Colin Ian King [Wed, 19 Jul 2017 17:46:59 +0000 (18:46 +0100)]
net: tehuti: don't process data if it has not been copied from userspace
The array data is only populated with valid information from userspace
if cmd != SIOCDEVPRIVATE, other cases the array contains garbage on
the stack. The subsequent switch statement acts on a subcommand in
data[0] which could be any garbage value if cmd is SIOCDEVPRIVATE which
seems incorrect to me. Instead, just return EOPNOTSUPP for the case
where cmd == SIOCDEVPRIVATE to avoid this issue.
As a side note, I suspect that the original intention of the code
was for this ioctl to work just for cmd == SIOCDEVPRIVATE (and the
current logic is reversed). However, I don't wont to change the current
semantics in case any userspace code relies on this existing behaviour.
Detected by CoverityScan, CID#139647 ("Uninitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 19 Jul 2017 17:22:40 +0000 (10:22 -0700)]
Revert "rtnetlink: Do not generate notifications for CHANGEADDR event"
This reverts commit
cd8966e75ed3c6b41a37047a904617bc44fa481f.
The duplicate CHANGEADDR event message is sent regardless of link
status whereas the setlink changes only generate a notification when
the link is up. Not sending a notification when the link is down breaks
dhcpcd which only processes hwaddr changes when the link is down.
Fixes reported regression:
https://bugzilla.kernel.org/show_bug.cgi?id=196355
Reported-by: Yaroslav Isakov <yaroslav.isakov@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Hundebøll [Wed, 19 Jul 2017 06:17:02 +0000 (08:17 +0200)]
net: dsa: mv88e6xxx: Enable CMODE config support for 6390X
Commit
f39908d3b1c45 ('net: dsa: mv88e6xxx: Set the CMODE for mv88e6390
ports 9 & 10') added support for setting the CMODE for the 6390X family,
but only enabled it for 9290 and 6390 - and left out 6390X.
Fix support for setting the CMODE on 6390X also by assigning
mv88e6390x_port_set_cmode() to the .port_set_cmode function pointer in
mv88e6390x_ops too.
Fixes:
f39908d3b1c4 ("net: dsa: mv88e6xxx: Set the CMODE for mv88e6390 ports 9 & 10")
Signed-off-by: Martin Hundebøll <mnhu@prevas.dk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arun Parameswaran [Thu, 6 Jul 2017 17:37:57 +0000 (10:37 -0700)]
dt-binding: ptp: Add SoC compatibility strings for dte ptp clock
Add SoC specific compatibility strings to the Broadcom DTE
based PTP clock binding document.
Fixed the document heading and node name.
Fixes:
80d6076140b2 ("dt-binding: ptp: add bindings document for dte based ptp clock")
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eugeniy Paltsev [Tue, 18 Jul 2017 14:07:15 +0000 (17:07 +0300)]
NET: dwmac: Make dwmac reset unconditional
Unconditional reset dwmac before HW init if reset controller is present.
In existing implementation we reset dwmac only after second module
probing:
(module load -> unload -> load again [reset happens])
Now we reset dwmac at every module load:
(module load [reset happens] -> unload -> load again [reset happens])
Also some reset controllers have only reset callback instead of
assert + deassert callbacks pair, so handle this case.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 19 Jul 2017 20:33:24 +0000 (13:33 -0700)]
net: Zero terminate ifr_name in dev_ifname().
The ifr.ifr_name is passed around and assumed to be NULL terminated.
Signed-off-by: David S. Miller <davem@davemloft.net>
Levin, Alexander [Tue, 18 Jul 2017 04:23:16 +0000 (04:23 +0000)]
wireless: wext: terminate ifr name coming from userspace
ifr name is assumed to be a valid string by the kernel, but nothing
was forcing username to pass a valid string.
In turn, this would cause panics as we tried to access the string
past it's valid memory.
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Tue, 18 Jul 2017 19:38:56 +0000 (22:38 +0300)]
netfilter: fix netfilter_net_init() return
We accidentally return an uninitialized variable.
Fixes:
cf56c2f892a8 ("netfilter: remove old pre-netns era hook api")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 18 Jul 2017 19:01:39 +0000 (12:01 -0700)]
Merge git://git./pub/scm/linux/kernel/git/pablo/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Missing netlink message sanity check in nfnetlink, patch from
Mateusz Jurczyk.
2) We now have netfilter per-netns hooks, so let's kill global hook
infrastructure, this infrastructure is known to be racy with netns.
We don't care about out of tree modules. Patch from Florian Westphal.
3) find_appropriate_src() is buggy when colissions happens after the
conversion of the nat bysource to rhashtable. Also from Florian.
4) Remove forward chain in nf_tables arp family, it's useless and it is
causing quite a bit of confusion, from Florian Westphal.
5) nf_ct_remove_expect() is called with the wrong parameter, causing
kernel oops, patch from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 18 Jul 2017 09:57:55 +0000 (11:57 +0200)]
udp: preserve skb->dst if required for IP options processing
Eric noticed that in udp_recvmsg() we still need to access
skb->dst while processing the IP options.
Since commit
0a463c78d25b ("udp: avoid a cache miss on dequeue")
skb->dst is no more available at recvmsg() time and bad things
will happen if we enter the relevant code path.
This commit address the issue, avoid clearing skb->dst if
any IP options are present into the relevant skb.
Since the IP CB is contained in the first skb cacheline, we can
test it to decide to leverage the consume_stateless_skb()
optimization, without measurable additional cost in the faster
path.
v1 -> v2: updated commit message tags
Fixes:
0a463c78d25b ("udp: avoid a cache miss on dequeue")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe Jaillet [Mon, 17 Jul 2017 17:42:41 +0000 (19:42 +0200)]
atm: zatm: Fix an error handling path in 'zatm_init_one()'
If 'dma_set_mask_and_coherent()' fails, we must undo the previous
'pci_request_regions()' call.
Adjust corresponding 'goto' to jump at the right place of the error
handling path.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Potapenko [Mon, 17 Jul 2017 10:35:58 +0000 (12:35 +0200)]
ipv4: ipv6: initialize treq->txhash in cookie_v[46]_check()
KMSAN reported use of uninitialized memory in skb_set_hash_from_sk(),
which originated from the TCP request socket created in
cookie_v6_check():
==================================================================
BUG: KMSAN: use of uninitialized memory in tcp_transmit_skb+0xf77/0x3ec0
CPU: 1 PID: 2949 Comm: syz-execprog Not tainted 4.11.0-rc5+ #2931
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
TCP: request_sock_TCPv6: Possible SYN flooding on port 20028. Sending cookies. Check SNMP counters.
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:16
dump_stack+0x172/0x1c0 lib/dump_stack.c:52
kmsan_report+0x12a/0x180 mm/kmsan/kmsan.c:927
__msan_warning_32+0x61/0xb0 mm/kmsan/kmsan_instr.c:469
skb_set_hash_from_sk ./include/net/sock.h:2011
tcp_transmit_skb+0xf77/0x3ec0 net/ipv4/tcp_output.c:983
tcp_send_ack+0x75b/0x830 net/ipv4/tcp_output.c:3493
tcp_delack_timer_handler+0x9a6/0xb90 net/ipv4/tcp_timer.c:284
tcp_delack_timer+0x1b0/0x310 net/ipv4/tcp_timer.c:309
call_timer_fn+0x240/0x520 kernel/time/timer.c:1268
expire_timers kernel/time/timer.c:1307
__run_timers+0xc13/0xf10 kernel/time/timer.c:1601
run_timer_softirq+0x36/0xa0 kernel/time/timer.c:1614
__do_softirq+0x485/0x942 kernel/softirq.c:284
invoke_softirq kernel/softirq.c:364
irq_exit+0x1fa/0x230 kernel/softirq.c:405
exiting_irq+0xe/0x10 ./arch/x86/include/asm/apic.h:657
smp_apic_timer_interrupt+0x5a/0x80 arch/x86/kernel/apic/apic.c:966
apic_timer_interrupt+0x86/0x90 arch/x86/entry/entry_64.S:489
RIP: 0010:native_restore_fl ./arch/x86/include/asm/irqflags.h:36
RIP: 0010:arch_local_irq_restore ./arch/x86/include/asm/irqflags.h:77
RIP: 0010:__msan_poison_alloca+0xed/0x120 mm/kmsan/kmsan_instr.c:440
RSP: 0018:
ffff880024917cd8 EFLAGS:
00000246 ORIG_RAX:
ffffffffffffff10
RAX:
0000000000000246 RBX:
ffff8800224c0000 RCX:
0000000000000005
RDX:
0000000000000004 RSI:
ffff880000000000 RDI:
ffffea0000b6d770
RBP:
ffff880024917d58 R08:
0000000000000dd8 R09:
0000000000000004
R10:
0000160000000000 R11:
0000000000000000 R12:
ffffffff85abf810
R13:
ffff880024917dd8 R14:
0000000000000010 R15:
ffffffff81cabde4
</IRQ>
poll_select_copy_remaining+0xac/0x6b0 fs/select.c:293
SYSC_select+0x4b4/0x4e0 fs/select.c:653
SyS_select+0x76/0xa0 fs/select.c:634
entry_SYSCALL_64_fastpath+0x13/0x94 arch/x86/entry/entry_64.S:204
RIP: 0033:0x4597e7
RSP: 002b:
000000c420037ee0 EFLAGS:
00000246 ORIG_RAX:
0000000000000017
RAX:
ffffffffffffffda RBX:
0000000000000000 RCX:
00000000004597e7
RDX:
0000000000000000 RSI:
0000000000000000 RDI:
0000000000000000
RBP:
000000c420037ef0 R08:
000000c420037ee0 R09:
0000000000000059
R10:
0000000000000000 R11:
0000000000000246 R12:
000000000042dc20
R13:
00000000000000f3 R14:
0000000000000030 R15:
0000000000000003
chained origin:
save_stack_trace+0x37/0x40 arch/x86/kernel/stacktrace.c:59
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:302
kmsan_save_stack mm/kmsan/kmsan.c:317
kmsan_internal_chain_origin+0x12a/0x1f0 mm/kmsan/kmsan.c:547
__msan_store_shadow_origin_4+0xac/0x110 mm/kmsan/kmsan_instr.c:259
tcp_create_openreq_child+0x709/0x1ae0 net/ipv4/tcp_minisocks.c:472
tcp_v6_syn_recv_sock+0x7eb/0x2a30 net/ipv6/tcp_ipv6.c:1103
tcp_get_cookie_sock+0x136/0x5f0 net/ipv4/syncookies.c:212
cookie_v6_check+0x17a9/0x1b50 net/ipv6/syncookies.c:245
tcp_v6_cookie_check net/ipv6/tcp_ipv6.c:989
tcp_v6_do_rcv+0xdd8/0x1c60 net/ipv6/tcp_ipv6.c:1298
tcp_v6_rcv+0x41a3/0x4f00 net/ipv6/tcp_ipv6.c:1487
ip6_input_finish+0x82f/0x1ee0 net/ipv6/ip6_input.c:279
NF_HOOK ./include/linux/netfilter.h:257
ip6_input+0x239/0x290 net/ipv6/ip6_input.c:322
dst_input ./include/net/dst.h:492
ip6_rcv_finish net/ipv6/ip6_input.c:69
NF_HOOK ./include/linux/netfilter.h:257
ipv6_rcv+0x1dbd/0x22e0 net/ipv6/ip6_input.c:203
__netif_receive_skb_core+0x2f6f/0x3a20 net/core/dev.c:4208
__netif_receive_skb net/core/dev.c:4246
process_backlog+0x667/0xba0 net/core/dev.c:4866
napi_poll net/core/dev.c:5268
net_rx_action+0xc95/0x1590 net/core/dev.c:5333
__do_softirq+0x485/0x942 kernel/softirq.c:284
origin:
save_stack_trace+0x37/0x40 arch/x86/kernel/stacktrace.c:59
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:302
kmsan_internal_poison_shadow+0xb1/0x1a0 mm/kmsan/kmsan.c:198
kmsan_kmalloc+0x7f/0xe0 mm/kmsan/kmsan.c:337
kmem_cache_alloc+0x1c2/0x1e0 mm/slub.c:2766
reqsk_alloc ./include/net/request_sock.h:87
inet_reqsk_alloc+0xa4/0x5b0 net/ipv4/tcp_input.c:6200
cookie_v6_check+0x4f4/0x1b50 net/ipv6/syncookies.c:169
tcp_v6_cookie_check net/ipv6/tcp_ipv6.c:989
tcp_v6_do_rcv+0xdd8/0x1c60 net/ipv6/tcp_ipv6.c:1298
tcp_v6_rcv+0x41a3/0x4f00 net/ipv6/tcp_ipv6.c:1487
ip6_input_finish+0x82f/0x1ee0 net/ipv6/ip6_input.c:279
NF_HOOK ./include/linux/netfilter.h:257
ip6_input+0x239/0x290 net/ipv6/ip6_input.c:322
dst_input ./include/net/dst.h:492
ip6_rcv_finish net/ipv6/ip6_input.c:69
NF_HOOK ./include/linux/netfilter.h:257
ipv6_rcv+0x1dbd/0x22e0 net/ipv6/ip6_input.c:203
__netif_receive_skb_core+0x2f6f/0x3a20 net/core/dev.c:4208
__netif_receive_skb net/core/dev.c:4246
process_backlog+0x667/0xba0 net/core/dev.c:4866
napi_poll net/core/dev.c:5268
net_rx_action+0xc95/0x1590 net/core/dev.c:5333
__do_softirq+0x485/0x942 kernel/softirq.c:284
==================================================================
Similar error is reported for cookie_v4_check().
Fixes:
58d607d3e52f ("tcp: provide skb->hash to synack packets")
Signed-off-by: Alexander Potapenko <glider@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gao Feng [Mon, 17 Jul 2017 10:34:42 +0000 (18:34 +0800)]
ppp: Fix false xmit recursion detect with two ppp devices
The global percpu variable ppp_xmit_recursion is used to detect the ppp
xmit recursion to avoid the deadlock, which is caused by one CPU tries to
lock the xmit lock twice. But it would report false recursion when one CPU
wants to send the skb from two different PPP devices, like one L2TP on the
PPPoE. It is a normal case actually.
Now use one percpu member of struct ppp instead of the gloable variable to
detect the xmit recursion of one ppp device.
Fixes:
55454a565836 ("ppp: avoid dealock on recursive xmit")
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: Liu Jianying <jianying.liu@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Mon, 17 Jul 2017 18:42:55 +0000 (11:42 -0700)]
bpf: check NULL for sk_to_full_sk() return value
When req->rsk_listener is NULL, sk_to_full_sk() returns
NULL too, so we have to check its return value against
NULL here.
Fixes:
40304b2a1567 ("bpf: BPF support for sock_ops")
Reported-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Cc: Lawrence Brakmo <brakmo@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Sat, 15 Jul 2017 06:03:49 +0000 (23:03 -0700)]
jhash: fix -Wimplicit-fallthrough warnings
GCC 7 added a new -Wimplicit-fallthrough warning. It's only enabled
with W=1, but since linux/jhash.h is included in over hundred places
(including other global headers) it seems worthwhile fixing this
warning.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Mon, 10 Jul 2017 11:53:53 +0000 (13:53 +0200)]
netfilter: expect: fix crash when putting uninited expectation
We crash in __nf_ct_expect_check, it calls nf_ct_remove_expect on the
uninitialised expectation instead of existing one, so del_timer chokes
on random memory address.
Fixes:
ec0e3f01114ad32711243 ("netfilter: nf_ct_expect: Add nf_ct_remove_expect()")
Reported-by: Sergey Kvachonok <ravenexp@gmail.com>
Tested-by: Sergey Kvachonok <ravenexp@gmail.com>
Cc: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Florian Westphal [Fri, 7 Jul 2017 11:29:03 +0000 (13:29 +0200)]
netfilter: nf_tables: only allow in/output for arp packets
arp packets cannot be forwarded.
They can be bridged, but then they can be filtered using
either ebtables or nftables bridge family.
The bridge netfilter exposes a "call-arptables" switch which
pushes packets into arptables, but lets not expose this for nftables, so better
close this asap.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Florian Westphal [Fri, 7 Jul 2017 11:07:17 +0000 (13:07 +0200)]
netfilter: nat: fix src map lookup
When doing initial conversion to rhashtable I replaced the bucket
walk with a single rhashtable_lookup_fast().
When moving to rhlist I failed to properly walk the list of identical
tuples, but that is what is needed for this to work correctly.
The table contains the original tuples, so the reply tuples are all
distinct.
We currently decide that mapping is (not) in range only based on the
first entry, but in case its not we need to try the reply tuple of the
next entry until we either find an in-range mapping or we checked
all the entries.
This bug makes nat core attempt collision resolution while it might be
able to use the mapping as-is.
Fixes:
870190a9ec90 ("netfilter: nat: convert nat bysrc hash to rhashtable")
Reported-by: Jaco Kroon <jaco@uls.co.za>
Tested-by: Jaco Kroon <jaco@uls.co.za>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Florian Westphal [Thu, 6 Jul 2017 21:17:44 +0000 (23:17 +0200)]
netfilter: remove old pre-netns era hook api
no more users in the tree, remove this.
The old api is racy wrt. module removal, all users have been converted
to the netns-aware api.
The old api pretended we still have global hooks but that has not been
true for a long time.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Mateusz Jurczyk [Wed, 7 Jun 2017 13:50:38 +0000 (15:50 +0200)]
netfilter: nfnetlink: Improve input length sanitization in nfnetlink_rcv
Verify that the length of the socket buffer is sufficient to cover the
nlmsghdr structure before accessing the nlh->nlmsg_len field for further
input sanitization. If the client only supplies 1-3 bytes of data in
sk_buff, then nlh->nlmsg_len remains partially uninitialized and
contains leftover memory from the corresponding kernel allocation.
Operating on such data may result in indeterminate evaluation of the
nlmsg_len < NLMSG_HDRLEN expression.
The bug was discovered by a runtime instrumentation designed to detect
use of uninitialized memory in the kernel. The patch prevents this and
other similar tools (e.g. KMSAN) from flagging this behavior in the future.
Signed-off-by: Mateusz Jurczyk <mjurczyk@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
David S. Miller [Sun, 16 Jul 2017 04:29:08 +0000 (21:29 -0700)]
Merge branch 'bcmgenet-Fragmented-SKB-corrections'
Doug Berger says:
====================
bcmgenet: Fragmented SKB corrections
Two issues were observed in a review of the bcmgenet driver support for
fragmented SKBs which are addressed by this patch set.
The first addresses a problem that could occur if the driver is not able
to DMA map a fragment of the SKB. This would be a highly unusual event
but it would leave the hardware descriptors in an invalid state which
should be prevented.
The second is a hazard that could occur if the driver is able to reclaim
the first control block of a fragmented SKB before all of its fragments
have completed processing by the hardware. In this case the SKB could
be freed leading to reuse of memory that is still in use by hardware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Doug Berger [Fri, 14 Jul 2017 23:12:10 +0000 (16:12 -0700)]
net: bcmgenet: Free skb after last Tx frag
Since the skb is attached to the first control block of a fragmented
skb it is possible that the skb could be freed when reclaiming that
control block before all fragments of the skb have been consumed by
the hardware and unmapped.
This commit introduces first_cb and last_cb pointers to the skb
control block used by the driver to keep track of which transmit
control blocks within a transmit ring are the first and last ones
associated with the skb.
It then splits the bcmgenet_free_cb() function into transmit
(bcmgenet_free_tx_cb) and receive (bcmgenet_free_rx_cb) versions
that can handle the unmapping of dma mapped memory and cleaning up
the corresponding control block structure so that the skb is only
freed after the last associated transmit control block is reclaimed.
Fixes:
1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doug Berger [Fri, 14 Jul 2017 23:12:09 +0000 (16:12 -0700)]
net: bcmgenet: Fix unmapping of fragments in bcmgenet_xmit()
In case we fail to map a single fragment, we would be leaving the
transmit ring populated with stale entries.
This commit introduces the helper function bcmgenet_put_txcb()
which takes care of rewinding the per-ring write pointer back to
where we left.
It also consolidates the functionality of bcmgenet_xmit_single()
and bcmgenet_xmit_frag() into the bcmgenet_xmit() function to
make the unmapping of control blocks cleaner.
Fixes:
1c1008c793fa ("net: bcmgenet: add main driver file")
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Sat, 15 Jul 2017 17:24:47 +0000 (10:24 -0700)]
dt-bindings: net: Remove duplicate NSP Ethernet MAC binding document
Commit
07d4510f5251 ("dt-bindings: net: bgmac: add bindings documentation for
bgmac") added both brcm,amac-nsp.txt and brcm,bgmac-nsp.txt. The former is
actually the one that got updated and is in use by the bgmac driver while the
latter is duplicating the former and is not used nor updated.
Fixes:
07d4510f5251 ("dt-bindings: net: bgmac: add bindings documentation for bgmac")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 16 Jul 2017 04:25:57 +0000 (21:25 -0700)]
Merge branch 'isdn-const-pci_device_ids'
Arvind Yadav says:
====================
Constify isdn pci_device_id's.
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Arvind Yadav [Sat, 15 Jul 2017 04:25:51 +0000 (09:55 +0530)]
isdn: avm: c4: constify pci_device_id.
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
11803 544 1 12348 303c isdn/hardware/avm/c4.o
File size After adding 'const':
text data bss dec hex filename
11931 416 1 12348 303c isdn/hardware/avm/c4.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arvind Yadav [Sat, 15 Jul 2017 04:25:50 +0000 (09:55 +0530)]
isdn: mISDN: hfcpci: constify pci_device_id.
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
21656 1024 96 22776 58f8 isdn/hardware/mISDN/hfcpci.o
File size After adding 'const':
text data bss dec hex filename
22424 256 96 22776 58f8 isdn/hardware/mISDN/hfcpci.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arvind Yadav [Sat, 15 Jul 2017 04:25:49 +0000 (09:55 +0530)]
isdn: mISDN: avmfritz: constify pci_device_id.
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
9963 1936 16 11915 2e8b isdn/hardware/mISDN/avmfritz.o
File size After adding 'const':
text data bss dec hex filename
10091 1808 16 11915 2e8b isdn/hardware/mISDN/avmfritz.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arvind Yadav [Sat, 15 Jul 2017 04:25:48 +0000 (09:55 +0530)]
isdn: mISDN: w6692: constify pci_device_id.
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
13959 4080 24 18063 468f isdn/hardware/mISDN/w6692.o
File size After adding 'const':
text data bss dec hex filename
14087 3952 24 18063 468f isdn/hardware/mISDN/w6692.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arvind Yadav [Sat, 15 Jul 2017 04:25:47 +0000 (09:55 +0530)]
isdn: mISDN: hfcmulti: constify pci_device_id.
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
63450 1536 1492 66478 103ae isdn/hardware/mISDN/hfcmulti.o
File size After adding 'const':
text data bss dec hex filename
64698 288 1492 66478 103ae isdn/hardware/mISDN/hfcmulti.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arvind Yadav [Sat, 15 Jul 2017 04:25:46 +0000 (09:55 +0530)]
isdn: mISDN: netjet: constify pci_device_id.
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
10941 1776 16 12733 31bd isdn/hardware/mISDN/netjet.o
File size After adding 'const':
text data bss dec hex filename
11005 1712 16 12733 31bd isdn/hardware/mISDN/netjet.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arvind Yadav [Sat, 15 Jul 2017 04:25:45 +0000 (09:55 +0530)]
isdn: eicon: constify pci_device_id.
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
6224 655 8 6887 1ae7 isdn/hardware/eicon/divasmain.o
File size After adding 'const':
text data bss dec hex filename
6608 271 8 6887 1ae7 isdn/hardware/eicon/divasmain.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arvind Yadav [Sat, 15 Jul 2017 04:25:44 +0000 (09:55 +0530)]
isdn: hisax: hisax_fcpcipnp: constify pci_device_id.
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
5989 576 0 6565 19a5 isdn/hisax/hisax_fcpcipnp.o
File size After adding 'const':
text data bss dec hex filename
6085 480 0 6565 19a5 isdn/hisax/hisax_fcpcipnp.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arvind Yadav [Sat, 15 Jul 2017 04:25:43 +0000 (09:55 +0530)]
isdn: hisax: hfc4s8s_l1: constify pci_device_id.
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
10512 536 4 11052 2b2c drivers/isdn/hisax/hfc4s8s_l1.o
File size After adding 'const':
text data bss dec hex filename
10672 376 4 11052 2b2c drivers/isdn/hisax/hfc4s8s_l1.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arvind Yadav [Sat, 15 Jul 2017 04:25:42 +0000 (09:55 +0530)]
isdn: hisax: constify pci_device_id.
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
13686 2064 4416 20166 4ec6 drivers/isdn/hisax/config.o
File size After adding 'const':
text data bss dec hex filename
15030 720 4416 20166 4ec6 drivers/isdn/hisax/config.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neal Cardwell [Fri, 14 Jul 2017 21:49:25 +0000 (17:49 -0400)]
tcp_bbr: init pacing rate on first RTT sample
Fixes the following behavior: for connections that had no RTT sample
at the time of initializing congestion control, BBR was initializing
the pacing rate to a high nominal rate (based an a guess of RTT=1ms,
in case this is LAN traffic). Then BBR never adjusted the pacing rate
downward upon obtaining an actual RTT sample, if the connection never
filled the pipe (e.g. all sends were small app-limited writes()).
This fix adjusts the pacing rate upon obtaining the first RTT sample.
Fixes:
0f8782ea1497 ("tcp_bbr: add BBR congestion control")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neal Cardwell [Fri, 14 Jul 2017 21:49:24 +0000 (17:49 -0400)]
tcp_bbr: remove sk_pacing_rate=0 transient during init
Fix a corner case noticed by Eric Dumazet, where BBR's setting
sk->sk_pacing_rate to 0 during initialization could theoretically
cause packets in the sending host to hang if there were packets "in
flight" in the pacing infrastructure at the time the BBR congestion
control state is initialized. This could occur if the pacing
infrastructure happened to race with bbr_init() in a way such that the
pacer read the 0 rather than the immediately following non-zero pacing
rate.
Fixes:
0f8782ea1497 ("tcp_bbr: add BBR congestion control")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neal Cardwell [Fri, 14 Jul 2017 21:49:23 +0000 (17:49 -0400)]
tcp_bbr: introduce bbr_init_pacing_rate_from_rtt() helper
Introduce a helper to initialize the BBR pacing rate unconditionally,
based on the current cwnd and RTT estimate. This is a pure refactor,
but is needed for two following fixes.
Fixes:
0f8782ea1497 ("tcp_bbr: add BBR congestion control")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neal Cardwell [Fri, 14 Jul 2017 21:49:22 +0000 (17:49 -0400)]
tcp_bbr: introduce bbr_bw_to_pacing_rate() helper
Introduce a helper to convert a BBR bandwidth and gain factor to a
pacing rate in bytes per second. This is a pure refactor, but is
needed for two following fixes.
Fixes:
0f8782ea1497 ("tcp_bbr: add BBR congestion control")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neal Cardwell [Fri, 14 Jul 2017 21:49:21 +0000 (17:49 -0400)]
tcp_bbr: cut pacing rate only if filled pipe
In bbr_set_pacing_rate(), which decides whether to cut the pacing
rate, there was some code that considered exiting STARTUP to be
equivalent to the notion of filling the pipe (i.e.,
bbr_full_bw_reached()). Specifically, as the code was structured,
exiting STARTUP and going into PROBE_RTT could cause us to cut the
pacing rate down to something silly and low, based on whatever
bandwidth samples we've had so far, when it's possible that all of
them have been small app-limited bandwidth samples that are not
representative of the bandwidth available in the path. (The code was
correct at the time it was written, but the state machine changed
without this spot being adjusted correspondingly.)
Fixes:
0f8782ea1497 ("tcp_bbr: add BBR congestion control")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Rose [Fri, 14 Jul 2017 19:42:49 +0000 (12:42 -0700)]
openvswitch: Fix for force/commit action failures
When there is an established connection in direction A->B, it is
possible to receive a packet on port B which then executes
ct(commit,force) without first performing ct() - ie, a lookup.
In this case, we would expect that this packet can delete the existing
entry so that we can commit a connection with direction B->A. However,
currently we only perform a check in skb_nfct_cached() for whether
OVS_CS_F_TRACKED is set and OVS_CS_F_INVALID is not set, ie that a
lookup previously occurred. In the above scenario, a lookup has not
occurred but we should still be able to statelessly look up the
existing entry and potentially delete the entry if it is in the
opposite direction.
This patch extends the check to also hint that if the action has the
force flag set, then we will lookup the existing entry so that the
force check at the end of skb_nfct_cached has the ability to delete
the connection.
Fixes:
dd41d330b03 ("openvswitch: Add force commit.")
CC: Pravin Shelar <pshelar@nicira.com>
CC: dev@openvswitch.org
Signed-off-by: Joe Stringer <joe@ovn.org>
Signed-off-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Potapenko [Fri, 14 Jul 2017 16:32:45 +0000 (18:32 +0200)]
sctp: don't dereference ptr before leaving _sctp_walk_{params, errors}()
If the length field of the iterator (|pos.p| or |err|) is past the end
of the chunk, we shouldn't access it.
This bug has been detected by KMSAN. For the following pair of system
calls:
socket(PF_INET6, SOCK_STREAM, 0x84 /* IPPROTO_??? */) = 3
sendto(3, "A", 1, MSG_OOB, {sa_family=AF_INET6, sin6_port=htons(0),
inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=0,
sin6_scope_id=0}, 28) = 1
the tool has reported a use of uninitialized memory:
==================================================================
BUG: KMSAN: use of uninitialized memory in sctp_rcv+0x17b8/0x43b0
CPU: 1 PID: 2940 Comm: probe Not tainted 4.11.0-rc5+ #2926
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs
01/01/2011
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:16
dump_stack+0x172/0x1c0 lib/dump_stack.c:52
kmsan_report+0x12a/0x180 mm/kmsan/kmsan.c:927
__msan_warning_32+0x61/0xb0 mm/kmsan/kmsan_instr.c:469
__sctp_rcv_init_lookup net/sctp/input.c:1074
__sctp_rcv_lookup_harder net/sctp/input.c:1233
__sctp_rcv_lookup net/sctp/input.c:1255
sctp_rcv+0x17b8/0x43b0 net/sctp/input.c:170
sctp6_rcv+0x32/0x70 net/sctp/ipv6.c:984
ip6_input_finish+0x82f/0x1ee0 net/ipv6/ip6_input.c:279
NF_HOOK ./include/linux/netfilter.h:257
ip6_input+0x239/0x290 net/ipv6/ip6_input.c:322
dst_input ./include/net/dst.h:492
ip6_rcv_finish net/ipv6/ip6_input.c:69
NF_HOOK ./include/linux/netfilter.h:257
ipv6_rcv+0x1dbd/0x22e0 net/ipv6/ip6_input.c:203
__netif_receive_skb_core+0x2f6f/0x3a20 net/core/dev.c:4208
__netif_receive_skb net/core/dev.c:4246
process_backlog+0x667/0xba0 net/core/dev.c:4866
napi_poll net/core/dev.c:5268
net_rx_action+0xc95/0x1590 net/core/dev.c:5333
__do_softirq+0x485/0x942 kernel/softirq.c:284
do_softirq_own_stack+0x1c/0x30 arch/x86/entry/entry_64.S:902
</IRQ>
do_softirq kernel/softirq.c:328
__local_bh_enable_ip+0x25b/0x290 kernel/softirq.c:181
local_bh_enable+0x37/0x40 ./include/linux/bottom_half.h:31
rcu_read_unlock_bh ./include/linux/rcupdate.h:931
ip6_finish_output2+0x19b2/0x1cf0 net/ipv6/ip6_output.c:124
ip6_finish_output+0x764/0x970 net/ipv6/ip6_output.c:149
NF_HOOK_COND ./include/linux/netfilter.h:246
ip6_output+0x456/0x520 net/ipv6/ip6_output.c:163
dst_output ./include/net/dst.h:486
NF_HOOK ./include/linux/netfilter.h:257
ip6_xmit+0x1841/0x1c00 net/ipv6/ip6_output.c:261
sctp_v6_xmit+0x3b7/0x470 net/sctp/ipv6.c:225
sctp_packet_transmit+0x38cb/0x3a20 net/sctp/output.c:632
sctp_outq_flush+0xeb3/0x46e0 net/sctp/outqueue.c:885
sctp_outq_uncork+0xb2/0xd0 net/sctp/outqueue.c:750
sctp_side_effects net/sctp/sm_sideeffect.c:1773
sctp_do_sm+0x6962/0x6ec0 net/sctp/sm_sideeffect.c:1147
sctp_primitive_ASSOCIATE+0x12c/0x160 net/sctp/primitive.c:88
sctp_sendmsg+0x43e5/0x4f90 net/sctp/socket.c:1954
inet_sendmsg+0x498/0x670 net/ipv4/af_inet.c:762
sock_sendmsg_nosec net/socket.c:633
sock_sendmsg net/socket.c:643
SYSC_sendto+0x608/0x710 net/socket.c:1696
SyS_sendto+0x8a/0xb0 net/socket.c:1664
do_syscall_64+0xe6/0x130 arch/x86/entry/common.c:285
entry_SYSCALL64_slow_path+0x25/0x25 arch/x86/entry/entry_64.S:246
RIP: 0033:0x401133
RSP: 002b:
00007fff6d99cd38 EFLAGS:
00000246 ORIG_RAX:
000000000000002c
RAX:
ffffffffffffffda RBX:
00000000004002b0 RCX:
0000000000401133
RDX:
0000000000000001 RSI:
0000000000494088 RDI:
0000000000000003
RBP:
00007fff6d99cd90 R08:
00007fff6d99cd50 R09:
000000000000001c
R10:
0000000000000001 R11:
0000000000000246 R12:
0000000000000000
R13:
00000000004063d0 R14:
0000000000406460 R15:
0000000000000000
origin:
save_stack_trace+0x37/0x40 arch/x86/kernel/stacktrace.c:59
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:302
kmsan_internal_poison_shadow+0xb1/0x1a0 mm/kmsan/kmsan.c:198
kmsan_poison_shadow+0x6d/0xc0 mm/kmsan/kmsan.c:211
slab_alloc_node mm/slub.c:2743
__kmalloc_node_track_caller+0x200/0x360 mm/slub.c:4351
__kmalloc_reserve net/core/skbuff.c:138
__alloc_skb+0x26b/0x840 net/core/skbuff.c:231
alloc_skb ./include/linux/skbuff.h:933
sctp_packet_transmit+0x31e/0x3a20 net/sctp/output.c:570
sctp_outq_flush+0xeb3/0x46e0 net/sctp/outqueue.c:885
sctp_outq_uncork+0xb2/0xd0 net/sctp/outqueue.c:750
sctp_side_effects net/sctp/sm_sideeffect.c:1773
sctp_do_sm+0x6962/0x6ec0 net/sctp/sm_sideeffect.c:1147
sctp_primitive_ASSOCIATE+0x12c/0x160 net/sctp/primitive.c:88
sctp_sendmsg+0x43e5/0x4f90 net/sctp/socket.c:1954
inet_sendmsg+0x498/0x670 net/ipv4/af_inet.c:762
sock_sendmsg_nosec net/socket.c:633
sock_sendmsg net/socket.c:643
SYSC_sendto+0x608/0x710 net/socket.c:1696
SyS_sendto+0x8a/0xb0 net/socket.c:1664
do_syscall_64+0xe6/0x130 arch/x86/entry/common.c:285
return_from_SYSCALL_64+0x0/0x6a arch/x86/entry/entry_64.S:246
==================================================================
Signed-off-by: Alexander Potapenko <glider@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasily Averin [Fri, 14 Jul 2017 09:04:16 +0000 (12:04 +0300)]
ipv4: ip_do_fragment: fix headroom tests
Some time ago David Woodhouse reported skb_under_panic
when we try to push ethernet header to fragmented ipv6 skbs.
It was fixed for ipv6 by Florian Westphal in
commit
1d325d217c7f ("ipv6: ip6_fragment: fix headroom tests and skb leak")
However similar problem still exist in ipv4.
It does not trigger skb_under_panic due paranoid check
in ip_finish_output2, however according to Alexey Kuznetsov
current state is abnormal and ip_fragment should be fixed too.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhu Yanjun [Fri, 14 Jul 2017 03:01:27 +0000 (23:01 -0400)]
mlx4_en: remove unnecessary returned value check
The function __mlx4_zone_remove_one_entry always returns zero. So
it is not necessary to check it.
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason A. Donenfeld [Mon, 10 Jul 2017 12:00:32 +0000 (14:00 +0200)]
ioc3-eth: store pointer to net_device for priviate area
Computing the alignment manually for going from priv to pub is probably
not such a good idea, and in general the assumption that going from priv
to pub is possible trivially could change, so rather than relying on
that, we change things to just store a pointer to pub. This was sugested
by DaveM in [1].
[1] http://www.spinics.net/lists/netdev/msg443992.html
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 15 Jul 2017 21:28:28 +0000 (14:28 -0700)]
Merge branch 'bgmac-stingray-soc'
Abhishek Shah says:
====================
Extend BGMAC driver for Stingray SoC
The patchset extends Broadcom BGMAC driver for Broadcom Stingray SoC.
This patchset is based on Linux-4.12 and tested on NS2 and Stingray.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Abhishek Shah [Thu, 13 Jul 2017 19:04:09 +0000 (00:34 +0530)]
Documentation: devicetree: net: optional idm regs for bgmac
Specifying IDM register space in DT is not mendatory for SoCs
where firmware takes care of IDM operations. This patch updates
BGMAC driver's DT binding documentation indicating the same.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Oza Oza <oza.oza@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Abhishek Shah [Thu, 13 Jul 2017 19:04:08 +0000 (00:34 +0530)]
net: ethernet: bgmac: Make IDM register space optional
IDM operations are usually one time ops and should be done in
firmware itself. Driver is not supposed to touch IDM registers.
However, for some SoCs', driver is performing IDM read/writes.
So this patch masks IDM operations in case firmware is taking
care of IDM operations.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Reviewed-by: Oza Oza <oza.oza@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Abhishek Shah [Thu, 13 Jul 2017 19:04:07 +0000 (00:34 +0530)]
net: ethernet: bgmac: Remove unnecessary 'return' from platform_bgmac_idm_write
Return type for idm register write callback should be void as 'writel'
API is used for write operation. However, there no need to have 'return'
in this function.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Reviewed-by: Oza Oza <oza.oza@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Fri, 14 Jul 2017 14:07:33 +0000 (22:07 +0800)]
sctp: fix an array overflow when all ext chunks are set
Marcelo noticed an array overflow caused by commit
c28445c3cb07
("sctp: add reconf_enable in asoc ep and netns"), in which sctp
would add SCTP_CID_RECONF into extensions when reconf_enable is
set in sctp_make_init and sctp_make_init_ack.
Then now when all ext chunks are set, 4 ext chunk ids can be put
into extensions array while extensions array size is 3. It would
cause a kernel panic because of this overflow.
This patch is to fix it by defining extensions array size is 4 in
both sctp_make_init and sctp_make_init_ack.
Fixes:
c28445c3cb07 ("sctp: add reconf_enable in asoc ep and netns")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Fri, 14 Jul 2017 12:07:05 +0000 (14:07 +0200)]
liquidio: fix possible eeprom format string overflow
gcc reports that the temporary buffer for computing the
string length may be too small here:
drivers/net/ethernet/cavium/liquidio/lio_ethtool.c: In function 'lio_get_eeprom_len':
/drivers/net/ethernet/cavium/liquidio/lio_ethtool.c:345:21: error: 'sprintf' may write a terminating nul past the end of the destination [-Werror=format-overflow=]
len = sprintf(buf, "boardname:%s serialnum:%s maj:%lld min:%lld\n",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/cavium/liquidio/lio_ethtool.c:345:6: note: 'sprintf' output between 35 and 167 bytes into a destination of size 128
len = sprintf(buf, "boardname:%s serialnum:%s maj:%lld min:%lld\n",
This extends it to 192 bytes, which is certainly enough. As far
as I could tell, there are no other constraints that require a specific
maximum size.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Fri, 14 Jul 2017 12:07:04 +0000 (14:07 +0200)]
vmxnet3: avoid format strint overflow warning
gcc-7 notices that "-event-%d" could be more than 11 characters long
if we had larger 'vector' numbers:
drivers/net/vmxnet3/vmxnet3_drv.c: In function 'vmxnet3_activate_dev':
drivers/net/vmxnet3/vmxnet3_drv.c:2095:40: error: 'sprintf' may write a terminating nul past the end of the destination [-Werror=format-overflow=]
sprintf(intr->event_msi_vector_name, "%s-event-%d",
^~~~~~~~~~~~~
drivers/net/vmxnet3/vmxnet3_drv.c:2095:3: note: 'sprintf' output between 9 and 33 bytes into a destination of size 32
The current code is safe, but making the string a little longer
is harmless and lets gcc see that it's ok.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Fri, 14 Jul 2017 12:07:03 +0000 (14:07 +0200)]
net: thunder_bgx: avoid format string overflow warning
gcc warns that the temporary buffer might be too small here:
drivers/net/ethernet/cavium/thunder/thunder_bgx.c: In function 'bgx_probe':
drivers/net/ethernet/cavium/thunder/thunder_bgx.c:1020:16: error: '%d' directive writing between 1 and 10 bytes into a region of size between 9 and 11 [-Werror=format-overflow=]
sprintf(str, "BGX%d LMAC%d mode", bgx->bgx_id, lmacid);
^~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/cavium/thunder/thunder_bgx.c:1020:16: note: directive argument in the range [0,
2147483647]
drivers/net/ethernet/cavium/thunder/thunder_bgx.c:1020:3: note: 'sprintf' output between 16 and 27 bytes into a destination of size 20
This probably can't happen, but it can't hurt to make it long
enough for the theoretical limit.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Fri, 14 Jul 2017 12:07:02 +0000 (14:07 +0200)]
bnx2x: fix format overflow warning
gcc notices that large queue numbers would overflow the queue name
string:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c: In function 'bnx2x_get_strings':
drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c:3165:25: error: '%d' directive writing between 1 and 10 bytes into a region of size 5 [-Werror=format-overflow=]
drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c:3165:25: note: directive argument in the range [0,
2147483647]
drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c:3165:5: note: 'sprintf' output between 2 and 11 bytes into a destination of size 5
There is a hard limit in place that makes the number at most two
digits, so the code is fine. This changes it to use snprintf()
to truncate instead of overflowing, which shuts up that warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Fri, 14 Jul 2017 12:07:01 +0000 (14:07 +0200)]
net: niu: fix format string overflow warning:
We get a warning for the port_name string that might be longer than
six characters if we had more than 10 ports:
drivers/net/ethernet/sun/niu.c: In function 'niu_put_parent':
drivers/net/ethernet/sun/niu.c:9563:21: error: '%d' directive writing between 1 and 3 bytes into a region of size 2 [-Werror=format-overflow=]
sprintf(port_name, "port%d", port);
^~~~~~~~
drivers/net/ethernet/sun/niu.c:9563:21: note: directive argument in the range [0, 255]
drivers/net/ethernet/sun/niu.c:9563:2: note: 'sprintf' output between 6 and 8 bytes into a destination of size 6
sprintf(port_name, "port%d", port);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/sun/niu.c: In function 'niu_pci_init_one':
drivers/net/ethernet/sun/niu.c:9538:22: error: '%d' directive writing between 1 and 3 bytes into a region of size 2 [-Werror=format-overflow=]
sprintf(port_name, "port%d", port);
^~~~~~~~
drivers/net/ethernet/sun/niu.c:9538:22: note: directive argument in the range [0, 255]
drivers/net/ethernet/sun/niu.c:9538:3: note: 'sprintf' output between 6 and 8 bytes into a destination of size 6
While we know that the port number is small, there is no harm in
making the format string two bytes longer to avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Fri, 14 Jul 2017 12:07:00 +0000 (14:07 +0200)]
isdn: divert: fix sprintf buffer overflow warning
One string we pass into the cs->info buffer might be too long,
as pointed out by gcc:
drivers/isdn/divert/isdn_divert.c: In function 'll_callback':
drivers/isdn/divert/isdn_divert.c:488:22: error: '%d' directive writing between 1 and 3 bytes into a region of size between 1 and 69 [-Werror=format-overflow=]
sprintf(cs->info, "%d 0x%lx %s %s %s %s 0x%x 0x%x %d %d %s\n",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/isdn/divert/isdn_divert.c:488:22: note: directive argument in the range [0, 255]
drivers/isdn/divert/isdn_divert.c:488:4: note: 'sprintf' output 25 or more bytes (assuming 129) into a destination of size 90
This is unlikely to actually cause problems, so let's use snprintf
as a simple workaround to shut up the warning and truncate the
buffer instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Timur Tabi [Thu, 13 Jul 2017 20:45:41 +0000 (15:45 -0500)]
net: qcom/emac: fix double free of SGMII IRQ during shutdown
If the interface is not up, then don't try to close it during a
shutdown. This avoids possible double free of the IRQ, which
can happen during a shutdown.
Fixes:
03eb3eb4d4d5 ("net: qcom/emac: add shutdown function")
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Kulhavy [Thu, 13 Jul 2017 17:40:57 +0000 (19:40 +0200)]
smsc95xx: use ethtool_op_get_ts_info()
This change enables the use of SW timestamping on Raspberry PI.
smsc95xx uses the usbnet transmit function usbnet_start_xmit(), which
implements software timestamping. However the SOF_TIMESTAMPING_TX_SOFTWARE
capability was missing and only SOF_TIMESTAMPING_RX_SOFTWARE was announced.
By using ethtool_op_get_ts_info() as get_ts_info() also the
SOF_TIMESTAMPING_TX_SOFTWARE is announced.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roman Mashak [Thu, 13 Jul 2017 17:12:18 +0000 (13:12 -0400)]
net sched actions: rename act_get_notify() to tcf_get_notify()
Make name consistent with other TC event notification routines, such as
tcf_add_notify() and tcf_del_notify()
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Iván Briano [Thu, 13 Jul 2017 16:46:58 +0000 (09:46 -0700)]
net/packet: Fix Tx queue selection for AF_PACKET
When PACKET_QDISC_BYPASS is not used, Tx queue selection will be done
before the packet is enqueued, taking into account any mappings set by
a queuing discipline such as mqprio without hardware offloading. This
selection may be affected by a previously saved queue_mapping, either on
the Rx path, or done before the packet reaches the device, as it's
currently the case for AF_PACKET.
In order for queue selection to work as expected when using traffic
control, there can't be another selection done before that point is
reached, so move the call to packet_pick_tx_queue to
packet_direct_xmit, leaving the default xmit path as it was before
PACKET_QDISC_BYPASS was introduced.
A forward declaration of packet_pick_tx_queue() is introduced to avoid
the need to reorder the functions within the file.
Fixes:
d346a3fae3ff ("packet: introduce PACKET_QDISC_BYPASS socket option")
Signed-off-by: Iván Briano <ivan.briano@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Thu, 13 Jul 2017 13:09:10 +0000 (16:09 +0300)]
net: bridge: fix dest lookup when vlan proto doesn't match
With 802.1ad support the vlan_ingress code started checking for vlan
protocol mismatch which causes the current tag to be inserted and the
bridge vlan protocol & pvid to be set. The vlan tag insertion changes
the skb mac_header and thus the lookup mac dest pointer which was loaded
prior to calling br_allowed_ingress in br_handle_frame_finish is VLAN_HLEN
bytes off now, pointing to the last two bytes of the destination mac and
the first four of the source mac causing lookups to always fail and
broadcasting all such packets to all ports. Same thing happens for locally
originated packets when passing via br_dev_xmit. So load the dest pointer
after the vlan checks and possible skb change.
Fixes:
8580e2117c06 ("bridge: Prepare for 802.1ad vlan filtering support")
Reported-by: Anitha Narasimha Murthy <anitha@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Thu, 13 Jul 2017 13:06:50 +0000 (18:36 +0530)]
cxgb4: ptp_clock_register() returns error pointers
Check ptp_clock_register() return not only for NULL but
also for error pointers, and also nullify adapter->ptp_clock
if ptp_clock_register() fails.
Fixes:
9c33e4208bce ("cxgb4: Add PTP Hardware Clock (PHC) support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LiuJian [Thu, 13 Jul 2017 10:57:54 +0000 (18:57 +0800)]
net: hns: add acpi function of xge led control
The current code only support DT method to control xge led.
This patch is the implementation of acpi method to control xge led.
Signed-off-by: LiuJian <liujian56@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Wed, 12 Jul 2017 22:56:41 +0000 (15:56 -0700)]
netpoll: shut up a kernel warning on refcount
When we convert atomic_t to refcount_t, a new kernel warning
on "increment on 0" is introduced in the netpoll code,
zap_completion_queue(). In fact for this special case, we know
the refcount is 0 and we just have to set it to 1 to satisfy
the following dev_kfree_skb_any(), so we can just use
refcount_set(..., 1) instead.
Fixes:
633547973ffc ("net: convert sk_buff.users from atomic_t to refcount_t")
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Cc: Reshetova, Elena <elena.reshetova@intel.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enrico Mioso [Tue, 11 Jul 2017 15:21:52 +0000 (17:21 +0200)]
cdc_ncm: Set NTB format again after altsetting switch for Huawei devices
Some firmwares in Huawei E3372H devices have been observed to switch back
to NTB 32-bit format after altsetting switch.
This patch implements a driver flag to check for the device settings and
set NTB format to 16-bit again if needed.
The flag has been activated for devices controlled by the huawei_cdc_ncm.c
driver.
V1->V2:
- fixed broken error checks
- some corrections to the commit message
V2->V3:
- variable name changes, to clarify what's happening
- check (and possibly set) the NTB format later in the common bind code path
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Reported-and-tested-by: Christian Panton <christian@panton.org>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
CC: Bjørn Mork <bjorn@mork.no>
CC: Christian Panton <christian@panton.org>
CC: linux-usb@vger.kernel.org
CC: netdev@vger.kernel.org
CC: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Blumenstingl [Mon, 10 Jul 2017 12:35:23 +0000 (14:35 +0200)]
mdio: mux: fix parsing mux registers outside of the PHY address range
mdio_mux_init parses the child nodes of the MDIO mux. When using
"mdio-mux-mmioreg" the child nodes are describing the register value
that is written to switch between the MDIO busses.
The change which makes the error messages more verbose changed the
parsing of the "reg" property from a simple of_property_read_u32 call
to of_mdio_parse_addr. On a Khadas VIM (based on the Meson GXL SoC,
which uses mdio-mux-mmioreg) this prevents registering the MDIO mux
(because the "reg" values on the MDIO mux child nodes are 0x2009087f
and 0xe40908ff) and leads to the following errors:
mdio-mux-mmioreg
c883455c.eth-phy-mux: /soc/periphs@
c8834000/eth-phy-mux/mdio@
e40908ff PHY address -
469169921 is too large
mdio-mux-mmioreg
c883455c.eth-phy-mux: Error: Failed to find reg for child /soc/periphs@
c8834000/eth-phy-mux/mdio@
e40908ff
mdio-mux-mmioreg
c883455c.eth-phy-mux: /soc/periphs@
c8834000/eth-phy-mux/mdio@
2009087f PHY address
537462911 is too large
mdio-mux-mmioreg
c883455c.eth-phy-mux: Error: Failed to find reg for child /soc/periphs@
c8834000/eth-phy-mux/mdio@
2009087f
mdio-mux-mmioreg
c883455c.eth-phy-mux: Error: No acceptable child buses found
mdio-mux-mmioreg
c883455c.eth-phy-mux: failed to register mdio-mux bus /soc/periphs@
c8834000/eth-phy-mux
(as a result of that ethernet is not working, because the PHY which is
connected through the mux' child MDIO bus, which is not being
registered).
Fix this by reverting the change from of_mdio_parse_addr to
of_mdio_parse_addr.
Fixes:
342fa1964439 ("mdio: mux: make child bus walking more permissive and errors more verbose")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 13 Jul 2017 20:36:40 +0000 (13:36 -0700)]
net: set fib rule refcount after malloc
The configure callback of fib_rules_ops can change the refcnt of a
fib rule. For instance, mlxsw takes a refcnt when adding the processing
of the rule to a work queue. Thus the rule refcnt can not be reset to
to 1 afterwards. Move the refcnt setting to after the allocation.
Fixes:
5361e209dd30 ("net: avoid one splat in fib_nl_delrule()")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rolf Eike Beer [Thu, 13 Jul 2017 14:46:43 +0000 (16:46 +0200)]
netlink: correctly document nla_put_u64_64bit()
Signed-off-by: Rolf Eike Beer <eb@emlix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Thu, 13 Jul 2017 13:15:07 +0000 (18:45 +0530)]
cxgb4: add new T5 pci device id's
Add 0x50a3 and 0x50a4 T5 device id's
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Thu, 13 Jul 2017 11:22:24 +0000 (12:22 +0100)]
dccp: make const array error_code static
Don't populate array error_code on the stack but make it static. Makes
the object code smaller by almost 250 bytes:
Before:
text data bss dec hex filename
10366 983 0 11349 2c55 net/dccp/input.o
After:
text data bss dec hex filename
10161 1039 0 11200 2bc0 net/dccp/input.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Tue, 11 Jul 2017 11:47:33 +0000 (12:47 +0100)]
rt2x00: make const array glrt_table static
Don't populate array glrt_table on the stack but make it static.
Makes the object code a smaller by over 670 bytes:
Before:
text data bss dec hex filename
131772 4733 0 136505 21539 rt2800lib.o
After:
text data bss dec hex filename
131043 4789 0 135832 21298 rt2800lib.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Tue, 11 Jul 2017 11:18:48 +0000 (12:18 +0100)]
net: stmmac: make const array route_possibilities static
Don't populate array route_possibilities on the stack but make it
static const. Makes the object code a little smaller by 85 bytes:
Before:
text data bss dec hex filename
9901 2448 0 12349 303d dwmac4_core.o
After:
text data bss dec hex filename
9760 2504 0 12264 2fe8 dwmac4_core.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Tue, 11 Jul 2017 10:52:23 +0000 (11:52 +0100)]
net: broadcom: bnx2x: make a couple of const arrays static
Don't populate various tables on the stack but make them static const.
Makes the object code smaller by nearly 200 bytes:
Before:
text data bss dec hex filename
113468 11200 0 124668 1e6fc bnx2x_ethtool.o
After:
text data bss dec hex filename
113129 11344 0 124473 1e639 bnx2x_ethtool.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Bogendoerfer [Thu, 13 Jul 2017 08:57:40 +0000 (10:57 +0200)]
xgene: Don't fail probe, if there is no clk resource for SGMII interfaces
This change fixes following problem
[ 1.827940] xgene-enet: probe of
1f210030.ethernet failed with error -2
which leads to a missing ethernet interface (reproducable at least on
Gigabyte MP30-AR0 and APM Mustang systems).
The check for a valid clk resource fails, because DT doesn't provide a
clock for sgenet1. But the driver doesn't use this clk, if the ethernet
port is connected via SGMII. Therefore this patch avoids probing for clk
on SGMII interfaces.
Fixes:
9aea7779b764 ("drivers: net: xgene: Fix crash on DT systems")
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kefeng Wang [Thu, 13 Jul 2017 06:27:58 +0000 (14:27 +0800)]
bpf: fix return in bpf_skb_adjust_net
The bpf_skb_adjust_net() ignores the return value of bpf_skb_net_shrink/grow,
and always return 0, fix it by return 'ret'.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 13 Jul 2017 02:30:57 +0000 (19:30 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Fix 64-bit division in mlx5 IPSEC offload support, from Ilan Tayari
and Arnd Bergmann.
2) Fix race in statistics gathering in bnxt_en driver, from Michael
Chan.
3) Can't use a mutex in RCU reader protected section on tap driver, from
Cong WANG.
4) Fix mdb leak in bridging code, from Eduardo Valentin.
5) Fix free of wrong pointer variable in nfp driver, from Dan Carpenter.
6) Buffer overflow in brcmfmac driver, from Arend van SPriel.
7) ioremap_nocache() return value needs to be checked in smsc911x
driver, from Alexey Khoroshilov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (34 commits)
net: stmmac: revert "support future possible different internal phy mode"
sfc: don't read beyond unicast address list
datagram: fix kernel-doc comments
socket: add documentation for missing elements
smsc911x: Add check for ioremap_nocache() return code
brcmfmac: fix possible buffer overflow in brcmf_cfg80211_mgmt_tx()
net: hns: Bugfix for Tx timeout handling in hns driver
net: ipmr: ipmr_get_table() returns NULL
nfp: freeing the wrong variable
mlxsw: spectrum_switchdev: Check status of memory allocation
mlxsw: spectrum_switchdev: Remove unused variable
mlxsw: spectrum_router: Fix use-after-free in route replace
mlxsw: spectrum_router: Add missing rollback
samples/bpf: fix a build issue
bridge: mdb: fix leak on complete_info ptr on fail path
tap: convert a mutex to a spinlock
cxgb4: fix BUG() on interrupt deallocating path of ULD
qed: Fix printk option passed when printing ipv6 addresses
net: Fix minor code bug in timestamping.txt
net: stmmac: Make 'alloc_dma_[rt]x_desc_resources()' look even closer
...
Linus Torvalds [Thu, 13 Jul 2017 02:25:47 +0000 (19:25 -0700)]
disable new gcc-7.1.1 warnings for now
I made the mistake of upgrading my desktop to the new Fedora 26 that
comes with gcc-7.1.1.
There's nothing wrong per se that I've noticed, but I now have 1500
lines of warnings, mostly from the new format-truncation warning
triggering all over the tree.
We use 'snprintf()' and friends in a lot of places, and often know that
the numbers are fairly small (ie a controller index or similar), but gcc
doesn't know that, and sees an 'int', and thinks that it could be some
huge number. And then complains when our buffers are not able to fit
the name for the ten millionth controller.
These warnings aren't necessarily bad per se, and we probably want to
look through them subsystem by subsystem, but at least during the merge
window they just mean that I can't even see if somebody is introducing
any *real* problems when I pull.
So warnings disabled for now.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 13 Jul 2017 00:22:01 +0000 (17:22 -0700)]
Merge tag 'modules-for-v4.13' of git://git./linux/kernel/git/jeyu/linux
Pull modules updates from Jessica Yu:
"Summary of modules changes for the 4.13 merge window:
- Minor code cleanups
- Avoid accessing mod struct prior to checking module struct version,
from Kees
- Fix racy atomic inc/dec logic of kmod_concurrent_max in kmod, from
Luis"
* tag 'modules-for-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: make the modinfo name const
kmod: reduce atomic operations on kmod_concurrent and simplify
module: use list_for_each_entry_rcu() on find_module_all()
kernel/module.c: suppress warning about unused nowarn variable
module: Add module name to modinfo
module: Pass struct load_info into symbol checks
LABBE Corentin [Wed, 12 Jul 2017 07:32:34 +0000 (09:32 +0200)]
net: stmmac: revert "support future possible different internal phy mode"
Since internal phy-mode is reserved for non-xMII protocol we cannot use
it with dwmac-sun8i.
Furthermore, all DT patchs which comes with this patch were cleaned, so
the current state is broken.
This reverts commit
1c2fa5f84683 ("net: stmmac: support future possible different internal phy mode")
Fixes:
1c2fa5f84683 ("net: stmmac: support future possible different internal phy mode")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bert Kenward [Wed, 12 Jul 2017 16:19:41 +0000 (17:19 +0100)]
sfc: don't read beyond unicast address list
If we have more than 32 unicast MAC addresses assigned to an interface
we will read beyond the end of the address table in the driver when
adding filters. The next 256 entries store multicast addresses, so we
will end up attempting to insert duplicate filters, which is mostly
harmless. If we add more than 288 unicast addresses we will then read
past the multicast address table, which is likely to be more exciting.
Fixes:
12fb0da45c9a ("sfc: clean fallbacks between promisc/normal in efx_ef10_filter_sync_rx_mode")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 12 Jul 2017 21:39:44 +0000 (14:39 -0700)]
Merge branch 'net-doc-fixes'
Stephen Hemminger says:
====================
minor net kernel-doc fixes
Fix a couple of small errors in kernel-doc for networking
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Wed, 12 Jul 2017 16:29:07 +0000 (09:29 -0700)]
datagram: fix kernel-doc comments
An underscore in the kernel-doc comment section has special meaning
and mis-use generates an errors.
./net/core/datagram.c:207: ERROR: Unknown target name: "msg".
./net/core/datagram.c:379: ERROR: Unknown target name: "msg".
./net/core/datagram.c:816: ERROR: Unknown target name: "t".
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Wed, 12 Jul 2017 16:29:06 +0000 (09:29 -0700)]
socket: add documentation for missing elements
Fill in missing kernel-doc for missing elements in struct sock.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Khoroshilov [Wed, 12 Jul 2017 20:58:56 +0000 (23:58 +0300)]
smsc911x: Add check for ioremap_nocache() return code
There is no check for return code of smsc911x_drv_probe()
in smsc911x_drv_probe(). The patch adds one.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 12 Jul 2017 17:04:56 +0000 (10:04 -0700)]
Merge branch 'i2c/for-4.13' of git://git./linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"This pull request contains:
- i2c core reorganization. One source file became too monolithic. It
is now split up, yet we still have the same named object as the
final output. This should ease maintenance.
- new drivers: ZTE ZX2967 family, ASPEED 24XX/25XX
- designware driver gained slave mode support
- xgene-slimpro driver gained ACPI support
- bigger overhaul for pca-platform driver
- the algo-bit module now supports messages with enforced STOP
- slightly bigger than usual set of driver updates and improvements
and with much appreciated quality assurance from Andy Shevchenko"
* 'i2c/for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (51 commits)
i2c: Provide a stub for i2c_detect_slave_mode()
i2c: designware: Let slave adapter support be optional
i2c: designware: Make HW init functions static
i2c: designware: fix spelling mistakes
i2c: pca-platform: propagate error from i2c_pca_add_numbered_bus
i2c: pca-platform: correctly set algo_data.reset_chip
i2c: acpi: Do not create i2c-clients for LNXVIDEO ACPI devices
i2c: designware: enable SLAVE in platform module
i2c: designware: add SLAVE mode functions
i2c: zx2967: drop COMPILE_TEST dependency
i2c: zx2967: always use the same device when printing errors
i2c: pca-platform: use dev_warn/dev_info instead of printk
i2c: pca-platform: use device managed allocations
i2c: pca-platform: add devicetree awareness
i2c: pca-platform: switch to struct gpio_desc
dt-bindings: add bindings for i2c-pca-platform
i2c: cadance: fix ctrl/addr reg write order
i2c: zx2967: add i2c controller driver for ZTE's zx2967 family
dt: bindings: add documentation for zx2967 family i2c controller
i2c: algo-bit: add support for I2C_M_STOP
...
Linus Torvalds [Wed, 12 Jul 2017 17:00:04 +0000 (10:00 -0700)]
Merge tag 'iommu-updates-v4.13' of git://git./linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"This update comes with:
- Support for lockless operation in the ARM io-pgtable code.
This is an important step to solve the scalability problems in the
common dma-iommu code for ARM
- Some Errata workarounds for ARM SMMU implemenations
- Rewrite of the deferred IO/TLB flush code in the AMD IOMMU driver.
The code suffered from very high flush rates, with the new
implementation the flush rate is down to ~1% of what it was before
- Support for amd_iommu=off when booting with kexec.
The problem here was that the IOMMU driver bailed out early without
disabling the iommu hardware, if it was enabled in the old kernel
- The Rockchip IOMMU driver is now available on ARM64
- Align the return value of the iommu_ops->device_group call-backs to
not miss error values
- Preempt-disable optimizations in the Intel VT-d and common IOVA
code to help Linux-RT
- Various other small cleanups and fixes"
* tag 'iommu-updates-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (60 commits)
iommu/vt-d: Constify intel_dma_ops
iommu: Warn once when device_group callback returns NULL
iommu/omap: Return ERR_PTR in device_group call-back
iommu: Return ERR_PTR() values from device_group call-backs
iommu/s390: Use iommu_group_get_for_dev() in s390_iommu_add_device()
iommu/vt-d: Don't disable preemption while accessing deferred_flush()
iommu/iova: Don't disable preempt around this_cpu_ptr()
iommu/arm-smmu-v3: Add workaround for Cavium ThunderX2 erratum #126
iommu/arm-smmu-v3: Enable ACPI based HiSilicon CMD_PREFETCH quirk(erratum
161010701)
iommu/arm-smmu-v3: Add workaround for Cavium ThunderX2 erratum #74
ACPI/IORT: Fixup SMMUv3 resource size for Cavium ThunderX2 SMMUv3 model
iommu/arm-smmu-v3, acpi: Add temporary Cavium SMMU-V3 IORT model number definitions
iommu/io-pgtable-arm: Use dma_wmb() instead of wmb() when publishing table
iommu/io-pgtable: depend on !GENERIC_ATOMIC64 when using COMPILE_TEST with LPAE
iommu/arm-smmu-v3: Remove io-pgtable spinlock
iommu/arm-smmu: Remove io-pgtable spinlock
iommu/io-pgtable-arm-v7s: Support lockless operation
iommu/io-pgtable-arm: Support lockless operation
iommu/io-pgtable: Introduce explicit coherency
iommu/io-pgtable-arm-v7s: Refactor split_blk_unmap
...
Linus Torvalds [Wed, 12 Jul 2017 16:28:55 +0000 (09:28 -0700)]
Merge branch 'overlayfs-linus' of git://git./linux/kernel/git/mszeredi/vfs
Pull overlayfs updates from Miklos Szeredi:
"This work from Amir introduces the inodes index feature, which
provides:
- hardlinks are not broken on copy up
- infrastructure for overlayfs NFS export
This also fixes constant st_ino for samefs case for lower hardlinks"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs: (33 commits)
ovl: mark parent impure and restore timestamp on ovl_link_up()
ovl: document copying layers restrictions with inodes index
ovl: cleanup orphan index entries
ovl: persistent overlay inode nlink for indexed inodes
ovl: implement index dir copy up
ovl: move copy up lock out
ovl: rearrange copy up
ovl: add flag for upper in ovl_entry
ovl: use struct copy_up_ctx as function argument
ovl: base tmpfile in workdir too
ovl: factor out ovl_copy_up_inode() helper
ovl: extract helper to get temp file in copy up
ovl: defer upper dir lock to tempfile link
ovl: hash overlay non-dir inodes by copy up origin
ovl: cleanup bad and stale index entries on mount
ovl: lookup index entry for copy up origin
ovl: verify index dir matches upper dir
ovl: verify upper root dir matches lower root dir
ovl: introduce the inodes index dir feature
ovl: generalize ovl_create_workdir()
...
Al Viro [Wed, 12 Jul 2017 03:59:45 +0000 (04:59 +0100)]
fix a braino in compat_sys_getrlimit()
Reported-and-tested-by: Meelis Roos <mroos@linux.ee>
Fixes: commit
d9e968cb9f84 "getrlimit()/setrlimit(): move compat to native"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arend van Spriel [Fri, 7 Jul 2017 20:09:06 +0000 (21:09 +0100)]
brcmfmac: fix possible buffer overflow in brcmf_cfg80211_mgmt_tx()
The lower level nl80211 code in cfg80211 ensures that "len" is between
25 and NL80211_ATTR_FRAME (2304). We subtract DOT11_MGMT_HDR_LEN (24) from
"len" so thats's max of 2280. However, the action_frame->data[] buffer is
only BRCMF_FIL_ACTION_FRAME_SIZE (1800) bytes long so this memcpy() can
overflow.
memcpy(action_frame->data, &buf[DOT11_MGMT_HDR_LEN],
le16_to_cpu(action_frame->len));
Cc: stable@vger.kernel.org # 3.9.x
Fixes:
18e2f61db3b70 ("brcmfmac: P2P action frame tx.")
Reported-by: "freenerguo(郭大兴)" <freenerguo@tencent.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lin Yun Sheng [Wed, 12 Jul 2017 11:09:59 +0000 (19:09 +0800)]
net: hns: Bugfix for Tx timeout handling in hns driver
When hns port type is not debug mode, netif_tx_disable is called
when there is a tx timeout, which requires system reboot to return
to normal state. This patch fix this problem by resetting the net
dev.
Fixes:
b5996f11ea54 ("net: add Hisilicon Network Subsystem basic ethernet support")
Signed-off-by: Lin Yun Sheng <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 12 Jul 2017 07:56:47 +0000 (10:56 +0300)]
net: ipmr: ipmr_get_table() returns NULL
The ipmr_get_table() function doesn't return error pointers it returns
NULL on error.
Fixes:
4f75ba6982bc ("net: ipmr: Add ipmr_rtm_getroute")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 12 Jul 2017 07:42:06 +0000 (10:42 +0300)]
nfp: freeing the wrong variable
We accidentally free a NULL pointer and leak the pointer we want to
free. Also you can tell from the label name what was intended. :)
Fixes:
abfcdc1de9bf ("nfp: add a stats handler for flower offloads")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 12 Jul 2017 15:15:52 +0000 (08:15 -0700)]
Merge branch 'mlxsw-spectrum-Various-fixes'
Jiri Pirko says:
====================
mlxsw: spectrum: Various fixes
First patch adds a missing rollback in error path. Second patch prevents
a use-after-free during IPv4 route replace. Last two patches fix warnings
from static checkers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 12 Jul 2017 07:12:55 +0000 (09:12 +0200)]
mlxsw: spectrum_switchdev: Check status of memory allocation
We can't rely on kzalloc() always succeeding, so check its return value.
Suppresses the following smatch error:
mlxsw_sp_switchdev_event() error: potential null dereference
'switchdev_work->fdb_info.addr'. (kzalloc returns
null)
Fixes:
af061378924f ("mlxsw: spectrum_switchdev: Add support for learning FDB through notification")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 12 Jul 2017 07:12:54 +0000 (09:12 +0200)]
mlxsw: spectrum_switchdev: Remove unused variable
Commit
10e23eb299fa ("mlxsw: spectrum: Remove support for bypass bridge
port attributes/vlan set") removed statements that used 'bridge_vlan',
but didn't remove the variable itself resulting in the following warning
with W=1:
warning: variable ‘bridge_vlan’ set but not used
[-Wunused-but-set-variable]
Remove the variable and suppress the warning.
Fixes:
10e23eb299fa ("mlxsw: spectrum: Remove support for bypass bridge port attributes/vlan set")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 12 Jul 2017 07:12:53 +0000 (09:12 +0200)]
mlxsw: spectrum_router: Fix use-after-free in route replace
While working on IPv6 route replace I realized we can have a
use-after-free in IPv4 in case the replaced route is offloaded and the
only one using its FIB info.
The problem is that fib_table_insert() drops the reference on the FIB
info of the replaced routes which is eventually freed via call_rcu().
Since the driver doesn't hold a reference on this FIB info it can cause
a use-after-free when it tries to clear the RTNH_F_OFFLOAD flag stored
in fi->fib_flags.
After running the following commands in a loop for enough time with a
KASAN enabled kernel I finally got the below trace.
$ ip route add 192.168.50.0/24 via 192.168.200.1 dev enp3s0np3
$ ip route replace 192.168.50.0/24 dev enp3s0np5
$ ip route del 192.168.50.0/24 dev enp3s0np5
BUG: KASAN: use-after-free in mlxsw_sp_fib_entry_offload_unset+0xa7/0x120 [mlxsw_spectrum]
Read of size 4 at addr
ffff8803717d9820 by task kworker/u4:2/55
[...]
? mlxsw_sp_fib_entry_offload_unset+0xa7/0x120 [mlxsw_spectrum]
? mlxsw_sp_fib_entry_offload_unset+0xa7/0x120 [mlxsw_spectrum]
? mlxsw_sp_router_neighs_update_work+0x1cd0/0x1ce0 [mlxsw_spectrum]
? mlxsw_sp_fib_entry_offload_unset+0xa7/0x120 [mlxsw_spectrum]
__asan_load4+0x61/0x80
mlxsw_sp_fib_entry_offload_unset+0xa7/0x120 [mlxsw_spectrum]
mlxsw_sp_fib_entry_offload_refresh+0xb6/0x370 [mlxsw_spectrum]
mlxsw_sp_router_fib_event_work+0xd1c/0x2780 [mlxsw_spectrum]
[...]
Freed by task 5131:
save_stack_trace+0x16/0x20
save_stack+0x46/0xd0
kasan_slab_free+0x70/0xc0
kfree+0x144/0x570
free_fib_info_rcu+0x2e7/0x410
rcu_process_callbacks+0x4f8/0xe30
__do_softirq+0x1d3/0x9e2
Fix this by taking a reference on the FIB info when creating the nexthop
group it represents and drop it when the group is destroyed.
Fixes:
599cf8f95f22 ("mlxsw: spectrum_router: Add support for route replace")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 12 Jul 2017 07:12:52 +0000 (09:12 +0200)]
mlxsw: spectrum_router: Add missing rollback
With this patch the error path of mlxsw_sp_nexthop_init() is symmetric
with mlxsw_sp_nexthop_fini(). Noticed during code review.
Fixes:
a8c970142798 ("mlxsw: spectrum_router: Refactor nexthop init routine")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 12 Jul 2017 04:34:24 +0000 (21:34 -0700)]
Merge git://git./linux/kernel/git/davem/sparc
Pull sparc fixes from David Miller:
- Fix symbol version generation for assembler on sparc, from
Nagarathnam Muthusamy.
- Fix compound page handling in gup_huge_pmd(), from Nitin Gupta.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix gup_huge_pmd
Adding the type of exported symbols
sed regex in Makefile.build requires line break between exported symbols
Adding asm-prototypes.h for genksyms to generate crc
Yonghong Song [Mon, 10 Jul 2017 21:04:28 +0000 (14:04 -0700)]
samples/bpf: fix a build issue
With latest net-next:
====
clang -nostdinc -isystem /usr/lib/gcc/x86_64-redhat-linux/6.3.1/include -I./arch/x86/include -I./arch/x86/include/generated/uapi -I./arch/x86/include/generated -I./include -I./arch/x86/include/uapi -I./include/uapi -I./include/generated/uapi -include ./include/linux/kconfig.h -Isamples/bpf \
-D__KERNEL__ -D__ASM_SYSREG_H -Wno-unused-value -Wno-pointer-sign \
-Wno-compare-distinct-pointer-types \
-Wno-gnu-variable-sized-type-not-at-end \
-Wno-address-of-packed-member -Wno-tautological-compare \
-Wno-unknown-warning-option \
-O2 -emit-llvm -c samples/bpf/tcp_synrto_kern.c -o -| llc -march=bpf -filetype=obj -o samples/bpf/tcp_synrto_kern.o
samples/bpf/tcp_synrto_kern.c:20:10: fatal error: 'bpf_endian.h' file not found
^~~~~~~~~~~~~~
1 error generated.
====
net has the same issue.
Add support for ntohl and htonl in tools/testing/selftests/bpf/bpf_endian.h.
Also move bpf_helpers.h from samples/bpf to selftests/bpf and change
compiler include logic so that programs in samples/bpf can access the headers
in selftests/bpf, but not the other way around.
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eduardo Valentin [Tue, 11 Jul 2017 21:55:12 +0000 (14:55 -0700)]
bridge: mdb: fix leak on complete_info ptr on fail path
We currently get the following kmemleak report:
unreferenced object 0xffff8800039d9820 (size 32):
comm "softirq", pid 0, jiffies
4295212383 (age 792.416s)
hex dump (first 32 bytes):
00 0c e0 03 00 88 ff ff ff 02 00 00 00 00 00 00 ................
00 00 00 01 ff 11 00 02 86 dd 00 00 ff ff ff ff ................
backtrace:
[<
ffffffff8152b4aa>] kmemleak_alloc+0x4a/0xa0
[<
ffffffff811d8ec8>] kmem_cache_alloc_trace+0xb8/0x1c0
[<
ffffffffa0389683>] __br_mdb_notify+0x2a3/0x300 [bridge]
[<
ffffffffa038a0ce>] br_mdb_notify+0x6e/0x70 [bridge]
[<
ffffffffa0386479>] br_multicast_add_group+0x109/0x150 [bridge]
[<
ffffffffa0386518>] br_ip6_multicast_add_group+0x58/0x60 [bridge]
[<
ffffffffa0387fb5>] br_multicast_rcv+0x1d5/0xdb0 [bridge]
[<
ffffffffa037d7cf>] br_handle_frame_finish+0xcf/0x510 [bridge]
[<
ffffffffa03a236b>] br_nf_hook_thresh.part.27+0xb/0x10 [br_netfilter]
[<
ffffffffa03a3738>] br_nf_hook_thresh+0x48/0xb0 [br_netfilter]
[<
ffffffffa03a3fb9>] br_nf_pre_routing_finish_ipv6+0x109/0x1d0 [br_netfilter]
[<
ffffffffa03a4400>] br_nf_pre_routing_ipv6+0xd0/0x14c [br_netfilter]
[<
ffffffffa03a3c27>] br_nf_pre_routing+0x197/0x3d0 [br_netfilter]
[<
ffffffff814a2952>] nf_iterate+0x52/0x60
[<
ffffffff814a29bc>] nf_hook_slow+0x5c/0xb0
[<
ffffffffa037ddf4>] br_handle_frame+0x1a4/0x2c0 [bridge]
This happens when switchdev_port_obj_add() fails. This patch
frees complete_info object in the fail path.
Reviewed-by: Vallish Vaidyeshwara <vallish@amazon.com>
Signed-off-by: Eduardo Valentin <eduval@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>