ath9k_hw: Fix radio programming for AR9550

For AR9550, program the synth value based on the ref. clock.
The logic for AR9550 is similar to AR9330, but keep the code
separate since changes for AR9330 are required - which would be
done later.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Add TempCompensation feature for AR9550

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Update initvals for QCA955x

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Wake up queues in mwl8k_start

If queues are stopped in mwl8k_stop,
these should be started in mwl8k_start

Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Delete ampdu streams with state AMPDU_STREAM_NEW in sta remove

When a station deauths, we do not delete the streams with state
AMPDU_STREAM_NEW and these remain created forever. Fix this issue by
removing such streams in the driver

Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Disable tx_wait completion

Whenever TX ring is drained, priv->tx_wait still points
to a valid completion. Making sure that it points to
NULL before returning from the  mwl8k_tx_wait_empty
check.

Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Use helper routines to simplify ar9003_hw_init_cal()

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix MCI init for AGC calibration

When AGC calibration is to be done, a GPM message with the
payload, MCI_GPM_WLAN_CAL_REQ has to be sent. Currently this falls
within the IQ-CAL code block which is incorrect. Fix this by using
a separate variable to decide when IQ-CAL is to be done separately
and call ar9003_mci_init_cal_req correctly.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Do not enable IQ-CAL for half/quarter rates

IQ calibration doesn't complete and times out for half/quarter
rates, so skip it correctly.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: add place for serial flash driver

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-john' of git://git.sipsolutions.net/mac80211-next

regulatory: fix restore_regulatory_settings

My commit 379b82f4c9dc6e67bf61aa61b096c06a2f320f60
("regulatory: pass new regdomain to reset function")
broke the restore_regulatory_settings() function due
to a logic change. Consider this change:

- reset_regdomains(true);
- cfg80211_regdomain = cfg80211_world_regdom;
+ reset_regdomains(true, cfg80211_world_regdom);

This looks innocent enough, until you realise that the
called function (reset_regdomains) also resets the
cfg80211_world_regdom pointer, so that the old version
of the code would use the new object it pointed to and
the new version of the code uses the old object. This
lead to a double-free of this object.

Since reset_regdomains() sets it to &world_regdom, use
that directly.

Reported-by: Sujith Manoharan <sujith@msujith.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
Reported-by: Bob Copeland <me@bobcopeland.com>
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

regulatory: fix uevent

The uevent callback doesn't protect its access to
last_request, which now causes a warning since
the conversion to get_last_request(). Fix this by
allowing to use RCU protection for last_request.

Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mwifiex: use map/unmap APIs in TX and RX to reduce memcpy

This patch is an enhacement to mwifiex_pcie driver to use
map/unmap PCI memory APIs. This reduces one memcpy each in TX
path and RX path, and enhances throughput.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: flush TX ring for PCIe after disconnect or bss stop

This patch adds handler to clean PCIe TX rings after disconnect
or bss stop is called for PCIe based mwifiex driver.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: use pci_alloc/free_consistent APIs for PCIe

This patch uses pci_alloc_consistent and pci_free_consistent
APIs for mwifiex_pcie driver. Consistent DMA memory is allocated
for TX, RX and event rings. Command buffer and command response
buffer also uses map/unmap memory APIs to download commands and
get command responses.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: add init_fw_port handler for PCIe interface

This patch adds support for init_fw_port handler for PCIe
interface, which resets RXBD read pointer for PCIe.
This fixes issue where RX doesn't work until some TX from
driver happens.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: access interrupt status only while holding lock

This patch fixes a bug for few instances where PCIe interrupt
status variable is accessed without holding spin lock.
This can result into missing interrupts.

Fix this by copying interrupt status to a local variable and
then using it for calling specific routine.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: mips: rename oldirqflag to irqinitmask

The new name better matches the use of this variable.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: mips: remove assigned_irqs from structure

This member is not needed any more.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: mips: show also disabled IRQs

Some cores do not have a IRQ assigned and some do not support when an
IRQ is assigned to them, this is now handled and printed out in the
code.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: mips: make some info messages debug messages

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: mips: explicit assign IRQ numbers

The assignment of the IRQs to the cores of the chips by iterating over
the cores is complicated and causes problems with SoC like the BCM4706
with two GMAC core where just one should get a dedicated IRQ number.
Now the code assigns the same IRQs to the cores as the code from the
Broadcom SDK does. If the SoC is not know the current assigned IRQs are
only read out and an error message is printed.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: make bcma_find_core_unit() accessible

This bcma_find_core_unit() is needed by the mips driver in the next
patch.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix calibration for AR9340

TX_IQ_ON_AGC_CAL should not be enabled for AR9340. TX-IQ calibration
is run as part of AGC calibration only for AR9485, AR9462 and AR9565.
For the others (AR9300, AR9330, AR9340), TX-IQ cal is done independent
of AGC-cal.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: bump firmware API to 3

New firmware is required to support
a) Add support for additional ampdu streams
b) Handle corresponding watchdog events to destroy ampdu streams

Bumping firmware API version by one.

Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Handle watchdog event with highest prioriry

Currently, command path waits till all the tx host queues
are empty. Whenever watchdog event is raised, firmware
expects driver to destroy ampdu queues immediately.

This requires corresponding commands i.e.
mwl8k_cmd_get_watchdog_bitmap and mwl8k_destroy_ba to be
sent without waiting for the tx queues to be completely
empty.

Use "watchdog_event_pending" to ensure the above mentioned
two commands are sent down immediately.

Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Handle Watchdog events for the new ampdu streams

With more ampdu streams, we need to handle watchdog
events for the new ampdu streams. Handle these
events appropriately.

Earlier mwl8k_cmd_get_watchdog_bitmap used to return
only one stream index and hence bitwise operations
on the return value were not required. Now the function
returns a bitmap with different bits are mapped with
different stream indices.

Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: changing mwl8k_destroy_ba prototype

Currently, mwl8k_ampdu_stream is passed as one of the
argument to the function mwl8k_destroy_ba. Instead of
this pass only the stream index. This will be helpful
during watchdog event handling when bitmap of stream
indices are received.

Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Enable support to support additional ampdu streams

Currently, we have 2 ampdu streams that can be created
simultaneously. Firmware is capable of supporting
additional streams. Add support to use these streams.

Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: set ack policy to normal

Set ACK policy to NORMAL when its not going to
be an AMPDU packet.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Remove redundant txq_idx

Ampdu stream index can be derived from stream->idx.
So we no longer need stream->txq_idx, hence removing it.

Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Remove TEMP_COMP_CAL

This is not enabled for any chip and is unused.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Enable calibration types in init_cal_settings

Doing this in ath9k_hw_fill_cap_info() is odd and it's
cleaner to do this in the init function for calibration.
Also, setup the supported calibration type in init_cal_settings.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: parse WMM IEs from hostapd for mwifiex AP

This patch adds support for parsing WMM IEs from hostapd
and setting them to FW via sys configure command.

Patch also sets wiphy flag to advertise AP uAPSD support.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: use correct htcapinfo for HT20 ibss network

It is observed that same htcapinfo ie is included in beacon for
HT20, HT40+ and HT40- ibss networks. This patch makes sure that
we will not advertise 40Mhz flags while creating/joining ibss
network in HT20 mode.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: mwifiex: remove unreachable paths

We know 'firmware' is non-NULL from the beginning of mwifiex_prog_fw_w_helper,
remove all !firmware paths from the rest of the function.

Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54pci: don't return zero on failure paths in p54p_probe()

If pci_set_dma_mask() or pci_set_consistent_dma_mask() fails in p54p_probe(),
it breaks off initialization, deallocates all resources, but returns zero.
Similar issue is if check for returned value of pci_resource_len() fails.

The patch implements proper error code propagation.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: Update init code routines from interface up.

On interface up dongle gets inialized. Move UP command to common
routine and update these common init routines using ifp.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: Removing obsolete variables and inline functions.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: Return correct error on netdev xmit.

Netdev xmit routine brcfm_netdev_start_xmit was defined
incorrectly and used wrong return codes. Always eat the
packet and return ok. Remove drvr_up check since it is not
relevant.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: Remove unused caching dongle error.

CDC errors are retained. However, it is never used so it can
be removed.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove unnecessary curly braces in dhd_attach()

Stumbled into a curly braces used for if statement with only
one conditional statement. Removing them.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: cleanup netdev transmit callback

The header of the ethernet packet is processed conditionally, but
the check is wrong as it checks skb length is at least ETH_ALEN. It
should check it is at least sizeof struct ethhdr instead.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove unused event related definitions

The driver had some global definitions in dhd.h to map event
identifiers to event names. With redesign of firmware event
processing this has all moved to fweh module so these definitions
can be removed.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: Use dedicated trace level for CDC.

CDC debug is partly done with TRACE and partly with CTL, however
CDC hardly ever needs debugging. Use dedicated level CDC and
replace TRACE and CTL in dhd_cdc with that.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove brcmf_proto_hdrpull() from bus interface

The use of the function brcmf_proto_hdrpull() is moved to the
common part of the driver and consequently it can be removed
from the bus interface.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove rx helper function from bus interface

The bus interface provided a wrapper function to pass a single
packet to the common driver part filling a skb queue with one
packet. For clarity the caller now sets up the skb queue and
call the rx bus interface function.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: define pr_fmt in one place

Several source files (but not all) define the pr_fmt() macro in exactly
the same way. Instead this commit defines it in a header file so driver
logging is consistent.

Cc: Joe Perches <joe@perches.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: assure USB dongle firmware is reset upon module unload

Upon unloading the brcmfmac module the USB firmware should be reset
as the device remains powered. The reset assures a known device
state when a new brcmfmac driver load is being done.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: removed deprecated set_bitrate_mask support

Set bitrate_mask is not desired anymore. The firmware will
determine the correct rates to be used.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: do not reconfigure refill rx on 0-length packet.

When USB device gets removed rx complete comes with 0-length
packets. Do not refill those packets. In some rare cases it can
cause infinite loop.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: remove dead code

Dead code after AMPDU restructure.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: allow user-space setting of interface address

The interface address of the wireless device is determined by
the permanent address stored in the device. This patch allows
it to be overridden from user-space.

Reported-by: Maximilian Engelhardt <maxi@daemonizer.de>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: use perimeter lock in add_interface() callback

All callbacks that access driver functions should do that under
perimeter lock protection. The add_interface() callback was lacking
this lock.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: increase timer reference count for new timers only

On hardware reintialization reference count of
already existing timers would be increased again.
This leads to problems on module unloading.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800: convert read_eeprom functions to return an int value

Both the rtt2x00usb_eeprom_read and the ioremap
functions are allowed to fail, however their
return values are not checked in the read_eeprom
functions in the rt2800{pci,usb} drivers.

The patch adds the missing checks, and converts
all read_eeprom functions to return an int value,
so the error values can be propagated up to the
'rt2800_validate_eeprom' function.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Remove AR9485 1.0 macro

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: initialize morepending in brcms_b_recv()

drivers/net/wireless/brcm80211/brcmsmac/main.c: In function ‘brcms_b_recv’:
drivers/net/wireless/brcm80211/brcmsmac/main.c:7636: warning: ‘morepending’ may be used uninitialized in this function

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: allow to enable PS

Power save support was removed from iwlegacy due to possible firmware
crashes problems it cause. I use to plan first inspect code to find
reason of problems, fix them and then allow to enable PS. But
realistically - code inspection will not happen, so let's do it, and
wait for eventual bug reports.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: add flush callback

Dump implementation of flush, which just wait until all TX queues
become empty.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix column header comments for some initval arrays

Some 3-column initval arrays have wrong comments. The
column of these arrays is indexed by the 'freqIndex'
variable in 'ar5008_hw_process_ini' which only depends
on the actual band.

The 'initvals' tool from 'qca-swiss-army-knife' prints
the correct comment lines for these arrays, since commit
'atheros-initvals: fix comments for non-fastclock 3-column tables'
however the comments were not refreshed in ath9k.

The patch contains no functional changes.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: refactor carl9170_update_beacon

This patch moves parts of carl9170_update_beacon
into separate subroutines, so the parts become
more manageable.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: remove custom NUM_TID and friends

The commit: "mac80211: introduce IEEE80211_NUM_TIDS and use it"
introduced a generic NUM_TID definitions for all everyone.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: disable hw crypto for p2p networks

While the driver supports HW offload in a single
P2P client configuration, it doesn't support HW
offload in the concurrent P2P GO+CLIENT
configuration.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: don't enable hw crypto offload, if the fw doesn't support it

Previously, op_start would set disable_offload always
to false, even if it was set to true by the fw parser.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: Only specify interface combinations if more than one interface is possible

Otherwise carl9170 triggers a warning in cfg80211, from net/wireless/core.c

/* Combinations with just one interface aren't real */
if (WARN_ON(c->max_interfaces < 2))

Note: The number of supported interfaces is set by
the carl9170 firmware. The default number of
supported interfaces for all current firmwares is 2.
Therefore this warning can only be observed with
custom firmwares.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: allow P2P_GO interface creation after P2P_CLIENT

Janusz Dziedzic reported that after a change in wpa_supplicant
["nl80211: Automatically use concurrent P2P if possible"],
carl9170 was no longer able to host a P2P network.

This patch tackles the problem by allowing GO interfaces to be
registered, long after the P2P_CLIENT interface is brought up.

Reported-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: import 1.9.7 firmware headers

Import new headers from my firmware branch:
<https://github.com/chunkeey/carl9170fw>

visit our wiki at:
<http://wireless.kernel.org/en/users/Drivers/carl9170.fw>

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: advertise support for TDLS

Based on a quick test [ath9k and carl9170],
TDLS seemed to be working fine. And while
we are at it, let's move the wiphy feature
flag set from carl9170_alloc into a single
place in carl9170_fw.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: use the devres API for allocations

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: use the devres API for allocations/mappings

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800: refactor RFCSR initialization

rt2800_init_rfcsr() is too big, split RF initialization into per chip
functions. Code will change, but we should setup the same values onto
RF registers and in the same order as before.

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-john' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next

mac80211_hwsim: fix beacon timing

A beacon period starts at TSF time 0. Spoof this by
rounding the starting beacon time to a multiple of the
beacon interval, and keep TBTT aligned on TSF adjustment.

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211_hwsim: hrtimer beacon

For testing various timing-sensitive protocols (power
save, MBCA, etc.), a beacon accuracy of jiffies is not
sufficient. A tasklet_hrtimer is used for the beacon since
it runs the callback in soft-IRQ context with hrtimer
resolution.

Also handle BSS_CHANGED_BEACON_ENABLED for hwsim.

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
[simplify timer container_of]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211_hwsim: fix tsf adjustment

Make hwsim TSF offset adjustments cumulative and relative
to the fake PHY TSF. Now adding 1000us, then adding -1000us
doesn't result in a tsf_offset of -1000. Also the beacon
timestamp can now correctly be expressed as (tsf +
data->tsf_offset), which will be done in a later patch.

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: fix mesh_hwmp kerneldoc

One of the function names was wrong and some parameters were
missing.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: always check that grab_nic_access succeeds

This allows to let sparse check that the NIC access is
always released.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: fix spelling and value in LED registers.

Fix typo in the macro name and the wrong value.

Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: move some PCIe calls to better places

Synchronizing the IRQ is pointless when we will
then enable the RF-Kill interrupt again, but is
needed before we free it and the data needed to
handle IRQs; move it to the free function.

Simiarly, cancelling the replenish work struct
can move to the function that frees the RX data
structures.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: request IRQ only once

There's no need to request the IRQ every time the
device is started, we can request it just once.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: don't treat a bool as an error code

iwl_trans_grab_nic_access returns a boolean. So ret should
explicitely set to an error code and not rely on the value
returned by iwl_trans_grab_nic_access.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: virtualize SRAM access

Different transports implement the access to the SRAM in
different ways. Virtualize it.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: virtualize iwl_{grab,release}_nic_access

Since different transports have different ways to wake the
up the NIC, we need to virtualize it.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: use __packed

Use __packed instead of __attribute__((packed)).

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: let the op_mode run a FW while in RFKILL

In some cases, the fw should run even if the NIC is in
RFKILL. Make the API more flexible to allow that.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: don't verify fw after download

No need to verify that the fw has been written correctly.
In case it hasn't, we won't get ALIVE notification.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: clean up code in AGG

If we take a pointer to the tid_data, then use it.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: make the BC table layout configurable

This is needed for newer NICs.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: disallow more station changes

The following changes are invalid and should be
disallowed when a station already exists:
 * supported rates changes, except for TDLS peers
 * listen interval changes
 * HT capability changes

Disallow them and also update a mac80211 comment
explaining how they would be racy.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: unset peer's HT 40 MHz support if not usable

When an interface is configured to a 20 MHz channel
and the device as well as the peer are 40 MHz capable
the HT capabilities of the peer are not restricted to
20 MHz, even though they're supposed to be restricted
to the currently possible capabilities.

Unset the 40 MHz HT capability bits in this case.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wireless: use __aligned

Use __aligned(...) instead of __attribute__((aligned(...)))
in mac80211 and cfg80211.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: support HT notify channel width action

Support the HT notify channel width action frame
to update the rate scaling about the bandwidth
the peer can receive in.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wireless: use __packed in ieee80211.h

Use __packed instead of __attribute__((packed)).

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: split TX aggregation stop action

When TX aggregation is stopped, there are a few
different cases:
 - connection with the peer was dropped
 - session stop was requested locally
 - session stop was requested by the peer
 - connection was dropped while a session is stopping

The behaviour in these cases should be different, if
the connection is dropped then the driver should drop
all frames, otherwise the frames may continue to be
transmitted, aggregated in the case of a locally
requested session stop or unaggregated in the case of
the peer requesting session stop.

Split these different cases so that the driver can
act accordingly; however, treat local and remote stop
the same way and ask the driver to not send frames as
aggregated packets any more.

In the case of connection drop, the stop callback the
driver is otherwise supposed to call is no longer
required.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: move ieee80211_remove_tid_tx function

To call it from ___ieee80211_stop_tx_ba_session,
move the function and dependencies up.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: split out aggregation TX removal

Create the function ieee80211_remove_tid_tx to call
it from ___ieee80211_stop_tx_ba_session later.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: split aggregation stop by reason

The initiator/tx doesn't really identify why an
aggregation session is stopped, give a reason
for stopping that more clearly identifies what's
going on. This will help tell the driver clearly
what is expected of it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

nl80211/mac80211: support full station state in AP mode

Today, stations are added already associated. That is
inefficient if, for example, the driver has no room
for stations any more because then the station will
go through the entire auth/assoc handshake, only to
be kicked out afterwards.

To address this a bit better, at least with drivers
using the new station state callback, allow hostapd
to add stations in unauthenticated mode, just after
receiving the AUTH frame, before even replying. Thus
if there's no more space at that point, it can send
a negative auth frame back. It still needs to handle
later state transition errors though, of course.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>