xhci: Fix false warning message about wrong bounce buffer write length

commit c03101ff4f74bb30679c1a03d551ecbef1024bf6 upstream.

The check printing out the "WARN Wrong bounce buffer write length:"
uses incorrect values when comparing bytes written from scatterlist
to bounce buffer. Actual copied lengths are fine.

The used seg->bounce_len will be set to equal new_buf_len a few lines later
in the code, but is incorrect when doing the comparison.

The patch which added this false warning was backported to 4.8+ kernels
so this should be backported as far as well.

Cc: <stable@vger.kernel.org> # v4.8+
Fixes: 597c56e372da ("xhci: update bounce buffer with correct sg num")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-2-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb-skeleton: fix NULL-deref on disconnect

commit bed5ef230943863b9abf5eae226a20fad9a8ff71 upstream.

The driver was using its struct usb_interface pointer as an inverted
disconnected flag and was setting it to NULL before making sure all
completion handlers had run. This could lead to NULL-pointer
dereferences in the dev_err() statements in the completion handlers
which relies on said pointer.

Fix this by using a dedicated disconnected flag.

Note that this is also addresses a NULL-pointer dereference at release()
and a struct usb_interface reference leak introduced by a recent runtime
PM fix, which depends on and should have been submitted together with
this patch.

Fixes: 4212cd74ca6f ("USB: usb-skeleton.c: remove err() usage")
Fixes: 5c290a5e42c3 ("USB: usb-skeleton: fix runtime PM after driver unbind")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191009170944.30057-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb-skeleton: fix runtime PM after driver unbind

commit 5c290a5e42c3387e82de86965784d30e6c5270fd upstream.

Since commit c2b71462d294 ("USB: core: Fix bug caused by duplicate
interface PM usage counter") USB drivers must always balance their
runtime PM gets and puts, including when the driver has already been
unbound from the interface.

Leaving the interface with a positive PM usage counter would prevent a
later bound driver from suspending the device.

Fixes: c2b71462d294 ("USB: core: Fix bug caused by duplicate interface PM usage counter")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191001084908.2003-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: yurex: fix NULL-derefs on disconnect

commit aafb00a977cf7d81821f7c9d12e04c558c22dc3c upstream.

The driver was using its struct usb_interface pointer as an inverted
disconnected flag, but was setting it to NULL without making sure all
code paths that used it were done with it.

Before commit ef61eb43ada6 ("USB: yurex: Fix protection fault after
device removal") this included the interrupt-in completion handler, but
there are further accesses in dev_err and dev_dbg statements in
yurex_write() and the driver-data destructor (sic!).

Fix this by unconditionally stopping also the control URB at disconnect
and by using a dedicated disconnected flag.

Note that we need to take a reference to the struct usb_interface to
avoid a use-after-free in the destructor whenever the device was
disconnected while the character device was still open.

Fixes: aadd6472d904 ("USB: yurex.c: remove dbg() usage")
Fixes: 45714104b9e8 ("USB: yurex.c: remove err() usage")
Cc: stable <stable@vger.kernel.org> # 3.5: ef61eb43ada6
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191009153848.8664-6-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: yurex: Don't retry on unexpected errors

commit 32a0721c6620b77504916dac0cea8ad497c4878a upstream.

According to Greg KH, it has been generally agreed that when a USB
driver encounters an unknown error (or one it can't handle directly),
it should just give up instead of going into a potentially infinite
retry loop.

The three codes -EPROTO, -EILSEQ, and -ETIME fall into this category.
They can be caused by bus errors such as packet loss or corruption,
attempting to communicate with a disconnected device, or by malicious
firmware.  Nowadays the extent of packet loss or corruption is
negligible, so it should be safe for a driver to give up whenever one
of these errors occurs.

Although the yurex driver handles -EILSEQ errors in this way, it
doesn't do the same for -EPROTO (as discovered by the syzbot fuzzer)
or other unrecognized errors.  This patch adjusts the driver so that
it doesn't log an error message for -EPROTO or -ETIME, and it doesn't
retry after any errors.

Reported-and-tested-by: syzbot+b24d736f18a1541ad550@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1909171245410.1590-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: rio500: Remove Rio 500 kernel driver

commit 015664d15270a112c2371d812f03f7c579b35a73 upstream.

The Rio500 kernel driver has not been used by Rio500 owners since 2001
not long after the rio500 project added support for a user-space USB stack
through the very first versions of usbdevfs and then libusb.

Support for the kernel driver was removed from the upstream utilities
in 2008:
https://gitlab.freedesktop.org/hadess/rio500/commit/943f624ab721eb8281c287650fcc9e2026f6f5db

Cc: Cesar Miquel <miquel@df.uba.ar>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/6251c17584d220472ce882a3d9c199c401a51a71.camel@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

panic: ensure preemption is disabled during panic()

commit 20bb759a66be52cf4a9ddd17fddaf509e11490cd upstream.

Calling 'panic()' on a kernel with CONFIG_PREEMPT=y can leave the
calling CPU in an infinite loop, but with interrupts and preemption
enabled.  From this state, userspace can continue to be scheduled,
despite the system being "dead" as far as the kernel is concerned.

This is easily reproducible on arm64 when booting with "nosmp" on the
command line; a couple of shell scripts print out a periodic "Ping"
message whilst another triggers a crash by writing to
/proc/sysrq-trigger:

  | sysrq: Trigger a crash
  | Kernel panic - not syncing: sysrq triggered crash
  | CPU: 0 PID: 1 Comm: init Not tainted 5.2.15 #1
  | Hardware name: linux,dummy-virt (DT)
  | Call trace:
  |  dump_backtrace+0x0/0x148
  |  show_stack+0x14/0x20
  |  dump_stack+0xa0/0xc4
  |  panic+0x140/0x32c
  |  sysrq_handle_reboot+0x0/0x20
  |  __handle_sysrq+0x124/0x190
  |  write_sysrq_trigger+0x64/0x88
  |  proc_reg_write+0x60/0xa8
  |  __vfs_write+0x18/0x40
  |  vfs_write+0xa4/0x1b8
  |  ksys_write+0x64/0xf0
  |  __arm64_sys_write+0x14/0x20
  |  el0_svc_common.constprop.0+0xb0/0x168
  |  el0_svc_handler+0x28/0x78
  |  el0_svc+0x8/0xc
  | Kernel Offset: disabled
  | CPU features: 0x0002,24002004
  | Memory Limit: none
  | ---[ end Kernel panic - not syncing: sysrq triggered crash ]---
  |  Ping 2!
  |  Ping 1!
  |  Ping 1!
  |  Ping 2!

The issue can also be triggered on x86 kernels if CONFIG_SMP=n,
otherwise local interrupts are disabled in 'smp_send_stop()'.

Disable preemption in 'panic()' before re-enabling interrupts.

Link: http://lkml.kernel.org/r/20191002123538.22609-1-will@kernel.org
Link: https://lore.kernel.org/r/BX1W47JXPMR8.58IYW53H6M5N@dragonstone
Signed-off-by: Will Deacon <will@kernel.org>
Reported-by: Xogium <contact@xogium.me>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: sgtl5000: Improve VAG power and mute control

[ Upstream commit b1f373a11d25fc9a5f7679c9b85799fe09b0dc4a ]

VAG power control is improved to fit the manual [1]. This patch fixes as
minimum one bug: if customer muxes Headphone to Line-In right after boot,
the VAG power remains off that leads to poor sound quality from line-in.

I.e. after boot:
  - Connect sound source to Line-In jack;
  - Connect headphone to HP jack;
  - Run following commands:
  $ amixer set 'Headphone' 80%
  $ amixer set 'Headphone Mux' LINE_IN

Change VAG power on/off control according to the following algorithm:
  - turn VAG power ON on the 1st incoming event.
  - keep it ON if there is any active VAG consumer (ADC/DAC/HP/Line-In).
  - turn VAG power OFF when there is the latest consumer's pre-down event
    come.
  - always delay after VAG power OFF to avoid pop.
  - delay after VAG power ON if the initiative consumer is Line-In, this
    prevents pop during line-in muxing.

According to the data sheet [1], to avoid any pops/clicks,
the outputs should be muted during input/output
routing changes.

[1] https://www.nxp.com/docs/en/data-sheet/SGTL5000.pdf

Cc: stable@vger.kernel.org
Fixes: 9b34e6cc3bc2 ("ASoC: Add Freescale SGTL5000 codec support")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20190719100524.23300-3-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nl80211: validate beacon head

commit f88eb7c0d002a67ef31aeb7850b42ff69abc46dc upstream.

We currently don't validate the beacon head, i.e. the header,
fixed part and elements that are to go in front of the TIM
element. This means that the variable elements there can be
malformed, e.g. have a length exceeding the buffer size, but
most downstream code from this assumes that this has already
been checked.

Add the necessary checks to the netlink policy.

Cc: stable@vger.kernel.org
Fixes: ed1b6cc7f80f ("cfg80211/nl80211: add beacon settings")
Link: https://lore.kernel.org/r/1569009255-I7ac7fbe9436e9d8733439eab8acbbd35e55c74ef@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cfg80211: Use const more consistently in for_each_element macros

commit 7388afe09143210f555bdd6c75035e9acc1fab96 upstream.

Enforce the first argument to be a correct type of a pointer to struct
element and avoid unnecessary typecasts from const to non-const pointers
(the change in validate_ie_attr() is needed to make this part work). In
addition, avoid signed/unsigned comparison within for_each_element() and
mark struct element packed just in case.

Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cfg80211: add and use strongly typed element iteration macros

commit 0f3b07f027f87a38ebe5c436490095df762819be upstream.

Rather than always iterating elements from frames with pure
u8 pointers, add a type "struct element" that encapsulates
the id/datalen/data format of them.

Then, add the element iteration macros
 * for_each_element
 * for_each_element_id
 * for_each_element_extid

which take, as their first 'argument', such a structure and
iterate through a given u8 array interpreting it as elements.

While at it and since we'll need it, also add
 * for_each_subelement
 * for_each_subelement_id
 * for_each_subelement_extid

which instead of taking data/length just take an outer element
and use its data/datalen.

Also add for_each_element_completed() to determine if any of
the loops above completed, i.e. it was able to parse all of
the elements successfully and no data remained.

Use for_each_element_id() in cfg80211_find_ie_match() as the
first user of this.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

coresight: etm4x: Use explicit barriers on enable/disable

commit 1004ce4c255fc3eb3ad9145ddd53547d1b7ce327 upstream.

Synchronization is recommended before disabling the trace registers
to prevent any start or stop points being speculative at the point
of disabling the unit (section 7.3.77 of ARM IHI 0064D).

Synchronization is also recommended after programming the trace
registers to ensure all updates are committed prior to normal code
resuming (section 4.3.7 of ARM IHI 0064D).

Let's ensure these syncronization points are present in the code
and clearly commented.

Note that we could rely on the barriers in CS_LOCK and
coresight_disclaim_device_unlocked or the context switch to user
space - however coresight may be of use in the kernel.

On armv8 the mb macro is defined as dsb(sy) - Given that the etm4x is
only used on armv8 let's directly use dsb(sy) instead of mb(). This
removes some ambiguity and makes it easier to correlate the code with
the TRM.

Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[Fixed capital letter for "use" in title]
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20190829202842.580-11-mathieu.poirier@linaro.org
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: caam - fix concurrency issue in givencrypt descriptor

commit 48f89d2a2920166c35b1c0b69917dbb0390ebec7 upstream.

IV transfer from ofifo to class2 (set up at [29][30]) is not guaranteed
to be scheduled before the data transfer from ofifo to external memory
(set up at [38]:

[29] 10FA0004           ld: ind-nfifo (len=4) imm
[30] 81F00010               <nfifo_entry: ofifo->class2 type=msg len=16>
[31] 14820004           ld: ccb2-datasz len=4 offs=0 imm
[32] 00000010               data:0x00000010
[33] 8210010D    operation: cls1-op aes cbc init-final enc
[34] A8080B04         math: (seqin + math0)->vseqout len=4
[35] 28000010    seqfifold: skip len=16
[36] A8080A04         math: (seqin + math0)->vseqin len=4
[37] 2F1E0000    seqfifold: both msg1->2-last2-last1 len=vseqinsz
[38] 69300000   seqfifostr: msg len=vseqoutsz
[39] 5C20000C      seqstr: ccb2 ctx len=12 offs=0

If ofifo -> external memory transfer happens first, DECO will hang
(issuing a Watchdog Timeout error, if WDOG is enabled) waiting for
data availability in ofifo for the ofifo -> c2 ififo transfer.

Make sure IV transfer happens first by waiting for all CAAM internal
transfers to end before starting payload transfer.

New descriptor with jump command inserted at [37]:

[..]
[36] A8080A04         math: (seqin + math0)->vseqin len=4
[37] A1000401         jump: jsl1 all-match[!nfifopend] offset=[01] local->[38]
[38] 2F1E0000    seqfifold: both msg1->2-last2-last1 len=vseqinsz
[39] 69300000   seqfifostr: msg len=vseqoutsz
[40] 5C20000C      seqstr: ccb2 ctx len=12 offs=0

[Note: the issue is present in the descriptor from the very beginning
(cf. Fixes tag). However I've marked it v4.19+ since it's the oldest
maintained kernel that the patch applies clean against.]

Cc: <stable@vger.kernel.org> # v4.19+
Fixes: 1acebad3d8db8 ("crypto: caam - faster aead implementation")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
[Horia: backport to v4.4, v4.9]
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf stat: Reset previous counts on repeat with interval

[ Upstream commit b63fd11cced17fcb8e133def29001b0f6aaa5e06 ]

When using 'perf stat' with repeat and interval option, it shows wrong
values for events.

The wrong values will be shown for the first interval on the second and
subsequent repetitions.

Without the fix:

  # perf stat -r 3 -I 2000 -e faults -e sched:sched_switch -a sleep 5

     2.000282489                 53      faults
     2.000282489                513      sched:sched_switch
     4.005478208              3,721      faults
     4.005478208              2,666      sched:sched_switch
     5.025470933                395      faults
     5.025470933              1,307      sched:sched_switch
     2.009602825 1,84,46,74,40,73,70,95,47,520      faults  <------
     2.009602825 1,84,46,74,40,73,70,95,49,568      sched:sched_switch  <------
     4.019612206              4,730      faults
     4.019612206              2,746      sched:sched_switch
     5.039615484              3,953      faults
     5.039615484              1,496      sched:sched_switch
     2.000274620 1,84,46,74,40,73,70,95,47,520      faults <------
     2.000274620 1,84,46,74,40,73,70,95,47,520      sched:sched_switch <------
     4.000480342              4,282      faults
     4.000480342              2,303      sched:sched_switch
     5.000916811              1,322      faults
     5.000916811              1,064      sched:sched_switch
  #

prev_raw_counts is allocated when using intervals. This is used when
calculating the difference in the counts of events when using interval.

The current counts are stored in prev_raw_counts to calculate the
differences in the next iteration.

On the first interval of the second and subsequent repetitions,
prev_raw_counts would be the values stored in the last interval of the
previous repetitions, while the current counts will only be for the
first interval of the current repetition.

Hence there is a possibility of events showing up as big number.

Fix this by resetting prev_raw_counts whenever perf stat repeats the
command.

With the fix:

  # perf stat -r 3 -I 2000 -e faults -e sched:sched_switch -a sleep 5

     2.019349347              2,597      faults
     2.019349347              2,753      sched:sched_switch
     4.019577372              3,098      faults
     4.019577372              2,532      sched:sched_switch
     5.019415481              1,879      faults
     5.019415481              1,356      sched:sched_switch
     2.000178813              8,468      faults
     2.000178813              2,254      sched:sched_switch
     4.000404621              7,440      faults
     4.000404621              1,266      sched:sched_switch
     5.040196079              2,458      faults
     5.040196079                556      sched:sched_switch
     2.000191939              6,870      faults
     2.000191939              1,170      sched:sched_switch
     4.000414103                541      faults
     4.000414103                902      sched:sched_switch
     5.000809863                450      faults
     5.000809863                364      sched:sched_switch
  #

Committer notes:

This was broken since the cset introducing the --interval feature, i.e.
--repeat + --interval wasn't tested at that point, add the Fixes tag so
that automatic scripts can pick this up.

Fixes: 13370a9b5bb8 ("perf stat: Add interval printing")
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Tested-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: stable@vger.kernel.org # v3.9+
Link: http://lore.kernel.org/lkml/20190904094738.9558-2-srikar@linux.vnet.ibm.com
[ Fixed up conflicts with libperf, i.e. some perf_{evsel,evlist} lost the 'perf' prefix ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf stat: Fix a segmentation fault when using repeat forever

[ Upstream commit 443f2d5ba13d65ccfd879460f77941875159d154 ]

Observe a segmentation fault when 'perf stat' is asked to repeat forever
with the interval option.

Without fix:

  # perf stat -r 0 -I 5000 -e cycles -a sleep 10
  #           time             counts unit events
       5.000211692  3,13,89,82,34,157      cycles
      10.000380119  1,53,98,52,22,294      cycles
      10.040467280       17,16,79,265      cycles
  Segmentation fault

This problem was only observed when we use forever option aka -r 0 and
works with limited repeats. Calling print_counter with ts being set to
NULL, is not a correct option when interval is set. Hence avoid
print_counter(NULL,..)  if interval is set.

With fix:

  # perf stat -r 0 -I 5000 -e cycles -a sleep 10
   #           time             counts unit events
       5.019866622  3,15,14,43,08,697      cycles
      10.039865756  3,15,16,31,95,261      cycles
      10.059950628     1,26,05,47,158      cycles
       5.009902655  3,14,52,62,33,932      cycles
      10.019880228  3,14,52,22,89,154      cycles
      10.030543876       66,90,18,333      cycles
       5.009848281  3,14,51,98,25,437      cycles
      10.029854402  3,15,14,93,04,918      cycles
       5.009834177  3,14,51,95,92,316      cycles

Committer notes:

Did the 'git bisect' to find the cset introducing the problem to add the
Fixes tag below, and at that time the problem reproduced as:

  (gdb) run stat -r0 -I500 sleep 1
  <SNIP>
  Program received signal SIGSEGV, Segmentation fault.
  print_interval (prefix=prefix@entry=0x7fffffffc8d0 "", ts=ts@entry=0x0) at builtin-stat.c:866
  866 sprintf(prefix, "%6lu.%09lu%s", ts->tv_sec, ts->tv_nsec, csv_sep);
  (gdb) bt
  #0  print_interval (prefix=prefix@entry=0x7fffffffc8d0 "", ts=ts@entry=0x0) at builtin-stat.c:866
  #1  0x000000000041860a in print_counters (ts=ts@entry=0x0, argc=argc@entry=2, argv=argv@entry=0x7fffffffd640) at builtin-stat.c:938
  #2  0x0000000000419a7f in cmd_stat (argc=2, argv=0x7fffffffd640, prefix=<optimized out>) at builtin-stat.c:1411
  #3  0x000000000045c65a in run_builtin (p=p@entry=0x6291b8 <commands+216>, argc=argc@entry=5, argv=argv@entry=0x7fffffffd640) at perf.c:370
  #4  0x000000000045c893 in handle_internal_command (argc=5, argv=0x7fffffffd640) at perf.c:429
  #5  0x000000000045c8f1 in run_argv (argcp=argcp@entry=0x7fffffffd4ac, argv=argv@entry=0x7fffffffd4a0) at perf.c:473
  #6  0x000000000045cac9 in main (argc=<optimized out>, argv=<optimized out>) at perf.c:588
  (gdb)

Mostly the same as just before this patch:

  Program received signal SIGSEGV, Segmentation fault.
  0x00000000005874a7 in print_interval (config=0xa1f2a0 <stat_config>, evlist=0xbc9b90, prefix=0x7fffffffd1c0 "`", ts=0x0) at util/stat-display.c:964
  964 sprintf(prefix, "%6lu.%09lu%s", ts->tv_sec, ts->tv_nsec, config->csv_sep);
  (gdb) bt
  #0  0x00000000005874a7 in print_interval (config=0xa1f2a0 <stat_config>, evlist=0xbc9b90, prefix=0x7fffffffd1c0 "`", ts=0x0) at util/stat-display.c:964
  #1  0x0000000000588047 in perf_evlist__print_counters (evlist=0xbc9b90, config=0xa1f2a0 <stat_config>, _target=0xa1f0c0 <target>, ts=0x0, argc=2, argv=0x7fffffffd670)
      at util/stat-display.c:1172
  #2  0x000000000045390f in print_counters (ts=0x0, argc=2, argv=0x7fffffffd670) at builtin-stat.c:656
  #3  0x0000000000456bb5 in cmd_stat (argc=2, argv=0x7fffffffd670) at builtin-stat.c:1960
  #4  0x00000000004dd2e0 in run_builtin (p=0xa30e00 <commands+288>, argc=5, argv=0x7fffffffd670) at perf.c:310
  #5  0x00000000004dd54d in handle_internal_command (argc=5, argv=0x7fffffffd670) at perf.c:362
  #6  0x00000000004dd694 in run_argv (argcp=0x7fffffffd4cc, argv=0x7fffffffd4c0) at perf.c:406
  #7  0x00000000004dda11 in main (argc=5, argv=0x7fffffffd670) at perf.c:531
  (gdb)

Fixes: d4f63a4741a8 ("perf stat: Introduce print_counters function")
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Tested-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # v4.2+
Link: http://lore.kernel.org/lkml/20190904094738.9558-3-srikar@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf tools: Fix segfault in cpu_cache_level__read()

[ Upstream commit 0216234c2eed1367a318daeb9f4a97d8217412a0 ]

We release wrong pointer on error path in cpu_cache_level__read
function, leading to segfault:

  (gdb) r record ls
  Starting program: /root/perf/tools/perf/perf record ls
  ...
  [ perf record: Woken up 1 times to write data ]
  double free or corruption (out)

  Thread 1 "perf" received signal SIGABRT, Aborted.
  0x00007ffff7463798 in raise () from /lib64/power9/libc.so.6
  (gdb) bt
  #0  0x00007ffff7463798 in raise () from /lib64/power9/libc.so.6
  #1  0x00007ffff7443bac in abort () from /lib64/power9/libc.so.6
  #2  0x00007ffff74af8bc in __libc_message () from /lib64/power9/libc.so.6
  #3  0x00007ffff74b92b8 in malloc_printerr () from /lib64/power9/libc.so.6
  #4  0x00007ffff74bb874 in _int_free () from /lib64/power9/libc.so.6
  #5  0x0000000010271260 in __zfree (ptr=0x7fffffffa0b0) at ../../lib/zalloc..
  #6  0x0000000010139340 in cpu_cache_level__read (cache=0x7fffffffa090, cac..
  #7  0x0000000010143c90 in build_caches (cntp=0x7fffffffa118, size=<optimiz..
  ...

Releasing the proper pointer.

Fixes: 720e98b5faf1 ("perf tools: Add perf data cache feature")
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org: # v4.6+
Link: http://lore.kernel.org/lkml/20190912105235.10689-1-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tools lib traceevent: Do not free tep->cmdlines in add_new_comm() on failure

[ Upstream commit e0d2615856b2046c2e8d5bfd6933f37f69703b0b ]

If the re-allocation of tep->cmdlines succeeds, then the previous
allocation of tep->cmdlines will be freed. If we later fail in
add_new_comm(), we must not free cmdlines, and also should assign
tep->cmdlines to the new allocation. Otherwise when freeing tep, the
tep->cmdlines will be pointing to garbage.

Fixes: a6d2a61ac653a ("tools lib traceevent: Remove some die() calls")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: linux-trace-devel@vger.kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20190828191819.970121417@goodmis.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

kernel/elfcore.c: include proper prototypes

[ Upstream commit 0f74914071ab7e7b78731ed62bf350e3a344e0a5 ]

When building with W=1, gcc properly complains that there's no prototypes:

  CC      kernel/elfcore.o
kernel/elfcore.c:7:17: warning: no previous prototype for 'elf_core_extra_phdrs' [-Wmissing-prototypes]
    7 | Elf_Half __weak elf_core_extra_phdrs(void)
      |                 ^~~~~~~~~~~~~~~~~~~~
kernel/elfcore.c:12:12: warning: no previous prototype for 'elf_core_write_extra_phdrs' [-Wmissing-prototypes]
   12 | int __weak elf_core_write_extra_phdrs(struct coredump_params *cprm, loff_t offset)
      |            ^~~~~~~~~~~~~~~~~~~~~~~~~~
kernel/elfcore.c:17:12: warning: no previous prototype for 'elf_core_write_extra_data' [-Wmissing-prototypes]
   17 | int __weak elf_core_write_extra_data(struct coredump_params *cprm)
      |            ^~~~~~~~~~~~~~~~~~~~~~~~~
kernel/elfcore.c:22:15: warning: no previous prototype for 'elf_core_extra_data_size' [-Wmissing-prototypes]
   22 | size_t __weak elf_core_extra_data_size(void)
      |               ^~~~~~~~~~~~~~~~~~~~~~~~

Provide the include file so gcc is happy, and we don't have potential code drift

Link: http://lkml.kernel.org/r/29875.1565224705@turing-police
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

sched/core: Fix migration to invalid CPU in __set_cpus_allowed_ptr()

[ Upstream commit 714e501e16cd473538b609b3e351b2cc9f7f09ed ]

An oops can be triggered in the scheduler when running qemu on arm64:

 Unable to handle kernel paging request at virtual address ffff000008effe40
 Internal error: Oops: 96000007 [#1] SMP
 Process migration/0 (pid: 12, stack limit = 0x00000000084e3736)
 pstate: 20000085 (nzCv daIf -PAN -UAO)
 pc : __ll_sc___cmpxchg_case_acq_4+0x4/0x20
 lr : move_queued_task.isra.21+0x124/0x298
 ...
 Call trace:
  __ll_sc___cmpxchg_case_acq_4+0x4/0x20
  __migrate_task+0xc8/0xe0
  migration_cpu_stop+0x170/0x180
  cpu_stopper_thread+0xec/0x178
  smpboot_thread_fn+0x1ac/0x1e8
  kthread+0x134/0x138
  ret_from_fork+0x10/0x18

__set_cpus_allowed_ptr() will choose an active dest_cpu in affinity mask to
migrage the process if process is not currently running on any one of the
CPUs specified in affinity mask. __set_cpus_allowed_ptr() will choose an
invalid dest_cpu (dest_cpu >= nr_cpu_ids, 1024 in my virtual machine) if
CPUS in an affinity mask are deactived by cpu_down after cpumask_intersects
check. cpumask_test_cpu() of dest_cpu afterwards is overflown and may pass if
corresponding bit is coincidentally set. As a consequence, kernel will
access an invalid rq address associate with the invalid CPU in
migration_cpu_stop->__migrate_task->move_queued_task and the Oops occurs.

The reproduce the crash:

  1) A process repeatedly binds itself to cpu0 and cpu1 in turn by calling
  sched_setaffinity.

  2) A shell script repeatedly does "echo 0 > /sys/devices/system/cpu/cpu1/online"
  and "echo 1 > /sys/devices/system/cpu/cpu1/online" in turn.

  3) Oops appears if the invalid CPU is set in memory after tested cpumask.

Signed-off-by: KeMeng Shi <shikemeng@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/1568616808-16808-1-git-send-email-shikemeng@huawei.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fuse: fix memleak in cuse_channel_open

[ Upstream commit 9ad09b1976c562061636ff1e01bfc3a57aebe56b ]

If cuse_send_init fails, need to fuse_conn_put cc->fc.

cuse_channel_open->fuse_conn_init->refcount_set(&fc->count, 1)
                 ->fuse_dev_alloc->fuse_conn_get
                 ->fuse_dev_free->fuse_conn_put

Fixes: cc080e9e9be1 ("fuse: introduce per-instance fuse_dev structure")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

thermal: Fix use-after-free when unregistering thermal zone device

[ Upstream commit 1851799e1d2978f68eea5d9dff322e121dcf59c1 ]

thermal_zone_device_unregister() cancels the delayed work that polls the
thermal zone, but it does not wait for it to finish. This is racy with
respect to the freeing of the thermal zone device, which can result in a
use-after-free [1].

Fix this by waiting for the delayed work to finish before freeing the
thermal zone device. Note that thermal_zone_device_set_polling() is
never invoked from an atomic context, so it is safe to call
cancel_delayed_work_sync() that can block.

[1]
[  +0.002221] ==================================================================
[  +0.000064] BUG: KASAN: use-after-free in __mutex_lock+0x1076/0x11c0
[  +0.000016] Read of size 8 at addr ffff8881e48e0450 by task kworker/1:0/17

[  +0.000023] CPU: 1 PID: 17 Comm: kworker/1:0 Not tainted 5.2.0-rc6-custom-02495-g8e73ca3be4af #1701
[  +0.000010] Hardware name: Mellanox Technologies Ltd. MSN2100-CB2FO/SA001017, BIOS 5.6.5 06/07/2016
[  +0.000016] Workqueue: events_freezable_power_ thermal_zone_device_check
[  +0.000012] Call Trace:
[  +0.000021]  dump_stack+0xa9/0x10e
[  +0.000020]  print_address_description.cold.2+0x9/0x25e
[  +0.000018]  __kasan_report.cold.3+0x78/0x9d
[  +0.000016]  kasan_report+0xe/0x20
[  +0.000016]  __mutex_lock+0x1076/0x11c0
[  +0.000014]  step_wise_throttle+0x72/0x150
[  +0.000018]  handle_thermal_trip+0x167/0x760
[  +0.000019]  thermal_zone_device_update+0x19e/0x5f0
[  +0.000019]  process_one_work+0x969/0x16f0
[  +0.000017]  worker_thread+0x91/0xc40
[  +0.000014]  kthread+0x33d/0x400
[  +0.000015]  ret_from_fork+0x3a/0x50

[  +0.000020] Allocated by task 1:
[  +0.000015]  save_stack+0x19/0x80
[  +0.000015]  __kasan_kmalloc.constprop.4+0xc1/0xd0
[  +0.000014]  kmem_cache_alloc_trace+0x152/0x320
[  +0.000015]  thermal_zone_device_register+0x1b4/0x13a0
[  +0.000015]  mlxsw_thermal_init+0xc92/0x23d0
[  +0.000014]  __mlxsw_core_bus_device_register+0x659/0x11b0
[  +0.000013]  mlxsw_core_bus_device_register+0x3d/0x90
[  +0.000013]  mlxsw_pci_probe+0x355/0x4b0
[  +0.000014]  local_pci_probe+0xc3/0x150
[  +0.000013]  pci_device_probe+0x280/0x410
[  +0.000013]  really_probe+0x26a/0xbb0
[  +0.000013]  driver_probe_device+0x208/0x2e0
[  +0.000013]  device_driver_attach+0xfe/0x140
[  +0.000013]  __driver_attach+0x110/0x310
[  +0.000013]  bus_for_each_dev+0x14b/0x1d0
[  +0.000013]  driver_register+0x1c0/0x400
[  +0.000015]  mlxsw_sp_module_init+0x5d/0xd3
[  +0.000014]  do_one_initcall+0x239/0x4dd
[  +0.000013]  kernel_init_freeable+0x42b/0x4e8
[  +0.000012]  kernel_init+0x11/0x18b
[  +0.000013]  ret_from_fork+0x3a/0x50

[  +0.000015] Freed by task 581:
[  +0.000013]  save_stack+0x19/0x80
[  +0.000014]  __kasan_slab_free+0x125/0x170
[  +0.000013]  kfree+0xf3/0x310
[  +0.000013]  thermal_release+0xc7/0xf0
[  +0.000014]  device_release+0x77/0x200
[  +0.000014]  kobject_put+0x1a8/0x4c0
[  +0.000014]  device_unregister+0x38/0xc0
[  +0.000014]  thermal_zone_device_unregister+0x54e/0x6a0
[  +0.000014]  mlxsw_thermal_fini+0x184/0x35a
[  +0.000014]  mlxsw_core_bus_device_unregister+0x10a/0x640
[  +0.000013]  mlxsw_devlink_core_bus_device_reload+0x92/0x210
[  +0.000015]  devlink_nl_cmd_reload+0x113/0x1f0
[  +0.000014]  genl_family_rcv_msg+0x700/0xee0
[  +0.000013]  genl_rcv_msg+0xca/0x170
[  +0.000013]  netlink_rcv_skb+0x137/0x3a0
[  +0.000012]  genl_rcv+0x29/0x40
[  +0.000013]  netlink_unicast+0x49b/0x660
[  +0.000013]  netlink_sendmsg+0x755/0xc90
[  +0.000013]  __sys_sendto+0x3de/0x430
[  +0.000013]  __x64_sys_sendto+0xe2/0x1b0
[  +0.000013]  do_syscall_64+0xa4/0x4d0
[  +0.000013]  entry_SYSCALL_64_after_hwframe+0x49/0xbe

[  +0.000017] The buggy address belongs to the object at ffff8881e48e0008
               which belongs to the cache kmalloc-2k of size 2048
[  +0.000012] The buggy address is located 1096 bytes inside of
               2048-byte region [ffff8881e48e0008, ffff8881e48e0808)
[  +0.000007] The buggy address belongs to the page:
[  +0.000012] page:ffffea0007923800 refcount:1 mapcount:0 mapping:ffff88823680d0c0 index:0x0 compound_mapcount: 0
[  +0.000020] flags: 0x200000000010200(slab|head)
[  +0.000019] raw: 0200000000010200 ffffea0007682008 ffffea00076ab808 ffff88823680d0c0
[  +0.000016] raw: 0000000000000000 00000000000d000d 00000001ffffffff 0000000000000000
[  +0.000007] page dumped because: kasan: bad access detected

[  +0.000012] Memory state around the buggy address:
[  +0.000012]  ffff8881e48e0300: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  +0.000012]  ffff8881e48e0380: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  +0.000012] >ffff8881e48e0400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  +0.000008]                                                  ^
[  +0.000012]  ffff8881e48e0480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  +0.000012]  ffff8881e48e0500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  +0.000007] ==================================================================

Fixes: b1569e99c795 ("ACPI: move thermal trip handling to generic thermal layer")
Reported-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu: Check for valid number of registers to read

[ Upstream commit 73d8e6c7b841d9bf298c8928f228fb433676635c ]

Do not try to allocate any amount of memory requested by the user.
Instead limit it to 128 registers. Actually the longest series of
consecutive allowed registers are 48, mmGB_TILE_MODE0-31 and
mmGB_MACROTILE_MODE0-15 (0x2644-0x2673).

Bug: https://bugs.freedesktop.org/show_bug.cgi?id=111273
Signed-off-by: Trek <trek00@inbox.ru>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ceph: reconnect connection if session hang in opening state

[ Upstream commit 71a228bc8d65900179e37ac309e678f8c523f133 ]

If client mds session is evicted in CEPH_MDS_SESSION_OPENING state,
mds won't send session msg to client, and delayed_work skip
CEPH_MDS_SESSION_OPENING state session, the session hang forever.

Allow ceph_con_keepalive to reconnect a session in OPENING to avoid
session hang. Also, ensure that we skip sessions in RESTARTING and
REJECTED states since those states can't be resurrected by issuing
a keepalive.

Link: https://tracker.ceph.com/issues/41551
Signed-off-by: Erqi Chen chenerqi@gmail.com
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ceph: fix directories inode i_blkbits initialization

[ Upstream commit 750670341a24cb714e624e0fd7da30900ad93752 ]

When filling an inode with info from the MDS, i_blkbits is being
initialized using fl_stripe_unit, which contains the stripe unit in
bytes.  Unfortunately, this doesn't make sense for directories as they
have fl_stripe_unit set to '0'.  This means that i_blkbits will be set
to 0xff, causing an UBSAN undefined behaviour in i_blocksize():

  UBSAN: Undefined behaviour in ./include/linux/fs.h:731:12
  shift exponent 255 is too large for 32-bit type 'int'

Fix this by initializing i_blkbits to CEPH_BLOCK_SHIFT if fl_stripe_unit
is zero.

Signed-off-by: Luis Henriques <lhenriques@suse.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

xen/pci: reserve MCFG areas earlier

[ Upstream commit a4098bc6eed5e31e0391bcc068e61804c98138df ]

If MCFG area is not reserved in E820, Xen by default will defer its usage
until Dom0 registers it explicitly after ACPI parser recognizes it as
a reserved resource in DSDT. Having it reserved in E820 is not
mandatory according to "PCI Firmware Specification, rev 3.2" (par. 4.1.2)
and firmware is free to keep a hole in E820 in that place. Xen doesn't know
what exactly is inside this hole since it lacks full ACPI view of the
platform therefore it's potentially harmful to access MCFG region
without additional checks as some machines are known to provide
inconsistent information on the size of the region.

Now xen_mcfg_late() runs after acpi_init() which is too late as some basic
PCI enumeration starts exactly there as well. Trying to register a device
prior to MCFG reservation causes multiple problems with PCIe extended
capability initializations in Xen (e.g. SR-IOV VF BAR sizing). There are
no convenient hooks for us to subscribe to so register MCFG areas earlier
upon the first invocation of xen_add_device(). It should be safe to do once
since all the boot time buses must have their MCFG areas in MCFG table
already and we don't support PCI bus hot-plug.

Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

9p: avoid attaching writeback_fid on mmap with type PRIVATE

[ Upstream commit c87a37ebd40b889178664c2c09cc187334146292 ]

Currently on mmap cache policy, we always attach writeback_fid
whether mmap type is SHARED or PRIVATE. However, in the use case
of kata-container which combines 9p(Guest OS) with overlayfs(Host OS),
this behavior will trigger overlayfs' copy-up when excute command
inside container.

Link: http://lkml.kernel.org/r/20190820100325.10313-1-cgxu519@zoho.com.cn
Signed-off-by: Chengguang Xu <cgxu519@zoho.com.cn>
Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fs: nfs: Fix possible null-pointer dereferences in encode_attrs()

[ Upstream commit e2751463eaa6f9fec8fea80abbdc62dbc487b3c5 ]

In encode_attrs(), there is an if statement on line 1145 to check
whether label is NULL:
    if (label && (attrmask[2] & FATTR4_WORD2_SECURITY_LABEL))

When label is NULL, it is used on lines 1178-1181:
    *p++ = cpu_to_be32(label->lfs);
    *p++ = cpu_to_be32(label->pi);
    *p++ = cpu_to_be32(label->len);
    p = xdr_encode_opaque_fixed(p, label->label, label->len);

To fix these bugs, label is checked before being used.

These bugs are found by a static analysis tool STCheck written by us.

Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ima: always return negative code for error

[ Upstream commit f5e1040196dbfe14c77ce3dfe3b7b08d2d961e88 ]

integrity_kernel_read() returns the number of bytes read. If this is
a short read then this positive value is returned from
ima_calc_file_hash_atfm(). Currently this is only indirectly called from
ima_calc_file_hash() and this function only tests for the return value
being zero or nonzero and also doesn't forward the return value.
Nevertheless there's no point in returning a positive value as an error,
so translate a short read into -EINVAL.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

cfg80211: initialize on-stack chandefs

commit f43e5210c739fe76a4b0ed851559d6902f20ceb1 upstream.

In a few places we don't properly initialize on-stack chandefs,
resulting in EDMG data to be non-zero, which broke things.

Additionally, in a few places we rely on the driver to init the
data completely, but perhaps we shouldn't as non-EDMG drivers
may not initialize the EDMG data, also initialize it there.

Cc: stable@vger.kernel.org
Fixes: 2a38075cd0be ("nl80211: Add support for EDMG channels")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/1569239475-I2dcce394ecf873376c386a78f31c2ec8b538fa25@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ieee802154: atusb: fix use-after-free at disconnect

commit 7fd25e6fc035f4b04b75bca6d7e8daa069603a76 upstream.

The disconnect callback was accessing the hardware-descriptor private
data after having having freed it.

Fixes: 7490b008d123 ("ieee802154: add support for atusb transceiver")
Cc: stable <stable@vger.kernel.org> # 4.2
Cc: Alexander Aring <alex.aring@gmail.com>
Reported-by: syzbot+f4509a9138a1472e7e80@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

watchdog: imx2_wdt: fix min() calculation in imx2_wdt_set_timeout

commit 144783a80cd2cbc45c6ce17db649140b65f203dd upstream.

Converting from ms to s requires dividing by 1000, not multiplying. So
this is currently taking the smaller of new_timeout and 1.28e8,
i.e. effectively new_timeout.

The driver knows what it set max_hw_heartbeat_ms to, so use that
value instead of doing a division at run-time.

FWIW, this can easily be tested by booting into a busybox shell and
doing "watchdog -t 5 -T 130 /dev/watchdog" - without this patch, the
watchdog fires after 130&127 == 2 seconds.

Fixes: b07e228eee69 "watchdog: imx2_wdt: Fix set_timeout for big timeout values"
Cc: stable@vger.kernel.org # 5.2 plus anything the above got backported to
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812131356.23039-1-linux@rasmusvillemoes.dk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

timer: Read jiffies once when forwarding base clk

commit e430d802d6a3aaf61bd3ed03d9404888a29b9bf9 upstream.

The timer delayed for more than 3 seconds warning was triggered during
testing.

  Workqueue: events_unbound sched_tick_remote
  RIP: 0010:sched_tick_remote+0xee/0x100
  ...
  Call Trace:
   process_one_work+0x18c/0x3a0
   worker_thread+0x30/0x380
   kthread+0x113/0x130
   ret_from_fork+0x22/0x40

The reason is that the code in collect_expired_timers() uses jiffies
unprotected:

    if (next_event > jiffies)
        base->clk = jiffies;

As the compiler is allowed to reload the value base->clk can advance
between the check and the store and in the worst case advance farther than
next event. That causes the timer expiry to be delayed until the wheel
pointer wraps around.

Convert the code to use READ_ONCE()

Fixes: 236968383cf5 ("timers: Optimize collect_expired_timers() for NOHZ")
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Liang ZhiCheng <liangzhicheng@baidu.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1568894687-14499-1-git-send-email-lirongqing@baidu.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usercopy: Avoid HIGHMEM pfn warning

commit 314eed30ede02fa925990f535652254b5bad6b65 upstream.

When running on a system with >512MB RAM with a 32-bit kernel built with:

CONFIG_DEBUG_VIRTUAL=y
CONFIG_HIGHMEM=y
CONFIG_HARDENED_USERCOPY=y

all execve()s will fail due to argv copying into kmap()ed pages, and on
usercopy checking the calls ultimately of virt_to_page() will be looking
for "bad" kmap (highmem) pointers due to CONFIG_DEBUG_VIRTUAL=y:

 ------------[ cut here ]------------
 kernel BUG at ../arch/x86/mm/physaddr.c:83!
 invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
 CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.3.0-rc8 #6
 Hardware name: Dell Inc. Inspiron 1318/0C236D, BIOS A04 01/15/2009
 EIP: __phys_addr+0xaf/0x100
 ...
 Call Trace:
  __check_object_size+0xaf/0x3c0
  ? __might_sleep+0x80/0xa0
  copy_strings+0x1c2/0x370
  copy_strings_kernel+0x2b/0x40
  __do_execve_file+0x4ca/0x810
  ? kmem_cache_alloc+0x1c7/0x370
  do_execve+0x1b/0x20
  ...

The check is from arch/x86/mm/physaddr.c:

VIRTUAL_BUG_ON((phys_addr >> PAGE_SHIFT) > max_low_pfn);

Due to the kmap() in fs/exec.c:

kaddr = kmap(kmapped_page);
...
if (copy_from_user(kaddr+offset, str, bytes_to_copy)) ...

Now we can fetch the correct page to avoid the pfn check. In both cases,
hardened usercopy will need to walk the page-span checker (if enabled)
to do sanity checking.

Reported-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: f5509cc18daa ("mm: Hardened usercopy")
Cc: Matthew Wilcox <willy@infradead.org>
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Link: https://lore.kernel.org/r/201909171056.7F2FFD17@keescook
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: qat - Silence smp_processor_id() warning

commit 1b82feb6c5e1996513d0fb0bbb475417088b4954 upstream.

It seems that smp_processor_id() is only used for a best-effort
load-balancing, refer to qat_crypto_get_instance_node(). It's not feasible
to disable preemption for the duration of the crypto requests. Therefore,
just silence the warning. This commit is similar to e7a9b05ca4
("crypto: cavium - Fix smp_processor_id() warnings").

Silences the following splat:
BUG: using smp_processor_id() in preemptible [00000000] code: cryptomgr_test/2904
caller is qat_alg_ablkcipher_setkey+0x300/0x4a0 [intel_qat]
CPU: 1 PID: 2904 Comm: cryptomgr_test Tainted: P           O    4.14.69 #1
...
Call Trace:
 dump_stack+0x5f/0x86
 check_preemption_disabled+0xd3/0xe0
 qat_alg_ablkcipher_setkey+0x300/0x4a0 [intel_qat]
 skcipher_setkey_ablkcipher+0x2b/0x40
 __test_skcipher+0x1f3/0xb20
 ? cpumask_next_and+0x26/0x40
 ? find_busiest_group+0x10e/0x9d0
 ? preempt_count_add+0x49/0xa0
 ? try_module_get+0x61/0xf0
 ? crypto_mod_get+0x15/0x30
 ? __kmalloc+0x1df/0x1f0
 ? __crypto_alloc_tfm+0x116/0x180
 ? crypto_skcipher_init_tfm+0xa6/0x180
 ? crypto_create_tfm+0x4b/0xf0
 test_skcipher+0x21/0xa0
 alg_test_skcipher+0x3f/0xa0
 alg_test.part.6+0x126/0x2a0
 ? finish_task_switch+0x21b/0x260
 ? __schedule+0x1e9/0x800
 ? __wake_up_common+0x8d/0x140
 cryptomgr_test+0x40/0x50
 kthread+0xff/0x130
 ? cryptomgr_notify+0x540/0x540
 ? kthread_create_on_node+0x70/0x70
 ret_from_fork+0x24/0x50

Fixes: ed8ccaef52 ("crypto: qat - Add support for SRIOV")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: mcp251x: mcp251x_hw_reset(): allow more time after a reset

commit d84ea2123f8d27144e3f4d58cd88c9c6ddc799de upstream.

Some boards take longer than 5ms to power up after a reset, so allow
some retries attempts before giving up.

Fixes: ff06d611a31c ("can: mcp251x: Improve mcp251x_hw_reset()")
Cc: linux-stable <stable@vger.kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/powernv: Restrict OPAL symbol map to only be readable by root

commit e7de4f7b64c23e503a8c42af98d56f2a7462bd6d upstream.

Currently the OPAL symbol map is globally readable, which seems bad as
it contains physical addresses.

Restrict it to root.

Fixes: c8742f85125d ("powerpc/powernv: Expose OPAL firmware symbol map")
Cc: stable@vger.kernel.org # v3.19+
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190503075253.22798-1-ajd@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: Define a set of DAPM pre/post-up events

commit cfc8f568aada98f9608a0a62511ca18d647613e2 upstream.

Prepare to use SND_SOC_DAPM_PRE_POST_PMU definition to
reduce coming code size and make it more readable.

Cc: stable@vger.kernel.org
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20190719100524.23300-2-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: nVMX: handle page fault in vmread fix

During backport f7eea636c3d5 ("KVM: nVMX: handle page fault in vmread"),
there was a mistake the exception reference should be passed to function
kvm_write_guest_virt_system, instead of NULL, other wise, we will get
NULL pointer deref, eg

kvm-unit-test triggered a NULL pointer deref below:
[  948.518437] kvm [24114]: vcpu0, guest rIP: 0x407ef9 kvm_set_msr_common: MSR_IA32_DEBUGCTLMSR 0x3, nop
[  949.106464] BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
[  949.106707] PGD 0 P4D 0
[  949.106872] Oops: 0002 [#1] SMP
[  949.107038] CPU: 2 PID: 24126 Comm: qemu-2.7 Not tainted 4.19.77-pserver #4.19.77-1+feature+daily+update+20191005.1625+a4168bb~deb9
[  949.107283] Hardware name: Dell Inc. Precision Tower 3620/09WH54, BIOS 2.7.3 01/31/2018
[  949.107549] RIP: 0010:kvm_write_guest_virt_system+0x12/0x40 [kvm]
[  949.107719] Code: c0 5d 41 5c 41 5d 41 5e 83 f8 03 41 0f 94 c0 41 c1 e0 02 e9 b0 ed ff ff 0f 1f 44 00 00 48 89 f0 c6 87 59 56 00 00 01 48 89 d6 <49> c7 00 00 00 00 00 89 ca 49 c7 40 08 00 00 00 00 49 c7 40 10 00
[  949.108044] RSP: 0018:ffffb31b0a953cb0 EFLAGS: 00010202
[  949.108216] RAX: 000000000046b4d8 RBX: ffff9e9f415b0000 RCX: 0000000000000008
[  949.108389] RDX: ffffb31b0a953cc0 RSI: ffffb31b0a953cc0 RDI: ffff9e9f415b0000
[  949.108562] RBP: 00000000d2e14928 R08: 0000000000000000 R09: 0000000000000000
[  949.108733] R10: 0000000000000000 R11: 0000000000000000 R12: ffffffffffffffc8
[  949.108907] R13: 0000000000000002 R14: ffff9e9f4f26f2e8 R15: 0000000000000000
[  949.109079] FS:  00007eff8694c700(0000) GS:ffff9e9f51a80000(0000) knlGS:0000000031415928
[  949.109318] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  949.109495] CR2: 0000000000000000 CR3: 00000003be53b002 CR4: 00000000003626e0
[  949.109671] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  949.109845] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  949.110017] Call Trace:
[  949.110186]  handle_vmread+0x22b/0x2f0 [kvm_intel]
[  949.110356]  ? vmexit_fill_RSB+0xc/0x30 [kvm_intel]
[  949.110549]  kvm_arch_vcpu_ioctl_run+0xa98/0x1b30 [kvm]
[  949.110725]  ? kvm_vcpu_ioctl+0x388/0x5d0 [kvm]
[  949.110901]  kvm_vcpu_ioctl+0x388/0x5d0 [kvm]
[  949.111072]  do_vfs_ioctl+0xa2/0x620

Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>

s390/cio: exclude subchannels with no parent from pseudo check

commit ab5758848039de9a4b249d46e4ab591197eebaf2 upstream.

ccw console is created early in start_kernel and used before css is
initialized or ccw console subchannel is registered. Until then console
subchannel does not have a parent. For that reason assume subchannels
with no parent are not pseudo subchannels. This fixes the following
kasan finding:

BUG: KASAN: global-out-of-bounds in sch_is_pseudo_sch+0x8e/0x98
Read of size 8 at addr 00000000000005e8 by task swapper/0/0

CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.0-rc8-07370-g6ac43dd12538 #2
Hardware name: IBM 2964 NC9 702 (z/VM 6.4.0)
Call Trace:
([<000000000012cd76>] show_stack+0x14e/0x1e0)
 [<0000000001f7fb44>] dump_stack+0x1a4/0x1f8
 [<00000000007d7afc>] print_address_description+0x64/0x3c8
 [<00000000007d75f6>] __kasan_report+0x14e/0x180
 [<00000000018a2986>] sch_is_pseudo_sch+0x8e/0x98
 [<000000000189b950>] cio_enable_subchannel+0x1d0/0x510
 [<00000000018cac7c>] ccw_device_recognition+0x12c/0x188
 [<0000000002ceb1a8>] ccw_device_enable_console+0x138/0x340
 [<0000000002cf1cbe>] con3215_init+0x25e/0x300
 [<0000000002c8770a>] console_init+0x68a/0x9b8
 [<0000000002c6a3d6>] start_kernel+0x4fe/0x728
 [<0000000000100070>] startup_continue+0x70/0xd0

Cc: stable@vger.kernel.org
Reviewed-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/cio: avoid calling strlen on null pointer

commit ea298e6ee8b34b3ed4366be7eb799d0650ebe555 upstream.

Fix the following kasan finding:
BUG: KASAN: global-out-of-bounds in ccwgroup_create_dev+0x850/0x1140
Read of size 1 at addr 0000000000000000 by task systemd-udevd.r/561

CPU: 30 PID: 561 Comm: systemd-udevd.r Tainted: G    B
Hardware name: IBM 3906 M04 704 (LPAR)
Call Trace:
([<0000000231b3db7e>] show_stack+0x14e/0x1a8)
 [<0000000233826410>] dump_stack+0x1d0/0x218
 [<000000023216fac4>] print_address_description+0x64/0x380
 [<000000023216f5a8>] __kasan_report+0x138/0x168
 [<00000002331b8378>] ccwgroup_create_dev+0x850/0x1140
 [<00000002332b618a>] group_store+0x3a/0x50
 [<00000002323ac706>] kernfs_fop_write+0x246/0x3b8
 [<00000002321d409a>] vfs_write+0x132/0x450
 [<00000002321d47da>] ksys_write+0x122/0x208
 [<0000000233877102>] system_call+0x2a6/0x2c8

Triggered by:
openat(AT_FDCWD, "/sys/bus/ccwgroup/drivers/qeth/group",
O_WRONLY|O_CREAT|O_TRUNC|O_CLOEXEC, 0666) = 16
write(16, "0.0.bd00,0.0.bd01,0.0.bd02", 26) = 26

The problem is that __get_next_id in ccwgroup_create_dev might set "buf"
buffer pointer to NULL and explicit check for that is required.

Cc: stable@vger.kernel.org
Reviewed-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/topology: avoid firing events before kobjs are created

commit f3122a79a1b0a113d3aea748e0ec26f2cb2889de upstream.

arch_update_cpu_topology is first called from:
kernel_init_freeable->sched_init_smp->sched_init_domains

even before cpus has been registered in:
kernel_init_freeable->do_one_initcall->s390_smp_init

Do not trigger kobject_uevent change events until cpu devices are
actually created. Fixes the following kasan findings:

BUG: KASAN: global-out-of-bounds in kobject_uevent_env+0xb40/0xee0
Read of size 8 at addr 0000000000000020 by task swapper/0/1

BUG: KASAN: global-out-of-bounds in kobject_uevent_env+0xb36/0xee0
Read of size 8 at addr 0000000000000018 by task swapper/0/1

CPU: 0 PID: 1 Comm: swapper/0 Tainted: G    B
Hardware name: IBM 3906 M04 704 (LPAR)
Call Trace:
([<0000000143c6db7e>] show_stack+0x14e/0x1a8)
 [<0000000145956498>] dump_stack+0x1d0/0x218
 [<000000014429fb4c>] print_address_description+0x64/0x380
 [<000000014429f630>] __kasan_report+0x138/0x168
 [<0000000145960b96>] kobject_uevent_env+0xb36/0xee0
 [<0000000143c7c47c>] arch_update_cpu_topology+0x104/0x108
 [<0000000143df9e22>] sched_init_domains+0x62/0xe8
 [<000000014644c94a>] sched_init_smp+0x3a/0xc0
 [<0000000146433a20>] kernel_init_freeable+0x558/0x958
 [<000000014599002a>] kernel_init+0x22/0x160
 [<00000001459a71d4>] ret_from_fork+0x28/0x30
 [<00000001459a71dc>] kernel_thread_starter+0x0/0x10

Cc: stable@vger.kernel.org
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: s390: Test for bad access register and size at the start of S390_MEM_OP

commit a13b03bbb4575b350b46090af4dfd30e735aaed1 upstream.

If the KVM_S390_MEM_OP ioctl is called with an access register >= 16,
then there is certainly a bug in the calling userspace application.
We check for wrong access registers, but only if the vCPU was already
in the access register mode before (i.e. the SIE block has recorded
it). The check is also buried somewhere deep in the calling chain (in
the function ar_translation()), so this is somewhat hard to find.

It's better to always report an error to the userspace in case this
field is set wrong, and it's safer in the KVM code if we block wrong
values here early instead of relying on a check somewhere deep down
the calling chain, so let's add another check to kvm_s390_guest_mem_op()
directly.

We also should check that the "size" is non-zero here (thanks to Janosch
Frank for the hint!). If we do not check the size, we could call vmalloc()
with this 0 value, and this will cause a kernel warning.

Signed-off-by: Thomas Huth <thuth@redhat.com>
Link: https://lkml.kernel.org/r/20190829122517.31042-1-thuth@redhat.com
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.9.196

NFC: fix attrs checks in netlink interface

commit 18917d51472fe3b126a3a8f756c6b18085eb8130 upstream.

nfc_genl_deactivate_target() relies on the NFC_ATTR_TARGET_INDEX
attribute being present, but doesn't check whether it is actually
provided by the user. Same goes for nfc_genl_fw_download() and
NFC_ATTR_FIRMWARE_NAME.

This patch adds appropriate checks.

Found with syzkaller.

Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

smack: use GFP_NOFS while holding inode_smack::smk_lock

commit e5bfad3d7acc5702f32aafeb388362994f4d7bd0 upstream.

inode_smack::smk_lock is taken during smack_d_instantiate(), which is
called during a filesystem transaction when creating a file on ext4.
Therefore to avoid a deadlock, all code that takes this lock must use
GFP_NOFS, to prevent memory reclaim from waiting for the filesystem
transaction to complete.

Reported-by: syzbot+0eefc1e06a77d327a056@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Smack: Don't ignore other bprm->unsafe flags if LSM_UNSAFE_PTRACE is set

commit 3675f052b43ba51b99b85b073c7070e083f3e6fb upstream.

There is a logic bug in the current smack_bprm_set_creds():
If LSM_UNSAFE_PTRACE is set, but the ptrace state is deemed to be
acceptable (e.g. because the ptracer detached in the meantime), the other
->unsafe flags aren't checked. As far as I can tell, this means that
something like the following could work (but I haven't tested it):

 - task A: create task B with fork()
 - task B: set NO_NEW_PRIVS
 - task B: install a seccomp filter that makes open() return 0 under some
   conditions
 - task B: replace fd 0 with a malicious library
 - task A: attach to task B with PTRACE_ATTACH
 - task B: execve() a file with an SMACK64EXEC extended attribute
 - task A: while task B is still in the middle of execve(), exit (which
   destroys the ptrace relationship)

Make sure that if any flags other than LSM_UNSAFE_PTRACE are set in
bprm->unsafe, we reject the execve().

Cc: stable@vger.kernel.org
Fixes: 5663884caab1 ("Smack: unify all ptrace accesses in the smack")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv6: Handle missing host route in __ipv6_ifa_notify

[ Upstream commit 2d819d250a1393a3e725715425ab70a0e0772a71 ]

Rajendra reported a kernel panic when a link was taken down:

    [ 6870.263084] BUG: unable to handle kernel NULL pointer dereference at 00000000000000a8
    [ 6870.271856] IP: [<ffffffff8efc5764>] __ipv6_ifa_notify+0x154/0x290

    <snip>

    [ 6870.570501] Call Trace:
    [ 6870.573238] [<ffffffff8efc58c6>] ? ipv6_ifa_notify+0x26/0x40
    [ 6870.579665] [<ffffffff8efc98ec>] ? addrconf_dad_completed+0x4c/0x2c0
    [ 6870.586869] [<ffffffff8efe70c6>] ? ipv6_dev_mc_inc+0x196/0x260
    [ 6870.593491] [<ffffffff8efc9c6a>] ? addrconf_dad_work+0x10a/0x430
    [ 6870.600305] [<ffffffff8f01ade4>] ? __switch_to_asm+0x34/0x70
    [ 6870.606732] [<ffffffff8ea93a7a>] ? process_one_work+0x18a/0x430
    [ 6870.613449] [<ffffffff8ea93d6d>] ? worker_thread+0x4d/0x490
    [ 6870.619778] [<ffffffff8ea93d20>] ? process_one_work+0x430/0x430
    [ 6870.626495] [<ffffffff8ea99dd9>] ? kthread+0xd9/0xf0
    [ 6870.632145] [<ffffffff8f01ade4>] ? __switch_to_asm+0x34/0x70
    [ 6870.638573] [<ffffffff8ea99d00>] ? kthread_park+0x60/0x60
    [ 6870.644707] [<ffffffff8f01ae77>] ? ret_from_fork+0x57/0x70
    [ 6870.650936] Code: 31 c0 31 d2 41 b9 20 00 08 02 b9 09 00 00 0

addrconf_dad_work is kicked to be scheduled when a device is brought
up. There is a race between addrcond_dad_work getting scheduled and
taking the rtnl lock and a process taking the link down (under rtnl).
The latter removes the host route from the inet6_addr as part of
addrconf_ifdown which is run for NETDEV_DOWN. The former attempts
to use the host route in __ipv6_ifa_notify. If the down event removes
the host route due to the race to the rtnl, then the BUG listed above
occurs.

Since the DAD sequence can not be aborted, add a check for the missing
host route in __ipv6_ifa_notify. The only way this should happen is due
to the previously mentioned race. The host route is created when the
address is added to an interface; it is only removed on a down event
where the address is kept. Add a warning if the host route is missing
AND the device is up; this is a situation that should never happen.

Fixes: f1705ec197e7 ("net: ipv6: Make address flushing on ifdown optional")
Reported-by: Rajendra Dendukuri <rajendra.dendukuri@broadcom.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sch_cbq: validate TCA_CBQ_WRROPT to avoid crash

[ Upstream commit e9789c7cc182484fc031fd88097eb14cb26c4596 ]

syzbot reported a crash in cbq_normalize_quanta() caused
by an out of range cl->priority.

iproute2 enforces this check, but malicious users do not.

kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN PTI
Modules linked in:
CPU: 1 PID: 26447 Comm: syz-executor.1 Not tainted 5.3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:cbq_normalize_quanta.part.0+0x1fd/0x430 net/sched/sch_cbq.c:902
RSP: 0018:ffff8801a5c333b0 EFLAGS: 00010206
RAX: 0000000020000003 RBX: 00000000fffffff8 RCX: ffffc9000712f000
RDX: 00000000000043bf RSI: ffffffff83be8962 RDI: 0000000100000018
RBP: ffff8801a5c33420 R08: 000000000000003a R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 00000000000002ef
R13: ffff88018da95188 R14: dffffc0000000000 R15: 0000000000000015
FS:  00007f37d26b1700(0000) GS:ffff8801dad00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000004c7cec CR3: 00000001bcd0a006 CR4: 00000000001626f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 [<ffffffff83be9d57>] cbq_normalize_quanta include/net/pkt_sched.h:27 [inline]
 [<ffffffff83be9d57>] cbq_addprio net/sched/sch_cbq.c:1097 [inline]
 [<ffffffff83be9d57>] cbq_set_wrr+0x2d7/0x450 net/sched/sch_cbq.c:1115
 [<ffffffff83bee8a7>] cbq_change_class+0x987/0x225b net/sched/sch_cbq.c:1537
 [<ffffffff83b96985>] tc_ctl_tclass+0x555/0xcd0 net/sched/sch_api.c:2329
 [<ffffffff83a84655>] rtnetlink_rcv_msg+0x485/0xc10 net/core/rtnetlink.c:5248
 [<ffffffff83cadf0a>] netlink_rcv_skb+0x17a/0x460 net/netlink/af_netlink.c:2510
 [<ffffffff83a7db6d>] rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5266
 [<ffffffff83cac2c6>] netlink_unicast_kernel net/netlink/af_netlink.c:1324 [inline]
 [<ffffffff83cac2c6>] netlink_unicast+0x536/0x720 net/netlink/af_netlink.c:1350
 [<ffffffff83cacd4a>] netlink_sendmsg+0x89a/0xd50 net/netlink/af_netlink.c:1939
 [<ffffffff8399d46e>] sock_sendmsg_nosec net/socket.c:673 [inline]
 [<ffffffff8399d46e>] sock_sendmsg+0x12e/0x170 net/socket.c:684
 [<ffffffff8399f1fd>] ___sys_sendmsg+0x81d/0x960 net/socket.c:2359
 [<ffffffff839a2d05>] __sys_sendmsg+0x105/0x1d0 net/socket.c:2397
 [<ffffffff839a2df9>] SYSC_sendmsg net/socket.c:2406 [inline]
 [<ffffffff839a2df9>] SyS_sendmsg+0x29/0x30 net/socket.c:2404
 [<ffffffff8101ccc8>] do_syscall_64+0x528/0x770 arch/x86/entry/common.c:305
 [<ffffffff84400091>] entry_SYSCALL_64_after_hwframe+0x42/0xb7

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen-netfront: do not use ~0U as error return value for xennet_fill_frags()

[ Upstream commit a761129e3625688310aecf26e1be9e98e85f8eb5 ]

xennet_fill_frags() uses ~0U as return value when the sk_buff is not able
to cache extra fragments. This is incorrect because the return type of
xennet_fill_frags() is RING_IDX and 0xffffffff is an expected value for
ring buffer index.

In the situation when the rsp_cons is approaching 0xffffffff, the return
value of xennet_fill_frags() may become 0xffffffff which xennet_poll() (the
caller) would regard as error. As a result, queue->rx.rsp_cons is set
incorrectly because it is updated only when there is error. If there is no
error, xennet_poll() would be responsible to update queue->rx.rsp_cons.
Finally, queue->rx.rsp_cons would point to the rx ring buffer entries whose
queue->rx_skbs[i] and queue->grant_rx_ref[i] are already cleared to NULL.
This leads to NULL pointer access in the next iteration to process rx ring
buffer entries.

The symptom is similar to the one fixed in
commit 00b368502d18 ("xen-netfront: do not assume sk_buff_head list is
empty in error handling").

This patch changes the return type of xennet_fill_frags() to indicate
whether it is successful or failed. The queue->rx.rsp_cons will be
always updated inside this function.

Fixes: ad4f15dc2c70 ("xen/netfront: don't bug in case of too many frags")
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/rds: Fix error handling in rds_ib_add_one()

[ Upstream commit d64bf89a75b65f83f06be9fb8f978e60d53752db ]

rds_ibdev:ipaddr_list and rds_ibdev:conn_list are initialized
after allocation some resources such as protection domain.
If allocation of such resources fail, then these uninitialized
variables are accessed in rds_ib_dev_free() in failure path. This
can potentially crash the system. The code has been updated to
initialize these variables very early in the function.

Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Sudhakar Dindukurti <sudhakar.dindukurti@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sch_dsmark: fix potential NULL deref in dsmark_init()

[ Upstream commit 474f0813a3002cb299bb73a5a93aa1f537a80ca8 ]

Make sure TCA_DSMARK_INDICES was provided by the user.

syzbot reported :

kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 8799 Comm: syz-executor235 Not tainted 5.3.0+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:nla_get_u16 include/net/netlink.h:1501 [inline]
RIP: 0010:dsmark_init net/sched/sch_dsmark.c:364 [inline]
RIP: 0010:dsmark_init+0x193/0x640 net/sched/sch_dsmark.c:339
Code: 85 db 58 0f 88 7d 03 00 00 e8 e9 1a ac fb 48 8b 9d 70 ff ff ff 48 b8 00 00 00 00 00 fc ff df 48 8d 7b 04 48 89 fa 48 c1 ea 03 <0f> b6 14 02 48 89 f8 83 e0 07 83 c0 01 38 d0 7c 08 84 d2 0f 85 ca
RSP: 0018:ffff88809426f3b8 EFLAGS: 00010247
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: ffffffff85c6eb09
RDX: 0000000000000000 RSI: ffffffff85c6eb17 RDI: 0000000000000004
RBP: ffff88809426f4b0 R08: ffff88808c4085c0 R09: ffffed1015d26159
R10: ffffed1015d26158 R11: ffff8880ae930ac7 R12: ffff8880a7e96940
R13: dffffc0000000000 R14: ffff88809426f8c0 R15: 0000000000000000
FS:  0000000001292880(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020000080 CR3: 000000008ca1b000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 qdisc_create+0x4ee/0x1210 net/sched/sch_api.c:1237
 tc_modify_qdisc+0x524/0x1c50 net/sched/sch_api.c:1653
 rtnetlink_rcv_msg+0x463/0xb00 net/core/rtnetlink.c:5223
 netlink_rcv_skb+0x177/0x450 net/netlink/af_netlink.c:2477
 rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5241
 netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline]
 netlink_unicast+0x531/0x710 net/netlink/af_netlink.c:1328
 netlink_sendmsg+0x8a5/0xd60 net/netlink/af_netlink.c:1917
 sock_sendmsg_nosec net/socket.c:637 [inline]
 sock_sendmsg+0xd7/0x130 net/socket.c:657
 ___sys_sendmsg+0x803/0x920 net/socket.c:2311
 __sys_sendmsg+0x105/0x1d0 net/socket.c:2356
 __do_sys_sendmsg net/socket.c:2365 [inline]
 __se_sys_sendmsg net/socket.c:2363 [inline]
 __x64_sys_sendmsg+0x78/0xb0 net/socket.c:2363
 do_syscall_64+0xfa/0x760 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x440369

Fixes: 758cc43c6d73 ("[PKT_SCHED]: Fix dsmark to apply changes consistent")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

qmi_wwan: add support for Cinterion CLS8 devices

[ Upstream commit cf74ac6db25d4002089e85cc623ad149ecc25614 ]

Add support for Cinterion CLS8 devices.
Use QMI_QUIRK_SET_DTR as required for Qualcomm MDM9x07 chipsets.

T:  Bus=01 Lev=03 Prnt=05 Port=01 Cnt=02 Dev#= 25 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1e2d ProdID=00b0 Rev= 3.18
S:  Manufacturer=GEMALTO
S:  Product=USB Modem
C:* #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=89(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nfc: fix memory leak in llcp_sock_bind()

[ Upstream commit a0c2dc1fe63e2869b74c1c7f6a81d1745c8a695d ]

sysbot reported a memory leak after a bind() has failed.

While we are at it, abort the operation if kmemdup() has failed.

BUG: memory leak
unreferenced object 0xffff888105d83ec0 (size 32):
  comm "syz-executor067", pid 7207, jiffies 4294956228 (age 19.430s)
  hex dump (first 32 bytes):
    00 69 6c 65 20 72 65 61 64 00 6e 65 74 3a 5b 34  .ile read.net:[4
    30 32 36 35 33 33 30 39 37 5d 00 00 00 00 00 00  026533097]......
  backtrace:
    [<0000000036bac473>] kmemleak_alloc_recursive /./include/linux/kmemleak.h:43 [inline]
    [<0000000036bac473>] slab_post_alloc_hook /mm/slab.h:522 [inline]
    [<0000000036bac473>] slab_alloc /mm/slab.c:3319 [inline]
    [<0000000036bac473>] __do_kmalloc /mm/slab.c:3653 [inline]
    [<0000000036bac473>] __kmalloc_track_caller+0x169/0x2d0 /mm/slab.c:3670
    [<000000000cd39d07>] kmemdup+0x27/0x60 /mm/util.c:120
    [<000000008e57e5fc>] kmemdup /./include/linux/string.h:432 [inline]
    [<000000008e57e5fc>] llcp_sock_bind+0x1b3/0x230 /net/nfc/llcp_sock.c:107
    [<000000009cb0b5d3>] __sys_bind+0x11c/0x140 /net/socket.c:1647
    [<00000000492c3bbc>] __do_sys_bind /net/socket.c:1658 [inline]
    [<00000000492c3bbc>] __se_sys_bind /net/socket.c:1656 [inline]
    [<00000000492c3bbc>] __x64_sys_bind+0x1e/0x30 /net/socket.c:1656
    [<0000000008704b2a>] do_syscall_64+0x76/0x1a0 /arch/x86/entry/common.c:296
    [<000000009f4c57a4>] entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: 30cc4587659e ("NFC: Move LLCP code to the NFC top level diirectory")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: Unpublish sk from sk_reuseport_cb before call_rcu

[ Upstream commit 8c7138b33e5c690c308b2a7085f6313fdcb3f616 ]

The "reuse->sock[]" array is shared by multiple sockets.  The going away
sk must unpublish itself from "reuse->sock[]" before making call_rcu()
call.  However, this unpublish-action is currently done after a grace
period and it may cause use-after-free.

The fix is to move reuseport_detach_sock() to sk_destruct().
Due to the above reason, any socket with sk_reuseport_cb has
to go through the rcu grace period before freeing it.

It is a rather old bug (~3 yrs).  The Fixes tag is not necessary
the right commit but it is the one that introduced the SOCK_RCU_FREE
logic and this fix is depending on it.

Fixes: a4298e4522d6 ("net: add SOCK_RCU_FREE socket flag")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: qlogic: Fix memory leak in ql_alloc_large_buffers

[ Upstream commit 1acb8f2a7a9f10543868ddd737e37424d5c36cf4 ]

In ql_alloc_large_buffers, a new skb is allocated via netdev_alloc_skb.
This skb should be released if pci_dma_mapping_error fails.

Fixes: 0f8ab89e825f ("qla3xxx: Check return code from pci_map_single() in ql_release_to_lrg_buf_free_list(), ql_populate_free_queue(), ql_alloc_large_buffers(), and ql3xxx_send()")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ipv4: avoid mixed n_redirects and rate_tokens usage

[ Upstream commit b406472b5ad79ede8d10077f0c8f05505ace8b6d ]

Since commit c09551c6ff7f ("net: ipv4: use a dedicated counter
for icmp_v4 redirect packets") we use 'n_redirects' to account
for redirect packets, but we still use 'rate_tokens' to compute
the redirect packets exponential backoff.

If the device sent to the relevant peer any ICMP error packet
after sending a redirect, it will also update 'rate_token' according
to the leaking bucket schema; typically 'rate_token' will raise
above BITS_PER_LONG and the redirect packets backoff algorithm
will produce undefined behavior.

Fix the issue using 'n_redirects' to compute the exponential backoff
in ip_rt_send_redirect().

Note that we still clear rate_tokens after a redirect silence period,
to avoid changing an established behaviour.

The root cause predates git history; before the mentioned commit in
the critical scenario, the kernel stopped sending redirects, after
the mentioned commit the behavior more randomic.

Reported-by: Xiumei Mu <xmu@redhat.com>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Fixes: c09551c6ff7f ("net: ipv4: use a dedicated counter for icmp_v4 redirect packets")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv6: drop incoming packets having a v4mapped source address

[ Upstream commit 6af1799aaf3f1bc8defedddfa00df3192445bbf3 ]

This began with a syzbot report. syzkaller was injecting
IPv6 TCP SYN packets having a v4mapped source address.

After an unsuccessful 4-tuple lookup, TCP creates a request
socket (SYN_RECV) and calls reqsk_queue_hash_req()

reqsk_queue_hash_req() calls sk_ehashfn(sk)

At this point we have AF_INET6 sockets, and the heuristic
used by sk_ehashfn() to either hash the IPv4 or IPv6 addresses
is to use ipv6_addr_v4mapped(&sk->sk_v6_daddr)

For the particular spoofed packet, we end up hashing V4 addresses
which were not initialized by the TCP IPv6 stack, so KMSAN fired
a warning.

I first fixed sk_ehashfn() to test both source and destination addresses,
but then faced various problems, including user-space programs
like packetdrill that had similar assumptions.

Instead of trying to fix the whole ecosystem, it is better
to admit that we have a dual stack behavior, and that we
can not build linux kernels without V4 stack anyway.

The dual stack API automatically forces the traffic to be IPv4
if v4mapped addresses are used at bind() or connect(), so it makes
no sense to allow IPv6 traffic to use the same v4mapped class.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hso: fix NULL-deref on tty open

[ Upstream commit 8353da9fa69722b54cba82b2ec740afd3d438748 ]

Fix NULL-pointer dereference on tty open due to a failure to handle a
missing interrupt-in endpoint when probing modem ports:

BUG: kernel NULL pointer dereference, address: 0000000000000006
...
RIP: 0010:tiocmget_submit_urb+0x1c/0xe0 [hso]
...
Call Trace:
hso_start_serial_device+0xdc/0x140 [hso]
hso_serial_open+0x118/0x1b0 [hso]
tty_open+0xf1/0x490

Fixes: 542f54823614 ("tty: Modem functions for the HSO driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cxgb4:Fix out-of-bounds MSI-X info array access

[ Upstream commit 6b517374f4ea5a3c6e307e1219ec5f35d42e6d00 ]

When fetching free MSI-X vectors for ULDs, check for the error code
before accessing MSI-X info array. Otherwise, an out-of-bounds access is
attempted, which results in kernel panic.

Fixes: 94cdb8bb993a ("cxgb4: Add support for dynamic allocation of resources for ULD")
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ANDROID: binder: synchronize_rcu() when using POLLFREE.

commit 5eeb2ca02a2f6084fc57ae5c244a38baab07033a upstream.

To prevent races with ep_remove_waitqueue() removing the
waitqueue at the same time.

Reported-by: syzbot+a2a3c4909716e271487e@syzkaller.appspotmail.com
Signed-off-by: Martijn Coenen <maco@android.com>
Cc: stable <stable@vger.kernel.org> # 4.14+
Signed-off-by: Mattias Nissler <mnissler@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ANDROID: binder: remove waitqueue when thread exits.

commit f5cb779ba16334b45ba8946d6bfa6d9834d1527f upstream.

binder_poll() passes the thread->wait waitqueue that
can be slept on for work. When a thread that uses
epoll explicitly exits using BINDER_THREAD_EXIT,
the waitqueue is freed, but it is never removed
from the corresponding epoll data structure. When
the process subsequently exits, the epoll cleanup
code tries to access the waitlist, which results in
a use-after-free.

Prevent this by using POLLFREE when the thread exits.

Signed-off-by: Martijn Coenen <maco@android.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: stable <stable@vger.kernel.org> # 4.14
[backport BINDER_LOOPER_STATE_POLL logic as well]
Signed-off-by: Mattias Nissler <mnissler@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kmemleak: increase DEBUG_KMEMLEAK_EARLY_LOG_SIZE default to 16K

[ Upstream commit b751c52bb587ae66f773b15204ef7a147467f4c7 ]

The current default value (400) is too low on many systems (e.g.  some
ARM64 platform takes up 1000+ entries).

syzbot uses 16000 as default value, and has proved to be enough on beefy
configurations, so let's pick that value.

This consumes more RAM on boot (each entry is 160 bytes, so in total
~2.5MB of RAM), but the memory would later be freed (early_log is
__initdata).

Link: http://lkml.kernel.org/r/20190730154027.101525-1-drinkcat@chromium.org
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Suggested-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Uladzislau Rezki <urezki@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ocfs2: wait for recovering done after direct unlock request

[ Upstream commit 0a3775e4f883912944481cf2ef36eb6383a9cc74 ]

There is a scenario causing ocfs2 umount hang when multiple hosts are
rebooting at the same time.

NODE1                           NODE2               NODE3
send unlock requset to NODE2
                                dies
                                                    become recovery master
                                                    recover NODE2
find NODE2 dead
mark resource RECOVERING
directly remove lock from grant list
calculate usage but RECOVERING marked
**miss the window of purging
clear RECOVERING

To reproduce this issue, crash a host and then umount ocfs2
from another node.

To solve this, just let unlock progress wait for recovery done.

Link: http://lkml.kernel.org/r/1550124866-20367-1-git-send-email-gechangwei@live.cn
Signed-off-by: Changwei Ge <gechangwei@live.cn>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hypfs: Fix error number left in struct pointer member

[ Upstream commit b54c64f7adeb241423cd46598f458b5486b0375e ]

In hypfs_fill_super(), if hypfs_create_update_file() fails,
sbi->update_file is left holding an error number.  This is passed to
hypfs_kill_super() which doesn't check for this.

Fix this by not setting sbi->update_value until after we've checked for
error.

Fixes: 24bbb1faf3f0 ("[PATCH] s390_hypfs filesystem")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
cc: Heiko Carstens <heiko.carstens@de.ibm.com>
cc: linux-s390@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fat: work around race with userspace's read via blockdev while mounting

[ Upstream commit 07bfa4415ab607e459b69bd86aa7e7602ce10b4f ]

If userspace reads the buffer via blockdev while mounting,
sb_getblk()+modify can race with buffer read via blockdev.

For example,

            FS                               userspace
    bh = sb_getblk()
    modify bh->b_data
                                  read
    ll_rw_block(bh)
      fill bh->b_data by on-disk data
      /* lost modified data by FS */
      set_buffer_uptodate(bh)
    set_buffer_uptodate(bh)

Userspace should not use the blockdev while mounting though, the udev
seems to be already doing this.  Although I think the udev should try to
avoid this, workaround the race by small overhead.

Link: http://lkml.kernel.org/r/87pnk7l3sw.fsf_-_@mail.parknet.co.jp
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Reported-by: Jan Stancek <jstancek@redhat.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: 8903/1: ensure that usable memory in bank 0 starts from a PMD-aligned address

[ Upstream commit 00d2ec1e6bd82c0538e6dd3e4a4040de93ba4fef ]

The calculation of memblock_limit in adjust_lowmem_bounds() assumes that
bank 0 starts from a PMD-aligned address. However, the beginning of the
first bank may be NOMAP memory and the start of usable memory
will be not aligned to PMD boundary. In such case the memblock_limit will
be set to the end of the NOMAP region, which will prevent any memblock
allocations.

Mark the region between the end of the NOMAP area and the next PMD-aligned
address as NOMAP as well, so that the usable memory will start at
PMD-aligned address.

Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

security: smack: Fix possible null-pointer dereferences in smack_socket_sock_rcv_skb()

[ Upstream commit 3f4287e7d98a2954f20bf96c567fdffcd2b63eb9 ]

In smack_socket_sock_rcv_skb(), there is an if statement
on line 3920 to check whether skb is NULL:
    if (skb && skb->secmark != 0)

This check indicates skb can be NULL in some cases.

But on lines 3931 and 3932, skb is used:
    ad.a.u.net->netif = skb->skb_iif;
    ipv6_skb_to_auditdata(skb, &ad.a, NULL);

Thus, possible null-pointer dereferences may occur when skb is NULL.

To fix these possible bugs, an if statement is added to check skb.

These bugs are found by a static analysis tool STCheck written by us.

Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

HID: apple: Fix stuck function keys when using FN

[ Upstream commit aec256d0ecd561036f188dbc8fa7924c47a9edfd ]

This fixes an issue in which key down events for function keys would be
repeatedly emitted even after the user has raised the physical key. For
example, the driver fails to emit the F5 key up event when going through
the following steps:
- fnmode=1: hold FN, hold F5, release FN, release F5
- fnmode=2: hold F5, hold FN, release F5, release FN

The repeated F5 key down events can be easily verified using xev.

Signed-off-by: Joao Moreno <mail@joaomoreno.com>
Co-developed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: 8898/1: mm: Don't treat faults reported from cache maintenance as writes

[ Upstream commit 834020366da9ab3fb87d1eb9a3160eb22dbed63a ]

Translation faults arising from cache maintenance instructions are
rather unhelpfully reported with an FSR value where the WnR field is set
to 1, indicating that the faulting access was a write. Since cache
maintenance instructions on 32-bit ARM do not require any particular
permissions, this can cause our private 'cacheflush' system call to fail
spuriously if a translation fault is generated due to page aging when
targetting a read-only VMA.

In this situation, we will return -EFAULT to userspace, although this is
unfortunately suppressed by the popular '__builtin___clear_cache()'
intrinsic provided by GCC, which returns void.

Although it's tempting to write this off as a userspace issue, we can
actually do a little bit better on CPUs that support LPAE, even if the
short-descriptor format is in use. On these CPUs, cache maintenance
faults additionally set the CM field in the FSR, which we can use to
suppress the write permission checks in the page fault handler and
succeed in performing cache maintenance to read-only areas even in the
presence of a translation fault.

Reported-by: Orion Hodson <oth@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: tegra: Fix OF node reference leak

[ Upstream commit 9e38e690ace3e7a22a81fc02652fc101efb340cf ]

Each iteration of for_each_child_of_node() executes of_node_put() on the
previous node, but in some return paths in the middle of the loop
of_node_put() is missing thus causing a reference leak.

Hence stash these mid-loop return values in a variable 'err' and add a
new label err_node_put which executes of_node_put() on the previous node
and returns 'err' on failure.

Change mid-loop return statements to point to jump to this label to
fix the reference leak.

Issue found with Coccinelle.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
[lorenzo.pieralisi@arm.com: rewrote commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mfd: intel-lpss: Remove D3cold delay

[ Upstream commit 76380a607ba0b28627c9b4b55cd47a079a59624b ]

Goodix touchpad may drop its first couple input events when
i2c-designware-platdrv and intel-lpss it connects to took too long to
runtime resume from runtime suspended state.

This issue happens becuase the touchpad has a rather small buffer to
store up to 13 input events, so if the host doesn't read those events in
time (i.e. runtime resume takes too long), events are dropped from the
touchpad's buffer.

The bottleneck is D3cold delay it waits when transitioning from D3cold
to D0, hence remove the delay to make the resume faster. I've tested
some systems with intel-lpss and haven't seen any regression.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202683
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

MIPS: tlbex: Explicitly cast _PAGE_NO_EXEC to a boolean

[ Upstream commit c59ae0a1055127dd3828a88e111a0db59b254104 ]

clang warns:

arch/mips/mm/tlbex.c:634:19: error: use of logical '&&' with constant
operand [-Werror,-Wconstant-logical-operand]
        if (cpu_has_rixi && _PAGE_NO_EXEC) {
                         ^  ~~~~~~~~~~~~~
arch/mips/mm/tlbex.c:634:19: note: use '&' for a bitwise operation
        if (cpu_has_rixi && _PAGE_NO_EXEC) {
                         ^~
                         &
arch/mips/mm/tlbex.c:634:19: note: remove constant to silence this
warning
        if (cpu_has_rixi && _PAGE_NO_EXEC) {
                        ~^~~~~~~~~~~~~~~~
1 error generated.

Explicitly cast this value to a boolean so that clang understands we
intend for this to be a non-zero value.

Fixes: 00bf1c691d08 ("MIPS: tlbex: Avoid placing software PTE bits in Entry* PFN fields")
Link: https://github.com/ClangBuiltLinux/linux/issues/609
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: clang-built-linux@googlegroups.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: core: Reduce memory required for SCSI logging

[ Upstream commit dccc96abfb21dc19d69e707c38c8ba439bba7160 ]

The data structure used for log messages is so large that it can cause a
boot failure. Since allocations from that data structure can fail anyway,
use kmalloc() / kfree() instead of that data structure.

See also https://bugzilla.kernel.org/show_bug.cgi?id=204119.
See also commit ded85c193a39 ("scsi: Implement per-cpu logging buffer") # v4.0.

Reported-by: Jan Palus <jpalus@fastmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Jan Palus <jpalus@fastmail.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: at91: select parent if main oscillator or bypass is enabled

[ Upstream commit 69a6bcde7fd3fe6f3268ce26f31d9d9378384c98 ]

Selecting the right parent for the main clock is done using only
main oscillator enabled bit.
In case we have this oscillator bypassed by an external signal (no driving
on the XOUT line), we still use external clock, but with BYPASS bit set.
So, in this case we must select the same parent as before.
Create a macro that will select the right parent considering both bits from
the MOR register.
Use this macro when looking for the right parent.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lkml.kernel.org/r/1568042692-11784-2-git-send-email-eugen.hristev@microchip.com
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: fix unreachable code issue with cmpxchg

[ Upstream commit 920fdab7b3ce98c14c840261e364f490f3679a62 ]

On arm64 build with clang, sometimes the __cmpxchg_mb is not inlined
when CONFIG_OPTIMIZE_INLINING is set.
Clang then fails a compile-time assertion, because it cannot tell at
compile time what the size of the argument is:

mm/memcontrol.o: In function `__cmpxchg_mb':
memcontrol.c:(.text+0x1a4c): undefined reference to `__compiletime_assert_175'
memcontrol.c:(.text+0x1a4c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `__compiletime_assert_175'

Mark all of the cmpxchg() style functions as __always_inline to
ensure that the compiler can see the result.

Acked-by: Nick Desaulniers <ndesaulniers@google.com>
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/648
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Tested-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/pseries: correctly track irq state in default idle

[ Upstream commit 92c94dfb69e350471473fd3075c74bc68150879e ]

prep_irq_for_idle() is intended to be called before entering
H_CEDE (and it is used by the pseries cpuidle driver). However the
default pseries idle routine does not call it, leading to mismanaged
lazy irq state when the cpuidle driver isn't in use. Manifestations of
this include:

* Dropped IPIs in the time immediately after a cpu comes
  online (before it has installed the cpuidle handler), making the
  online operation block indefinitely waiting for the new cpu to
  respond.

* Hitting this WARN_ON in arch_local_irq_restore():
/*
 * We should already be hard disabled here. We had bugs
 * where that wasn't the case so let's dbl check it and
 * warn if we are wrong. Only do that when IRQ tracing
 * is enabled as mfmsr() can be costly.
 */
if (WARN_ON_ONCE(mfmsr() & MSR_EE))
__hard_irq_disable();

Call prep_irq_for_idle() from pseries_lpar_idle() and honor its
result.

Fixes: 363edbe2614a ("powerpc: Default arch idle could cede processor on pseries")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190910225244.25056-1-nathanl@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/64s/exception: machine check use correct cfar for late handler

[ Upstream commit 0b66370c61fcf5fcc1d6901013e110284da6e2bb ]

Bare metal machine checks run an "early" handler in real mode before
running the main handler which reports the event.

The main handler runs exactly as a normal interrupt handler, after the
"windup" which sets registers back as they were at interrupt entry.
CFAR does not get restored by the windup code, so that will be wrong
when the handler is run.

Restore the CFAR to the saved value before running the late handler.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-8-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu/si: fix ASIC tests

[ Upstream commit 77efe48a729588527afb4d5811b9e0acb29f5e51 ]

Comparing adev->family with CHIP constants is not correct.
adev->family can only be compared with AMDGPU_FAMILY constants and
adev->asic_type is the struct member to compare with CHIP constants.
They are separate identification spaces.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 62a37553414a ("drm/amdgpu: add si implementation v10")
Cc: Ken Wang <Qingqing.Wang@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

vfio_pci: Restore original state on release

[ Upstream commit 92c8026854c25093946e0d7fe536fd9eac440f06 ]

vfio_pci_enable() saves the device's initial configuration information
with the intent that it is restored in vfio_pci_disable().  However,
the commit referenced in Fixes: below replaced the call to
__pci_reset_function_locked(), which is not wrapped in a state save
and restore, with pci_try_reset_function(), which overwrites the
restored device state with the current state before applying it to the
device.  Reinstate use of __pci_reset_function_locked() to return to
the desired behavior.

Fixes: 890ed578df82 ("vfio-pci: Use pci "try" reset interface")
Signed-off-by: hexin <hexin15@baidu.com>
Signed-off-by: Liu Qi <liuqi16@baidu.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pinctrl: tegra: Fix write barrier placement in pmx_writel

[ Upstream commit c2cf351eba2ff6002ce8eb178452219d2521e38e ]

pmx_writel uses writel which inserts write barrier before the
register write.

This patch has fix to replace writel with writel_relaxed followed
by a readback and memory barrier to ensure write operation is
completed for successful pinctrl change.

Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1565984527-5272-2-git-send-email-skomatineni@nvidia.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/pseries/mobility: use cond_resched when updating device tree

[ Upstream commit ccfb5bd71d3d1228090a8633800ae7cdf42a94ac ]

After a partition migration, pseries_devicetree_update() processes
changes to the device tree communicated from the platform to
Linux. This is a relatively heavyweight operation, with multiple
device tree searches, memory allocations, and conversations with
partition firmware.

There's a few levels of nested loops which are bounded only by
decisions made by the platform, outside of Linux's control, and indeed
we have seen RCU stalls on large systems while executing this call
graph. Use cond_resched() in these loops so that the cpu is yielded
when needed.

Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802192926.19277-4-nathanl@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/futex: Fix warning: 'oldval' may be used uninitialized in this function

[ Upstream commit 38a0d0cdb46d3f91534e5b9839ec2d67be14c59d ]

We see warnings such as:
  kernel/futex.c: In function 'do_futex':
  kernel/futex.c:1676:17: warning: 'oldval' may be used uninitialized in this function [-Wmaybe-uninitialized]
     return oldval == cmparg;
                   ^
  kernel/futex.c:1651:6: note: 'oldval' was declared here
    int oldval, ret;
        ^

This is because arch_futex_atomic_op_inuser() only sets *oval if ret
is 0 and GCC doesn't see that it will only use it when ret is 0.

Anyway, the non-zero ret path is an error path that won't suffer from
setting *oval, and as *oval is a local var in futex_atomic_op_inuser()
it will have no impact.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: reword change log slightly]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/86b72f0c134367b214910b27b9a6dd3321af93bb.1565774657.git.christophe.leroy@c-s.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/rtas: use device model APIs and serialization during LPM

[ Upstream commit a6717c01ddc259f6f73364779df058e2c67309f8 ]

The LPAR migration implementation and userspace-initiated cpu hotplug
can interleave their executions like so:

1. Set cpu 7 offline via sysfs.

2. Begin a partition migration, whose implementation requires the OS
   to ensure all present cpus are online; cpu 7 is onlined:

     rtas_ibm_suspend_me -> rtas_online_cpus_mask -> cpu_up

   This sets cpu 7 online in all respects except for the cpu's
   corresponding struct device; dev->offline remains true.

3. Set cpu 7 online via sysfs. _cpu_up() determines that cpu 7 is
   already online and returns success. The driver core (device_online)
   sets dev->offline = false.

4. The migration completes and restores cpu 7 to offline state:

     rtas_ibm_suspend_me -> rtas_offline_cpus_mask -> cpu_down

This leaves cpu7 in a state where the driver core considers the cpu
device online, but in all other respects it is offline and
unused. Attempts to online the cpu via sysfs appear to succeed but the
driver core actually does not pass the request to the lower-level
cpuhp support code. This makes the cpu unusable until the cpu device
is manually set offline and then online again via sysfs.

Instead of directly calling cpu_up/cpu_down, the migration code should
use the higher-level device core APIs to maintain consistent state and
serialize operations.

Fixes: 120496ac2d2d ("powerpc: Bring all threads online prior to migration/hibernation")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802192926.19277-2-nathanl@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: sirf: Don't reference clk_init_data after registration

[ Upstream commit af55dadfbce35b4f4c6247244ce3e44b2e242b84 ]

A future patch is going to change semantics of clk_register() so that
clk_hw::init is guaranteed to be NULL after a clk is registered. Avoid
referencing this member here so that we don't run into NULL pointer
exceptions.

Cc: Guo Zeng <Guo.Zeng@csr.com>
Cc: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190731193517.237136-6-sboyd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: qoriq: Fix -Wunused-const-variable

[ Upstream commit a95fb581b144b5e73da382eaedb2e32027610597 ]

drivers/clk/clk-qoriq.c:138:38: warning: unused variable
'p5020_cmux_grp1' [-Wunused-const-variable] static const struct
clockgen_muxinfo p5020_cmux_grp1

drivers/clk/clk-qoriq.c:146:38: warning: unused variable
'p5020_cmux_grp2' [-Wunused-const-variable] static const struct
clockgen_muxinfo p5020_cmux_grp2

In the definition of the p5020 chip, the p2041 chip's info was used
instead.  The p5020 and p2041 chips have different info. This is most
likely a typo.

Link: https://github.com/ClangBuiltLinux/linux/issues/525
Cc: clang-built-linux@googlegroups.com
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Link: https://lkml.kernel.org/r/20190627220642.78575-1-nhuck@google.com
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ipmi_si: Only schedule continuously in the thread in maintenance mode

[ Upstream commit 340ff31ab00bca5c15915e70ad9ada3030c98cf8 ]

ipmi_thread() uses back-to-back schedule() to poll for command
completion which, on some machines, can push up CPU consumption and
heavily tax the scheduler locks leading to noticeable overall
performance degradation.

This was originally added so firmware updates through IPMI would
complete in a timely manner.  But we can't kill the scheduler
locks for that one use case.

Instead, only run schedule() continuously in maintenance mode,
where firmware updates should run.

Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpu: drm: radeon: Fix a possible null-pointer dereference in radeon_connector_set_property()

[ Upstream commit f3eb9b8f67bc28783eddc142ad805ebdc53d6339 ]

In radeon_connector_set_property(), there is an if statement on line 743
to check whether connector->encoder is NULL:
    if (connector->encoder)

When connector->encoder is NULL, it is used on line 755:
    if (connector->encoder->crtc)

Thus, a possible null-pointer dereference may occur.

To fix this bug, connector->encoder is checked before being used.

This bug is found by a static analysis tool STCheck written by us.

Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/radeon: Fix EEH during kexec

[ Upstream commit 6f7fe9a93e6c09bf988c5059403f5f88e17e21e6 ]

During kexec some adapters hit an EEH since they are not properly
shut down in the radeon_pci_shutdown() function. Adding
radeon_suspend_kms() fixes this issue.

Signed-off-by: KyleMahlkuch <kmahlkuc@linux.vnet.ibm.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

video: ssd1307fb: Start page range at page_offset

[ Upstream commit dd9782834dd9dde3624ff1acea8859f3d3e792d4 ]

The page_offset was only applied to the end of the page range. This caused
the display updates to cause a scrolling effect on the display because the
amount of data written to the display did not match the range display
expected.

Fixes: 301bc0675b67 ("video: ssd1307fb: Make use of horizontal addressing mode")
Signed-off-by: Marko Kohtala <marko.kohtala@okoko.fi>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190618074111.9309-4-marko.kohtala@okoko.fi
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/bridge: tc358767: Increase AUX transfer length limit

[ Upstream commit e0655feaec62d5139b6b13a7b1bbb1ab8f1c2d83 ]

According to the datasheet tc358767 can transfer up to 16 bytes via
its AUX channel, so the artificial limit of 8 appears to be too
low. However only up to 15-bytes seem to be actually supported and
trying to use 16-byte transfers results in transfers failing
sporadically (with bogus status in case of I2C transfers), so limit it
to 15.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-9-andrew.smirnov@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

Linux 4.9.195

Btrfs: fix race setting up and completing qgroup rescan workers

[ Upstream commit 13fc1d271a2e3ab8a02071e711add01fab9271f6 ]

There is a race between setting up a qgroup rescan worker and completing
a qgroup rescan worker that can lead to callers of the qgroup rescan wait
ioctl to either not wait for the rescan worker to complete or to hang
forever due to missing wake ups. The following diagram shows a sequence
of steps that illustrates the race.

        CPU 1                                                         CPU 2                                  CPU 3

 btrfs_ioctl_quota_rescan()
  btrfs_qgroup_rescan()
   qgroup_rescan_init()
    mutex_lock(&fs_info->qgroup_rescan_lock)
    spin_lock(&fs_info->qgroup_lock)

    fs_info->qgroup_flags |=
      BTRFS_QGROUP_STATUS_FLAG_RESCAN

    init_completion(
      &fs_info->qgroup_rescan_completion)

    fs_info->qgroup_rescan_running = true

    mutex_unlock(&fs_info->qgroup_rescan_lock)
    spin_unlock(&fs_info->qgroup_lock)

    btrfs_init_work()
     --> starts the worker

                                                        btrfs_qgroup_rescan_worker()
                                                         mutex_lock(&fs_info->qgroup_rescan_lock)

                                                         fs_info->qgroup_flags &=
                                                           ~BTRFS_QGROUP_STATUS_FLAG_RESCAN

                                                         mutex_unlock(&fs_info->qgroup_rescan_lock)

                                                         starts transaction, updates qgroup status
                                                         item, etc

                                                                                                           btrfs_ioctl_quota_rescan()
                                                                                                            btrfs_qgroup_rescan()
                                                                                                             qgroup_rescan_init()
                                                                                                              mutex_lock(&fs_info->qgroup_rescan_lock)
                                                                                                              spin_lock(&fs_info->qgroup_lock)

                                                                                                              fs_info->qgroup_flags |=
                                                                                                                BTRFS_QGROUP_STATUS_FLAG_RESCAN

                                                                                                              init_completion(
                                                                                                                &fs_info->qgroup_rescan_completion)

                                                                                                              fs_info->qgroup_rescan_running = true

                                                                                                              mutex_unlock(&fs_info->qgroup_rescan_lock)
                                                                                                              spin_unlock(&fs_info->qgroup_lock)

                                                                                                              btrfs_init_work()
                                                                                                               --> starts another worker

                                                         mutex_lock(&fs_info->qgroup_rescan_lock)

                                                         fs_info->qgroup_rescan_running = false

                                                         mutex_unlock(&fs_info->qgroup_rescan_lock)

 complete_all(&fs_info->qgroup_rescan_completion)

Before the rescan worker started by the task at CPU 3 completes, if
another task calls btrfs_ioctl_quota_rescan(), it will get -EINPROGRESS
because the flag BTRFS_QGROUP_STATUS_FLAG_RESCAN is set at
fs_info->qgroup_flags, which is expected and correct behaviour.

However if other task calls btrfs_ioctl_quota_rescan_wait() before the
rescan worker started by the task at CPU 3 completes, it will return
immediately without waiting for the new rescan worker to complete,
because fs_info->qgroup_rescan_running is set to false by CPU 2.

This race is making test case btrfs/171 (from fstests) to fail often:

  btrfs/171 9s ... - output mismatch (see /home/fdmanana/git/hub/xfstests/results//btrfs/171.out.bad)
#      --- tests/btrfs/171.out     2018-09-16 21:30:48.505104287 +0100
#      +++ /home/fdmanana/git/hub/xfstests/results//btrfs/171.out.bad      2019-09-19 02:01:36.938486039 +0100
#      @@ -1,2 +1,3 @@
#       QA output created by 171
#      +ERROR: quota rescan failed: Operation now in progress
#       Silence is golden
#      ...
#      (Run 'diff -u /home/fdmanana/git/hub/xfstests/tests/btrfs/171.out /home/fdmanana/git/hub/xfstests/results//btrfs/171.out.bad'  to see the entire diff)

That is because the test calls the btrfs-progs commands "qgroup quota
rescan -w", "qgroup assign" and "qgroup remove" in a sequence that makes
calls to the rescan start ioctl fail with -EINPROGRESS (note the "btrfs"
commands 'qgroup assign' and 'qgroup remove' often call the rescan start
ioctl after calling the qgroup assign ioctl,
btrfs_ioctl_qgroup_assign()), since previous waits didn't actually wait
for a rescan worker to complete.

Another problem the race can cause is missing wake ups for waiters,
since the call to complete_all() happens outside a critical section and
after clearing the flag BTRFS_QGROUP_STATUS_FLAG_RESCAN. In the sequence
diagram above, if we have a waiter for the first rescan task (executed
by CPU 2), then fs_info->qgroup_rescan_completion.wait is not empty, and
if after the rescan worker clears BTRFS_QGROUP_STATUS_FLAG_RESCAN and
before it calls complete_all() against
fs_info->qgroup_rescan_completion, the task at CPU 3 calls
init_completion() against fs_info->qgroup_rescan_completion which
re-initilizes its wait queue to an empty queue, therefore causing the
rescan worker at CPU 2 to call complete_all() against an empty queue,
never waking up the task waiting for that rescan worker.

Fix this by clearing BTRFS_QGROUP_STATUS_FLAG_RESCAN and setting
fs_info->qgroup_rescan_running to false in the same critical section,
delimited by the mutex fs_info->qgroup_rescan_lock, as well as doing the
call to complete_all() in that same critical section. This gives the
protection needed to avoid rescan wait ioctl callers not waiting for a
running rescan worker and the lost wake ups problem, since setting that
rescan flag and boolean as well as initializing the wait queue is done
already in a critical section delimited by that mutex (at
qgroup_rescan_init()).

Fixes: 57254b6ebce4ce ("Btrfs: add ioctl to wait for qgroup rescan completion")
Fixes: d2c609b834d62f ("btrfs: properly track when rescan worker is running")
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

btrfs: qgroup: Drop quota_root and fs_info parameters from update_qgroup_status_item

[ Upstream commit 2e980acdd829742966c6a7e565ef3382c0717295 ]

They can be fetched from the transaction handle.

Signed-off-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

CIFS: Fix oplock handling for SMB 2.1+ protocols

commit a016e2794fc3a245a91946038dd8f34d65e53cc3 upstream.

There may be situations when a server negotiates SMB 2.1
protocol version or higher but responds to a CREATE request
with an oplock rather than a lease.

Currently the client doesn't handle such a case correctly:
when another CREATE comes in the server sends an oplock
break to the initial CREATE and the client doesn't send
an ack back due to a wrong caching level being set (READ
instead of RWH). Missing an oplock break ack makes the
server wait until the break times out which dramatically
increases the latency of the second CREATE.

Fix this by properly detecting oplocks when using SMB 2.1
protocol version and higher.

Cc: <stable@vger.kernel.org>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

CIFS: fix max ea value size

commit 63d37fb4ce5ae7bf1e58f906d1bf25f036fe79b2 upstream.

It should not be larger then the slab max buf size. If user
specifies a larger size, it passes this check and goes
straightly to SMB2_set_info_init performing an insecure memcpy.

Signed-off-by: Murphy Zhou <jencce.kernel@gmail.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i2c: riic: Clear NACK in tend isr

commit a71e2ac1f32097fbb2beab098687a7a95c84543e upstream.

The NACKF flag should be cleared in INTRIICNAKI interrupt processing as
description in HW manual.

This issue shows up quickly when PREEMPT_RT is applied and a device is
probed that is not plugged in (like a touchscreen controller). The result
is endless interrupts that halt system boot.

Fixes: 310c18a41450 ("i2c: riic: add driver")
Cc: stable@vger.kernel.org
Reported-by: Chien Nguyen <chien.nguyen.eb@rvc.renesas.com>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hwrng: core - don't wait on add_early_randomness()

commit 78887832e76541f77169a24ac238fccb51059b63 upstream.

add_early_randomness() is called by hwrng_register() when the
hardware is added. If this hardware and its module are present
at boot, and if there is no data available the boot hangs until
data are available and can't be interrupted.

For instance, in the case of virtio-rng, in some cases the host can be
not able to provide enough entropy for all the guests.

We can have two easy ways to reproduce the problem but they rely on
misconfiguration of the hypervisor or the egd daemon:

- if virtio-rng device is configured to connect to the egd daemon of the
host but when the virtio-rng driver asks for data the daemon is not
connected,

- if virtio-rng device is configured to connect to the egd daemon of the
host but the egd daemon doesn't provide data.

The guest kernel will hang at boot until the virtio-rng driver provides
enough data.

To avoid that, call rng_get_data() in non-blocking mode (wait=0)
from add_early_randomness().

Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Fixes: d9e797261933 ("hwrng: add randomness to system from rng...")
Cc: <stable@vger.kernel.org>
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

quota: fix wrong condition in is_quota_modification()

commit 6565c182094f69e4ffdece337d395eb7ec760efc upstream.

Quoted from
commit 3da40c7b0898 ("ext4: only call ext4_truncate when size <= isize")

" At LSF we decided that if we truncate up from isize we shouldn't trim
  fallocated blocks that were fallocated with KEEP_SIZE and are past the
 new i_size.  This patch fixes ext4 to do this. "

And generic/092 of fstest have covered this case for long time, however
is_quota_modification() didn't adjust based on that rule, so that in
below condition, we will lose to quota block change:
- fallocate blocks beyond EOF
- remount
- truncate(file_path, file_size)

Fix it.

Link: https://lore.kernel.org/r/20190911093650.35329-1-yuchao0@huawei.com
Fixes: 3da40c7b0898 ("ext4: only call ext4_truncate when size <= isize")
CC: stable@vger.kernel.org
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: fix punch hole for inline_data file systems

commit c1e8220bd316d8ae8e524df39534b8a412a45d5e upstream.

If a program attempts to punch a hole on an inline data file, we need
to convert it to a normal file first.

This was detected using ext4/032 using the adv configuration.  Simple
reproducer:

mke2fs -Fq -t ext4 -O inline_data /dev/vdc
mount /vdc
echo "" > /vdc/testfile
xfs_io -c 'truncate 33554432' /vdc/testfile
xfs_io -c 'fpunch 0 1048576' /vdc/testfile
umount /vdc
e2fsck -fy /dev/vdc

Cc: stable@vger.kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: fix warning inside ext4_convert_unwritten_extents_endio

commit e3d550c2c4f2f3dba469bc3c4b83d9332b4e99e1 upstream.

Really enable warning when CONFIG_EXT4_DEBUG is set and fix missing
first argument.  This was introduced in commit ff95ec22cd7f ("ext4:
add warning to ext4_convert_unwritten_extents_endio") and splitting
extents inside endio would trigger it.

Fixes: ff95ec22cd7f ("ext4: add warning to ext4_convert_unwritten_extents_endio")
Signed-off-by: Rakesh Pandit <rakesh@tuxera.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>