ath9k: update hw configuration for virtual wiphys

ath9k supports its own virtual wiphys. The hardware code
relies on the ieee80211_hw for the present interface but
with recent changes introduced the common->hw was never
updated and is required for virtual wiphys.

Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix listening to idle requests

The way idle configuration detection was implemented as
busted due to the fact that it assumed the ath9k virtual wiphy,
the aphy, would be marked as inactive if it was not used but
it turns out an aphy is always active if its the only wiphy
present. We need to distinguish between aphy activity and
idleness so we now add an idle bool for the aphy and mark
it as such based on the passed IEEE80211_CONF_CHANGE_IDLE
from mac80211.

Previous to all_wiphys_idle would never be true when using
only one device so we never really were using
IEEE80211_CONF_CHANGE_IDLE -- we never turned the radio
off or on upon IEEE80211_CONF_CHANGE_IDLE changes as radio
changes depended on all_wiphys_idle being true either to
turn the radio on or off. Since it was always false for
one device this code was doing nothing.

Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Reported-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: implement support for 4-address frames for AP and client mode

In some situations it might be useful to run a network with an
Access Point and multiple clients, but with each client bridged
to a network behind it. For this to work, both the client and the
AP need to transmit 4-address frames, containing both source and
destination MAC addresses.
With this patch, you can configure a client to communicate using
only 4-address frames for data traffic.
On the AP side you can enable 4-address frames for individual
clients by isolating them in separate AP VLANs which are configured
in 4-address mode.
Such an AP VLAN will be limited to one client only, and this client
will be used as the destination for all traffic on its interface,
regardless of the destination MAC address in the packet headers.
The advantage of this mode compared to regular WDS mode is that it's
easier to configure and does not require a static list of peer MAC
addresses on any side.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211: add a parameter for using 4-address frames on virtual interfaces

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: improve peer link management debugging

Print the FSM state strings instead of just the numbers.

Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: improve HWMP debugging

Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: allow processing of more than one HWMP IE

Since the HWMP IEs are now all optional and the action code is fixed,
allow the HWMP code to find and process each IE on the path
selection action frames.

Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <rpaulo@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add MAC80211_VERBOSE_MHWMP_DEBUG

Add MAC80211_VERBOSE_MHWMP_DEBUG, a debugging option for HWMP
frame processing.

Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: update the format of path selection frames

Update the format of path selection frames according to latest
draft (3.03).

Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: update peer link management IE and action frames

Update the length and format of the peer link management action frames.

Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix typo in a comment

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: implement the meshconf formation info field

The Mesh Configuration Formation Info field contains the number of
neighbors.  This means that the beacon must be updated every time a
peer joins or leaves.

Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <rpaulo@gmail.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: set MESH_TTL to 31

Update the mesh time to live field to 31 according to draft 3.03.

Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: update meshconf IE

This updates the Mesh Configuration IE according to the latest
draft (3.03).
Notable changes include the simplified protocol IDs.

Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix building of rt2800lib when rt2x00 driver is built-in.

When enabling rt2800usb as a built-in driver (as opposed to a as a module) the build fails. See
http://marc.info/?l=linux-wireless&m=125768687711034&w=2 for details.

Fix it by properly including <linux/usb.h> from rt2x00usb.h

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Move interface type assignments to generic code.

Make sure all drivers can benefit of the assignment of the interface
type of an adapter, instead of keeping it for rt2800 only.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless: correct check on CCS_START_NETWORK

CCS_START_NETWORK is declared in drivers/net/wireless/rayctl.h with the
comment Values for cmd.  status is previously compared to
CCS_COMMAND_COMPLETE, which is declared in the same file with the comment
Values for buffer_status.  Finally, it is possible at this point that cmd
is CCS_START_NETWORK, because it is compared to that value in an enclosing
switch that has CCS_START_NETWORK as one of two case labels around this code.

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

zd1211rw: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

zd1201: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl12xx: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

prism54: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas_tf_usb: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ipw2200: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ipw2100: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

atmel: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

at76c50x-usb: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43-pio: Fix RX error path for rev>=8 devices

This fixes the RX error path for rev>=8 devices.
The wrong register size and definitions were used.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

staging/wireless: don't build when NET etc. are not enabled

These wireless drivers in staging could be built when
CONFIG_NET=n, CONFIG_NETDEVICES=n, causing this build error:

net/wireless/wext-priv.c: In function 'ioctl_private_call':
net/wireless/wext-priv.c:206: error: implicit declaration of function 'call_commit_handler'

due to faulty selects.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: MAC_ACCESS_REQ cleanup

Add txq_id info to "Tx queue requesting wakeup" debug message

Add "Rx queue requesting wakeup" debug message

Move clear of CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ to be after nearby
iwl_write_prph(), since iwl_write_prph() sets it and clears it.  Almost
removed it entirely, but just making sure in case someone removes the
iwl_write_prph()!  Also remove unneeded priv->lock usage; this is now
handled by priv->reg_lock within iwl_clear_bit().

Join a couple of lines that had unneeded line returns.

Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: Fix issue on file transfer stalled in HT mode

Turn on RTS/CTS for HT to prevent uCode TX fifo underrun

This is fix for
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2103

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Jiajia Zheng <jiajia.zheng@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: update write pointers in iwl_irq_tasklet()

Follow-up to "update write pointers for all tx queues after wakeup"; that
patch changed iwl_irq_tasklet_legacy(), but not iwl_irq_tasklet(), so
newer devices were not covered.

Comments from original patch:

Wakeup interrupt has been updating write pointers (indexes, actually) only
for tx queues 0-5.  This is adequate just for 3945, but inadequate for other
devices, all of which have more tx queues.  Now updating all tx/command queues,
so device can be aware of all new tx and host commands enqueued while
device was asleep.

This can potentially improve data traffic bandwidth and/or latency.

Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: Add comments about MAC_ACCESS_REQ

Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: Update comments for struct iwl_ssid_ie

Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: speed up event log dumps

Take advantage of device's auto-increment for SRAM reads to eliminate extra
write address accesses.

Grab/release NIC access before/after entire read sequence, rather than for
each read individually.

After a quick check of dmesg logs, this seems to double Event Log dump speed,
reducing from about 20 milliseconds to about 10 milliseconds for 512 entries
using 3945.

Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: Limit size of Event Log dump

If device provides bad values for Event Log parameters (due to being asleep
or SRAM corruption, etc.), the size can be very, very large (e.g. 0xa5a5a5a5),
which can flood system log.

Sanity-check capacity and next_entry values and limit to reasonable size dump.

Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: do not base station's sm_ps setting on AP

Do not use AP's SM_PS setting for our own SM_PS setting.

Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: drop non-production PCI-IDs

Remove the support for all the PCI_IDs never make into production

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix for channel switch

Different channel has different configuration, need to pass correct
configuration to uCode when send "channel switch" command to uCode.
Invalid configuration will cause sysassert in uCode and produce
un-expected result.

Even it is a very small windows, but we also need to consider and handle
the case if commit_rxon occurred before the "channel switch
announcement" notification received from uCode.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: add FIFO usage for 5000

This is part of the code, but the comment doesn't have it,
add pointers to the code and the FIFO usage for 5000 and
up.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: remove un-used parameter

Remove un-used parameter "recovery_rxon" from "priv" data structure

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix FIFO vs. queue confusion

When I added that code setting the swq_id, I evidently
did not understand the distinction between FIFO and TX
queue yet and added code to compare a queue ID and a
FIFO number, which is bogus.

However, the code there need not be this specific, it
can just set all queues to the identity mapping which
will be overwritten by the aggregation queue code. As
a bit of defensive coding, don't assign an swq_id to
the command queue so that if we ever use it for frames
we notice quickly.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: don't double-activate queue 4

The fourth queue (command queue) is already activated in
the loop above that also maps it to the command FIFO and
therefore doesn't need to be marked as activated again.
Also change the TODO comment to be accurate -- we need
to initialise the _queues_, not FIFOs, and map them to
device FIFOs.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: no periodic Tx/IQ calibration for 6x00/6x50 series

For both 6x00 and 6x50 series devices, periodic Tx IQ calibration is
disabled in uCode, driver do not need to set the periodic Tx/IQ calibration
bit in calibration command.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: use configured valid rx chain for scan

Use configured valid rx chains in scan command instead of ANT_ABC, correcting
valid rx chain configuration of 4965, should be ANT_ABC instead of ANT_AB.

Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: use only one chain for scan in PS

When doing scan in power saving mode, choose only 1 valid RX chain instead of
turning all chains on.

Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: print rx_on config to help debug

To help debug rx related issues, if IWL_DEBUG_RADIO flag is set, print
the rxon configuration when rxon host command send to uCode.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: allocate 128 bytes linear buffer for rx skb

Allocate 128 bytes linear buffer for rx skb. The first 64 bytes is
reserved for mac80211 usage (for radiotap header expansion, etc).
The frame header starts from the second 64 bytes.

Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: change debug message to error in failure case

Since these messages indicate failure we would be interested in seeing them
always.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Rewrite TX bounce buffer handling

Do not mess with the original skb, but allocate an independent bouncebuffer.
This protects against bad interference with mac80211's assumptions about
the skb (which already caused bugs).

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of /linux/kernel/git/davem/net-2.6

Conflicts:
drivers/net/wireless/iwlwifi/iwl-1000.c
drivers/net/wireless/iwlwifi/iwl-6000.c
drivers/net/wireless/iwlwifi/iwl-core.h

CAN: use dev_get_by_index_rcu

Use new function to avoid doing read_lock().

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPV4: use rcu to walk list of devices in IGMP

This also needs to be optimized for large number of devices.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

decnet: use RCU to find network devices

When showing device statistics use RCU rather than read_lock(&dev_base_lock)
Compile tested only.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390: use RCU to walk list of network devices

This is similar to other cases where for_each_netdev_rcu
can be used when gathering information.

By inspection, don't have platform or cross-build environment
to validate.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: use rcu for network scheduler API

Use RCU to walk list of network devices in qdisc dump.
This could be optimized for large number of devices.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vlan: eliminate use of dev_base_lock

Do not need to use read_lock(&dev_base_lock), use RCU instead.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netdev: add netdev_continue_rcu

This adds an RCU macro for continuing search, useful for some
network devices like vlan.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPv6: use ipv6_addr_v4mapped()

Change udp6_portaddr_hash() to use ipv6_addr_v4mapped()
inline instead of ipv6_addr_type().

Signed-off-by: Brian Haley <brian.haley@hp.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

parisc: led: Use for_each_netdev_rcu()

Use for_each_netdev_rcu() and dont lock dev_base_lock anymore

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sit: Clean up DF code by copying from IPIP

This patch rearranges the SIT DF bit handling using the new IPIP DF
code.  The only externally visible effect should be the case where
PMTU is enabled and the MTU is exactly 1280 bytes.  In this case the
previous code would send packets out with DF off while the new code
would set the DF bit.  This is inline with RFC 4213.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thanks,
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Allow inet6_dump_addr() to handle more than 64 addresses

Apparently, inet6_dump_addr() is not able to handle more than
64 ipv6 addresses per device. We must break from inner loops
in case skb is full, or else cursor is put at the end of list.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: speedup inet6_dump_ifinfo()

When handling large number of netdevice, inet6_dump_ifinfo()
is very slow because it has O(N^2) complexity.

Instead of scanning one single list, we can use the 256 sub lists
of the dev_index hash table, and RCU lookups.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: netlink_getname, packet_getname -- use DECLARE_SOCKADDR guard

Use guard DECLARE_SOCKADDR in a few more places which allow
us to catch if the structure copied back is too big.

Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

usbnet: Set link down initially for drivers that update link state

Some usbnet drivers update link state while others do not due to
hardware limitations.  Add a flag to distinguish those that do, and
set the link down initially for their devices.

This is intended to fix this bug: http://bugs.debian.org/444043

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

niu: Use DMA_BIT_MASK(44) instead of deprecated DMA_44BIT_MASK

Use DMA_BIT_MASK(44) instead of deprecated DMA_44BIT_MASK

Signed-off-by: Marin Mitov <mitov@issp.bas.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

udp: bind() optimisation

UDP bind() can be O(N^2) in some pathological cases.

Thanks to secondary hash tables, we can make it O(N)

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: version 1.52.1-4

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Change coalescing granularity to 4us

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Remove misleading error print

Failing to allocate MSI-X vectors is not an error and should not be
printed as such

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: GSO implies CSUM offload

Making sure that whenever the FW/HW is configured for GSO, it is also
configured to CSUM offload

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Phonet: allocate and copy for pipe TX without sock lock

Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Phonet: put sockets in a hash table

Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

speedfax: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

pcnet-cs: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

tms380tr: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

spider-net: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

myri10ge: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb3: declare MODULE_FIRMWARE

Replace run-time string formatting with preprocessor string
manipulation.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: declare MODULE_FIRMWARE

Replace run-time string formatting with preprocessor string
manipulation.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ambassador: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

solos-pci: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

netx: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

iwlwifi: Fix issue on file transfer stalled in HT mode

Turn on RTS/CTS for HT to prevent uCode TX fifo underrun

This is fix for
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2103

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Jiajia Zheng <jiajia.zheng@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: Use RTS/CTS as the preferred protection mechanism for 6000 series

When 802.11g was introduced, we had RTS/CTS and CTS-to-Self protection
mechanisms. In an HT Beacon, HT stations use the "Operating Mode" field
in the HT Information Element to determine whether or not to use
protection.

The Operating Mode field has 4 possible settings: 0-3:
Mode 0: If all stations in the BSS are 20/40 MHz HT capable, or if the
BSS is 20/40 MHz capable, or if all stations in the BSS are 20 MHz HT
stations in a 20 MHz BSS
Mode 1: used if there are non-HT stations or APs using the primary or
secondary channels
Mode 2: if only HT stations are associated in the BSS and at least one
20 MHz HT station is associated.
Mode 3: used if one or more non-HT stations are associated in the BSS.

When in operating modes 1 or 3, and the Use_Protection field is 1 in the
Beacon's ERP IE, all HT transmissions must be protected using RTS/CTS or
CTS-to-Self.

By default, CTS-to-self is the preferred protection mechanism for less
overhead and higher throughput; but using the full RTS/CTS will better
protect the inner exchange from interference, especially in
highly-congested environment.

For 6000 series WIFI NIC, RTS/CTS protection mechanism is the
recommended choice for HT traffic based on the HW design.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Libertas: fix issues while configuring host sleep using ethtool wol

Configuration of wake-on-lan for unicast, multicast, broadcast, physical
activity was not working. Kernel panic issue was there when user tries to
disable WOL. Fixed them.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Libertas: coding style cleanup in ethtool.c

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8187: Fix sparse warnings

Due to a missing header include, sparse generates the following warnings:

  CHECK   drivers/net/wireless/rtl818x/rtl8187_rfkill.c
warning: symbol 'rtl8187_rfkill_init' was not declared. Should it be static?
warning: symbol 'rtl8187_rfkill_poll' was not declared. Should it be static?
warning: symbol 'rtl8187_rfkill_exit' was not declared. Should it be static?

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: add LED definition for BenQ Joybook R55v

Setup the GPIOs for the BenQ Joybook netbook.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: add LED support for HP Compaq CQ60

Add GPIO configuration for the Compaq CQ60 laptop

Reported-by: David Dreggors <ddreggors@jumptv.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: don't reset mcast filter when configuring the mode

We should not zero out the multicast hash when configuring
the operating mode, since a zero value means all multicast
frames will get dropped.  Also, ath5k_mode_setup() gets
called after any reset, so the hash already set up in
configure_filter() is lost.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: update MAINTAINERS

Although I have always been the active maintainer of the rt2x00 drivers,
I was not mentioned explicitely in the MAINTAINERS file as such.

Update the rt2x00 entry in the MAINTAINERS file to add my name and
email address.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: work around a locking issue in ->set_tim()

ops->set_tim() must be atomic, so b43 trying to acquire a mutex leads
to a kernel crash. This patch trades an easy to trigger crash in AP
mode for an unlikely race condition. According to Michael, the real
fix would be to allow set_tim() to sleep, since b43 is not the only
driver that needs to sleep in all callbacks.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb-pcmcia: Fix 32bit register access in early bus scanning

The scan function was using 32 bit access which does not
work on 16bit CF cards.

This patch corrects this by doing two 16 bit reads like
ssb_pcmcia_read32 already does.

mb -- Removed locking. That early in init there's no need for locking.

Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next-2.6

Merge branch 'master' of /linux/kernel/git/davem/net-2.6

Conflicts:
drivers/net/can/usb/ems_usb.c

xfrm: SAD entries do not expire correctly after suspend-resume

  This fixes the following bug in the current implementation of
net/xfrm: SAD entries timeouts do not count the time spent by the machine
in the suspended state. This leads to the connectivity problems because
after resuming local machine thinks that the SAD entry is still valid, while
it has already been expired on the remote server.

  The cause of this is very simple: the timeouts in the net/xfrm are bound to
the old mod_timer() timers. This patch reassigns them to the
CLOCK_REALTIME hrtimer.

  I have been using this version of the patch for a few months on my
machines without any problems. Also run a few stress tests w/o any
issues.

  This version of the patch uses tasklet_hrtimer by Peter Zijlstra
(commit 9ba5f0).

  This patch is against 2.6.31.4. Please CC me.

Signed-off-by: Yury Polyanskiy <polyanskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>