Dan Carpenter [Wed, 24 Mar 2010 11:56:41 +0000 (14:56 +0300)]
mac80211: remove unneed variable from ieee80211_tx_pending()
We don't need "sdata" any more after:
d84f323477260e773d5317ad7cbe50f76115cb47
mac80211: remove dev_hold/put calls
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Wed, 24 Mar 2010 08:11:14 +0000 (10:11 +0200)]
cfg80211: Improve connection quality maintenance docs in nl80211.h
In nl80211.h, be a little more elaborate in the docs for the definitions
NL80211_ATTR_CQM_RSSI_THOLD and NL80211_ATTR_CQM_RSSI_HYST.
Reported-by: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Tue, 23 Mar 2010 07:02:34 +0000 (09:02 +0200)]
mac80211: Add support for connection quality monitoring
Add support for the set_cqm_config op. This op function configures the
requested connection quality monitor rssi threshold and rssi hysteresis
values to the hardware if the hardware supports
IEEE80211_HW_SUPPORTS_CQM.
For unsupported hardware, currently -EOPNOTSUPP is returned, so the mac80211
is currently not doing connection quality monitoring on the host. This could be
added later, if needed.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Tue, 23 Mar 2010 07:02:33 +0000 (09:02 +0200)]
cfg80211: Add connection quality monitoring support to nl80211
Add support for basic configuration of a connection quality monitoring to the
nl80211 interface, and basic support for notifying about triggered monitoring
events.
Via this interface a user-space connection manager may configure and receive
pre-warning events of deteriorating WLAN connection quality, and start
preparing for roaming in advance, before the connection is already lost.
An example usage of such a trigger is starting scanning for nearby AP's in
an attempt to find one with better connection quality, and associate to it
before the connection characteristics of the existing connection become too bad
or the association is even lost, leading in a prolonged delay in connectivity.
The interface currently supports only RSSI, but it could be later extended
to include other parameters, such as signal-to-noise ratio, if need for that
arises.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Fri, 26 Feb 2010 01:16:36 +0000 (17:16 -0800)]
libertas: add auto auth mode feature
Auto auth mode is enabled by default. If user doesn't specify the
auth mode, while association driver will first try with open mode
and then with shared key mode. If user specifies an auth mode,
auto auth is disabled and driver will not try association with
another auth mode.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 24 Mar 2010 08:12:13 +0000 (13:42 +0530)]
ath9k_htc: Fix symbol collision with ath9k
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Ngu [Mon, 22 Mar 2010 11:52:44 +0000 (00:52 +1300)]
drivers/net/wireless/b43/main.c:4351: Fixed coding style
WARNING: braces {} are not necessary for any arm of this statement
Signed-off-by: Daniel Ngu <daniel.dy.ngu@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 19 Mar 2010 05:14:53 +0000 (07:14 +0200)]
mac80211: Add support for connection monitor in hardware
This patch is based on a RFC patch by Kalle Valo.
The wl1271 has a feature which handles the connection monitor logic
in hardware, basically sending periodically nullfunc frames and reporting
to the host if AP is lost, after attempting to recover by sending
probe-requests to the AP.
Add support to mac80211 by adding a new flag IEEE80211_HW_CONNECTION_MONITOR
which prevents conn_mon_timer from triggering during idle periods, and
prevents sending probe-requests to the AP if beacon-loss is indicated by the
hardware.
Cc: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Fri, 19 Mar 2010 01:29:40 +0000 (18:29 -0700)]
drivers/net/wireless/ray_cs.c: Use iw_handler function prototypes
Change local functions that are cast to iw_handler to
the more standard use with "union iwreq_data *wrqu"
so the iw_handler array no longer needs the casts.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Fri, 19 Mar 2010 01:29:39 +0000 (18:29 -0700)]
orinoco/wext.c: Remove local #define STD_IW_HANDLER
Use IW_HANDLER from wireless.h instead
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Fri, 19 Mar 2010 01:29:38 +0000 (18:29 -0700)]
drivers/net: Remove local #define IW_IOCTL, use IW_HANDLER
Use #define IW_HANDLER from wireless.h instead
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Fri, 19 Mar 2010 01:29:37 +0000 (18:29 -0700)]
drivers/net/wireless: Use IW_HANDLER macro
Convert direct uses of [ (foo - SIOCIWFIRST) , fn)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Fri, 19 Mar 2010 01:29:36 +0000 (18:29 -0700)]
net/wireless/wext-core.c: Use IW_EVENT_IDX macro
There's a wireless.h macro for this, might as well use it.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Fri, 19 Mar 2010 01:29:35 +0000 (18:29 -0700)]
net/wireless/wext_core.c: Use IW_IOCTL_IDX macro
There's a wireless.h macro for this, might as well use it.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Fri, 19 Mar 2010 01:29:33 +0000 (18:29 -0700)]
wireless.h: Use SIOCIWFIRST not SIOCSIWCOMMIT for range check
These two #defines use the same value, but
SIOCIWFIRST makes more sense in this use.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Fri, 19 Mar 2010 01:29:32 +0000 (18:29 -0700)]
include/linux/wireless.h: Add IW_HANDLER macro to initialize array entry
Copied the idea from orinoco
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Teemu Paasikivi [Thu, 18 Mar 2010 10:26:46 +0000 (12:26 +0200)]
wl1271: Changed platform_device to be dynamically allocated
Changed platform_device to be allocated dynamically from the
wl1271_alloc_hw function. Also cleaned up error handling in the
wl1271_alloc_hw function and module probe functions.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Mar 2010 10:26:45 +0000 (12:26 +0200)]
wl1271: Remove circular interlocking related to the inetaddr notifier chain
Removing the wl1271 from the inet addr notifier chain sometimes causes the
registered handler to be called - causing locking problems if the removing
function is called from within the mutex.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Mar 2010 10:26:44 +0000 (12:26 +0200)]
wl1271: Don't generate null func template for ad-hoc
The null func template is not needed for ad-hoc, and it's generation is not
supported for ad-hoc (mac80211 will WARN about it.)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Mar 2010 10:26:43 +0000 (12:26 +0200)]
wl1271: Update filters properly
This patch adds support for the filters configured by the mac80211 stack.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Teemu Paasikivi [Thu, 18 Mar 2010 10:26:42 +0000 (12:26 +0200)]
wl1271: Removed duplicate code from module remove function.
Removed duplicate code from wl1271_sdio module remove function. For
freeing stuff in the remove function wl1271_free_hw function is now
used.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Teemu Paasikivi [Thu, 18 Mar 2010 10:26:41 +0000 (12:26 +0200)]
wl1271: Added DEBUG_SDIO flag
Added separate flag for SDIO debugging. Previously it has used
DEBUG_SPI flag. This patch also includes couple indentation fixes.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Mar 2010 10:26:40 +0000 (12:26 +0200)]
wl1271: Remove deprecated interface config function
It's no longer needed.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Mar 2010 10:26:39 +0000 (12:26 +0200)]
wl1271: Fix MAC address handling
This patch fixes MAC address handling. To achieve this, firmware booting had
to be delayed from the previous op_start to op_add_interface, which is the point
when the driver gets to know the configured MAC address. As the wl1271 only
supports one virtual interface, this even seems quite logical.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Thu, 18 Mar 2010 10:26:38 +0000 (12:26 +0200)]
wl1271: enable U-APSD
wl1271 supports U-APSD similarly as wl1251, so let's enable it.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Thu, 18 Mar 2010 10:26:37 +0000 (12:26 +0200)]
wl1271: fix ps scheme in wl1271_op_conf_tx()
Commit "wl1271: implement WMM" accidentally used CONF_PS_SCHEME_LEGACY_PSPOLL,
but instead CONF_PS_SCHEME_LEGACY should be used as earlier.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Thu, 18 Mar 2010 10:26:36 +0000 (12:26 +0200)]
wl1271: create qos nullfunc template
Needed for U-APSD.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Thu, 18 Mar 2010 10:26:35 +0000 (12:26 +0200)]
wl1271: get probe request template from mac80211
If we get probe request from mac80211, we can remove two functions.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Thu, 18 Mar 2010 10:26:34 +0000 (12:26 +0200)]
wl1271: get pspoll and nullfunc templates from mac80211
mac80211 now can create pspoll and nullfunc templates, better to use those.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Thu, 18 Mar 2010 10:26:33 +0000 (12:26 +0200)]
wl1271: enable WMM
Everything is ready now and we can enable WMM in wl1271.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Mar 2010 10:26:32 +0000 (12:26 +0200)]
wl1271: Add sysfs file to control BT co-ex state
Add a sysfs file to control the state of the BT co-ex (enable or disable it.)
By default, the BT co-ex is enabled.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Mar 2010 10:26:31 +0000 (12:26 +0200)]
wl1271: Move platform device registration from _spi to _main
In order to get the platform device for both SPI and SDIO, move the platform
device registration to wl1271_main.c from wl1271_spi.c.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Mar 2010 10:26:30 +0000 (12:26 +0200)]
wl1271: Add proper WLAN-BT co-ex configuration, and enable co-ex.
Add configuration values for the varous WLAN-BT co-ex configuration parameters,
and finally enable WLAN-BT co-ex. Based on preliminary measurements, it
appears the co-ex feature is not increasing WLAN power consumption, if BT
is not activated.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Mar 2010 10:26:29 +0000 (12:26 +0200)]
wl1271: Fix SG configuration message structures
The bluetooth coexistence (SG) configuration messages have changed and
were completely wrong. For instance, intending to enable the SG, it was
instead disabled.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Teemu Paasikivi [Thu, 18 Mar 2010 10:26:28 +0000 (12:26 +0200)]
wl1271: Changed SDIO MMC host claiming
Changed driver to keep MMC host claimed while wlan interface is up.
This keeps MMC stack from powering the SDIO device down.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Teemu Paasikivi [Thu, 18 Mar 2010 10:26:27 +0000 (12:26 +0200)]
wl1271: Cleaned up wlan power on/off functions
Added method for wlan power control to io_ops struct and moved
wl1271_power_on and wl1271_power_off functions to wl1271_io.h.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Mar 2010 10:26:26 +0000 (12:26 +0200)]
wl1271: Fix configuration of the TX opportunity value
The per-queue TX opportunity value is configured by the mac80211 in units
of 32us. The firmware however wants it in us, so add the conversion.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:25 +0000 (14:25 +0530)]
ath9k_htc: Support for AR9271 chipset.
Features:
* Station mode
* IBSS mode
* Monitor mode
* Legacy support
* HT support
* TX/RX 11n Aggregation
* HW encryption
* LED
* Suspend/Resume
For more information: http://wireless.kernel.org/en/users/Drivers/ath9k_htc
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:24 +0000 (14:25 +0530)]
ath9k_hw: fix hardware deinit
Without this you will get a panic if the device initialization
fails. Also, free ath_hw instance properly. ath9k_hw_deinit()
shouldn't do it.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:23 +0000 (14:25 +0530)]
ath9k_hw: add HTC init hardware call for special resets for AR9271
AR9271 needs a full reset only upon the first reset, add
a call for the driver to enable these special resets. We
can optimize this out later without an export.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:22 +0000 (14:25 +0530)]
ath9k_hw: always set the core clock for AR9271
When initializing the PLL on AR9271 we always need
to set the core clock to 117MHz. While at it remove
the baud rate settings for the serial device on the
AR9271, the default settings work well unless you
want to customize it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:21 +0000 (14:25 +0530)]
ath9k_hw: use the skip count for PA calibration on AR9271
Periodic power amplifier offset calibration is skipped on ath9k
algorithmically, this is required on AR9271.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:20 +0000 (14:25 +0530)]
ath9k_hw: restrict valid nf readings for AR9271 to -114
Noisefloor values read on AR9271 are unreliable if they
are less than -114, set those statically to -116.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:19 +0000 (14:25 +0530)]
ath9k_hw: fix noisefloor history buffer usage on AR9271
Noisefloor calibration involves querying hardware for samples
and storing this information on a history buffer in hardware for
actual noisefloor calibration processing in hardware. The history
buffer supports collecting information for all Atheros hardware,
one history buffer slot for each chain on each channel used for
MIMO operation. For current hardware this means one history
buffer slot for each chain on both the control (or primary) channel
and the extension (or secondary) channel. We know which noisefloor
registers to poke for collecting noisefloor data through the
chainmask.
For AR9285 and AR9271 devices, both 1x1, the chaimmask is defined as
0x9 =
0b0001001. The first four bits represent each chain out of
a maximum of 4 chains [0-3] on the primary channel. The last four
bits represent each chain on the extension channel. A chainmask
of 0x9 therefore indicates chain 1 is active on both the primary
and the extension channel.
AR9271 only requires collecting and storing noisefloor history buffer
data for the first chain on both the control and extension channel
(nfarray[0] and nfarray[3]) so fix the code and avoid which reads
and writes to the history buffer for the other chains.
Since the noisefloor varies depending on the number of chains your
device supports also initialize the noisefloor history buffer with
reasonable values seen on 1x1 devices such as AR9285.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:18 +0000 (14:25 +0530)]
ath9k_hw: Fix full sleep setup for AR9271
After telling the AR9271 to go into full sleep we do not need
to clear the RTC reset signal.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:17 +0000 (14:25 +0530)]
ath9k_hw: fix TX descriptor setup for AR9271
The TX descriptors setup for AR971 requires the same
setup as AR9285, so use that.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:16 +0000 (14:25 +0530)]
ath9k_hw: skip chip tests for AR9271
The chip test is not required for AR9271 on the host driver
code as the firmware will do the test internally on its own.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:15 +0000 (14:25 +0530)]
ath9k_hw: add GPIO setup code for AR9271
Assign the proper number of GPIO pins for AR9271.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:14 +0000 (14:25 +0530)]
ath9k_hw: update initialization values for AR9271
Update the register initialization values for AR9271.
This is based on our last review from our systems team.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ming Lei [Mon, 1 Mar 2010 15:13:29 +0000 (23:13 +0800)]
ath9k: decrease size of ath9k.ko
From
e74b075cdb143d45be9b371ee8a8e2dcfc15ab34 Mon Sep 17 00:00:00 2001
From: Ming Lei <tom.leiming@gmail.com>
Date: Sat, 27 Feb 2010 23:50:54 +0800
Subject: [PATCH] ath9k: decrease size of ath9k.ko
The patch defines the fields of 'valid_single_stream' and 'valid' in
struct ath_rate_table as char type, so decrease the size of ath9k.ko
about 2KB.
old ath9k.ko
[tom@tom-lei ath9k]$ size ath9k.ko
text data bss dec hex filename
69344 3080 168 72592 11b90 ath9k.ko
new ath9k.ko
[tom@tom-lei ath9k]$ size ath9k.ko
text data bss dec hex filename
67304 3080 168 70552 11398 ath9k.ko
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 23 Mar 2010 20:46:43 +0000 (16:46 -0400)]
Merge branch 'wireless-next-2.6' of git://git./linux/kernel/git/iwlwifi/iwlwifi-2.6
Wey-Yi Guy [Fri, 5 Mar 2010 22:22:46 +0000 (14:22 -0800)]
iwlwifi: code cleanup for connectivity recovery
Split the connectivity check and recovery routine into separated
functions based on the types
1. iwl_good_ack_health() - check for ack count
2. iwl_good_plcp_health() - check for plcp error
Based on the type of errors being detected, different recovery methods
will be used to bring the system back to normal operational state.
Because different NIC has different HW and uCode, the behavior is also
different; these functions thus now form part of the ops infrastructure,
so we can have more control on how to monitor and recover from error condition
case per device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy [Thu, 4 Mar 2010 21:38:59 +0000 (13:38 -0800)]
iwlwifi: Recover TX flow failure
Monitors the tx statistics to detect the drop in throughput.
When the throughput drops, the ratio of the actual_ack_count and the
expected_ack_count also drops. At the same time, the aggregated
ba_timeout (the number of ba timeout retries) also rises. If the
actual_ack_count/expected_ack_count ratio is 0 and the number of ba
timeout retries rises to BA_TIMEOUT_MAX, no tx packets can be delivered.
Reloading the uCode and bring the system back to normal operational
state.
Signed-off-by: Trieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy [Thu, 4 Mar 2010 21:38:58 +0000 (13:38 -0800)]
iwlwifi: move plcp check to separated function
Move the plcp error checking into stand alone function and pointed by ops
to accommodate devices not needing this recovery.
Signed-off-by: Trieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy [Tue, 2 Mar 2010 01:23:50 +0000 (17:23 -0800)]
iwlwifi: Recover TX flow stall due to stuck queue
Monitors the internal TX queues periodically. When a queue is stuck
for some unknown conditions causing the throughput to drop and the
transfer is stop, the driver will force firmware reload and bring the
system back to normal operational state.
The iwlwifi devices behave differently in this regard so this feature is
made part of the ops infrastructure so we can have more control on how to
monitor and recover from tx queue stall case per device.
Signed-off-by: Trieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Shanyu Zhao [Sat, 6 Mar 2010 01:05:20 +0000 (17:05 -0800)]
iwlwifi: clean up driver names for 1000/5000/6000
Align the driver names with official product names for 1000/5000/6000
series. This change mainly affects the debug messages show up in system
log. No functional changes.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Thu, 21 Jan 2010 15:07:44 +0000 (07:07 -0800)]
iwlwifi: sta_id cannot be invalid in rs_initialize_lq
The only caller of this is iwl_rs_rate_init
which is only called with a valid sta_id.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reinette Chatre [Tue, 23 Feb 2010 00:24:47 +0000 (16:24 -0800)]
iwlwifi: implement new mac80211 station add/remove calls
mac80211 recently implemented two new callbacks that are used to request
station add/remove from the driver. The benefot from these new callbacks
are that they enable the driver to sleep while performing this work.
This is a big patch since a few things need to be coordinated in this move.
First we need to decouple station management from rate scaling, which
caused a lot of code to be moved and/or deleted. Next we needed to tie in
with mac80211's station management callback and let it direct our station
management as well as trigger the rate scaling initialization.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reinette Chatre [Fri, 19 Feb 2010 06:58:32 +0000 (22:58 -0800)]
iwlwifi: only add broadcast station once
Currently the broadcast station is added after every RXON command. Change
this to only add the broadcast station when interface is added by mac80211.
With this we need some extra work to ensure broadcast station is always
present since station table is cleared when RXON without ASSOC bit set is
sent. To deal with this we re-add all driver known stations to uCode after
such an RXON command is sent.
We also do some cleanup and remove the various calls to clear the station
table. We now only clear the station table in two scenarios:
- only clear uCode portion of station table when RXON command without ASSOC
bit is sent
- clear uCode and driver portion when interface goes down or is removed.
We need to do this clearing when interface goes down to deal with the
device restart/reconfigure routines which do not remove the interface, but
do add the interface during reconfiguration.
Previously the keys were also cleared when station table in driver is
cleared, this is not done anymore since mac80211 will take care that keys
are set and cleared correctly.
There is a known issue with this change. Associating with different AP
without bringing interface down fails with a firmware error. This is
because of the lack of full station notification support and the later
patches in this series that complete the station notification support will
fix this.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Ben Cahill [Tue, 2 Mar 2010 20:48:25 +0000 (12:48 -0800)]
iwlagn: Add Flow-handler (FH) register dump for 4965.
FH register dump debug feature was recently added for 5000 and later;
4965 can use it also.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
florian@mickler.org [Sat, 13 Mar 2010 12:31:05 +0000 (13:31 +0100)]
rename new rfkill sysfs knobs
This patch renames the (never officially released) sysfs-knobs
"blocked_hw" and "blocked_sw" to "hard" and "soft", as the hardware vs
software conotation is misleading.
It also gets rid of not needed locks around u32-read-access.
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Wed, 3 Mar 2010 09:45:42 +0000 (18:45 +0900)]
mac80211: (really) fix rates setup on IBSS merge
when an IBSS merge happened, the supported rates for the newly added station
were left empty, causing the rate control module to be initialized with only
the basic rates.
the section of the ibss code which deals with updating supported rates for
an already existing station failed to inform the rate control module about the
new rates. as both minstrel and pid don't have an update function i just use
the init function.
also remove unnecessary (unsigned long long) casts and edit debug message.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 16 Mar 2010 19:02:35 +0000 (15:02 -0400)]
Revert "mac80211: fix rates setup on IBSS merge"
I accidentally merged an incomplete version of the patch...
This reverts commit
b4d59a9317e41faec3d0b6a03f0454d1e8abb710.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alban Browaeys [Sun, 28 Feb 2010 16:14:40 +0000 (17:14 +0100)]
rt2x00: Fix TX status reporting for rt2800pci.
After testing, we found that TX_STA_FIFO_MCS is the last MCS value
tried. If the transmission failed, 8 frames have been transmitted. If the
transmission succeed, we can easily compute the number of retry. This patch fix
the way status is reported to mac80211 rate control. It has 2 bugs :
1. mcs can contain the short preamble flag and it will lead to wrong
computations.
2. minstrel nearly always say that 54 Mbits is the best rate, even if we are
very far from the AP
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alban Browaeys [Fri, 26 Feb 2010 22:19:59 +0000 (23:19 +0100)]
rt2x00: txdone implementation supporting hw encryption.
This is an implementation that support WCID being the encryption key.
Wireless Cli Id was set to be the encryption key in rt2800pci_write_tx_desc
and read (TX_STA_FIFO_WCID) as the current queue entry index.
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Mon, 15 Mar 2010 16:22:26 +0000 (17:22 +0100)]
rt2x00: fix warning when building rt2800pci with just soc support
Fix compile warning "rt2800pci.c:1248: warning: 'rt2800pci_device_table'
defined but not used" when building rt2800pci with only soc support
(without pci).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Roskin [Fri, 12 Mar 2010 05:01:22 +0000 (00:01 -0500)]
ipw2x00: replace "ieee80211" with "libipw" where appropriate
"ieee80211" was the old name of the common library for ipw2100 and
ipw2200. It was renamed to "libipw", but some occurrences of the old
name remained.
Rename alloc_ieee80211() to alloc_libipw() and free_ieee80211() to
free_libipw(). Adjust comments and label names. Change prefixes in
diagnostic messages.
Keep /proc/net/ieee80211 under the original name to avoid breaking user
interface.
Move the affected EXPORT_SYMBOL macros to their proper places.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Roskin [Fri, 12 Mar 2010 04:13:28 +0000 (23:13 -0500)]
orinoco: disable support for prism chipset by default
The hostap driver provides better support for Prism chipset.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Grazvydas Ignotas [Thu, 11 Mar 2010 15:45:07 +0000 (17:45 +0200)]
wl1251: reduce eeprom read wait time
4sec wait is way too pessimistic, TI driver uses 40ms here,
and testing shows that is ebough, so let's also use that.
While at it, add useful sounding comment from the TI driver.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Grazvydas Ignotas [Thu, 11 Mar 2010 15:44:57 +0000 (17:44 +0200)]
wl1251: fix ELP_CTRL register accesses when using SDIO
For some unknown reason ELP_CTRL can't be accesed using
sdio_memcpy_* functions (any attemts to do so result in timeouts):
wl1251: ERROR sdio write failed (-110)
wl1251: ERROR sdio read failed (-110)
wl1251: WARNING WLAN not ready
To fix this, add special IO functions for ELP_CTRL access that are
using sdio_readb/sdio_writeb. Similar handling is done in TI
reference driver from Android code drop.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Bob Copeland <me@bobcopeland.com>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Grazvydas Ignotas [Fri, 12 Mar 2010 10:28:41 +0000 (12:28 +0200)]
wl1251: make local symbols static
Make local functions and data static, also constify
some structures. While at it, clean up unneeded includes.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Bob Copeland <me@bobcopeland.com>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 11 Mar 2010 15:28:24 +0000 (16:28 +0100)]
mac80211: optimize tx status processing
When a cooked monitor interface is active, ieee80211_tx_status()
generates a radiotap header for every single frame, even if it wasn't
injected and thus won't be sent to a monitor interface.
This patch reduces cpu utilization by moving the cooked monitor check a
bit earlier, before it generates the rtap header.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stewart Malik [Thu, 11 Mar 2010 09:58:29 +0000 (20:28 +1030)]
DRIVER: Libertas: Fixed coding style in rx.c
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 10 Mar 2010 16:08:50 +0000 (11:08 -0500)]
ath5k: remove unused beacon timer code
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 10 Mar 2010 16:08:49 +0000 (11:08 -0500)]
ath5k: remove dead source in ath5k_combine_linear_pcdac_curves
This code was commented-out when it was added about a year ago and
remains unchanged -- seems as if we don't need it...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 10 Mar 2010 16:08:48 +0000 (11:08 -0500)]
ath5k: remove some dead functions
"ath5k: remove stale function declarations, make some functions static"
commented-out some unused functions. This removes them.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
matthieu castet [Sun, 28 Feb 2010 14:42:54 +0000 (15:42 +0100)]
airo : Print of firmware version
For the firmware version 5.30.17 the log file shows:
Firmware version 5.30.11
The variable softSubVer is binary.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Jose Alonso <joalonsof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
matthieu castet [Sun, 28 Feb 2010 14:31:21 +0000 (15:31 +0100)]
airo : fix printing status info
For some status, reason is encoded in the low byte, but airo_print_status forgot tp mask low byte in status parsing.
This make it only work when reason is 0.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Wed, 10 Mar 2010 16:41:32 +0000 (10:41 -0600)]
ssb: Export ssb_chipco_gpio_control - needed by N PHY code
The latest changes in the N PHY core require the symbol
ssb_chipco_gpio_control to be exported.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andrew Blaich [Mon, 1 Mar 2010 15:30:40 +0000 (10:30 -0500)]
ath5k: fixing retries in ath5k_hw_setup_4word_tx_desc
The rate control algorithm, default is Minstrel for ath5k, determines
the number of retries to use for each rate. However, there exists in
ath5k_hw_setup_4word_tx_desc (which is called for AR5212 like devices)
a set number of retries defined by AR5K_TUNE_HWTXTRIES. The set
number of tries is added to the tx_tries0 variable setup by the rate
control algorithm. This changes the number of retries the rate
control algorithm considers necessary. By removing the
AR5K_TUNE_HWTXTRIES from the retry calculation the rate control
algorithm is given control over the number of retries.
Signed-off-by: Andrew Blaich <ablaich@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 1 Mar 2010 12:32:11 +0000 (13:32 +0100)]
ath9k: fix rate control tx status handling for A-MPDU
Currently the rate control tx status update gets called for every
subframe of an A-MPDU, and ath9k marks the frame with the relevant
status update with an internal flag. This not suitable for rate control
algorithms using the standard mac80211 rate control API, so fix this by
using IEEE80211_TX_STAT_AMPDU for marking the correct frames that
should be processed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Teemu Paasikivi [Wed, 10 Mar 2010 11:22:31 +0000 (13:22 +0200)]
wl1271: Changed wl1271_sdio to be selectable only on ARM
As wl1271_sdio implementation depends on ARM GPIO impelementation it is
not directly usable on other architectures at the moment. Added
ARM dependency to kernel configuration option.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Tue, 9 Mar 2010 07:56:21 +0000 (16:56 +0900)]
ath5k: Minor EEPROM documentation updates
Here are some minor updates for EEPROM, mostly documentation and some small
fixes which have no effect at the moment.
- fixed_bias is not available for B mode.
- AR5K_EEPROM_[RT]X_CHAIN_DIS is 3 bit. this is MIMO and will not be used in
ath5k, but just to be correct.
- AR5K_EEPROM_JAP_MID_EN added, and shift of following flags adapted.
- added some documentation for EEPROM values and some comments.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Tue, 9 Mar 2010 07:56:15 +0000 (16:56 +0900)]
ath5k: IQ calibration for AR5211 is slightly different
according to the HAL sources the calculation of the Q value is slightly
different for AR5211 chips.
i couldn't test this since IQ calibration never finishes on older parts. this
is a different problem...
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Tue, 9 Mar 2010 07:56:00 +0000 (16:56 +0900)]
ath5k: add debugfs file frameerrors
add a debugfs file to see different RX and TX errors as reported in our status
descriptors. this can help to diagnose driver problems.
statistics can be cleared by writing 'clear' into the frameerrors file.
example:
# cat /sys/kernel/debug/ath5k/phy0/frameerrors
RX
---------------------
CRC 27 (11%)
PHY 3 (1%)
FIFO 0 (0%)
decrypt 0 (0%)
MIC 0 (0%)
process 0 (0%)
jumbo 0 (0%)
[RX all 245]
TX
---------------------
retry 2 (9%)
FIFO 0 (0%)
filter 0 (0%)
[TX all 21]
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Tue, 9 Mar 2010 07:55:55 +0000 (16:55 +0900)]
ath5k: remove ah_gpio_npins
it's never used and we have a newer implementation in gpio.c.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Tue, 9 Mar 2010 07:55:49 +0000 (16:55 +0900)]
ath5k: remove ah_mac_revision
it's not used, and we have ah_mac_srev.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Tue, 9 Mar 2010 07:55:44 +0000 (16:55 +0900)]
ath5k: remove ah_magic
it's never used. probably a leftover from the old OpenHAL days...
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Tue, 9 Mar 2010 07:55:38 +0000 (16:55 +0900)]
ath5k: remove double opmode definition
opmode (operating mode) was defined in struct ath5k_hw and struct ath5k_softc.
remove it from ath5k_hw and use only from ath5k_softc (sc->opmode).
(btw: what's the meaning of opmode when we have multiple interfaces?)
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Tue, 9 Mar 2010 07:55:28 +0000 (16:55 +0900)]
ath5k: preserve antenna settings
save antenna settings and preserve across resets.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Tue, 9 Mar 2010 07:55:17 +0000 (16:55 +0900)]
ath5k: add antenna statistics and debugfs file for antenna settings
keep statistics about which antenna was used for TX and RX. this is used only
for debugging right now, but might have other applications later.
add a new file 'antenna' in debugfs (/sys/kernel/debug/ath5k/phy0/antenna) to show
antenna use statistics and antenna diversity related register values. it can
also be used to set the antenna mode until we have proper support for that in
iw:
- echo diversity > antenna: use default antenna mode (RX and TX diversity)
- echo fixed-a > antenna: use fixed antenna A for RX and TX
- echo fixed-b > antenna: use fixed antenna B for RX and TX
- echo clear > antenna: reset antenna statistics
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Thu, 4 Mar 2010 16:27:36 +0000 (18:27 +0200)]
rndis_wlan: Implement cfg80211 PMKSA API
Add support for cfg80211 set_pmksa/del_pmksa/flush_pmksa. Updating PMKID
entry list is done on driver side since NDIS API requires full list update.
v2:
- fixed to use new netdev_dbg/warn/etc instead of old devdbg/warn/etc
- fixed false padding from struct ndis_80211_bssid_info
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Thu, 4 Mar 2010 16:27:24 +0000 (18:27 +0200)]
rndis_wlan: get max_num_pmkids from device
Extend rndis_wlan_get_caps() to get 802.11 capabilities and maximum
supported number of PMKIDs by device.
v2: fixed to use new netdev_dbg/warn/etc instead of old devdbg/warn/etc
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Thu, 4 Mar 2010 16:27:12 +0000 (18:27 +0200)]
rndis_wlan: remove unused variables from priv structure
Some variables were left unused after cfg80211 conversion. Remove those and related deadcode.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Thu, 4 Mar 2010 16:27:02 +0000 (18:27 +0200)]
rndis_wlan: copy only useful data from rndis_command respond
rndis_query_oid() uses full output buffer size to copy response buffer
from rndis_command()/device. This doesn't cause problems as response buffer
is sized based on output buffer but does copy extra unset bytes.
So change rndis_query_oid() so that only meaningful bytes are being copied.
Also in case of malfunctioning device/cable/etc returned data offset from
device might be wrong so bound check memory access correctly, so add
checks for this.
v2: fixed to use new netdev_dbg/warn/etc instead of old devdbg/warn/etc
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 1 Mar 2010 21:21:40 +0000 (22:21 +0100)]
minstrel: make the rate control ops reusable from another rc implementation
This patch makes it possible to reuse the minstrel rate control ops
from another rate control module. This is useful in preparing for the
new 802.11n implementation of minstrel, which will reuse the old code
for legacy stations.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 1 Mar 2010 21:17:38 +0000 (22:17 +0100)]
minstrel: simplify and fix debugfs code
This patch cleans up the debugfs read function for the statistics by
using simple_read_from_buffer instead of its own semi-broken hack.
Also removes a useless member of the minstrel debugfs info struct.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Benoit Papillault [Sat, 27 Feb 2010 22:05:26 +0000 (23:05 +0100)]
ath5k: Fix TX/RX padding for all frames
Currently, the padding position is based on
ieee80211_get_hdrlen_from_skb(). This is not correct since the HW does
padding on RX (and expect the same padding to be present on TX) at the
following position :
- management : 24 + 6 if 4-addr format
- control : 24 + 6 if 4-addr format
- data : 24 + 6 if 4-addr format + 2 if QoS
- invalid : 24 + 6 if 4-addr format
whereas ieee80211_get_hdrlen_from_skb() is :
- management : 24
- control : 16 except for ACK/CTS where it is 10
- data : 24 + 6 if 4-addr format + 2 if QoS + 2 if QoS & order
- invalid : 24
So, correct frames are not affected : management frames do not use
4-addr format, control frames have no body and invalid frames are ...
not valid by definition. However, in order to use monitor interface for
debugging purpose, one must be able to send/receive any frames, be it
correct or not. Such frames are affected by incorrect padding.
Moreover, since padding is added on TX, we need to remove it before
calling ieee80211_tx_status. This affect TX packets received by monitor
interfaces.
It has been tested between an ath5k based card (AR5212) and an ar9170usb
based card (netgear WNDA3100) using a frame generator and a monitor
interface for each card.
v2: Added ath5k_add_padding / ath5k_remove_padding
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andres Salomon [Fri, 26 Feb 2010 00:18:47 +0000 (19:18 -0500)]
mac80211: give warning if building w/out rate ctrl algorithm
I discovered that if EMBEDDED=y, one can accidentally build a mac80211 stack
and drivers w/ no rate control algorithm. For drivers like RTL8187 that don't
supply their own RC algorithms, this will cause ieee80211_register_hw to
fail (making the driver unusable).
This will tell kconfig to provide a warning if no rate control algorithms
have been selected. That'll at least warn the user; users that know that
their drivers supply a rate control algorithm can safely ignore the
warning, and those who don't know (or who expect to be using multiple
drivers) can select a default RC algorithm.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Thu, 25 Feb 2010 06:15:31 +0000 (14:15 +0800)]
iwmc3200wifi: typo fix and code cleanup
Fix wrong IWM_RX_TICKET_DROP_REASON_MSK macro define, typo and other
small cleanups.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / GitHub / moto-9609 / android_kernel_motorola_exynos9610.git / log