Qipeng Zha [Wed, 29 Jul 2015 10:23:32 +0000 (18:23 +0800)]
serial: 8250: Auto CTS control by HW if AFE enabled
According to DesignWare 8250 spec, if auto flow control
mode is enabled, a change in CTS does not cause an interrupt,
so sw-assisted CTS flow control mode will not work properly.
There reported an GPS firmware download failure issue, and we
verified the root cause is, the default sw-assisted CTS flow
control mode can not work properly since no interrupt when got
CTS signal.
This patch is to enable auto CTS mode by defaut if CRTSCTS
is enable for DesignWare 8250 controller.
Signed-off-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Uwe Kleine-König [Mon, 27 Jul 2015 16:09:33 +0000 (18:09 +0200)]
serial: mpc52xx: let tx_empty callback return either 0 or TIOCSER_TEMT
Documenation/serial/driver requests that the tx_empty callback should
return 0 if there are still chars in the fifo or shifter or TIOCSER_TEMT
(0x01) if no character is pending to be sent.
Fix the mpc52xx serial driver to not return MPC52xx_PSC_SR_TXEMP (i.e.
0x0800) but TIOCSER_TEMT as documented.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Niklas Cassel [Sat, 25 Jul 2015 00:02:46 +0000 (02:02 +0200)]
serial: etraxfs-uart: use mctrl_gpio helpers for handling modem signals
In order to use the mctrl_gpio helpers, we change the DT bindings:
ri-gpios renamed to rng-gpios. cd-gpios renamed to dcd-gpios.
However, no in-tree dts/dtsi specifies these, so no worries.
Signed-off-by: Niklas Cassel <nks@flawful.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Niklas Cassel [Sat, 25 Jul 2015 00:00:40 +0000 (02:00 +0200)]
serial: etraxfs-uart: remove empty functions
Implementing enable_ms is optional by serial_core.
check_modem_status is just an empty local function.
Signed-off-by: Niklas Cassel <nks@flawful.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shenwei Wang [Thu, 30 Jul 2015 15:32:36 +0000 (10:32 -0500)]
Serial: imx: add dev_pm_ops to support suspend to ram/disk
When system goes into low power states like SUSPEND_MEM and
HIBERNATION, the hardware IP block may be powered off to reduce
the power consumption. This power down may cause problems on
some imx platforms, because the hardware settings are reset to
its power on default values which may differ from the ones when
it power off. This patch added the dev_pm_ops and implemented
two callbacks: suspend_noirq and resume_noirq, which will save
the necessory hardware parameters right before power down and
recover them before system uses the hardware.
Because added the dev_pm_ops, the old suspend/resume callbacks
under platform_driver will not be called any more. Changed their
prototypes and moved those two callbacks into dev_pm_ops too.
Signed-off-by: Shenwei Wang <shenwei.wang@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Masahiro Yamada [Fri, 24 Jul 2015 06:58:28 +0000 (15:58 +0900)]
serial: 8250_uniphier: call clk_disable_unprepare() on failure path
If serial8250_register_8250_port() fails, disable and unprepare the
clock before exiting.
Fixes:
1a8d2903cb6a ("serial: 8250_uniphier: add UniPhier serial driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hung [Tue, 28 Jul 2015 03:59:24 +0000 (11:59 +0800)]
serial: 8250_pci: add RS485 for F81504/508/512
Add RS485 control for Fintek F81504/508/512
F81504/508/512 can control their RTS with H/W mode.
PCI configuration space for each port is 0x40 + idx * 8 + 7.
When it set with 0x01, it's configured with RS232 mode.
RTS is controlled by MCR.
When it set with 0x11, it's configured with RS485 mode.
RTS is controlled by H/W, RTS low with idle & RX, high with TX.
When it set with 0x31, it's configured with RS485 mode.
RTS is controlled by H/W, RTS high with idle & RX, low with TX.
We will force 0x01 on pci_fintek_setup().
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Richard Watts [Tue, 19 May 2015 15:06:53 +0000 (16:06 +0100)]
Avoid usb reset crashes by making tty_io cdevs truly dynamic
Avoid usb reset crashes by making tty_io cdevs truly dynamic
Signed-off-by: Richard Watts <rrw@kynesim.co.uk>
Reported-by: Duncan Mackintosh <DMackintosh@cbnl.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fabio Estevam [Mon, 27 Jul 2015 18:15:59 +0000 (15:15 -0300)]
Revert "tty: serial: imx.c: Reset UART before activating interrupts"
This reverts commit
e95044ba4fee93f5ea8a1a24b2d921e148503833.
Commit
e95044ba4fee93 ("tty: serial: imx.c: Reset UART before activating
interrupts") terribly messes up with the console on mx6 boards, so
let's revert it.
Reported-by: kernelci.org bot <bot@kernelci.org>
Cc: David Jander <david@protonic.nl>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Mon, 27 Jul 2015 18:12:39 +0000 (11:12 -0700)]
Merge 4.2-rc4 into tty-next
Other serial driver work wants to build on patches now in 4.2-rc4 so
merge the branch so this can properly happen.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sun, 26 Jul 2015 19:26:21 +0000 (12:26 -0700)]
Linux 4.2-rc4
Linus Torvalds [Sun, 26 Jul 2015 18:46:32 +0000 (11:46 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fix from Thomas Gleixner:
"A single fix for the intel cqm perf facility to prevent IPIs from
interrupt context"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/cqm: Return cached counter value from IRQ context
Linus Torvalds [Sun, 26 Jul 2015 18:14:04 +0000 (11:14 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"This update contains:
- the manual revert of the SYSCALL32 changes which caused a
regression
- a fix for the MPX vma handling
- three fixes for the ioremap 'is ram' checks.
- PAT warning fixes
- a trivial fix for the size calculation of TLB tracepoints
- handle old EFI structures gracefully
This also contains a PAT fix from Jan plus a revert thereof. Toshi
explained why the code is correct"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/pat: Revert 'Adjust default caching mode translation tables'
x86/asm/entry/32: Revert 'Do not use R9 in SYSCALL32' commit
x86/mm: Fix newly introduced printk format warnings
mm: Fix bugs in region_is_ram()
x86/mm: Remove region_is_ram() call from ioremap
x86/mm: Move warning from __ioremap_check_ram() to the call site
x86/mm/pat, drivers/media/ivtv: Move the PAT warning and replace WARN() with pr_warn()
x86/mm/pat, drivers/infiniband/ipath: Replace WARN() with pr_warn()
x86/mm/pat: Adjust default caching mode translation tables
x86/fpu: Disable dependent CPU features on "noxsave"
x86/mpx: Do not set ->vm_ops on MPX VMAs
x86/mm: Add parenthesis for TLB tracepoint size calculation
efi: Handle memory error structures produced based on old versions of standard
Thomas Gleixner [Sun, 26 Jul 2015 08:27:37 +0000 (10:27 +0200)]
x86/mm/pat: Revert 'Adjust default caching mode translation tables'
Toshi explains:
"No, the default values need to be set to the fallback types,
i.e. minimal supported mode. For WC and WT, UC is the fallback type.
When PAT is disabled, pat_init() does update the tables below to
enable WT per the default BIOS setup. However, when PAT is enabled,
but CPU has PAT -errata, WT falls back to UC per the default values."
Revert:
ca1fec58bc6a 'x86/mm/pat: Adjust default caching mode translation tables'
Requested-by: Toshi Kani <toshi.kani@hp.com>
Cc: Jan Beulich <jbeulich@suse.de>
Link: http://lkml.kernel.org/r/1437577776.3214.252.camel@hp.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Matt Fleming [Tue, 21 Jul 2015 14:55:09 +0000 (15:55 +0100)]
perf/x86/intel/cqm: Return cached counter value from IRQ context
Peter reported the following potential crash which I was able to
reproduce with his test program,
[ 148.765788] ------------[ cut here ]------------
[ 148.765796] WARNING: CPU: 34 PID: 2840 at kernel/smp.c:417 smp_call_function_many+0xb6/0x260()
[ 148.765797] Modules linked in:
[ 148.765800] CPU: 34 PID: 2840 Comm: perf Not tainted 4.2.0-rc1+ #4
[ 148.765803]
ffffffff81cdc398 ffff88085f105950 ffffffff818bdfd5 0000000000000007
[ 148.765805]
0000000000000000 ffff88085f105990 ffffffff810e413a 0000000000000000
[ 148.765807]
ffffffff82301080 0000000000000022 ffffffff8107f640 ffffffff8107f640
[ 148.765809] Call Trace:
[ 148.765810] <NMI> [<
ffffffff818bdfd5>] dump_stack+0x45/0x57
[ 148.765818] [<
ffffffff810e413a>] warn_slowpath_common+0x8a/0xc0
[ 148.765822] [<
ffffffff8107f640>] ? intel_cqm_stable+0x60/0x60
[ 148.765824] [<
ffffffff8107f640>] ? intel_cqm_stable+0x60/0x60
[ 148.765825] [<
ffffffff810e422a>] warn_slowpath_null+0x1a/0x20
[ 148.765827] [<
ffffffff811613f6>] smp_call_function_many+0xb6/0x260
[ 148.765829] [<
ffffffff8107f640>] ? intel_cqm_stable+0x60/0x60
[ 148.765831] [<
ffffffff81161748>] on_each_cpu_mask+0x28/0x60
[ 148.765832] [<
ffffffff8107f6ef>] intel_cqm_event_count+0x7f/0xe0
[ 148.765836] [<
ffffffff811cdd35>] perf_output_read+0x2a5/0x400
[ 148.765839] [<
ffffffff811d2e5a>] perf_output_sample+0x31a/0x590
[ 148.765840] [<
ffffffff811d333d>] ? perf_prepare_sample+0x26d/0x380
[ 148.765841] [<
ffffffff811d3497>] perf_event_output+0x47/0x60
[ 148.765843] [<
ffffffff811d36c5>] __perf_event_overflow+0x215/0x240
[ 148.765844] [<
ffffffff811d4124>] perf_event_overflow+0x14/0x20
[ 148.765847] [<
ffffffff8107e7f4>] intel_pmu_handle_irq+0x1d4/0x440
[ 148.765849] [<
ffffffff811d07a6>] ? __perf_event_task_sched_in+0x36/0xa0
[ 148.765853] [<
ffffffff81219bad>] ? vunmap_page_range+0x19d/0x2f0
[ 148.765854] [<
ffffffff81219d11>] ? unmap_kernel_range_noflush+0x11/0x20
[ 148.765859] [<
ffffffff814ce6fe>] ? ghes_copy_tofrom_phys+0x11e/0x2a0
[ 148.765863] [<
ffffffff8109e5db>] ? native_apic_msr_write+0x2b/0x30
[ 148.765865] [<
ffffffff8109e44d>] ? x2apic_send_IPI_self+0x1d/0x20
[ 148.765869] [<
ffffffff81065135>] ? arch_irq_work_raise+0x35/0x40
[ 148.765872] [<
ffffffff811c8d86>] ? irq_work_queue+0x66/0x80
[ 148.765875] [<
ffffffff81075306>] perf_event_nmi_handler+0x26/0x40
[ 148.765877] [<
ffffffff81063ed9>] nmi_handle+0x79/0x100
[ 148.765879] [<
ffffffff81064422>] default_do_nmi+0x42/0x100
[ 148.765880] [<
ffffffff81064563>] do_nmi+0x83/0xb0
[ 148.765884] [<
ffffffff818c7c0f>] end_repeat_nmi+0x1e/0x2e
[ 148.765886] [<
ffffffff811d07a6>] ? __perf_event_task_sched_in+0x36/0xa0
[ 148.765888] [<
ffffffff811d07a6>] ? __perf_event_task_sched_in+0x36/0xa0
[ 148.765890] [<
ffffffff811d07a6>] ? __perf_event_task_sched_in+0x36/0xa0
[ 148.765891] <<EOE>> [<
ffffffff8110ab66>] finish_task_switch+0x156/0x210
[ 148.765898] [<
ffffffff818c1671>] __schedule+0x341/0x920
[ 148.765899] [<
ffffffff818c1c87>] schedule+0x37/0x80
[ 148.765903] [<
ffffffff810ae1af>] ? do_page_fault+0x2f/0x80
[ 148.765905] [<
ffffffff818c1f4a>] schedule_user+0x1a/0x50
[ 148.765907] [<
ffffffff818c666c>] retint_careful+0x14/0x32
[ 148.765908] ---[ end trace
e33ff2be78e14901 ]---
The CQM task events are not safe to be called from within interrupt
context because they require performing an IPI to read the counter value
on all sockets. And performing IPIs from within IRQ context is a
"no-no".
Make do with the last read counter value currently event in
event->count when we're invoked in this context.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vikas Shivappa <vikas.shivappa@intel.com>
Cc: Kanaka Juvva <kanaka.d.juvva@intel.com>
Cc: Will Auld <will.auld@intel.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/1437490509-15373-1-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Linus Torvalds [Sun, 26 Jul 2015 03:11:12 +0000 (20:11 -0700)]
Merge tag 'usb-4.2-rc4' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here's a few USB and PHY fixes for 4.2-rc4.
Nothing major, the shortlog has the full details.
All of these have been in linux-next successfully"
* tag 'usb-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (21 commits)
USB: OHCI: fix bad #define in ohci-tmio.c
cdc-acm: Destroy acm_minors IDR on module exit
usb-storage: Add ignore-device quirk for gm12u320 based usb mini projectors
usb-storage: ignore ZTE MF 823 card reader in mode 0x1225
USB: OHCI: Fix race between ED unlink and URB submission
usb: core: lpm: set lpm_capable for root hub device
xhci: do not report PLC when link is in internal resume state
xhci: prevent bus_suspend if SS port resuming in phase 1
xhci: report U3 when link is in resume state
xhci: Calculate old endpoints correctly on device reset
usb: xhci: Bugfix for NULL pointer deference in xhci_endpoint_init() function
xhci: Workaround to get D3 working in Intel xHCI
xhci: call BIOS workaround to enable runtime suspend on Intel Braswell
usb: dwc3: Reset the transfer resource index on SET_INTERFACE
usb: gadget: udc: core: Fix argument of dma_map_single for IOMMU
usb: gadget: mv_udc_core: fix phy_regs I/O memory leak
usb: ulpi: ulpi_init should be executed in subsys_initcall
phy: berlin-usb: fix divider for BG2
phy: berlin-usb: fix divider for BG2CD
phy/pxa: add HAS_IOMEM dependency
...
Linus Torvalds [Sun, 26 Jul 2015 03:05:07 +0000 (20:05 -0700)]
Merge tag 'tty-4.2-rc4' of git://git./linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a number of small serial and tty fixes for reported issues.
All have been in linux-next successfully"
* tag 'tty-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: vt: Fix !TASK_RUNNING diagnostic warning from paste_selection()
serial: core: Fix crashes while echoing when closing
m32r: Add ioreadXX/iowriteXX big-endian mmio accessors
Revert "serial: imx: initialized DMA w/o HW flow enabled"
sc16is7xx: fix FIFO address of secondary UART
sc16is7xx: fix Kconfig dependencies
serial: etraxfs-uart: Fix release etraxfs_uart_ports
tty/vt: Fix the memory leak in visual_init
serial: amba-pl011: Fix devm_ioremap_resource return value check
n_tty: signal and flush atomically
Linus Torvalds [Sun, 26 Jul 2015 03:03:10 +0000 (20:03 -0700)]
Merge tag 'staging-4.2-rc4' of git://git./linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are a number of iio and staging driver fixes for reported issues
for 4.2-rc4.
All have been in linux-next for a while with no problems"
* tag 'staging-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (34 commits)
iio:light:stk3310: make endianness independent of host
iio:light:stk3310: move device register to end of probe
iio: mma8452: use iio event type IIO_EV_TYPE_MAG
iio: mcp320x: Fix NULL pointer dereference
iio: adc: vf610: fix the adc register read fail issue
iio: mlx96014: Replace offset sign
iio: magnetometer: mmc35240: fix SET/RESET sequence
iio: magnetometer: mmc35240: Fix SET/RESET mask
iio: magnetometer: mmc35240: Fix crash in pm suspend
iio:magnetometer:bmc150_magn: output intended variable
iio:magnetometer:bmc150_magn: add regmap dependency
staging: vt6656: check ieee80211_bss_conf bssid not NULL
staging: vt6655: check ieee80211_bss_conf bssid not NULL
iio: tmp006: Check channel info on write
iio: sx9500: Add missing init in sx9500_buffer_pre{en,dis}able()
iio:light:ltr501: fix regmap dependency
iio:light:ltr501: fix variable in ltr501_init
iio: sx9500: fix bug in compensation code
iio: sx9500: rework error handling of raw readings
iio: magnetometer: mmc35240: fix available sampling frequencies
...
Linus Torvalds [Sun, 26 Jul 2015 02:50:59 +0000 (19:50 -0700)]
Merge tag 'char-misc-4.2-rc4' of git://git./linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some char and misc driver fixes for reported issues.
One parport patch is reverted as it was incorrect, thanks to testing
by the 0-day bot"
* tag 'char-misc-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
parport: Revert "parport: fix memory leak"
mei: prevent unloading mei hw modules while the device is opened.
misc: mic: scif bug fix for vmalloc_to_page crash
parport: fix freeing freed memory
parport: fix memory leak
parport: fix error handling
Sudip Mukherjee [Sat, 25 Jul 2015 07:49:40 +0000 (13:19 +0530)]
parport: Revert "parport: fix memory leak"
This reverts commit
23c405912b88 ("parport: fix memory leak")
par_dev->state was already being removed in parport_unregister_device().
Reported-by: Ying Huang <ying.huang@intel.com>
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sat, 25 Jul 2015 18:42:54 +0000 (11:42 -0700)]
Merge tag 'trace-v4.2-rc2-fix3' of git://git./linux/kernel/git/rostedt/linux-trace
Pull ftrace fix from Steven Rostedt:
"Back in 3.16 the ftrace code was redesigned and cleaned up to remove
the double iteration list (one for registered ftrace ops, and one for
registered "global" ops), to just use one list. That simplified the
code but also broke the function tracing filtering on pid.
This updates the code to handle the filtering again with the new
logic"
* tag 'trace-v4.2-rc2-fix3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Fix breakage of set_ftrace_pid
Linus Torvalds [Sat, 25 Jul 2015 18:36:12 +0000 (11:36 -0700)]
Merge branch 'libnvdimm-fixes' of git://git./linux/kernel/git/djbw/nvdimm
Pull libnvdimm fix from Dan Williams:
"A minor fix for the libnvdimm subsystem.
This is not critical. The problem can be worked around in userspace
by putting the namespace temporarily into raw mode
(ndctl_namespace_set_raw_mode() from libndctl), but that is awkward
for management utilities.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm:
libnvdimm: fix namespace seed creation
Linus Torvalds [Sat, 25 Jul 2015 18:24:58 +0000 (11:24 -0700)]
Merge tag 'md/4.2-fixes' of git://neil.brown.name/md
Pull md fixes from Neil Brown:
"Some md fixes for 4.2
Several are tagged for -stable.
A few aren't because they are not very, serious or because they are in
the 'experimental' cluster code"
* tag 'md/4.2-fixes' of git://neil.brown.name/md:
md/raid5: clear R5_NeedReplace when no longer needed.
Fix read-balancing during node failure
md-cluster: fix bitmap sub-offset in bitmap_read_sb
md: Return error if request_module fails and returns positive value
md: Skip cluster setup in case of error while reading bitmap
md/raid1: fix test for 'was read error from last working device'.
md: Skip cluster setup for dm-raid
md: flush ->event_work before stopping array.
md/raid10: always set reshape_safe when initializing reshape_position.
md/raid5: avoid races when changing cache size.
Linus Torvalds [Sat, 25 Jul 2015 18:19:38 +0000 (11:19 -0700)]
Merge tag 'for-linus-
20150724' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"Two trivial updates. I meant to send these much earlier, but I've
been preoccupied.
- Add MAINTAINERS entry for diskonchip g3 driver
- Fix an overlooked conflict in bitfield value assignments
The latter update is a bit overdue, but there's no reason to wait any
longer"
* tag 'for-linus-
20150724' of git://git.infradead.org/linux-mtd:
mtd: nand: Fix NAND_USE_BOUNCE_BUFFER flag conflict
MAINTAINERS: mtd: docg3: add docg3 maintainer
Dan Williams [Sat, 25 Jul 2015 03:42:34 +0000 (23:42 -0400)]
libnvdimm: fix namespace seed creation
A new BLK namespace "seed" device is created whenever the current seed
is successfully probed. However, if that namespace is assigned to a BTT
it may never directly experience a successful probe as it is a
subordinate device to a BTT configuration.
The effect of the current code is that no new namespaces can be
instantiated, after the seed namespace, to consume available BLK DPA
capacity. Fix this by treating a successful BTT probe event as a
successful probe event for the backing namespace.
Reported-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Linus Torvalds [Sat, 25 Jul 2015 00:00:04 +0000 (17:00 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Four smaller fixes for the current series. This contains:
- A fix for clones of discard bio's, that can cause data corruption.
From Martin.
- A fix for null_blk, where in certain queue modes it could access a
request after it had been freed. From Mike Krinkin.
- An error handling leak fix for blkcg, from Tejun.
- Also from Tejun, export of the functions that a file system needs
to implement cgroup writeback support"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: Do a full clone when splitting discard bios
block: export bio_associate_*() and wbc_account_io()
blkcg: fix gendisk reference leak in blkg_conf_prep()
null_blk: fix use-after-free problem
Linus Torvalds [Fri, 24 Jul 2015 23:54:59 +0000 (16:54 -0700)]
Merge branch 'for-4.2-fixes' of git://git./linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"A couple important fixes.
- A block layer change which removed restriction on max transfer size
led to silent data corruption on some devices. A new quirk is
added to restore the old size limit for the reported device. If it
gets reported on more devices, we might have to consider restoring
the restriction for ATA devices by default.
- There finally is a SSD which is confirmed to cause data corruption
on TRIM regardless of which flavor is used. A new quirk is added
and the device is blacklisted
- Other device-specific workarounds"
* 'for-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: Do not blacklist M510DC
libata: increase the timeout when setting transfer mode
libata: add ATA_HORKAGE_MAX_SEC_1024 to revert back to previous max_sectors limit
libata: force disable trim for SuperSSpeed S238
libata: add ATA_HORKAGE_NOTRIM
libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for HP 250GB SATA disk VB0250EAVER
ata: pmp: add quirk for Marvell 4140 SATA PMP
Linus Torvalds [Fri, 24 Jul 2015 23:43:16 +0000 (16:43 -0700)]
Merge tag 'mmc-4.2-rc3' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fixes from Ulf Hansson:
"Here are some mmc fixes intended for v4.2 rc4.
Note, most of the changes are for the sdhci-esdhc-imx controller,
which also required us to modify some related DTS files. Those
changes have been acked by the SoC maintainer.
MMC core:
- Fix a reference inbalance issue for power_ro_lock_show() sysfs handler
MMC host:
- omap_hsmmc: Fix IRQ errorhandling for CD, DTO, and CRC
- sdhci: Prevent a kernel panic while using DMA
- mtk-sd: Let it depend on HAS_DMA to prevent build errors
- sdhci-esdhc: Make 8BIT bus work
- sdhci-esdhc-imx: Fix some regressions for DT based platforms
- sdhci-pxav3: Fix a regression for DT based platforms"
* tag 'mmc-4.2-rc3' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: sdhci-pxav3: fix platform_data is not initialized
dts: mmc: fsl-imx-esdhc: remove fsl,cd-controller support
mmc: sdhci-esdhc-imx: clear f_max in boarddata
mmc: sdhci-esdhc-imx: remove duplicated dts parsing
mmc: sdhci: make max-frequency property in device tree work
mmc: sdhci-esdhc-imx: move all non dt probe code into one function
mmc: sdhci-esdhc-imx: fix cd regression for dt platform
dts: imx7: fix sd card gpio polarity specified in device tree
dts: imx25: fix sd card gpio polarity specified in device tree
dts: imx6: fix sd card gpio polarity specified in device tree
dts: imx53: fix sd card gpio polarity specified in device tree
dts: imx51: fix sd card gpio polarity specified in device tree
mmc: sdhci-esdhc: Make 8BIT bus work
mmc: block: Add missing mmc_blk_put() in power_ro_lock_show()
mmc: MMC_MTK should depend on HAS_DMA
mmc: sdhci check parameters before call dma_free_coherent
mmc: omap_hsmmc: Handle BADA, DEB and CEB interrupts
mmc: omap_hsmmc: Fix DTO and DCRC handling
Linus Torvalds [Fri, 24 Jul 2015 23:33:11 +0000 (16:33 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"A fix for the warnings/oops when handling HID devices with "unnamed"
LEDs and couple of other driver fixups""
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: goodix - fix touch coordinates on WinBook TW100 and TW700
Input: LEDs - skip unnamed LEDs
Input: usbtouchscreen - avoid unresponsive TSC-30 touch screen
Input: elantech - force resolution of 31 u/mm
Input: zforce - don't overwrite the stack
Linus Torvalds [Fri, 24 Jul 2015 20:14:06 +0000 (13:14 -0700)]
Merge tag 'regulator-fix-v4.2-rc3' of git://git./linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"As well as some driver specific fixes there's several fixes here for
the core support for regulators supplying other regulators fixing both
an issue with ACPI support (which had never been tested before) and
some error handling and device removal issues that Javier noticed"
* tag 'regulator-fix-v4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: Fix memory leak in regulator_resolve_supply()
regulator: core: Increase refcount for regulator supply's module
regulator: core: Handle full constraints systems when resolving supplies
regulator: 88pm800: fix LDO vsel_mask value
regulator: max8973: Fix up control flag option for bias control
regulator: s2mps11: Fix GPIO suspend enable shift wrapping bug
Linus Torvalds [Fri, 24 Jul 2015 20:13:28 +0000 (13:13 -0700)]
Merge tag 'spi-fix-v4.2-rc3' of git://git./linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A small collection of pretty much unremarkable driver specific fixes
here plus the addition of a new device ID to spidev which requires no
other code changes"
* tag 'spi-fix-v4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: imx: Fix small DMA transfers
spi: zynq: missing break statement
spi: SPI_ZYNQMP_GQSPI should depend on HAS_DMA
spi: spidev: add compatible value for LTC2488
spi: img-spfi: fix support for speeds up to 1/4th input clock
Linus Torvalds [Fri, 24 Jul 2015 19:50:19 +0000 (12:50 -0700)]
Merge tag 'sound-4.2-rc4' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This has been a calm week again: one minor lockdep fix for PCM core,
and the most of the rest are HD-audio quirks and fixups for various
chips and machines"
* tag 'sound-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Add headset mic pin quirk for a Dell device
ALSA: hda - remove one pin from ALC292_STANDARD_PINS
ALSA: hda - Add new GPU codec ID 0x10de007d to snd-hda
ALSA: hda: add new AMD PCI IDs with proper driver caps
ALSA: hda - Fix Skylake codec timeout
ALSA: hda - Add headset mic support for Acer Aspire V5-573G
ALSA: sparc: Add missing kfree in error path
ALSA: pcm: Fix lockdep warning with nonatomic PCM ops
Linus Torvalds [Fri, 24 Jul 2015 19:44:24 +0000 (12:44 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- kernel crash fixes for multitouch and wacom drivers, by Brent Adam
and Dan Carpenter
- cp2112 data packet race condition corruption fix, by Antonio Borneo
- a few new device IDs for wacom and microsoft drivers
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: cp2112: fix to force single data-report reply
HID: wacom: Enable pad device for older Bamboo Touch tablets
HID: multitouch: Fix fields from pen report ID being interpreted for multitouch
HID: microsoft: Add quirk for MS Surface Type/Touch cover
HID: wacom: NULL dereferences on error in probe()
Linus Torvalds [Fri, 24 Jul 2015 19:37:29 +0000 (12:37 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Aome amdgpu, one i915, one ttm and one hlcdc, nothing too scary.
All seems fine for about this time"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/ttm: recognize ARM64 arch in ioprot handler
drm/amdgpu/cz/dpm: properly report UVD and VCE clock levels
drm/amdgpu/cz: implement voltage validation properly
drm/amdgpu: add VCE harvesting instance query
drm/amdgpu: implement VCE 3.0 harvesting support (v4)
drm/amdgpu/dce10: Re-set VBLANK interrupt state when enabling a CRTC
drm/amdgpu/dce11: Re-set VBLANK interrupt state when enabling a CRTC
drm: Stop resetting connector state to unknown
drm/i915: Use two 32bit reads for select 64bit REG_READ ioctls
drm: atmel-hlcdc: fix vblank initial state
Linus Torvalds [Fri, 24 Jul 2015 19:31:30 +0000 (12:31 -0700)]
Merge branch 'stable' of git://git./linux/kernel/git/cmetcalf/linux-tile
Pull arch/tile bugfix from Chris Metcalf:
"This fixes a bug in freeing the initramfs memory"
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: use free_bootmem_late() for initrd
Linus Torvalds [Fri, 24 Jul 2015 19:23:06 +0000 (12:23 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Everything related to the new quirks and memory type features:
- small improvements to the quirks API
- extending one of the quirks from just AMD to Intel as well, because
4.2 can show the same problem with problematic firmware on Intel
too"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: rename quirk constants to KVM_X86_QUIRK_*
KVM: vmx: obey KVM_QUIRK_CD_NW_CLEARED
KVM: x86: introduce kvm_check_has_quirk
KVM: MTRR: simplify kvm_mtrr_get_guest_memory_type
KVM: MTRR: fix memory type handling if MTRR is completely disabled
Steven Rostedt (Red Hat) [Fri, 24 Jul 2015 14:38:12 +0000 (10:38 -0400)]
ftrace: Fix breakage of set_ftrace_pid
Commit
4104d326b670 ("ftrace: Remove global function list and call function
directly") simplified the ftrace code by removing the global_ops list with a
new design. But this cleanup also broke the filtering of PIDs that are added
to the set_ftrace_pid file.
Add back the proper hooks to have pid filtering working once again.
Cc: stable@vger.kernel.org # 3.16+
Reported-by: Matt Fleming <matt@console-pimps.org>
Reported-by: Richard Weinberger <richard.weinberger@gmail.com>
Tested-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Bastien Nocera [Fri, 24 Jul 2015 16:08:53 +0000 (09:08 -0700)]
Input: goodix - fix touch coordinates on WinBook TW100 and TW700
The touchscreen on the WinBook TW100 and TW700 don't match the default
display, with 0,0 touches being reported when touching at the bottom
right of the screen.
1280,800 0,800
+-------------+
| |
| |
| |
+-------------+
1280,0 0,0
It's unfortunately impossible to detect this problem with data from the
DSDT, or other auxiliary metadata, so fallback to quirking this specific
model of tablet instead.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dmitry Torokhov [Wed, 22 Jul 2015 21:56:39 +0000 (14:56 -0700)]
Input: LEDs - skip unnamed LEDs
Devices may declare more LEDs than what is known to input-leds
(HID does this for some devices). Instead of showing ugly warnings
on connect and, even worse, oopsing on disconnect, let's simply
ignore LEDs that are not known to us.
Reported-and-tested-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Mark Brown [Fri, 24 Jul 2015 15:19:50 +0000 (16:19 +0100)]
Merge remote-tracking branches 'spi/fix/gqspi', 'spi/fix/imx', 'spi/fix/mg-spfi' and 'spi/fix/spidev' into spi-linus
Mark Brown [Fri, 24 Jul 2015 15:19:25 +0000 (16:19 +0100)]
Merge remote-tracking branches 'regulator/fix/88pm800', 'regulator/fix/max8973', 'regulator/fix/s2mps11' and 'regulator/fix/supply' into regulator-linus
Mark Brown [Fri, 24 Jul 2015 15:19:25 +0000 (16:19 +0100)]
Merge remote-tracking branch 'regulator/fix/core' into regulator-linus
Sascha Hauer [Fri, 24 Jul 2015 13:01:08 +0000 (15:01 +0200)]
spi: imx: Fix small DMA transfers
DMA transfers must be greater than the watermark level size. spi_imx->rx_wml
and spi_imx->tx_wml contain the watermark level in 32bit words whereas struct
spi_transfer contains the transfer len in bytes. Fix the check if DMA is
possible for a transfer accordingly. This fixes transfers with sizes between
33 and 128 bytes for which previously was claimed that DMA is possible.
Fixes:
f62caccd12c17e4 (spi: spi-imx: add DMA support)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Denys Vlasenko [Fri, 24 Jul 2015 12:16:43 +0000 (14:16 +0200)]
x86/asm/entry/32: Revert 'Do not use R9 in SYSCALL32' commit
This change reverts most of commit
53e9accf0f 'Do not use R9 in
SYSCALL32'. I don't yet understand how, but code in that commit
sometimes fails to preserve EBP.
See https://bugzilla.kernel.org/show_bug.cgi?id=101061
"Problems while executing 32-bit code on AMD64"
Reported-and-tested-by: Krzysztof A. Sobiecki <sobkas@gmail.com>
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Will Drewry <wad@chromium.org>
Cc: Kees Cook <keescook@chromium.org>
CC: x86@kernel.org
Link: http://lkml.kernel.org/r/1437740203-11552-1-git-send-email-dvlasenk@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 24 Jul 2015 14:13:43 +0000 (16:13 +0200)]
x86/mm: Fix newly introduced printk format warnings
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Jingju Hou [Thu, 23 Jul 2015 09:56:23 +0000 (17:56 +0800)]
mmc: sdhci-pxav3: fix platform_data is not initialized
pdev->dev.platform_data is not initialized if match is true in function
sdhci_pxav3_probe. Just local variable pdata is assigned the return value
from function pxav3_get_mmc_pdata().
static int sdhci_pxav3_probe(struct platform_device *pdev) {
struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data;
...
if (match) {
ret = mmc_of_parse(host->mmc);
if (ret)
goto err_of_parse;
sdhci_get_of_property(pdev);
pdata = pxav3_get_mmc_pdata(dev);
}
...
}
Signed-off-by: Jingju Hou <houjingj@marvell.com>
Fixes:
b650352dd3df("mmc: sdhci-pxa: Add device tree support")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Dong Aisheng [Wed, 22 Jul 2015 12:53:10 +0000 (20:53 +0800)]
dts: mmc: fsl-imx-esdhc: remove fsl,cd-controller support
It's not supported by driver anymore after using runtime pm
and there's no user of it, so delete it now.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Dong Aisheng [Wed, 22 Jul 2015 12:53:09 +0000 (20:53 +0800)]
mmc: sdhci-esdhc-imx: clear f_max in boarddata
After commit
8d86e4fcccf6 ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
it's not used anymore.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Dong Aisheng [Wed, 22 Jul 2015 12:53:08 +0000 (20:53 +0800)]
mmc: sdhci-esdhc-imx: remove duplicated dts parsing
After commit
8d86e4fcccf6 ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
we do not need those duplicated parsing anymore.
Note: fsl,cd-controller is also deleted due to the driver does
not support controller card detection anymore after switch to runtime pm.
And there's no user of it right now in device tree.
wp-gpios is kept because we're still support fsl,wp-controller,
so we need a way to check if it's gpio wp or controller wp.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Dong Aisheng [Wed, 22 Jul 2015 12:53:07 +0000 (20:53 +0800)]
mmc: sdhci: make max-frequency property in device tree work
Device tree provides option to specify the max freqency with property
"max-frequency" in dts and common parse function mmc_of_parse() will
parse it and use this value to set host->f_max to tell the MMC core
the maxinum frequency the host works.
However, current sdhci driver will finally overwrite this value with
host->max_clk regardless of the max-frequency property.
This patch makes sure not overwrite the max-frequency set from device
tree and do basic sanity check.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Dong Aisheng [Wed, 22 Jul 2015 12:53:06 +0000 (20:53 +0800)]
mmc: sdhci-esdhc-imx: move all non dt probe code into one function
This is an incremental fix of commit
e62bd351b("mmc: sdhci-esdhc-imx: Do not break platform data boards").
After commit
8d86e4fcccf6 ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
we do not need to run the check of boarddata->wp_type/cd_type/max_bus_width
again for dt platform since those are already handled by mmc_of_parse().
Current code only exclude the checking of wp_type for dt platform which
does not make sense.
This patch moves all non dt probe code into one function.
Besides, since we only support SD3.0/eMMC HS200 for dt platform, the
support_vsel checking and ultra high speed pinctrl state are also merged
into sdhci_esdhc_imx_probe_dt.
Then we have two separately probe function for dt and non dt type.
This can make the driver probe more clearly.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Dong Aisheng [Wed, 22 Jul 2015 12:53:05 +0000 (20:53 +0800)]
mmc: sdhci-esdhc-imx: fix cd regression for dt platform
Current card detect probe process is that when driver finds a valid
ESDHC_CD_GPIO, it will clear the quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION
which is set by default for all esdhc/usdhc controllers.
Then host driver will know there's a valid card detect function.
Commit
8d86e4fcccf6 ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()")
breaks GPIO CD function for dt platform that it will return directly
when find ESDHC_CD_GPIO for dt platform which result in the later wrongly
to keep SDHCI_QUIRK_BROKEN_CARD_DETECTION for all dt platforms.
Then MMC_CAP_NEEDS_POLL will be used instead even there's a valid
GPIO card detect.
This patch adds back this function and follows the original approach to
clear the quirk if find an valid CD GPIO for dt platforms.
Fixes:
8d86e4fcccf6 ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()")
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Dong Aisheng [Wed, 22 Jul 2015 12:53:04 +0000 (20:53 +0800)]
dts: imx7: fix sd card gpio polarity specified in device tree
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Dong Aisheng [Wed, 22 Jul 2015 12:53:03 +0000 (20:53 +0800)]
dts: imx25: fix sd card gpio polarity specified in device tree
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Dong Aisheng [Wed, 22 Jul 2015 12:53:02 +0000 (20:53 +0800)]
dts: imx6: fix sd card gpio polarity specified in device tree
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Dong Aisheng [Wed, 22 Jul 2015 12:53:01 +0000 (20:53 +0800)]
dts: imx53: fix sd card gpio polarity specified in device tree
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Dong Aisheng [Wed, 22 Jul 2015 12:53:00 +0000 (20:53 +0800)]
dts: imx51: fix sd card gpio polarity specified in device tree
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Joakim Tjernlund [Wed, 22 Jul 2015 14:44:26 +0000 (16:44 +0200)]
mmc: sdhci-esdhc: Make 8BIT bus work
Support for 8BIT bus with was added some time ago to sdhci-esdhc but
then missed to remove the 8BIT from the reserved bit mask which made
8BIT non functional.
Fixes:
66b50a00992d ("mmc: esdhc: Add support for 8-bit bus width and..")
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tomas Winkler [Thu, 16 Jul 2015 13:50:45 +0000 (15:50 +0200)]
mmc: block: Add missing mmc_blk_put() in power_ro_lock_show()
Enclosing mmc_blk_put() is missing in power_ro_lock_show() sysfs handler,
let's add it.
Fixes:
add710eaa886 ("mmc: boot partition ro lock support")
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Geert Uytterhoeven [Fri, 26 Jun 2015 12:09:26 +0000 (14:09 +0200)]
mmc: MMC_MTK should depend on HAS_DMA
If NO_DMA=y:
ERROR: "dma_alloc_coherent" [drivers/mmc/host/mtk-sd.ko] undefined!
ERROR: "dma_unmap_sg" [drivers/mmc/host/mtk-sd.ko] undefined!
ERROR: "dma_map_sg" [drivers/mmc/host/mtk-sd.ko] undefined!
ERROR: "dma_free_coherent" [drivers/mmc/host/mtk-sd.ko] undefined!
Add a dependency on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Peng Fan [Mon, 22 Jun 2015 03:41:23 +0000 (11:41 +0800)]
mmc: sdhci check parameters before call dma_free_coherent
We should not call dma_free_coherent if host->adma_table is NULL,
otherwise may trigger panic.
Fixes:
d1e49f77d7c7 ("mmc: sdhci: convert ADMA descriptors to a...")
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Vignesh R [Tue, 16 Jun 2015 10:37:18 +0000 (16:07 +0530)]
mmc: omap_hsmmc: Handle BADA, DEB and CEB interrupts
Sometimes BADA, DEB or CEB error interrupts occur when sd card is
unplugged during data transfer. These interrupts are currently ignored
by the interrupt handler. But, this results in card not being
recognised on subsequent insertion. This is because mmcqd is waiting
forever for the data transfer(for which error occurred) to complete.
Fix this, by reporting BADA, DEB, CEB errors to mmc-core as -EILSEQ, so
that the core can do appropriate handling.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Kishon Vijay Abraham I [Tue, 16 Jun 2015 10:37:17 +0000 (16:07 +0530)]
mmc: omap_hsmmc: Fix DTO and DCRC handling
DTO/DCRC errors were not being informed to the mmc core since
commit
ae4bf788ee9b ("mmc: omap_hsmmc: consolidate error report handling of
HSMMC IRQ"). This commit made sure 'end_trans' is never set on DTO/DCRC
errors. This is because after this commit 'host->data' is checked after
it has been cleared to NULL by omap_hsmmc_dma_cleanup().
Because 'end_trans' is never set, omap_hsmmc_xfer_done() is never invoked
making core layer not to be aware of DTO/DCRC errors. Because of this
any command invoked after DTO/DCRC error leads to a hang.
Fix this by checking for 'host->data' before it is actually cleared.
Fixes:
ae4bf788ee9b ("mmc: omap_hsmmc: consolidate error report handling of
HSMMC IRQ")
CC: stable@vger.kernel.org
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Dave Airlie [Fri, 24 Jul 2015 04:27:44 +0000 (14:27 +1000)]
Merge tag 'drm-atmel-hlcdc/fixes-for-4.2' of https://github.com/bbrezillon/linux-at91 into drm-fixes
single hlcdc fix.
* tag 'drm-atmel-hlcdc/fixes-for-4.2' of https://github.com/bbrezillon/linux-at91:
drm: atmel-hlcdc: fix vblank initial state
NeilBrown [Fri, 17 Jul 2015 03:26:23 +0000 (13:26 +1000)]
md/raid5: clear R5_NeedReplace when no longer needed.
This flag is currently never cleared, which can in rare cases
trigger a warn-on if it is still set but the block isn't
InSync.
So clear it when it isn't need, which includes if the replacement
device has failed.
Signed-off-by: NeilBrown <neilb@suse.com>
Goldwyn Rodrigues [Wed, 24 Jun 2015 14:30:32 +0000 (09:30 -0500)]
Fix read-balancing during node failure
During a node failure, We need to suspend read balancing so that the
reads are directed to the first device and stale data is not read.
Suspending writes is not required because these would be recorded and
synced eventually.
A new flag MD_CLUSTER_SUSPEND_READ_BALANCING is set in recover_prep().
area_resyncing() will respond true for the entire devices if this
flag is set and the request type is READ. The flag is cleared
in recover_done().
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reported-By: David Teigland <teigland@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Goldwyn Rodrigues [Wed, 1 Jul 2015 02:19:56 +0000 (12:19 +1000)]
md-cluster: fix bitmap sub-offset in bitmap_read_sb
bitmap_read_sb is modifying mddev->bitmap_info.offset. This works for
the first bitmap read. However, when multiple bitmaps need to be opened
by the same node, it ends up corrupting the offset. Fix it by using a
local variable.
Also, bitmap_read_sb is not required in bitmap_copy_from_slot since
it is called in bitmap_create. Remove bitmap_read_sb().
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Goldwyn Rodrigues [Wed, 22 Jul 2015 17:09:15 +0000 (12:09 -0500)]
md: Return error if request_module fails and returns positive value
request_module() can return 256 (process exited) in some cases,
which is not as specified in the documentation before the
request_module() definition. Convert the error to -ENOENT.
The positive error number results in bitmap_create() returning
a value that is meant to be an error but doesn't look like one,
so it is dereferenced as a point and causes a crash.
(not needed for stable as this is "experimental" code)
Fixes:
edb39c9deda8 ("Introduce md_cluster_operations to handle cluster functions")
Signed-off-By: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Goldwyn Rodrigues [Wed, 22 Jul 2015 17:09:16 +0000 (12:09 -0500)]
md: Skip cluster setup in case of error while reading bitmap
If the bitmap read fails, the error code set is -EINVAL. However,
we don't check for errors and go ahead with cluster_setup.
Skip the cluster setup in case of error.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.com>
NeilBrown [Thu, 23 Jul 2015 23:22:16 +0000 (09:22 +1000)]
md/raid1: fix test for 'was read error from last working device'.
When we get a read error from the last working device, we don't
try to repair it, and don't fail the device. We simple report a
read error to the caller.
However the current test for 'is this the last working device' is
wrong.
When there is only one fully working device, it assumes that a
non-faulty device is that device. However a spare which is rebuilding
would be non-faulty but so not the only working device.
So change the test from "!Faulty" to "In_sync". If ->degraded says
there is only one fully working device and this device is in_sync,
this must be the one.
This bug has existed since we allowed read_balance to read from
a recovering spare in v3.0
Reported-and-tested-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Fixes:
76073054c95b ("md/raid1: clean up read_balance.")
Cc: stable@vger.kernel.org (v3.0+)
Signed-off-by: NeilBrown <neilb@suse.com>
Dave Airlie [Fri, 24 Jul 2015 01:52:35 +0000 (11:52 +1000)]
Merge tag 'topic/drm-fixes-2015-07-23' of git://anongit.freedesktop.org/drm-intel into drm-fixes
Regression fix for systemd getting confused about unknown connector state
after resume. Just stop setting the state to unknown, turned out to be a
silly idea anyway. What drivers imo really should do (and i915 still does
that) is forcing a full reprobe on resume to make sure connector changes
while suspended are caught. Most drivers seem to get this wrong. Otoh it
took us years to get fixes merged where some probe races resulted in
eating uevents, I guess userspace expectations for reliable hpd are just
really low :(
* tag 'topic/drm-fixes-2015-07-23' of git://anongit.freedesktop.org/drm-intel:
drm: Stop resetting connector state to unknown
Dave Airlie [Fri, 24 Jul 2015 01:52:09 +0000 (11:52 +1000)]
Merge tag 'drm-intel-fixes-2015-07-23' of git://anongit.freedesktop.org/drm-intel into drm-fixes
arb_timer kernel side fix from Chris.
* tag 'drm-intel-fixes-2015-07-23' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Use two 32bit reads for select 64bit REG_READ ioctls
Dave Airlie [Fri, 24 Jul 2015 01:51:18 +0000 (11:51 +1000)]
Merge branch 'drm-fixes-4.2' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Some amdgpu fixes.
* 'drm-fixes-4.2' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu/cz/dpm: properly report UVD and VCE clock levels
drm/amdgpu/cz: implement voltage validation properly
drm/amdgpu: add VCE harvesting instance query
drm/amdgpu: implement VCE 3.0 harvesting support (v4)
drm/amdgpu/dce10: Re-set VBLANK interrupt state when enabling a CRTC
drm/amdgpu/dce11: Re-set VBLANK interrupt state when enabling a CRTC
Alexandre Courbot [Wed, 1 Jul 2015 08:32:29 +0000 (17:32 +0900)]
drm/ttm: recognize ARM64 arch in ioprot handler
Return proper pgprot for ARM64. This is required for objects like
Nouveau fences to be mapped with expected coherency.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Peter Hurley [Mon, 13 Jul 2015 02:49:13 +0000 (22:49 -0400)]
pty: Add debug message for ptmx open
Opens of /dev/ptmx don't use tty_open() so debug messages are
not printed for those opens; print a debug message with the
open count (which must always be 1) if TTY_DEBUG_HANGUP is defined.
NB: Each tty core source file undefs support for debug messages.
The relevant source file must be patched/edited to enable these
messages.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Mon, 13 Jul 2015 02:49:12 +0000 (22:49 -0400)]
tty: core: Improve ldisc debug messages
Add debug messages for ldisc open and close, and remove
"closing ldisc" message from tty_ldisc_release(), because a
close message is now printed for both ldiscs; always print ldisc
pointer first so ldisc changes are easier to identify.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Mon, 13 Jul 2015 02:49:11 +0000 (22:49 -0400)]
tty: Replace inline #ifdef TTY_DEBUG_WAIT_UNTIL_SENT
Add tty_debug_wait_until_sent() macro which uses tty_debug() to print
the debug message; remove inlined #ifdef.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Mon, 13 Jul 2015 02:49:10 +0000 (22:49 -0400)]
tty: Use tty_debug() for tty_ldisc_debug()
Replace tty_ldisc_debug() macro definition; substitute with equivalent
tty_debug() invocation.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Mon, 13 Jul 2015 02:49:09 +0000 (22:49 -0400)]
tty: Replace #ifdef TTY_DEBUG_HANGUP with tty_debug_hangup()
Add tty_debug_hangup() macro which uses tty_debug to print the
debug message; remove inlined #ifdefs.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Mon, 13 Jul 2015 02:49:08 +0000 (22:49 -0400)]
tty: core: Add tty_debug() for printk(KERN_DEBUG) messages
Introduce tty_debug() macro to output uniform debug information for
tty core debug messages (function name and tty name).
Note: printk(KERN_DEBUG) is retained here over pr_debug() since
messages can be enabled in non-DEBUG builds.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Mon, 13 Jul 2015 02:49:07 +0000 (22:49 -0400)]
tty: core: Improve debug message content
Output the function name, tty name, and invariant failure (if applicable).
Add the tty count to the tty_open() message. Fix the disassociate_ctty()
message, which printed the NULL pointer and the wrong message.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Gortmaker [Wed, 22 Jul 2015 02:02:18 +0000 (22:02 -0400)]
drivers/tty: make serial/sunhv.c driver explicitly non-modular
The Kconfig for this driver is currently:
config SERIAL_SUNHV
bool "Sun4v Hypervisor Console support"
...meaning that it currently is not being built as a module by
anyone. Lets remove the modular and unused code here, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't swap module.h for init.h since this file has init.h already.
We leave some tags like MODULE_LICENSE for documentation purposes, and
for the "git blame" value. Also note that MODULE_DEVICE_TABLE is a
no-op for non-modular code, so we remove that too.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: sparclinux@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Gortmaker [Wed, 22 Jul 2015 02:02:17 +0000 (22:02 -0400)]
drivers/tty: make serial/suncore.c driver explicitly non-modular
The Kconfig for this driver is currently:
config SERIAL_SUNCORE
bool
...meaning that it currently is not being built as a module by
anyone. Lets remove the modular and unused code here, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't swap module.h for init.h since this file has init.h already.
We leave some tags like MODULE_LICENSE for documentation purposes, and
for the "git blame" value.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: sparclinux@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Gortmaker [Wed, 22 Jul 2015 02:02:16 +0000 (22:02 -0400)]
drivers/tty: make serial/lantic.c driver explicitly non-modular
The Kconfig for this option is currently:
config SERIAL_LANTIQ
bool "Lantiq serial driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity, so that when reading the
driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We delete the MODULE_DESCRIPTION and LICENSE tags since they are
not adding any new information above and beyond what is at the top
of the file. Also note that MODULE_DEVICE_TABLE is a no-op for
non-modular code, so we remove that as well.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Gortmaker [Wed, 22 Jul 2015 02:02:15 +0000 (22:02 -0400)]
drivers/tty: make serial/sn_console.c driver explicitly non-modular
The Kconfig for this option is currently:
config SERIAL_SGI_L1_CONSOLE
bool "SGI Altix L1 serial console support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the orphaned module code, so that when reading the
driver there is no doubt it is builtin-only. We could consider
making it tristate, but the above bool has been there since before
the start of git history, which isn't all that surprising, since
consoles are typically critical to have at early boot. So adding
tristate is really of no value here.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Javier Martinez Canillas [Mon, 13 Jul 2015 11:18:51 +0000 (13:18 +0200)]
serial: samsung: Remove redundant DEBUG_LL check
Commit
84f57d9e3685 ("tty: serial/samsung: fix modular build") fixed
build issues when the driver was built as a module. One of those was
that printascii is only accessible when the driver is built-in.
But there is no need to check for defined(CONFIG_DEBUG_LL) since the
SERIAL_SAMSUNG_DEBUG Kconfig symbol already depends on DEBUG_LL.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Mon, 13 Jul 2015 00:50:50 +0000 (20:50 -0400)]
tty: buffers: Move hidden buffer index advance into outer loop
The advance of the 'read' buffer index belongs in the outer
flip buffer consume loop, with the other buffer index arithmetic.
No functional change.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Mon, 13 Jul 2015 00:50:49 +0000 (20:50 -0400)]
tty: Replace smp_rmb/smp_wmb with smp_load_acquire/smp_store_release
Clarify flip buffer producer/consumer operation; the use of
smp_load_acquire() and smp_store_release() more clearly indicates
which memory access requires a barrier.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Mon, 13 Jul 2015 00:47:35 +0000 (20:47 -0400)]
tty: vt: Fix !TASK_RUNNING diagnostic warning from paste_selection()
Pasting text with gpm on a VC produced warning [1]. Reset task state
to TASK_RUNNING in the paste_selection() loop, if the loop did not
sleep.
[1]
WARNING: CPU: 6 PID: 1960 at /home/peter/src/kernels/mainline/kernel/sched/core.c:7286 __might_sleep+0x7f/0x90()
do not call blocking ops when !TASK_RUNNING; state=1 set at [<
ffffffff8151805e>] paste_selection+0x9e/0x1a0
Modules linked in: btrfs xor raid6_pq ufs qnx4 hfsplus hfs minix ntfs msdos jfs xfs libcrc32c .....
CPU: 6 PID: 1960 Comm: gpm Not tainted 4.1.0-rc7+tty-xeon+debug #rc7+tty
Hardware name: Dell Inc. Precision WorkStation T5400 /0RW203, BIOS A11 04/30/2012
ffffffff81c9c0a0 ffff8802b0fd3ac8 ffffffff8185778a 0000000000000001
ffff8802b0fd3b18 ffff8802b0fd3b08 ffffffff8108039a ffffffff82ae8510
ffffffff81c9ce00 0000000000000015 0000000000000000 0000000000000000
Call Trace:
[<
ffffffff8185778a>] dump_stack+0x4f/0x7b
[<
ffffffff8108039a>] warn_slowpath_common+0x8a/0xc0
[<
ffffffff81080416>] warn_slowpath_fmt+0x46/0x50
[<
ffffffff810ddced>] ? __lock_acquire+0xe2d/0x13a0
[<
ffffffff8151805e>] ? paste_selection+0x9e/0x1a0
[<
ffffffff8151805e>] ? paste_selection+0x9e/0x1a0
[<
ffffffff810ad4ff>] __might_sleep+0x7f/0x90
[<
ffffffff8185f76a>] down_read+0x2a/0xa0
[<
ffffffff810bb1d8>] ? sched_clock_cpu+0xb8/0xe0
[<
ffffffff8150d1dc>] n_tty_receive_buf_common+0x4c/0xba0
[<
ffffffff810dc875>] ? mark_held_locks+0x75/0xa0
[<
ffffffff81861c95>] ? _raw_spin_unlock_irqrestore+0x65/0x80
[<
ffffffff810b49a1>] ? get_parent_ip+0x11/0x50
[<
ffffffff8150dd44>] n_tty_receive_buf2+0x14/0x20
[<
ffffffff81518117>] paste_selection+0x157/0x1a0
[<
ffffffff810b77b0>] ? wake_up_state+0x20/0x20
[<
ffffffff815203f8>] tioclinux+0xb8/0x2c0
[<
ffffffff81515bfe>] vt_ioctl+0xaee/0x11a0
[<
ffffffff810baf75>] ? sched_clock_local+0x25/0x90
[<
ffffffff810bbe11>] ? vtime_account_user+0x91/0xa0
[<
ffffffff8150810c>] tty_ioctl+0x20c/0xe20
[<
ffffffff810bbe11>] ? vtime_account_user+0x91/0xa0
[<
ffffffff810b49a1>] ? get_parent_ip+0x11/0x50
[<
ffffffff810b4a69>] ? preempt_count_sub+0x49/0x50
[<
ffffffff811ab71c>] ? context_tracking_exit+0x5c/0x290
[<
ffffffff811ab71c>] ? context_tracking_exit+0x5c/0x290
[<
ffffffff81248b98>] do_vfs_ioctl+0x318/0x570
[<
ffffffff810dca8d>] ? trace_hardirqs_on+0xd/0x10
[<
ffffffff810dc9b5>] ? trace_hardirqs_on_caller+0x115/0x1e0
[<
ffffffff81254acc>] ? __fget_light+0x6c/0xa0
[<
ffffffff81248e71>] SyS_ioctl+0x81/0xa0
[<
ffffffff81862832>] system_call_fastpath+0x16/0x7a
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Mon, 13 Jul 2015 01:05:26 +0000 (21:05 -0400)]
serial: core: Fix crashes while echoing when closing
While closing, new rx data may be received after the input buffers
have been flushed but before stop_rx() halts receiving [1]. The
new data might not be processed by flush_to_ldisc() until after
uart_shutdown() and normal input processing is re-enabled (ie.,
tty->closing = 0). The race is outlined below:
CPU 0 | CPU 1
|
uart_close() |
tty_port_close_start() |
tty->closing = 1 |
tty_ldisc_flush() |
| => IRQ
| while (LSR & data ready)
| uart_insert_char()
| tty_flip_buffer_push()
| <= EOI
stop_rx() | .
uart_shutdown() | .
free xmit.buf | .
tty_port_tty_set(NULL) | .
tty->closing = 0 | .
| flush_to_ldisc()
| n_tty_receive_buf_common()
| __receive_buf()
| ...
| commit_echoes()
| uart_flush_chars()
| __uart_start()
| ** OOPS on port.tty deref **
tty_ldisc_flush() |
Input processing must be prevented from echoing (tty->closing = 1)
until _after_ the input buffers have been flushed again at the end
of uart_close().
[1] In fact, some input may actually be buffered _after_ stop_rx()
since the rx interrupt may have already triggered but not yet been
handled when stop_rx() disables rx interrupts.
Fixes:
2e758910832d ("serial: core: Flush ldisc after dropping port
mutex in uart_close()")
Reported-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Thu, 9 Jul 2015 03:10:06 +0000 (23:10 -0400)]
m32r: Add ioreadXX/iowriteXX big-endian mmio accessors
commit
c627f2ceb692 ("serial: 8250: Add support for big-endian MMIO accesses")
added support for 32-bit big-endian mmio to the 8250 driver. Support for
ioreadXXbe/iowriteXXbe io accessors was missing from m32r arch, which caused
build errors.
Add trivial macro mmio accessors.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexander Stein [Thu, 9 Jul 2015 08:34:34 +0000 (10:34 +0200)]
serial/uuc_uart: Support higher bitrates than 115200 Bit/s
The maximum bitrate supported depends on the clock rate used in BRG.
This is stored in port.uartclk during probe. Respecting the 16x
oversampling higher bitrates can be supported.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Krzysztof Kozlowski [Fri, 10 Jul 2015 06:36:20 +0000 (15:36 +0900)]
tty: serial: Drop owner assignment from i2c_driver
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Krzysztof Kozlowski [Fri, 10 Jul 2015 06:36:19 +0000 (15:36 +0900)]
tty: serial: Drop owner assignment from platform_driver
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cyrille Pitchen [Thu, 2 Jul 2015 13:18:13 +0000 (15:18 +0200)]
tty/serial: at91: use 32bit writes into TX FIFO when DMA is enabled
For now this improvement is only used with TX DMA transfers. The data
width must be set properly when configuring the DMA controller. Also
the FIFO configuration must be set to match the DMA transfer data
width:
TXRDYM (Transmitter Ready Mode) and RXRDYM (Receiver Ready Mode) must
be set into the FIFO Mode Register. These values are used by the
USART to trigger the DMA controller. In single data mode they are not
used and should be reset to 0.
So the TXRDYM bits are changed to FOUR_DATA; then USART triggers the
DMA controller when at least 4 data can be written into the TX FIFO
througth the THR. On the other hand the RXRDYM bits are left unchanged
to ONE_DATA.
Atmel eXtended DMA controller allows us to set a different data width
for each part of a scatter-gather transfer. So when calling
dmaengine_slave_config() to configure the TX path, we just need to set
dst_addr_width to the maximum data width. Then DMA writes into THR are
split into up to two parts. The first part carries the first data to
be sent and has a length equal to the greatest multiple of 4 (bytes)
lower than or equal to the total length of the TX DMA transfer. The
second part carries the trailing data (up to 3 bytes). The first part
is written by the DMA into THR using 32 bit accesses, whereas 8bit
accesses are used for the second part.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cyrille Pitchen [Thu, 2 Jul 2015 13:18:12 +0000 (15:18 +0200)]
tty/serial: at91: add support to FIFOs
Depending on the hardware, TX and RX FIFOs may be available. The RX
FIFO can avoid receive overruns, especially when DMA transfers are
not used to read data from the Receive Holding Register. For heavy
system load, The CPU is likely not be able to fetch data fast enough
from the RHR.
In addition, the RX FIFO can supersede the DMA/PDC to control the RTS
line when the Hardware Handshaking mode is enabled. Two thresholds
are to be set for that purpose:
- When the number of data in the RX FIFO crosses and becomes lower
than or equal to the low threshold, the RTS line is set to low
level: the remote peer is requested to send data.
- When the number of data in the RX FIFO crosses and becomes greater
than or equal to the high threshold, the RTS line is set to high
level: the remote peer should stop sending new data.
- low threshold <= high threshold
Once these two thresholds are set properly, this new feature is
enabled by setting the FIFO RTS Control bit of the FIFO Mode Register.
FIFOs also introduce a new multiple data mode: the USART works either
in multiple data mode or in single data (legacy) mode.
If MODE9 bit is set into the Mode Register or if USMODE is set to
either LIN_MASTER, LIN_SLAVE or LON_MODE, FIFOs operate in single
data mode. Otherwise, they operate in multiple data mode.
In this new multiple data mode, accesses to the Receive Holding
Register or Transmit Holding Register slightly change.
Since this driver implements neither the 9bit data feature (MODE9 bit
set into the Mode Register) nor LIN modes, the USART works in
multiple data mode whenever FIFOs are available and enabled. We also
assume that data are 8bit wide.
In single data mode, 32bit access CAN be used to read a single data
from RHR or write a single data into THR.
However in multiple data mode, a 32bit access to RHR now allows us to
read four consecutive data from RX FIFO. Also a 32bit access to THR
now allows to write four consecutive data into TX FIFO. So we MUST
use 8bit access whenever only one data have to be read/written at a
time.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cyrille Pitchen [Thu, 2 Jul 2015 13:18:11 +0000 (15:18 +0200)]
tty/serial: at91: remove bunch of macros to access UART registers
This patch replaces the UART_PUT_*, resp. UART_GET_*, macros by
atmel_uart_writel(), resp. atmel_uart_readl(), inline function calls.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cyrille Pitchen [Thu, 2 Jul 2015 13:18:10 +0000 (15:18 +0200)]
tty/serial: at91: fix some macro definitions to fit coding style
This patch updates macro definitions in atmel_serial.h to fit the
80 column rule.
Please note that some deprecated comments such as "[AT91SAM9261 only]"
are removed as the corresponding bits also exist in some later chips.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cyrille Pitchen [Thu, 2 Jul 2015 13:18:09 +0000 (15:18 +0200)]
ARM: at91/dt: add a new DT property to support FIFOs on Atmel USARTs
This patch adds a new DT property, "atmel,fifo-size", to enable and set
the maximum number of data the RX and TX FIFOs can store on FIFO capable
USARTs.
Please be aware that the VERSION register can not be used to guess the
size of FIFOs. Indeed, for a given hardware version, the USARTs can be
integrated on Atmel SoCs with different FIFO sizes. Also the
"atmel,fifo-size" property is optional as older USARTs don't embed FIFO at
all.
Besides, the FIFO size can not be read or guessed from other registers:
When designing the FIFO feature, no dedicated registers were added to
store this size. Unsed spaces in the I/O register range are limited and
better reserved for future usages. Instead, the FIFO size of each
peripheral is documented in the programmer datasheet.
Finally, on a given SoC, there can be several instances of USART with
different FIFO sizes. This explain why we'd rather use a dedicated DT
property than use the "compatible" property.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patrick Donnelly [Sun, 12 Jul 2015 22:51:52 +0000 (18:51 -0400)]
tty: add missing rcu_read_lock for task_pgrp
task_pgrp requires an rcu or tasklist lock to be obtained if the returned pid
is to be dereferenced, which kill_pgrp does. Obtain an RCU lock for the
duration of use.
Signed-off-by: Patrick Donnelly <batrick@batbytes.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>