mac80211: shorten the IBSS debug messages

[ Upstream commit c6e57b3896fc76299913b8cfd82d853bee8a2c84 ]

When tracing is enabled, all the debug messages are recorded and must
not exceed MAX_MSG_LEN (100) columns. Longer debug messages grant the
user with:

WARNING: CPU: 3 PID: 32642 at /tmp/wifi-core-20180806094828/src/iwlwifi-stack-dev/net/mac80211/./trace_msg.h:32 trace_event_raw_event_mac80211_msg_event+0xab/0xc0 [mac80211]
Workqueue: phy1 ieee80211_iface_work [mac80211]
 RIP: 0010:trace_event_raw_event_mac80211_msg_event+0xab/0xc0 [mac80211]
 Call Trace:
  __sdata_dbg+0xbd/0x120 [mac80211]
  ieee80211_ibss_rx_queued_mgmt+0x15f/0x510 [mac80211]
  ieee80211_iface_work+0x21d/0x320 [mac80211]

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: don't Tx a deauth frame if the AP forbade Tx

[ Upstream commit 6c18b27d6e5c6a7206364eae2b47bc8d8b2fa68f ]

If the driver fails to properly prepare for the channel
switch, mac80211 will disconnect. If the CSA IE had mode
set to 1, it means that the clients are not allowed to send
any Tx on the current channel, and that includes the
deauthentication frame.

Make sure that we don't send the deauthentication frame in
this case.

In iwlwifi, this caused a failure to flush queues since the
firmware already closed the queues after having parsed the
CSA IE. Then mac80211 would wait until the deauthentication
frame would go out (drv_flush(drop=false)) and that would
never happen.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: Fix station bandwidth setting after channel switch

[ Upstream commit 0007e94355fdb71a1cf5dba0754155cba08f0666 ]

When performing a channel switch flow for a managed interface, the
flow did not update the bandwidth of the AP station and the rate
scale algorithm. In case of a channel width downgrade, this would
result with the rate scale algorithm using a bandwidth that does not
match the interface channel configuration.

Fix this by updating the AP station bandwidth and rate scaling algorithm
before the actual channel change in case of a bandwidth downgrade, or
after the actual channel change in case of a bandwidth upgrade.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: fix a race between restart and CSA flows

[ Upstream commit f3ffb6c3a28963657eb8b02a795d75f2ebbd5ef4 ]

We hit a problem with iwlwifi that was caused by a bug in
mac80211. A bug in iwlwifi caused the firwmare to crash in
certain cases in channel switch. Because of that bug,
drv_pre_channel_switch would fail and trigger the restart
flow.
Now we had the hw restart worker which runs on the system's
workqueue and the csa_connection_drop_work worker that runs
on mac80211's workqueue that can run together. This is
obviously problematic since the restart work wants to
reconfigure the connection, while the csa_connection_drop_work
worker does the exact opposite: it tries to disconnect.

Fix this by cancelling the csa_connection_drop_work worker
in the restart worker.

Note that this can sound racy: we could have:

driver   iface_work   CSA_work   restart_work
+++++++++++++++++++++++++++++++++++++++++++++
              |
 <--drv_cs ---|
<FW CRASH!>
-CS FAILED-->
              |                       |
              |                 cancel_work(CSA)
           schedule                   |
           CSA work                   |
                         |            |
                        Race between those 2

But this is not possible because we flush the workqueue
in the restart worker before we cancel the CSA worker.
That would be bullet proof if we could guarantee that
we schedule the CSA worker only from the iface_work
which runs on the workqueue (and not on the system's
workqueue), but unfortunately we do have an instance
in which we schedule the CSA work outside the context
of the workqueue (ieee80211_chswitch_done).

Note also that we should probably cancel other workers
like beacon_connection_loss_work and possibly others
for different types of interfaces, at the very least,
IBSS should suffer from the exact same problem, but for
now, do the minimum to fix the actual bug that was actually
experienced and reproduced.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cfg80211: fix a type issue in ieee80211_chandef_to_operating_class()

[ Upstream commit 8442938c3a2177ba16043b3a935f2c78266ad399 ]

The "chandef->center_freq1" variable is a u32 but "freq" is a u16 so we
are truncating away the high bits.  I noticed this bug because in commit
9cf0a0b4b64a ("cfg80211: Add support for 60GHz band channels 5 and 6")
we made "freq <= 56160 + 2160 * 6" a valid requency when before it was
only "freq <= 56160 + 2160 * 4" that was valid.  It introduces a static
checker warning:

    net/wireless/util.c:1571 ieee80211_chandef_to_operating_class()
    warn: always true condition '(freq <= 56160 + 2160 * 6) => (0-u16max <= 69120)'

But really we probably shouldn't have been truncating the high bits
away to begin with.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fs/cifs: don't translate SFM_SLASH (U+F026) to backslash

[ Upstream commit c15e3f19a6d5c89b1209dc94b40e568177cb0921 ]

When a Mac client saves an item containing a backslash to a file server
the backslash is represented in the CIFS/SMB protocol as as U+F026.
Before this change, listing a directory containing an item with a
backslash in its name will return that item with the backslash
represented with a true backslash character (U+005C) because
convert_sfm_character mapped U+F026 to U+005C when interpretting the
CIFS/SMB protocol response.  However, attempting to open or stat the
path using a true backslash will result in an error because
convert_to_sfm_char does not map U+005C back to U+F026 causing the
CIFS/SMB request to be made with the backslash represented as U+005C.

This change simply prevents the U+F026 to U+005C conversion from
happenning.  This is analogous to how the code does not do any
translation of UNI_SLASH (U+F000).

Signed-off-by: Jon Kuhn <jkuhn@barracuda.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: cadence: Fix a sleep-in-atomic-context bug in macb_halt_tx()

[ Upstream commit 16fe10cf92783ed9ceb182d6ea2b8adf5e8ec1b8 ]

The kernel module may sleep with holding a spinlock.

The function call paths (from bottom to top) in Linux-4.16 are:

[FUNC] usleep_range
drivers/net/ethernet/cadence/macb_main.c, 648:
usleep_range in macb_halt_tx
drivers/net/ethernet/cadence/macb_main.c, 730:
macb_halt_tx in macb_tx_error_task
drivers/net/ethernet/cadence/macb_main.c, 721:
_raw_spin_lock_irqsave in macb_tx_error_task

To fix this bug, usleep_range() is replaced with udelay().

This bug is found by my static analysis tool DSAC.

Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i2c: uniphier-f: issue STOP only for last message or I2C_M_STOP

[ Upstream commit 4c85609b08c4761eca0a40fd7beb06bc650f252d ]

This driver currently emits a STOP if the next message is not
I2C_MD_RD.  It should not do it because it disturbs the I2C_RDWR
ioctl, where read/write transactions are combined without STOP
between.

Issue STOP only when the message is the last one _or_ flagged with
I2C_M_STOP.

Fixes: 6a62974b667f ("i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i2c: uniphier: issue STOP only for last message or I2C_M_STOP

[ Upstream commit 38f5d8d8cbb2ffa2b54315118185332329ec891c ]

This driver currently emits a STOP if the next message is not
I2C_MD_RD.  It should not do it because it disturbs the I2C_RDWR
ioctl, where read/write transactions are combined without STOP
between.

Issue STOP only when the message is the last one _or_ flagged with
I2C_M_STOP.

Fixes: dd6fd4a32793 ("i2c: uniphier: add UniPhier FIFO-less I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RAID10 BUG_ON in raise_barrier when force is true and conf->barrier is 0

[ Upstream commit 1d0ffd264204eba1861865560f1f7f7a92919384 ]

In raid10 reshape_request it gets max_sectors in read_balance. If the underlayer disks
have bad blocks, the max_sectors is less than last. It will call goto read_more many
times. It calls raise_barrier(conf, sectors_done != 0) every time. In this condition
sectors_done is not 0. So the value passed to the argument force of raise_barrier is
true.

In raise_barrier it checks conf->barrier when force is true. If force is true and
conf->barrier is 0, it panic. In this case reshape_request submits bio to under layer
disks. And in the callback function of the bio it calls lower_barrier. If the bio
finishes before calling raise_barrier again, it can trigger the BUG_ON.

Add one pair of raise_barrier/lower_barrier to fix this bug.

Signed-off-by: Xiao Ni <xni@redhat.com>
Suggested-by: Neil Brown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARC: atomics: unbork atomic_fetch_##op()

[ Upstream commit 3fcbb8260a87efb691d837e8cd24e81f65b3eb70 ]

In 4.19-rc1, Eugeniy reported weird boot and IO errors on ARC HSDK

| INFO: task syslogd:77 blocked for more than 10 seconds.
|       Not tainted 4.19.0-rc1-00007-gf213acea4e88 #40
| "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this
| message.
| syslogd         D    0    77     76 0x00000000
|
| Stack Trace:
|  __switch_to+0x0/0xac
|  __schedule+0x1b2/0x730
|  io_schedule+0x5c/0xc0
|  __lock_page+0x98/0xdc
|  find_lock_entry+0x38/0x100
|  shmem_getpage_gfp.isra.3+0x82/0xbfc
|  shmem_fault+0x46/0x138
|  handle_mm_fault+0x5bc/0x924
|  do_page_fault+0x100/0x2b8
|  ret_from_exception+0x0/0x8

He bisected to 84c6591103db ("locking/atomics,
asm-generic/bitops/lock.h: Rewrite using atomic_fetch_*()")

This commit however only unmasked the real issue introduced by commit
4aef66c8ae9 ("locking/atomic, arch/arc: Fix build") which missed the
retry-if-scond-failed branch in atomic_fetch_##op() macros.

The bisected commit started using atomic_fetch_##op() macros for building
the rest of atomics.

Fixes: 4aef66c8ae9 ("locking/atomic, arch/arc: Fix build")
Reported-by: Eugeniy Paltsev <paltsev@synopsys.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: wrote changelog]
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gpio: Fix crash due to registration race

[ Upstream commit d49b48f088c323dbacae44dfbe56d9c985c8a2a1 ]

gpiochip_add_data_with_key() adds the gpiochip to the gpio_devices list
before of_gpiochip_add() is called, but it's only the latter which sets
the ->of_xlate function pointer.  gpiochip_find() can be called by
someone else between these two actions, and it can find the chip and
call of_gpiochip_match_node_and_xlate() which leads to the following
crash due to a NULL ->of_xlate().

 Unhandled prefetch abort: page domain fault (0x01b) at 0x00000000
 Modules linked in: leds_gpio(+) gpio_generic(+)
 CPU: 0 PID: 830 Comm: insmod Not tainted 4.18.0+ #43
 Hardware name: ARM-Versatile Express
 PC is at   (null)
 LR is at of_gpiochip_match_node_and_xlate+0x2c/0x38
 Process insmod (pid: 830, stack limit = 0x(ptrval))
  (of_gpiochip_match_node_and_xlate) from  (gpiochip_find+0x48/0x84)
  (gpiochip_find) from  (of_get_named_gpiod_flags+0xa8/0x238)
  (of_get_named_gpiod_flags) from  (gpiod_get_from_of_node+0x2c/0xc8)
  (gpiod_get_from_of_node) from  (devm_fwnode_get_index_gpiod_from_child+0xb8/0x144)
  (devm_fwnode_get_index_gpiod_from_child) from  (gpio_led_probe+0x208/0x3c4 [leds_gpio])
  (gpio_led_probe [leds_gpio]) from  (platform_drv_probe+0x48/0x9c)
  (platform_drv_probe) from  (really_probe+0x1d0/0x3d4)
  (really_probe) from  (driver_probe_device+0x78/0x1c0)
  (driver_probe_device) from  (__driver_attach+0x120/0x13c)
  (__driver_attach) from  (bus_for_each_dev+0x68/0xb4)
  (bus_for_each_dev) from  (bus_add_driver+0x1a8/0x268)
  (bus_add_driver) from  (driver_register+0x78/0x10c)
  (driver_register) from  (do_one_initcall+0x54/0x1fc)
  (do_one_initcall) from  (do_init_module+0x64/0x1f4)
  (do_init_module) from  (load_module+0x2198/0x26ac)
  (load_module) from  (sys_finit_module+0xe0/0x110)
  (sys_finit_module) from  (ret_fast_syscall+0x0/0x54)

One way to fix this would be to rework the hairy registration sequence
in gpiochip_add_data_with_key(), but since I'd probably introduce a
couple of new bugs if I attempted that, simply add a check for a
non-NULL of_xlate function pointer in
of_gpiochip_match_node_and_xlate().  This works since the driver looking
for the gpio will simply fail to find the gpio and defer its probe and
be reprobed when the driver which is registering the gpiochip has fully
completed its probe.

Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cfg80211: nl80211_update_ft_ies() to validate NL80211_ATTR_IE

[ Upstream commit 4f0223bfe9c3e62d8f45a85f1ef1b18a8a263ef9 ]

nl80211_update_ft_ies() tried to validate NL80211_ATTR_IE with
is_valid_ie_attr() before dereferencing it, but that helper function
returns true in case of NULL pointer (i.e., attribute not included).
This can result to dereferencing a NULL pointer. Fix that by explicitly
checking that NL80211_ATTR_IE is included.

Fixes: 355199e02b83 ("cfg80211: Extend support for IEEE 802.11r Fast BSS Transition")
Signed-off-by: Arunk Khandavalli <akhandav@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: hns: add netif_carrier_off before change speed and duplex

[ Upstream commit 455c4401fe7a538facaffb35b906ce19f1ece474 ]

If there are packets in hardware when changing the speed
or duplex, it may cause hardware hang up.

This patch adds netif_carrier_off before change speed and
duplex in ethtool_ops.set_link_ksettings, and adds
netif_carrier_on after complete the change.

Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: mesh: fix HWMP sequence numbering to follow standard

[ Upstream commit 1f631c3201fe5491808df143d8fcba81b3197ffd ]

IEEE 802.11-2016 14.10.8.3 HWMP sequence numbering says:
If it is a target mesh STA, it shall update its own HWMP SN to
maximum (current HWMP SN, target HWMP SN in the PREQ element) + 1
immediately before it generates a PREP element in response to a
PREQ element.

Signed-off-by: Yuan-Chi Pang <fu3mo6goo@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gpio: adp5588: Fix sleep-in-atomic-context bug

[ Upstream commit 6537886cdc9a637711fd6da980dbb87c2c87c9aa ]

This fixes:
[BUG] gpio: gpio-adp5588: A possible sleep-in-atomic-context bug
                          in adp5588_gpio_write()
[BUG] gpio: gpio-adp5588: A possible sleep-in-atomic-context bug
                          in adp5588_gpio_direction_input()

Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211_hwsim: correct use of IEEE80211_VHT_CAP_RXSTBC_X

[ Upstream commit d7c863a2f65e48f442379f4ee1846d52e0c5d24d ]

The mac80211_hwsim driver intends to say that it supports up to four
STBC receive streams, but instead it ends up saying something undefined.
The IEEE80211_VHT_CAP_RXSTBC_X macros aren't independent bits that can
be ORed together, but values.  In this case, _4 is the appropriate one
to use.

Signed-off-by: Danek Duvall <duvall@comfychair.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: correct use of IEEE80211_VHT_CAP_RXSTBC_X

[ Upstream commit 67d1ba8a6dc83d90cd58b89fa6cbf9ae35a0cf7f ]

The mod mask for VHT capabilities intends to say that you can override
the number of STBC receive streams, and it does, but only by accident.
The IEEE80211_VHT_CAP_RXSTBC_X aren't bits to be set, but values (albeit
left-shifted).  ORing the bits together gets the right answer, but we
should use the _MASK macro here instead.

Signed-off-by: Danek Duvall <duvall@comfychair.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: PPC: Book3S HV: Don't truncate HPTE index in xlate function

[ Upstream commit 46dec40fb741f00f1864580130779aeeaf24fb3d ]

This fixes a bug which causes guest virtual addresses to get translated
to guest real addresses incorrectly when the guest is using the HPT MMU
and has more than 256GB of RAM, or more specifically has a HPT larger
than 2GB.  This has showed up in testing as a failure of the host to
emulate doorbell instructions correctly on POWER9 for HPT guests with
more than 256GB of RAM.

The bug is that the HPTE index in kvmppc_mmu_book3s_64_hv_xlate()
is stored as an int, and in forming the HPTE address, the index gets
shifted left 4 bits as an int before being signed-extended to 64 bits.
The simple fix is to make the variable a long int, matching the
return type of kvmppc_hv_find_lock_hpte(), which is what calculates
the index.

Fixes: 697d3899dcb4 ("KVM: PPC: Implement MMIO emulation support for Book3S HV guests")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: Run TXQ teardown code before de-registering interfaces

[ Upstream commit 77cfaf52eca5cac30ed029507e0cab065f888995 ]

The TXQ teardown code can reference the vif data structures that are
stored in the netdev private memory area if there are still packets on
the queue when it is being freed. Since the TXQ teardown code is run
after the netdevs are freed, this can lead to a use-after-free. Fix this
by moving the TXQ teardown code to earlier in ieee80211_unregister_hw().

Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

time: Introduce jiffies64_to_nsecs()

commit 07e5f5e353aaa61696c8353d87050994a0c4648a upstream.

This will be needed for the cputime_t to nsec conversion.

Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1485832191-26889-2-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ivan Delalande <colona@arista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: mvebu-uart: Fix reporting of effective CSIZE to userspace

commit e0bf2d4982fe7d9ddaf550dd023803ea286f47fc upstream.

Apparently, this driver (or the hardware) does not support character
length settings. It's apparently running in 8-bit mode, but it makes
userspace believe it's in 5-bit mode. That makes tcsetattr with CS8
incorrectly fail, breaking e.g. getty from busybox, thus the login shell
on ttyMVx.

Fix by hard-wiring CS8 into c_cflag.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Fixes: 30530791a7a0 ("serial: mvebu-uart: initial support for Armada-3700 serial port")
Cc: stable <stable@vger.kernel.org> # 4.6+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.9.131

media: v4l: event: Prevent freeing event subscriptions while accessed

commit ad608fbcf166fec809e402d548761768f602702c upstream.

The event subscriptions are added to the subscribed event list while
holding a spinlock, but that lock is subsequently released while still
accessing the subscription object. This makes it possible to unsubscribe
the event --- and freeing the subscription object's memory --- while
the subscription object is simultaneously accessed.

Prevent this by adding a mutex to serialise the event subscription and
unsubscription. This also gives a guarantee to the callback ops that the
add op has returned before the del op is called.

This change also results in making the elems field less special:
subscriptions are only added to the event list once they are fully
initialised.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@vger.kernel.org # for 4.14 and up
Fixes: c3b5b0241f62 ("V4L/DVB: V4L: Events: Add backend")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: KVM: Sanitize PSTATE.M when being set from userspace

commit 2a3f93459d689d990b3ecfbe782fec89b97d3279 upstream.

Not all execution modes are valid for a guest, and some of them
depend on what the HW actually supports. Let's verify that what
userspace provides is compatible with both the VM settings and
the HW capabilities.

Cc: <stable@vger.kernel.org>
Fixes: 0d854a60b1d7 ("arm64: KVM: enable initialization of a 32bit vcpu")
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i2c: i801: Allow ACPI AML access I/O ports not reserved for SMBus

[ Upstream commit 7fd6d98b89f382d414e1db528e29a67bbd749457 ]

Commit 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict
with PCI BAR") made it possible for AML code to access SMBus I/O ports
by installing custom SystemIO OpRegion handler and blocking i80i driver
access upon first AML read/write to this OpRegion.

However, while ThinkPad T560 does have SystemIO OpRegion declared under
the SMBus device, it does not access any of the SMBus registers:

    Device (SMBU)
    {
        ...

        OperationRegion (SMBP, PCI_Config, 0x50, 0x04)
        Field (SMBP, DWordAcc, NoLock, Preserve)
        {
            ,   5,
            TCOB,   11,
            Offset (0x04)
        }

        Name (TCBV, 0x00)
        Method (TCBS, 0, NotSerialized)
        {
            If ((TCBV == 0x00))
            {
            TCBV = (\_SB.PCI0.SMBU.TCOB << 0x05)
            }

            Return (TCBV) /* \_SB_.PCI0.SMBU.TCBV */
        }

        OperationRegion (TCBA, SystemIO, TCBS (), 0x10)
        Field (TCBA, ByteAcc, NoLock, Preserve)
        {
            Offset (0x04),
            ,   9,
            CPSC,   1
        }
    }

Problem with the current approach is that it blocks all I/O port access
and because this system has touchpad connected to the SMBus controller
after first AML access (happens during suspend/resume cycle) the
touchpad fails to work anymore.

Fix this so that we allow ACPI AML I/O port access if it does not touch
the region reserved for the SMBus.

Fixes: 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict with PCI BAR")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200737
Reported-by: Yussuf Khalil <dev@pp3345.net>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm/arm64: smccc-1.1: Handle function result as parameters

[ Upstream commit 755a8bf5579d22eb5636685c516d8dede799e27b ]

If someone has the silly idea to write something along those lines:

extern u64 foo(void);

void bar(struct arm_smccc_res *res)
{
arm_smccc_1_1_smc(0xbad, foo(), res);
}

they are in for a surprise, as this gets compiled as:

0000000000000588 <bar>:
 588:   a9be7bfd        stp     x29, x30, [sp, #-32]!
 58c:   910003fd        mov     x29, sp
 590:   f9000bf3        str     x19, [sp, #16]
 594:   aa0003f3        mov     x19, x0
 598:   aa1e03e0        mov     x0, x30
 59c:   94000000        bl      0 <_mcount>
 5a0:   94000000        bl      0 <foo>
 5a4:   aa0003e1        mov     x1, x0
 5a8:   d4000003        smc     #0x0
 5ac:   b4000073        cbz     x19, 5b8 <bar+0x30>
 5b0:   a9000660        stp     x0, x1, [x19]
 5b4:   a9010e62        stp     x2, x3, [x19, #16]
 5b8:   f9400bf3        ldr     x19, [sp, #16]
 5bc:   a8c27bfd        ldp     x29, x30, [sp], #32
 5c0:   d65f03c0        ret
 5c4:   d503201f        nop

The call to foo "overwrites" the x0 register for the return value,
and we end up calling the wrong secure service.

A solution is to evaluate all the parameters before assigning
anything to specific registers, leading to the expected result:

0000000000000588 <bar>:
 588:   a9be7bfd        stp     x29, x30, [sp, #-32]!
 58c:   910003fd        mov     x29, sp
 590:   f9000bf3        str     x19, [sp, #16]
 594:   aa0003f3        mov     x19, x0
 598:   aa1e03e0        mov     x0, x30
 59c:   94000000        bl      0 <_mcount>
 5a0:   94000000        bl      0 <foo>
 5a4:   aa0003e1        mov     x1, x0
 5a8:   d28175a0        mov     x0, #0xbad
 5ac:   d4000003        smc     #0x0
 5b0:   b4000073        cbz     x19, 5bc <bar+0x34>
 5b4:   a9000660        stp     x0, x1, [x19]
 5b8:   a9010e62        stp     x2, x3, [x19, #16]
 5bc:   f9400bf3        ldr     x19, [sp, #16]
 5c0:   a8c27bfd        ldp     x29, x30, [sp], #32
 5c4:   d65f03c0        ret

Reported-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm/arm64: smccc-1.1: Make return values unsigned long

[ Upstream commit 1d8f574708a3fb6f18c85486d0c5217df893c0cf ]

An unfortunate consequence of having a strong typing for the input
values to the SMC call is that it also affects the type of the
return values, limiting r0 to 32 bits and r{1,2,3} to whatever
was passed as an input.

Let's turn everything into "unsigned long", which satisfies the
requirements of both architectures, and allows for the full
range of return values.

Reported-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu: Update power state at the end of smu hw_init.

[ Upstream commit 2ab4d0e74256fc49b7b270f63c1d1e47c2455abc ]

For SI/Kv, the power state is managed by function
amdgpu_pm_compute_clocks.

when dpm enabled, we should call amdgpu_pm_compute_clocks
to update current power state instand of set boot state.

this change can fix the oops when kfd driver was enabled on Kv.

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu: Enable/disable gfx PG feature in rlc safe mode

[ Upstream commit 8ef23364b654d44244400d79988e677e504b21ba ]

This is required by gfx hw and can fix the rlc hang when
do s3 stree test on Cz/St.

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Hang Zhou <hang.zhou@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hwmon: (adt7475) Make adt7475_read_word() return errors

[ Upstream commit f196dec6d50abb2e65fb54a0621b2f1b4d922995 ]

The adt7475_read_word() function was meant to return negative error
codes on failure.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hwmon: (ina2xx) fix sysfs shunt resistor read access

[ Upstream commit 3ad867001c91657c46dcf6656d52eb6080286fd5 ]

fix the sysfs shunt resistor read access: return the shunt resistor
value, not the calibration register contents.

update email address

Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

e1000: ensure to free old tx/rx rings in set_ringparam()

[ Upstream commit ee400a3f1bfe7004a3e14b81c38ccc5583c26295 ]

In 'e1000_set_ringparam()', the tx_ring and rx_ring are updated with new value
and the old tx/rx rings are freed only when the device is up. There are resource
leaks on old tx/rx rings when the device is not up. This bug is reported by COD,
a tool for testing kernel module binaries I am building.

This patch fixes the bug by always calling 'kfree()' on old tx/rx rings in
'e1000_set_ringparam()'.

Signed-off-by: Bo Chen <chenbo@pdx.edu>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

e1000: check on netif_running() before calling e1000_up()

[ Upstream commit cf1acec008f8d7761aa3fd7c4bca7e17b2d2512d ]

When the device is not up, the call to 'e1000_up()' from the error handling path
of 'e1000_set_ringparam()' causes a kernel oops with a null-pointer
dereference. The null-pointer dereference is triggered in function
'e1000_alloc_rx_buffers()' at line 'buffer_info = &rx_ring->buffer_info[i]'.

This bug was reported by COD, a tool for testing kernel module binaries I am
building. This bug was also detected by KFI from Dr. Kai Cong.

This patch fixes the bug by checking on 'netif_running()' before calling
'e1000_up()' in 'e1000_set_ringparam()'.

Signed-off-by: Bo Chen <chenbo@pdx.edu>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: hns: fix skb->truesize underestimation

[ Upstream commit b1ccd4c0ab6ef499f47dd84ed4920502a7147bba ]

skb->truesize is not meant to be tracking amount of used bytes in a skb,
but amount of reserved/consumed bytes in memory.

For instance, if we use a single byte in last page fragment, we have to
account the full size of the fragment.

So skb_add_rx_frag needs to calculate the length of the entire buffer into
turesize.

Fixes: 9cbe9fd5214e ("net: hns: optimize XGE capability by reducing cpu usage")
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: hns: fix length and page_offset overflow when CONFIG_ARM64_64K_PAGES

[ Upstream commit 3ed614dce3ca9912d22be215ff0f11104b69fe62 ]

When enable the config item "CONFIG_ARM64_64K_PAGES", the size of PAGE_SIZE
is 65536(64K). But the  type of length and page_offset are u16, they will
overflow. So change them to u32.

Fixes: 6fe6611ff275 ("net: add Hisilicon Network Subsystem hnae framework support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thermal: of-thermal: disable passive polling when thermal zone is disabled

[ Upstream commit 152395fd03d4ce1e535a75cdbf58105e50587611 ]

When thermal zone is in passive mode, disabling its mode from
sysfs is NOT taking effect at all, it is still polling the
temperature of the disabled thermal zone and handling all thermal
trips, it makes user confused. The disabling operation should
disable the thermal zone behavior completely, for both active and
passive mode, this patch clears the passive_delay when thermal
zone is disabled and restores it when it is enabled.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

qed: Wait for MCP halt and resume commands to take place

[ Upstream commit 76271809f49056f079e202bf6513d17b0d6dd34d ]

Successive iterations of halting and resuming the management chip (MCP)
might fail, since currently the driver doesn't wait for these operations to
actually take place.
This patch prevents the driver from moving forward before the operations
are reflected in the state register.

Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

qed: Wait for ready indication before rereading the shmem

[ Upstream commit f00d25f3154b676fcea4502a25b94bd7f142ca74 ]

The MFW might be reset and re-update its shared memory.
Upon the detection of such a reset the driver rereads this memory, but it
has to wait till the data is valid.
This patch adds the missing wait for a data ready indication.

Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: never move the system.data xattr out of the inode body

commit 8cdb5240ec5928b20490a2bb34cb87e9a5f40226 upstream.

When expanding the extra isize space, we must never move the
system.data xattr out of the inode body.  For performance reasons, it
doesn't make any sense, and the inline data implementation assumes
that system.data xattr is never in the external xattr block.

This addresses CVE-2018-10880

https://bugzilla.kernel.org/show_bug.cgi?id=200005

Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
[groeck: Context changes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: KVM: Tighten guest core register access from userspace

commit d26c25a9d19b5976b319af528886f89cf455692d upstream.

We currently allow userspace to access the core register file
in about any possible way, including straddling multiple
registers and doing unaligned accesses.

This is not the expected use of the ABI, and nobody is actually
using it that way. Let's tighten it by explicitly checking
the size and alignment for each field of the register file.

Cc: <stable@vger.kernel.org>
Fixes: 2f4a07c5f9fe ("arm64: KVM: guest one-reg interface")
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
[maz: rewrote Dave's initial patch to be more easily backported]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/hfi1: Fix SL array bounds check

commit 0dbfaa9f2813787679e296eb5476e40938ab48c8 upstream.

The SL specified by a user needs to be a valid SL.

Add a range check to the user specified SL value which protects from
running off the end of the SL to SC table.

CC: stable@vger.kernel.org
Fixes: 7724105686e7 ("IB/hfi1: add driver files")
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: imx: restore handshaking irq for imx1

commit 7e620984b62532783912312e334f3c48cdacbd5d upstream.

Back in 2015 when irda was dropped from the driver imx1 was broken. This
change reintroduces the support for the third interrupt of the UART.

Fixes: afe9cbb1a6ad ("serial: imx: drop support for IRDA")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: target: iscsi: Use bin2hex instead of a re-implementation

commit 8c39e2699f8acb2e29782a834e56306da24937fe upstream.

Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[plr.vincent@gmail.com: hunk context change for 4.4 and 4.9, no code change]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/hfi1: Fix context recovery when PBC has an UnsupportedVL

commit d623500b3c4efd8d4e945ac9003c6b87b469a9ab upstream.

If a packet stream uses an UnsupportedVL (virtual lane), the send
engine will not send the packet, and it will not indicate that an
error has occurred.  This will cause the packet stream to block.

HFI has 8 virtual lanes available for packet streams.  Each lane can
be enabled or disabled using the UnsupportedVL mask.  If a lane is
disabled, adding a packet to the send context must be disallowed.

The current mask for determining unsupported VLs defaults to 0 (allow
all).  This is incorrect.  Only the VLs that are defined should be
allowed.

Determine which VLs are disabled (mtu == 0), and set the appropriate
unsupported bit in the mask.  The correct mask will allow the send
engine to error on the invalid VL, and error recovery will work
correctly.

Cc: <stable@vger.kernel.org> # 4.9.x+
Fixes: 7724105686e7 ("IB/hfi1: add driver files")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Lukasz Odzioba <lukasz.odzioba@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/hfi1: Invalid user input can result in crash

commit 94694d18cf27a6faad91487a38ce516c2b16e7d9 upstream.

If the number of packets in a user sdma request does not match
the actual iovectors being sent, sdma_cleanup can be called on
an uninitialized request structure, resulting in a crash similar
to this:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: [<ffffffffc0ae8bb7>] __sdma_txclean+0x57/0x1e0 [hfi1]
PGD 8000001044f61067 PUD 1052706067 PMD 0
Oops: 0000 [#1] SMP
CPU: 30 PID: 69912 Comm: upsm Kdump: loaded Tainted: G           OE
------------   3.10.0-862.el7.x86_64 #1
Hardware name: Intel Corporation S2600KPR/S2600KPR, BIOS
SE5C610.86B.01.01.0019.101220160604 10/12/2016
task: ffff8b331c890000 ti: ffff8b2ed1f98000 task.ti: ffff8b2ed1f98000
RIP: 0010:[<ffffffffc0ae8bb7>]  [<ffffffffc0ae8bb7>] __sdma_txclean+0x57/0x1e0
[hfi1]
RSP: 0018:ffff8b2ed1f9bab0  EFLAGS: 00010286
RAX: 0000000000008b2b RBX: ffff8b2adf6e0000 RCX: 0000000000000000
RDX: 00000000000000a0 RSI: ffff8b2e9eedc540 RDI: ffff8b2adf6e0000
RBP: ffff8b2ed1f9bad8 R08: 0000000000000000 R09: ffffffffc0b04a06
R10: ffff8b331c890190 R11: ffffe6ed00bf1840 R12: ffff8b3315480000
R13: ffff8b33154800f0 R14: 00000000fffffff2 R15: ffff8b2e9eedc540
FS:  00007f035ac47740(0000) GS:ffff8b331e100000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 0000000c03fe6000 CR4: 00000000001607e0
Call Trace:
 [<ffffffffc0b0570d>] user_sdma_send_pkts+0xdcd/0x1990 [hfi1]
 [<ffffffff9fe75fb0>] ? gup_pud_range+0x140/0x290
 [<ffffffffc0ad3105>] ? hfi1_mmu_rb_insert+0x155/0x1b0 [hfi1]
 [<ffffffffc0b0777b>] hfi1_user_sdma_process_request+0xc5b/0x11b0 [hfi1]
 [<ffffffffc0ac193a>] hfi1_aio_write+0xba/0x110 [hfi1]
 [<ffffffffa001a2bb>] do_sync_readv_writev+0x7b/0xd0
 [<ffffffffa001bede>] do_readv_writev+0xce/0x260
 [<ffffffffa022b089>] ? tty_ldisc_deref+0x19/0x20
 [<ffffffffa02268c0>] ? n_tty_ioctl+0xe0/0xe0
 [<ffffffffa001c105>] vfs_writev+0x35/0x60
 [<ffffffffa001c2bf>] SyS_writev+0x7f/0x110
 [<ffffffffa051f7d5>] system_call_fastpath+0x1c/0x21
Code: 06 49 c7 47 18 00 00 00 00 0f 87 89 01 00 00 5b 41 5c 41 5d 41 5e 41 5f
5d c3 66 2e 0f 1f 84 00 00 00 00 00 48 8b 4e 10 48 89 fb <48> 8b 51 08 49 89 d4
83 e2 0c 41 81 e4 00 e0 00 00 48 c1 ea 02
RIP  [<ffffffffc0ae8bb7>] __sdma_txclean+0x57/0x1e0 [hfi1]
 RSP <ffff8b2ed1f9bab0>
CR2: 0000000000000008

There are two exit points from user_sdma_send_pkts().  One (free_tx)
merely frees the slab entry and one (free_txreq) cleans the sdma_txreq
prior to freeing the slab entry.   The free_txreq variation can only be
called after one of the sdma_init*() variations has been called.

In the panic case, the slab entry had been allocated but not inited.

Fix the issue by exiting through free_tx thus avoiding sdma_clean().

Cc: <stable@vger.kernel.org> # 4.9.x+
Fixes: 7724105686e7 ("IB/hfi1: add driver files")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Lukasz Odzioba <lukasz.odzioba@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>

IB/srp: Avoid that sg_reset -d ${srp_device} triggers an infinite loop

commit ee92efe41cf358f4b99e73509f2bfd4733609f26 upstream.

Use different loop variables for the inner and outer loop. This avoids
that an infinite loop occurs if there are more RDMA channels than
target->req_ring_size.

Fixes: d92c0da71a35 ("IB/srp: Add multichannel support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: elantech - enable middle button of touchpad on ThinkPad P72

commit 91a97507323e1ad4bfc10f4a5922e67cdaf8b3cd upstream.

Adding 2 new touchpad IDs to support middle button support.

Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: remove LPM management from usb_driver_claim_interface()

commit c183813fcee44a249339b7c46e1ad271ca1870aa upstream.

usb_driver_claim_interface() disables and re-enables Link Power
Management, but it shouldn't do either one, for the reasons listed
below.  This patch removes the two LPM-related function calls from the
routine.

The reason for disabling LPM in the analogous function
usb_probe_interface() is so that drivers won't have to deal with
unwanted LPM transitions in their probe routine.  But
usb_driver_claim_interface() doesn't call the driver's probe routine
(or any other callbacks), so that reason doesn't apply here.

Furthermore, no driver other than usbfs will ever call
usb_driver_claim_interface() unless it is already bound to another
interface in the same device, which means disabling LPM here would be
redundant.  usbfs doesn't interact with LPM at all.

Lastly, the error return from usb_unlocked_disable_lpm() isn't handled
properly; the code doesn't clean up its earlier actions before
returning.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 8306095fd2c1 ("USB: Disable USB 3.0 LPM in critical sections.")
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "usb: cdc-wdm: Fix a sleep-in-atomic-context bug in service_outstanding_interrupt()"

commit e871db8d78df1c411032cbb3acfdf8930509360e upstream.

This reverts commit 6e22e3af7bb3a7b9dc53cb4687659f6e63fca427.

The bug the patch describes to, has been already fixed in commit
2df6948428542 ("USB: cdc-wdm: don't enable interrupts in USB-giveback")
so need to this, revert it.

Fixes: 6e22e3af7bb3 ("usb: cdc-wdm: Fix a sleep-in-atomic-context bug in service_outstanding_interrupt()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usbdevfs: restore warning for nonsensical flags

commit 81e0403b26d94360abd1f6a57311337973bc82cd upstream.

If we filter flags before they reach the core we need to generate our
own warnings.

Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 0cb54a3e47cb ("USB: debugging code shouldn't alter control flow")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usbdevfs: sanitize flags more

commit 7a68d9fb851012829c29e770621905529bd9490b upstream.

Requesting a ZERO_PACKET or not is sensible only for output.
In the input direction the device decides.
Likewise accepting short packets makes sense only for input.

This allows operation with panic_on_warn without opening up
a local DOS.

Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+843efa30c8821bd69f53@syzkaller.appspotmail.com
Fixes: 0cb54a3e47cb ("USB: debugging code shouldn't alter control flow")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: uvcvideo: Support realtek's UVC 1.5 device

commit f620d1d7afc7db57ab59f35000752840c91f67e7 upstream.

media: uvcvideo: Support UVC 1.5 video probe & commit controls

The length of UVC 1.5 video control is 48, and it is 34 for UVC 1.1.
Change it to 48 for UVC 1.5 device, and the UVC 1.5 device can be
recognized.

More changes to the driver are needed for full UVC 1.5 compatibility.
However, at least the UVC 1.5 Realtek RTS5847/RTS5852 cameras have been
reported to work well.

[laurent.pinchart@ideasonboard.com: Factor out code to helper function, update size checks]

Cc: stable@vger.kernel.org
Signed-off-by: ming_qian <ming_qian@realsil.com.cn>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Ana Guerrero Lopez <ana.guerrero@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

slub: make ->cpu_partial unsigned int

commit e5d9998f3e09359b372a037a6ac55ba235d95d57 upstream.

/*
 * cpu_partial determined the maximum number of objects
 * kept in the per cpu partial lists of a processor.
 */

Can't be negative.

Link: http://lkml.kernel.org/r/20180305200730.15812-15-adobriyan@gmail.com
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: handle NULL config in usb_find_alt_setting()

commit c9a4cb204e9eb7fa7dfbe3f7d3a674fa530aa193 upstream.

usb_find_alt_setting() takes a pointer to a struct usb_host_config as
an argument; it searches for an interface with specified interface and
alternate setting numbers in that config.  However, it crashes if the
usb_host_config pointer argument is NULL.

Since this is a general-purpose routine, available for use in many
places, we want to to be more robust.  This patch makes it return NULL
whenever the config argument is NULL.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+19c3aaef85a89d451eac@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: fix error handling in usb_driver_claim_interface()

commit bd729f9d67aa9a303d8925bb8c4f06af25f407d1 upstream.

The syzbot fuzzing project found a use-after-free bug in the USB
core.  The bug was caused by usbfs not unbinding from an interface
when the USB device file was closed, which led another process to
attempt the unbind later on, after the private data structure had been
deallocated.

The reason usbfs did not unbind the interface at the appropriate time
was because it thought the interface had never been claimed in the
first place.  This was caused by the fact that
usb_driver_claim_interface() does not clean up properly when
device_bind_driver() returns an error.  Although the error code gets
passed back to the caller, the iface->dev.driver pointer remains set
and iface->condition remains equal to USB_INTERFACE_BOUND.

This patch adds proper error handling to usb_driver_claim_interface().

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+f84aa7209ccec829536f@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

regulator: fix crash caused by null driver data

commit fb6de923ca3358a91525552b4907d4cb38730bdd upstream.

dev_set_drvdata() needs to be called before device_register()
exposes device to userspace. Otherwise kernel crashes after it
gets null pointer from dev_get_drvdata() when userspace tries
to access sysfs entries.

[Removed backtrace for length -- broonie]

Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: rspi: Fix interrupted DMA transfers

commit 8dbbaa47b96f6ea5f09f922b4effff3c505cd8cf upstream.

When interrupted, wait_event_interruptible_timeout() returns
-ERESTARTSYS, and the SPI transfer in progress will fail, as expected:

    m25p80 spi0.0: SPI transfer failed: -512
    spi_master spi0: failed to transfer one message from queue

However, as the underlying DMA transfers may not have completed, all
subsequent SPI transfers may start to fail:

    spi_master spi0: receive timeout
    qspi_transfer_out_in() returned -110
    m25p80 spi0.0: SPI transfer failed: -110
    spi_master spi0: failed to transfer one message from queue

Fix this by calling dmaengine_terminate_all() not only for timeouts, but
also for errors.

This can be reproduced on r8a7991/koelsch, using "hd /dev/mtd0" followed
by CTRL-C.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: rspi: Fix invalid SPI use during system suspend

commit c1ca59c22c56930b377a665fdd1b43351887830b upstream.

If the SPI queue is running during system suspend, the system may lock
up.

Fix this by stopping/restarting the queue during system suspend/resume,
by calling spi_master_suspend()/spi_master_resume() from the PM
callbacks.  In-kernel users will receive an -ESHUTDOWN error while
system suspend/resume is in progress.

Based on a patch for sh-msiof by Gaku Inami.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: sh-msiof: Fix handling of write value for SISTR register

commit 31a5fae4c5a009898da6d177901d5328051641ff upstream.

This patch changes writing to the SISTR register according to the H/W
user's manual.

The TDREQ bit and RDREQ bits of SISTR are read-only, and must be written
their initial values of zero.

Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
[geert: reword]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: sh-msiof: Fix invalid SPI use during system suspend

commit ffa69d6a16f686efe45269342474e421f2aa58b2 upstream.

If the SPI queue is running during system suspend, the system may lock
up.

Fix this by stopping/restarting the queue during system suspend/resume
by calling spi_master_suspend()/spi_master_resume() from the PM
callbacks.  In-kernel users will receive an -ESHUTDOWN error while
system suspend/resume is in progress.

Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
[geert: Cleanup, reword]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: tegra20-slink: explicitly enable/disable clock

commit 7001cab1dabc0b72b2b672ef58a90ab64f5e2343 upstream.

Depending on the SPI instance one may get an interrupt storm upon
requesting resp. interrupt unless the clock is explicitly enabled
beforehand. This has been observed trying to bring up instance 4 on
T20.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: cpm_uart: return immediately from console poll

commit be28c1e3ca29887e207f0cbcd294cefe5074bab6 upstream.

kgdb expects poll function to return immediately and
returning NO_POLL_CHAR when no character is available.

Fixes: f5316b4aea024 ("kgdb,8250,pl011: Return immediately from console poll")
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: lpuart: avoid leaking struct tty_struct

commit 3216c622a24b0ebb9c159a8d1daf7f17a106b3f5 upstream.

The function tty_port_tty_get() gets a reference to the tty. Since
the code is not using tty_port_tty_set(), the reference is kept
even after closing the tty.

Avoid using tty_port_tty_get() by directly access the tty instance.
Since lpuart_start_rx_dma() is called from the .startup() and
.set_termios() callback, it is safe to assume the tty instance is
valid.

Cc: stable@vger.kernel.org # v4.9+
Fixes: 5887ad43ee02 ("tty: serial: fsl_lpuart: Use cyclic DMA for Rx")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

floppy: Do not copy a kernel pointer to user memory in FDGETPRM ioctl

commit 65eea8edc315589d6c993cf12dbb5d0e9ef1fe4e upstream.

The final field of a floppy_struct is the field "name", which is a pointer
to a string in kernel memory.  The kernel pointer should not be copied to
user memory.  The FDGETPRM ioctl copies a floppy_struct to user memory,
including this "name" field.  This pointer cannot be used by the user
and it will leak a kernel address to user-space, which will reveal the
location of kernel code and data and undermine KASLR protection.

Model this code after the compat ioctl which copies the returned data
to a previously cleared temporary structure on the stack (excluding the
name pointer) and copy out to userspace from there.  As we already have
an inparam union with an appropriate member and that memory is already
cleared even for read only calls make use of that as a temporary store.

Based on an initial patch by Brian Belleville.

CVE-2018-7755
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Broke up long line.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: dra7: fix DCAN node addresses

[ Upstream commit 949bdcc8a97c6078f21c8d4966436b117f2e4cd3 ]

Fix the DT node addresses to match the reg property addresses,
which were verified to match the TRM:
http://www.ti.com/lit/pdf/sprui30

Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

EDAC: Fix memleak in module init error path

[ Upstream commit 4708aa85d50cc6e962dfa8acf5ad4e0d290a21db ]

Make sure to use put_device() to free the initialised struct device so
that resources managed by driver core also gets released in the event of
a registration failure.

Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Denis Kirjanov <kirjanov@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Fixes: 2d56b109e3a5 ("EDAC: Handle error path in edac_mc_sysfs_init() properly")
Link: http://lkml.kernel.org/r/20180612124335.6420-1-johan@kernel.org
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nfsd: fix corrupted reply to badly ordered compound

[ Upstream commit 5b7b15aee641904ae269be9846610a3950cbd64c ]

We're encoding a single op in the reply but leaving the number of ops
zero, so the reply makes no sense.

Somewhat academic as this isn't a case any real client will hit, though
in theory perhaps that could change in a future protocol extension.

Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gpio: Fix wrong rounding in gpio-menz127

[ Upstream commit 7279d9917560bbd0d82813d6bf00490a82c06783 ]

men_z127_debounce() tries to round up and down, but uses functions which
are only suitable when the divider is a power of two, which is not the
case. Use the appropriate ones.

Found by static check. Compile tested.

Fixes: f436bc2726c64 ("gpio: add driver for MEN 16Z127 GPIO controller")
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

module: exclude SHN_UNDEF symbols from kallsyms api

[ Upstream commit 9f2d1e68cf4d641def734adaccfc3823d3575e6c ]

Livepatch modules are special in that we preserve their entire symbol
tables in order to be able to apply relocations after module load. The
unwanted side effect of this is that undefined (SHN_UNDEF) symbols of
livepatch modules are accessible via the kallsyms api and this can
confuse symbol resolution in livepatch (klp_find_object_symbol()) and
cause subtle bugs in livepatch.

Have the module kallsyms api skip over SHN_UNDEF symbols. These symbols
are usually not available for normal modules anyway as we cut down their
symbol tables to just the core (non-undefined) symbols, so this should
really just affect livepatch modules. Note that this patch doesn't
affect the display of undefined symbols in /proc/kallsyms.

Reported-by: Josh Poimboeuf <jpoimboe@redhat.com>
Tested-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: dapm: Fix potential DAI widget pointer deref when linking DAIs

[ Upstream commit e01b4f624278d5efe5fb5da585ca371947b16680 ]

Sometime a component or topology may configure a DAI widget with no
private data leading to a dev_dbg() dereferencne of this data.

Fix this to check for non NULL private data and let users know if widget
is missing DAI.

Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

EDAC, i7core: Fix memleaks and use-after-free on probe and remove

[ Upstream commit 6c974d4dfafe5e9ee754f2a6fba0eb1864f1649e ]

Make sure to free and deregister the addrmatch and chancounts devices
allocated during probe in all error paths. Also fix use-after-free in a
probe error path and in the remove success path where the devices were
being put before before deregistration.

Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Fixes: 356f0a30860d ("i7core_edac: change the mem allocation scheme to make Documentation/kobject.txt happy")
Link: http://lkml.kernel.org/r/20180612124335.6420-2-johan@kernel.org
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: megaraid_sas: Update controller info during resume

[ Upstream commit c3b10a55abc943a526aaecd7e860b15671beb906 ]

There is a possibility that firmware on the controller was upgraded before
system was suspended. During resume, driver needs to read updated
controller properties.

Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: bnx2i: add error handling for ioremap_nocache

[ Upstream commit aa154ea885eb0c2407457ce9c1538d78c95456fa ]

When ioremap_nocache fails, the lack of error-handling code may cause
unexpected results.

This patch adds error-handling code after calling ioremap_nocache.

Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf/x86/intel/lbr: Fix incomplete LBR call stack

[ Upstream commit 0592e57b24e7e05ec1f4c50b9666c013abff7017 ]

LBR has a limited stack size. If a task has a deeper call stack than
LBR's stack size, only the overflowed part is reported. A complete call
stack may not be reconstructed by perf tool.

Current code doesn't access all LBR registers. It only read the ones
below the TOS. The LBR registers above the TOS will be discarded
unconditionally.

When a CALL is captured, the TOS is incremented by 1 , modulo max LBR
stack size. The LBR HW only records the call stack information to the
register which the TOS points to. It will not touch other LBR
registers. So the registers above the TOS probably still store the valid
call stack information for an overflowed call stack, which need to be
reported.

To retrieve complete call stack information, we need to start from TOS,
read all LBR registers until an invalid entry is detected.
0s can be used to detect the invalid entry, because:

 - When a RET is captured, the HW zeros the LBR register which TOS points
   to, then decreases the TOS.
 - The LBR registers are reset to 0 when adding a new LBR event or
   scheduling an existing LBR event.
 - A taken branch at IP 0 is not expected

The context switch code is also modified to save/restore all valid LBR
registers. Furthermore, the LBR registers, which don't have valid call
stack information, need to be reset in restore, because they may be
polluted while swapped out.

Here is a small test program, tchain_deep.
Its call stack is deeper than 32.

 noinline void f33(void)
 {
        int i;

        for (i = 0; i < 10000000;) {
                if (i%2)
                        i++;
                else
                        i++;
        }
 }

 noinline void f32(void)
 {
        f33();
 }

 noinline void f31(void)
 {
        f32();
 }

 ... ...

 noinline void f1(void)
 {
        f2();
 }

 int main()
 {
        f1();
 }

Here is the test result on SKX. The max stack size of SKX is 32.

Without the patch:

 $ perf record -e cycles --call-graph lbr -- ./tchain_deep
 $ perf report --stdio
 #
 # Children      Self  Command      Shared Object     Symbol
 # ........  ........  ...........  ................  .................
 #
   100.00%    99.99%  tchain_deep    tchain_deep       [.] f33
            |
             --99.99%--f30
                       f31
                       f32
                       f33

With the patch:

 $ perf record -e cycles --call-graph lbr -- ./tchain_deep
 $ perf report --stdio
 # Children      Self  Command      Shared Object     Symbol
 # ........  ........  ...........  ................  ..................
 #
    99.99%     0.00%  tchain_deep    tchain_deep       [.] f1
            |
            ---f1
               f2
               f3
               f4
               f5
               f6
               f7
               f8
               f9
               f10
               f11
               f12
               f13
               f14
               f15
               f16
               f17
               f18
               f19
               f20
               f21
               f22
               f23
               f24
               f25
               f26
               f27
               f28
               f29
               f30
               f31
               f32
               f33

Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@kernel.org
Cc: eranian@google.com
Link: https://lore.kernel.org/lkml/1528213126-4312-1-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: hid-ntrig: add error handling for sysfs_create_group

[ Upstream commit 44d4d51de9a3534a2b63d69efda02a10e66541e4 ]

When sysfs_create_group fails, the lack of error-handling code may
cause unexpected results.

This patch adds error-handling code after calling sysfs_create_group.

Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: mvebu: declare asm symbols as character arrays in pmsu.c

[ Upstream commit d0d378ff451a66e486488eec842e507d28145813 ]

With CONFIG_FORTIFY_SOURCE, memcpy uses the declared size of operands to
detect buffer overflows.  If src or dest is declared as a char, attempts to
copy more than byte will result in a fortify_panic().

Address this problem in mvebu_setup_boot_addr_wa() by declaring
mvebu_boot_wa_start and mvebu_boot_wa_end as character arrays.  Also remove
a couple addressof operators to avoid "arithmetic on pointer to an
incomplete type" compiler error.

See commit 54a7d50b9205 ("x86: mark kprobe templates as character arrays,
not single characters") for a similar fix.

Fixes "detected buffer overflow in memcpy" error during init on some mvebu
systems (armada-370-xp, armada-375):

(fortify_panic) from (mvebu_setup_boot_addr_wa+0xb0/0xb4)
(mvebu_setup_boot_addr_wa) from (mvebu_v7_cpu_pm_init+0x154/0x204)
(mvebu_v7_cpu_pm_init) from (do_one_initcall+0x7c/0x1a8)
(do_one_initcall) from (kernel_init_freeable+0x1bc/0x254)
(kernel_init_freeable) from (kernel_init+0x8/0x114)
(kernel_init) from (ret_from_fork+0x14/0x2c)

Signed-off-by: Ethan Tuttle <ethan@ethantuttle.com>
Tested-by: Ethan Tuttle <ethan@ethantuttle.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wlcore: Add missing PM call for wlcore_cmd_wait_for_event_or_timeout()

[ Upstream commit 4ec7cece87b3ed21ffcd407c62fb2f151a366bc1 ]

Otherwise we can get:

WARNING: CPU: 0 PID: 55 at drivers/net/wireless/ti/wlcore/io.h:84

I've only seen this few times with the runtime PM patches enabled
so this one is probably not needed before that. This seems to
work currently based on the current PM implementation timer. Let's
apply this separately though in case others are hitting this issue.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rndis_wlan: potential buffer overflow in rndis_wlan_auth_indication()

[ Upstream commit ae636fb1554833ee5133ca47bf4b2791b6739c52 ]

This is a static checker fix, not something I have tested.  The issue
is that on the second iteration through the loop, we jump forward by
le32_to_cpu(auth_req->length) bytes.  The problem is that if the length
is more than "buflen" then we end up with a negative "buflen".  A
negative buflen is type promoted to a high positive value and the loop
continues but it's accessing beyond the end of the buffer.

I believe the "auth_req->length" comes from the firmware and if the
firmware is malicious or buggy, you're already toasted so the impact of
this bug is probably not very severe.

Fixes: 030645aceb3d ("rndis_wlan: handle 802.11 indications from device")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/sun4i: Fix releasing node when enumerating enpoints

[ Upstream commit 367c359aa8637b15ee8df6335c5a29b7623966ec ]

sun4i_drv_add_endpoints() has a memory leak since it uses of_node_put()
when remote is equal to NULL and does nothing when remote has a valid
pointer.

Invert the logic to fix memory leak.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-7-jernej.skrabec@siol.net
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: phy: xgmiitorgmii: Check phy_driver ready before accessing

[ Upstream commit ab4e6ee578e88a659938db8fbf33720bc048d29c ]

Since a phy_device is added to the global mdio_bus list during
phy_device_register(), but a phy_device's phy_driver doesn't get
attached until phy_probe(). It's possible of_phy_find_device() in
xgmiitorgmii will return a valid phy with a NULL phy_driver. Leading to
a NULL pointer access during the memcpy().

Fixes this Oops:

Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.14.40 #1
Hardware name: Xilinx Zynq Platform
task: ce4c8d00 task.stack: ce4ca000
PC is at memcpy+0x48/0x330
LR is at xgmiitorgmii_probe+0x90/0xe8
pc : [<c074bc68>]    lr : [<c0529548>]    psr: 20000013
sp : ce4cbb54  ip : 00000000  fp : ce4cbb8c
r10: 00000000  r9 : 00000000  r8 : c0c49178
r7 : 00000000  r6 : cdc14718  r5 : ce762800  r4 : cdc14710
r3 : 00000000  r2 : 00000054  r1 : 00000000  r0 : cdc14718
Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
Control: 18c5387d  Table: 0000404a  DAC: 00000051
Process swapper/0 (pid: 1, stack limit = 0xce4ca210)
...
[<c074bc68>] (memcpy) from [<c0529548>] (xgmiitorgmii_probe+0x90/0xe8)
[<c0529548>] (xgmiitorgmii_probe) from [<c0526a94>] (mdio_probe+0x28/0x34)
[<c0526a94>] (mdio_probe) from [<c04db98c>] (driver_probe_device+0x254/0x414)
[<c04db98c>] (driver_probe_device) from [<c04dbd58>] (__device_attach_driver+0xac/0x10c)
[<c04dbd58>] (__device_attach_driver) from [<c04d96f4>] (bus_for_each_drv+0x84/0xc8)
[<c04d96f4>] (bus_for_each_drv) from [<c04db5bc>] (__device_attach+0xd0/0x134)
[<c04db5bc>] (__device_attach) from [<c04dbdd4>] (device_initial_probe+0x1c/0x20)
[<c04dbdd4>] (device_initial_probe) from [<c04da8fc>] (bus_probe_device+0x98/0xa0)
[<c04da8fc>] (bus_probe_device) from [<c04d8660>] (device_add+0x43c/0x5d0)
[<c04d8660>] (device_add) from [<c0526cb8>] (mdio_device_register+0x34/0x80)
[<c0526cb8>] (mdio_device_register) from [<c0580b48>] (of_mdiobus_register+0x170/0x30c)
[<c0580b48>] (of_mdiobus_register) from [<c05349c4>] (macb_probe+0x710/0xc00)
[<c05349c4>] (macb_probe) from [<c04dd700>] (platform_drv_probe+0x44/0x80)
[<c04dd700>] (platform_drv_probe) from [<c04db98c>] (driver_probe_device+0x254/0x414)
[<c04db98c>] (driver_probe_device) from [<c04dbc58>] (__driver_attach+0x10c/0x118)
[<c04dbc58>] (__driver_attach) from [<c04d9600>] (bus_for_each_dev+0x8c/0xd0)
[<c04d9600>] (bus_for_each_dev) from [<c04db1fc>] (driver_attach+0x2c/0x30)
[<c04db1fc>] (driver_attach) from [<c04daa98>] (bus_add_driver+0x50/0x260)
[<c04daa98>] (bus_add_driver) from [<c04dc440>] (driver_register+0x88/0x108)
[<c04dc440>] (driver_register) from [<c04dd6b4>] (__platform_driver_register+0x50/0x58)
[<c04dd6b4>] (__platform_driver_register) from [<c0b31248>] (macb_driver_init+0x24/0x28)
[<c0b31248>] (macb_driver_init) from [<c010203c>] (do_one_initcall+0x60/0x1a4)
[<c010203c>] (do_one_initcall) from [<c0b00f78>] (kernel_init_freeable+0x15c/0x1f8)
[<c0b00f78>] (kernel_init_freeable) from [<c0763d10>] (kernel_init+0x18/0x124)
[<c0763d10>] (kernel_init) from [<c0112d74>] (ret_from_fork+0x14/0x20)
Code: ba000002 f5d1f03c f5d1f05c f5d1f07c (e8b151f8)
---[ end trace 3e4ec21905820a1f ]---

Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ath10k: protect ath10k_htt_rx_ring_free with rx_ring.lock

[ Upstream commit 168f75f11fe68455e0d058a818ebccfc329d8685 ]

While debugging driver crashes related to a buggy firmware
crashing under load, I noticed that ath10k_htt_rx_ring_free
could be called without being under lock.  I'm not sure if this
is the root cause of the crash or not, but it seems prudent to
protect it.

Originally tested on 4.16+ kernel with ath10k-ct 10.4 firmware
running on 9984 NIC.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: phy: xgmiitorgmii: Check read_status results

[ Upstream commit 8d0752d11312be830c33e84dfd1016e6a47c2938 ]

We're ignoring the result of the attached phy device's read_status().
Return it so we can detect errors.

Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda: Add AZX_DCAPS_PM_RUNTIME for AMD Raven Ridge

[ Upstream commit 1adca4b0cd65c14cb8b8c9c257720385869c3d5f ]

This patch can make audio controller in AMD Raven Ridge gets runtime
suspended to D3, to save ~1W power when it's not in use.

Cc: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: tm6000: add error handling for dvb_register_adapter

[ Upstream commit e95d7c6eb94c634852eaa5ff4caf3db05b5d2e86 ]

When dvb_register_adapter fails, the lack of error-handling code may
cause unexpected results.

This patch adds error-handling code after calling dvb_register_adapter.

Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
[hans.verkuil@cisco.com: use pr_err and fix typo: adater -> adapter]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/tty: add error handling for pcmcia_loop_config

[ Upstream commit 85c634e919bd6ef17427f26a52920aeba12e16ee ]

When pcmcia_loop_config fails, the lack of error-handling code may
cause unexpected results.

This patch adds error-handling code after calling pcmcia_loop_config.

Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: android: ashmem: Fix mmap size validation

[ Upstream commit 8632c614565d0c5fdde527889601c018e97b6384 ]

The ashmem driver did not check that the size/offset of the vma passed
to its .mmap() function was not larger than the ashmem object being
mapped. This could cause mmap() to succeed, even though accessing parts
of the mapping would later fail with a segmentation fault.

Ensure an error is returned by the ashmem_mmap() function if the vma
size is larger than the ashmem object size. This enables safer handling
of the problem in userspace.

Cc: Todd Kjos <tkjos@android.com>
Cc: devel@driverdev.osuosl.org
Cc: linux-kernel@vger.kernel.org
Cc: kernel-team@android.com
Cc: Joel Fernandes <joel@joelfernandes.org>
Signed-off-by: Alistair Strachan <astrachan@google.com>
Acked-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Reviewed-by: Martijn Coenen <maco@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: omap3isp: zero-initialize the isp cam_xclk{a,b} initial data

[ Upstream commit 2ec7debd44b49927a6e2861521994cc075a389ed ]

The struct clk_init_data init variable is declared in the isp_xclk_init()
function so is an automatic variable allocated in the stack. But it's not
explicitly zero-initialized, so some init fields are left uninitialized.

This causes the data structure to have undefined values that may confuse
the common clock framework when the clock is registered.

For example, the uninitialized .flags field could have the CLK_IS_CRITICAL
bit set, causing the framework to wrongly prepare the clk on registration.
This leads to the isp_xclk_prepare() callback being called, which in turn
calls to the omap3isp_get() function that increments the isp dev refcount.

Since this omap3isp_get() call is unexpected, this leads to an unbalanced
omap3isp_get() call that prevents the requested IRQ to be later enabled,
due the refcount not being 0 when the correct omap3isp_get() call happens.

Fixes: 9b28ee3c9122 ("[media] omap3isp: Use the common clock framework")

Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: soc_camera: ov772x: correct setting of banding filter

[ Upstream commit 22216ec41e919682c15345e95928f266e8ba6f9e ]

The banding filter ON/OFF is controlled via bit 5 of COM8 register.  It
is attempted to be enabled in ov772x_set_params() by the following line.

ret = ov772x_mask_set(client, COM8, BNDF_ON_OFF, 1);

But this unexpectedly results disabling the banding filter, because the
mask and set bits are exclusive.

On the other hand, ov772x_s_ctrl() correctly sets the bit by:

ret = ov772x_mask_set(client, COM8, BNDF_ON_OFF, BNDF_ON_OFF);

The same fix was already applied to non-soc_camera version of ov772x
driver in the commit commit a024ee14cd36 ("media: ov772x: correct setting
of banding filter")

Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: s3c-camif: ignore -ENOIOCTLCMD from v4l2_subdev_call for s_power

[ Upstream commit 30ed2b83343bd1e07884ca7355dac70d25ffc158 ]

When the subdevice doesn't provide s_power core ops callback, the
v4l2_subdev_call for s_power returns -ENOIOCTLCMD.  If the subdevice
doesn't have the special handling for its power saving mode, the s_power
isn't required.  So -ENOIOCTLCMD from the v4l2_subdev_call should be
ignored.

Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: snd-aoa: add of_node_put() in error path

[ Upstream commit 222bce5eb88d1af656419db04bcd84b2419fb900 ]

 Both calls to of_find_node_by_name() and of_get_next_child() return a
node pointer with refcount incremented thus it must be explicidly
decremented here after the last usage. As we are assured to have a
refcounted  np  either from the initial
of_find_node_by_name(NULL, name); or from the of_get_next_child(gpio, np)
in the while loop if we reached the error code path below, an
x of_node_put(np) is needed.

Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: commit f3d9478b2ce4 ("[ALSA] snd-aoa: add snd-aoa")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/extmem: fix gcc 8 stringop-overflow warning

[ Upstream commit 6b2ddf33baec23dace85bd647e3fc4ac070963e8 ]

arch/s390/mm/extmem.c: In function '__segment_load':
arch/s390/mm/extmem.c:436:2: warning: 'strncat' specified bound 7 equals
source length [-Wstringop-overflow=]
  strncat(seg->res_name, " (DCSS)", 7);

What gcc complains about here is the misuse of strncat function, which
in this case does not limit a number of bytes taken from "src", so it is
in the end the same as strcat(seg->res_name, " (DCSS)");

Keeping in mind that a res_name is 15 bytes, strncat in this case
would overflow the buffer and write 0 into alignment byte between the
fields in the struct. To avoid that increasing res_name size to 16,
and reusing strlcat.

Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

alarmtimer: Prevent overflow for relative nanosleep

[ Upstream commit 5f936e19cc0ef97dbe3a56e9498922ad5ba1edef ]

Air Icy reported:

  UBSAN: Undefined behaviour in kernel/time/alarmtimer.c:811:7
  signed integer overflow:
  1529859276030040771 + 9223372036854775807 cannot be represented in type 'long long int'
  Call Trace:
   alarm_timer_nsleep+0x44c/0x510 kernel/time/alarmtimer.c:811
   __do_sys_clock_nanosleep kernel/time/posix-timers.c:1235 [inline]
   __se_sys_clock_nanosleep kernel/time/posix-timers.c:1213 [inline]
   __x64_sys_clock_nanosleep+0x326/0x4e0 kernel/time/posix-timers.c:1213
   do_syscall_64+0xb8/0x3a0 arch/x86/entry/common.c:290

alarm_timer_nsleep() uses ktime_add() to add the current time and the
relative expiry value. ktime_add() has no sanity checks so the addition
can overflow when the relative timeout is large enough.

Use ktime_add_safe() which has the necessary sanity checks in place and
limits the result to the valid range.

Fixes: 9a7adcf5c6de ("timers: Posix interface for alarm-timers")
Reported-by: Team OWL337 <icytxw@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1807020926360.1595@nanos.tec.linutronix.de
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/powernv/ioda2: Reduce upper limit for DMA window size

[ Upstream commit d3d4ffaae439981e1e441ebb125aa3588627c5d8 ]

We use PHB in mode1 which uses bit 59 to select a correct DMA window.
However there is mode2 which uses bits 59:55 and allows up to 32 DMA
windows per a PE.

Even though documentation does not clearly specify that, it seems that
the actual hardware does not support bits 59:55 even in mode1, in other
words we can create a window as big as 1<<58 but DMA simply won't work.

This reduces the upper limit from 59 to 55 bits to let the userspace know
about the hardware limits.

Fixes: 7aafac11e3 "powerpc/powernv/ioda2: Gracefully fail if too many TCE levels requested"
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: wusbcore: security: cast sizeof to int for comparison

[ Upstream commit d3ac5598c5010a8999978ebbcca3b1c6188ca36b ]

Comparing an int to a size, which is unsigned, causes the int to become
unsigned, giving the wrong result.  usb_get_descriptor can return a
negative error code.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
int x;
expression e,e1;
identifier f;
@@

*x = f(...);
... when != x = e1
    when != if (x < 0 || ...) { ... return ...; }
*x < sizeof(e)
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: ibmvscsi: Improve strings handling

[ Upstream commit 1262dc09dc9ae7bf4ad00b6a2c5ed6a6936bcd10 ]

Currently an open firmware property is copied into partition_name variable
without keeping a room for \0.

Later one, this variable (partition_name), which is 97 bytes long, is
strncpyed into ibmvcsci_host_data->madapter_info->partition_name, which is
96 bytes long, possibly truncating it 'again' and removing the \0.

This patch simply decreases the partition name to 96 and just copy using
strlcpy() which guarantees that the string is \0 terminated. I think there
is no issue if this there is a truncation in this very first copy, i.e,
when the open firmware property is read and copied into the driver for the
very first time;

This issue also causes the following warning on GCC 8:

drivers/scsi/ibmvscsi/ibmvscsi.c:281:2: warning:  strncpy  output may be truncated copying 96 bytes from a string of length 96 [-Wstringop-truncation]
...
inlined from  ibmvscsi_probe  at drivers/scsi/ibmvscsi/ibmvscsi.c:2221:7:
drivers/scsi/ibmvscsi/ibmvscsi.c:265:3: warning:  strncpy  specified bound 97 equals destination size [-Wstringop-truncation]

CC: Bart Van Assche <bart.vanassche@wdc.com>
CC: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: klist: Make it safe to use klists in atomic context

[ Upstream commit 624fa7790f80575a4ec28fbdb2034097dc18d051 ]

In the scsi_transport_srp implementation it cannot be avoided to
iterate over a klist from atomic context when using the legacy block
layer instead of blk-mq. Hence this patch that makes it safe to use
klists in atomic context. This patch avoids that lockdep reports the
following:

WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected
 Possible interrupt unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(&(&k->k_lock)->rlock);
                               local_irq_disable();
                               lock(&(&q->__queue_lock)->rlock);
                               lock(&(&k->k_lock)->rlock);
  <Interrupt>
    lock(&(&q->__queue_lock)->rlock);

stack backtrace:
Workqueue: kblockd blk_timeout_work
Call Trace:
 dump_stack+0xa4/0xf5
 check_usage+0x6e6/0x700
 __lock_acquire+0x185d/0x1b50
 lock_acquire+0xd2/0x260
 _raw_spin_lock+0x32/0x50
 klist_next+0x47/0x190
 device_for_each_child+0x8e/0x100
 srp_timed_out+0xaf/0x1d0 [scsi_transport_srp]
 scsi_times_out+0xd4/0x410 [scsi_mod]
 blk_rq_timed_out+0x36/0x70
 blk_timeout_work+0x1b5/0x220
 process_one_work+0x4fe/0xad0
 worker_thread+0x63/0x5a0
 kthread+0x1c1/0x1e0
 ret_from_fork+0x24/0x30

See also commit c9ddf73476ff ("scsi: scsi_transport_srp: Fix shost to
rport translation").

Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James Bottomley <jejb@linux.vnet.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: target/iscsi: Make iscsit_ta_authentication() respect the output buffer size

[ Upstream commit 35bea5c84fd13c643cce63f0b5cd4b148f8c901d ]

Fixes: e48354ce078c ("iscsi-target: Add iSCSI fabric support for target v4.1")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/entry/64: Add two more instruction suffixes

[ Upstream commit 6709812f094d96543b443645c68daaa32d3d3e77 ]

Sadly, other than claimed in:

  a368d7fd2a ("x86/entry/64: Add instruction suffix")

... there are two more instances which want to be adjusted.

As said there, omitting suffixes from instructions in AT&T mode is bad
practice when operand size cannot be determined by the assembler from
register operands, and is likely going to be warned about by upstream
gas in the future (mine does already).

Add the other missing suffixes here as well.

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/5B3A02DD02000078001CFB78@prv1-mh.provo.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: hwmod: RTC: Don't assume lock/unlock will be called with irq enabled

[ Upstream commit 6d609b35c815ba20132b7b64bcca04516bb17c56 ]

When the RTC lock and unlock functions were introduced it was likely
assumed that they would always be called from irq enabled context, hence
the use of local_irq_disable/enable. This is no longer true as the
RTC+DDR path makes a late call during the suspend path after irqs
have been disabled to enable the RTC hwmod which calls both unlock and
lock, leading to IRQs being reenabled through the local_irq_enable call
in omap_hwmod_rtc_lock call.

To avoid this change the local_irq_disable/enable to
local_irq_save/restore to ensure that from whatever context this is
called the proper IRQ configuration is maintained.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>