gxfb: use PCI_DEVICE() for gxfb's pci device table

Drop the class/class_mask stuff; it's unnecessary as long as the vendor and
device IDs match.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gxfb: don't enable the CRT DACs when we are in flatpanel mode

When the FP strap is enabled, don't turn on the CRT DACs - that will save
about 35 mA of power.

Updated/cleaned up by Andres Salomon.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gxfb: set the right registers to tweak the sync polarity

While running in flatpanel mode it is important to change the FP sync bits (VG
register 0x408) rather then the CRT sync bits (VG register 0x008).  This patch
keeps the CRT sync bits at default when a flatpanel exists.

Note that this also fixes inverted logic; we want CRT_VSYNC_POL to be set (ie,
vsync is normally high) when FB_SYNC_VERT_HIGH_ACT is unset.

Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

x86: GEODE: add Virtual Systems Architecture detection

This is generic VSA2 detection.  It's used by OLPC to determine whether or not
the BIOS contains VSA2, but since other BIOSes are coming out that don't use
the VSA (ie, tinybios), it might end up being useful for others.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

x86: geode: MSR cleanup

This cleans up a few MSR-using drivers in the following manner:
  - Ensures MSRs are all defined in asm/geode.h, rather than in misc
    places
  - Makes the naming consistent; cs553[56] ones begin with MSR_,
    GX-specific ones start with MSR_GX_, and LX-specific ones start
    with MSR_LX_.  Also, make the names match the data sheet.
  - Use MSR names rather than numbers in source code
  - Document the fact that the LX's MSR_PADSEL has the wrong value
    in the data sheet.  That's, uh, good to note.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbcon: replace mono_col macro with static inline

Use __u32 for max_len to match the declaration of length in the struct
fb_bitfield.

Suppresses sparse shadowed variable warnings from the nested max()
macros:
drivers/video/console/fbcon.h:130:8: warning: symbol '_x' shadows an earlier one
drivers/video/console/fbcon.h:130:8: originally declared here
drivers/video/console/fbcon.h:130:8: warning: symbol '_x' shadows an earlier one
drivers/video/console/fbcon.h:130:8: originally declared here
drivers/video/console/fbcon.h:130:8: warning: symbol '_y' shadows an earlier one
drivers/video/console/fbcon.h:130:8: originally declared here

[akpm@linux-foundation.org: fix constness]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pm2fb: correct error values returned from probe function

Fix error values returned in some code branches in the pm2fb_probe() function.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbdev: use DIV_ROUND_UP or roundup

The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.

An extract of the semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@haskernel@
@@

#include <linux/kernel.h>

@depends on haskernel@
expression n,d;
@@

(
- (n + d - 1) / d
+ DIV_ROUND_UP(n,d)
|
- (n + (d - 1)) / d
+ DIV_ROUND_UP(n,d)
)

@depends on haskernel@
expression n,d;
@@

- DIV_ROUND_UP((n),d)
+ DIV_ROUND_UP(n,d)

@depends on haskernel@
expression n,d;
@@

- DIV_ROUND_UP(n,(d))
+ DIV_ROUND_UP(n,d)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

powerpc: offb: add support for foreign endianness

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fb: add support for foreign endianness

Add support for the framebuffers with non-native endianness.  This is done via
FBINFO_FOREIGN_ENDIAN flag that will be used by the drivers.  Depending on the
host endianness this flag will be overwritten by FBINFO_BE_MATH internal flag,
or cleared.

Tested to work on MPC8360E-RDK (BE) + Fujitsu MINT framebuffer (LE).

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: <Valdis.Kletnieks@vt.edu>
Cc: Clemens Koller <clemens.koller@anagramm.de>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbdev: make the best-fit section of fb_find_mode return the closest matching mode

Currently, if a perfect match in terms of resolution is not found,
fb_find_mode() only looks for a best-fit mode among modes with a higher
resolution than the one requested.  Thus, if the user requests a resolution
higher than the largest supported one, they are dropped to the default mode
(usually a low resolution one).

Change this behaviour so that all valid video modes are considered when
looking for a best-fit mode, while still preferring modes with a higher
resolution.

Signed-off-by: Michal Januszewski <spock@gentoo.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gpiochip_reserve()

Add a new function gpiochip_reserve() to reserve ranges of gpios that platform
code has pre-allocated.  That is, this marks gpio numbers which will be
claimed by drivers that haven't yet been loaded, and thus are not available
for dynamic gpio number allocation.

[akpm@linux-foundation.org: remove unneeded __must_check]
[david-b@pacbell.net: don't export gpiochip_reserve (section fix)]
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gpiolib: dynamic gpio number allocation

If gpio_chip->base is negative during registration, gpiolib performs dynamic
base allocation.  This is useful for devices that aren't always present, such
as GPIOs on hotplugged devices rather than mainboards.  (This behavior was
previously specified but not implemented.)

To avoid using any numbers that may have been explicitly assigned but not yet
registered, this dynamic allocation assigns GPIO numbers from the biggest
number on down, instead of from the smallest on up.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gpio: define gpio_is_valid()

Introduce a gpio_is_valid() predicate; use it in gpiolib.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
    [ use inline function; follow the gpio_* naming convention;
      work without gpiolib; all programming interfaces need docs ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gpiolib: i2c/spi drivers: handle rmmod better

Use the newly introduced owner field in struct gpio_chip to protect the
current (small) set of non-SOC GPIO drivers from being unloaded while any of
their GPIOs are in use.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
[ add mcp23s08 and pcf857x ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gpiolib: better rmmod infrastructure

As long as one or more GPIOs on a gpio chip are used its driver should not be
unloaded.  The existing mechanism (gpiochip_remove failure) doesn't address
that, since rmmod can no longer be made to fail by having the cleanup code
report errors.  Module usecounts are the solution.

Assuming standard "initialize struct to zero" policies, this change won't
affect SOC platform drivers.  However, drivers for external chips (on I2C and
SPI busses) should be updated if they can be built as modules.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
[ gpio_ensure_requested() needs to update module usecounts too ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

i2o: remove static inline forward declarations

Nothing in between of them and the later declaration with body
needs them.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

isdn: rename CONFIG_AVMB1_COMPAT to not look like a Kconfig variable

Since CONFIG_AVMB1_COMPAT is not a Kconfig variable, move it out of the
Kconfig namespace.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

capifs: fix memory leak on remount

capifs_remount may reach 'return' statement without freeing of memory
allocated by kstrdup call

Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hisax: depend on CONFIG_PNP, not __ISAPNP__

The PNP driver interfaces depend on CONFIG_PNP, so test that rather than
__ISAPNP__.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

isdn: fix obvious cut-and-paste error in st5481_usb.c

Fix a rather obvious cut-and-paste error, where earlier code for the
controller URB got somehow mixed in with code for the interrupt URB.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

isdn: replace remaining __FUNCTION__ occurrences

__FUNCTION__ is gcc-specific, use __func__

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

eicon: fix sparse integer as NULL pointer warnings

drivers/isdn/hardware/eicon/message.c:745:47: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/eicon/message.c:761:45: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/eicon/message.c:9122:16: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/eicon/message.c:9147:16: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/eicon/message.c:9173:14: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/eicon/divasmain.c:396:23: warning: Using plain integer as NULL pointer

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

avm: fix sparse warning using integer as NULL pointer

drivers/isdn/hardware/avm/b1isa.c:206:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1isa.c:208:33: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1.c:664:42: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1.c:666:44: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1.c:668:42: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1.c:791:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1.c:793:33: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1pci.c:385:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1pci.c:387:33: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1dma.c:886:42: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1dma.c:888:44: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1dma.c:890:42: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1dma.c:973:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1dma.c:975:33: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1pcmcia.c:204:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1pcmcia.c:206:33: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/t1isa.c:554:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/t1isa.c:556:33: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/t1pci.c:236:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/t1pci.c:238:33: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/c4.c:1091:42: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/c4.c:1093:44: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/c4.c:1095:42: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/c4.c:1170:21: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/c4.c:1294:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/c4.c:1296:33: warning: Using plain integer as NULL pointer

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

capi: fix sparse warnings using integer as NULL pointer

drivers/isdn/capi/kcapi.c:829:30: warning: Using plain integer as NULL pointer
drivers/isdn/capi/kcapi.c:838:27: warning: Using plain integer as NULL pointer
drivers/isdn/capi/kcapi.c:954:17: warning: Using plain integer as NULL pointer
drivers/isdn/capi/kcapi.c:1007:37: warning: Using plain integer as NULL pointer
drivers/isdn/capi/kcapi.c:1009:33: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capiutil.c:453:24: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capilib.c:47:30: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:353:29: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:369:15: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:486:48: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:515:46: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:541:47: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:692:47: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:699:49: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:704:14: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:943:53: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:948:32: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:969:42: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:989:48: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:1026:69: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:1028:19: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:1061:20: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:1529:37: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:1531:33: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:338:15: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:758:32: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:880:40: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:407:15: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:429:49: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:407:15: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:444:49: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:429:49: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:429:49: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:429:49: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:429:49: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:429:49: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:1664:61: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:1969:37: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:2294:37: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:2297:33: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:2338:37: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:2341:33: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capifs.c:192:37: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capifs.c:194:33: warning: Using plain integer as NULL pointer

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

quota: convert stub functions from macros into inlines

Fixes things like this:

fs/super.c: In function `deactivate_super':
fs/super.c:182: warning: statement with no effect
fs/super.c: In function `do_remount_sb':
fs/super.c:644: warning: statement with no effect

Cc: Jan Kara <jack@ucw.cz>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

quota: reiserfs: make reiserfs handle quotaon on remount

Update reiserfs to handle quotaon on remount RW.

Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

quota: ext4: make ext4 handle quotaon on remount

Update ext4 to handle quotaon on remount RW.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

quota: ext3: make ext3 handle quotaon on remount

Update ext3 handle quotaon on remount RW.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

quota: quota core changes for quotaon on remount

Currently, we just turn quotas off on remount of filesystem to read-only
state.  The patch below adds necessary framework so that we can turn quotas
off on remount RO but we are able to automatically reenable them again when
filesystem is remounted to RW state.  All we need to do is to keep references
to inodes of quota files when remounting RO and using these references to
reenable quotas when remounting RW.

Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

quota: various style cleanups

Cleanups in quota code:
  Change __inline__ to inline.
  Change some macros to inline functions.
  Remove vfs_quota_off_mount() macro.
  DQUOT_OFF() should be (0) is CONFIG_QUOTA is disabled.
  Move declaration of mark_dquot_dirty and dirty_dquot from quota.h to dquot.c

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

quota: remove superfluous DQUOT_OFF() in fs/namespace.c

We don't need to turn quotas off before remounting root ro, because
do_remount_sb() already handles this.

Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

quota: do not allow setting of quota limits to too high values

We should check whether quota limits set via Q_SETQUOTA are not exceeding
limits which quota format is able to handle.

Signed-off-by: Andrew Perepechko <andrew.perepechko@sun.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kprobes: update document about batch registration

Add the description of batch registration interfaces to
Documentation/kprobes.txt.

Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: David Miller <davem@davemloft.net>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kprobes: add (un)register_jprobes for batch registration

Introduce unregister_/register_jprobes() for jprobe batch registration.

Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: David Miller <davem@davemloft.net>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kprobes: add (un)register_kretprobes for batch registration

Introduce unregister_/register_kretprobes() for kretprobe batch registration.

Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: David Miller <davem@davemloft.net>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kprobes: add (un)register_kprobes for batch registration

Introduce unregister_/register_kprobes() for kprobe batch registration.  This
can reduce waiting time for synchronized_sched() when a lot of probes have to
be unregistered at once.

Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: David Miller <davem@davemloft.net>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

list.h: add list_is_singular()

Add list_is_singular() to check a list has just one entry.

list_is_singular() is useful to check whether a list_head which have been
temporarily allocated for listing objects can be released or not.

Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kprobes: prevent probing of preempt_schedule()

Prohibit users from probing preempt_schedule().  One way of prohibiting the
user from probing functions is by marking such functions with __kprobes.  But
this method doesn't work for those functions, which are already marked to
different section like preempt_schedule() (belongs to __sched section).  So we
use blacklist approach to refuse user from probing these functions.

In blacklist approach we populate the blacklisted function's starting address
and its size in kprobe_blacklist structure.  Then we verify the user specified
address against start and end of the blacklisted function.  So any attempt to
register probe on blacklisted functions will be rejected.

[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Srinivasa DS <srinivasa@in.ibm.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

VT notifier extension for accessibility

Some accessibility modules need to be able to catch the output on the
console before the VT interpretation, and possibly swallow it.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mfd: use shorter set_current_state()

Since this routine declares a separate "tsk" pointer for no other reason than
to call set_task_state(), get rid of it and just invoke set_current_state().

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Nicolas Pitre <nico@cam.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sm501: add uart support

This patch extends the sm501 mfd with 8250 uart support. We're currently
doing this in the board specific r2d-1 code already, but it would be nice to
do move things into the mfd since it's more chip specific than board specific.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi: spi_imx updates

Updates to the i.MX SPI controller driver:

 1) Some comments changed and/or added.

 2) End of transfers is now managed on TXFIFO empty interrupt after the
    last write to TXFIFO.  This speeds interrupt execution by removing
    the wait for TXFIFO to become empty.  On TXFIFO empty interrupt the
    handler needs only to poll for the end of the ongoing transaction
    (SPI_CONTROL_XCH) to close the transfer.
     (2.1) Write only transfers are closed flushing RXFIFO.
     (2.2) Read transfers are closed reading trailing bytes from RXFIFO.
     (2.3) Read transfers where RXFIFO overrun occurred are closed by
           flushing RXFIFO and aborting the message.

 3) Fifos are now flushed via SPI disable after the end of ongoing
    transaction.

Signed-off-by: Andrea Paterniani <a.paterniani@swapp-eng.it>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

atmel_spi: support zero length transfer

A spi transfer with zero length is not invalid.  For example, such
transfer (len == 0 && delay_usecs != 0) can be used to achieve delay
before first CLK edge after chipselect assertion.

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi: replace remaining __FUNCTION__ occurrences

__FUNCTION__ is gcc-specific, use __func__

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

documentation: move spidev_fdx example to its own source file

Move sample source code to its own source file so that it can be used
easier and build-tested/check/maintained by anyone.

(Makefile changes are in a separate patch for all of Documentation/.)

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi: pxa2xx_spi "sparse" fixes

Various cleanups to pxa2xx_spi suggested by "sparse": make sure that
register addresess are "void __iomem *", and make a few functions properly
static.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ned Forrester <nforrester@whoi.edu>
Cc: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi: use menuconfig for CONFIG_SPI

Signed-off-by: Alessandro Guido <alessandro.guido@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

oprofile: change cpu_buffer from array to per_cpu variable

Change cpu_buffer from array to per_cpu variable in oprofile functions.

[akpm@linux-foundation.org: coding-style fixes]
Cc: Philippe Elie <phil.el@wanadoo.fr>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

x86: configurable DMI scanning code

Turn CONFIG_DMI into a selectable option if EMBEDDED is defined, in
order to be able to remove the DMI table scanning code if it's not
needed, and then reduce the kernel code size.

With CONFIG_DMI (i.e before) :

   text    data     bss     dec     hex filename
1076076  128656   98304 1303036  13e1fc vmlinux

Without CONFIG_DMI (i.e after) :

   text    data     bss     dec     hex filename
1068092  126308   98304 1292704  13b9a0 vmlinux

Result:

   text    data     bss     dec     hex filename
  -7984   -2348       0  -10332   -285c vmlinux

The new option appears in "Processor type and features", only when
CONFIG_EMBEDDED is defined.

This patch is part of the Linux Tiny project, and is based on previous work
done by Matt Mackall <mpm@selenic.com>.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Anvin" <hpa@zytor.com>
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/acpi/thermal.c: fix build with CONFIG_DMI=n

drivers/acpi/thermal.c: In function 'acpi_thermal_init':
drivers/acpi/thermal.c:1794: error: 'thermal_dmi_table' undeclared (first use in this function)
drivers/acpi/thermal.c:1794: error: (Each undeclared identifier is reported only once
drivers/acpi/thermal.c:1794: error: for each function it appears in.)

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

atmel_serial: remove duplicated macro definition

After commit 39d4c922b596633da86878b1a5cc881785b8e5fa (atmel_serial: fix
uart/console concurrent access) the UART_GET_TCR macro got redefined. This
patch removes the duplicated definition.

Signed-off-by: michael trimarchi <trimarchimichael@evidence.eu.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

serial: use time_before, time_before_eq, etc

The functions time_before, time_before_eq, time_after, and time_after_eq
are more robust for comparing jiffies against other values.

A simplified version of the semantic patch making this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@ change_compare_np @
expression E;
@@

(
- jiffies <= E
+ time_before_eq(jiffies,E)
|
- jiffies >= E
+ time_after_eq(jiffies,E)
|
- jiffies < E
+ time_before(jiffies,E)
|
- jiffies > E
+ time_after(jiffies,E)
)

@ include depends on change_compare_np @
@@

#include <linux/jiffies.h>

@ no_include depends on !include && change_compare_np @
@@

  #include <linux/...>
+ #include <linux/jiffies.h>
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

serial 8250: tighten test for using backup timer

Thomas Koeller had reported an issue where a device that had been making use
of the UART_BUG_TXEN code in the 8250 driver was mistakenly being caught by
the backup timer test, causing the device to work improperly.

To fix this, tighten the test requirements to enable the backup timer
workaround.

The backup timer is really meant to catch UARTs that don't re-assert the THRE
interrupt.  The expectation is that they do initially assert THRE.  This patch
clarifies the test.

Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Cc: Thomas Koeller <thomas@koeller.dyndns.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

serial: add VR41xx SIU setup for serial console

Add VR41xx SIU setup for serial console.

Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

serial: add vr41xx_siu_early_setup() for serial console

Add vr41xx_siu_early_setup() for serial console.

Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

uart_get_baud_rate: stop mangling termios

Russell King noticed this one: We have to avoid replacing B0 when we pick a
baud rate for a "hung up" port.  Ugly but the proper fix is in the tty layer
and means changing the tty<->serial interfaces so we will defer that for now.

[akpm@linux-foundation.org: fix uninitialised var]
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix tty speed handling on 8250

We try and write the correct speed back but the serial midlayer already
mangles the speed on us and that means if we request B0 we report back B9600
when we should not.  For now we'll hack around this in the drivers and serial
code, pending a better long term solution.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

char: make functions static in synclinkmp.c

All were forward declared with static.

Fixes sparse warnings:
drivers/char/synclinkmp.c:1476:5: warning: symbol 'read_proc' was not declared. Should it be static?
drivers/char/synclinkmp.c:2027:5: warning: symbol 'bh_action' was not declared. Should it be static?
drivers/char/synclinkmp.c:2058:6: warning: symbol 'bh_handler' was not declared. Should it be static?
drivers/char/synclinkmp.c:2103:6: warning: symbol 'bh_receive' was not declared. Should it be static?
drivers/char/synclinkmp.c:2112:6: warning: symbol 'bh_transmit' was not declared. Should it be static?
drivers/char/synclinkmp.c:2124:6: warning: symbol 'bh_status' was not declared. Should it be static?
drivers/char/synclinkmp.c:2136:6: warning: symbol 'isr_timer' was not declared. Should it be static?
drivers/char/synclinkmp.c:2162:6: warning: symbol 'isr_rxint' was not declared. Should it be static?
drivers/char/synclinkmp.c:2221:6: warning: symbol 'isr_rxrdy' was not declared. Should it be static?
drivers/char/synclinkmp.c:2351:6: warning: symbol 'isr_txint' was not declared. Should it be static?
drivers/char/synclinkmp.c:2379:6: warning: symbol 'isr_txrdy' was not declared. Should it be static?
drivers/char/synclinkmp.c:2410:6: warning: symbol 'isr_rxdmaok' was not declared. Should it be static?
drivers/char/synclinkmp.c:2427:6: warning: symbol 'isr_rxdmaerror' was not declared. Should it be static?
drivers/char/synclinkmp.c:2445:6: warning: symbol 'isr_txdmaok' was not declared. Should it be static?
drivers/char/synclinkmp.c:2463:6: warning: symbol 'isr_txdmaerror' was not declared. Should it be static?
drivers/char/synclinkmp.c:2480:6: warning: symbol 'isr_io_pin' was not declared. Should it be static?
drivers/char/synclinkmp.c:3420:5: warning: symbol 'alloc_dma_bufs' was not declared. Should it be static?
drivers/char/synclinkmp.c:3494:5: warning: symbol 'alloc_buf_list' was not declared. Should it be static?
drivers/char/synclinkmp.c:3553:5: warning: symbol 'alloc_frame_bufs' was not declared. Should it be static?
drivers/char/synclinkmp.c:3570:6: warning: symbol 'free_dma_bufs' was not declared. Should it be static?
drivers/char/synclinkmp.c:3580:5: warning: symbol 'alloc_tmp_rx_buf' was not declared. Should it be static?
drivers/char/synclinkmp.c:3588:6: warning: symbol 'free_tmp_rx_buf' was not declared. Should it be static?
drivers/char/synclinkmp.c:3594:5: warning: symbol 'claim_resources' was not declared. Should it be static?
drivers/char/synclinkmp.c:3681:6: warning: symbol 'release_resources' was not declared. Should it be static?
drivers/char/synclinkmp.c:3737:6: warning: symbol 'add_device' was not declared. Should it be static?
drivers/char/synclinkmp.c:3860:6: warning: symbol 'device_init' was not declared. Should it be static?
drivers/char/synclinkmp.c:4054:6: warning: symbol 'enable_loopback' was not declared. Should it be static?
drivers/char/synclinkmp.c:4101:6: warning: symbol 'set_rate' was not declared. Should it be static?
drivers/char/synclinkmp.c:4147:6: warning: symbol 'rx_stop' was not declared. Should it be static?
drivers/char/synclinkmp.c:4168:6: warning: symbol 'rx_start' was not declared. Should it be static?
drivers/char/synclinkmp.c:4225:6: warning: symbol 'tx_start' was not declared. Should it be static?
drivers/char/synclinkmp.c:4295:6: warning: symbol 'tx_stop' was not declared. Should it be static?
drivers/char/synclinkmp.c:4322:6: warning: symbol 'tx_load_fifo' was not declared. Should it be static?
drivers/char/synclinkmp.c:4371:6: warning: symbol 'reset_port' was not declared. Should it be static?
drivers/char/synclinkmp.c:4395:6: warning: symbol 'reset_adapter' was not declared. Should it be static?
drivers/char/synclinkmp.c:4407:6: warning: symbol 'async_mode' was not declared. Should it be static?
drivers/char/synclinkmp.c:4546:6: warning: symbol 'hdlc_mode' was not declared. Should it be static?
drivers/char/synclinkmp.c:4748:6: warning: symbol 'tx_set_idle' was not declared. Should it be static?
drivers/char/synclinkmp.c:4768:6: warning: symbol 'get_signals' was not declared. Should it be static?
drivers/char/synclinkmp.c:4797:6: warning: symbol 'set_signals' was not declared. Should it be static?
drivers/char/synclinkmp.c:4826:6: warning: symbol 'rx_reset_buffers' was not declared. Should it be static?
drivers/char/synclinkmp.c:4837:6: warning: symbol 'rx_free_frame_buffers' was not declared. Should it be static?
drivers/char/synclinkmp.c:4865:5: warning: symbol 'rx_get_frame' was not declared. Should it be static?
drivers/char/synclinkmp.c:5040:6: warning: symbol 'tx_load_dma_buffer' was not declared. Should it be static?
drivers/char/synclinkmp.c:5080:5: warning: symbol 'register_test' was not declared. Should it be static?
drivers/char/synclinkmp.c:5119:5: warning: symbol 'irq_test' was not declared. Should it be static?
drivers/char/synclinkmp.c:5211:5: warning: symbol 'init_adapter' was not declared. Should it be static?
drivers/char/synclinkmp.c:5270:5: warning: symbol 'loopback_test' was not declared. Should it be static?
drivers/char/synclinkmp.c:5335:5: warning: symbol 'adapter_test' was not declared. Should it be static?
drivers/char/synclinkmp.c:5397:5: warning: symbol 'memory_test' was not declared. Should it be static?
drivers/char/synclinkmp.c:5449:6: warning: symbol 'load_pci_memory' was not declared. Should it be static?
drivers/char/synclinkmp.c:5468:6: warning: symbol 'trace_block' was not declared. Should it be static?
drivers/char/synclinkmp.c:5503:6: warning: symbol 'tx_timeout' was not declared. Should it be static?
drivers/char/synclinkmp.c:5530:6: warning: symbol 'status_timeout' was not declared. Should it be static?
drivers/char/synclinkmp.c:5581:15: warning: symbol 'read_reg' was not declared. Should it be static?
drivers/char/synclinkmp.c:5586:6: warning: symbol 'write_reg' was not declared. Should it be static?
drivers/char/synclinkmp.c:5592:5: warning: symbol 'read_reg16' was not declared. Should it be static?
drivers/char/synclinkmp.c:5598:6: warning: symbol 'write_reg16' was not declared. Should it be static?
drivers/char/synclinkmp.c:5604:15: warning: symbol 'read_status_reg' was not declared. Should it be static?
drivers/char/synclinkmp.c:5610:6: warning: symbol 'write_control_reg' was not declared. Should it be static?

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

synclink drivers bool conversion

Remove more TRUE/FALSE defines and uses
Remove == TRUE tests
Convert BOOLEAN to bool
Convert int to bool where appropriate

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

serial: silence section mismatch warnings in 8250_pci

Fix following warnings:
WARNING: drivers/serial/built-in.o(.data+0x5b8): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_ite887x_exit()
WARNING: drivers/serial/built-in.o(.data+0x5e0): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_plx9050_exit()
WARNING: drivers/serial/built-in.o(.data+0x608): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_plx9050_exit()
WARNING: drivers/serial/built-in.o(.data+0x658): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_plx9050_exit()
WARNING: drivers/serial/built-in.o(.data+0x680): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_plx9050_exit()
WARNING: drivers/serial/built-in.o(.data+0x6a8): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_plx9050_exit()
WARNING: drivers/serial/built-in.o(.data+0x6d0): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:sbs_exit()
WARNING: drivers/serial/built-in.o(.data+0x6f8): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:sbs_exit()
WARNING: drivers/serial/built-in.o(.data+0x720): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:sbs_exit()
WARNING: drivers/serial/built-in.o(.data+0x748): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:sbs_exit()

pci_serial_quirks contains a number of function pointers where the referenced
function is annotated __devexit.  This is OK so we annotate pci_serial_quirks
with __refdata to ignore the __devexit references

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ncpfs: fix sparse warning in ncpsign_kernel.c

We're casting anyway, might as well cast to the correct sign.
Specific to i386 (ifdef __i386__)

fs/ncpfs/ncpsign_kernel.c:58:23: warning: incorrect type in initializer (different signedness)
fs/ncpfs/ncpsign_kernel.c:58:23:    expected unsigned int *data2
fs/ncpfs/ncpsign_kernel.c:58:23:    got int *<noident>

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Petr Vandrovec <VANDROVE@vc.cvut.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ncpfs: fix sparse warnings in ioctl.c

In both cases, these inode variables arebeing used to test the
server's root inode against NULL.  Change them to s_inode.
fs/ncpfs/ioctl.c:391:18: warning: symbol 'inode' shadows an earlier one
fs/ncpfs/ioctl.c:264:28: originally declared here
fs/ncpfs/ioctl.c:441:17: warning: symbol 'inode' shadows an earlier one
fs/ncpfs/ioctl.c:264:28: originally declared here

In this case, we are about to return anyway, just reuse result.
fs/ncpfs/ioctl.c:521:8: warning: symbol 'result' shadows an earlier one
fs/ncpfs/ioctl.c:268:6: originally declared here

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Petr Vandrovec <VANDROVE@vc.cvut.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ncpfs: add prototypes to ncp_fs.h

Removes some externs from C files, noticed from the sparse warnings:
fs/ncpfs/dir.c:90:26: warning: symbol 'ncp_root_dentry_operations' was not declared. Should it be static?
fs/ncpfs/symlink.c:107:5: warning: symbol 'ncp_symlink' was not declared. Should it be static?
fs/ncpfs/symlink.c:101:39: warning: symbol 'ncp_symlink_aops' was not declared. Should it be static?

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Petr Vandrovec <VANDROVE@vc.cvut.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

uml: clean up arch/um/drivers/ubd_kern.c

Make some global functions and variables static.

And remove some useless declarations for local functions, since we just need
to move their definitions ahead.

[jdike@addtoit.com: checkpatch cleanups]
Signed-off-by: WANG Cong <wangcong@zeuux.org>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

arch/um/os-Linux/sys-i386/task_size.c: improve a bit

Improve this code a bit: check sigaction's return value and remove a useless
fflush().

Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: WANG Cong <wangcong@zeuux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

uml: make several things static

Make several things static, because they no longer need to be global.

Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: WANG Cong <wangcong@zeuux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

uml: make three functions static

Make the following three functions static, since they don't need to be global.

arch/um/drivers/mcast_kern.c::mcast_setup()
arch/um/drivers/mconsole_user.c::mconsole_reply_v0()
arch/um/drivers/port_user.c::port_pre_exec()

Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: WANG Cong <wangcong@zeuux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

uml: remove a useless function

arch/um/drivers/chan_kern.c::chan_out_fd() is not used by anyone.  Remove it.

Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: WANG Cong <wangcong@zeuux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

uml: make a function static

arch/um/drivers/chan_kern.c::open_chan() can become static.

Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: WANG Cong <wangcong@zeuux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

arch/um/os-Linux/start_up.c: various improvements.

 - lets ptrace_child become void
 - adds checking for the return value of change_sig
 - moves errors info into stderr instead of stdout.

Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: WANG Cong <wangcong@zeuux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

uml: replace remaining __FUNCTION__ occurrences

__FUNCTION__ is gcc-specific, use __func__

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

arch/um/kernel/um_arch.c: some small improvements

Make some small improvements for arch/um/kernel/um_arch.c.

Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

cris: add constfy to pgd_offset()

add constfy to pgd_offset() for avoid following warnings.

  CC      mm/pagewalk.o
mm/pagewalk.c: In function 'walk_page_range':
mm/pagewalk.c:111: warning: passing argument 1 of 'pgd_offset' discards qualifiers from p\
ointer target type

Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: "Vegard Nossum" <vegard.nossum@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

cris: remove redundant display of free swap space in show_mem()

show_mem() has no need to print the amount of free swap space manually because
show_free_areas() does this already and is called by the former.

The two outputs only differ in text formatting:

  printk("Free swap  = %lukB\n", ...);
  printk("Free swap:       %6ldkB\n", ...);

Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

crisv10: prepare for BKL push down

Just the modem bits this time

Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

m68k: replace remaining __FUNCTION__ occurrences

__FUNCTION__ is gcc-specific, use __func__

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

m68k: remove redundant display of free swap space in show_mem()

show_mem() has no need to print the amount of free swap space manually because
show_free_areas() does this already and is called by the former.

The two outputs only differ in text formatting:

  printk("Free swap  = %lukB\n", ...);
  printk("Free swap:       %6ldkB\n", ...);

Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

alpha: teach the compiler that BUG doesn't return

Fix things like this:

security/selinux/netnode.c: In function 'sel_netnode_find':
security/selinux/netnode.c:126: warning: 'idx' may be used uninitialized in this function
security/selinux/netnode.c: In function 'sel_netnode_sid':
security/selinux/netnode.c:225: warning: 'ret' may be used uninitialized in this function
security/selinux/netnode.c:168: warning: 'idx' may be used uninitialized in this function

due to code correctly not expecting BUG() to return.

For some reason this reduces the object code size for that particular file.

Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

arch/alpha/kernel/traps.c: use time_* macros

The functions time_before, time_before_eq, time_after, and time_after_eq are
more robust for comparing jiffies against other values.

So implement usage of the time_after() macro, defined in linux/jiffies.h,
which deals with wrapping correctly

[akpm@linux-foundation.org: fix warning]
Signed-off-by: S.Caglar Onur <caglar@pardus.org.tr>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

alpha: replace __inline with inline

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

alpha: remove remaining __FUNCTION__ occurrences

__FUNCTION__ is gcc-specific, use __func__

The change in pci-iommu,c should be safe as arena has not been assigned
when we get to this point.

Some were within #if 0 blocks, have changed them and left the blocks
as they appear to be debugging infrastructure.

A #define FN __FUNCTION__ was removed and occurances of FN were replaced
with __func__ as well.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

alpha: handle kcalloc failure

arch/alpha/kernel/module.c (module_frob_arch_sections): Handle kcalloc failure.

Signed-off-by: Jim Meyering <meyering@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

smack: use cap_task_prctl

With the introduction of per-process securebits, the capabilities-related
prctl callbacks were moved into cap_task_prctl().  Have smack use
cap_task_prctl() so that PR_SET_KEEPCAPS is defined.

Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

smack: make smk_cipso_doi() and smk_unlbl_ambient()

The functions smk_cipso_doi and smk_unlbl_ambient are not used outside
smackfs.c and should hence be static.

Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

root_plug: use cap_task_prctl

With the introduction of per-process securebits, the capabilities-related
prctl callbacks were moved into cap_task_prctl().  Have root_plug use
cap_task_prctl() so that PR_SET_KEEPCAPS is defined.

Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

smack: fix integer as NULL pointer warning in smack_lsm.c

security/smack/smack_lsm.c:1257:16: warning: Using plain integer as NULL pointer

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

capabilities: implement per-process securebits

Filesystem capability support makes it possible to do away with (set)uid-0
based privilege and use capabilities instead.  That is, with filesystem
support for capabilities but without this present patch, it is (conceptually)
possible to manage a system with capabilities alone and never need to obtain
privilege via (set)uid-0.

Of course, conceptually isn't quite the same as currently possible since few
user applications, certainly not enough to run a viable system, are currently
prepared to leverage capabilities to exercise privilege.  Further, many
applications exist that may never get upgraded in this way, and the kernel
will continue to want to support their setuid-0 base privilege needs.

Where pure-capability applications evolve and replace setuid-0 binaries, it is
desirable that there be a mechanisms by which they can contain their
privilege.  In addition to leveraging the per-process bounding and inheritable
sets, this should include suppressing the privilege of the uid-0 superuser
from the process' tree of children.

The feature added by this patch can be leveraged to suppress the privilege
associated with (set)uid-0.  This suppression requires CAP_SETPCAP to
initiate, and only immediately affects the 'current' process (it is inherited
through fork()/exec()).  This reimplementation differs significantly from the
historical support for securebits which was system-wide, unwieldy and which
has ultimately withered to a dead relic in the source of the modern kernel.

With this patch applied a process, that is capable(CAP_SETPCAP), can now drop
all legacy privilege (through uid=0) for itself and all subsequently
fork()'d/exec()'d children with:

  prctl(PR_SET_SECUREBITS, 0x2f);

This patch represents a no-op unless CONFIG_SECURITY_FILE_CAPABILITIES is
enabled at configure time.

[akpm@linux-foundation.org: fix uninitialised var warning]
[serue@us.ibm.com: capabilities: use cap_task_prctl when !CONFIG_SECURITY]
Signed-off-by: Andrew G. Morgan <morgan@kernel.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Reviewed-by: James Morris <jmorris@namei.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Paul Moore <paul.moore@hp.com>
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/nommu.c: return 0 from kobjsize with invalid objects

Don't perform kobjsize operations on objects the kernel doesn't manage.

On Blackfin, drivers can get dma coherent memory by calling a function
dma_alloc_coherent(). We do this in nommu by configuring a chunk of uncached
memory at the top of memory.

Since we don't want the kernel to use the uncached memory, we lie to the
kernel, and tell it that it's max memory is between 0, and the start of the
uncached dma coherent section.

this all works well, until this memory gets exposed into userspace (with a
frame buffer), when you look at the process's maps, it shows the framebuf:

root:/proc> cat maps
[snip]
03f0ef00-03f34700 rw-p 00000000 1f:00 192        /dev/fb0
root:/proc>

This is outside the "normal" range for the kernel. When the kernel tries to
find the size of this object (when you run ps), it dies in nommu.c in
kobjsize.

BUG_ON(page->index >= MAX_ORDER);

since the page we are referring to is outside what the kernel thinks is it's
max valid memory.

root:~> while [ 1 ]; ps > /dev/null; done
kernel BUG at mm/nommu.c:119!
Kernel panic - not syncing: BUG!

We fixed this by adding a check to reject out of range object pointers as it
already does that for NULL pointers.

Signed-off-by: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

vmstats: add cond_resched() to refresh_cpu_vm_stats()

We've found that it can take quite a bit of time (100's of usec) to get
through the zone loop in refresh_cpu_vm_stats().

Adding a cond_resched() to allow other threads to run in the non-preemptive
case.

Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: fix broken gfp_zone with __GFP_THISNODE

This hack, "base = MAX_NR_ZONES", at __GFP_THISNODE was used for old
zonliests.

Now, new zonelist[] have a list for __GFP_THISNODE and this hack is incorrect.
Should be removed.

Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/page_alloc.c: remove hand-coded get_order()

Remove hand-coded get_order() from page_alloc.c.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

oom_kill: remove unused parameter in badness()

In commit 4c4a22148909e4c003562ea7ffe0a06e26919e3c, we moved the
memcontroller-related code from badness() to select_bad_process(), so the
parameter 'mem' in badness() is unused now.

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memory hotplug: free memmaps allocated by bootmem

This patch is to free memmaps which is allocated by bootmem.

Freeing usemap is not necessary.  The pages of usemap may be necessary for
other sections.

If removing section is last section on the node, its section is the final user
of usemap page.  (usemaps are allocated on its section by previous patch.) But
it shouldn't be freed too, because the section must be logical offline state
which all pages are isolated against page allocater.  If it is freed, page
alloctor may use it which will be removed physically soon.  It will be
disaster.  So, this patch keeps it as it is.

Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memory hotplug: allocate usemap on the section with pgdat

Usemaps are allocated on the section which has pgdat by this.

Because usemap size is very small, many other sections usemaps are allocated
on only one page.  If a section has usemap, it can't be removed until removing
other sections.  This dependency is not desirable for memory removing.

Pgdat has similar feature.  When a section has pgdat area, it must be the last
section for removing on the node.  So, if section A has pgdat and section B
has usemap for section A, Both sections can't be removed due to dependency
each other.

To solve this issue, this patch collects usemap on same section with pgdat.
If other sections doesn't have any dependency, this section will be able to be
removed finally.

Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memory hotplug: make alloc_bootmem_section()

alloc_bootmem_section() can allocate specified section's area.  This is used
for usemap to keep same section with pgdat by later patch.

Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memory hotplug: align memmap to page size

To free memmap easier, this patch aligns it to page size.  Bootmem allocater
may mix some objects in one pages.  It's not good for freeing memmap of memory
hot-remove.

Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memory hotplug: register section/node id to free

This patch set is to free pages which is allocated by bootmem for
memory-hotremove.  Some structures of memory management are allocated by
bootmem.  ex) memmap, etc.

To remove memory physically, some of them must be freed according to
circumstance.  This patch set makes basis to free those pages, and free
memmaps.

Basic my idea is using remain members of struct page to remember information
of users of bootmem (section number or node id).  When the section is
removing, kernel can confirm it.  By this information, some issues can be
solved.

  1) When the memmap of removing section is allocated on other
     section by bootmem, it should/can be free.
  2) When the memmap of removing section is allocated on the
     same section, it shouldn't be freed. Because the section has to be
     logical memory offlined already and all pages must be isolated against
     page allocater. If it is freed, page allocator may use it which will
     be removed physically soon.
  3) When removing section has other section's memmap,
     kernel will be able to show easily which section should be removed
     before it for user. (Not implemented yet)
  4) When the above case 2), the page isolation will be able to check and skip
     memmap's page when logical memory offline (offline_pages()).
     Current page isolation code fails in this case because this page is
     just reserved page and it can't distinguish this pages can be
     removed or not. But, it will be able to do by this patch.
     (Not implemented yet.)
  5) The node information like pgdat has similar issues. But, this
     will be able to be solved too by this.
     (Not implemented yet, but, remembering node id in the pages.)

Fortunately, current bootmem allocator just keeps PageReserved flags,
and doesn't use any other members of page struct. The users of
bootmem doesn't use them too.

This patch:

This is to register information which is node or section's id.  Kernel can
distinguish which node/section uses the pages allcated by bootmem.  This is
basis for hot-remove sections or nodes.

Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hugetlbfs: common code update for s390

Huge ptes have a special type on s390 and cannot be handled with the standard
pte functions in certain cases, e.g.  because of a different location of the
invalid bit.  This patch adds some new architecture- specific functions to
hugetlb common code, as a prerequisite for the s390 large page support.

This won't affect other architectures in functionality, but I need to add some
new dummy inline functions to the headers.

Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hugetlbfs: add missing TLB flush to hugetlb_cow()

A cow break on a hugetlbfs page with page_count > 1 will set a new pte with
set_huge_pte_at(), w/o any tlb flush operation.  The old pte will remain in
the tlb and subsequent write access to the page will result in a page fault
loop, for as long as it may take until the tlb is flushed from somewhere else.
 This patch introduces an architecture-specific huge_ptep_clear_flush()
function, which is called before the the set_huge_pte_at() in hugetlb_cow().

ATTENTION: This is just a nop on all architectures for now, the s390
implementation will come with our large page patch later.  Other architectures
should define their own huge_ptep_clear_flush() if needed.

Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>