ath9k: Resync beacons properly

After a chip reset, the beacon timers have to re-programmed
correctly for a station in associated state. Use the PS flags
to ensure that this is done after a TSF sync happens, otherwise
the driver ends up using incorrect values for TBTT/DTIM in
powersave mode.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix powersave locking

The 'ps_flags' is used/accessed in a variety of contexts
and requires proper locking. Use 'sc_pm_lock' appropriately.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Handle fatal interrupts properly

When a fatal interrupt is received or it is detected that the baseband
has hung, the chip has to be reset immediately.  Otherwise, we end up
processing spurious interrupts. Ensure that we bail out properly in
the ISR when the reset work hasn't completed yet.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Use atomic operations

The 'sc_flags' variable is being used in a number of places
with no locking whatsoever. This patch converts the usage
of sc_flags to atomic ops.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Move LNA code to antenna.c

And use a helper function to setup antennae after a reset.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix work handling

* Currently, there is no synchronization between the reset
  work and the tx-poll work. Fix this and make sure that we
  bail out properly if a reset work is in progress.

* Cleanup the PLL WAR and enable it for AR9340 too and
  use a helper for restarting work/timers after a reset.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Group link monitoring logic

Add link.c and move all the link/connection monitoring
code to it.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: improve BT FTP/PAN performance

When BT FTP/PAN transmits while WLAN is idle, the one of 9462 chain
often picks up BT's tx signal and starts receiving. If the current
weight is set to be higher than BT tx, BT tx will be aborted and this
also degrades BT performance. Hence lower WLAN rx priority in this
case only when there are no WLAN traffic.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix power state for MCI

Program MCI related power registers only if MCI interrupts
are enabled. This could help to reduce power consumptions when
WLAN alone is enabled in BT coex chips.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath: do not update cycle counters with sleep mode

When the chip is waking up from sleep state, the cycle counters
might have incorrect readings. So it is better not to update those
readings with software counters.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: BT coex performance tuning for AR9462

Use smaller aggregation limit and increasing aggregation threshold
for osla that could improve wlan performance when there is HID profile.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix BT RF performance

When software rfkill is triggered, before put the chip in reset
state, give LNA and SPDT control to BT to make sure BT can have
good RF performance.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: configure ar9462 switching regulator

Enable WLAN and BT mode for switching regulator discontinuous
orverride for AR9462 chips.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: program BT to control SPDT

program BT to control SPDT everytime while loading switch table
from eeprom.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix IQ calibration chain index

The chain index to perform IQ calibration is counted to number of valid
tx chains and then used for indexing chain specific registers. If the
chainmask is set to 0x2 (i.e chain 1 only), still it accesses chain 0
registers for chain 1. So use real chain index instead sequential one.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: cleanup MCI indentation

Fix bad indentation & if nesting to lose about two levels
of unnecessary indentation.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: update ar9462 initval table to fix rx

The wrong ADC sample phase that happen between awake and
network/full sleep will lead to improper rx noisefloor
calibration.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Use separate operational flags for BTCOEX

Also, use atomic operations to check the flags.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Remove SC_OP_OFFCHANNEL

mac80211's IEEE80211_CONF_OFFCHANNEL can be used directly
to track offchannel state. Also pass the correct boolean
value to ath9k_hw_startpcureceive().

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix variable usage

Exposed by sparse:
ar9003_mci.c:1134:31: warning: Using plain integer as NULL pointer

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add MCI interrupt to debugfs statistics

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Cleanup power mode API

The 'setChip' variable is unused, remove it and
simplify the functions.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix MCI usage

MCI has to be handled only when BTCOEX is actually enabled.
Check for this condition before calling MCI related functions
from various reset/calibration call-sites.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix AR_RTC_KEEP_AWAKE usage

The default value that is being programmed to AR_RTC_KEEP_AWAKE
is 0x2, there is no need to program it manually in various
functions.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Setup MCI interrupts properly

MCI interrupts have to be enabled only when BTCOEX is
actually in use.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Handle ASPM properly

ASPM has to be disabled when BTCOEX is in use, do this properly
by calling the bus-specific ASPM init routine after the
BTCOEX scheme has been determined.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Prune ath9k_init_device

Instead of cluttering ath9k_init_device() with 'ath_softc'
specific initialization code, use ath9k_init_softc() to
setup driver-specific work routines, timers etc.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add stations after AP start on reconfig

When performing a HW restart for an AP mode interface, add stations back
only after the AP is beaconing. This mimics the normal flow of STA
addition on AP.

Some devices (wlcore) do not support adding stations before beaconing,
so this has the added benefit of making recovery work for them.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: brcmsmac: fixed checkpatch and sparse warnings

Fixed checkpatch and sparse warnings related to aiutils.*

Signed-off-by: Chris Yungmann <yungmann.chris@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: validate remain-on-channel time better

The remain-on-channel time validation shouldn't
depend on the value of HZ, as it does now with
the check against jiffies, since then you might
use a value that works on one system but not on
another. Fix it by checking against a minimum
that's fixed.

Also add validation of the wait duration for a
management frame TX since this also translates
into remain-on-channel internally.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: recognize ARM Cortex M3

I found this core on a BCM4322, a PCI card in the Linksys WRT610N V1.
This core is not used by the driver, this patch just makes ssb show the
correct name.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Clear wowlan flag when drv_suspend returns failure

drv_resume can get called without a prior call to drv_suspend.
Consider the following steps:

1. Suspend is started but driver's drv_suspend returns error.
2. Suspend is aborted. local->wowlan flag is left set.
3. Interface is removed.
4. Suspend again. This time open_count is 0 so drv_suspend is
   not called and local->wowlan not cleared.
5. On resume ieee80211_reconfig will call drv_resume since
   local->wowlan is set.

Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Add missing mesh parameter dot11MeshForwarding for debugfs

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: print info when disabling HT

Make mac80211 print a message when it disables
HT due to the connection using WEP/TKIP or due
to the AP not supporting WMM/QoS.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: configure 11b/g channel access rules for legacy APs

For each EDCA TX queue change default settings (in STA mode) to conform
old 802.11b/g channel access rules. This is needed for drivers that do
not have QoS enable/disable "switch" (like rt2x00) to make them work
properly with legacy APs.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Ensure a fair beacon distribution in IBSS mode

Configure CWmin based on slot time for IBSS mode. This helps
in increasing the beacon distribution of ath9k to accepted
levels in 11a mode.

Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00:Add RT5392 chipset support

Signed-off-by: Zero.Lin <Zero.Lin@mediatek.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl4965: claim RSN IBSS support

Similar like other drivers including iwl3945, do not configure group
keys to the hardware (on Ad-Hoc mode) to make IBSS RSN work.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: claim RSN IBSS support

Similar like other drivers, do not configure group keys to the hardware
(on Ad-Hoc mode) to make IBSS RSN work.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix/add bits for spectral scanning

Updates for spectral scanning register modification for AR93x:
 * fix bits for spectral_scan_count
 * add bits for new parameters

Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rfkill: Add the capability to switch all devices of all type in __rfkill_switch_all().

__rfkill_switch_all() switches the state of devices of a given type; however,
it does not switch devices of all type (RFKILL_TYPE_ALL). As a result, it
ignores the keycode "KEY_RFKILL" from another module, i.e. eeepc-wmi.

This fix is to make __rfkill_switch_all() to be able to switch not only
devices of a given type but also all devices.

Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: clarify set_channel APIs

Now that we've removed all uses of the set_channel
API except for the monitor channel and in libertas,
clarify this. Split the libertas mesh use into a
new libertas_set_mesh_channel() operation, just to
keep backward compatibility, and rename the normal
set_channel() to set_monitor_channel().

Also describe the desired set_monitor_channel()
semantics more clearly.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless

Conflicts:
drivers/net/wireless/iwlwifi/iwl-drv.c

Merge branch 'master' of git://git./linux/kernel/git/bluetooth/bluetooth

net/wireless: ipw2200: introduce ipw_read_eeprom function

We separate reading of device's eeprom content from writing it back
to the device's sram.

Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: support NL80211_HIDDEN_SSID_ZERO_LEN for uAP

mwifiex uAP supports NL80211_HIDDEN_SSID_ZERO_LEN type of hidden
SSID only. NL80211_HIDDEN_SSID_ZERO_CONTENTS is not supported.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: invalidate bss config before setting channel for uAP

Mark bss_config parameters as invalid before setting AP channel.
This prevents from setting invalid parameters while setting AP
channel to FW.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: provide channel to join_mesh function

Just like the AP mode patch, instead of setting
the channel and then joining the mesh network,
provide the channel to join the network on to
the join_mesh() function.

Like in AP mode, you can also give the channel
to the join-mesh nl80211 command now.

Unlike AP mode, it picks a default channel if
none was given.

As libertas uses mesh mode interfaces but has
no join_mesh callback and we can't simply break
it, keep some compatibility code for that case
and configure the channel directly for it.

In the non-libertas case, where we store the
channel until join, allow setting it while the
interface is down.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: disallow setting channel on WDS interfaces

If it worked (Felix says it doesn't right now), the
typical use-case for WDS interfaces would be to be
slaved to AP mode interfaces. Therefore, it isn't
necessary to set the channel on WDS interfaces. As
they don't support powersave or anything like that,
they also couldn't use a different channel anyway.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: provide channel to start_ap function

Instead of setting the channel first and then
starting the AP, let cfg80211 store the channel
and provide it as one of the AP settings.

This means that now you have to set the channel
before you can start an AP interface, but since
hostapd/wpa_supplicant always do that we're OK
with this change.

Alternatively, it's now possible to give the
channel as an attribute to the start-ap nl80211
command, overriding any preset channel.

Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: simplify cfg80211_can_beacon_sec_chan API

Change cfg80211_can_beacon_sec_chan() to return true
if there is no secondary channel to simplify all the
current users of it. They all check the channel type
before calling the function because it returns false
if there's no secondary channel.

Also actually document the return value.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: move ieee80211_set_channel function

Move the set_channel function up so it can be used
by other code in this file in the future.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: clean up ieee80211_set_channel

There's no need for ieee80211_set_channel to check
whether a change in configuration happened since
ieee80211_hw_config() auto-detects it.

Additionally, it's wrong to pretend the HT config
for the BSS changed, it didn't, the BSS can't be
up & running (AP beaconing etc.) when the channel
type is changed anyway.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: simplify association HT parameters

Instead of passing around the entire HT information
IE, extract only the HT parameters field and disable
HT if the HT information IE isn't present and well-
formed.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: deprecate CFG80211_WEXT

Almost all wireless tools have transitioned to
or at least added compatibility with nl80211 so
there's no real need for CONFIG_CFG80211_WEXT
any more. Mark it for removal, and also change
the default to not be enabled.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: remove wext sysfs

The only user of this was hal prior to its 0.5.12
release which happened over two years ago, so I'm
sure this can be removed without issues.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: add debugging to shadow registers and fix typo

Add a debugging log when using shadow
registers. Also fix a minor typo in this
connection.

Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: clean up coding style in PCIe transport

Mostly clean up indentation around parentheses
after if, function calls, etc. and also a few
unneeded line breaks and some other things.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: move notification wait into core

This code is a library to be used by multiple
opmodes, so move it into the iwlwifi module.

Reviewed-by: Donald H Fry <donald.h.fry@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: implement dynamic opmode loading

This is the next step in splitting up the driver,
making the uCode API dependent pieces of it live
in separate modules. Right now there's only one
so it's not user-selectable, but we're actively
working on more.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: move IWL_CMD_FAILED_MSK

This is common, not uCode API specific, so move
it to the transport together with the command
header struct definition.

Reviewed-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Guy Cohen <guy.cohen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: properly handle device_set_wakeup_enable

This is intended to be set whenever wakeup will be
needed upon suspend, not only when suspending, so
use the new callbacks to set it then.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: Move IWL_MASK macro to transport.

This macro is needed by other transports besides PCIe, thus
moving to a common location.

Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: s/iwlagn_unmap_tfd/iwl_unmap_tfd

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: s/iwlagn_txq_free_tfd/iwl_txq_free_tfd

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: add __printf argument checking

Joe Perches suggested adding the __printf attribute
to the __iwl_dbg function to check arguments; add it
to all of the logging functions (err, warn, info, dbg
and crit.)

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix debug print in iwl_sta_calc_ht_flags

We missed passing an argument to the
debug print. Fix it.

Cc: stable@kernel.org
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix prints in iwl_rx_handle

The debug prints were wrong and buggy. The HW pointer wasn't printed
correctly, it was mixed up with the pointer to the rxbuf.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Add support for RT5360 based PCI devices.

This chip is used at least by the D-Link DWA-525 adapter.

Signed-off-by: Alex Villac<ED>s Lasso <a_villacis@palosanto.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: remove ieee80211_get_operstate()

ieee80211_get_operstate() was used by drivers in order to
know whether the sta link is up, but it's no longer needed
(nor used) as mac80211 notifies the drivers about
authorization changes (via the sta_state callback)

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Support ethtool getstats api.

This returns many of the values that formerly could
only be obtained from debugfs.  This should be an
improvement when trying to access these counters
programatically.  Currently this support is only
enabled when DEBUGFS is enabled because otherwise
these stats are not accumulated.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net: mac80211: Add and use ibss_vdbg debugging macro

Simplify the use of #ifdef CONFIG_MAC80211_IBSS_DEBUG/#endif
by adding a logging macro to encapsulate the test.

Convert the appropriate uses too.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net: mac80211: Add and use ht_vdbg debugging macro

Simplify the use of #ifdef CONFIG_MAC80211_HT_DEBUG/#endif
by adding a logging macro to encapsulate the test.

Convert the appropriate uses too.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net: mac80211: Convert printk(KERN_DEBUG to pr_debug

Standardize the debugging to be able to use dynamic_debug.

Coalesce formats, align arguments.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: send beacon loss events to userspace

Send beacon loss events to userspace, so it will be
able to initiate roaming before disconnection

Signed-off-by: Holger Schurig <holgerschurig@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211: add new rssi event to indicate beacon loss

Tell userspace about beacon loss event.
This event doesn't replace the deauth/disassoc that
might come if the AP is not available.

The driver can send this event in order to hint
userspace what might follow (which in turn can
use it as roaming trigger).

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix modal EEPROM dump

we provide excess buffer size for 'simple_read_from_buffer'
for modal EEPROM dump. This results in trailing NULL bytes
at the end of EEPROM dump, fix this.

Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Reported-by: Holger Schurig <holgerschurig@googlemail.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Tested-by: Holger Schurig <holgerschurig@gogglemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: brcmu_pkt_buf_free_skb() should handle NULL

This is potentially called with NULL pointers, for example, look at
brcmf_c_prec_enq().  Since it's a free() function, probably people
expect it to handle NULL pointers.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: remove an unneeded NULL check

This code causes a static checker warning because "pi" gets dereferenced
before it is checked.  The dereference is inside the write_phy_reg()
function which is called from wlc_phy_write_txmacreg_nphy().

This code is only called from wlc_phy_init_nphy() and "pi" is a
valid pointer so we can remove the check for NULL.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800usb: 2001:3c17 is an RT3370 device

D-Link DWA-123 rev A1

Signed-off-by: Albert Pool<albertpool@solcon.nl>
Cc: <stable@vger.kernel.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: allow channel change while mesh is down

Allow channel change on a mesh interface if the interface is up and no
mesh is started.

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fail authentication when AP denied authentication

ieee80211_rx_mgmt_auth() doesn't handle denied authentication
properly - it authenticates the station and waits for association
(for 5 seconds) instead of failing the authentication.

Fix it by destroying auth_data and bailing out instead.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@vger.kernel.org #3.4
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: use offchannel queue only when supported

Commit 3a25a8c ("mac80211: add improved HW queue control")
added support for offchannel queue mapping. However, this
mapping is only valid when the driver supports
IEEE80211_HW_QUEUE_CONTROL.

Check whether the driver supports IEEE80211_HW_QUEUE_CONTROL
before setting the hw_queue to the mapped offchannel queue.

(This patch doesn't have any actual effect, because
hw_queue is overridden in ieee80211_tx() anyway,
so this is merely some cleanup)

Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: allow low-level drivers to set netdev feature bits

Low level drivers can now set certain netdev feature bits in
netdev_features member of the ieee80211_hw struct. These will be
propagated to every netdev created from this HW.

The white-listed features currently include only ones related to HW
checksumming.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: fix interface combinations check

If a given interface combination doesn't contain
a required interface type then we missed checking
that and erroneously allowed it even though iface
type wasn't there at all. Add a check that makes
sure that all interface types are accounted for.

Cc: stable@kernel.org
Reported-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: unregister LEDs if mac80211 registration fails

Otherwise the LEDs stick around and cause issues the
next time around since they're still there but not
really hooked up.

Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix double free/complete in firmware loading

Linus reported that due to mac80211 failing to register
the device (due to WoWLAN) his machine crashed etc. as
we double-freed the vmalloc() firmware area. His patch
to fix it was very similar to this one but I noticed
that there's another bug in the area: we complete the
completion before starting, so since we're running in
a work struct context stop() could be called while in
the middle of start() which will almost certainly lead
to issues.

Make a modification similar to his to avoid the double-
free but also move the completion to another spot so it
is only done after start() either finished or failed so
that stop() can have a consistent state.

Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Bluetooth: Fix checking the wrong flag when accepting a socket

Most probably a typo, the check should have been for BT_SK_DEFER_SETUP
instead of BT_DEFER_SETUP (which right now only represents a socket
option).

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

iwlwifi: disable WoWLAN if !CONFIG_PM_SLEEP

If CONFIG_PM_SLEEP is disabled, then iwlwifi doesn't
support suspend/resume handlers and thus mac80211
(correctly) refuses advertising WoWLAN. Disable
WoWLAN in the driver in this case.

Cc: stable@kernel.org
Reported-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix non RCU-safe sta_list manipulation

sta_info_cleanup locks the sta_list using rcu_read_lock however
the delete operation isn't rcu safe. A race between sta_info_cleanup
timer being called and a STA being removed can occur which leads
to a panic while traversing sta_list. Fix this by switching to the
RCU-safe versions.

Cc: stable@vger.kernel.org
Reported-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: add ext PA workaround for BCM4331 and BCM43431

MacBook Pro models with BCM4331 wireless have been found to have the ext
PA lines disabled after resuming from S3 without external power attach.
This causes them to be unable to transmit. Add a workaround to ensure
that the ext PA lines are enabled on BCM4331. Also extend all handling
of ext PA line muxing to BCM43431 as is done in the Broadcom SDK.

BugLink: http://bugs.launchpad.net/bugs/925577
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: stable@vger.kernel.org
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: use atomic variable for seqno

Remove spinlock as atomic_t can be used instead. Note we use only 16
lower bits, upper bits are changed but we impilcilty cast to u16.

This fix possible deadlock on IBSS mode reproted by lockdep:

=================================
[ INFO: inconsistent lock state ]
3.4.0-wl+ #4 Not tainted
---------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
kworker/u:2/30374 [HC0[0]:SC0[0]:HE1:SE1] takes:
 (&(&intf->seqlock)->rlock){+.?...}, at: [<f9979a20>] rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
{IN-SOFTIRQ-W} state was registered at:
  [<c04978ab>] __lock_acquire+0x47b/0x1050
  [<c0498504>] lock_acquire+0x84/0xf0
  [<c0835733>] _raw_spin_lock+0x33/0x40
  [<f9979a20>] rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
  [<f9979f2a>] rt2x00queue_write_tx_frame+0x1a/0x300 [rt2x00lib]
  [<f997834f>] rt2x00mac_tx+0x7f/0x380 [rt2x00lib]
  [<f98fe363>] __ieee80211_tx+0x1b3/0x300 [mac80211]
  [<f98ffdf5>] ieee80211_tx+0x105/0x130 [mac80211]
  [<f99000dd>] ieee80211_xmit+0xad/0x100 [mac80211]
  [<f9900519>] ieee80211_subif_start_xmit+0x2d9/0x930 [mac80211]
  [<c0782e87>] dev_hard_start_xmit+0x307/0x660
  [<c079bb71>] sch_direct_xmit+0xa1/0x1e0
  [<c0784bb3>] dev_queue_xmit+0x183/0x730
  [<c078c27a>] neigh_resolve_output+0xfa/0x1e0
  [<c07b436a>] ip_finish_output+0x24a/0x460
  [<c07b4897>] ip_output+0xb7/0x100
  [<c07b2d60>] ip_local_out+0x20/0x60
  [<c07e01ff>] igmpv3_sendpack+0x4f/0x60
  [<c07e108f>] igmp_ifc_timer_expire+0x29f/0x330
  [<c04520fc>] run_timer_softirq+0x15c/0x2f0
  [<c0449e3e>] __do_softirq+0xae/0x1e0
irq event stamp: 18380437
hardirqs last  enabled at (18380437): [<c0526027>] __slab_alloc.clone.3+0x67/0x5f0
hardirqs last disabled at (18380436): [<c0525ff3>] __slab_alloc.clone.3+0x33/0x5f0
softirqs last  enabled at (18377616): [<c0449eb3>] __do_softirq+0x123/0x1e0
softirqs last disabled at (18377611): [<c041278d>] do_softirq+0x9d/0xe0

other info that might help us debug this:
 Possible unsafe locking scenario:

       CPU0
       ----
  lock(&(&intf->seqlock)->rlock);
  <Interrupt>
    lock(&(&intf->seqlock)->rlock);

 *** DEADLOCK ***

4 locks held by kworker/u:2/30374:
 #0:  (wiphy_name(local->hw.wiphy)){++++.+}, at: [<c045cf99>] process_one_work+0x109/0x3f0
 #1:  ((&sdata->work)){+.+.+.}, at: [<c045cf99>] process_one_work+0x109/0x3f0
 #2:  (&ifibss->mtx){+.+.+.}, at: [<f98f005b>] ieee80211_ibss_work+0x1b/0x470 [mac80211]
 #3:  (&intf->beacon_skb_mutex){+.+...}, at: [<f997a644>] rt2x00queue_update_beacon+0x24/0x50 [rt2x00lib]

stack backtrace:
Pid: 30374, comm: kworker/u:2 Not tainted 3.4.0-wl+ #4
Call Trace:
 [<c04962a6>] print_usage_bug+0x1f6/0x220
 [<c0496a12>] mark_lock+0x2c2/0x300
 [<c0495ff0>] ? check_usage_forwards+0xc0/0xc0
 [<c04978ec>] __lock_acquire+0x4bc/0x1050
 [<c0527890>] ? __kmalloc_track_caller+0x1c0/0x1d0
 [<c0777fb6>] ? copy_skb_header+0x26/0x90
 [<c0498504>] lock_acquire+0x84/0xf0
 [<f9979a20>] ? rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
 [<c0835733>] _raw_spin_lock+0x33/0x40
 [<f9979a20>] ? rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
 [<f9979a20>] rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
 [<f997a5cf>] rt2x00queue_update_beacon_locked+0x5f/0xb0 [rt2x00lib]
 [<f997a64d>] rt2x00queue_update_beacon+0x2d/0x50 [rt2x00lib]
 [<f9977e3a>] rt2x00mac_bss_info_changed+0x1ca/0x200 [rt2x00lib]
 [<f9977c70>] ? rt2x00mac_remove_interface+0x70/0x70 [rt2x00lib]
 [<f98e4dd0>] ieee80211_bss_info_change_notify+0xe0/0x1d0 [mac80211]
 [<f98ef7b8>] __ieee80211_sta_join_ibss+0x3b8/0x610 [mac80211]
 [<c0496ab4>] ? mark_held_locks+0x64/0xc0
 [<c0440012>] ? virt_efi_query_capsule_caps+0x12/0x50
 [<f98efb09>] ieee80211_sta_join_ibss+0xf9/0x140 [mac80211]
 [<f98f0456>] ieee80211_ibss_work+0x416/0x470 [mac80211]
 [<c0496d8b>] ? trace_hardirqs_on+0xb/0x10
 [<c077683b>] ? skb_dequeue+0x4b/0x70
 [<f98f207f>] ieee80211_iface_work+0x13f/0x230 [mac80211]
 [<c045cf99>] ? process_one_work+0x109/0x3f0
 [<c045d015>] process_one_work+0x185/0x3f0
 [<c045cf99>] ? process_one_work+0x109/0x3f0
 [<f98f1f40>] ? ieee80211_teardown_sdata+0xa0/0xa0 [mac80211]
 [<c045ed86>] worker_thread+0x116/0x270
 [<c045ec70>] ? manage_workers+0x1e0/0x1e0
 [<c0462f64>] kthread+0x84/0x90
 [<c0462ee0>] ? __init_kthread_worker+0x60/0x60
 [<c083d382>] kernel_thread_helper+0x6/0x10

Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: Fix likely misuse of | for &

Using | with a constant is always true.
Likely this should have be &.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Fix likely misuse of | for &

Using | with a constant is always true.
Likely this should have be &.

cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add missing rcu_read_lock/unlock in agg-rx session timer

Fixes a lockdep warning:

===================================================
[ INFO: suspicious rcu_dereference_check() usage. ]
---------------------------------------------------
net/mac80211/agg-rx.c:148 invoked rcu_dereference_check() without protection!

other info that might help us debug this:

rcu_scheduler_active = 1, debug_locks = 1
1 lock held by arecord/11226:
 #0:  (&tid_agg_rx->session_timer){+.-...}, at: [<ffffffff81066bb0>] call_timer_fn+0x0/0x360

stack backtrace:
Pid: 11226, comm: arecord Not tainted 3.1.0-kml #16
Call Trace:
 <IRQ>  [<ffffffff81093454>] lockdep_rcu_dereference+0xa4/0xc0
 [<ffffffffa02778c9>] sta_rx_agg_session_timer_expired+0xc9/0x110 [mac80211]
 [<ffffffffa0277800>] ? ieee80211_process_addba_resp+0x220/0x220 [mac80211]
 [<ffffffff81066c3a>] call_timer_fn+0x8a/0x360
 [<ffffffff81066bb0>] ? init_timer_deferrable_key+0x30/0x30
 [<ffffffff81477bb0>] ? _raw_spin_unlock_irq+0x30/0x70
 [<ffffffff81067049>] run_timer_softirq+0x139/0x310
 [<ffffffff81091d5e>] ? put_lock_stats.isra.25+0xe/0x40
 [<ffffffff810922ac>] ? lock_release_holdtime.part.26+0xdc/0x160
 [<ffffffffa0277800>] ? ieee80211_process_addba_resp+0x220/0x220 [mac80211]
 [<ffffffff8105cb78>] __do_softirq+0xc8/0x3c0
 [<ffffffff8108f088>] ? tick_dev_program_event+0x48/0x110
 [<ffffffff8108f16f>] ? tick_program_event+0x1f/0x30
 [<ffffffff81153b15>] ? putname+0x35/0x50
 [<ffffffff8147a43c>] call_softirq+0x1c/0x30
 [<ffffffff81004c55>] do_softirq+0xa5/0xe0
 [<ffffffff8105d1ee>] irq_exit+0xae/0xe0
 [<ffffffff8147ac6b>] smp_apic_timer_interrupt+0x6b/0x98
 [<ffffffff81479ab3>] apic_timer_interrupt+0x73/0x80
 <EOI>  [<ffffffff8146aac6>] ? free_debug_processing+0x1a1/0x1d5
 [<ffffffff81153b15>] ? putname+0x35/0x50
 [<ffffffff8146ab2b>] __slab_free+0x31/0x2ca
 [<ffffffff81477c3a>] ? _raw_spin_unlock_irqrestore+0x4a/0x90
 [<ffffffff81253b8f>] ? __debug_check_no_obj_freed+0x15f/0x210
 [<ffffffff81097054>] ? lock_release_nested+0x84/0xc0
 [<ffffffff8113ec55>] ? kmem_cache_free+0x105/0x250
 [<ffffffff81153b15>] ? putname+0x35/0x50
 [<ffffffff81153b15>] ? putname+0x35/0x50
 [<ffffffff8113ed8f>] kmem_cache_free+0x23f/0x250
 [<ffffffff81153b15>] putname+0x35/0x50
 [<ffffffff81146d8d>] do_sys_open+0x16d/0x1d0
 [<ffffffff81146e10>] sys_open+0x20/0x30
 [<ffffffff81478f42>] system_call_fastpath+0x16/0x1b

Reported-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: clean up remain-on-channel on interface stop

When any interface goes down, it could be the one that we
were doing a remain-on-channel with. We therefore need to
cancel the remain-on-channel and flush the related work
structs so they don't run after the interface has been
removed or even destroyed.

It's also possible in this case that an off-channel SKB
was never transmitted, so free it if this is the case.
Note that this can also happen if the driver finishes
the off-channel period without ever starting it.

Cc: stable@kernel.org
Reported-by: Nirav Shah <nirav.j2.shah@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211_hwsim: advertise interface combinations

Enforcing interface combinations broke uses of hwsim
with multiple virtual interfaces. Advertise that all
combinations are possible to fix this.

Reported-by: Nirav Shah <nirav.j2.shah@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix error in station state transitions during reconfig

As part of hardware reconfig mac80211 tries
to restore the station state to its values
before the hardware reconfig, but it only
goes to the last-state - 1. Fix this
off-by-one error.

Cc: stable@kernel.org [3.4]
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix TX power antenna access

Since my commit
  iwlwifi: use valid TX/RX antenna from hw_params
the config values are pure overrides, not the
real values for all hardware. Therefore, the
EEPROM TX power reading code checks the wrong
values, it should check the hw_params values.

Cc: stable@kernel.org [3.4]
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Fix Unreachable Mesh Station Problem when joining to another MBSS

Mesh station that joins an MBSS is reachable using mesh portal with 6
address frame by mesh stations from another MBSS if these two different
MBSSes are bridged. However, if the mesh station later moves into the
same MBSS of those mesh stations, it is unreachable by mesh stations
in the MBSS due to the mpp_paths table is not deleted. A quick fix
is to perform mesh_path_lookup, if it is available for the target
destination, mpp_path_lookup is not performed. When the mesh station
moves back to its original MBSS, the mesh_paths will be deleted once
expired. So, it will be reachable using mpp_path_lookup again.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>