drm/nouveau/bsp/g92: disable by default

commit 194d68dd051c2dd5ac2b522ae16100e774e8d869 upstream.

G92's seem to require some additional bit of initialization before the
BSP engine can work. It feels like clocks are not set up for the
underlying VLD engine, which means that all commands submitted to the
xtensa chip end up hanging. VP seems to work fine though.

This still allows people to force-enable the bsp engine if they want to
play around with it, but makes it harder for the card to hang by
default.

Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: esd_usb2: Fix can_dlc value for received RTR, frames

commit 72d92e865d1560723e1957ee3f393688c49ca5bf upstream.

The dlc member of the struct rx_msg contains also the ESD_RTR flag to
mark received RTR frames. Without the fix the can_dlc value for received
RTR frames would always be set to 8 by get_can_dlc() instead of the
received value.

Fixes: 96d8e90382dc ("can: Add driver for esd CAN-USB/2 device")
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: musb: Check for host-mode using is_host_active() on reset interrupt

commit 445ef61543da3db5b699f87fb0aa4f227165f6ed upstream.

The sunxi musb has a bug where sometimes it will generate a babble
error on device disconnect instead of a disconnect IRQ. When this
happens the musb controller switches from host mode to device mode
(it clears MUSB_DEVCTL_HM/MUSB_DEVCTL_SESSION and sets
MUSB_DEVCTL_BDEVICE) and gets stuck in this state.

The babble error is misdetected as a bus reset because MUSB_DEVCTL_HM
was cleared.

To fix this, use is_host_active() rather than (devctl & MUSB_DEVCTL_HM)
to detect babble error so that sunxi musb babble recovery can handle it
by restoring the mode. This information is provided by the driver logic
and does not rely on register contents.

Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: musb: sunxi: Explicitly release USB PHY on exit

commit 6ed05c68cbcae42cd52b8e53b66952bfa9c002ce upstream.

This fixes a kernel oops when unloading the driver due to usb_put_phy
being called after usb_phy_generic_unregister when the device is
detached. Calling usb_phy_generic_unregister causes x->dev->driver to
be NULL in usb_put_phy and results in a NULL pointer dereference.

Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: gs_usb: fix busy loop if no more TX context is available

commit 97819f943063b622eca44d3644067c190dc75039 upstream.

If sending messages with no cable connected, it quickly happens that
there is no more TX context available. Then "gs_can_start_xmit()"
returns with "NETDEV_TX_BUSY" and the upper layer does retry
immediately keeping the CPU busy. To fix that issue, I moved
"atomic_dec(&dev->active_tx_urbs)" from "gs_usb_xmit_callback()" to
the TX done handling in "gs_usb_receive_bulk_callback()". Renaming
"active_tx_urbs" to "active_tx_contexts" and moving it into
"gs_[alloc|free]_tx_context()" would also make sense.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: usb-audio: Add native DSD support for Pro-Ject Pre Box S2 Digital

commit 9bb201a5d5acc733943e8af7151cceab9d976a69 upstream.

Add native DSD support quirk for Pro-Ject Pre Box S2 Digital USB id
2772:0230.

Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: hub: Allow reset retry for USB2 devices on connect bounce

commit 1ac7db63333db1eeff901bfd6bbcd502b4634fa4 upstream.

If the connect status change is set during reset signaling, but
the status remains connected just retry port reset.

This solves an issue with connecting a 90W HP Thunderbolt 3 dock
with a Lenovo Carbon x1 (5th generation) which causes a 30min loop
of a high speed device being re-discovererd before usb ports starts
working.

[...]
[ 389.023845] usb 3-1: new high-speed USB device number 55 using xhci_hcd
[ 389.491841] usb 3-1: new high-speed USB device number 56 using xhci_hcd
[ 389.959928] usb 3-1: new high-speed USB device number 57 using xhci_hcd
[...]

This is caused by a high speed device that doesn't successfully go to the
enabled state after the second port reset. Instead the connection bounces
(connected, with connect status change), bailing out completely from
enumeration just to restart from scratch.

Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1716332
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: quirks: add quirk for WORLDE MINI MIDI keyboard

commit 2811501e6d8f5747d08f8e25b9ecf472d0dc4c7d upstream.

This keyboard doesn't implement Get String descriptors properly even
though string indexes are valid. What happens is that when requesting
for the String descriptor, the device disconnects and
reconnects. Without this quirk, this loop will continue forever.

Cc: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Владимир Мартьянов <vilgeforce@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: cdc_acm: Add quirk for Elatec TWN3

commit 765fb2f181cad669f2beb87842a05d8071f2be85 upstream.

Elatec TWN3 has the union descriptor on data interface. This results in
failure to bind the device to the driver with the following log:
  usb 1-1.2: new full speed USB device using streamplug-ehci and address 4
  usb 1-1.2: New USB device found, idVendor=09d8, idProduct=0320
  usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
  usb 1-1.2: Product: RFID Device (COM)
  usb 1-1.2: Manufacturer: OEM
  cdc_acm 1-1.2:1.0: Zero length descriptor references
  cdc_acm: probe of 1-1.2:1.0 failed with error -22

Adding the NO_UNION_NORMAL quirk for the device fixes the issue.

`lsusb -v` of the device:

Bus 001 Device 003: ID 09d8:0320
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            2 Communications
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        32
  idVendor           0x09d8
  idProduct          0x0320
  bcdDevice            3.00
  iManufacturer           1 OEM
  iProduct                2 RFID Device (COM)
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           67
    bNumInterfaces          2
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0x80
      (Bus Powered)
    MaxPower              250mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         2 Communications
      bInterfaceSubClass      2 Abstract (modem)
      bInterfaceProtocol      1 AT-commands (v.25ter)
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x83  EP 3 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0020  1x 32 bytes
        bInterval               2
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        1
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass        10 CDC Data
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0020  1x 32 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0020  1x 32 bytes
        bInterval               0
      CDC Header:
        bcdCDC               1.10
      CDC Call Management:
        bmCapabilities       0x03
          call management
          use DataInterface
        bDataInterface          1
      CDC ACM:
        bmCapabilities       0x06
          sends break
          line coding and serial state
      CDC Union:
        bMasterInterface        0
        bSlaveInterface         1
Device Status:     0x0000
  (Bus Powered)

Signed-off-by: Maksim Salau <msalau@iotecha.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: metro-usb: add MS7820 device id

commit 31dc3f819bac28a0990b36510197560258ab7421 upstream.

Add device-id entry for (Honeywell) Metrologic MS7820 bar code scanner.

The device has two interfaces (in this mode?); a vendor-specific
interface with two interrupt endpoints and a second HID interface, which
we do not bind to.

Reported-by: Ladislav Dobrovsky <ladislav.dobrovsky@gmail.com>
Tested-by: Ladislav Dobrovsky <ladislav.dobrovsky@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: core: fix out-of-bounds access bug in usb_get_bos_descriptor()

commit 1c0edc3633b56000e18d82fc241e3995ca18a69e upstream.

Andrey used the syzkaller fuzzer to find an out-of-bounds memory
access in usb_get_bos_descriptor().  The code wasn't checking that the
next usb_dev_cap_header structure could fit into the remaining buffer
space.

This patch fixes the error and also reduces the bNumDeviceCaps field
in the header to match the actual number of capabilities found, in
cases where there are fewer than expected.

Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: devio: Revert "USB: devio: Don't corrupt user memory"

commit 845d584f41eac3475c21e4a7d5e88d0f6e410cf7 upstream.

Taking the uurb->buffer_length userspace passes in as a maximum for the
actual urbs transfer_buffer_length causes 2 serious issues:

1) It breaks isochronous support for all userspace apps using libusb,
   as existing libusb versions pass in 0 for uurb->buffer_length,
   relying on the kernel using the lenghts of the usbdevfs_iso_packet_desc
   descriptors passed in added together as buffer length.

   This for example causes redirection of USB audio and Webcam's into
   virtual machines using qemu-kvm to no longer work. This is a userspace
   ABI break and as such must be reverted.

   Note that the original commit does not protect other users / the
   kernels memory, it only stops the userspace process making the call
   from shooting itself in the foot.

2) It may cause the kernel to program host controllers to DMA over random
   memory. Just as the devio code used to only look at the iso_packet_desc
   lenghts, the host drivers do the same, relying on the submitter of the
   urbs to make sure the entire buffer is large enough and not checking
   transfer_buffer_length.

   But the "USB: devio: Don't corrupt user memory" commit now takes the
   userspace provided uurb->buffer_length for the buffer-size while copying
   over the user-provided iso_packet_desc lengths 1:1, allowing the user
   to specify a small buffer size while programming the host controller to
   dma a lot more data.

   (Atleast the ohci, uhci, xhci and fhci drivers do not check
    transfer_buffer_length for isoc transfers.)

This reverts commit fa1ed74eb1c2 ("USB: devio: Don't corrupt user memory")
fixing both these issues.

Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.4.94

Revert "tty: goldfish: Fix a parameter of a call to free_irq"

This reverts commit 01b3db29ba1edd79b9c3e7cd294739b70257d278 which is
commit 1a5c2d1de7d35f5eb9793266237903348989502b upstream.

Ben writes:
This fixes a bug introduced in 4.6 by commit 465893e18878 "tty:
goldfish: support platform_device with id -1".  For earlier
kernel versions, it *introduces* a bug.

So let's drop it.

Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org

cpufreq: CPPC: add ACPI_PROCESSOR dependency

[ Upstream commit a578884fa0d2768f13d37c6591a9e1ed600482d3 ]

Without the Kconfig dependency, we can get this warning:

warning: ACPI_CPPC_CPUFREQ selects ACPI_CPPC_LIB which has unmet direct dependencies (ACPI && ACPI_PROCESSOR)

Fixes: 5477fb3bd1e8 (ACPI / CPPC: Add a CPUFreq driver for use with CPPC)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nfsd/callback: Cleanup callback cred on shutdown

[ Upstream commit f7d1ddbe7648af7460d23688c8c131342eb43b3a ]

The rpccred gotten from rpc_lookup_machine_cred() should be put when
state is shutdown.

Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

target/iscsi: Fix unsolicited data seq_end_offset calculation

[ Upstream commit 4d65491c269729a1e3b375c45e73213f49103d33 ]

In case of unsolicited data for the first sequence
seq_end_offset must be set to minimum of total data length
and FirstBurstLength, so do not add cmd->write_data_done
to the min of total data length and FirstBurstLength.

This patch avoids that with ImmediateData=Yes, InitialR2T=No,
MaxXmitDataSegmentLength < FirstBurstLength that a WRITE command
with IO size above FirstBurstLength triggers sequence error
messages, for example

Set following parameters on target (linux-4.8.12)
ImmediateData = Yes
InitialR2T = No
MaxXmitDataSegmentLength = 8k
FirstBurstLength = 64k

Log in from Open iSCSI initiator and execute
dd if=/dev/zero of=/dev/sdb bs=128k count=1 oflag=direct

Error messages on target
Command ITT: 0x00000035 with Offset: 65536, Length: 8192 outside
of Sequence 73728:131072 while DataSequenceInOrder=Yes.
Command ITT: 0x00000035, received DataSN: 0x00000001 higher than
expected 0x00000000.
Unable to perform within-command recovery while ERL=0.

Signed-off-by: Varun Prakash <varun@chelsio.com>
[ bvanassche: Use min() instead of open-coding it / edited patch description ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

uapi: fix linux/mroute6.h userspace compilation errors

[ Upstream commit 72aa107df6a275cf03359934ca5799a2be7a1bf7 ]

Include <linux/in6.h> to fix the following linux/mroute6.h userspace
compilation errors:

/usr/include/linux/mroute6.h:80:22: error: field 'mf6cc_origin' has incomplete type
  struct sockaddr_in6 mf6cc_origin;  /* Origin of mcast */
/usr/include/linux/mroute6.h:81:22: error: field 'mf6cc_mcastgrp' has incomplete type
  struct sockaddr_in6 mf6cc_mcastgrp;  /* Group in question */
/usr/include/linux/mroute6.h:91:22: error: field 'src' has incomplete type
  struct sockaddr_in6 src;
/usr/include/linux/mroute6.h:92:22: error: field 'grp' has incomplete type
  struct sockaddr_in6 grp;
/usr/include/linux/mroute6.h:132:18: error: field 'im6_src' has incomplete type
  struct in6_addr im6_src, im6_dst;
/usr/include/linux/mroute6.h:132:27: error: field 'im6_dst' has incomplete type
  struct in6_addr im6_src, im6_dst;

Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

uapi: fix linux/rds.h userspace compilation errors

[ Upstream commit feb0869d90e51ce8b6fd8a46588465b1b5a26d09 ]

Consistently use types from linux/types.h to fix the following
linux/rds.h userspace compilation errors:

/usr/include/linux/rds.h:106:2: error: unknown type name 'uint8_t'
  uint8_t name[32];
/usr/include/linux/rds.h:107:2: error: unknown type name 'uint64_t'
  uint64_t value;
/usr/include/linux/rds.h:117:2: error: unknown type name 'uint64_t'
  uint64_t next_tx_seq;
/usr/include/linux/rds.h:118:2: error: unknown type name 'uint64_t'
  uint64_t next_rx_seq;
/usr/include/linux/rds.h:121:2: error: unknown type name 'uint8_t'
  uint8_t transport[TRANSNAMSIZ];  /* null term ascii */
/usr/include/linux/rds.h:122:2: error: unknown type name 'uint8_t'
  uint8_t flags;
/usr/include/linux/rds.h:129:2: error: unknown type name 'uint64_t'
  uint64_t seq;
/usr/include/linux/rds.h:130:2: error: unknown type name 'uint32_t'
  uint32_t len;
/usr/include/linux/rds.h:135:2: error: unknown type name 'uint8_t'
  uint8_t flags;
/usr/include/linux/rds.h:139:2: error: unknown type name 'uint32_t'
  uint32_t sndbuf;
/usr/include/linux/rds.h:144:2: error: unknown type name 'uint32_t'
  uint32_t rcvbuf;
/usr/include/linux/rds.h:145:2: error: unknown type name 'uint64_t'
  uint64_t inum;
/usr/include/linux/rds.h:153:2: error: unknown type name 'uint64_t'
  uint64_t       hdr_rem;
/usr/include/linux/rds.h:154:2: error: unknown type name 'uint64_t'
  uint64_t       data_rem;
/usr/include/linux/rds.h:155:2: error: unknown type name 'uint32_t'
  uint32_t       last_sent_nxt;
/usr/include/linux/rds.h:156:2: error: unknown type name 'uint32_t'
  uint32_t       last_expected_una;
/usr/include/linux/rds.h:157:2: error: unknown type name 'uint32_t'
  uint32_t       last_seen_una;
/usr/include/linux/rds.h:164:2: error: unknown type name 'uint8_t'
  uint8_t  src_gid[RDS_IB_GID_LEN];
/usr/include/linux/rds.h:165:2: error: unknown type name 'uint8_t'
  uint8_t  dst_gid[RDS_IB_GID_LEN];
/usr/include/linux/rds.h:167:2: error: unknown type name 'uint32_t'
  uint32_t max_send_wr;
/usr/include/linux/rds.h:168:2: error: unknown type name 'uint32_t'
  uint32_t max_recv_wr;
/usr/include/linux/rds.h:169:2: error: unknown type name 'uint32_t'
  uint32_t max_send_sge;
/usr/include/linux/rds.h:170:2: error: unknown type name 'uint32_t'
  uint32_t rdma_mr_max;
/usr/include/linux/rds.h:171:2: error: unknown type name 'uint32_t'
  uint32_t rdma_mr_size;
/usr/include/linux/rds.h:212:9: error: unknown type name 'uint64_t'
 typedef uint64_t rds_rdma_cookie_t;
/usr/include/linux/rds.h:215:2: error: unknown type name 'uint64_t'
  uint64_t addr;
/usr/include/linux/rds.h:216:2: error: unknown type name 'uint64_t'
  uint64_t bytes;
/usr/include/linux/rds.h:221:2: error: unknown type name 'uint64_t'
  uint64_t cookie_addr;
/usr/include/linux/rds.h:222:2: error: unknown type name 'uint64_t'
  uint64_t flags;
/usr/include/linux/rds.h:228:2: error: unknown type name 'uint64_t'
  uint64_t  cookie_addr;
/usr/include/linux/rds.h:229:2: error: unknown type name 'uint64_t'
  uint64_t  flags;
/usr/include/linux/rds.h:234:2: error: unknown type name 'uint64_t'
  uint64_t flags;
/usr/include/linux/rds.h:240:2: error: unknown type name 'uint64_t'
  uint64_t local_vec_addr;
/usr/include/linux/rds.h:241:2: error: unknown type name 'uint64_t'
  uint64_t nr_local;
/usr/include/linux/rds.h:242:2: error: unknown type name 'uint64_t'
  uint64_t flags;
/usr/include/linux/rds.h:243:2: error: unknown type name 'uint64_t'
  uint64_t user_token;
/usr/include/linux/rds.h:248:2: error: unknown type name 'uint64_t'
  uint64_t  local_addr;
/usr/include/linux/rds.h:249:2: error: unknown type name 'uint64_t'
  uint64_t  remote_addr;
/usr/include/linux/rds.h:252:4: error: unknown type name 'uint64_t'
    uint64_t compare;
/usr/include/linux/rds.h:253:4: error: unknown type name 'uint64_t'
    uint64_t swap;
/usr/include/linux/rds.h:256:4: error: unknown type name 'uint64_t'
    uint64_t add;
/usr/include/linux/rds.h:259:4: error: unknown type name 'uint64_t'
    uint64_t compare;
/usr/include/linux/rds.h:260:4: error: unknown type name 'uint64_t'
    uint64_t swap;
/usr/include/linux/rds.h:261:4: error: unknown type name 'uint64_t'
    uint64_t compare_mask;
/usr/include/linux/rds.h:262:4: error: unknown type name 'uint64_t'
    uint64_t swap_mask;
/usr/include/linux/rds.h:265:4: error: unknown type name 'uint64_t'
    uint64_t add;
/usr/include/linux/rds.h:266:4: error: unknown type name 'uint64_t'
    uint64_t nocarry_mask;
/usr/include/linux/rds.h:269:2: error: unknown type name 'uint64_t'
  uint64_t flags;
/usr/include/linux/rds.h:270:2: error: unknown type name 'uint64_t'
  uint64_t user_token;
/usr/include/linux/rds.h:274:2: error: unknown type name 'uint64_t'
  uint64_t user_token;
/usr/include/linux/rds.h:275:2: error: unknown type name 'int32_t'
  int32_t  status;

Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ceph: clean up unsafe d_parent accesses in build_dentry_path

[ Upstream commit c6b0b656ca24ede6657abb4a2cd910fa9c1879ba ]

While we hold a reference to the dentry when build_dentry_path is
called, we could end up racing with a rename that changes d_parent.
Handle that situation correctly, by using the rcu_read_lock to
ensure that the parent dentry and inode stick around long enough
to safely check ceph_snap and ceph_ino.

Link: http://tracker.ceph.com/issues/18148
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Yan, Zheng <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i2c: at91: ensure state is restored after suspending

[ Upstream commit e3ccc921b7d8fd1fcd10a00720e09823d8078666 ]

When going to suspend, the I2C registers may be lost because the power to
VDDcore is cut. Restore them when resuming.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: mvpp2: release reference to txq_cpu[] entry after unmapping

[ Upstream commit 36fb7435b6ac4d288a2d4deea8934f9456ab46b6 ]

The mvpp2_txq_bufs_free() function is called upon TX completion to DMA
unmap TX buffers, and free the corresponding SKBs. It gets the
references to the SKB to free and the DMA buffer to unmap from a per-CPU
txq_pcpu data structure.

However, the code currently increments the pointer to the next entry
before doing the DMA unmap and freeing the SKB. It does not cause any
visible problem because for a given SKB the TX completion is guaranteed
to take place on the CPU where the TX was started. However, it is much
more logical to increment the pointer to the next entry once the current
entry has been completely unmapped/released.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: scsi_dh_emc: return success in clariion_std_inquiry()

[ Upstream commit 4d7d39a18b8b81511f0b893b7d2203790bf8a58b ]

We accidentally return an uninitialized variable on success.

Fixes: b6ff1b14cdf4 ("[SCSI] scsi_dh: Update EMC handler")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

slub: do not merge cache if slub_debug contains a never-merge flag

[ Upstream commit c6e28895a4372992961888ffaadc9efc643b5bfe ]

In case CONFIG_SLUB_DEBUG_ON=n, find_mergeable() gets debug features from
commandline but never checks if there are features from the
SLAB_NEVER_MERGE set.

As a result selected by slub_debug caches are always mergeable if they
have been created without a custom constructor set or without one of the
SLAB_* debug features on.

This moves the SLAB_NEVER_MERGE check below the flags update from
commandline to make sure it won't merge the slab cache if one of the debug
features is on.

Link: http://lkml.kernel.org/r/20170101124451.GA4740@lp-laptop-d
Signed-off-by: Grygorii Maistrenko <grygoriimkd@gmail.com>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ocfs2/dlmglue: prepare tracking logic to avoid recursive cluster lock

[ Upstream commit 439a36b8ef38657f765b80b775e2885338d72451 ]

We are in the situation that we have to avoid recursive cluster locking,
but there is no way to check if a cluster lock has been taken by a precess
already.

Mostly, we can avoid recursive locking by writing code carefully.
However, we found that it's very hard to handle the routines that are
invoked directly by vfs code.  For instance:

  const struct inode_operations ocfs2_file_iops = {
      .permission     = ocfs2_permission,
      .get_acl        = ocfs2_iop_get_acl,
      .set_acl        = ocfs2_iop_set_acl,
  };

Both ocfs2_permission() and ocfs2_iop_get_acl() call ocfs2_inode_lock(PR):

  do_sys_open
   may_open
    inode_permission
     ocfs2_permission
      ocfs2_inode_lock() <=== first time
       generic_permission
        get_acl
         ocfs2_iop_get_acl
   ocfs2_inode_lock() <=== recursive one

A deadlock will occur if a remote EX request comes in between two of
ocfs2_inode_lock().  Briefly describe how the deadlock is formed:

On one hand, OCFS2_LOCK_BLOCKED flag of this lockres is set in
BAST(ocfs2_generic_handle_bast) when downconvert is started on behalf of
the remote EX lock request.  Another hand, the recursive cluster lock
(the second one) will be blocked in in __ocfs2_cluster_lock() because of
OCFS2_LOCK_BLOCKED.  But, the downconvert never complete, why? because
there is no chance for the first cluster lock on this node to be
unlocked - we block ourselves in the code path.

The idea to fix this issue is mostly taken from gfs2 code.

1. introduce a new field: struct ocfs2_lock_res.l_holders, to keep track
   of the processes' pid who has taken the cluster lock of this lock
   resource;

2. introduce a new flag for ocfs2_inode_lock_full:
   OCFS2_META_LOCK_GETBH; it means just getting back disk inode bh for
   us if we've got cluster lock.

3. export a helper: ocfs2_is_locked_by_me() is used to check if we have
   got the cluster lock in the upper code path.

The tracking logic should be used by some of the ocfs2 vfs's callbacks,
to solve the recursive locking issue cuased by the fact that vfs
routines can call into each other.

The performance penalty of processing the holder list should only be
seen at a few cases where the tracking logic is used, such as get/set
acl.

You may ask what if the first time we got a PR lock, and the second time
we want a EX lock? fortunately, this case never happens in the real
world, as far as I can see, including permission check,
(get|set)_(acl|attr), and the gfs2 code also do so.

[sfr@canb.auug.org.au remove some inlines]
Link: http://lkml.kernel.org/r/20170117100948.11657-2-zren@suse.com
Signed-off-by: Eric Ren <zren@suse.com>
Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Joseph Qi <jiangqi903@gmail.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Mark Fasheh <mfasheh@versity.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: xts - Add ECB dependency

[ Upstream commit 12cb3a1c4184f891d965d1f39f8cfcc9ef617647 ]

Since the
   commit f1c131b45410a202eb45cc55980a7a9e4e4b4f40
   crypto: xts - Convert to skcipher
the XTS mode is based on ECB, so the mode must select
ECB otherwise it can fail to initialize.

Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx4_core: Fix VF overwrite of module param which disables DMFS on new probed PFs

[ Upstream commit 95f1ba9a24af9769f6e20dfe9a77c863f253f311 ]

In the VF driver, module parameter mlx4_log_num_mgm_entry_size was
mistakenly overwritten -- and in a manner which overrode the
device-managed flow steering option encoded in the parameter.

log_num_mgm_entry_size is a global module parameter which
affects all ConnectX-3 PFs installed on that host.
If a VF changes log_num_mgm_entry_size, this will affect all PFs
which are probed subsequent to the change (by disabling DMFS for
those PFs).

Fixes: 3c439b5586e9 ("mlx4_core: Allow choosing flow steering mode")
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sparc64: Migrate hvcons irq to panicked cpu

[ Upstream commit 7dd4fcf5b70694dc961eb6b954673e4fc9730dbd ]

On panic, all other CPUs are stopped except the one which had
hit panic. To keep console alive, we need to migrate hvcons irq
to panicked CPU.

Signed-off-by: Vijay Kumar <vijay.ac.kumar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

md/linear: shutup lockdep warnning

[ Upstream commit d939cdfde34f50b95254b375f498447c82190b3e ]

Commit 03a9e24(md linear: fix a race between linear_add() and
linear_congested()) introduces the warnning.

Acked-by: Coly Li <colyli@suse.de>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

f2fs: do not wait for writeback in write_begin

[ Upstream commit 86d54795c94532075d862aa0a79f0c981dab4bdd ]

Otherwise we can get livelock like below.

[79880.428136] dbench          D    0 18405  18404 0x00000000
[79880.428139] Call Trace:
[79880.428142]  __schedule+0x219/0x6b0
[79880.428144]  schedule+0x36/0x80
[79880.428147]  schedule_timeout+0x243/0x2e0
[79880.428152]  ? update_sd_lb_stats+0x16b/0x5f0
[79880.428155]  ? ktime_get+0x3c/0xb0
[79880.428157]  io_schedule_timeout+0xa6/0x110
[79880.428161]  __lock_page+0xf7/0x130
[79880.428164]  ? unlock_page+0x30/0x30
[79880.428167]  pagecache_get_page+0x16b/0x250
[79880.428171]  grab_cache_page_write_begin+0x20/0x40
[79880.428182]  f2fs_write_begin+0xa2/0xdb0 [f2fs]
[79880.428192]  ? f2fs_mark_inode_dirty_sync+0x16/0x30 [f2fs]
[79880.428197]  ? kmem_cache_free+0x79/0x200
[79880.428203]  ? __mark_inode_dirty+0x17f/0x360
[79880.428206]  generic_perform_write+0xbb/0x190
[79880.428213]  ? file_update_time+0xa4/0xf0
[79880.428217]  __generic_file_write_iter+0x19b/0x1e0
[79880.428226]  f2fs_file_write_iter+0x9c/0x180 [f2fs]
[79880.428231]  __vfs_write+0xc5/0x140
[79880.428235]  vfs_write+0xb2/0x1b0
[79880.428238]  SyS_write+0x46/0xa0
[79880.428242]  entry_SYSCALL_64_fastpath+0x1e/0xad

Fixes: cae96a5c8ab6 ("f2fs: check io submission more precisely")
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Btrfs: send, fix failure to rename top level inode due to name collision

[ Upstream commit 4dd9920d991745c4a16f53a8f615f706fbe4b3f7 ]

Under certain situations, an incremental send operation can fail due to a
premature attempt to create a new top level inode (a direct child of the
subvolume/snapshot root) whose name collides with another inode that was
removed from the send snapshot.

Consider the following example scenario.

Parent snapshot:

  .                 (ino 256, gen 8)
  |---- a1/         (ino 257, gen 9)
  |---- a2/         (ino 258, gen 9)

Send snapshot:

  .                 (ino 256, gen 3)
  |---- a2/         (ino 257, gen 7)

In this scenario, when receiving the incremental send stream, the btrfs
receive command fails like this (ran in verbose mode, -vv argument):

  rmdir a1
  mkfile o257-7-0
  rename o257-7-0 -> a2
  ERROR: rename o257-7-0 -> a2 failed: Is a directory

What happens when computing the incremental send stream is:

1) An operation to remove the directory with inode number 257 and
   generation 9 is issued.

2) An operation to create the inode with number 257 and generation 7 is
   issued. This creates the inode with an orphanized name of "o257-7-0".

3) An operation rename the new inode 257 to its final name, "a2", is
   issued. This is incorrect because inode 258, which has the same name
   and it's a child of the same parent (root inode 256), was not yet
   processed and therefore no rmdir operation for it was yet issued.
   The rename operation is issued because we fail to detect that the
   name of the new inode 257 collides with inode 258, because their
   parent, a subvolume/snapshot root (inode 256) has a different
   generation in both snapshots.

So fix this by ignoring the generation value of a parent directory that
matches a root inode (number 256) when we are checking if the name of the
inode currently being processed collides with the name of some other
inode that was not yet processed.

We can achieve this scenario of different inodes with the same number but
different generation values either by mounting a filesystem with the inode
cache option (-o inode_cache) or by creating and sending snapshots across
different filesystems, like in the following example:

  $ mkfs.btrfs -f /dev/sdb
  $ mount /dev/sdb /mnt
  $ mkdir /mnt/a1
  $ mkdir /mnt/a2
  $ btrfs subvolume snapshot -r /mnt /mnt/snap1
  $ btrfs send /mnt/snap1 -f /tmp/1.snap
  $ umount /mnt

  $ mkfs.btrfs -f /dev/sdc
  $ mount /dev/sdc /mnt
  $ touch /mnt/a2
  $ btrfs subvolume snapshot -r /mnt /mnt/snap2
  $ btrfs receive /mnt -f /tmp/1.snap
  # Take note that once the filesystem is created, its current
  # generation has value 7 so the inode from the second snapshot has
  # a generation value of 7. And after receiving the first snapshot
  # the filesystem is at a generation value of 10, because the call to
  # create the second snapshot bumps the generation to 8 (the snapshot
  # creation ioctl does a transaction commit), the receive command calls
  # the snapshot creation ioctl to create the first snapshot, which bumps
  # the filesystem's generation to 9, and finally when the receive
  # operation finishes it calls an ioctl to transition the first snapshot
  # (snap1) from RW mode to RO mode, which does another transaction commit
  # and bumps the filesystem's generation to 10.
  $ rm -f /tmp/1.snap
  $ btrfs send /mnt/snap1 -f /tmp/1.snap
  $ btrfs send -p /mnt/snap1 /mnt/snap2 -f /tmp/2.snap
  $ umount /mnt

  $ mkfs.btrfs -f /dev/sdd
  $ mount /dev/sdd /mnt
  $ btrfs receive /mnt /tmp/1.snap
  # Receive of snapshot snap2 used to fail.
  $ btrfs receive /mnt /tmp/2.snap

Signed-off-by: Robbie Ko <robbieko@synology.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
[Rewrote changelog to be more precise and clear]
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adc: xilinx: Fix error handling

[ Upstream commit ca1c39ef76376b67303d01f94fe98bb68bb3861a ]

Reorder error handling labels in order to match the way resources have
been allocated.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: nf_ct_expect: Change __nf_ct_expect_check() return value.

[ Upstream commit 4b86c459c7bee3acaf92f0e2b4c6ac803eaa1a58 ]

Commit 4dee62b1b9b4 ("netfilter: nf_ct_expect: nf_ct_expect_insert()
returns void") inadvertently changed the successful return value of
nf_ct_expect_related_report() from 0 to 1 due to
__nf_ct_expect_check() returning 1 on success.  Prevent this
regression in the future by changing the return value of
__nf_ct_expect_check() to 0 on success.

Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx4_en: fix overflow in mlx4_en_init_timestamp()

[ Upstream commit 47d3a07528ecbbccf53bc4390d70b4e3d1c04fcf ]

The cited commit makes a great job of finding optimal shift/multiplier
values assuming a 10 seconds wrap around, but forgot to change the
overflow_period computation.

It overflows in cyclecounter_cyc2ns(), and the final result is 804 ms,
which is silly.

Lets simply use 5 seconds, no need to recompute this, given how it is
supposed to work.

Later, we will use a timer instead of a work queue, since the new RX
allocation schem will no longer need mlx4_en_recover_from_oom() and the
service_task firing every 250 ms.

Fixes: 31c128b66e5b ("net/mlx4_en: Choose time-stamping shift value according to HW frequency")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: fix power saving clients handling in iwlwifi

[ Upstream commit d98937f4ea713d21e0fcc345919f86c877dd8d6f ]

iwlwifi now supports RSS and can't let mac80211 track the
PS state based on the Rx frames since they can come out of
order. iwlwifi is now advertising AP_LINK_PS, and uses
explicit notifications to teach mac80211 about the PS state
of the stations and the PS poll / uAPSD trigger frames
coming our way from the peers.

Because of that, the TIM stopped being maintained in
mac80211. I tried to fix this in commit c68df2e7be0c
("mac80211: allow using AP_LINK_PS with mac80211-generated TIM IE")
but that was later reverted by Felix in commit 6c18a6b4e799
("Revert "mac80211: allow using AP_LINK_PS with mac80211-generated TIM IE")
since it broke drivers that do not implement set_tim.

Since none of the drivers that set AP_LINK_PS have the
set_tim() handler set besides iwlwifi, I can bail out in
__sta_info_recalc_tim if AP_LINK_PS AND .set_tim is not
implemented.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211_hwsim: check HWSIM_ATTR_RADIO_NAME length

[ Upstream commit ff4dd73dd2b4806419f8ff65cbce11d5019548d0 ]

Unfortunately, the nla policy was defined to have HWSIM_ATTR_RADIO_NAME
as an NLA_STRING, rather than NLA_NUL_STRING, so we can't use it as a
NUL-terminated string in the kernel.

Rather than break the API, kasprintf() the string to a new buffer to
guarantee NUL termination.

Reported-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

irqchip/crossbar: Fix incorrect type of local variables

[ Upstream commit b28ace12661fbcfd90959c1e84ff5a85113a82a1 ]

The max and entry variables are unsigned according to the dt-bindings.
Fix following 3 sparse issues (-Wtypesign):

  drivers/irqchip/irq-crossbar.c:222:52: warning: incorrect type in argument 3 (different signedness)
  drivers/irqchip/irq-crossbar.c:222:52:    expected unsigned int [usertype] *out_value
  drivers/irqchip/irq-crossbar.c:222:52:    got int *<noident>

  drivers/irqchip/irq-crossbar.c:245:56: warning: incorrect type in argument 4 (different signedness)
  drivers/irqchip/irq-crossbar.c:245:56:    expected unsigned int [usertype] *out_value
  drivers/irqchip/irq-crossbar.c:245:56:    got int *<noident>

  drivers/irqchip/irq-crossbar.c:263:56: warning: incorrect type in argument 4 (different signedness)
  drivers/irqchip/irq-crossbar.c:263:56:    expected unsigned int [usertype] *out_value
  drivers/irqchip/irq-crossbar.c:263:56:    got int *<noident>

Signed-off-by: Franck Demathieu <fdemathieu@gmail.com>
Cc: marc.zyngier@arm.com
Cc: jason@lakedaemon.net
Link: http://lkml.kernel.org/r/20170223094855.6546-1-fdemathieu@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

watchdog: kempld: fix gcc-4.3 build

[ Upstream commit 3736d4eb6af37492aeded7fec0072dedd959c842 ]

gcc-4.3 can't decide whether the constant value in
kempld_prescaler[PRESCALER_21] is built-time constant or
not, and gets confused by the logic in do_div():

drivers/watchdog/kempld_wdt.o: In function `kempld_wdt_set_stage_timeout':
kempld_wdt.c:(.text.kempld_wdt_set_stage_timeout+0x130): undefined reference to `__aeabi_uldivmod'

This adds a call to ACCESS_ONCE() to force it to not consider
it to be constant, and leaves the more efficient normal case
in place for modern compilers, using an #ifdef to annotate
why we do this hack.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

locking/lockdep: Add nest_lock integrity test

[ Upstream commit 7fb4a2cea6b18dab56d609530d077f168169ed6b ]

Boqun reported that hlock->references can overflow. Add a debug test
for that to generate a clear error when this happens.

Without this, lockdep is likely to report a mysterious failure on
unlock.

Reported-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nicolai Hähnle <Nicolai.Haehnle@amd.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "bsg-lib: don't free job in bsg_prepare_job"

This reverts commit 668cee82cd28d2c38a99f7cbddf3b3fd58f257b9 which was
commit f507b54dccfd8000c517d740bc45f20c74532d18 upstream.

Ben reports:
That function doesn't exist here (it was introduced in 4.13).
Instead, this backport has modified bsg_create_job(), creating a
leak.  Please revert this on the 3.18, 4.4 and 4.9 stable
branches.

So I'm dropping it from here.

Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org

tipc: use only positive error codes in messages

[ Upstream commit aad06212d36cf34859428a0a279e5c14ee5c9e26 ]

In commit e3a77561e7d32 ("tipc: split up function tipc_msg_eval()"),
we have updated the function tipc_msg_lookup_dest() to set the error
codes to negative values at destination lookup failures. Thus when
the function sets the error code to -TIPC_ERR_NO_NAME, its inserted
into the 4 bit error field of the message header as 0xf instead of
TIPC_ERR_NO_NAME (1). The value 0xf is an unknown error code.

In this commit, we set only positive error code.

Fixes: e3a77561e7d32 ("tipc: split up function tipc_msg_eval()")
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: Set sk_prot_creator when cloning sockets to the right proto

[ Upstream commit 9d538fa60bad4f7b23193c89e843797a1cf71ef3 ]

sk->sk_prot and sk->sk_prot_creator can differ when the app uses
IPV6_ADDRFORM (transforming an IPv6-socket to an IPv4-one).
Which is why sk_prot_creator is there to make sure that sk_prot_free()
does the kmem_cache_free() on the right kmem_cache slab.

Now, if such a socket gets transformed back to a listening socket (using
connect() with AF_UNSPEC) we will allocate an IPv4 tcp_sock through
sk_clone_lock() when a new connection comes in. But sk_prot_creator will
still point to the IPv6 kmem_cache (as everything got copied in
sk_clone_lock()). When freeing, we will thus put this
memory back into the IPv6 kmem_cache although it was allocated in the
IPv4 cache. I have seen memory corruption happening because of this.

With slub-debugging and MEMCG_KMEM enabled this gives the warning
"cache_from_obj: Wrong slab cache. TCPv6 but object is from TCP"

A C-program to trigger this:

void main(void)
{
        int fd = socket(AF_INET6, SOCK_STREAM, IPPROTO_TCP);
        int new_fd, newest_fd, client_fd;
        struct sockaddr_in6 bind_addr;
        struct sockaddr_in bind_addr4, client_addr1, client_addr2;
        struct sockaddr unsp;
        int val;

        memset(&bind_addr, 0, sizeof(bind_addr));
        bind_addr.sin6_family = AF_INET6;
        bind_addr.sin6_port = ntohs(42424);

        memset(&client_addr1, 0, sizeof(client_addr1));
        client_addr1.sin_family = AF_INET;
        client_addr1.sin_port = ntohs(42424);
        client_addr1.sin_addr.s_addr = inet_addr("127.0.0.1");

        memset(&client_addr2, 0, sizeof(client_addr2));
        client_addr2.sin_family = AF_INET;
        client_addr2.sin_port = ntohs(42421);
        client_addr2.sin_addr.s_addr = inet_addr("127.0.0.1");

        memset(&unsp, 0, sizeof(unsp));
        unsp.sa_family = AF_UNSPEC;

        bind(fd, (struct sockaddr *)&bind_addr, sizeof(bind_addr));

        listen(fd, 5);

        client_fd = socket(AF_INET, SOCK_STREAM, IPPROTO_TCP);
        connect(client_fd, (struct sockaddr *)&client_addr1, sizeof(client_addr1));
        new_fd = accept(fd, NULL, NULL);
        close(fd);

        val = AF_INET;
        setsockopt(new_fd, SOL_IPV6, IPV6_ADDRFORM, &val, sizeof(val));

        connect(new_fd, &unsp, sizeof(unsp));

        memset(&bind_addr4, 0, sizeof(bind_addr4));
        bind_addr4.sin_family = AF_INET;
        bind_addr4.sin_port = ntohs(42421);
        bind(new_fd, (struct sockaddr *)&bind_addr4, sizeof(bind_addr4));

        listen(new_fd, 5);

        client_fd = socket(AF_INET, SOCK_STREAM, IPPROTO_TCP);
        connect(client_fd, (struct sockaddr *)&client_addr2, sizeof(client_addr2));

        newest_fd = accept(new_fd, NULL, NULL);
        close(new_fd);

        close(client_fd);
        close(new_fd);
}

As far as I can see, this bug has been there since the beginning of the
git-days.

Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

packet: only test po->has_vnet_hdr once in packet_snd

[ Upstream commit da7c9561015e93d10fe6aab73e9288e0d09d65a6 ]

Packet socket option po->has_vnet_hdr can be updated concurrently with
other operations if no ring is attached.

Do not test the option twice in packet_snd, as the value may change in
between calls. A race on setsockopt disable may cause a packet > mtu
to be sent without having GSO options set.

Fixes: bfd5f4a3d605 ("packet: Add GSO/csum offload support.")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

packet: in packet_do_bind, test fanout with bind_lock held

[ Upstream commit 4971613c1639d8e5f102c4e797c3bf8f83a5a69e ]

Once a socket has po->fanout set, it remains a member of the group
until it is destroyed. The prot_hook must be constant and identical
across sockets in the group.

If fanout_add races with packet_do_bind between the test of po->fanout
and taking the lock, the bind call may make type or dev inconsistent
with that of the fanout group.

Hold po->bind_lock when testing po->fanout to avoid this race.

I had to introduce artificial delay (local_bh_enable) to actually
observe the race.

Fixes: dc99f600698d ("packet: Add fanout support.")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tun: bail out from tun_get_user() if the skb is empty

[ Upstream commit 2580c4c17aee3ad58e9751012bad278dd074ccae ]

KMSAN (https://github.com/google/kmsan) reported accessing uninitialized
skb->data[0] in the case the skb is empty (i.e. skb->len is 0):

================================================
BUG: KMSAN: use of uninitialized memory in tun_get_user+0x19ba/0x3770
CPU: 0 PID: 3051 Comm: probe Not tainted 4.13.0+ #3140
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
...
 __msan_warning_32+0x66/0xb0 mm/kmsan/kmsan_instr.c:477
 tun_get_user+0x19ba/0x3770 drivers/net/tun.c:1301
 tun_chr_write_iter+0x19f/0x300 drivers/net/tun.c:1365
 call_write_iter ./include/linux/fs.h:1743
 new_sync_write fs/read_write.c:457
 __vfs_write+0x6c3/0x7f0 fs/read_write.c:470
 vfs_write+0x3e4/0x770 fs/read_write.c:518
 SYSC_write+0x12f/0x2b0 fs/read_write.c:565
 SyS_write+0x55/0x80 fs/read_write.c:557
 do_syscall_64+0x242/0x330 arch/x86/entry/common.c:284
 entry_SYSCALL64_slow_path+0x25/0x25 arch/x86/entry/entry_64.S:245
...
origin:
...
 kmsan_poison_shadow+0x6e/0xc0 mm/kmsan/kmsan.c:211
 slab_alloc_node mm/slub.c:2732
 __kmalloc_node_track_caller+0x351/0x370 mm/slub.c:4351
 __kmalloc_reserve net/core/skbuff.c:138
 __alloc_skb+0x26a/0x810 net/core/skbuff.c:231
 alloc_skb ./include/linux/skbuff.h:903
 alloc_skb_with_frags+0x1d7/0xc80 net/core/skbuff.c:4756
 sock_alloc_send_pskb+0xabf/0xfe0 net/core/sock.c:2037
 tun_alloc_skb drivers/net/tun.c:1144
 tun_get_user+0x9a8/0x3770 drivers/net/tun.c:1274
 tun_chr_write_iter+0x19f/0x300 drivers/net/tun.c:1365
 call_write_iter ./include/linux/fs.h:1743
 new_sync_write fs/read_write.c:457
 __vfs_write+0x6c3/0x7f0 fs/read_write.c:470
 vfs_write+0x3e4/0x770 fs/read_write.c:518
 SYSC_write+0x12f/0x2b0 fs/read_write.c:565
 SyS_write+0x55/0x80 fs/read_write.c:557
 do_syscall_64+0x242/0x330 arch/x86/entry/common.c:284
 return_from_SYSCALL_64+0x0/0x6a arch/x86/entry/entry_64.S:245
================================================

Make sure tun_get_user() doesn't touch skb->data[0] unless there is
actual data.

C reproducer below:
==========================
    // autogenerated by syzkaller (http://github.com/google/syzkaller)

    #define _GNU_SOURCE

    #include <fcntl.h>
    #include <linux/if_tun.h>
    #include <netinet/ip.h>
    #include <net/if.h>
    #include <string.h>
    #include <sys/ioctl.h>

    int main()
    {
      int sock = socket(PF_INET, SOCK_STREAM, IPPROTO_IP);
      int tun_fd = open("/dev/net/tun", O_RDWR);
      struct ifreq req;
      memset(&req, 0, sizeof(struct ifreq));
      strcpy((char*)&req.ifr_name, "gre0");
      req.ifr_flags = IFF_UP | IFF_MULTICAST;
      ioctl(tun_fd, TUNSETIFF, &req);
      ioctl(sock, SIOCSIFFLAGS, "gre0");
      write(tun_fd, "hi", 0);
      return 0;
    }
==========================

Signed-off-by: Alexander Potapenko <glider@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

l2tp: fix race condition in l2tp_tunnel_delete

[ Upstream commit 62b982eeb4589b2e6d7c01a90590e3a4c2b2ca19 ]

If we try to delete the same tunnel twice, the first delete operation
does a lookup (l2tp_tunnel_get), finds the tunnel, calls
l2tp_tunnel_delete, which queues it for deletion by
l2tp_tunnel_del_work.

The second delete operation also finds the tunnel and calls
l2tp_tunnel_delete. If the workqueue has already fired and started
running l2tp_tunnel_del_work, then l2tp_tunnel_delete will queue the
same tunnel a second time, and try to free the socket again.

Add a dead flag to prevent firing the workqueue twice. Then we can
remove the check of queue_work's result that was meant to prevent that
race but doesn't.

Reproducer:

    ip l2tp add tunnel tunnel_id 3000 peer_tunnel_id 4000 local 192.168.0.2 remote 192.168.0.1 encap udp udp_sport 5000 udp_dport 6000
    ip l2tp add session name l2tp1 tunnel_id 3000 session_id 1000 peer_session_id 2000
    ip link set l2tp1 up
    ip l2tp del tunnel tunnel_id 3000
    ip l2tp del tunnel tunnel_id 3000

Fixes: f8ccac0e4493 ("l2tp: put tunnel socket release on a workqueue")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

l2tp: Avoid schedule while atomic in exit_net

[ Upstream commit 12d656af4e3d2781b9b9f52538593e1717e7c979 ]

While destroying a network namespace that contains a L2TP tunnel a
"BUG: scheduling while atomic" can be observed.

Enabling lockdep shows that this is happening because l2tp_exit_net()
is calling l2tp_tunnel_closeall() (via l2tp_tunnel_delete()) from
within an RCU critical section.

l2tp_exit_net() takes rcu_read_lock_bh()
  << list_for_each_entry_rcu() >>
  l2tp_tunnel_delete()
    l2tp_tunnel_closeall()
      __l2tp_session_unhash()
        synchronize_rcu() << Illegal inside RCU critical section >>

BUG: sleeping function called from invalid context
in_atomic(): 1, irqs_disabled(): 0, pid: 86, name: kworker/u16:2
INFO: lockdep is turned off.
CPU: 2 PID: 86 Comm: kworker/u16:2 Tainted: G        W  O    4.4.6-at1 #2
Hardware name: Xen HVM domU, BIOS 4.6.1-xs125300 05/09/2016
Workqueue: netns cleanup_net
 0000000000000000 ffff880202417b90 ffffffff812b0013 ffff880202410ac0
 ffffffff81870de8 ffff880202417bb8 ffffffff8107aee8 ffffffff81870de8
 0000000000000c51 0000000000000000 ffff880202417be0 ffffffff8107b024
Call Trace:
 [<ffffffff812b0013>] dump_stack+0x85/0xc2
 [<ffffffff8107aee8>] ___might_sleep+0x148/0x240
 [<ffffffff8107b024>] __might_sleep+0x44/0x80
 [<ffffffff810b21bd>] synchronize_sched+0x2d/0xe0
 [<ffffffff8109be6d>] ? trace_hardirqs_on+0xd/0x10
 [<ffffffff8105c7bb>] ? __local_bh_enable_ip+0x6b/0xc0
 [<ffffffff816a1b00>] ? _raw_spin_unlock_bh+0x30/0x40
 [<ffffffff81667482>] __l2tp_session_unhash+0x172/0x220
 [<ffffffff81667397>] ? __l2tp_session_unhash+0x87/0x220
 [<ffffffff8166888b>] l2tp_tunnel_closeall+0x9b/0x140
 [<ffffffff81668c74>] l2tp_tunnel_delete+0x14/0x60
 [<ffffffff81668dd0>] l2tp_exit_net+0x110/0x270
 [<ffffffff81668d5c>] ? l2tp_exit_net+0x9c/0x270
 [<ffffffff815001c3>] ops_exit_list.isra.6+0x33/0x60
 [<ffffffff81501166>] cleanup_net+0x1b6/0x280
 ...

This bug can easily be reproduced with a few steps:

 $ sudo unshare -n bash  # Create a shell in a new namespace
 # ip link set lo up
 # ip addr add 127.0.0.1 dev lo
 # ip l2tp add tunnel remote 127.0.0.1 local 127.0.0.1 tunnel_id 1 \
    peer_tunnel_id 1 udp_sport 50000 udp_dport 50000
 # ip l2tp add session name foo tunnel_id 1 session_id 1 \
    peer_session_id 1
 # ip link set foo up
 # exit  # Exit the shell, in turn exiting the namespace
 $ dmesg
 ...
 [942121.089216] BUG: scheduling while atomic: kworker/u16:3/13872/0x00000200
 ...

To fix this, move the call to l2tp_tunnel_closeall() out of the RCU
critical section, and instead call it from l2tp_tunnel_del_work(), which
is running from the l2tp_wq workqueue.

Fixes: 2b551c6e7d5b ("l2tp: close sessions before initiating tunnel delete")
Signed-off-by: Ridge Kennedy <ridge.kennedy@alliedtelesis.co.nz>
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vti: fix use after free in vti_tunnel_xmit/vti6_tnl_xmit

[ Upstream commit 36f6ee22d2d66046e369757ec6bbe1c482957ba6 ]

When running LTP IPsec tests, KASan might report:

BUG: KASAN: use-after-free in vti_tunnel_xmit+0xeee/0xff0 [ip_vti]
Read of size 4 at addr ffff880dc6ad1980 by task swapper/0/0
...
Call Trace:
  <IRQ>
  dump_stack+0x63/0x89
  print_address_description+0x7c/0x290
  kasan_report+0x28d/0x370
  ? vti_tunnel_xmit+0xeee/0xff0 [ip_vti]
  __asan_report_load4_noabort+0x19/0x20
  vti_tunnel_xmit+0xeee/0xff0 [ip_vti]
  ? vti_init_net+0x190/0x190 [ip_vti]
  ? save_stack_trace+0x1b/0x20
  ? save_stack+0x46/0xd0
  dev_hard_start_xmit+0x147/0x510
  ? icmp_echo.part.24+0x1f0/0x210
  __dev_queue_xmit+0x1394/0x1c60
...
Freed by task 0:
  save_stack_trace+0x1b/0x20
  save_stack+0x46/0xd0
  kasan_slab_free+0x70/0xc0
  kmem_cache_free+0x81/0x1e0
  kfree_skbmem+0xb1/0xe0
  kfree_skb+0x75/0x170
  kfree_skb_list+0x3e/0x60
  __dev_queue_xmit+0x1298/0x1c60
  dev_queue_xmit+0x10/0x20
  neigh_resolve_output+0x3a8/0x740
  ip_finish_output2+0x5c0/0xe70
  ip_finish_output+0x4ba/0x680
  ip_output+0x1c1/0x3a0
  xfrm_output_resume+0xc65/0x13d0
  xfrm_output+0x1e4/0x380
  xfrm4_output_finish+0x5c/0x70

Can be fixed if we get skb->len before dst_output().

Fixes: b9959fd3b0fa ("vti: switch to new ip tunnel code")
Fixes: 22e1b23dafa8 ("vti6: Support inter address family tunneling.")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

isdn/i4l: fetch the ppp_write buffer in one shot

[ Upstream commit 02388bf87f72e1d47174cd8f81c34443920eb5a0 ]

In isdn_ppp_write(), the header (i.e., protobuf) of the buffer is
fetched twice from userspace. The first fetch is used to peek at the
protocol of the message and reset the huptimer if necessary; while the
second fetch copies in the whole buffer. However, given that buf resides
in userspace memory, a user process can race to change its memory content
across fetches. By doing so, we can either avoid resetting the huptimer
for any type of packets (by first setting proto to PPP_LCP and later
change to the actual type) or force resetting the huptimer for LCP
packets.

This patch changes this double-fetch behavior into two single fetches
decided by condition (lp->isdn_device < 0 || lp->isdn_channel <0).
A more detailed discussion can be found at
https://marc.info/?l=linux-kernel&m=150586376926123&w=2

Signed-off-by: Meng Xu <mengxu.gatech@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bpf: one perf event close won't free bpf program attached by another perf event

[ Upstream commit ec9dd352d591f0c90402ec67a317c1ed4fb2e638 ]

This patch fixes a bug exhibited by the following scenario:
  1. fd1 = perf_event_open with attr.config = ID1
  2. attach bpf program prog1 to fd1
  3. fd2 = perf_event_open with attr.config = ID1
     <this will be successful>
  4. user program closes fd2 and prog1 is detached from the tracepoint.
  5. user program with fd1 does not work properly as tracepoint
     no output any more.

The issue happens at step 4. Multiple perf_event_open can be called
successfully, but only one bpf prog pointer in the tp_event. In the
current logic, any fd release for the same tp_event will free
the tp_event->prog.

The fix is to free tp_event->prog only when the closing fd
corresponds to the one which registered the program.

Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

packet: hold bind lock when rebinding to fanout hook

[ Upstream commit 008ba2a13f2d04c947adc536d19debb8fe66f110 ]

Packet socket bind operations must hold the po->bind_lock. This keeps
po->running consistent with whether the socket is actually on a ptype
list to receive packets.

fanout_add unbinds a socket and its packet_rcv/tpacket_rcv call, then
binds the fanout object to receive through packet_rcv_fanout.

Make it hold the po->bind_lock when testing po->running and rebinding.
Else, it can race with other rebind operations, such as that in
packet_set_ring from packet_rcv to tpacket_rcv. Concurrent updates
can result in a socket being added to a fanout group twice, causing
use-after-free KASAN bug reports, among others.

Reported independently by both trinity and syzkaller.
Verified that the syzkaller reproducer passes after this patch.

Fixes: dc99f600698d ("packet: Add fanout support.")
Reported-by: nixioaming <nixiaoming@huawei.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: emac: Fix napi poll list corruption

[ Upstream commit f55956065ec94e3e9371463d693a1029c4cc3007 ]

This patch is pretty much a carbon copy of
commit 3079c652141f ("caif: Fix napi poll list corruption")
with "caif" replaced by "emac".

The commit d75b1ade567f ("net: less interrupt masking in NAPI")
breaks emac.

It is now required that if the entire budget is consumed when poll
returns, the napi poll_list must remain empty.  However, like some
other drivers emac tries to do a last-ditch check and if there is
more work it will call napi_reschedule and then immediately process
some of this new work.  Should the entire budget be consumed while
processing such new work then we will violate the new caller
contract.

This patch fixes this by not touching any work when we reschedule
in emac.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ip6_gre: skb_push ipv6hdr before packing the header in ip6gre_header

[ Upstream commit 76cc0d3282d4b933fa144fa41fbc5318e0fdca24 ]

Now in ip6gre_header before packing the ipv6 header, it skb_push t->hlen
which only includes encap_hlen + tun_hlen. It means greh and inner header
would be over written by ipv6 stuff and ipv6h might have no chance to set
up.

Jianlin found this issue when using remote any on ip6_gre, the packets he
captured on gre dev are truncated:

22:50:26.210866 Out ethertype IPv6 (0x86dd), length 120: truncated-ip6 -\
8128 bytes missing!(flowlabel 0x92f40, hlim 0, next-header Options (0)  \
payload length: 8192) ::1:2000:0 > ::1:0:86dd: HBH [trunc] ip-proto-128 \
8184

It should also skb_push ipv6hdr so that ipv6h points to the right position
to set ipv6 stuff up.

This patch is to skb_push hlen + sizeof(*ipv6h) and also fix some indents
in ip6gre_header.

Fixes: c12b395a4664 ("gre: Support GRE over IPv6")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

udpv6: Fix the checksum computation when HW checksum does not apply

[ Upstream commit 63ecc3d9436f8012e49dc846d6cb0a85a3433517 ]

While trying an ESP transport mode encryption for UDPv6 packets of
datagram size 1436 with MTU 1500, checksum error was observed in
the secondary fragment.

This error occurs due to the UDP payload checksum being missed out
when computing the full checksum for these packets in
udp6_hwcsum_outgoing().

Fixes: d39d938c8228 ("ipv6: Introduce udpv6_send_skb()")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bpf/verifier: reject BPF_ALU64|BPF_END

[ Upstream commit e67b8a685c7c984e834e3181ef4619cd7025a136 ]

Neither ___bpf_prog_run nor the JITs accept it.
Also adds a new test case.

Fixes: 17a5267067f3 ("bpf: verifier (add verifier core)")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sctp: potential read out of bounds in sctp_ulpevent_type_enabled()

[ Upstream commit fa5f7b51fc3080c2b195fa87c7eca7c05e56f673 ]

This code causes a static checker warning because Smatch doesn't trust
anything that comes from skb->data.  I've reviewed this code and I do
think skb->data can be controlled by the user here.

The sctp_event_subscribe struct has 13 __u8 fields and we want to see
if ours is non-zero.  sn_type can be any value in the 0-USHRT_MAX range.
We're subtracting SCTP_SN_TYPE_BASE which is 1 << 15 so we could read
either before the start of the struct or after the end.

This is a very old bug and it's surprising that it would go undetected
for so long but my theory is that it just doesn't have a big impact so
it would be hard to notice.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Fix minimum alignment requirement of IRQ stack

commit 5fdc66e046206306bf61ff2d626bfa52ca087f7b upstream.

Commit db8466c581cc ("MIPS: IRQ Stack: Unwind IRQ stack onto task
stack") erroneously set the initial stack pointer of the IRQ stack to a
value with a 4 byte alignment. The MIPS32 ABI requires that the minimum
stack alignment is 8 byte, and the MIPS64 ABIs(n32/n64) require 16 byte
minimum alignment. Fix IRQ_STACK_START such that it leaves space for the
dummy stack frame (containing interrupted task kernel stack pointer)
while also meeting minimum alignment requirements.

Fixes: db8466c581cc ("MIPS: IRQ Stack: Unwind IRQ stack onto task stack")
Reported-by: Darius Ivanauskas <dasilt@yahoo.com>
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Jason A. Donenfeld <jason@zx2c4.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16760/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/dp/mst: save vcpi with payloads

commit 6cecdf7a161d2b909dc7c8979176bbc4f0669968 upstream.

This makes it possibly for drivers to find the associated
mst_port by looking at the payload allocation table.

Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449514552-10236-3-git-send-email-harry.wentland@amd.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Kai Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

percpu: make this_cpu_generic_read() atomic w.r.t. interrupts

commit e88d62cd4b2f0b1ae55e9008e79c2794b1fc914d upstream.

As raw_cpu_generic_read() is a plain read from a raw_cpu_ptr() address,
it's possible (albeit unlikely) that the compiler will split the access
across multiple instructions.

In this_cpu_generic_read() we disable preemption but not interrupts
before calling raw_cpu_generic_read(). Thus, an interrupt could be taken
in the middle of the split load instructions. If a this_cpu_write() or
RMW this_cpu_*() op is made to the same variable in the interrupt
handling path, this_cpu_read() will return a torn value.

For native word types, we can avoid tearing using READ_ONCE(), but this
won't work in all cases (e.g. 64-bit types on most 32-bit platforms).
This patch reworks this_cpu_generic_read() to use READ_ONCE() where
possible, otherwise falling back to disabling interrupts.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Lameter <cl@linux.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Pranith Kumar <bobby.prani@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
[Mark: backport to v4.4.y]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.4.93

x86/alternatives: Fix alt_max_short macro to really be a max()

commit 6b32c126d33d5cb379bca280ab8acedc1ca978ff upstream.

The alt_max_short() macro in asm/alternative.h does not work as
intended, leading to nasty bugs. E.g. alt_max_short("1", "3")
evaluates to 3, but alt_max_short("3", "1") evaluates to 1 -- not
exactly the maximum of 1 and 3.

In fact, I had to learn it the hard way by crashing my kernel in not
so funny ways by attempting to make use of the ALTENATIVE_2 macro
with alternatives where the first one was larger than the second
one.

According to [1] and commit dbe4058a6a44 ("x86/alternatives: Fix
ALTERNATIVE_2 padding generation properly") the right handed side
should read "-(-(a < b))" not "-(-(a - b))". Fix that, to make the
macro work as intended.

While at it, fix up the comments regarding the additional "-", too.
It's not about gas' usage of s32 but brain dead logic of having a
"true" value of -1 for the < operator ... *sigh*

Btw., the one in asm/alternative-asm.h is correct. And, apparently,
all current users of ALTERNATIVE_2() pass same sized alternatives,
avoiding to hit the bug.

[1] http://graphics.stanford.edu/~seander/bithacks.html#IntegerMinOrMax

Reviewed-and-tested-by: Borislav Petkov <bp@suse.de>
Fixes: dbe4058a6a44 ("x86/alternatives: Fix ALTERNATIVE_2 padding generation properly")
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/1507228213-13095-1-git-send-email-minipli@googlemail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: console: fix use-after-free after failed setup

commit 299d7572e46f98534033a9e65973f13ad1ce9047 upstream.

Make sure to reset the USB-console port pointer when console setup fails
in order to avoid having the struct usb_serial be prematurely freed by
the console code when the device is later disconnected.

Fixes: 73e487fdb75f ("[PATCH] USB console: fix disconnection issues")
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: qcserial: add Dell DW5818, DW5819

commit f5d9644c5fca7d8e8972268598bb516a7eae17f9 upstream.

Dell Wireless 5819/5818 devices are re-branded Sierra Wireless MC74
series which will by default boot with vid 0x413c and pid's 0x81cf,
0x81d0, 0x81d1, 0x81d2.

Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: option: add support for TP-Link LTE module

commit 837ddc4793a69b256ac5e781a5e729b448a8d983 upstream.

This commit adds support for TP-Link LTE mPCIe module is used
in in TP-Link MR200v1, MR6400v1 and v2 routers.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: cp210x: add support for ELV TFD500

commit c496ad835c31ad639b6865714270b3003df031f6 upstream.

Add the USB device id for the ELV TFD500 data logger.

Signed-off-by: Andreas Engel <anen-nospam@gmx.net>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: ftdi_sio: add id for Cypress WICED dev board

commit a6c215e21b0dc5fe9416dce90f9acc2ea53c4502 upstream.

Add CYPRESS_VID vid and CYPRESS_WICED_BT_USB and CYPRESS_WICED_WL_USB
device IDs to ftdi_sio driver.

Signed-off-by: Jeffrey Chu <jeffrey.chu@cypress.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fix unbalanced page refcounting in bio_map_user_iov

commit 95d78c28b5a85bacbc29b8dba7c04babb9b0d467 upstream.

bio_map_user_iov and bio_unmap_user do unbalanced pages refcounting if
IO vector has small consecutive buffers belonging to the same page.
bio_add_pc_page merges them into one, but the page reference is never
dropped.

Signed-off-by: Vitaly Mayatskikh <v.mayatskih@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

direct-io: Prevent NULL pointer access in submit_page_section

commit 899f0429c7d3eed886406cd72182bee3b96aa1f9 upstream.

In the code added to function submit_page_section by commit b1058b981,
sdio->bio can currently be NULL when calling dio_bio_submit.  This then
leads to a NULL pointer access in dio_bio_submit, so check for a NULL
bio in submit_page_section before trying to submit it instead.

Fixes xfstest generic/250 on gfs2.

Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: composite: Fix use-after-free in usb_composite_overwrite_options

commit aec17e1e249567e82b26dafbb86de7d07fde8729 upstream.

KASAN enabled configuration reports an error

    BUG: KASAN: use-after-free in usb_composite_overwrite_options+...
                [libcomposite] at addr ...
    Read of size 1 by task ...

when some driver is un-bound and then bound again.
For example, this happens with FunctionFS driver when "ffs-test"
test application is run several times in a row.

If the driver has empty manufacturer ID string in initial static data,
it is then replaced with generated string. After driver unbinding
the generated string is freed, but the driver data still keep that
pointer. And if the driver is then bound again, that pointer
is re-used for string emptiness check.

The fix is to clean up the driver string data upon its unbinding
to drop the pointer to freed memory.

Fixes: cc2683c318a5 ("usb: gadget: Provide a default implementation of default manufacturer string")
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: line6: Fix leftover URB at error-path during probe

commit c95072b3d88fac4be295815f2b67df366c0c297f upstream.

While line6_probe() may kick off URB for a control MIDI endpoint, the
function doesn't clean up it properly at its error path.  This results
in a leftover URB action that is eventually triggered later and causes
an Oops like:
  general protection fault: 0000 [#1] PREEMPT SMP KASAN
  CPU: 1 PID: 0 Comm: swapper/1 Not tainted
  RIP: 0010:usb_fill_bulk_urb ./include/linux/usb.h:1619
  RIP: 0010:line6_start_listen+0x3fe/0x9e0 sound/usb/line6/driver.c:76
  Call Trace:
   <IRQ>
   line6_data_received+0x1f7/0x470 sound/usb/line6/driver.c:326
   __usb_hcd_giveback_urb+0x2e0/0x650 drivers/usb/core/hcd.c:1779
   usb_hcd_giveback_urb+0x337/0x420 drivers/usb/core/hcd.c:1845
   dummy_timer+0xba9/0x39f0 drivers/usb/gadget/udc/dummy_hcd.c:1965
   call_timer_fn+0x2a2/0x940 kernel/time/timer.c:1281
   ....

Since the whole clean-up procedure is done in line6_disconnect()
callback, we can simply call it in the error path instead of
open-coding the whole again.  It'll fix such an issue automagically.

The bug was spotted by syzkaller.

Fixes: eedd0e95d355 ("ALSA: line6: Don't forget to call driver's destructor at error path")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: caiaq: Fix stray URB at probe error path

commit 99fee508245825765ff60155fed43f970ff83a8f upstream.

caiaq driver doesn't kill the URB properly at its error path during
the probe, which may lead to a use-after-free error later.  This patch
addresses it.

Reported-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: seq: Fix copy_from_user() call inside lock

commit 5803b023881857db32ffefa0d269c90280a67ee0 upstream.

The event handler in the virmidi sequencer code takes a read-lock for
the linked list traverse, while it's calling snd_seq_dump_var_event()
in the loop.  The latter function may expand the user-space data
depending on the event type.  It eventually invokes copy_from_user(),
which might be a potential dead-lock.

The sequencer core guarantees that the user-space data is passed only
with atomic=0 argument, but snd_virmidi_dev_receive_event() ignores it
and always takes read-lock().  For avoiding the problem above, this
patch introduces rwsem for non-atomic case, while keeping rwlock for
atomic case.

Also while we're at it: the superfluous irq flags is dropped in
snd_virmidi_input_open().

Reported-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: seq: Fix use-after-free at creating a port

commit 71105998845fb012937332fe2e806d443c09e026 upstream.

There is a potential race window opened at creating and deleting a
port via ioctl, as spotted by fuzzing.  snd_seq_create_port() creates
a port object and returns its pointer, but it doesn't take the
refcount, thus it can be deleted immediately by another thread.
Meanwhile, snd_seq_ioctl_create_port() still calls the function
snd_seq_system_client_ev_port_start() with the created port object
that is being deleted, and this triggers use-after-free like:

 BUG: KASAN: use-after-free in snd_seq_ioctl_create_port+0x504/0x630 [snd_seq] at addr ffff8801f2241cb1
 =============================================================================
 BUG kmalloc-512 (Tainted: G    B          ): kasan: bad access detected
 -----------------------------------------------------------------------------
 INFO: Allocated in snd_seq_create_port+0x94/0x9b0 [snd_seq] age=1 cpu=3 pid=4511
  ___slab_alloc+0x425/0x460
  __slab_alloc+0x20/0x40
   kmem_cache_alloc_trace+0x150/0x190
snd_seq_create_port+0x94/0x9b0 [snd_seq]
snd_seq_ioctl_create_port+0xd1/0x630 [snd_seq]
  snd_seq_do_ioctl+0x11c/0x190 [snd_seq]
  snd_seq_ioctl+0x40/0x80 [snd_seq]
  do_vfs_ioctl+0x54b/0xda0
  SyS_ioctl+0x79/0x90
  entry_SYSCALL_64_fastpath+0x16/0x75
 INFO: Freed in port_delete+0x136/0x1a0 [snd_seq] age=1 cpu=2 pid=4717
  __slab_free+0x204/0x310
  kfree+0x15f/0x180
  port_delete+0x136/0x1a0 [snd_seq]
  snd_seq_delete_port+0x235/0x350 [snd_seq]
  snd_seq_ioctl_delete_port+0xc8/0x180 [snd_seq]
  snd_seq_do_ioctl+0x11c/0x190 [snd_seq]
  snd_seq_ioctl+0x40/0x80 [snd_seq]
  do_vfs_ioctl+0x54b/0xda0
  SyS_ioctl+0x79/0x90
  entry_SYSCALL_64_fastpath+0x16/0x75
 Call Trace:
  [<ffffffff81b03781>] dump_stack+0x63/0x82
  [<ffffffff81531b3b>] print_trailer+0xfb/0x160
  [<ffffffff81536db4>] object_err+0x34/0x40
  [<ffffffff815392d3>] kasan_report.part.2+0x223/0x520
  [<ffffffffa07aadf4>] ? snd_seq_ioctl_create_port+0x504/0x630 [snd_seq]
  [<ffffffff815395fe>] __asan_report_load1_noabort+0x2e/0x30
  [<ffffffffa07aadf4>] snd_seq_ioctl_create_port+0x504/0x630 [snd_seq]
  [<ffffffffa07aa8f0>] ? snd_seq_ioctl_delete_port+0x180/0x180 [snd_seq]
  [<ffffffff8136be50>] ? taskstats_exit+0xbc0/0xbc0
  [<ffffffffa07abc5c>] snd_seq_do_ioctl+0x11c/0x190 [snd_seq]
  [<ffffffffa07abd10>] snd_seq_ioctl+0x40/0x80 [snd_seq]
  [<ffffffff8136d433>] ? acct_account_cputime+0x63/0x80
  [<ffffffff815b515b>] do_vfs_ioctl+0x54b/0xda0
  .....

We may fix this in a few different ways, and in this patch, it's fixed
simply by taking the refcount properly at snd_seq_create_port() and
letting the caller unref the object after use.  Also, there is another
potential use-after-free by sprintf() call in snd_seq_create_port(),
and this is moved inside the lock.

This fix covers CVE-2017-15265.

Reported-and-tested-by: Michael23 Yu <ycqzsy@gmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: usb-audio: Kill stray URB at exiting

commit 124751d5e63c823092060074bd0abaae61aaa9c4 upstream.

USB-audio driver may leave a stray URB for the mixer interrupt when it
exits by some error during probe.  This leads to a use-after-free
error as spotted by syzkaller like:
  ==================================================================
  BUG: KASAN: use-after-free in snd_usb_mixer_interrupt+0x604/0x6f0
  Call Trace:
   <IRQ>
   __dump_stack lib/dump_stack.c:16
   dump_stack+0x292/0x395 lib/dump_stack.c:52
   print_address_description+0x78/0x280 mm/kasan/report.c:252
   kasan_report_error mm/kasan/report.c:351
   kasan_report+0x23d/0x350 mm/kasan/report.c:409
   __asan_report_load8_noabort+0x19/0x20 mm/kasan/report.c:430
   snd_usb_mixer_interrupt+0x604/0x6f0 sound/usb/mixer.c:2490
   __usb_hcd_giveback_urb+0x2e0/0x650 drivers/usb/core/hcd.c:1779
   ....

  Allocated by task 1484:
   save_stack_trace+0x1b/0x20 arch/x86/kernel/stacktrace.c:59
   save_stack+0x43/0xd0 mm/kasan/kasan.c:447
   set_track mm/kasan/kasan.c:459
   kasan_kmalloc+0xad/0xe0 mm/kasan/kasan.c:551
   kmem_cache_alloc_trace+0x11e/0x2d0 mm/slub.c:2772
   kmalloc ./include/linux/slab.h:493
   kzalloc ./include/linux/slab.h:666
   snd_usb_create_mixer+0x145/0x1010 sound/usb/mixer.c:2540
   create_standard_mixer_quirk+0x58/0x80 sound/usb/quirks.c:516
   snd_usb_create_quirk+0x92/0x100 sound/usb/quirks.c:560
   create_composite_quirk+0x1c4/0x3e0 sound/usb/quirks.c:59
   snd_usb_create_quirk+0x92/0x100 sound/usb/quirks.c:560
   usb_audio_probe+0x1040/0x2c10 sound/usb/card.c:618
   ....

  Freed by task 1484:
   save_stack_trace+0x1b/0x20 arch/x86/kernel/stacktrace.c:59
   save_stack+0x43/0xd0 mm/kasan/kasan.c:447
   set_track mm/kasan/kasan.c:459
   kasan_slab_free+0x72/0xc0 mm/kasan/kasan.c:524
   slab_free_hook mm/slub.c:1390
   slab_free_freelist_hook mm/slub.c:1412
   slab_free mm/slub.c:2988
   kfree+0xf6/0x2f0 mm/slub.c:3919
   snd_usb_mixer_free+0x11a/0x160 sound/usb/mixer.c:2244
   snd_usb_mixer_dev_free+0x36/0x50 sound/usb/mixer.c:2250
   __snd_device_free+0x1ff/0x380 sound/core/device.c:91
   snd_device_free_all+0x8f/0xe0 sound/core/device.c:244
   snd_card_do_free sound/core/init.c:461
   release_card_device+0x47/0x170 sound/core/init.c:181
   device_release+0x13f/0x210 drivers/base/core.c:814
   ....

Actually such a URB is killed properly at disconnection when the
device gets probed successfully, and what we need is to apply it for
the error-path, too.

In this patch, we apply snd_usb_mixer_disconnect() at releasing.
Also introduce a new flag, disconnected, to struct usb_mixer_interface
for not performing the disconnection procedure twice.

Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iommu/amd: Finish TLB flush in amd_iommu_unmap()

commit ce76353f169a6471542d999baf3d29b121dce9c0 upstream.

The function only sends the flush command to the IOMMU(s),
but does not wait for its completion when it returns. Fix
that.

Fixes: 601367d76bd1 ('x86/amd-iommu: Remove iommu_flush_domain function')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: renesas_usbhs: Fix DMAC sequence for receiving zero-length packet

commit 29c7f3e68eec4ae94d85ad7b5dfdafdb8089f513 upstream.

The DREQE bit of the DnFIFOSEL should be set to 1 after the DE bit of
USB-DMAC on R-Car SoCs is set to 1 after the USB-DMAC received a
zero-length packet. Otherwise, a transfer completion interruption
of USB-DMAC doesn't happen. Even if the driver changes the sequence,
normal operations (transmit/receive without zero-length packet) will
not cause any side-effects. So, this patch fixes the sequence anyway.

Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[shimoda: revise the commit log]
Fixes: e73a9891b3a1 ("usb: renesas_usbhs: add DMAEngine support")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: nVMX: fix guest CR4 loading when emulating L2 to L1 exit

commit 8eb3f87d903168bdbd1222776a6b1e281f50513e upstream.

When KVM emulates an exit from L2 to L1, it loads L1 CR4 into the
guest CR4. Before this CR4 loading, the guest CR4 refers to L2
CR4. Because these two CR4's are in different levels of guest, we
should vmx_set_cr4() rather than kvm_set_cr4() here. The latter, which
is used to handle guest writes to its CR4, checks the guest change to
CR4 and may fail if the change is invalid.

The failure may cause trouble. Consider we start
  a L1 guest with non-zero L1 PCID in use,
     (i.e. L1 CR4.PCIDE == 1 && L1 CR3.PCID != 0)
and
  a L2 guest with L2 PCID disabled,
     (i.e. L2 CR4.PCIDE == 0)
and following events may happen:

1. If kvm_set_cr4() is used in load_vmcs12_host_state() to load L1 CR4
   into guest CR4 (in VMCS01) for L2 to L1 exit, it will fail because
   of PCID check. As a result, the guest CR4 recorded in L0 KVM (i.e.
   vcpu->arch.cr4) is left to the value of L2 CR4.

2. Later, if L1 attempts to change its CR4, e.g., clearing VMXE bit,
   kvm_set_cr4() in L0 KVM will think L1 also wants to enable PCID,
   because the wrong L2 CR4 is used by L0 KVM as L1 CR4. As L1
   CR3.PCID != 0, L0 KVM will inject GP to L1 guest.

Fixes: 4704d0befb072 ("KVM: nVMX: Exiting from L2 to L1")
Cc: qemu-stable@nongnu.org
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: shash - Fix zero-length shash ahash digest crash

commit b61907bb42409adf9b3120f741af7c57dd7e3db2 upstream.

The shash ahash digest adaptor function may crash if given a
zero-length input together with a null SG list.  This is because
it tries to read the SG list before looking at the length.

This patch fixes it by checking the length first.

Reported-by: Stephan Müller<smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Stephan Müller <smueller@chronox.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: usbhid: fix out-of-bounds bug

commit f043bfc98c193c284e2cd768fefabe18ac2fed9b upstream.

The hid descriptor identifies the length and type of subordinate
descriptors for a device. If the received hid descriptor is smaller than
the size of the struct hid_descriptor, it is possible to cause
out-of-bounds.

In addition, if bNumDescriptors of the hid descriptor have an incorrect
value, this can also cause out-of-bounds while approaching hdesc->desc[n].

So check the size of hid descriptor and bNumDescriptors.

BUG: KASAN: slab-out-of-bounds in usbhid_parse+0x9b1/0xa20
Read of size 1 at addr ffff88006c5f8edf by task kworker/1:2/1261

CPU: 1 PID: 1261 Comm: kworker/1:2 Not tainted
4.14.0-rc1-42251-gebb2c2437d80 #169
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:16
dump_stack+0x292/0x395 lib/dump_stack.c:52
print_address_description+0x78/0x280 mm/kasan/report.c:252
kasan_report_error mm/kasan/report.c:351
kasan_report+0x22f/0x340 mm/kasan/report.c:409
__asan_report_load1_noabort+0x19/0x20 mm/kasan/report.c:427
usbhid_parse+0x9b1/0xa20 drivers/hid/usbhid/hid-core.c:1004
hid_add_device+0x16b/0xb30 drivers/hid/hid-core.c:2944
usbhid_probe+0xc28/0x1100 drivers/hid/usbhid/hid-core.c:1369
usb_probe_interface+0x35d/0x8e0 drivers/usb/core/driver.c:361
really_probe drivers/base/dd.c:413
driver_probe_device+0x610/0xa00 drivers/base/dd.c:557
__device_attach_driver+0x230/0x290 drivers/base/dd.c:653
bus_for_each_drv+0x161/0x210 drivers/base/bus.c:463
__device_attach+0x26e/0x3d0 drivers/base/dd.c:710
device_initial_probe+0x1f/0x30 drivers/base/dd.c:757
bus_probe_device+0x1eb/0x290 drivers/base/bus.c:523
device_add+0xd0b/0x1660 drivers/base/core.c:1835
usb_set_configuration+0x104e/0x1870 drivers/usb/core/message.c:1932
generic_probe+0x73/0xe0 drivers/usb/core/generic.c:174
usb_probe_device+0xaf/0xe0 drivers/usb/core/driver.c:266
really_probe drivers/base/dd.c:413
driver_probe_device+0x610/0xa00 drivers/base/dd.c:557
__device_attach_driver+0x230/0x290 drivers/base/dd.c:653
bus_for_each_drv+0x161/0x210 drivers/base/bus.c:463
__device_attach+0x26e/0x3d0 drivers/base/dd.c:710
device_initial_probe+0x1f/0x30 drivers/base/dd.c:757
bus_probe_device+0x1eb/0x290 drivers/base/bus.c:523
device_add+0xd0b/0x1660 drivers/base/core.c:1835
usb_new_device+0x7b8/0x1020 drivers/usb/core/hub.c:2457
hub_port_connect drivers/usb/core/hub.c:4903
hub_port_connect_change drivers/usb/core/hub.c:5009
port_event drivers/usb/core/hub.c:5115
hub_event+0x194d/0x3740 drivers/usb/core/hub.c:5195
process_one_work+0xc7f/0x1db0 kernel/workqueue.c:2119
worker_thread+0x221/0x1850 kernel/workqueue.c:2253
kthread+0x3a1/0x470 kernel/kthread.c:231
ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:431

Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dmaengine: edma: Align the memcpy acnt array size with the transfer

commit 87a2f622cc6446c7d09ac655b7b9b04886f16a4c upstream.

Memory to Memory transfers does not have any special alignment needs
regarding to acnt array size, but if one of the areas are in memory mapped
regions (like PCIe memory), we need to make sure that the acnt array size
is aligned with the mem copy parameters.

Before "dmaengine: edma: Optimize memcpy operation" change the memcpy was set
up in a different way: acnt == number of bytes in a word based on
__ffs((src | dest | len), bcnt and ccnt for looping the necessary number of
words to comlete the trasnfer.

Instead of reverting the commit we can fix it to make sure that the ACNT size
is aligned to the traswnfer.

Fixes: df6694f80365a (dmaengine: edma: Optimize memcpy operation)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: math-emu: Remove pr_err() calls from fpu_emu()

commit ca8eb05b5f332a9e1ab3e2ece498d49f4d683470 upstream.

The FPU emulator includes 2 calls to pr_err() which are triggered by
invalid instruction encodings for MIPSr6 cmp.cond.fmt instructions.
These cases are not kernel errors, merely invalid instructions which are
already handled by delivering a SIGILL which will provide notification
that something failed in cases where that makes sense.

In cases where that SIGILL is somewhat expected & being handled, for
example when crashme happens to generate one of the affected bad
encodings, the message is printed with no useful context about what
triggered it & spams the kernel log for no good reason.

Remove the pr_err() calls to make crashme run silently & treat the bad
encodings the same way we do others, with a SIGILL & no further kernel
log output.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: f8c3c6717a71 ("MIPS: math-emu: Add support for the CMP.condn.fmt R6 instruction")
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17253/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: dummy-hcd: Fix deadlock caused by disconnect detection

commit ab219221a5064abfff9f78c323c4a257b16cdb81 upstream.

The dummy-hcd driver calls the gadget driver's disconnect callback
under the wrong conditions.  It should invoke the callback when Vbus
power is turned off, but instead it does so when the D+ pullup is
turned off.

This can cause a deadlock in the composite core when a gadget driver
is unregistered:

[   88.361471] ============================================
[   88.362014] WARNING: possible recursive locking detected
[   88.362580] 4.14.0-rc2+ #9 Not tainted
[   88.363010] --------------------------------------------
[   88.363561] v4l_id/526 is trying to acquire lock:
[   88.364062]  (&(&cdev->lock)->rlock){....}, at: [<ffffffffa0547e03>] composite_disconnect+0x43/0x100 [libcomposite]
[   88.365051]
[   88.365051] but task is already holding lock:
[   88.365826]  (&(&cdev->lock)->rlock){....}, at: [<ffffffffa0547b09>] usb_function_deactivate+0x29/0x80 [libcomposite]
[   88.366858]
[   88.366858] other info that might help us debug this:
[   88.368301]  Possible unsafe locking scenario:
[   88.368301]
[   88.369304]        CPU0
[   88.369701]        ----
[   88.370101]   lock(&(&cdev->lock)->rlock);
[   88.370623]   lock(&(&cdev->lock)->rlock);
[   88.371145]
[   88.371145]  *** DEADLOCK ***
[   88.371145]
[   88.372211]  May be due to missing lock nesting notation
[   88.372211]
[   88.373191] 2 locks held by v4l_id/526:
[   88.373715]  #0:  (&(&cdev->lock)->rlock){....}, at: [<ffffffffa0547b09>] usb_function_deactivate+0x29/0x80 [libcomposite]
[   88.374814]  #1:  (&(&dum_hcd->dum->lock)->rlock){....}, at: [<ffffffffa05bd48d>] dummy_pullup+0x7d/0xf0 [dummy_hcd]
[   88.376289]
[   88.376289] stack backtrace:
[   88.377726] CPU: 0 PID: 526 Comm: v4l_id Not tainted 4.14.0-rc2+ #9
[   88.378557] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
[   88.379504] Call Trace:
[   88.380019]  dump_stack+0x86/0xc7
[   88.380605]  __lock_acquire+0x841/0x1120
[   88.381252]  lock_acquire+0xd5/0x1c0
[   88.381865]  ? composite_disconnect+0x43/0x100 [libcomposite]
[   88.382668]  _raw_spin_lock_irqsave+0x40/0x54
[   88.383357]  ? composite_disconnect+0x43/0x100 [libcomposite]
[   88.384290]  composite_disconnect+0x43/0x100 [libcomposite]
[   88.385490]  set_link_state+0x2d4/0x3c0 [dummy_hcd]
[   88.386436]  dummy_pullup+0xa7/0xf0 [dummy_hcd]
[   88.387195]  usb_gadget_disconnect+0xd8/0x160 [udc_core]
[   88.387990]  usb_gadget_deactivate+0xd3/0x160 [udc_core]
[   88.388793]  usb_function_deactivate+0x64/0x80 [libcomposite]
[   88.389628]  uvc_function_disconnect+0x1e/0x40 [usb_f_uvc]

This patch changes the code to test the port-power status bit rather
than the port-connect status bit when deciding whether to isue the
callback.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: David Tulloh <david@tulloh.id.au>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rcu: Allow for page faults in NMI handlers

commit 28585a832602747cbfa88ad8934013177a3aae38 upstream.

A number of architecture invoke rcu_irq_enter() on exception entry in
order to allow RCU read-side critical sections in the exception handler
when the exception is from an idle or nohz_full CPU.  This works, at
least unless the exception happens in an NMI handler.  In that case,
rcu_nmi_enter() would already have exited the extended quiescent state,
which would mean that rcu_irq_enter() would (incorrectly) cause RCU
to think that it is again in an extended quiescent state.  This will
in turn result in lockdep splats in response to later RCU read-side
critical sections.

This commit therefore causes rcu_irq_enter() and rcu_irq_exit() to
take no action if there is an rcu_nmi_enter() in effect, thus avoiding
the unscheduled return to RCU quiescent state.  This in turn should
make the kernel safe for on-demand RCU voyeurism.

Link: http://lkml.kernel.org/r/20170922211022.GA18084@linux.vnet.ibm.com
Cc: stable@vger.kernel.org
Fixes: 0be964be0 ("module: Sanitize RCU usage and locking")
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: use IWL_HCMD_NOCOPY for MCAST_FILTER_CMD

commit 97bce57bd7f96e1218751996f549a6e61f18cc8c upstream.

The MCAST_FILTER_CMD can get quite large when we have many mcast
addresses to set (we support up to 255).  So the command should be
send as NOCOPY to prevent a warning caused by too-long commands:

WARNING: CPU: 0 PID: 9700 at /root/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/pcie/tx.c:1550 iwl_pcie_enqueue_hcmd+0x8c7/0xb40 [iwlwifi]
Command MCAST_FILTER_CMD (0x1d0) is too large (328 bytes)

This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=196743

Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nl80211: Define policy for packet pattern attributes

commit ad670233c9e1d5feb365d870e30083ef1b889177 upstream.

Define a policy for packet pattern attributes in order to fix a
potential read over the end of the buffer during nla_get_u32()
of the NL80211_PKTPAT_OFFSET attribute.

Note that the data there can always be read due to SKB allocation
(with alignment and struct skb_shared_info at the end), but the
data might be uninitialized. This could be used to leak some data
from uninitialized vmalloc() memory, but most drivers don't allow
an offset (so you'd just get -EINVAL if the data is non-zero) or
just allow it with a fixed value - 100 or 128 bytes, so anything
above that would get -EINVAL. With brcmfmac the limit is 1500 so
(at least) one byte could be obtained.

Cc: stable@kernel.org
Signed-off-by: Peng Xu <pxu@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[rewrite description based on SKB allocation knowledge]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

CIFS: Reconnect expired SMB sessions

commit 511c54a2f69195b28afb9dd119f03787b1625bb4 upstream.

According to the MS-SMB2 spec (3.2.5.1.6) once the client receives
STATUS_NETWORK_SESSION_EXPIRED error code from a server it should
reconnect the current SMB session. Currently the client doesn't do
that. This can result in subsequent client requests failing by
the server. The patch adds an additional logic to the demultiplex
thread to identify expired sessions and reconnect them.

Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: in ext4_seek_{hole,data}, return -ENXIO for negative offsets

commit 1bd8d6cd3e413d64e543ec3e69ff43e75a1cf1ea upstream.

In the ext4 implementations of SEEK_HOLE and SEEK_DATA, make sure we
return -ENXIO for negative offsets instead of banging around inside
the extent code and returning -EFSCORRUPTED.

Reported-by: Mateusz S <muttdini@gmail.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

brcmfmac: add length check in brcmf_cfg80211_escan_handler()

commit 17df6453d4be17910456e99c5a85025aa1b7a246 upstream.

Upon handling the firmware notification for scans the length was
checked properly and may result in corrupting kernel heap memory
due to buffer overruns. This fix addresses CVE-2017-0786.

Cc: Kevin Cernekee <cernekee@chromium.org>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.4.92

ext4: don't allow encrypted operations without keys

commit 173b8439e1ba362007315868928bf9d26e5cc5a6 upstream.

While we allow deletes without the key, the following should not be
permitted:

# cd /vdc/encrypted-dir-without-key
# ls -l
total 4
-rw-r--r-- 1 root root   0 Dec 27 22:35 6,LKNRJsp209FbXoSvJWzB
-rw-r--r-- 1 root root 286 Dec 27 22:35 uRJ5vJh9gE7vcomYMqTAyD
# mv uRJ5vJh9gE7vcomYMqTAyD  6,LKNRJsp209FbXoSvJWzB

Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: Don't clear SGID when inheriting ACLs

commit a3bb2d5587521eea6dab2d05326abb0afb460abd upstream.

When new directory 'DIR1' is created in a directory 'DIR0' with SGID bit
set, DIR1 is expected to have SGID bit set (and owning group equal to
the owning group of 'DIR0'). However when 'DIR0' also has some default
ACLs that 'DIR1' inherits, setting these ACLs will result in SGID bit on
'DIR1' to get cleared if user is not member of the owning group.

Fix the problem by moving posix_acl_update_mode() out of
__ext4_set_acl() into ext4_set_acl(). That way the function will not be
called when inheriting ACLs which is what we want as it prevents SGID
bit clearing and the mode has been properly set by posix_acl_create()
anyway.

Fixes: 073931017b49d9458aa351605b43a7e34598caef
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: fix data corruption for mmap writes

commit a056bdaae7a181f7dcc876cfab2f94538e508709 upstream.

mpage_submit_page() can race with another process growing i_size and
writing data via mmap to the written-back page. As mpage_submit_page()
samples i_size too early, it may happen that ext4_bio_write_page()
zeroes out too large tail of the page and thus corrupts user data.

Fix the problem by sampling i_size only after the page has been
write-protected in page tables by clear_page_dirty_for_io() call.

Reported-by: Michael Zimmer <michael@swarm64.com>
CC: stable@vger.kernel.org
Fixes: cb20d5188366f04d96d2e07b1240cc92170ade40
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sched/cpuset/pm: Fix cpuset vs. suspend-resume bugs

commit 50e76632339d4655859523a39249dd95ee5e93e7 upstream.

Cpusets vs. suspend-resume is _completely_ broken. And it got noticed
because it now resulted in non-cpuset usage breaking too.

On suspend cpuset_cpu_inactive() doesn't call into
cpuset_update_active_cpus() because it doesn't want to move tasks about,
there is no need, all tasks are frozen and won't run again until after
we've resumed everything.

But this means that when we finally do call into
cpuset_update_active_cpus() after resuming the last frozen cpu in
cpuset_cpu_active(), the top_cpuset will not have any difference with
the cpu_active_mask and this it will not in fact do _anything_.

So the cpuset configuration will not be restored. This was largely
hidden because we would unconditionally create identity domains and
mobile users would not in fact use cpusets much. And servers what do use
cpusets tend to not suspend-resume much.

An addition problem is that we'd not in fact wait for the cpuset work to
finish before resuming the tasks, allowing spurious migrations outside
of the specified domains.

Fix the rebuild by introducing cpuset_force_rebuild() and fix the
ordering with cpuset_wait_for_hotplug().

Reported-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: deb7aa308ea2 ("cpuset: reorganize CPU / memory hotplug handling")
Link: http://lkml.kernel.org/r/20170907091338.orwxrqkbfkki3c24@hirez.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvme: protect against simultaneous shutdown invocations

commit 77bf25ea70200cddf083f74b7f617e5f07fac8bd upstream.

[Back-ported to 4.4. The difference is the file location of the struct
definition that's adding the mutex.

This fixes reported kernel panics in 4.4-stable from simultaneous
controller resets that was never supposed to be allowed to happen.]

Signed-off-by: Keith Busch <keith.busch@intel.com>
[hch: split from a larger patch]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915/bios: ignore HDMI on port A

commit 2ba7d7e0437127314864238f8bfcb8369d81075c upstream.

The hardware state readout oopses after several warnings when trying to
use HDMI on port A, if such a combination is configured in VBT. Filter
the combo out already at the VBT parsing phase.

v2: also ignore DVI (Ville)

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102889
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Daniel Drake <dan@reactivated.net>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170921141920.18172-1-jani.nikula@intel.com
(cherry picked from commit d27ffc1d00327c29b3aa97f941b42f0949f9e99f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

brcmfmac: setup passive scan if requested by user-space

commit 35f62727df0ed8e5e4857e162d94fd46d861f1cf upstream.

The driver was not properly configuring firmware with regard to the
type of scan. It always performed an active scan even when user-space
was requesting for passive scan, ie. the scan request was done without
any SSIDs specified.

Reported-by: Huang, Jiangyang <Jiangyang.Huang@itron.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

uwb: ensure that endpoint is interrupt

commit 70e743e4cec3733dc13559f6184b35d358b9ef3f upstream.

hwarc_neep_init() assumes that endpoint 0 is interrupt, but there's no
check for that, which results in a WARNING in USB core code, when a bad
USB descriptor is provided from a device:

usb 1-1: BOGUS urb xfer, pipe 1 != type 3
------------[ cut here ]------------
WARNING: CPU: 0 PID: 3 at drivers/usb/core/urb.c:449 usb_submit_urb+0xf8a/0x11d0
Modules linked in:
CPU: 0 PID: 3 Comm: kworker/0:0 Not tainted 4.13.0+ #111
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
task: ffff88006bdc1a00 task.stack: ffff88006bde8000
RIP: 0010:usb_submit_urb+0xf8a/0x11d0 drivers/usb/core/urb.c:448
RSP: 0018:ffff88006bdee3c0 EFLAGS: 00010282
RAX: 0000000000000029 RBX: ffff8800672a7200 RCX: 0000000000000000
RDX: 0000000000000029 RSI: ffff88006c815c78 RDI: ffffed000d7bdc6a
RBP: ffff88006bdee4c0 R08: fffffbfff0fe00ff R09: fffffbfff0fe00ff
R10: 0000000000000018 R11: fffffbfff0fe00fe R12: 1ffff1000d7bdc7f
R13: 0000000000000003 R14: 0000000000000001 R15: ffff88006b02cc90
FS:  0000000000000000(0000) GS:ffff88006c800000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fe4daddf000 CR3: 000000006add6000 CR4: 00000000000006f0
Call Trace:
 hwarc_neep_init+0x4ce/0x9c0 drivers/uwb/hwa-rc.c:710
 uwb_rc_add+0x2fb/0x730 drivers/uwb/lc-rc.c:361
 hwarc_probe+0x34e/0x9b0 drivers/uwb/hwa-rc.c:858
 usb_probe_interface+0x351/0x8d0 drivers/usb/core/driver.c:361
 really_probe drivers/base/dd.c:385
 driver_probe_device+0x610/0xa00 drivers/base/dd.c:529
 __device_attach_driver+0x230/0x290 drivers/base/dd.c:625
 bus_for_each_drv+0x15e/0x210 drivers/base/bus.c:463
 __device_attach+0x269/0x3c0 drivers/base/dd.c:682
 device_initial_probe+0x1f/0x30 drivers/base/dd.c:729
 bus_probe_device+0x1da/0x280 drivers/base/bus.c:523
 device_add+0xcf9/0x1640 drivers/base/core.c:1703
 usb_set_configuration+0x1064/0x1890 drivers/usb/core/message.c:1932
 generic_probe+0x73/0xe0 drivers/usb/core/generic.c:174
 usb_probe_device+0xaf/0xe0 drivers/usb/core/driver.c:266
 really_probe drivers/base/dd.c:385
 driver_probe_device+0x610/0xa00 drivers/base/dd.c:529
 __device_attach_driver+0x230/0x290 drivers/base/dd.c:625
 bus_for_each_drv+0x15e/0x210 drivers/base/bus.c:463
 __device_attach+0x269/0x3c0 drivers/base/dd.c:682
 device_initial_probe+0x1f/0x30 drivers/base/dd.c:729
 bus_probe_device+0x1da/0x280 drivers/base/bus.c:523
 device_add+0xcf9/0x1640 drivers/base/core.c:1703
 usb_new_device+0x7b8/0x1020 drivers/usb/core/hub.c:2457
 hub_port_connect drivers/usb/core/hub.c:4890
 hub_port_connect_change drivers/usb/core/hub.c:4996
 port_event drivers/usb/core/hub.c:5102
 hub_event+0x23c8/0x37c0 drivers/usb/core/hub.c:5182
 process_one_work+0x9fb/0x1570 kernel/workqueue.c:2097
 worker_thread+0x1e4/0x1350 kernel/workqueue.c:2231
 kthread+0x324/0x3f0 kernel/kthread.c:231
 ret_from_fork+0x25/0x30 arch/x86/entry/entry_64.S:425
Code: 48 8b 85 30 ff ff ff 48 8d b8 98 00 00 00 e8 8e 93 07 ff 45 89
e8 44 89 f1 4c 89 fa 48 89 c6 48 c7 c7 a0 e5 55 86 e8 20 08 8f fd <0f>
ff e9 9b f7 ff ff e8 4a 04 d6 fd e9 80 f7 ff ff e8 60 11 a6
---[ end trace 55d741234124cfc3 ]---

Check that endpoint is interrupt.

Found by syzkaller.

Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

uwb: properly check kthread_run return value

commit bbf26183b7a6236ba602f4d6a2f7cade35bba043 upstream.

uwbd_start() calls kthread_run() and checks that the return value is
not NULL. But the return value is not NULL in case kthread_run() fails,
it takes the form of ERR_PTR(-EINTR).

Use IS_ERR() instead.

Also add a check to uwbd_stop().

Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adc: mcp320x: Fix oops on module unload

commit 0964e40947a630a2a6f724e968246992f97bcf1c upstream.

The driver calls spi_get_drvdata() in its ->remove hook even though it
has never called spi_set_drvdata().  Stack trace for posterity:

Unable to handle kernel NULL pointer dereference at virtual address 00000220
Internal error: Oops: 5 [#1] SMP ARM
[<8072f564>] (mutex_lock) from [<7f1400d0>] (iio_device_unregister+0x24/0x7c [industrialio])
[<7f1400d0>] (iio_device_unregister [industrialio]) from [<7f15e020>] (mcp320x_remove+0x20/0x30 [mcp320x])
[<7f15e020>] (mcp320x_remove [mcp320x]) from [<8055a8cc>] (spi_drv_remove+0x2c/0x44)
[<8055a8cc>] (spi_drv_remove) from [<805087bc>] (__device_release_driver+0x98/0x134)
[<805087bc>] (__device_release_driver) from [<80509180>] (driver_detach+0xdc/0xe0)
[<80509180>] (driver_detach) from [<8050823c>] (bus_remove_driver+0x5c/0xb0)
[<8050823c>] (bus_remove_driver) from [<80509ab0>] (driver_unregister+0x38/0x58)
[<80509ab0>] (driver_unregister) from [<7f15e69c>] (mcp320x_driver_exit+0x14/0x1c [mcp320x])
[<7f15e69c>] (mcp320x_driver_exit [mcp320x]) from [<801a78d0>] (SyS_delete_module+0x184/0x1d0)
[<801a78d0>] (SyS_delete_module) from [<80108100>] (ret_fast_syscall+0x0/0x1c)

Fixes: f5ce4a7a9291 ("iio: adc: add driver for MCP3204/08 12-bit ADC")
Cc: Oskar Andero <oskar.andero@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adc: mcp320x: Fix readout of negative voltages

commit e6f4794371ee7cce1339e7ca9542f1e703c5f84a upstream.

Commit f686a36b4b79 ("iio: adc: mcp320x: Add support for mcp3301")
returns a signed voltage from mcp320x_adc_conversion() but neglects that
the caller interprets a negative return value as failure.  Only mcp3301
(and the upcoming mcp3550/1/3) is affected as the other chips are
incapable of measuring negative voltages.

Fix and while at it, add mcp3301 to the list of supported chips at the
top of the file.

Fixes: f686a36b4b79 ("iio: adc: mcp320x: Add support for mcp3301")
Cc: Andrea Galbusera <gizero@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>