mm: vmscan: improve comment on low-page cache handling

Fix comment style and elaborate on why anonymous memory is force-scanned
when file cache runs low.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Satoru Moriya <satoru.moriya@hds.com>
Cc: Simon Jeons <simon.jeons@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: vmscan: clarify how swappiness, highest priority, memcg interact

A swappiness of 0 has a slightly different meaning for global reclaim
(may swap if file cache really low) and memory cgroup reclaim (never
swap, ever).

In addition, global reclaim at highest priority will scan all LRU lists
equal to their size and ignore other balancing heuristics.  UNLESS
swappiness forbids swapping, then the lists are balanced based on recent
reclaim effectiveness.  UNLESS file cache is running low, then anonymous
pages are force-scanned.

This (total mess of a) behaviour is implicit and not obvious from the
way the code is organized.  At least make it apparent in the code flow
and document the conditions.  It will be it easier to come up with sane
semantics later.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Satoru Moriya <satoru.moriya@hds.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Simon Jeons <simon.jeons@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: vmscan: save work scanning (almost) empty LRU lists

In certain cases (kswapd reclaim, memcg target reclaim), a fixed minimum
amount of pages is scanned from the LRU lists on each iteration, to make
progress.

Do not make this minimum bigger than the respective LRU list size,
however, and save some busy work trying to isolate and reclaim pages
that are not there.

Empty LRU lists are quite common with memory cgroups in NUMA
environments because there exists a set of LRU lists for each zone for
each memory cgroup, while the memory of a single cgroup is expected to
stay on just one node.  The number of expected empty LRU lists is thus

  memcgs * (nodes - 1) * lru types

Each attempt to reclaim from an empty LRU list does expensive size
comparisons between lists, acquires the zone's lru lock etc.  Avoid
that.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Satoru Moriya <satoru.moriya@hds.com>
Cc: Simon Jeons <simon.jeons@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcg: only evict file pages when we have plenty

Commit e9868505987a ("mm, vmscan: only evict file pages when we have
plenty") makes a point of not going for anonymous memory while there is
still enough inactive cache around.

The check was added only for global reclaim, but it is just as useful to
reduce swapping in memory cgroup reclaim:

    200M-memcg-defconfig-j2

                                     vanilla                   patched
    Real time              454.06 (  +0.00%)         453.71 (  -0.08%)
    User time              668.57 (  +0.00%)         668.73 (  +0.02%)
    System time            128.92 (  +0.00%)         129.53 (  +0.46%)
    Swap in               1246.80 (  +0.00%)         814.40 ( -34.65%)
    Swap out              1198.90 (  +0.00%)         827.00 ( -30.99%)
    Pages allocated   16431288.10 (  +0.00%)    16434035.30 (  +0.02%)
    Major faults           681.50 (  +0.00%)         593.70 ( -12.86%)
    THP faults             237.20 (  +0.00%)         242.40 (  +2.18%)
    THP collapse           241.20 (  +0.00%)         248.50 (  +3.01%)
    THP splits             157.30 (  +0.00%)         161.40 (  +2.59%)

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Satoru Moriya <satoru.moriya@hds.com>
Cc: Simon Jeons <simon.jeons@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

CMA: make putback_lru_pages() call conditional

As per documentation and other places calling putback_lru_pages(),
putback_lru_pages() is called on error only.  Make the CMA code behave
consistently.

[akpm@linux-foundation.org: remove a test-n-branch in the wrapup code]
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/hugetlb.c: convert to pr_foo()

Cc: Michal Hocko <mhocko@suse.cz>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/memcontrol.c: convert printk(KERN_FOO) to pr_foo()

Acked-by: Sha Zhengju <handai.szj@taobao.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memcg, oom: provide more precise dump info while memcg oom happening

Currently when a memcg oom is happening the oom dump messages is still
global state and provides few useful info for users.  This patch prints
more pointed memcg page statistics for memcg-oom and take hierarchy into
consideration:

Based on Michal's advice, we take hierarchy into consideration: supppose
we trigger an OOM on A's limit

        root_memcg
            |
            A (use_hierachy=1)
           / \
          B   C
          |
          D
then the printed info will be:

  Memory cgroup stats for /A:...
  Memory cgroup stats for /A/B:...
  Memory cgroup stats for /A/C:...
  Memory cgroup stats for /A/B/D:...

Following are samples of oom output:

(1) Before change:

    mal-80 invoked oom-killer:gfp_mask=0xd0, order=0, oom_score_adj=0
    mal-80 cpuset=/ mems_allowed=0
    Pid: 2976, comm: mal-80 Not tainted 3.7.0+ #10
    Call Trace:
     [<ffffffff8167fbfb>] dump_header+0x83/0x1ca
     ..... (call trace)
     [<ffffffff8168a818>] page_fault+0x28/0x30
                             <<<<<<<<<<<<<<<<<<<<< memcg specific information
    Task in /A/B/D killed as a result of limit of /A
    memory: usage 101376kB, limit 101376kB, failcnt 57
    memory+swap: usage 101376kB, limit 101376kB, failcnt 0
    kmem: usage 0kB, limit 9007199254740991kB, failcnt 0
                             <<<<<<<<<<<<<<<<<<<<< print per cpu pageset stat
    Mem-Info:
    Node 0 DMA per-cpu:
    CPU    0: hi:    0, btch:   1 usd:   0
    ......
    CPU    3: hi:    0, btch:   1 usd:   0
    Node 0 DMA32 per-cpu:
    CPU    0: hi:  186, btch:  31 usd: 173
    ......
    CPU    3: hi:  186, btch:  31 usd: 130
                             <<<<<<<<<<<<<<<<<<<<< print global page state
    active_anon:92963 inactive_anon:40777 isolated_anon:0
     active_file:33027 inactive_file:51718 isolated_file:0
     unevictable:0 dirty:3 writeback:0 unstable:0
     free:729995 slab_reclaimable:6897 slab_unreclaimable:6263
     mapped:20278 shmem:35971 pagetables:5885 bounce:0
     free_cma:0
                             <<<<<<<<<<<<<<<<<<<<< print per zone page state
    Node 0 DMA free:15836kB ... all_unreclaimable? no
    lowmem_reserve[]: 0 3175 3899 3899
    Node 0 DMA32 free:2888564kB ... all_unrelaimable? no
    lowmem_reserve[]: 0 0 724 724
    lowmem_reserve[]: 0 0 0 0
    Node 0 DMA: 1*4kB (U) ... 3*4096kB (M) = 15836kB
    Node 0 DMA32: 41*4kB (UM) ... 702*4096kB (MR) = 2888316kB
    120710 total pagecache pages
    0 pages in swap cache
                             <<<<<<<<<<<<<<<<<<<<< print global swap cache stat
    Swap cache stats: add 0, delete 0, find 0/0
    Free swap  = 499708kB
    Total swap = 499708kB
    1040368 pages RAM
    58678 pages reserved
    169065 pages shared
    173632 pages non-shared
    [ pid ]   uid  tgid total_vm      rss nr_ptes swapents oom_score_adj name
    [ 2693]     0  2693     6005     1324      17        0             0 god
    [ 2754]     0  2754     6003     1320      16        0             0 god
    [ 2811]     0  2811     5992     1304      18        0             0 god
    [ 2874]     0  2874     6005     1323      18        0             0 god
    [ 2935]     0  2935     8720     7742      21        0             0 mal-30
    [ 2976]     0  2976    21520    17577      42        0             0 mal-80
    Memory cgroup out of memory: Kill process 2976 (mal-80) score 665 or sacrifice child
    Killed process 2976 (mal-80) total-vm:86080kB, anon-rss:69964kB, file-rss:344kB

We can see that messages dumped by show_free_areas() are longsome and can
provide so limited info for memcg that just happen oom.

(2) After change
    mal-80 invoked oom-killer: gfp_mask=0xd0, order=0, oom_score_adj=0
    mal-80 cpuset=/ mems_allowed=0
    Pid: 2704, comm: mal-80 Not tainted 3.7.0+ #10
    Call Trace:
     [<ffffffff8167fd0b>] dump_header+0x83/0x1d1
     .......(call trace)
     [<ffffffff8168a918>] page_fault+0x28/0x30
    Task in /A/B/D killed as a result of limit of /A
                             <<<<<<<<<<<<<<<<<<<<< memcg specific information
    memory: usage 102400kB, limit 102400kB, failcnt 140
    memory+swap: usage 102400kB, limit 102400kB, failcnt 0
    kmem: usage 0kB, limit 9007199254740991kB, failcnt 0
    Memory cgroup stats for /A: cache:32KB rss:30984KB mapped_file:0KB swap:0KB inactive_anon:6912KB active_anon:24072KB inactive_file:32KB active_file:0KB unevictable:0KB
    Memory cgroup stats for /A/B: cache:0KB rss:0KB mapped_file:0KB swap:0KB inactive_anon:0KB active_anon:0KB inactive_file:0KB active_file:0KB unevictable:0KB
    Memory cgroup stats for /A/C: cache:0KB rss:0KB mapped_file:0KB swap:0KB inactive_anon:0KB active_anon:0KB inactive_file:0KB active_file:0KB unevictable:0KB
    Memory cgroup stats for /A/B/D: cache:32KB rss:71352KB mapped_file:0KB swap:0KB inactive_anon:6656KB active_anon:64696KB inactive_file:16KB active_file:16KB unevictable:0KB
    [ pid ]   uid  tgid total_vm      rss nr_ptes swapents oom_score_adj name
    [ 2260]     0  2260     6006     1325      18        0             0 god
    [ 2383]     0  2383     6003     1319      17        0             0 god
    [ 2503]     0  2503     6004     1321      18        0             0 god
    [ 2622]     0  2622     6004     1321      16        0             0 god
    [ 2695]     0  2695     8720     7741      22        0             0 mal-30
    [ 2704]     0  2704    21520    17839      43        0             0 mal-80
    Memory cgroup out of memory: Kill process 2704 (mal-80) score 669 or sacrifice child
    Killed process 2704 (mal-80) total-vm:86080kB, anon-rss:71016kB, file-rss:340kB

This version provides more pointed info for memcg in "Memory cgroup stats
for XXX" section.

Signed-off-by: Sha Zhengju <handai.szj@taobao.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/md/persistent-data/dm-transaction-manager.c: rename HASH_SIZE

Fix the warning:

  drivers/md/persistent-data/dm-transaction-manager.c:28:1: warning: "HASH_SIZE" redefined
  In file included from include/linux/elevator.h:5,
                   from include/linux/blkdev.h:216,
                   from drivers/md/persistent-data/dm-block-manager.h:11,
                   from drivers/md/persistent-data/dm-transaction-manager.h:10,
                   from drivers/md/persistent-data/dm-transaction-manager.c:6:
  include/linux/hashtable.h:22:1: warning: this is the location of the previous definition

Cc: Alasdair Kergon <agk@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'x86-mm-for-linus' of git://git./linux/kernel/git/tip/tip

Pull x86 mm changes from Peter Anvin:
 "This is a huge set of several partly interrelated (and concurrently
  developed) changes, which is why the branch history is messier than
  one would like.

  The *really* big items are two humonguous patchsets mostly developed
  by Yinghai Lu at my request, which completely revamps the way we
  create initial page tables.  In particular, rather than estimating how
  much memory we will need for page tables and then build them into that
  memory -- a calculation that has shown to be incredibly fragile -- we
  now build them (on 64 bits) with the aid of a "pseudo-linear mode" --
  a #PF handler which creates temporary page tables on demand.

  This has several advantages:

  1. It makes it much easier to support things that need access to data
     very early (a followon patchset uses this to load microcode way
     early in the kernel startup).

  2. It allows the kernel and all the kernel data objects to be invoked
     from above the 4 GB limit.  This allows kdump to work on very large
     systems.

  3. It greatly reduces the difference between Xen and native (Xen's
     equivalent of the #PF handler are the temporary page tables created
     by the domain builder), eliminating a bunch of fragile hooks.

  The patch series also gets us a bit closer to W^X.

  Additional work in this pull is the 64-bit get_user() work which you
  were also involved with, and a bunch of cleanups/speedups to
  __phys_addr()/__pa()."

* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (105 commits)
  x86, mm: Move reserving low memory later in initialization
  x86, doc: Clarify the use of asm("%edx") in uaccess.h
  x86, mm: Redesign get_user with a __builtin_choose_expr hack
  x86: Be consistent with data size in getuser.S
  x86, mm: Use a bitfield to mask nuisance get_user() warnings
  x86/kvm: Fix compile warning in kvm_register_steal_time()
  x86-32: Add support for 64bit get_user()
  x86-32, mm: Remove reference to alloc_remap()
  x86-32, mm: Remove reference to resume_map_numa_kva()
  x86-32, mm: Rip out x86_32 NUMA remapping code
  x86/numa: Use __pa_nodebug() instead
  x86: Don't panic if can not alloc buffer for swiotlb
  mm: Add alloc_bootmem_low_pages_nopanic()
  x86, 64bit, mm: hibernate use generic mapping_init
  x86, 64bit, mm: Mark data/bss/brk to nx
  x86: Merge early kernel reserve for 32bit and 64bit
  x86: Add Crash kernel low reservation
  x86, kdump: Remove crashkernel range find limit for 64bit
  memblock: Add memblock_mem_size()
  x86, boot: Not need to check setup_header version for setup_data
  ...

Merge branch 'x86-cpu-for-linus' of git://git./linux/kernel/git/tip/tip

Pull x86 cpu updates from Peter Anvin:
 "This is a corrected attempt at the x86/cpu branch, this time with the
  fixes in that makes it not break on KVM (current or past), or any
  other virtualizer which traps on this configuration.

  Again, the biggest change here is enabling the WC+ memory type on AMD
  processors, if the BIOS doesn't."

* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, kvm: Add MSR_AMD64_BU_CFG2 to the list of ignored MSRs
  x86, cpu, amd: Fix WC+ workaround for older virtual hosts
  x86, AMD: Enable WC+ memory type on family 10 processors
  x86, AMD: Clean up init_amd()
  x86/process: Change %8s to %s for pr_warn() in release_thread()
  x86/cpu/hotplug: Remove CONFIG_EXPERIMENTAL dependency

Merge tag 'please-pull-misc-3.9' of git://git./linux/kernel/git/aegl/linux

Pull misc ia64 bits from Tony Luck.

* tag 'please-pull-misc-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
  MAINTAINERS: update SGI & ia64 Altix stuff
  sysctl: Enable IA64 "ignore-unaligned-usertrap" to be used cross-arch

Merge branch 'for-linus' of git://git./linux/kernel/git/s390/linux

Pull s390 update from Martin Schwidefsky:
 "The most prominent change in this patch set is the software dirty bit
  patch for s390.  It removes __HAVE_ARCH_PAGE_TEST_AND_CLEAR_DIRTY and
  the page_test_and_clear_dirty primitive which makes the common memory
  management code a bit less obscure.

  Heiko fixed most of the PCI related fallout, more often than not
  missing GENERIC_HARDIRQS dependencies.  Notable is one of the 3270
  patches which adds an export to tty_io to be able to resize a tty.

  The rest is the usual bunch of cleanups and bug fixes."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (42 commits)
  s390/module: Add missing R_390_NONE relocation type
  drivers/gpio: add missing GENERIC_HARDIRQ dependency
  drivers/input: add couple of missing GENERIC_HARDIRQS dependencies
  s390/cleanup: rename SPP to LPP
  s390/mm: implement software dirty bits
  s390/mm: Fix crst upgrade of mmap with MAP_FIXED
  s390/linker skript: discard exit.data at runtime
  drivers/media: add missing GENERIC_HARDIRQS dependency
  s390/bpf,jit: add vlan tag support
  drivers/net,AT91RM9200: add missing GENERIC_HARDIRQS dependency
  iucv: fix kernel panic at reboot
  s390/Kconfig: sort list of arch selected config options
  phylib: remove !S390 dependeny from Kconfig
  uio: remove !S390 dependency from Kconfig
  dasd: fix sysfs cleanup in dasd_generic_remove
  s390/pci: fix hotplug module init
  s390/pci: cleanup clp page allocation
  s390/pci: cleanup clp inline assembly
  s390/perf: cpum_cf: fallback to software sampling events
  s390/mm: provide PAGE_SHARED define
  ...

Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid

Pull HID subsystem updates from Jiri Kosina:
 "HID subsystem and drivers update. Highlights:

   - new support of a group of Win7/Win8 multitouch devices, from
     Benjamin Tissoires

   - fix for compat interface brokenness in uhid, from Dmitry Torokhov

   - conversion of drivers to use hid_driver helper, by H Hartley
     Sweeten

   - HID over I2C transport received ACPI enumeration support, written
     by Mika Westerberg

   - there is an ongoing effort to make HID sensor hubs independent of
     USB transport.  The first self-contained part of this work is
     provided here, done by Mika Westerberg

   - a few smaller fixes here and there, support for a couple new
     devices added"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (43 commits)
  HID: Correct Logitech order in hid-ids.h
  HID: LG4FF: Remove unnecessary deadzone code
  HID: LG: Prevent the Logitech Gaming Wheels deadzone
  HID: LG: Fix detection of Logitech Speed Force Wireless (WiiWheel)
  HID: LG: Add support for Logitech Momo Force (Red) Wheel
  HID: hidraw: print message when succesfully initialized
  HID: logitech: split accel, brake for Driving Force wheel
  HID: logitech: add report descriptor for Driving Force wheel
  HID: add ThingM blink(1) USB RGB LED support
  HID: uhid: make creating devices work on 64/32 systems
  HID: wiimote: fix nunchuck button parser
  HID: blacklist Velleman data acquisition boards
  HID: sensor-hub: don't limit the driver only to USB bus
  HID: sensor-hub: get rid of unused sensor_hub_grabbed_usages[] table
  HID: extend autodetect to handle I2C sensors as well
  HID: ntrig: use input_configured() callback to set the name
  HID: multitouch: do not use pointers towards hid-core
  HID: add missing GENERIC_HARDIRQ dependency
  HID: multitouch: make MT_CLS_ALWAYS_TRUE the new default class
  HID: multitouch: fix protocol for Elo panels
  ...

Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/trivial

Pull trivial tree from Jiri Kosina:
 "Assorted tiny fixes queued in trivial tree"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (22 commits)
  DocBook: update EXPORT_SYMBOL entry to point at export.h
  Documentation: update top level 00-INDEX file with new additions
  ARM: at91/ide: remove unsused at91-ide Kconfig entry
  percpu_counter.h: comment code for better readability
  x86, efi: fix comment typo in head_32.S
  IB: cxgb3: delay freeing mem untill entirely done with it
  net: mvneta: remove unneeded version.h include
  time: x86: report_lost_ticks doesn't exist any more
  pcmcia: avoid static analysis complaint about use-after-free
  fs/jfs: Fix typo in comment : 'how may' -> 'how many'
  of: add missing documentation for of_platform_populate()
  btrfs: remove unnecessary cur_trans set before goto loop in join_transaction
  sound: soc: Fix typo in sound/codecs
  treewide: Fix typo in various drivers
  btrfs: fix comment typos
  Update ibmvscsi module name in Kconfig.
  powerpc: fix typo (utilties -> utilities)
  of: fix spelling mistake in comment
  h8300: Fix home page URL in h8300/README
  xtensa: Fix home page URL in Kconfig
  ...

Merge branch 'akpm' (incoming from Andrew)

Merge misc patches from Andrew Morton:

 - Florian has vanished so I appear to have become fbdev maintainer
   again :(

 - Joel and Mark are distracted to welcome to the new OCFS2 maintainer

 - The backlight queue

 - Small core kernel changes

 - lib/ updates

 - The rtc queue

 - Various random bits

* akpm: (164 commits)
  rtc: rtc-davinci: use devm_*() functions
  rtc: rtc-max8997: use devm_request_threaded_irq()
  rtc: rtc-max8907: use devm_request_threaded_irq()
  rtc: rtc-da9052: use devm_request_threaded_irq()
  rtc: rtc-wm831x: use devm_request_threaded_irq()
  rtc: rtc-tps80031: use devm_request_threaded_irq()
  rtc: rtc-lp8788: use devm_request_threaded_irq()
  rtc: rtc-coh901331: use devm_clk_get()
  rtc: rtc-vt8500: use devm_*() functions
  rtc: rtc-tps6586x: use devm_request_threaded_irq()
  rtc: rtc-imxdi: use devm_clk_get()
  rtc: rtc-cmos: use dev_warn()/dev_dbg() instead of printk()/pr_debug()
  rtc: rtc-pcf8583: use dev_warn() instead of printk()
  rtc: rtc-sun4v: use pr_warn() instead of printk()
  rtc: rtc-vr41xx: use dev_info() instead of printk()
  rtc: rtc-rs5c313: use pr_err() instead of printk()
  rtc: rtc-at91rm9200: use dev_dbg()/dev_err() instead of printk()/pr_debug()
  rtc: rtc-rs5c372: use dev_dbg()/dev_warn() instead of printk()/pr_debug()
  rtc: rtc-ds2404: use dev_err() instead of printk()
  rtc: rtc-efi: use dev_err()/dev_warn()/pr_err() instead of printk()
  ...

rtc: rtc-davinci: use devm_*() functions

Use devm_*() functions to make cleanup paths more simple.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: rtc-max8997: use devm_request_threaded_irq()

Use devm_request_threaded_irq() to make cleanup paths more simple.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: rtc-max8907: use devm_request_threaded_irq()

Use devm_request_threaded_irq() to make cleanup paths more simple.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: rtc-da9052: use devm_request_threaded_irq()

Use devm_request_threaded_irq() to make cleanup paths more simple.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: rtc-wm831x: use devm_request_threaded_irq()

Use devm_request_threaded_irq() to make cleanup paths more simple.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: rtc-tps80031: use devm_request_threaded_irq()

Use devm_request_threaded_irq() to make cleanup paths more simple.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: rtc-lp8788: use devm_request_threaded_irq()

Use devm_request_threaded_irq() to make cleanup paths more simple.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: rtc-coh901331: use devm_clk_get()

Use devm_clk_get() to make cleanup paths more simple.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: rtc-vt8500: use devm_*() functions

Use devm_*() functions to make cleanup paths more simple.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: rtc-tps6586x: use devm_request_threaded_irq()

Use devm_request_threaded_irq() to make cleanup paths more simple.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: rtc-imxdi: use devm_clk_get()

Use devm_clk_get() to make cleanup paths more simple.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: rtc-cmos: use dev_warn()/dev_dbg() instead of printk()/pr_debug()

Fix the checkpatch warning as below:

  WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(...  to printk(KERN_ERR ...

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: rtc-pcf8583: use dev_warn() instead of printk()

Fix the checkpatch warning as below:

  WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(...  to printk(KERN_ERR ...

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: rtc-sun4v: use pr_warn() instead of printk()

Fix the checkpatch warning as below:

  WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(...  to printk(KERN_ERR ...

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: rtc-vr41xx: use dev_info() instead of printk()

Fix the checkpatch warning as below:

  WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(...  to printk(KERN_ERR ...

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: rtc-rs5c313: use pr_err() instead of printk()

Fix the checkpatch warning as below:

  WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(...  to printk(KERN_ERR ...

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: rtc-at91rm9200: use dev_dbg()/dev_err() instead of printk()/pr_debug()

Fix the checkpatch warning as below:

  WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(...  to printk(KERN_ERR ...

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: rtc-rs5c372: use dev_dbg()/dev_warn() instead of printk()/pr_debug()

Fix the checkpatch warning as below:

  WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(...  to printk(KERN_ERR ...

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: rtc-ds2404: use dev_err() instead of printk()

Fix the checkpatch warning as below:

  WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(...  to printk(KERN_ERR ...

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: rtc-efi: use dev_err()/dev_warn()/pr_err() instead of printk()

Fix the checkpatch warnings as below:

  WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(...  to printk(KERN_ERR ...
  WARNING: please, no space before tabs

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: max77686: use dev_info() instead of printk()

Fix the checkpatch warning as below:

  WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(...  to printk(KERN_ERR ...

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: use dev_warn()/dev_dbg()/pr_err() instead of printk()

Fix the checkpatch warning as below:

  WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(...  to printk(KERN_ERR ...

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-sa1100.c: move clock enable/disable to probe/remove

The original sa1100_rtc_open/sa1100_rtc_release will be called when the
/dev/rtc0 is opened or closed.  In fact, these two functions will
enable/disable the clock.  Disabling clock will make rtc not work.  So
only enable/disable clock when probe/remove the device.

Signed-off-by: Chao Xie <chao.xie@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Leo Song <liangs@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: max8997: add driver for max8997 rtc

Add an rtc driver for Maxim 8997 multifunction chip.  Max8997 has rtc
module in it.  and it can be used for timekeeping clock and system alarm.
It provide various operational mode those are BCD/binary, 24/12hour,
am/pm.  Driver sets binary/24/ for default.  Maxim 8997 also supports
SMPL(Sudden Momentary Power Loss), WTSR (Watchdog Timeout and Software
Reset).

Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Cc: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-s3c.c: use dev_dbg() instaed of pr_debug()

Use dev_dbg() instaed of pr_debug() to be consistent.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

arm: mvebu: add RTC support for Armada 370 and Armada XP

The Armada 370 and Armada XP Socs have the same controller that the one
used in the orion platforms.  This patch updates the device tree for
these SoCs.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-pl031.c: add wakeup support

Mark the pl031 as wake-up capable so that rtcwake and suspend test can work.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: add support for spi rtc rx4581

[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Torben Hohn <torbenh@linutronix.de>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-tps65910.c: set irq flag to IRQF_EARLY_RESUME during irq request

All interrupt get disabled during system suspend and enabled during system
resume.  The enabling/disabling of interrupt happen in sequence of
interrupt registration with framework.

Therefore, in resume, the parent interrupt of this device enabled before
the RTC irq interrupt enabled.  If RTC is enabled for alarm wake and if
system wake by alarm then there is interrupt pending for RTC.  In resume,
the parent interrupt get enabled before the rtc interrupt and hence ISR
get served.  In ISR, it founds that rtc interrupt is disabled and so it
does not call the rtc isr handler and hence it misses the interrupt.

Setting flag for early resume so that rtc interrupt get enabled before
parent interrupt and so rtc interrupt get enabled when parent interrupt
handler check for interrupt of device and call the rtc handler if it is
there.  This way it will not miss the interrupt.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-tps65910.c: use sleep_pm_ops macro for initialising suspend/resume callbacks

Use SET_SYSTEM_SLEEP_PM_OPS for setting suspend/resume callbacks for
dev_pm_ops.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-tps65910.c: remove unnecessary irq stat save and restore

The driver stores the interrupt enable register before going to suspend
and restore in resume.  Also it enables alarm before going to suspend.

The driver only write the Interrupt enable register for enabling ALARM and
does not enable any other bits.  So it is not require to save complete
register and enable ALARM interrupt before suspend and restore in resume.

Also ALARM interrupt already enable if alarm is enabled before going to
suspend and hence it is not require to enable explictly in suspend.

Removing such above code.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-tps65910.c: enable/disable wake in suspend/resume

Making the rtc driver as wakeup capabale and leaving the wake
enable/disable decision to user space through a sysfs attribute.

In suspend, enable wake if device wakeup enabled.  In resume disable wake
again.

This change is inline with the Documentation/power/devices.txt#
/sys/devices/.../power/wakeup files

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: add RTC driver for TPS80031/TPS80032

Add an RTC driver for TPS80031/TPS80032 chips by TI.  This driver
supports:
 - Setting and getting time and date.
 - Setting and reading alarm time.
 - Alarm and interrupt functionlity.

[akpm@linux-foundation.org: remove obsolete __devinit/__devexit]
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: add new lp8788 rtc driver

TI LP8788 PMU supports regulators, battery charger, RTC, ADC, backlight
driver and current sinks.  This patch enables LP8788 rtc module.

Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: "devendra.aaru" <devendra.aaru@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-ds2404.c: use module_platform_driver macro

Remove removes some code duplication by using module_platform_driver().

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc: remove unnecessary semicolons

Found by Coccinelle: http://coccinelle.lip6.fr/

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-pxa.c: avoid cpuid checking

pxa-rtc is widely used in pxa27x/pxa3xx/pxa93x/pxa95x. Checking cpuid in
pxa-rtc driver is unnecessary since we assign on-chip device in soc files.

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc: use of_match_ptr() macro

This eliminates having an #ifdef returning NULL for the case when OF is
disabled.  Maintains consistency in cases where OF is always selected.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc-pcf8523: add low battery voltage support

Implement reading of the battery voltage low signal for rtc-pcf8523.

The bit is read-only and cannot be cleared by software, so no
clear function is implemented.

[akpm@linux-foundation.org: omit pcf8563_rtc_ioctl() if CONFIG_RTC_INTF_DEV=n]
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: max77686: add Maxim 77686 driver

Add a driver to support max77686 rtc.  MAX77686 rtc support smpl and wtsr
mode.  It has two alarm register which can be used for alarming to wake
system up.  This drvier uses regmap to access its register.

[akpm@linux-foundation.org: remove inline, __devinit annotations]
[jg1.han@samsung.com: fix build warnings]
[akpm@linux-foundation.org: simplify code]
Signed-off-by: Chiwoong Byun <woong.byun@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myugnjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-pxa.c: fix alarm can't wake up system issue

Fix alarm can't wake up system issue

Signed-off-by: Leo Song <liangs@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-pxa.c: fix alarm not match issue

Fix pxa rtc alarm issue by setting week of month and day of week in
rdar/rdcr or it would not match.

Signed-off-by: Leo Song <liangs@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc: dump small buffers via %*ph

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/nsproxy.c: remove duplicate task_cred_xxx for user_ns

We can use user_ns, which is also assigned from task_cred_xxx(tsk,
user_ns), at the beginning of copy_namespaces().

Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

binfmt_elf: remove unused argument in fill_elf_header

In fill_elf_header(), elf->e_ident[EI_OSABI] is always set to ELF_OSABI,
so remove the unused argument 'osabi'.

Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: fix USLEEP_RANGE test

Do not test udelay() for a value less than 10usec when passed a variable
instead of a hard-coded number; there is no way for checkpatch to know the
value of the variable.  As it is today, it will complain about variables
with alphanumeric characters plus '_', e.g.  foo_bar, but not variables
with other characters, eg.  foo->bar.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: Add check for kcalloc argument order

kcalloc is sometimes misused with the first and second arguments switched.

Same issue with kmalloc_array too.

Bleat if sizeof is the first argument

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: don't emit the CamelCase warning for PageFoo

I'm getting a ton of these:

  WARNING: Avoid CamelCase: <PageTransHuge>
  #140: FILE: mm/migrate.c:1576:
  +       if (PageTransHuge(page) && page_count(page) != 3) {

So exclude anything which starts with "Page".

Tested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: add Joe to MAINTAINERS

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: warn on unnecessary __dev<foo> section markings

Get people to stop adding __devinit and __devexit section markings.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Andy Whitcroft <apw@canonical.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: prefer dev_<level>( to dev_printk(KERN_<LEVEL>

Add YA check to printk style.

dev_<level> uses are functions and generate smaller
object code than dev_printk(KERN_<LEVEL>.

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

decompressors: make the default XZ_DEC_* config match the selected architecture

Change the defautl XZ_DEC_* config symbol to match the configured
architecture.  It is perfectly legitimate to support multiple XZ BCJ
filters for different architectures (e.g.: to mount foreign squashfs/xz
compressed filesystems), it is however more natural not to select them all
by default, but only the one matching the configured architecture.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Lasse Collin <lasse.collin@tukaani.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

decompressors: drop dependency on CONFIG_EXPERT

Remove the XZ_DEC_* depedencey on CONFIG_EXPERT as recommended by Lasse
Colin.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Lasse Collin <lasse.collin@tukaani.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

decompressors: group XZ_DEC_* symbols under an if XZ_BCJ / endif

Group all architecture-specific BCJ filter configuration symbols under an
if XZ_BCJ / endif statement.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Lasse Collin <lasse.collin@tukaani.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lib/parser.c: fix up comments for valid return values from match_number

match_number() has return values of -ENOMEM, -EINVAL and -ERANGE.  So, for
all the functions calling match_number, the return value should include
these values.  Fix up the comments to reflect the correct values.

Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: lp855x_bl: simplify bl_get_brightness()

Getting the brightness value is not critical, no need to read the actual
register value.  To simplify it, just return the 'bl->props.brightness'
value.  Then, lp855x_read_byte() can be removed, not used any more.

Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: lp855x_bl: support new LP8557 device

LP8557 is one of LP855x family device, but it has different register map
and initialization process.  To support this device, device specific
configuration is done through the lp855x_device_config structure.

Few register definitions are fixed for better readability.
  BRIGHTNESS_CTRL -> LP855X_BRIGHTNESS_CTRL
  DEVICE_CTRL     -> LP855X_DEVICE_CTRL
  EEPROM_START    -> LP855X_EEPROM_START
  EEPROM_END      -> LP855X_EEPROM_END
  EPROM_START     -> LP8556_EPROM_START
  EPROM_END       -> LP8556_EPROM_END

And LP8557 register definitions are added.  New register function,
lp855x_update_bit() is added.

Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: lp855x_bl: introduce device configuration flow

At this moment, LP855x device driver has fixed register configuration.
For example, fixed register addresses and values are set on the device
initialization.  But new device of LP855x family, LP8557 has different
register map and initialization sequence.  To support new device
architecture, initialization process should be changed.

 Introduce new structure: lp855x_device_config
 =============================================
 With lp855x_device_config, device specific features are configurable.
 Use configurable function calls and register addresses rather than fixed values.

 Change on device initialization
 ===============================
 In old LP855x driver architecture, the device initialization was simple.
 - Just update the brightness/device control register/ROM area(optional).
 In new LP855x driver architecture, two more works are added - pre_init and
 post_init.
 Those init functions are optional, used for new device LP8557.

 New device initialization flow: generic sequence
 =================================================
 1) pre_init_device()
 2) update the brightness register
 3) update the device control register
 4) update ROM area if need
 5) post_init_device()

 Name change
 ===========
 Use generic name 'lp855x_configure()' instead of 'lp855x_init_registers()'.

Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/video/backlight/adp88?0_bl.c: fix resume

Clearing the NSTBY bit in the control register also automatically clears
the BLEN bit.  So we need to make sure to set it again during resume,
otherwise the backlight will stay off.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/video/backlight/lm3630_bl.c: remove ret = -EIO of lm3630_backlight_register()

There is no need to return -EIO, because backlight_device_register()
already returns correct error values.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Daniel Jeong <daniel.jeong@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/video/backlight/s6e63m0.c: report ->gamma_table_count correctly

gamma_table has 3 arrays which each hold MAX_GAMMA_LEVEL pointers to int.

The current code sets ->gamma_table_count to 6 on 64bit arches and to 3 on
32 bit arches.  It should be 3 on everything.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/video/backlight/88pm860x_bl.c: add missing of_node_put()

of_find_node_by_name() returns a node pointer with refcount incremented,
use of_node_put() on it when done.

of_find_node_by_name() will call of_node_put() against the node pass to
from parameter, thus we also need to call of_node_get(from) before calling
of_find_node_by_name().

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: add an AS3711 PMIC backlight driver

This is an initial commit of a backlight driver, using step-up DCDC
power supplies on AS3711 PMIC.  Only one mode has actually been tested,
several further modes have been implemented "dry," but disabled to avoid
accidental hardware damage.  Anyone wishing to use any of those modes
will have to modify the driver.

Tested on sh73a0-based kzm9g board.  Only one mode has been tested and
is enabled.  That mode copies the sample code from the manufacturer.
Deviations from that code proved to be fatal for the hardware...

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/video/backlight/Makefile: cleanup

Fix up indenting.  Also alphasort all entries, which reduces patch
collisions.

Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fb: backlight: add the Himax HX-8357B LCD controller

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Brian Lilly <brian@crystalfontz.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/video/backlight/ld9040.c: use devm_regulator_bulk_get() API

devm_regulator_bulk_get is device managed and saves some cleanup
and exit code.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/video/backlight/l4f00242t03.c: convert to devm_regulator_get()

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/video/backlight/lm3639_bl.c: remove ret = -EIO at error paths of probe

The APIs are returning correctly the err codes, no need to assign -EIO
to the ret again.

Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Acked-by: Daniel Jeong <daniel.jeong@ti.com>
Cc: G.Shark Jeong <gshark.jeong@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: corgi_lcd: use lcd_get_data instead of dev_get_drvdata

Use the wrapper function for getting the driver data using lcd_device
instead of using dev_get_drvdata with &ld->dev, so we can directly pass a
struct lcd_device.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: omap1: use bl_get_data instead of dev_get_drvdata

Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: tosa: use bl_get_data instead of dev_get_drvdata

Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: corgi_lcd: use bl_get_data instead of dev_get_drvdata

Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: ams369fg06: use bl_get_data instead of dev_get_drvdata

Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pwm_backlight: use bl_get_data instead of dev_get_drvdata

Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: aat2870: use bl_get_data instead of dev_get_drvdata

Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: lms501kf03: use spi_get_drvdata and spi_set_drvdata

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: corgi_lcd: use spi_get_drvdata and spi_set_drvdata

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: tosa: use spi_get_drvdata and spi_set_drvdata

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: vgg2432a4: use spi_get_drvdata and spi_set_drvdata

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: ams369fg06: use spi_get_drvdata and spi_set_drvdata

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: lms283gf05: use spi_get_drvdata and spi_set_drvdata

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: tdo24m: use spi_get_drvdata and spi_set_drvdata

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: ltv350qv: use spi_get_drvdata and spi_set_drvdata

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: s6e63m0: use spi_get_drvdata and spi_set_drvdata

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>