Margarita Olaya Cabrera [Wed, 15 Dec 2010 01:00:21 +0000 (19:00 -0600)]
ASoC: twl6040: Add ramp up/down volume for HS and HF
Add ramp functions for the headset and handsfree outputs
in order to reduce the pops during power on/off sequences.
In order to give more control to volume ramp, step size and delay
between steps can be specified.
The patches are based on wm8350 implementation from Liam
Girdwood.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Olaya, Margarita [Wed, 15 Dec 2010 01:18:36 +0000 (19:18 -0600)]
ASoC: twl6040: Set default gains to minimun value
Updated default values to improve power consumption.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Misael Lopez Cruz [Sat, 11 Dec 2010 03:06:34 +0000 (21:06 -0600)]
ASoC: twl6040: Use correct offset for LineInAmp Right
Gain for LineInAmp Right uses LINEGAIN[5:3], which means that
offset for right channel should be 4.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Olaya, Margarita [Sat, 11 Dec 2010 03:06:39 +0000 (21:06 -0600)]
ASoC: twl6040: Fix TLV dB step values for gains
Some gains were incorrectly configured for dB values.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Jorge Eduardo Candelaria [Sat, 11 Dec 2010 03:06:30 +0000 (21:06 -0600)]
ASoC: twl6040: Increase timeout for power up
After coming back from suspend, the timeout waiting for Phoenix
chip to complete its power up sequence is not enough, which leaves
the codec cache value for some registers in an outdated state.
Increase the timeout value to wait for the power up sequence
to correclty complete.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Misael Lopez Cruz [Sat, 11 Dec 2010 03:06:24 +0000 (21:06 -0600)]
ASoC: twl6040: Enable plug detection interrupts
Enable plug detection interrupt mask in order to get headset
PLUGINT/UNPLUGINT interrupts.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Jorge Eduardo Candelaria [Sat, 11 Dec 2010 03:06:13 +0000 (21:06 -0600)]
ASoC: twl6040: Clear interrupt status at boot time
On Phoenix 1.1, the INTID register default value is an invalid
one, causing the interrupt handler to think the phoenix power on
sequence is ready before it actually finishes.
This causes some i2c errors when trying to configure twl.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Olaya, Margarita [Sat, 11 Dec 2010 03:06:07 +0000 (21:06 -0600)]
ASoC: twl6040: Enable automatic power for phoenix 1.1
Phoenix 1.1 supports automatic power on sequence, a
verification is added to use it with new revision of
the chip.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Francois Mazard [Sat, 11 Dec 2010 03:06:03 +0000 (21:06 -0600)]
ASoC: twl6040: Fix analog Mic L & R mux controls
The mux control has 4 elements not 3
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Olaya, Margarita [Sat, 11 Dec 2010 03:05:58 +0000 (21:05 -0600)]
ASoC: twl6040: Support other sample rates.
The twl6040 can support more sample rates other than 88.2 and 96k.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Olaya, Margarita [Sat, 11 Dec 2010 03:05:54 +0000 (21:05 -0600)]
ASoC: twl6040: Fix PCM error handling ops
This patch moves all the PCM error handling for clock config
out of trigger() and startup() and into prepare().
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Olaya, Margarita [Sat, 11 Dec 2010 03:05:46 +0000 (21:05 -0600)]
ASoC: twl6040: Restore bias level at resume
This patch restores the CODEC bias level at resume().
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Jorge Eduardo Candelaria [Sat, 11 Dec 2010 03:05:32 +0000 (21:05 -0600)]
ASoC: twl6040: Add headset and handset mux controls
This patch adds support for the twl6040 headset and handset
MUX controls.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Olaya, Margarita [Sat, 11 Dec 2010 03:05:30 +0000 (21:05 -0600)]
ASoC: twl6040: Modify the IRQ handler
Multiples interrupts can be received. The irq handler is modified
to attend all of them.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Olaya, Margarita [Sat, 11 Dec 2010 03:05:24 +0000 (21:05 -0600)]
ASoC: twl6040: Update twl IO macro
Update the codec to use the new twl core register macros
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Jorge Eduardo Candelaria [Sat, 11 Dec 2010 02:45:19 +0000 (20:45 -0600)]
ASoC: sdp4430: Add Jack support
Use jack framework to enable detection for the headset microphone
and stereo output in the sdp4430.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Jorge Eduardo Candelaria [Sat, 11 Dec 2010 02:45:17 +0000 (20:45 -0600)]
ASoC: twl6040: Add jack support for headset and handset
This patch adds support for reporting twl6040 headset and
handset jack events.
The machine driver retrieves and report the status through
twl6040_hs_jack_detect.
A workq is used to debounce of the irq.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Peter Ujfalusi [Tue, 14 Dec 2010 11:45:29 +0000 (13:45 +0200)]
ASoC: TWL4030: Fix 24bit support
twl4030 series of codecs supports S32_LE with msbits=24.
Replace the S24_LE with S32_LE format, and add constraint
for 24msbit in case of 32 S32_LE format.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Peter Ujfalusi [Fri, 10 Dec 2010 11:26:31 +0000 (13:26 +0200)]
ASoC: tlv320dac33: Power down digital parts, when not needed
If the following scenario has been followed:
1. Enable analog bypass
amixer sset 'Analog Left Bypass' on
amixer sset 'Analog Right Bypass' on
2. Start playback
aplay -fdat -d3 /dev/zero
After the playback stopped (3 sec), and the soc timeout (5 sec),
the digital parts of the codec will remain powered up.
This means that the DAI clocks are continue to run, the
oscillator remain operational, etc.
Use the SND_SOC_DAPM_POST_PMD widget to get notification
about the stopped stream, and power down the digital
part of the codec.
If the analog bypass is enabled, than the codec will remain in
BIAS_ON level, and things will work correctly.
In case, if the bypass is disabled, than the codec will
fall to BIAS_STANDBY than to BIAS_OFF level, as it used
to.
The digital part of DAC33 is initialized at every stream start
(DAPM_PRE:PRE_PMU event), so subsequent streams (within 5 sec)
will have working DAI.
When the codec is coming out from BIAS_OFF, the full power-up
sequence followed by the same DAPM_PRE widget event will power up
the digital part.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Jorge Eduardo Candelaria [Wed, 8 Dec 2010 16:55:05 +0000 (10:55 -0600)]
ASoC: sdp4430: Enable FM stereo pins
Add FM stereo pins to the machine driver and add them as a
dapm widget.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Peter Ujfalusi [Wed, 8 Dec 2010 13:12:56 +0000 (15:12 +0200)]
ASoC: tlv320dac33: Fix compillation error
Fix the compilation error introduced by patch:
ASoC: tlv320dac33: Avoid multiple soft power up
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Peter Ujfalusi [Wed, 8 Dec 2010 14:04:33 +0000 (16:04 +0200)]
ASoC: tlv320dac33: Move DAC LR power on to a supply widget
The power for the DACs need to be enabled, even when only
the analog bypass is in use with the codec, otherwise
the audio is going to be distorted.
Make sure that the DACs are powered all the time, when
there is audio activity.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Peter Ujfalusi [Wed, 8 Dec 2010 14:04:32 +0000 (16:04 +0200)]
ASoC: tlv320dac33: Rename outpup amplifier widget
Use better name for the widget, and remove the 'Power'
from it's name.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Axel Lin [Wed, 1 Dec 2010 06:38:24 +0000 (14:38 +0800)]
ASoC: Remove unused aic3x_i2c_init and aic3x_i2c_exit functions
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Peter Ujfalusi [Thu, 2 Dec 2010 07:29:56 +0000 (09:29 +0200)]
ASoC: tpa6130a2: Replace DAPM code with direct interface
The use of DAPM widgets, and extra routing can cause ordering
problems in the system.
Machine drivers should use the exported direct interface with
SND_SOC_DAPM_HP's event callback to manage the state of the
amplifier.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Peter Ujfalusi [Tue, 30 Nov 2010 14:00:03 +0000 (16:00 +0200)]
ASoC: tpa6130a2: Add stereo DAPM path
New DAPM widgets, and paths to enable both channels at the
same time (for stereo output).
With this path the switch time difference can be avoided
between left and right channels.
The original DAPM paths can be still used, if only one of
TPA's output has been connected to a speaker, but for most of
the cases, switching to the stereo path is better.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Peter Ujfalusi [Tue, 30 Nov 2010 14:00:02 +0000 (16:00 +0200)]
ASoC: tpa6130a2: Use one event handler for PGA_E
Reduce the amount of duplicated code by using single
event handler for PGA_E to enable the needed channel.
Use the w->shift to pass the channel information to
the handler function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Peter Ujfalusi [Tue, 30 Nov 2010 14:00:01 +0000 (16:00 +0200)]
ASoC: tpa6130a2: Defer SW enable from power enable
Do not enable the amplifier right after the power has been
restored to the amplifier.
The DAPM_SUPPLY widget turns on the amp early in the DAPM
power walk, and the unmuting of channel happens quite late.
Keeping the amp in SW reset state ensures better muting.
In this way the pop noise coming from other components (codec)
can be filtered out.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Peter Ujfalusi [Tue, 30 Nov 2010 14:00:00 +0000 (16:00 +0200)]
ASoC: tpa6130a2: Simplify power state management
Use simpler way to avoid setting the same power state
for the amplifier.
Simplifies the check introduced by patch:
ASoC: tpa6130a2: Fix unbalanced regulator disables
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Peter Ujfalusi [Tue, 30 Nov 2010 12:31:46 +0000 (14:31 +0200)]
ASoC: tlv320dac33: Avoid multiple soft power up
During playback start the codec has been already powered at
BIAS_ON event time, so there's no need to enable the codec again.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Peter Ujfalusi [Tue, 30 Nov 2010 12:31:45 +0000 (14:31 +0200)]
ASoC: tlv320dac33: Do not enable the codec in init_chip
No need to enable the codec at this time.
The codec will be enabled later by other events
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Mon, 29 Nov 2010 18:33:47 +0000 (18:33 +0000)]
Merge branch 'for-2.6.37' into for-2.6.38
Axel Lin [Mon, 29 Nov 2010 06:55:58 +0000 (14:55 +0800)]
ASoC: Add missing dev_set_drvdata in p1022_ds_probe
Otherwise, calling dev_get_drvdata in p1022_ds_remove returns NULL.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Mon, 29 Nov 2010 06:54:58 +0000 (14:54 +0800)]
ASoC: Add missing dev_set_drvdata in mpc8610_hpcd_probe
Otherwise, calling dev_get_drvdata in mpc8610_hpcd_remove returns NULL.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Mon, 29 Nov 2010 09:43:39 +0000 (17:43 +0800)]
ASoC: Remove unneeded !! operations while checking return value of nuc900_checkready
I think this unneededd !! operations just reduce the readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Mon, 29 Nov 2010 09:40:53 +0000 (17:40 +0800)]
ASoC: Fix compile error for nuc900-pcm.c
This patch fixes below error:
CC sound/soc/nuc900/nuc900-pcm.o
sound/soc/nuc900/nuc900-pcm.c: In function 'nuc900_dma_open':
sound/soc/nuc900/nuc900-pcm.c:267: error: 'nuc900_ac97_data' undeclared (first use in this function)
sound/soc/nuc900/nuc900-pcm.c:267: error: (Each undeclared identifier is reported only once
sound/soc/nuc900/nuc900-pcm.c:267: error: for each function it appears in.)
sound/soc/nuc900/nuc900-pcm.c: At top level:
sound/soc/nuc900/nuc900-pcm.c:337: error: expected ',' or ';' before 'static'
sound/soc/nuc900/nuc900-pcm.c:354: error: 'nuc900_soc_platform_probe' undeclared here (not in a function)
make[3]: *** [sound/soc/nuc900/nuc900-pcm.o] Error 1
make[2]: *** [sound/soc/nuc900] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Mon, 29 Nov 2010 09:40:05 +0000 (17:40 +0800)]
ASoC: Fix prototype for nuc900_ac97_probe and nuc900_ac97_remove
This patch fixes below compile warning:
CC sound/soc/nuc900/nuc900-ac97.o
sound/soc/nuc900/nuc900-ac97.c:300: warning: initialization from incompatible pointer type
sound/soc/nuc900/nuc900-ac97.c:301: warning: initialization from incompatible pointer type
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Mon, 29 Nov 2010 09:39:10 +0000 (17:39 +0800)]
ASoC: Fix compile error for nuc900-ac97.c
Fix below compile error by add a missing ';'.
CC sound/soc/nuc900/nuc900-ac97.o
sound/soc/nuc900/nuc900-ac97.c:300: warning: initialization from incompatible pointer type
sound/soc/nuc900/nuc900-ac97.c:301: warning: initialization from incompatible pointer type
sound/soc/nuc900/nuc900-ac97.c:318: error: expected ',' or ';' before 'static'
sound/soc/nuc900/nuc900-ac97.c:405: error: 'nuc900_ac97_drvprobe' undeclared here (not in a function)
make[3]: *** [sound/soc/nuc900/nuc900-ac97.o] Error 1
make[2]: *** [sound/soc/nuc900] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Dimitris Papastamos [Mon, 29 Nov 2010 10:54:28 +0000 (10:54 +0000)]
ASoC: soc-cache: Ensure consistent cache naming
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Dimitris Papastamos [Mon, 29 Nov 2010 10:24:54 +0000 (10:24 +0000)]
ASoC: soc-cache: Add error checking in the *_cache_sync functions
Ensure that we report any errors encountered during reads/writes
in the cache syncing functions.
Remove redundant newline in the source code.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Fri, 26 Nov 2010 06:54:42 +0000 (14:54 +0800)]
ASoC: Fix resource leak in smdk_spdif.c
Properly free allocated resources in smdk_init() error path.
Add missing platform_device_unregister() in smdk_exit().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Fri, 26 Nov 2010 06:53:38 +0000 (14:53 +0800)]
ASoC: Add missing gpio_free(S3C64XX_GPK(12)) in smartq_exit()
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Fri, 26 Nov 2010 06:52:47 +0000 (14:52 +0800)]
ASoC: Fix resource leak in neo1973_gta02_init() error path
Properly free allocated resources in neo1973_gta02_init() error path.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Fri, 26 Nov 2010 06:51:56 +0000 (14:51 +0800)]
ASoC: Fix resource leak in goni_wm8994.c
Properly free allocated resources in goni_init() error path.
Add missing snd_soc_unregister_dai() in goni_exit().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Fri, 26 Nov 2010 17:23:43 +0000 (17:23 +0000)]
ASoC: Implement runtime PM for WM8994/58
This allows us to communicate our power management state back to the
parent device, allowing it to do a full power down when the device is
idle.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Fri, 26 Nov 2010 17:23:42 +0000 (17:23 +0000)]
ASoC: Enable rbtree compression for WM8994/58 register cache
The WM8994 and WM8958 register map is relatively sparse so benefits
from compression. The rbtree compression gives better results than
LZO for both memory and CPU consumption on a map as sparse as this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Fri, 26 Nov 2010 17:23:41 +0000 (17:23 +0000)]
ASoC: Convert WM8994 to use soc-cache.c cache functions
In the process we convert the driver to read registers one at a time
when initialising the cache. This has the effect of working around
limitations in the sizes of I2C transactions which can be done by some
CPUs. Due to the sparseness of the register map the overhead from this
should be minimual unless I2C transactions are very expensive to start.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Fri, 26 Nov 2010 15:21:09 +0000 (15:21 +0000)]
ASoC: Add WM8958 microphone detection support
The WM8958 contains an advanced accessory detection feature which allows
detection of up to seven different impedence levels on the microphone
bias output, including detection of video outputs. Since some of the
more involved accessory interfaces may involve noticable interactions
with external components a simple detection scheme is provided by
default with the option to provide custom handling of accessory detect.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Fri, 26 Nov 2010 15:21:08 +0000 (15:21 +0000)]
ASoC: Add WM8958 Multi-band compressor support
The WM8958 features a multi-band compressor which can be enabled on
any of the AIF inputs. The MBC allows different gains to be applied to
differnt audio bands, providing an improvement in perceived loudness
of the signal by avoiding overdriving the output transducers. This
patch enables support for the MBC.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Fri, 26 Nov 2010 15:21:07 +0000 (15:21 +0000)]
ASoC: Implement support for enhanced AIF3 on WM8958
Additional audio routing options are available on the WM8958 audio
interface 3. Add support for these.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Fri, 26 Nov 2010 15:21:06 +0000 (15:21 +0000)]
ASoC: Initial WM8958 audio configuration
The WM8958 is a WM8994 derivative. This patch merely ensures that some
revision specific configuration for WM8994 is not enabled on WM8994,
additional patches will add support for the new features introduced on
the WM8958.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Fri, 26 Nov 2010 17:23:44 +0000 (17:23 +0000)]
ASoC: Use DC servo startup mode when not doing DCS correction
Devices which do not have a DCS correction applied can use the explicit
DC servo startup mode for optimal startup performance. This most
immediately affects the WM8958.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Wed, 1 Sep 2010 09:47:16 +0000 (10:47 +0100)]
gpiolib: Add WM8958 support to the WM8994 driver
Several of the GPIOs on the WM8994 are fixed function on the WM8958 so
error out if the user tries to request them with gpiolib.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Tue, 31 Aug 2010 18:25:12 +0000 (19:25 +0100)]
mfd: Add initial WM8958 support
The WM8958 is a derivative of the WM8994 which is register compatible
with the addition of some extra features, mostly in the CODEC side.
The major change visible at the MFD level is that rather than a single
DBVDD supply we now have three separate DBVDDs so we must request and
enable a different set of supplies.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Fri, 26 Nov 2010 11:50:03 +0000 (11:50 +0000)]
ASoC: Remove redundant hw_write initialisation in WM8737
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Thu, 25 Nov 2010 21:16:52 +0000 (21:16 +0000)]
Merge branch 'for-2.6.37' into for-2.6.38
Axel Lin [Wed, 24 Nov 2010 14:24:01 +0000 (22:24 +0800)]
ASoC: Fix resource reclaim for osk5912
In current implementation, there are resources leak in the error path.
This patch properly reclaims the allocated resources in the error path.
Also adds a missing clk_put in osk_soc_exit.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Wed, 24 Nov 2010 14:40:59 +0000 (22:40 +0800)]
ASoC: tlv320aic3x - fix variable may be used uninitialized warning
If aic3x_read failed , val is used uninitialized.
Fix it by initializing val to 0.
This patch fixes below compile warning:
sound/soc/codecs/tlv320aic3x.c: In function 'aic3x_get_gpio':
sound/soc/codecs/tlv320aic3x.c:1183: warning: 'val' may be used uninitialized in this function
sound/soc/codecs/tlv320aic3x.c: In function 'aic3x_headset_detected':
sound/soc/codecs/tlv320aic3x.c:1211: warning: 'val' may be used uninitialized in this function
sound/soc/codecs/tlv320aic3x.c: In function 'aic3x_button_pressed':
sound/soc/codecs/tlv320aic3x.c:1219: warning: 'val' may be used uninitialized in this function
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 24 Nov 2010 15:48:01 +0000 (15:48 +0000)]
ARM: Samsung: Make sure ASoC DMA device is prototyped
Ensure that the prototype agrees with the definition and stop sparse
complaining when building the file.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Wed, 24 Nov 2010 16:27:08 +0000 (16:27 +0000)]
ASoC: Add WM8737 ALC support
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Wed, 24 Nov 2010 17:20:27 +0000 (17:20 +0000)]
ASoC: Update MAINTAINERS for Samsung driver move
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Wed, 24 Nov 2010 17:18:45 +0000 (17:18 +0000)]
ASoC: Make SMDK WM8580 driver unloadable
Supply a module exit function so that the driver can be unloaded.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Thu, 25 Nov 2010 11:17:24 +0000 (11:17 +0000)]
Merge branch 'for-2.6.37' into for-2.6.38
Axel Lin [Thu, 25 Nov 2010 07:11:45 +0000 (15:11 +0800)]
ASoC: smdk_wm9713: fix resource leak in smdk_init error path
Fix the error path to properly free allocated resources.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Thu, 25 Nov 2010 05:43:49 +0000 (13:43 +0800)]
ASoC: Fix compile error for smartq_wm8987.c
Fix below compile error:
CC sound/soc/samsung/smartq_wm8987.o
sound/soc/samsung/smartq_wm8987.c: In function 'smartq_hifi_hw_params':
sound/soc/samsung/smartq_wm8987.c:42: error: 'struct snd_soc_pcm_runtime' has no member named 'dai'
sound/soc/samsung/smartq_wm8987.c:43: error: 'struct snd_soc_pcm_runtime' has no member named 'dai'
sound/soc/samsung/smartq_wm8987.c: In function 'smartq_wm8987_init':
sound/soc/samsung/smartq_wm8987.c:192: warning: passing argument 1 of 'snd_soc_jack_new' from incompatible pointer type
sound/soc/samsung/smartq_wm8987.c: At top level:
sound/soc/samsung/smartq_wm8987.c:216: warning: initialization from incompatible pointer type
make[3]: *** [sound/soc/samsung/smartq_wm8987.o] Error 1
make[2]: *** [sound/soc/samsung] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Thu, 25 Nov 2010 08:50:56 +0000 (16:50 +0800)]
ASoC: neo1973_gta02_wm8753: fix wrong parameter for snd_soc_register_dai and snd_soc_unregister_dai
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Thu, 25 Nov 2010 03:33:14 +0000 (11:33 +0800)]
ASoC: davinci-vcif - fix a memory leak
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Thu, 25 Nov 2010 07:14:03 +0000 (15:14 +0800)]
ASoC: phycore-ac97: fix resource leak
Fix imx_phycore_init() error path and imx_phycore_exit() to properly free
allocated resources.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Thu, 25 Nov 2010 07:13:09 +0000 (15:13 +0800)]
ASoC: imx-ssi: fix resource leak
Fix imx_ssi_probe() error path and imx_ssi_remove() to properly free
allocated resources.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Thu, 25 Nov 2010 07:12:30 +0000 (15:12 +0800)]
ASoC: simone: fix resource leak in simone_init error path
Fix the error path to properly free allocated resources.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Thu, 25 Nov 2010 07:11:03 +0000 (15:11 +0800)]
ASoC: sam9g20_wm8731: fix resource leak in at91sam9g20ek_init error path
Fix the error path to properly free allocated resources.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Thu, 25 Nov 2010 02:44:59 +0000 (10:44 +0800)]
ASoC: snd-soc-
afeb9260: remove unneeded platform_device_del in error path
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Thu, 25 Nov 2010 07:08:31 +0000 (15:08 +0800)]
ASoC: pcm030-audio-fabric: fix resource leak in pcm030_fabric_init error path
Add missing platform_device_put() if platform_device_add() failed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Thu, 25 Nov 2010 07:07:25 +0000 (15:07 +0800)]
ASoC: efika-audio-fabric: fix resource leak in efika_fabric_init error path
Add missing platform_device_put() if platform_device_add() failed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Thu, 25 Nov 2010 09:23:55 +0000 (17:23 +0800)]
ASoC: Call snd_soc_unregister_dais instead of snd_soc_unregister_dai in sh4_soc_dai_remove
We call snd_soc_register_dais() in sh4_soc_dai_probe(),
thus we should call snd_soc_unregister_dais() in sh4_soc_dai_remove().
Otherwise, we got "too many arguments to function 'snd_soc_unregister_dai'"
error message.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Dmitry Artamonow [Wed, 24 Nov 2010 21:46:15 +0000 (00:46 +0300)]
ASoC: fix SND_PXA2XX_LIB Kconfig warning
Fix following warning observed when SND_PXA2XX_SOC is set and SND_ARM isn't:
warning: (SND_PXA2XX_AC97 && SOUND && !M68K && SND && SND_ARM && ARCH_PXA ||
SND_PXA2XX_SOC && SOUND && !M68K && SND && SND_SOC && ARCH_PXA) selects
SND_PXA2XX_LIB which has unmet direct dependencies (SOUND && !M68K && SND &&
SND_ARM)
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 24 Nov 2010 11:57:43 +0000 (11:57 +0000)]
Merge branch 'for-2.6.37' into for-2.6.38
Mark Brown [Tue, 23 Nov 2010 19:31:18 +0000 (19:31 +0000)]
ASoC: Add initial WM8737 driver
The WM8737 is a low power, flexible stereo ADC designed for portable
applications. This driver supports most of the functionality of the
WM8737, though some features such as the ALC are not yet implemented.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Wed, 24 Nov 2010 08:44:23 +0000 (16:44 +0800)]
ASoC: nuc900-ac97: fix a memory leak
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 24 Nov 2010 11:26:39 +0000 (11:26 +0000)]
Merge branch 'topic/asoc' of git://git./linux/kernel/git/tiwai/sound-2.6 into for-2.6.38
Mark Brown [Wed, 24 Nov 2010 11:22:55 +0000 (11:22 +0000)]
Merge branch 'fix/asoc' of git://git./linux/kernel/git/tiwai/sound-2.6 into for-2.6.37
Axel Lin [Wed, 24 Nov 2010 07:20:48 +0000 (15:20 +0800)]
ASoC: Return proper error for omap3pandora_soc_init
Return PTR_ERR(omap3pandora_dac_reg) instead of 0 if regulator_get failed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Wed, 24 Nov 2010 02:21:54 +0000 (10:21 +0800)]
ASoC: wm8961 - clear WM8961_MCLKDIV bit for freq <=
16500000
MCLKDIV bit of Register 04h Clocking1:
0 : Divide by 1
1 : Divide by 2
Thus in the case of freq <=
16500000, we should clear MCLKDIV bit.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Axel Lin [Wed, 24 Nov 2010 02:20:33 +0000 (10:20 +0800)]
ASoC: wm8961 - clear WM8961_DACSLOPE bit for normal mode
DACSLOPE bit of Register 06h ADC and DAC Control 2:
0: Normal mode
1: Sloping stop-band mode
Thus in the case of normal mode, we should clear DACSLOPE bit.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Mark Brown [Tue, 23 Nov 2010 14:30:41 +0000 (14:30 +0000)]
Merge branch 'for-2.6.37' into for-2.6.38
Axel Lin [Tue, 23 Nov 2010 07:58:39 +0000 (15:58 +0800)]
ASoC: wm8994 - fix memory leaks
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Tue, 23 Nov 2010 07:57:49 +0000 (15:57 +0800)]
ASoC: wm8904 - fix memory leaks
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Tue, 23 Nov 2010 07:56:21 +0000 (15:56 +0800)]
ASoC: max98088 - fix a memory leak
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Tue, 23 Nov 2010 06:14:07 +0000 (14:14 +0800)]
ASoC: Do not update the cache if write to hardware failed
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jesper Juhl [Mon, 22 Nov 2010 21:54:03 +0000 (22:54 +0100)]
ASoC: MPC5200: Eliminate duplicate include of of_device.h
Eliminate duplicate #include <linux/of_device.h> from
sound/soc/fsl/mpc5200_dma.c
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jassi Brar [Mon, 22 Nov 2010 06:37:25 +0000 (15:37 +0900)]
ASoC: Samsung: Rename from s3c24xx to samsung
Finally, move the 's3c24xx' directory to 'samsung'
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jassi Brar [Mon, 22 Nov 2010 06:37:22 +0000 (15:37 +0900)]
ASoC: Samsung: Generalize Kconfig symbols
Move prefixes to repesent the nature of Samsung ASoC suitably.
SND_S3C24XX_SOC -> ASOC_SAMSUNG
SND_S3C_SOC_PCM -> SND_SAMSUNG_PCM
SND_S3C_SOC_AC97 -> SND_SAMSUNG_AC97
SND_S5P_SOC_SPDIF -> SND_SAMSUNG_SPDIF
SND_S3C24XX_SOC_I2S -> SND_S3C24XX_I2S
SND_S3C64XX_SOC_SMARTQ -> ASOC_SMARTQ
SND_SOC_SMDK_SPDIF -> ASOC_SAMSUNG_SMDK_SPDIF
SND_SOC_SMDK_WM8580 -> ASOC_SAMSUNG_SMDK_WM8580
SND_SOC_SMDK_WM9713 -> ASOC_SAMSUNG_SMDK_WM9713
SND_SOC_GONI_AQUILA_WM8994 -> ASOC_GONI_AQUILA_WM8994
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jassi Brar [Mon, 22 Nov 2010 06:37:19 +0000 (15:37 +0900)]
ASoC: SMDK_WM8580: Enable for SMDKC100
Enable the ASoC Machine driver to run on SMDKC100 as well.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jassi Brar [Mon, 22 Nov 2010 06:37:16 +0000 (15:37 +0900)]
ASoC: SMDK64XX: Rename for other platforms
We plan to use the same ASoC Machine driver for most of
latest SMDK platforms. So rename the 64XX specific driver
to generic named.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jassi Brar [Mon, 22 Nov 2010 06:37:13 +0000 (15:37 +0900)]
ASoC: S3C64XX: Remove obsoleted I2S drivers
Now that we have better I2S CPU drivers and no need for the old
ones, discard them.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jassi Brar [Mon, 22 Nov 2010 06:37:07 +0000 (15:37 +0900)]
ASoC: SMDK64XX: Move to use new I2S driver
Modify the smdk64xx_wm8580.c to use new i2s controller driver.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jassi Brar [Mon, 22 Nov 2010 06:37:04 +0000 (15:37 +0900)]
ASoC: GONI: Move to use new I2S driver
Modify the goni_wm8994.c to use new i2s controller driver.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jassi Brar [Mon, 22 Nov 2010 06:37:02 +0000 (15:37 +0900)]
ASoC: SMARTQ: Move to use new I2S driver
Modify the smartq_wm8987.c to use new i2s controller driver.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jassi Brar [Mon, 22 Nov 2010 06:36:59 +0000 (15:36 +0900)]
ASoC: Samsung: Add common I2S driver
The I2S controllers since S3C64XX are incremental revisions, with
a new feature added to the last one. The programming i/f doesn't
conflict between these revisions, so it is possible to have one
common driver that could manage various versions of I2S (v3, 4 & 5)
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jassi Brar [Mon, 22 Nov 2010 06:36:54 +0000 (15:36 +0900)]
ASoC: Samsung: Rename s3c64xx I2S device
Since the I2S of S3C64XX and newer SoCs are incremental
versions of each other with changes managable in a single
driver, rename the 's3c64xx-iis' -> 'samsung-i2s'
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
projects / GitHub / MotorolaMobilityLLC / kernel-slsi.git / log