we decide to revert altogether.
[1] https://syzkaller.appspot.com/bug?id=
ebcbbb6576958a496500fee9cf7aa83ea00b5920
[2] https://syzkaller.appspot.com/text?tag=Patch&x=
14030853900000
[3] https://syzkaller.appspot.com/bug?id=
6fba8c186d97cf1011ab17660e633b1cc4e080c9
Reported-by: syzbot <syzbot+b38b1ef6edf0c74a8d97@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes:
39b3cffb8cf31117 ("fbcon: prevent user font height or width change from causing potential out-of-bounds access")
Cc: George Kennedy <george.kennedy@oracle.com>
Link: https://lore.kernel.org/r/f6e3e611-8704-1263-d163-f52c906a4f06@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Namhyung Kim [Tue, 15 Sep 2020 03:18:19 +0000 (12:18 +0900)]
perf test: Free formats for perf pmu parse test
[ Upstream commit
d26383dcb2b4b8629fde05270b4e3633be9e3d4b ]
The following leaks were detected by ASAN:
Indirect leak of 360 byte(s) in 9 object(s) allocated from:
#0 0x7fecc305180e in calloc (/lib/x86_64-linux-gnu/libasan.so.5+0x10780e)
#1 0x560578f6dce5 in perf_pmu__new_format util/pmu.c:1333
#2 0x560578f752fc in perf_pmu_parse util/pmu.y:59
#3 0x560578f6a8b7 in perf_pmu__format_parse util/pmu.c:73
#4 0x560578e07045 in test__pmu tests/pmu.c:155
#5 0x560578de109b in run_test tests/builtin-test.c:410
#6 0x560578de109b in test_and_print tests/builtin-test.c:440
#7 0x560578de401a in __cmd_test tests/builtin-test.c:661
#8 0x560578de401a in cmd_test tests/builtin-test.c:807
#9 0x560578e49354 in run_builtin /home/namhyung/project/linux/tools/perf/perf.c:312
#10 0x560578ce71a8 in handle_internal_command /home/namhyung/project/linux/tools/perf/perf.c:364
#11 0x560578ce71a8 in run_argv /home/namhyung/project/linux/tools/perf/perf.c:408
#12 0x560578ce71a8 in main /home/namhyung/project/linux/tools/perf/perf.c:538
#13 0x7fecc2b7acc9 in __libc_start_main ../csu/libc-start.c:308
Fixes:
cff7f956ec4a1 ("perf tests: Move pmu tests into separate object")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20200915031819.386559-12-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Thomas Bogendoerfer [Mon, 14 Sep 2020 16:05:00 +0000 (18:05 +0200)]
MIPS: SNI: Fix MIPS_L1_CACHE_SHIFT
[ Upstream commit
564c836fd945a94b5dd46597d6b7adb464092650 ]
Commit
930beb5ac09a ("MIPS: introduce MIPS_L1_CACHE_SHIFT_<N>") forgot
to select the correct MIPS_L1_CACHE_SHIFT for SNI RM. This breaks non
coherent DMA because of a wrong allocation alignment.
Fixes:
930beb5ac09a ("MIPS: introduce MIPS_L1_CACHE_SHIFT_<N>")
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Michael Kelley [Sun, 13 Sep 2020 19:47:29 +0000 (12:47 -0700)]
Drivers: hv: vmbus: Add timeout to vmbus_wait_for_unload
[ Upstream commit
911e1987efc8f3e6445955fbae7f54b428b92bd3 ]
vmbus_wait_for_unload() looks for a CHANNELMSG_UNLOAD_RESPONSE message
coming from Hyper-V. But if the message isn't found for some reason,
the panic path gets hung forever. Add a timeout of 10 seconds to prevent
this.
Fixes:
415719160de3 ("Drivers: hv: vmbus: avoid scheduling in interrupt context in vmbus_initiate_unload()")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Link: https://lore.kernel.org/r/1600026449-23651-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nathan Chancellor [Mon, 10 Aug 2020 04:40:20 +0000 (21:40 -0700)]
clk: rockchip: Fix initialization of mux_pll_src_4plls_p
[ Upstream commit
e9c006bc782c488f485ffe50de20b44e1e3daa18 ]
A new warning in Clang points out that the initialization of
mux_pll_src_4plls_p appears incorrect:
../drivers/clk/rockchip/clk-rk3228.c:140:58: warning: suspicious
concatenation of string literals in an array initialization; did you
mean to separate the elements with a comma? [-Wstring-concatenation]
PNAME(mux_pll_src_4plls_p) = { "cpll", "gpll", "hdmiphy" "usb480m" };
^
,
../drivers/clk/rockchip/clk-rk3228.c:140:48: note: place parentheses
around the string literal to silence warning
PNAME(mux_pll_src_4plls_p) = { "cpll", "gpll", "hdmiphy" "usb480m" };
^
1 warning generated.
Given the name of the variable and the same variable name in rv1108, it
seems that this should have been four distinct elements. Fix it up by
adding the comma as suggested.
Fixes:
307a2e9ac524 ("clk: rockchip: add clock controller for rk3228")
Link: https://github.com/ClangBuiltLinux/linux/issues/1123
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20200810044020.2063350-1-natechancellor@gmail.com
Reviewed-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Evan Nimmo [Tue, 8 Sep 2020 20:32:47 +0000 (08:32 +1200)]
i2c: algo: pca: Reapply i2c bus settings after reset
[ Upstream commit
0a355aeb24081e4538d4d424cd189f16c0bbd983 ]
If something goes wrong (such as the SCL being stuck low) then we need
to reset the PCA chip. The issue with this is that on reset we lose all
config settings and the chip ends up in a disabled state which results
in a lock up/high CPU usage. We need to re-apply any configuration that
had previously been set and re-enable the chip.
Signed-off-by: Evan Nimmo <evan.nimmo@alliedtelesis.co.nz>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Laurent Pinchart [Tue, 28 Jul 2020 22:19:40 +0000 (01:19 +0300)]
rapidio: Replace 'select' DMAENGINES 'with depends on'
[ Upstream commit
d2b86100245080cfdf1e95e9e07477474c1be2bd ]
Enabling a whole subsystem from a single driver 'select' is frowned
upon and won't be accepted in new drivers, that need to use 'depends on'
instead. Existing selection of DMAENGINES will then cause circular
dependencies. Replace them with a dependency.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
J. Bruce Fields [Sat, 5 Sep 2020 14:03:26 +0000 (10:03 -0400)]
SUNRPC: stop printk reading past end of string
[ Upstream commit
8c6b6c793ed32b8f9770ebcdf1ba99af423c303b ]
Since p points at raw xdr data, there's no guarantee that it's NULL
terminated, so we should give a length. And probably escape any special
characters too.
Reported-by: Zhi Li <yieli@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vincent Whitchurch [Wed, 2 Sep 2020 13:23:41 +0000 (15:23 +0200)]
spi: spi-loopback-test: Fix out-of-bounds read
[ Upstream commit
837ba18dfcd4db21ad58107c65bfe89753aa56d7 ]
The "tx/rx-transfer - crossing PAGE_SIZE" test always fails when
len=131071 and rx_offset >= 5:
spi-loopback-test spi0.0: Running test tx/rx-transfer - crossing PAGE_SIZE
...
with iteration values: len = 131071, tx_off = 0, rx_off = 3
with iteration values: len = 131071, tx_off = 0, rx_off = 4
with iteration values: len = 131071, tx_off = 0, rx_off = 5
loopback strangeness - rx changed outside of allowed range at: ...
a4321000
spi_msg@
ffffffd5a4157690
frame_length: 131071
actual_length: 131071
spi_transfer@
ffffffd5a41576f8
len: 131071
tx_buf:
ffffffd5a4340ffc
Note that rx_offset > 3 can only occur if the SPI controller driver sets
->dma_alignment to a higher value than 4, so most SPI controller drivers
are not affect.
The allocated Rx buffer is of size SPI_TEST_MAX_SIZE_PLUS, which is 132
KiB (assuming 4 KiB pages). This test uses an initial offset into the
rx_buf of PAGE_SIZE - 4, and a len of 131071, so the range expected to
be written in this transfer ends at (4096 - 4) + 5 + 131071 == 132 KiB,
which is also the end of the allocated buffer. But the code which
verifies the content of the buffer reads a byte beyond the allocated
buffer and spuriously fails because this out-of-bounds read doesn't
return the expected value.
Fix this by using ITERATE_LEN instead of ITERATE_MAX_LEN to avoid
testing sizes which cause out-of-bounds reads.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20200902132341.7079-1-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
James Smart [Fri, 28 Aug 2020 17:53:30 +0000 (10:53 -0700)]
scsi: lpfc: Fix FLOGI/PLOGI receive race condition in pt2pt discovery
[ Upstream commit
7b08e89f98cee9907895fabb64cf437bc505ce9a ]
The driver is unable to successfully login with remote device. During pt2pt
login, the driver completes its FLOGI request with the remote device having
WWN precedence. The remote device issues its own (delayed) FLOGI after
accepting the driver's and, upon transmitting the FLOGI, immediately
recognizes it has already processed the driver's FLOGI thus it transitions
to sending a PLOGI before waiting for an ACC to its FLOGI.
In the driver, the FLOGI is received and an ACC sent, followed by the PLOGI
being received and an ACC sent. The issue is that the PLOGI reception
occurs before the response from the adapter from the FLOGI ACC is
received. Processing of the PLOGI sets state flags to perform the REG_RPI
mailbox command and proceed with the rest of discovery on the port. The
same completion routine used by both FLOGI and PLOGI is generic in
nature. One of the things it does is clear flags, and those flags happen to
drive the rest of discovery. So what happened was the PLOGI processing set
the flags, the FLOGI ACC completion cleared them, thus when the PLOGI ACC
completes it doesn't see the flags and stops.
Fix by modifying the generic completion routine to not clear the rest of
discovery flag (NLP_ACC_REGLOGIN) unless the completion is also associated
with performing a mailbox command as part of its handling. For things such
as FLOGI ACC, there isn't a subsequent action to perform with the adapter,
thus there is no mailbox cmd ptr. PLOGI ACC though will perform REG_RPI
upon completion, thus there is a mailbox cmd ptr.
Link: https://lore.kernel.org/r/20200828175332.130300-3-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dinghao Liu [Sun, 23 Aug 2020 09:14:53 +0000 (17:14 +0800)]
scsi: pm8001: Fix memleak in pm8001_exec_internal_task_abort
[ Upstream commit
ea403fde7552bd61bad6ea45e3feb99db77cb31e ]
When pm8001_tag_alloc() fails, task should be freed just like it is done in
the subsequent error paths.
Link: https://lore.kernel.org/r/20200823091453.4782-1-dinghao.liu@zju.edu.cn
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Olga Kornievskaia [Thu, 20 Aug 2020 22:52:43 +0000 (18:52 -0400)]
NFSv4.1 handle ERR_DELAY error reclaiming locking state on delegation recall
[ Upstream commit
3d7a9520f0c3e6a68b6de8c5812fc8b6d7a52626 ]
A client should be able to handle getting an ERR_DELAY error
while doing a LOCK call to reclaim state due to delegation being
recalled. This is a transient error that can happen due to server
moving its volumes and invalidating its file location cache and
upon reference to it during the LOCK call needing to do an
expensive lookup (leading to an ERR_DELAY error on a PUTFH).
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Miaohe Lin [Sat, 15 Aug 2020 08:46:41 +0000 (04:46 -0400)]
net: handle the return value of pskb_carve_frag_list() correctly
commit
eabe861881a733fc84f286f4d5a1ffaddd4f526f upstream.
pskb_carve_frag_list() may return -ENOMEM in pskb_carve_inside_nonlinear().
we should handle this correctly or we would get wrong sk_buff.
Fixes:
6fa01ccd8830 ("skbuff: Add pskb_extract() helper function")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Oberparleiter [Thu, 10 Sep 2020 12:52:01 +0000 (14:52 +0200)]
gcov: add support for GCC 10.1
[ Upstream commit
40249c6962075c040fd071339acae524f18bfac9 ]
Using gcov to collect coverage data for kernels compiled with GCC 10.1
causes random malfunctions and kernel crashes. This is the result of a
changed GCOV_COUNTERS value in GCC 10.1 that causes a mismatch between
the layout of the gcov_info structure created by GCC profiling code and
the related structure used by the kernel.
Fix this by updating the in-kernel GCOV_COUNTERS value. Also re-enable
config GCOV_KERNEL for use with GCC 10.
Reported-by: Colin Ian King <colin.king@canonical.com>
Reported-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Tested-by: Leon Romanovsky <leonro@nvidia.com>
Tested-and-Acked-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yi Zhang [Thu, 20 Aug 2020 15:36:46 +0000 (23:36 +0800)]
RDMA/rxe: Fix the parent sysfs read when the interface has 15 chars
[ Upstream commit
60b1af64eb35074a4f2d41cc1e503a7671e68963 ]
'parent' sysfs reads will yield '\0' bytes when the interface name has 15
chars, and there will no "\n" output.
To reproduce, create one interface with 15 chars:
[root@test ~]# ip a s enp0s29u1u7u3c2
2: enp0s29u1u7u3c2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UNKNOWN group default qlen 1000
link/ether 02:21:28:57:47:17 brd ff:ff:ff:ff:ff:ff
inet6 fe80::ac41:338f:5bcd:c222/64 scope link noprefixroute
valid_lft forever preferred_lft forever
[root@test ~]# modprobe rdma_rxe
[root@test ~]# echo enp0s29u1u7u3c2 > /sys/module/rdma_rxe/parameters/add
[root@test ~]# cat /sys/class/infiniband/rxe0/parent
enp0s29u1u7u3c2[root@test ~]#
[root@test ~]# f="/sys/class/infiniband/rxe0/parent"
[root@test ~]# echo "$(<"$f")"
-bash: warning: command substitution: ignored null byte in input
enp0s29u1u7u3c2
Use scnprintf and PAGE_SIZE to fill the sysfs output buffer.
Cc: stable@vger.kernel.org
Fixes:
8700e3e7c485 ("Soft RoCE driver")
Link: https://lore.kernel.org/r/20200820153646.31316-1-yi.zhang@redhat.com
Suggested-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Yi Zhang <yi.zhang@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Bart Van Assche [Tue, 10 Jan 2017 19:15:53 +0000 (11:15 -0800)]
IB/rxe: Remove a pointless indirection layer
[ Upstream commit
839f5ac0d806970a102117be03ef05272c50d20e ]
Neither rxe->ifc_ops nor any of the function pointers in struct
struct rxe_ifc_ops ever change. Hence remove the rxe->ifc_ops
indirection mechanism.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Andrew Boyer <andrew.boyer@dell.com>
Cc: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mathias Nyman [Tue, 1 Sep 2020 08:25:28 +0000 (11:25 +0300)]
usb: Fix out of sync data toggle if a configured device is reconfigured
commit
cfd54fa83a5068b61b7eb28d3c117d8354c74c7a upstream.
Userspace drivers that use a SetConfiguration() request to "lightweight"
reset an already configured usb device might cause data toggles to get out
of sync between the device and host, and the device becomes unusable.
The xHCI host requires endpoints to be dropped and added back to reset the
toggle. If USB core notices the new configuration is the same as the
current active configuration it will avoid these extra steps by calling
usb_reset_configuration() instead of usb_set_configuration().
A SetConfiguration() request will reset the device side data toggles.
Make sure usb_reset_configuration() function also drops and adds back the
endpoints to ensure data toggles are in sync.
To avoid code duplication split the current usb_disable_device() function
and reuse the endpoint specific part.
Cc: stable <stable@vger.kernel.org>
Tested-by: Martin Thierer <mthierer@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200901082528.12557-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aleksander Morgado [Sat, 29 Aug 2020 09:05:39 +0000 (11:05 +0200)]
USB: serial: option: add support for SIM7070/SIM7080/SIM7090 modules
commit
1ac698790819b83f39fd7ea4f6cdabee9bdd7b38 upstream.
These modules have 2 different USB layouts:
The default layout with PID 0x9205 (AT+CUSBSELNV=1) exposes 4 TTYs and
an ECM interface:
T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 6 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1e0e ProdID=9205 Rev=00.00
S: Manufacturer=SimTech, Incorporated
S: Product=SimTech SIM7080
S: SerialNumber=
1234567890ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
I: If#=0x5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
The purpose of each TTY is as follows:
* ttyUSB0: DIAG/QCDM port.
* ttyUSB1: GNSS data.
* ttyUSB2: AT-capable port (control).
* ttyUSB3: AT-capable port (data).
In the secondary layout with PID=0x9206 (AT+CUSBSELNV=86) the module
exposes 6 TTY ports:
T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=02(commc) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1e0e ProdID=9206 Rev=00.00
S: Manufacturer=SimTech, Incorporated
S: Product=SimTech SIM7080
S: SerialNumber=
1234567890ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
The purpose of each TTY is as follows:
* ttyUSB0: DIAG/QCDM port.
* ttyUSB1: GNSS data.
* ttyUSB2: AT-capable port (control).
* ttyUSB3: QFLOG interface.
* ttyUSB4: DAM interface.
* ttyUSB5: AT-capable port (data).
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patrick Riphagen [Thu, 6 Aug 2020 11:55:47 +0000 (13:55 +0200)]
USB: serial: ftdi_sio: add IDs for Xsens Mti USB converter
commit
6ccc48e0eb2f3a5f3bd39954a21317e5f8874726 upstream.
The device added has an FTDI chip inside.
The device is used to connect Xsens USB Motion Trackers.
Cc: stable@vger.kernel.org
Signed-off-by: Patrick Riphagen <patrick.riphagen@xsens.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zeng Tao [Fri, 4 Sep 2020 06:37:44 +0000 (14:37 +0800)]
usb: core: fix slab-out-of-bounds Read in read_descriptors
commit
a18cd6c9b6bc73dc17e8b7e9bd07decaa8833c97 upstream.
The USB device descriptor may get changed between two consecutive
enumerations on the same device for some reason, such as DFU or
malicius device.
In that case, we may access the changing descriptor if we don't take
the device lock here.
The issue is reported:
https://syzkaller.appspot.com/bug?id=
901a0d9e6519ef8dc7acab25344bd287dd3c7be9
Cc: stable <stable@vger.kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+256e56ddde8b8957eabd@syzkaller.appspotmail.com
Fixes:
217a9081d8e6 ("USB: add all configs to the "descriptors" attribute")
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Link: https://lore.kernel.org/r/1599201467-11000-1-git-send-email-prime.zeng@hisilicon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vaibhav Agarwal [Fri, 14 Aug 2020 12:33:15 +0000 (18:03 +0530)]
staging: greybus: audio: fix uninitialized value issue
commit
1dffeb8b8b4c261c45416d53c75ea51e6ece1770 upstream.
The current implementation for gbcodec_mixer_dapm_ctl_put() uses
uninitialized gbvalue for comparison with updated value. This was found
using static analysis with coverity.
Uninitialized scalar variable (UNINIT)
11. uninit_use: Using uninitialized value
gbvalue.value.integer_value[0].
460 if (gbvalue.value.integer_value[0] != val) {
This patch fixes the issue with fetching the gbvalue before using it for
comparision.
Fixes:
6339d2322c47 ("greybus: audio: Add topology parser for GB codec")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vaibhav Agarwal <vaibhav.sr@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/bc4f29eb502ccf93cd2ffd98db0e319fa7d0f247.1597408126.git.vaibhav.sr@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tetsuo Handa [Mon, 31 Aug 2020 10:37:00 +0000 (19:37 +0900)]
video: fbdev: fix OOB read in vga_8planes_imageblit()
commit
bd018a6a75cebb511bb55a0e7690024be975fe93 upstream.
syzbot is reporting OOB read at vga_8planes_imageblit() [1], for
"cdat[y] >> 4" can become a negative value due to "const char *cdat".
[1] https://syzkaller.appspot.com/bug?id=
0d7a0da1557dcd1989e00cb3692b26d4173b4132
Reported-by: syzbot <syzbot+69fbd3e01470f169c8c4@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/90b55ec3-d5b0-3307-9f7c-7ff5c5fd6ad3@i-love.sakura.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wanpeng Li [Wed, 19 Aug 2020 08:55:27 +0000 (16:55 +0800)]
KVM: VMX: Don't freeze guest when event delivery causes an APIC-access exit
commit
99b82a1437cb31340dbb2c437a2923b9814a7b15 upstream.
According to SDM 27.2.4, Event delivery causes an APIC-access VM exit.
Don't report internal error and freeze guest when event delivery causes
an APIC-access exit, it is handleable and the event will be re-injected
during the next vmentry.
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <
1597827327-25055-2-git-send-email-wanpengli@tencent.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Wed, 9 Sep 2020 21:53:50 +0000 (14:53 -0700)]
vgacon: remove software scrollback support
commit
973c096f6a85e5b5f2a295126ba6928d9a6afd45 upstream.
Yunhai Zhang recently fixed a VGA software scrollback bug in commit
ebfdfeeae8c0 ("vgacon: Fix for missing check in scrollback handling"),
but that then made people look more closely at some of this code, and
there were more problems on the vgacon side, but also the fbcon software
scrollback.
We don't really have anybody who maintains this code - probably because
nobody actually _uses_ it any more. Sure, people still use both VGA and
the framebuffer consoles, but they are no longer the main user
interfaces to the kernel, and haven't been for decades, so these kinds
of extra features end up bitrotting and not really being used.
So rather than try to maintain a likely unused set of code, I'll just
aggressively remove it, and see if anybody even notices. Maybe there
are people who haven't jumped on the whole GUI badnwagon yet, and think
it's just a fad. And maybe those people use the scrollback code.
If that turns out to be the case, we can resurrect this again, once
we've found the sucker^Wmaintainer for it who actually uses it.
Reported-by: NopNop Nop <nopitydays@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Cc: 张云海 <zhangyunhai@nsfocus.com>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Willy Tarreau <w@1wt.eu>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Tue, 8 Sep 2020 17:56:27 +0000 (10:56 -0700)]
fbcon: remove now unusued 'softback_lines' cursor() argument
commit
06a0df4d1b8b13b551668e47b11fd7629033b7df upstream.
Since the softscroll code got removed, this argument is always zero and
makes no sense any more.
Tested-by: Yuan Ming <yuanmingbuaa@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / GitHub / LineageOS / G12 / android_kernel_amlogic_linux-4.9.git / log