[ARM] 3201/1: PXA27x: Prevent hangup during resume due to inadvertedly enabling MBREQ (replaces: 3198/1)

Patch from Lothar Wassmann

The patch makes sure, that the ouptut functions of pins are restored
before restoring the Alternat Function settings, preventing pins from
being intermediately configured for undefined or unwanted alternate
functions.

Here is the original comment:
I've got a PXA270 system that uses GPIO80 as nCS4. This system did
hang on resume. Digging into the problem I found that the processor
stalled immediately when restoring the GAFR2_U register which restored
the alternate function for GPIO80. Since the GPDR registers were
restored after the GAFR registers, the offending GPIO was configured
as input at this point.
Thus the alternate function that was in effect after restoring the
GAFR was in fact the input function "MBREQ" instead of the output
function "nCS4". The "PXA27x Processor Family Developer's Manual"
(Footnote in Table 6-1 on page 6-3) states that:
"The MBREQ alternate function must not be enabled until the PSSR[RDH]
bit field is cleared. For more details, see Table 3-15, "PSSR Bit
Definitions" on page 3-71."

There is another note in the Developer's Manual (chapter 24.4.2
"GPIO operation as Alternate Function" on page 24-4)
stating that:
"Configuring a GPIO for an alternate function that is not defined for
it causes unpredictable results."

Since some GPIOs have no input function defined, and to prevent
inadvertedly programming the MBREQ function on some pin, the GAFR
registers should be restored after the GPDR registers have been
restored.

Additional provisions have to be made when the MBREQ function is
actually required. The corresponding GAFR bits should not be restored
with the regular GAFR restore, but must be set only after the PSSR
bits have been cleared.

Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 3200/1: Singlestep over ARM BX and BLX instructions using ptrace fix

Patch from Nikola Valerjev

Single stepping an application using ptrace() fails over ARM instructions BX and BLX.

Steps to reproduce:

Compile and link the following files

main.c
-----
void foo();
int main() {
    foo();
    return 0;
}

foo.s
-----
.text
.globl foo
foo:
BX LR

Using ptrace() functionality, run to main(), and start singlestepping.
Singlestep over \"BX LR\" instruction won\'t transfer the control back
to main, but run the code to completion.

This problems seems to be in the function get_branch_address() in
arch/arm/kernel/ptrace.c. The function doesn\'t seem to recognize BX
and BLX instructions as branches. BX and BLX instructions can be used
to convert from ARM to Thumb mode if the target address has the low
bit set. However, they are also perfectly legal in the ARM only mode.
Although other things in the kernel seem to indicate that only ARM
mode is accepted (and not Thumb), many compilers will generate BX
and BLX instructions even when generating ARM only code.

Signed-off-by: Nikola Valerjev <nikola@ghs.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 3199/1: Remove bogus function prototype from arch-pxa/irq.h

Patch from Deepak Saxena

This looks like a leftover from 2.4 days...

Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 3194/1: add pfn_to_kaddr macro for ARM take2

Patch from Hiroki Kaminaga

This patch defines a new macro: pfn_to_kaddr(pfn).
Same macro is already defined on other arch, such as i386.

Signed-off-by: Hiroki Kaminaga <kaminaga@sm.sony.co.jp>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 3191/1: Mark I/O pointer as const in __raw_reads[bwl]

Patch from Deepak Saxena

Mark the ioremap'd cookie/pointer in said functions as const since
we should not be actualy touching the data. This fixes a slew of
compile warnings on IXP4xx as our reads[bwl] already mark this
parameter as const.

Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM SMP] mpcore_wdt bogus fpos check

drivers/char/watchdog/mpcore_wdt.c write function contains a check for
(ppos != &file->f_pos). Such check used to make sense when a pointer to
file->f_pos was handed by vfs_write(), not a copy of it as it stands
now.

Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] Add memory.txt to 00-INDEX

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Linux v2.6.15-rc5

Hey, for no other reason than the fact that I'll be off-line for a
week.

Of course, I could force everybody to just use git (and when I'm emperor
of the world, don't think I won't!), but it seems some people want to
just test official releases.  Even if they are just -rc's.

By the time I'm back, Andrew will have fixed all my bugs, and I'll
release it as 2.6.15 and take all the credit.

Mwahahahaaa

Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Link USB drivers later in the kernel

We want to link the "regular" SCSI drivers before the USB storage
driver, since historically we've always detected internal SCSI disks
before the external USB storage modules.

The link order matters for initcall ordering, and this got broken by
mistake by commit 7586269c0b52970f60bb69fcb86e765fc1d72309 which moved
the USB host controller PCI quirk handling around.

Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Make vm_insert_page() available to NVidia module

It used to use remap_pfn_range(), which wasn't GPL-only either, and the
new interface is actually simpler and does more checking, so we
shouldn't unnecessarily discourage people from switching over.

Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] Fix up per-cpu page batch sizes

The code to clamp batch sizes to 2^n - 1 went missing and an extra
check got added, which must have been a hunk of the "higer order pcp
batch refills" work sneaking in.

Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] libata: fix ata_scsi_pass_thru error handling

This patch makes ata_scsi_pass_thru() properly set result code and
sense data on translation failures.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

NFSv4: Fix an Oops in the synchronous write path

 - Missing initialisation of attribute bitmask in _nfs4_proc_write()
 - On success, _nfs4_proc_write() must return number of bytes written.
 - Missing post_op_update_inode() in _nfs4_proc_write()
 - Missing initialisation of attribute bitmask in _nfs4_proc_commit()
 - Missing post_op_update_inode() in _nfs4_proc_commit()

Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

NFS: Fix post-op attribute revalidation...

  - Missing nfs_mark_for_revalidate in nfs_proc_link()
  - Missing nfs_mark_for_revalidate in nfs_rename()

Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

NFS: use set_page_writeback() in the appropriate places

 Ensure that we use set_page_writeback() in the appropriate places
 to help the VM in keeping its page radix_tree in sync.

Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

SUNRPC: Fix Oopsable condition in rpc_pipefs

 The elements on rpci->in_upcall are tracked by the filp->private_data,
 which will ensure that they get released when the file is closed.

 The exception is if rpc_close_pipes() gets called first, since that
 sets rpci->ops to NULL.

Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

NFS: Fix a few further cache consistency regressions

 Steve Dickson writes:
 Doing the following:
 1. On server:
 $ mkdir ~/t
 $ echo Hello > ~/t/tmp

 2. On client, wait for a string to appear in this file:
 $ until grep -q foo t/tmp ; do echo -n . ; sleep 1 ; done

 3. On server, create a *new* file with the same name containing that
 string:
 $ mv ~/t/tmp ~/t/tmp.old; echo foo > ~/t/tmp

 will show how the client will never (and I mean never ;-) ) see
 the updated file.

 The problem is that we do not update nfsi->cache_change_attribute when the
 file changes on the server (we only update it when our client makes the
 changes). This again means that functions like nfs_check_verifier() will
 fail to register when the parent directory has changed and should trigger
 a dentry lookup revalidation.

Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

NFS: Fix cache consistency regression

 Make sure cache_change_attribute is initialized to jiffies
 so when the mtime changes on directory, the directory
 will be refreshed.

 Signed-off by: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

Merge /pub/scm/linux/kernel/git/davem/net-2.6

Add missing "local_irq_enable()" to C2/C3 exit logic

Silly bug crept in with the C2/C3 TIF_POLLING_NRFLAG fixes.

Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[IPV6]: Load protocol module dynamically.

[ Modified to match inet_create() bug fix by Herbert Xu -DaveM ]

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

[IPV4] Fix EPROTONOSUPPORT error in inet_create

There is a coding error in inet_create that causes it to always return
ESOCKTNOSUPPORT.  It should return EPROTONOSUPPORT when there are
protocols registered for a given socket type but none of them match
the requested protocol.

This is based on a patch by Jayachandran C.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

[IGMP]: workaround for IGMP v1/v2 bug

From: David Stevens <dlstevens@us.ibm.com>

As explained at:

http://www.cs.ucsb.edu/~krishna/igmp_dos/

With IGMP version 1 and 2 it is possible to inject a unicast
report to a client which will make it ignore multicast
reports sent later by the router.

The fix is to only accept the report if is was sent to a
multicast or unicast address.

Signed-off-by: David S. Miller <davem@davemloft.net>

[SCTP]: Fix getsockname for sctp when an ipv6 socket accepts a connection from
an ipv4 socket.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[SCTP]: Return socket errors only if the receive queue is empty.

This patch fixes an issue where it is possible to get valid data after
a ENOTCONN error. It returns socket errors only after data queued on
socket receive queue is consumed.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Revert "[SCSI] fix usb storage oops"

This reverts commit 34ea80ec6a02ad02e6b9c75c478c18e5880d6713.

It does a put_device() from softirq context, which is bad since it gets
a semaphore for reading.

Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Merge /linux/kernel/git/jejb/scsi-rc-fixes-2.6

[PATCH] Fix TIF_POLLING_NRFLAG in ACPI idle routines

Commit 64c7c8f88559624abdbe12b5da6502e8879f8d28 broke the ACPI C2 and C3
sleep states, because it left TIF_POLLING_NRFLAG active even though
those states do not actually poll the reschedule flag at all.  As a
result, the CPU wouldn't get sent an IPI when it was to be woken up, and
would only notice that it had runnable processes on the next timer tick.

Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[SCSI] sg: fix a bug in st_map_user_pages failure path

sg's st_map_user_pages is modelled on an earlier version of st's
sgl_map_user_pages, and has the same bug: if get_user_pages got some but
not all of the pages, then those got were released, but the positive res
code returned implied that they were still to be freed.

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] sg and st unmap_user_pages allow PageReserved

2.6.15-rc1 made sg's st_unmap_user_pages and st's sgl_unmap_user_pages
BUG on a PageReserved page.  But that's wrong: they could be unmapping
the ZERO_PAGE, which is marked PG_reserved; and perhaps others (while
get_user_pages is still permitted on VM_PFNMAP areas - that may change).

More change is needed here: sg claims to dirty even pages written from,
and st claims not to dirty even pages read into; and SetPageDirty is not
adequate for this nowadays.  Fixes to those follow in a later patch: for
the moment just fix the 2.6.15 regression.

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Merge /pub/scm/linux/kernel/git/davem/net-2.6

Merge master.kernel.org:/home/rmk/linux-2.6-arm

Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus

Merge branch 'for-linus' of git://git./linux/kernel/git/roland/infiniband

Merge branch 'upstream-fixes' of /linux/kernel/git/jgarzik/netdev-2.6

[PATCH] V4l/dvb: Fix typo, removing incorrect info from CONFIG_BT848_DVB kconfig entry.

Fix typo, removing incorrect info from CONFIG_BT848_DVB kconfig entry.

Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] V4l/dvb: Restore missing tuner definition for Hauppauge tuner type 0x103

Type 0x103 ("TCL MFNM05-4") in the Hauppauge eeprom is a more recent tuner
that maps to TUNER_PHILIPS_FM1236_MK3.  This had been previously defined but
due to some accident the definition got removed.  This change restores that
definition.  Change committed on advice from Hans Verkuil
<hverkuil@xs4all.nl>, who thinks he's the one who had accidentally removed it
before.

Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] V4L/dvb: fix kernel message (print of %s from random pointer)

Fix kernel message ( basically printk("%s", random_pointer) ).

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] V4L/DVB: SCM update

Add v4l/dvb quilt tree to MAINTAINERS file.

Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] DVB: BUDGET CI card depends on STV0297 demodulator.

BUDGET_CI card depends on STV0297 demodulator.

Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] DVB: Fixes ifs in ves1820 set symbolrate().

Remove stray semicolons after if (foo); in ves1820_set_symbolrate().

Signed-off-by: Denis Vlasenko <vda@ilport.com.ua>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] DVB: Fix locking to prevent Oops on SMP systems

Fix locking to prevent Oops on SMP systems when starting/stopping dvb network
interfaces.

Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] DVB: Update Steve's email address.

Update Steve's email address.

Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] DVB: Small cleanups and CodeStyle fixes

- Small cleanups:

- make needlessly global functions static

- every file should #include the headers containing the prototypes for it's
  global functions

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] DVB: Include fixes for 2.6.15-rc1 for removing sched.h from module.h

Include fixes for 2.6.15-rc1 for removing sched.h from module.h.

Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] DVB: Fixed incorrect usage at the private state of the dvb-usb-devices

Fixed mistake of an incorrect usage of pid_filter-callbacks inside the private
state of the dvb-usb-devices

Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] DVB: Fix locking problems and code cleanup

Fix locking problems and code cleanup

Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] DVB: Fixed DiSEqC timing for saa7146-based budget cards

Fixed DiSEqC timing for saa7146-based budget cards (speed-up ioctls using
SAA7146_I2C_SHORT_DELAY)

Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] V4L: Add workaround for Hauppauge PVR150 with certain NTSC tuner models

Add workaround for Hauppauge PVR150 hardware problem with tuner models 85, 99
and 112 (model numbers as reported by tveeprom).  The audio standard
autodetection does not always work correctly for these models.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] V4L: Fixed eeprom handling for cx88 and added Nova-T PCI model 90003

- Fixed code handling for eeprom on cx88 boards.

- Hauppauge released a new version of the Nova-T-PCI (9002) a few months ago
  with a different (compatible) tuner (but lacking RF passthru).  The official
  model# is 90003.  All features are working.

- Adding entry to the known model list after testing.

Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] V4L: Fix bttv ioctls VIDIOC_ENUMINPUT, VIDIOCGTUNER, VIDIOC_QUERYCAP

Fixed bttv ioctls VIDIOC_ENUMINPUT, VIDIOCGTUNER, VIDIOC_QUERYCAP.

Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Michael H. Schimek <mschimek@gmx.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] V4L: Fix crash when not compiled as module

Fix crash when not compiled as module.

Signed-off-by: Reimar Doeffinger <Reimar.Doeffinger@stud.uni-karlsruhe.de>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] V4L: Write cached value to correct register for SECAM

Write cached value to correct register for SECAM.

Signed-off-by: Dwaine Garden <DwaineGarden@rogers.com>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] V4L: Fixes Bttv raw format to fix VIDIOCSPICT ioctl

Fixes Bttv raw format to fix VIDIOCSPICT ioctl.

Signed-off-by: Michael H. Schimek <mschimek@gmx.at>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] V4L: Makes needlessly global code static

This patch makes needlessly global code static.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] V4L: Some funcions now static and I2C hw code for IR

- Some funcions are now declared as static
- Added a I2C code for InfraRed.

Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] V4L: Enables audio DMA setting on cx88 chips, even when dma not in use

- Enabled audio DMA transfer code even when DMA not in use to solve a
  problem on some broken cx88 chips.

Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] V4L: Bttv bytes per line fix

bttv bytes per line fix.

Signed-off-by: Michael H. Schimek <mschimek@gmx.at>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] V4L: Fix read() bugs in bttv driver

Fix read() bugs in bttv driver.

Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Michael H. Schimek <mschimek@gmx.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] V4L: Removed audio DMA enabling from cx88-core

- Removed code that enables audio DMA transfers at cx88-core.
- This stuff should be at cx88-alsa when ready.

Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] V4L: Fixes nicam sound

- Resolved problem of sporadic buzz after setting Nicam stereo
- improved setting audio standard with dma reset
- cleaned up comments format
- more sensitive Nicam detection

Signed-off-by: Ian Pickworth <ian@pickworth.me.uk>
Signed-off-by: Michal Pytasz <pytasz@lodz.home.pl>
Signed-off-by: Marcin Rudowski <mar_rud@poczta.onet.pl>
Signed-off-by: Torsten Seeboth <Torsten.Seeboth@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] V4L: tveeprom MAC address parsing/cleanup

- Added a mac address field to the tveeprom structure.

- allow callers to query the MAC address.

- removed some redundant eeprom parsing code in cx88-cards.c (specific to
  Hauppauge DVB products) Instead, placed calls directly to the single eeprom
  parsing function in tveeprom.c

Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] V4: Include comments for DVB models and includes missing ones

Include comments for DVB models and includes missing ones

Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] V4L: Fixes warning at bttv-driver.c

Fixes warning at bttv-driver.c

Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] V4L: Fix hotplugging issues with saa7134

- Fixed issue with hotplugging and DMA sound (sound was lost when replugging
  a card)

- Added notifiers to main saa7134 module to let the sound sub-modules know
  when a card has been inserted or removed

Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] V4L: Fixes maximum number of VBI devices

- Increases the minor number limitation for vbi devices from 223 to 255.
  This is in agreement with the minor number allocation specified in
  Documentation/devices.txt.

- Without this patch it is not possible to use more than 5 Hauppauge
  WinTV-PVR 350 cards since each of these allocate 3 vbi devices.

Signed-of-by: Sigmund Augdal Helberg <sigmund@snap.tv>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] Keys: Fix permissions check for update vs add

Permit add_key() to once again update a matching key rather than adding a
new one if a matching key already exists in the target keyring.

This bug causes add_key() to always add a new key, displacing the old from
the target keyring.

Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] ppc32: fix treeboot image entrypoint

Correctly specify treeboot based image entrypoint.  Currently makefile uses
$(ENTRYPOINT) which isn't defined anywhere.  Each board port sets
entrypoint-$(CONFIG_BOARD_NAME) instead.

Without this patch I cannot boot Ocotea (PPC440GX eval board) anymore.  I
was getting random "OS panic" errors from OpenBIOS for a while, but with
current kernel I get them all the time (probably because image became
bigger).

Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Acked-by: Tom Rini <trini@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] ppc32: Fix incorrect PCI frequency value

The time to wait after deasserting PCI_RST has been counted with incorrect
value - this patch fixes the issue.

Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Merge branch 'release' of git://git./linux/kernel/git/lenb/linux-acpi-2.6

[NETLINK]: Fix processing of fib_lookup netlink messages

The receive path for fib_lookup netlink messages is lacking sanity
checks for header and payload and is thus vulnerable to malformed
netlink messages causing illegal memory references.

Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

[NETFILTER]: Fix recent match jiffies wrap mismatches

Around jiffies wrap time (i.e. within first 5 mins after boot), recent
match rules which contain both --seconds and --hitcount arguments
experience false matches.

This is because the last_pkts array is filled with zeros on creation, and
when comparing 'now' to 0 (+ --seconds argument), time_before_eq thinks it
has found a hit.

Below patch adds a break if the packet value is zero.  This has the
unfortunate side effect of causing mismatches if a packet was received
when jiffies really was equal to zero.  The odds of that happening are
slim compared to the problems caused by not adding the break however.
Plus, the author used this same method just below, so it is "good enough".

This fixes netfilter bugs #383 and #395.

Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

[NETFILTER]: Ignore ACKs ACKs on half open connections in TCP conntrack

Mounting NFS file systems after a (warm) reboot could take a long time if
firewalling and connection tracking was enabled.

The reason is that the NFS clients tends to use the same ports (800 and
counting down). Now on reboot, the server would still have a TCB for an
existing TCP connection client:800 -> server:2049. The client sends a
SYN from port 800 to server:2049, which elicits an ACK from the server.
The firewall on the client drops the ACK because (from its point of
view) the connection is still in half-open state, and it expects to see
a SYNACK.

The client will eventually time out after several minutes.

The following patch corrects this, by accepting ACKs on half open
connections as well.

Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

[SCSI] st: fix a bug in sgl_map_user_pages failure path

Nick and I had already been looking at drivers/scsi/{sg.c,st.c},
brought there by __put_page in sg.c's peculiar sg_rb_correct4mmap,
which we'd like to remove.  But that's irrelevant to your pain, except...

One extract from the patches I'd like to send Doug and Kai for 2.6.15
or 2.6.16 is this below: since the incomplete get_user_pages path omits
to reset res, but has already released all the pages, it will result in
premature freeing of user pages, and behaviour just like you've seen.

Though I'd have thought incomplete get_user_pages was an exceptional
case, and a bit surprised you'd encounter it.  Perhaps there's some
other premature freeing in the driver, and this instance has nothing
whatever to do with it.

If the problem were easily reproducible, it'd be great if you could
try this patch; but I think you've said it's not :-(

Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] mptfusion: Add maintainers

Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] mptfusion : dv performance fix

Syncronization for Domain Validation workqueue and the initiation of the
alternate controller.  Its possible that dv could be terminated if the
workqueue on the 1st channel doesn complete in time before the 2nd channel
begins initialization.

Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] sym2: Disable IU and QAS negotiation

Enabling these features causes problems with some drives, so disable
them until they're debugged

Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] zfcp: fix return code of zfcp_scsi_slave_alloc

Change return code in slave_alloc to avoid irritating error message from
scsi_alloc_sdev() when scsi stack tries target scan.

Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] zfcp: fix link down handling during firmware update

Don't check link down payload in case of firmware update.

Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] zfcp: fix adapter initialization

Fixed various problems in opening sequence of adapters which was previously
changed with NPIV support:
o corrected handling when exchange port data function is not supported,
  otherwise adapters on z900 cannot be opened anymore
o corrected setup of timer for exchange port data if called from error
  recovery
o corrected check of return code of exchange config data

Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] zfcp: fix spinlock initialization

Move initialization of locks and lists to adapter allocation function.
Otherwise we might end up with some uninitialized locks, like e.g. the
erp locks which only will be inititialized if an error recovery thread
for an adapter will be started.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] aacraid: Check scsi_bios_ptabe return code

Received from Mark Salyzyn.

scsi_bios_ptable return value is not being checked in aac_biosparm.

Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] SPI DV: be more conservative about echo buffer usage

Some SCSI devices apparently get very confused if we try to use the
echo buffer on a non-DT negotiated bus (this mirrors the problems of
using PPR on non-LVD for some devices).  The fix is to be far more
conservative about when we use an echo buffer.  With this patch, we'll
now see what parameters are negotiated by the read only test, and only
look for an echo buffer if DT is negotiated.

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[ARM] sema_count() removal

sema_count() defined only for ARM but not used anywhere.

Signed-off-by: Arthur Othieno <a.othieno@bluewin.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 3188/1: Add missing i2c dependency for Akita

Patch from Richard Purdie

Akita requires inbuilt kernel i2c support for its GPIOs. Add this
requirement to Kconfig and update the defconfig to match.

Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] Fix IXDP425 setup bug

There is a typo in the ARM IXDP425 setup definition that mistakenly tries
to use UART1's IRQ for UART2's traffic.

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM SMP] Use event instructions for spinlocks

ARMv6K CPUs have SEV (send event) and WFE (wait for event) instructions
which allow the CPU clock to be suspended until another CPU issues a
SEV, rather than spinning on the lock wasting power.  Make use of these
instructions.

Note that WFE does not wait if an event has been sent since the last WFE
cleared the event status, so although it may look racy, the instruction
implementation ensures that these are dealt with.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[MIPS] Update defconfigs to reflect Kconfig changes.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Avoid duplicate do_syscall_trace calls on return from sigreturn.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Fix register handling in syscalls when debugging.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Alchemy: Set board type on initialization.

From Sergei Shtylylov <sshtylyov@ru.mvista.com>.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Alchemy: Fix BCSR accesses.

Fixes BCSR accesses in the board setup/reset code.  The registers are
actually 16-bit, and their addresses are different between DBAu1550 and
other DBAu1xx0 boards.

From Sergei Shtylylov <sshtylyov@ru.mvista.com>.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Fix return path of sysmips(MIPS_ATOMIC_SET, ...)

The way we were doing things does no longer work on 2.6.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Qemu: Accept kernel command line passed by the Emulator.

From Daniel Jacobowitz <dan@debian.org>.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Qemu: Qemu is emulating a 1193.182kHz i8254 PIC.

From Daniel Jacobowitz <dan@debian.org>.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Generate SIGILL again

The rdhwr emulation accidentally swallowed the SIGILL from most other
illegal instructions.  Make sure to return -EFAULT by default.

Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Kconfig: Include init/Kconfig after we've set 32BIT / 64BIT.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Use reset_page_mapcount to initialize empty_zero_page usage counter.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] R10000 and R12000 need to set MIPS_CPU_4K_CACHE ...

... because they have R4000-style caches.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] JMR3927: Declare puts function.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>