arm64: dts: lg: Fix SPI controller node names

[ Upstream commit 09bae3b64cb580c95329bd8d16f08f0a5cb81ec9 ]

SPI controller nodes should be named 'spi' rather than 'ssp'. Fixing the
name enables dtc SPI bus checks.

Cc: Chanho Min <chanho.min@lge.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: amd: Fix SPI bus warnings

[ Upstream commit e9f0878c4b2004ac19581274c1ae4c61ae3ca70e ]

dtc has new checks for SPI buses. Fix the warnings in node names.

arch/arm64/boot/dts/amd/amd-overdrive.dtb: Warning (spi_bus_bridge): /smb/ssp@e1030000: node name for SPI buses should be 'spi'
arch/arm64/boot/dts/amd/amd-overdrive-rev-b0.dtb: Warning (spi_bus_bridge): /smb/ssp@e1030000: node name for SPI buses should be 'spi'
arch/arm64/boot/dts/amd/amd-overdrive-rev-b1.dtb: Warning (spi_bus_bridge): /smb/ssp@e1030000: node name for SPI buses should be 'spi'

Cc: Brijesh Singh <brijeshkumar.singh@amd.com>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: NCR5380: Handle BUS FREE during reselection

[ Upstream commit ca694afad707cb3ae2fdef3b28454444d9ac726e ]

The X3T9.2 specification (draft) says, under "6.1.4.2 RESELECTION time-out
procedure", that a target may assert RST or go to BUS FREE phase if the
initiator does not respond within 200 us. Something like this has been
observed with AztecMonster II target. When it happens, all we can do is wait
for the target to try again.

Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: NCR5380: Don't call dsprintk() following reselection interrupt

[ Upstream commit 08267216b3f8aa5adc204bdccf8deb72c1cd7665 ]

The X3T9.2 specification (draft) says, under "6.1.4.1 RESELECTION",

    ... The reselected initiator shall then assert the BSY signal
    within a selection abort time of its most recent detection of being
    reselected; this is required for correct operation of the time-out
    procedure.

The selection abort time is only 200 us which may be insufficient time for a
printk() call. Move the diagnostics to the error paths.

Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: NCR5380: Don't clear busy flag when abort fails

[ Upstream commit 45ddc1b24806cc8f1a09f23dd4e7b6e4a8ae36e1 ]

When NCR5380_abort() returns FAILED, the driver forgets that the target is
still busy. Hence, further commands may be sent to the target, which may fail
during selection and produce the error message, "reselection after won
arbitration?". Prevent this by leaving the busy flag set when NCR5380_abort()
fails.

Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: NCR5380: Check for invalid reselection target

[ Upstream commit 7ef55f6744c45e3d7c85a3f74ada39b67ac741dd ]

The X3T9.2 specification (draft) says, under "6.1.4.1 RESELECTION", that "the
initiator shall not respond to a RESELECTION phase if other than two SCSI ID
bits are on the DATA BUS." This issue (too many bits set) has been observed in
the wild, so add a check.

Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: NCR5380: Use DRIVER_SENSE to indicate valid sense data

[ Upstream commit 070356513963be6196142acff56acc8359069fa1 ]

When sense data is valid, call set_driver_byte(cmd, DRIVER_SENSE).  Otherwise
some callers of scsi_execute() will ignore sense data.  Don't set DID_ERROR or
DID_RESET just because sense data is missing.

Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: NCR5380: Clear all unissued commands on host reset

[ Upstream commit 1aeeeed7f03c576f096eede7b0384f99a98f588c ]

When doing a host reset we should be clearing all outstanding commands, not
just the command triggering the reset.

[mkp: adjusted Hannes' SoB address]

Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Ondrey Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

crypto: fix a memory leak in rsa-kcs1pad's encryption mode

[ Upstream commit 3944f139d5592790b70bc64f197162e643a8512b ]

The encryption mode of pkcs1pad never uses out_sg and out_buf, so
there's no need to allocate the buffer, which presently is not even
being freed.

CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: linux-crypto@vger.kernel.org
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Dan Aloni <dan@kernelim.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

crypto: s5p-sss: Fix Fix argument list alignment

[ Upstream commit 6c12b6ba45490eeb820fdceccf5a53f42a26799c ]

Fix misalignment of continued argument list.

Signed-off-by: Christoph Manszewski <c.manszewski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: L2CAP: Detect if remote is not able to use the whole MPS

[ Upstream commit a5c3021bb62b970713550db3f7fd08aa70665d7e ]

If the remote is not able to fully utilize the MPS choosen recalculate
the credits based on the actual amount it is sending that way it can
still send packets of MTU size without credits dropping to 0.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: realview: Fix SPI controller node names

[ Upstream commit 016add12977bcc30f77d7e48fc9a3a024cb46645 ]

SPI controller nodes should be named 'spi' rather than 'ssp'. Fixing the
name enables dtc SPI bus checks.

Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

EDAC: Raise the maximum number of memory controllers

[ Upstream commit 6b58859419554fb824e09cfdd73151a195473cbc ]

We observe an oops in the skx_edac module during boot:

  EDAC MC0: Giving out device to module skx_edac controller Skylake Socket#0 IMC#0
  EDAC MC1: Giving out device to module skx_edac controller Skylake Socket#0 IMC#1
  EDAC MC2: Giving out device to module skx_edac controller Skylake Socket#1 IMC#0
  ...
  EDAC MC13: Giving out device to module skx_edac controller Skylake Socket#0 IMC#1
  EDAC MC14: Giving out device to module skx_edac controller Skylake Socket#1 IMC#0
  EDAC MC15: Giving out device to module skx_edac controller Skylake Socket#1 IMC#1
  Too many memory controllers: 16
  EDAC MC: Removed device 0 for skx_edac Skylake Socket#0 IMC#0

We observe there are two memory controllers per socket, with a limit
of 16. Raise the maximum number of memory controllers from 16 to 2 *
MAX_NUMNODES (1024).

[ bp: This is just a band-aid fix until we've sorted out the whole issue
  with the bus_type association and handling in EDAC and can get rid of
  this arbitrary limit. ]

Signed-off-by: Justin Ernst <justin.ernst@hpe.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Russ Anderson <russ.anderson@hpe.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac@vger.kernel.org
Link: https://lkml.kernel.org/r/20180925143449.284634-1-justin.ernst@hpe.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: smsc: fix return type of ndo_start_xmit function

[ Upstream commit 6323d57f335ce1490d025cacc83fc10b07792130 ]

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: paz00: fix wakeup gpio keycode

[ Upstream commit ebea2a43fdafdbce918bd7e200b709d6c33b9f3b ]

The power key is controlled solely by the EC, which only tiggeres this
gpio after wakeup.
Fixes immediately return to suspend after wake from LP1.

Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: tegra: apalis_t30: fix mmc1 cmd pull-up

[ Upstream commit 1c997fe4becdc6fcbc06e23982ceb65621e6572a ]

Fix MMC1 cmd pin pull-up causing issues on carrier boards without
external pull-up.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: tegra30: fix xcvr-setup-use-fuses

[ Upstream commit 564706f65cda3de52b09e51feb423a43940fe661 ]

There was a dot instead of a comma. Fix this.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: libsas: always unregister the old device if going to discover new

[ Upstream commit 32c850bf587f993b2620b91e5af8a64a7813f504 ]

If we went into sas_rediscover_dev() the attached_sas_addr was already insured
not to be zero. So it's unnecessary to check if the attached_sas_addr is zero.

And although if the sas address is not changed, we always have to unregister
the old device when we are going to register a new one. We cannot just leave
the device there and bring up the new.

Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: chenxiang <chenxiang66@hisilicon.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

vfio/pci: Mask buggy SR-IOV VF INTx support

[ Upstream commit db04264fe9bc0f2b62e036629f9afb530324b693 ]

The SR-IOV spec requires that VFs must report zero for the INTx pin
register as VFs are precluded from INTx support.  It's much easier for
the host kernel to understand whether a device is a VF and therefore
whether a non-zero pin register value is bogus than it is to do the
same in userspace.  Override the INTx count for such devices and
virtualize the pin register to provide a consistent view of the device
to the user.

As this is clearly a spec violation, warn about it to support hardware
validation, but also provide a known whitelist as it doesn't do much
good to continue complaining if the hardware vendor doesn't plan to
fix it.

Known devices with this issue: 8086:270c

Tested-by: Gage Eads <gage.eads@intel.com>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

vfio/pci: Fix potential memory leak in vfio_msi_cap_len

[ Upstream commit 30ea32ab1951c80c6113f300fce2c70cd12659e4 ]

Free allocated vdev->msi_perm in error path.

Signed-off-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

misc: genwqe: should return proper error value.

[ Upstream commit 02241995b004faa7d9ff628e97f24056190853f8 ]

The function should return -EFAULT when copy_from_user fails. Even
though the caller does not distinguish them. but we should keep backward
compatibility.

Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

misc: kgdbts: Fix restrict error

[ Upstream commit fa0218ef733e6f247a1a3986e3eb12460064ac77 ]

kgdbts current fails when compiled with restrict:

drivers/misc/kgdbts.c: In function ‘configure_kgdbts’:
drivers/misc/kgdbts.c:1070:2: error: ‘strcpy’ source argument is the same as destination [-Werror=restrict]
  strcpy(config, opt);
  ^~~~~~~~~~~~~~~~~~~

As the error says, config is being used in both the source and destination.
Refactor the code to avoid the extra copy and put the parsing closer to
the actual location.

Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

coresight: tmc: Fix byte-address alignment for RRP

[ Upstream commit e7753f3937610633a540f2be81be87531f96ff04 ]

>From the comment in the code, it claims the requirement for byte-address
alignment for RRP register: 'for 32-bit, 64-bit and 128-bit wide trace
memory, the four LSBs must be 0s. For 256-bit wide trace memory, the
five LSBs must be 0s'.  This isn't consistent with the program, the
program sets five LSBs as zeros for 32/64/128-bit wide trace memory and
set six LSBs zeros for 256-bit wide trace memory.

After checking with the CoreSight Trace Memory Controller technical
reference manual (ARM DDI 0461B, section 3.3.4 RAM Read Pointer
Register), it proves the comment is right and the program does wrong
setting.

This patch fixes byte-address alignment for RRP by following correct
definition in the technical reference manual.

Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

coresight: etm4x: Configure EL2 exception level when kernel is running in HYP

[ Upstream commit b860801e3237ec4c74cf8de0be4816996757ae5c ]

For non-VHE systems host kernel runs at EL1 and jumps to EL2 whenever
hypervisor code should be executed. In this case ETM4x driver must
restrict configuration to EL1 when it setups kernel tracing.
However, there is no separate hypervisor privilege level when VHE
is enabled, the host kernel runs at EL2.

This patch fixes configuration of TRCACATRn register for VHE systems
so that ETM_EXLEVEL_NS_HYP bit is used instead of ETM_EXLEVEL_NS_OS
to on/off kernel tracing. At the same time, it moves common code
to new helper.

Signed-off-by: Tomasz Nowicki <tnowicki@caviumnetworks.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

coresight: Fix handling of sinks

[ Upstream commit c71369de02b285d9da526a526d8f2affc7b17c59 ]

The coresight components could be operated either in sysfs mode or in perf
mode. For some of the components, the mode of operation doesn't matter as
they simply relay the data to the next component in the trace path. But for
sinks, they need to be able to provide the trace data back to the user.
Thus we need to make sure that "mode" is handled appropriately. e.g,
the sysfs mode could have multiple sources driving the trace data, while
perf mode doesn't allow sharing the sink.

The coresight_enable_sink() however doesn't really allow this check to
trigger as it skips the "enable_sink" callback if the component is
already enabled, irrespective of the mode. This could cause mixing
of data from different modes or even same mode (in perf), if the
sources are different. Also, if we fail to enable the sink while
enabling a path (where sink is the first component enabled),
we could end up in disabling the components in the "entire"
path which were not enabled in this trial, causing disruptions
in the existing trace paths.

Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: gadget: uvc: Only halt video streaming endpoint in bulk mode

[ Upstream commit 8dbf9c7abefd5c1434a956d5c6b25e11183061a3 ]

When USB requests for video data fail to be submitted, the driver
signals a problem to the host by halting the video streaming endpoint.
This is only valid in bulk mode, as isochronous transfers have no
handshake phase and can't thus report a stall. The usb_ep_set_halt()
call returns an error when using isochronous endpoints, which we happily
ignore, but some UDCs complain in the kernel log. Fix this by only
trying to halt the endpoint in bulk mode.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Tested-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: gadget: uvc: Factor out video USB request queueing

[ Upstream commit 9d1ff5dcb3cd3390b1e56f1c24ae42c72257c4a3 ]

USB requests for video data are queued from two different locations in
the driver, with the same code block occurring twice. Factor it out to a
function.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Tested-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

phy: phy-twl4030-usb: fix denied runtime access

[ Upstream commit 6c7103aa026094a4ee2c2708ec6977a6dfc5331d ]

When runtime is not enabled, pm_runtime_get_sync() returns -EACCESS,
the counter will be incremented but the resume callback not called,
so enumeration and charging will not start properly.
To avoid that happen, disable irq on suspend and recheck on resume.

Practically this happens when the device is woken up from suspend by
plugging in usb.

Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: gadget: uvc: configfs: Prevent format changes after linking header

[ Upstream commit cb2200f7af8341aaf0c6abd7ba37e4c667c41639 ]

While checks are in place to avoid attributes and children of a format
being manipulated after the format is linked into the streaming header,
the linked flag was never actually set, invalidating the protections.
Update the flag as appropriate in the header link calls.

Signed-off-by: Joel Pepper <joel.pepper@rwth-aachen.de>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: gadget: uvc: configfs: Drop leaked references to config items

[ Upstream commit 86f3daed59bceb4fa7981d85e89f63ebbae1d561 ]

Some of the .allow_link() and .drop_link() operations implementations
call config_group_find_item() and then leak the reference to the
returned item. Fix this by dropping those references where needed.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: davinci: Fix implicit enum conversion warning

[ Upstream commit 4158757395b300b6eb308fc20b96d1d231484413 ]

Clang warns when one enumerated type is implicitly converted to another.

drivers/media/platform/davinci/vpbe_display.c:524:24: warning: implicit
conversion from enumeration type 'enum osd_v_exp_ratio' to different
enumeration type 'enum osd_h_exp_ratio' [-Wenum-conversion]
                        layer_info->h_exp = V_EXP_6_OVER_5;
                                          ~ ^~~~~~~~~~~~~~
1 warning generated.

This appears to be a copy and paste error judging from the couple of
lines directly above this statement and the way that height is handled
in the if block above this one.

Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: au0828: Fix incorrect error messages

[ Upstream commit f347596f2bf114a3af3d80201c6e6bef538d884f ]

Correcting red herring error messages.

Where appropriate, replaces au0282_dev_register with:
- au0828_analog_register
- au0828_dvb_register

Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: pci: ivtv: Fix a sleep-in-atomic-context bug in ivtv_yuv_init()

[ Upstream commit 8d11eb847de7d89c2754988c944d51a4f63e219b ]

The driver may sleep in a interrupt handler.

The function call paths (from bottom to top) in Linux-4.16 are:

[FUNC] kzalloc(GFP_KERNEL)
drivers/media/pci/ivtv/ivtv-yuv.c, 938:
kzalloc in ivtv_yuv_init
drivers/media/pci/ivtv/ivtv-yuv.c, 960:
ivtv_yuv_init in ivtv_yuv_next_free
drivers/media/pci/ivtv/ivtv-yuv.c, 1126:
ivtv_yuv_next_free in ivtv_yuv_setup_stream_frame
drivers/media/pci/ivtv/ivtv-irq.c, 827:
ivtv_yuv_setup_stream_frame in ivtv_irq_dec_data_req
drivers/media/pci/ivtv/ivtv-irq.c, 1013:
ivtv_irq_dec_data_req in ivtv_irq_handler

To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC.

This bug is found by my static analysis tool DSAC.

Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

MIPS: kexec: Relax memory restriction

[ Upstream commit a6da4d6fdf8bd512c98d3ac7f1d16bc4bb282919 ]

We can rely on the system kernel and the dump capture kernel themselves in
memory usage.

Being restrictive with 512MB limit may cause kexec tool failure on some
platforms.

Tested-by: Rachel Mozes <rachel.mozes@intel.com>
Reported-by: Rachel Mozes <rachel.mozes@intel.com>
Signed-off-by: Dengcheng Zhu <dzhu@wavecomp.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20568/
Cc: pburton@wavecomp.com
Cc: ralf@linux-mips.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/CPU: Use correct macros for Cyrix calls

[ Upstream commit 03b099bdcdf7125d4a63dc9ddeefdd454e05123d ]

There are comments in processor-cyrix.h advising you to _not_ make calls
using the deprecated macros in this style:

  setCx86_old(CX86_CCR4, getCx86_old(CX86_CCR4) | 0x80);

This is because it expands the macro into a non-functioning calling
sequence. The calling order must be:

  outb(CX86_CCR2, 0x22);
  inb(0x23);

From the comments:

 * When using the old macros a line like
 *   setCx86(CX86_CCR2, getCx86(CX86_CCR2) | 0x88);
 * gets expanded to:
 *  do {
 *    outb((CX86_CCR2), 0x22);
 *    outb((({
 *        outb((CX86_CCR2), 0x22);
 *        inb(0x23);
 *    }) | 0x88), 0x23);
 *  } while (0);

The new macros fix this problem, so use them instead.

Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Andy Lutomirski <luto@amacapital.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jia Zhang <qianyue.zj@alibaba-inc.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180921212041.13096-2-tedheadster@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: micrel: fix return type of ndo_start_xmit function

[ Upstream commit 2b49117a5abee8478b0470cba46ac74f93b4a479 ]

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bnx2x: Ignore bandwidth attention in single function mode

[ Upstream commit 75a110a1783ef8324ffd763b24f4ac268253cbca ]

This is a workaround for FW bug -
MFW generates bandwidth attention in single function mode, which
is only expected to be generated in multi function mode.
This undesired attention in SF mode results in incorrect HW
configuration and resulting into Tx timeout.

Signed-off-by: Shahed Shaikh <Shahed.Shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: marvell: Fix SPI and I2C bus warnings

[ Upstream commit cf680cc5251487b9a39919c3cda31a108af19cf8 ]

dtc has new checks for I2C and SPI buses. Fix the warnings in node names
and unit-addresses.

arch/arm/boot/dts/dove-cubox.dtb: Warning (i2c_bus_reg): /i2c-mux/i2c@0/clock-generator: I2C bus unit address format error, expected "60"
arch/arm/boot/dts/dove-cubox-es.dtb: Warning (i2c_bus_reg): /i2c-mux/i2c@0/clock-generator: I2C bus unit address format error, expected "60"
arch/arm/boot/dts/dove-cubox.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-cubox-es.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-dove-db.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-sbc-a510.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-sbc-a510.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@14600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/orion5x-kuroboxpro.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/orion5x-linkstation-lschl.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/orion5x-linkstation-lsgl.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/orion5x-linkstation-lswtgl.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"

Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

cpufeature: avoid warning when compiling with clang

[ Upstream commit c785896b21dd8e156326ff660050b0074d3431df ]

The table id (second) argument to MODULE_DEVICE_TABLE is often
referenced otherwise. This is not the case for CPU features. This
leads to warnings when building the kernel with Clang:
  arch/arm/crypto/aes-ce-glue.c:450:1: warning: variable
    'cpu_feature_match_AES' is not needed and will not be emitted
    [-Wunneeded-internal-declaration]
  module_cpu_feature_match(AES, aes_init);
  ^

Avoid warnings by using __maybe_unused, similar to commit 1f318a8bafcf
("modules: mark __inittest/__exittest as __maybe_unused").

Fixes: 67bad2fdb754 ("cpu: add generic support for CPU feature based module autoloading")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

spi: pic32: Use proper enum in dmaengine_prep_slave_rg

[ Upstream commit 8cfde7847d5ed0bb77bace41519572963e43cd17 ]

Clang warns when one enumerated type is converted implicitly to another:

drivers/spi/spi-pic32.c:323:8: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
                                          DMA_FROM_DEVICE,
                                          ^~~~~~~~~~~~~~~
drivers/spi/spi-pic32.c:333:8: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
                                          DMA_TO_DEVICE,
                                          ^~~~~~~~~~~~~
2 warnings generated.

Use the proper enums from dma_transfer_direction (DMA_FROM_DEVICE =
DMA_DEV_TO_MEM = 2, DMA_TO_DEVICE = DMA_MEM_TO_DEV = 1) to satify Clang.

Link: https://github.com/ClangBuiltLinux/linux/issues/159
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: ste: Fix SPI controller node names

[ Upstream commit 2f967f9e9fa076affb711da1a8389b5d33814fc6 ]

SPI controller nodes should be named 'spi' rather than 'ssp'. Fixing the
name enables dtc SPI bus checks.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: ux500: Fix LCDA clock line muxing

[ Upstream commit ecde29569e3484e1d0a032bf4074449bce4d4a03 ]

The "lcdaclk_b_1" group is muxed with the function "lcd"
but needs a separate entry to be muxed in with "lcda"
rather than "lcd".

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: ux500: Correct SCU unit address

[ Upstream commit 2f217d24ecaec2012e628d21e244eef0608656a4 ]

The unit address of the Cortex-A9 SCU device node contains one zero too
many.  Remove it.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

f2fs: fix to recover inode's uid/gid during POR

[ Upstream commit dc4cd1257c86451cec3e8e352cc376348e4f4af4 ]

Step to reproduce this bug:
1. logon as root
2. mount -t f2fs /dev/sdd /mnt;
3. touch /mnt/file;
4. chown system /mnt/file; chgrp system /mnt/file;
5. xfs_io -f /mnt/file -c "fsync";
6. godown /mnt;
7. umount /mnt;
8. mount -t f2fs /dev/sdd /mnt;

After step 8) we will expect file's uid/gid are all system, but during
recovery, these two fields were not been recovered, fix it.

Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: am335x-evm: fix number of cpsw

[ Upstream commit dcbf6b18d81bcdc51390ca1b258c17e2e13b7d0c ]

am335x-evm has only one CPSW external port physically wired, but DT defines
2 ext. ports. As result, PHY connection failure reported for the second
ext. port.

Update DT to reflect am335x-evm board HW configuration, and, while here,
switch to use phy-handle instead of phy_id.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mlxsw: spectrum: Init shaper for TCs 8..15

[ Upstream commit a9f36656b519a9a21309793c306941a3cd0eeb8f ]

With introduction of MC-aware mode to mlxsw, it became necessary to
configure TCs above 7 as well. There is now code in mlxsw to disable ETS
for these higher classes, but disablement of max shaper was neglected.

By default, max shaper is currently disabled to begin with, so the
problem is just cosmetic. However, for symmetry, do like we do for ETS
configuration, and call mlxsw_sp_port_ets_maxrate_set() for both TC i
and i + 8.

Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: chipidea: Fix otg event handler

[ Upstream commit 59739131e0ca06db7560f9073fff2fb83f6bc2a5 ]

At OTG work running time, it's possible that several events need to be
addressed (e.g. ID and VBUS events). The current implementation handles
only one event at a time which leads to ignoring the other one. Fix it.

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: chipidea: imx: enable OTG overcurrent in case USB subsystem is already started

[ Upstream commit 1dedbdf2bbb1ede8d96f35f9845ecae179dc1988 ]

When initializing the USB subsystem before starting the kernel,
OTG overcurrent detection is disabled. In case the OTG polarity of
overcurrent is low active, the overcurrent detection is never enabled
again and events cannot be reported as expected. Because imx usb
overcurrent polarity is low active by default, only detection needs
to be enable in usbmisc init function.

Signed-off-by: Nicolas Adell <nicolas.adell@actia.fr>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: amd: fix return type of ndo_start_xmit function

[ Upstream commit fe72352e37ae8478f4c97975a9831f0c50f22e73 ]

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: broadcom: fix return type of ndo_start_xmit function

[ Upstream commit 0c13b8d1aee87c35a2fbc1d85a1f766227cf54b5 ]

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: xilinx: fix return type of ndo_start_xmit function

[ Upstream commit 81255af8d9d5565004792c295dde49344df450ca ]

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: toshiba: fix return type of ndo_start_xmit function

[ Upstream commit bacade822524e02f662d88f784d2ae821a5546fb ]

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

power: supply: twl4030_charger: disable eoc interrupt on linear charge

[ Upstream commit 079cdff3d0a09c5da10ae1be35def7a116776328 ]

This avoids getting woken up from suspend after power interruptions
when the bci wrongly thinks the battery is full just because
of input current going low because of low input power

Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

power: supply: twl4030_charger: fix charging current out-of-bounds

[ Upstream commit 8314c212f995bc0d06b54ad02ef0ab4089781540 ]

the charging current uses unsigned int variables, if we step back
if the current is still low, we would run into negative which
means setting the target to a huge value.
Better add checks here.

Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

libfdt: Ensure INT_MAX is defined in libfdt_env.h

[ Upstream commit 53dd9dce6979bc54d64a3a09a2fb20187a025be7 ]

The next update of libfdt has a new dependency on INT_MAX. Update the
instances of libfdt_env.h in the kernel to either include the necessary
header with the definition or define it locally.

Cc: Russell King <linux@armlinux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/i40iw: Fix incorrect iterator type

[ Upstream commit 802fa45cd320de319e86c93bca72abec028ba059 ]

Commit f27b4746f378 ("i40iw: add connection management code") uses an
incorrect rcu iterator, whilst holding the rtnl_lock. Since the
critical region invokes i40iw_manage_qhash(), which is a sleeping
function, the rcu locking and traversal cannot be used.

Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/pseries: Disable CPU hotplug across migrations

[ Upstream commit 85a88cabad57d26d826dd94ea34d3a785824d802 ]

When performing partition migrations all present CPUs must be online
as all present CPUs must make the H_JOIN call as part of the migration
process. Once all present CPUs make the H_JOIN call, one CPU is returned
to make the rtas call to perform the migration to the destination system.

During testing of migration and changing the SMT state we have found
instances where CPUs are offlined, as part of the SMT state change,
before they make the H_JOIN call. This results in a hung system where
every CPU is either in H_JOIN or offline.

To prevent this this patch disables CPU hotplug during the migration
process.

Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/64s/hash: Fix stab_rr off by one initialization

[ Upstream commit 09b4438db13fa83b6219aee5993711a2aa2a0c64 ]

This causes SLB alloation to start 1 beyond the start of the SLB.
There is no real problem because after it wraps it stats behaving
properly, it's just surprisig to see when looking at SLB traces.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/iommu: Avoid derefence before pointer check

[ Upstream commit 984ecdd68de0fa1f63ce205d6c19ef5a7bc67b40 ]

The tbl pointer is being derefenced by IOMMU_PAGE_SIZE prior the check
if it is not NULL.

Just moving the dereference code to after the check, where there will
be guarantee that 'tbl' will not be NULL.

Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

serial: mxs-auart: Fix potential infinite loop

[ Upstream commit 5963e8a3122471cadfe0eba41c4ceaeaa5c8bb4d ]

On the error path of mxs_auart_request_gpio_irq() is performed
backward iterating with index i of enum type. Underline enum type
may be unsigned char. In this case check (--i >= 0) will be always
true and error handling goes into infinite loop.

The patch changes the check so that it is valid for signed and unsigned
types.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI/ACPI: Correct error message for ASPM disabling

[ Upstream commit 1ad61b612b95980a4d970c52022aa01dfc0f6068 ]

If _OSC execution fails today for platforms without an _OSC entry, code is
printing a misleading message saying disabling ASPM as follows:

  acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM

We need to ensure that platform supports ASPM to begin with.

Reported-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/qeth: invoke softirqs after napi_schedule()

[ Upstream commit 4d19db777a2f32c9b76f6fd517ed8960576cb43e ]

Calling napi_schedule() from process context does not ensure that the
NET_RX softirq is run in a timely fashion. So trigger it manually.

This is no big issue with current code. A call to ndo_open() is usually
followed by a ndo_set_rx_mode() call, and for qeth this contains a
spin_unlock_bh(). Except for OSN, where qeth_l2_set_rx_mode() bails out
early.
Nevertheless it's best to not depend on this behaviour, and just fix
the issue at its source like all other drivers do. For instance see
commit 83a0c6e58901 ("i40e: Invoke softirqs after napi_reschedule").

Fixes: a1c3ed4c9ca0 ("qeth: NAPI support for l2 and l3 discipline")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ath9k: Fix a locking bug in ath9k_add_interface()

[ Upstream commit 461cf036057477805a8a391e5fd0f5264a5e56a8 ]

We tried to revert commit d9c52fd17cb4 ("ath9k: fix tx99 with monitor
mode interface") but accidentally missed part of the locking change.

The lock has to be held earlier so that we're holding it when we do
"sc->tx99_vif = vif;" and also there in the current code there is a
stray unlock before we have taken the lock.

Fixes: 6df0580be8bc ("ath9k: add back support for using active monitor interfaces for tx99")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: rockchip: Fix erroneous SPI bus dtc warnings on rk3036

[ Upstream commit 131c3eb428ccd5f0c784b9edb4f72ec296a045d2 ]

dtc has new checks for SPI buses. The rk3036 dts file has a node named
spi' which causes false positive warnings. As the node is a pinctrl child
node, change the node name to be 'spi-pins' to fix the warnings.

arch/arm/boot/dts/rk3036-evb.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #address-cells for SPI bus
arch/arm/boot/dts/rk3036-kylin.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #address-cells for SPI bus
arch/arm/boot/dts/rk3036-evb.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #size-cells for SPI bus
arch/arm/boot/dts/rk3036-kylin.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #size-cells for SPI bus

Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ip_gre: fix parsing gre header in ipgre_err

[ Upstream commit b0350d51f001e6edc13ee4f253b98b50b05dd401 ]

gre_parse_header stops parsing when csum_err is encountered, which means
tpi->key is undefined and ip_tunnel_lookup will return NULL improperly.

This patch introduce a NULL pointer as csum_err parameter. Even when
csum_err is encountered, it won't return error and continue parsing gre
header as expected.

Fixes: 9f57c67c379d ("gre: Remove support for sharing GRE protocol hook.")
Reported-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

kernfs: Fix range checks in kernfs_get_target_path

[ Upstream commit a75e78f21f9ad4b810868c89dbbabcc3931591ca ]

The terminating NUL byte is only there because the buffer is
allocated with kzalloc(PAGE_SIZE, GFP_KERNEL), but since the
range-check is off-by-one, and PAGE_SIZE==PATH_MAX, the
returned string may not be zero-terminated if it is exactly
PATH_MAX characters long.  Furthermore also the initial loop
may theoretically exceed PATH_MAX and cause a fault.

Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

component: fix loop condition to call unbind() if bind() fails

[ Upstream commit bdae566d5d9733b6e32b378668b84eadf28a94d4 ]

During component_bind_all(), if bind() fails for any
particular component associated with a master, unbind()
should be called for all previous components in that
master's match array, whose bind() might have completed
successfully. As per the current logic, if bind() fails
for the component at position 'n' in the master's match
array, it would start calling unbind() from component in
'n'th position itself and work backwards, and will always
skip calling unbind() for component in 0th position in the
master's match array.
Fix this by updating the loop condition, and the logic to
refer to the components in master's match array, so that
unbind() is called for all components starting from 'n-1'st
position in the array, until (and including) component in
0th position.

Signed-off-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

power: supply: max8998-charger: Fix platform data retrieval

[ Upstream commit cb90a2c6f77fe9b43d1e3f759bb2f13fe7fa1811 ]

Since the max8998 MFD driver supports instantiation by DT, platform data
retrieval is handled in MFD probe and cell drivers should get use
the pdata field of max8998_dev struct to obtain them.

Fixes: ee999fb3f17f ("mfd: max8998: Add support for Device Tree")
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

power: reset: at91-poweroff: do not procede if at91_shdwc is allocated

[ Upstream commit 9f1e44774be578fb92776add95f1fcaf8284d692 ]

There should be only one instance of struct shdwc in the system. This is
referenced through at91_shdwc. Return in probe if at91_shdwc is already
allocated.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

power: supply: ab8500_fg: silence uninitialized variable warnings

[ Upstream commit 54baff8d4e5dce2cef61953b1dc22079cda1ddb1 ]

If kstrtoul() fails then we print "charge_full" when it's uninitialized.
The debug printk doesn't add anything so I deleted it and cleaned these
two functions up a bit.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

cxgb4: Fix endianness issue in t4_fwcache()

[ Upstream commit 0dc235afc59a226d951352b0adf4a89b532a9d13 ]

Do not put host-endian 0 or 1 into big endian feild.

Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pinctrl: at91: don't use the same irqchip with multiple gpiochips

[ Upstream commit 0c3dfa176912b5f87732545598200fb55e9c1978 ]

Sharing the same irqchip with multiple gpiochips is not a good
practice. For instance, when installing hooks, we change the state
of the irqchip. The initial state of the irqchip for the second
gpiochip to register is then disrupted.

Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: socfpga: Fix I2C bus unit-address error

[ Upstream commit cbbc488ed85061a765cf370c3e41f383c1e0add6 ]

dtc has new checks for I2C buses. Fix the warnings in unit-addresses.

arch/arm/boot/dts/socfpga_cyclone5_de0_sockit.dtb: Warning (i2c_bus_reg): /soc/i2c@ffc04000/adxl345@0: I2C bus unit address format error, expected "53"

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/vdso: Correct call frame information

[ Upstream commit 56d20861c027498b5a1112b4f9f05b56d906fdda ]

Call Frame Information is used by gdb for back-traces and inserting
breakpoints on function return for the "finish" command.  This failed
when inside __kernel_clock_gettime.  More concerning than difficulty
debugging is that CFI is also used by stack frame unwinding code to
implement exceptions.  If you have an app that needs to handle
asynchronous exceptions for some reason, and you are unlucky enough to
get one inside the VDSO time functions, your app will crash.

What's wrong:  There is control flow in __kernel_clock_gettime that
reaches label 99 without saving lr in r12.  CFI info however is
interpreted by the unwinder without reference to control flow: It's a
simple matter of "Execute all the CFI opcodes up to the current
address".  That means the unwinder thinks r12 contains the return
address at label 99.  Disabuse it of that notion by resetting CFI for
the return address at label 99.

Note that the ".cfi_restore lr" could have gone anywhere from the
"mtlr r12" a few instructions earlier to the instruction at label 99.
I put the CFI as late as possible, because in general that's best
practice (and if possible grouped with other CFI in order to reduce
the number of CFI opcodes executed when unwinding).  Using r12 as the
return address is perfectly fine after the "mtlr r12" since r12 on
that code path still contains the return address.

__get_datapage also has a CFI error.  That function temporarily saves
lr in r0, and reflects that fact with ".cfi_register lr,r0".  A later
use of r0 means the CFI at that point isn't correct, as r0 no longer
contains the return address.  Fix that too.

Signed-off-by: Alan Modra <amodra@gmail.com>
Tested-by: Reza Arbab <arbab@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: qcom: ipq4019: fix cpu0's qcom,saw2 reg value

[ Upstream commit bd73a3dd257fb838bd456a18eeee0ef0224b7a40 ]

while compiling an ipq4019 target, dtc will complain:
regulator@b089000 unit address format error, expected "2089000"

The saw0 regulator reg value seems to be
copied and pasted from qcom-ipq8064.dtsi.

This patch fixes the reg value to match that of the
unit address which in turn silences the warning.
(There is no driver for qcom,saw2 right now.
So this went unnoticed)

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

llc: avoid blocking in llc_sap_close()

[ Upstream commit 9708d2b5b7c648e8e0a40d11e8cea12f6277f33c ]

llc_sap_close() is called by llc_sap_put() which
could be called in BH context in llc_rcv(). We can't
block in BH.

There is no reason to block it here, kfree_rcu() should
be sufficient.

Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pinctrl: at91-pio4: fix has_config check in atmel_pctl_dt_subnode_to_map()

[ Upstream commit b97760ae8e3dc8bb91881c13425a0bff55f2bd85 ]

Smatch complains about this condition:

if (has_config && num_pins >= 1)

The "has_config" variable is either uninitialized or true.  The
"num_pins" variable is unsigned and we verified that it is non-zero on
the lines before so we know "num_pines >= 1" is true.  Really, we could
just check "num_configs" directly and remove the "has_config" variable.

Fixes: 776180848b57 ("pinctrl: introduce driver for Atmel PIO4 controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: intel8x0m: Register irq handler after register initializations

[ Upstream commit 7064f376d4a10686f51c879401a569bb4babf9c6 ]

The interrupt handler has to be acquired after the other resource
initialization when allocated with IRQF_SHARED.  Otherwise it's
triggered before the resource gets ready, and may lead to unpleasant
behavior.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: dvb: fix compat ioctl translation

[ Upstream commit 1ccbeeb888ac33627d91f1ccf0b84ef3bcadef24 ]

The VIDEO_GET_EVENT and VIDEO_STILLPICTURE was added back in 2005 but
it never worked because the command number is wrong.

Using the right command number means we have a better chance of them
actually doing the right thing, though clearly nobody has ever tried
it successfully.

I noticed these while auditing the remaining users of compat_time_t
for y2038 bugs. This one is fine in that regard, it just never did
anything.

Fixes: 6e87abd0b8cb ("[DVB]: Add compat ioctl handling.")

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: fix: media: pci: meye: validate offset to avoid arbitrary access

[ Upstream commit eac7230fdb4672c2cb56f6a01a1744f562c01f80 ]

Motion eye video4linux driver for Sony Vaio PictureBook desn't validate user-controlled parameter
'vma->vm_pgoff', a malicious process might access all of kernel memory from user space by trying
pass different arbitrary address.
Discussion: http://www.openwall.com/lists/oss-security/2018/07/06/1

Signed-off-by: Lao Wei <zrlw@qq.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvmem: core: return error code instead of NULL from nvmem_device_get

[ Upstream commit ca6ac25cecf0e740d7cc8e03e0ebbf8acbeca3df ]

nvmem_device_get() should return ERR_PTR() on error or valid pointer
on success, but one of the code path seems to return NULL, so fix it.

Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

kprobes: Don't call BUG_ON() if there is a kprobe in use on free list

[ Upstream commit cbdd96f5586151e48317d90a403941ec23f12660 ]

Instead of calling BUG_ON(), if we find a kprobe in use on free kprobe
list, just remove it from the list and keep it on kprobe hash list
as same as other in-use kprobes.

Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S . Miller <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Naveen N . Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/153666126882.21306.10738207224288507996.stgit@devbox
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: pm80xx: Fixed system hang issue during kexec boot

[ Upstream commit 72349b62a571effd6faadd0600b8e657dd87afbf ]

When the firmware is not responding, execution of kexec boot causes a system
hang. When firmware assertion happened, driver get notified with interrupt
vector updated in MPI configuration table. Then, the driver will read
scratchpad register and set controller_fatal_error flag to true.

Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: pm80xx: Corrected dma_unmap_sg() parameter

[ Upstream commit 76cb25b058034d37244be6aca97a2ad52a5fbcad ]

For the function dma_unmap_sg(), the <nents> parameter should be number of
elements in the scatter list prior to the mapping, not after the mapping.

Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: imx6: register pm_power_off handler if "fsl,pmic-stby-poweroff" is set

[ Upstream commit 8148d2136002da2e2887caf6a07bbd9c033f14f3 ]

One of the Freescale recommended sequences for power off with external
PMIC is the following:
...
3.  SoC is programming PMIC for power off when standby is asserted.
4.  In CCM STOP mode, Standby is asserted, PMIC gates SoC supplies.

See:
http://www.nxp.com/assets/documents/data/en/reference-manuals/IMX6DQRM.pdf
page 5083

This patch implements step 4. of this sequence.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: sym53c8xx: fix NULL pointer dereference panic in sym_int_sir()

[ Upstream commit 288315e95264b6355e26609e9dec5dc4563d4ab0 ]

sym_int_sir() in sym_hipd.c does not check the command pointer for NULL before
using it in debug message prints.

Suggested-by: Matthew Wilcox <matthew.wilcox@oracle.com>
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Acked-by: Matthew Wilcox <matthew.wilcox@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

f2fs: fix memory leak of percpu counter in fill_super()

[ Upstream commit 4a70e255449c9a13eed7a6eeecc85a1ea63cef76 ]

In fill_super -> init_percpu_info, we should destroy percpu counter
in error path, otherwise memory allcoated for percpu counter will
leak.

Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

signal: Properly deliver SIGSEGV from x86 uprobes

[ Upstream commit 4a63c1ffd384ebdce40aac9c997dab68379137be ]

For userspace to tell the difference between an random signal
and an exception, the exception must include siginfo information.

Using SEND_SIG_FORCED for SIGSEGV is thus wrong, and it will result in
userspace seeing si_code == SI_USER (like a random signal) instead of
si_code == SI_KERNEL or a more specific si_code as all exceptions
deliver.

Therefore replace force_sig_info(SIGSEGV, SEND_SIG_FORCE, current)
with force_sig(SIG_SEGV, current) which gets this right and is shorter
and easier to type.

Fixes: 791eca10107f ("uretprobes/x86: Hijack return address")
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

signal: Properly deliver SIGILL from uprobes

[ Upstream commit 55a3235fc71bf34303e34a95eeee235b2d2a35dd ]

For userspace to tell the difference between a random signal and an
exception, the exception must include siginfo information.

Using SEND_SIG_FORCED for SIGILL is thus wrong, and it will result
in userspace seeing si_code == SI_USER (like a random signal) instead
of si_code == SI_KERNEL or a more specific si_code as all exceptions
deliver.

Therefore replace force_sig_info(SIGILL, SEND_SIG_FORCE, current)
with force_sig(SIG_ILL, current) which gets this right and is
shorter and easier to type.

Fixes: 014940bad8e4 ("uprobes/x86: Send SIGILL if arch_uprobe_post_xol() fails")
Fixes: 0b5256c7f173 ("uprobes: Send SIGILL if handle_trampoline() fails")
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

signal: Always ignore SIGKILL and SIGSTOP sent to the global init

[ Upstream commit 86989c41b5ea08776c450cb759592532314a4ed6 ]

If the first process started (aka /sbin/init) receives a SIGKILL it
will panic the system if it is delivered.  Making the system unusable
and undebugable.  It isn't much better if the first process started
receives SIGSTOP.

So always ignore SIGSTOP and SIGKILL sent to init.

This is done in a separate clause in sig_task_ignored as force_sig_info
can clear SIG_UNKILLABLE and this protection should work even then.

Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ath9k: add back support for using active monitor interfaces for tx99

[ Upstream commit 6df0580be8bc30803c4d8b2ed9c2230a2740c795 ]

Various documented examples on how to set up tx99 with ath9k rely
on setting up a regular monitor interface for setting the channel.
My previous patch "ath9k: fix tx99 with monitor mode interface" made
it possible to set it up this way again. However, it was removing support
for using an active monitor interface, which is required for controlling
the bitrate as well, since the bitrate is not passed down with a regular
monitor interface.

This patch partially reverts the previous one, but keeps support for using
a regular monitor interface to keep documented steps working in cases
where the bitrate does not matter

Fixes: d9c52fd17cb48 ("ath9k: fix tx99 with monitor mode interface")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dmaengine: dma-jz4780: Further residue status fix

[ Upstream commit 83ef4fb7556b6a673f755da670cbacab7e2c7f1b ]

Func jz4780_dma_desc_residue() expects the index to the next hw
descriptor as its last parameter. Caller func jz4780_dma_tx_status(),
however, applied modulus before passing it. When the current hw
descriptor was last in the list, the index passed became zero.

The resulting excess of reported residue especially caused problems
with cyclic DMA transfer clients, i.e. ALSA AIC audio output, which
rely on this for determining current DMA location within buffer.

Combined with the recent and related residue-reporting fixes, spurious
ALSA audio underruns on jz4770 hardware are now fixed.

Signed-off-by: Daniel Silsby <dansilsby@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dmaengine: dma-jz4780: Don't depend on MACH_JZ4780

[ Upstream commit c558ecd21c852c97ff98dc6c61f715ba420ec251 ]

If we make this driver depend on MACH_JZ4780, that means it can be
enabled only if we're building a kernel specially crafted for a
JZ4780-based board, while most GNU/Linux distributions will want one
generic MIPS kernel that works on multiple boards.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: omap3-gta04: keep vpll2 always on

[ Upstream commit 1ae00833e30c9b4af5cbfda65d75b1de12f74013 ]

This is needed to make the display and venc work properly.
Compare to omap3-beagle.dts.

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: omap3-gta04: make NAND partitions compatible with recent U-Boot

[ Upstream commit fa99c21ecb3cd4021a60d0e8bf880e78b5bd0729 ]

Vendor defined U-Boot has changed the partition scheme a while ago:

* kernel partition 6MB
* file system partition uses the remainder up to end of the NAND
* increased size of the environment partition (to get an OneNAND compatible base address)
* shrink the U-Boot partition

Let's be compatible (e.g. Debian kernel built from upstream).

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: omap3-gta04: fix touchscreen tsc2007

[ Upstream commit 7384a24248eda140a234d356b6c840701ee9f055 ]

we fix penirq polarity, add penirq pinmux and touchscreen
properties.

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: omap3-gta04: tvout: enable as display1 alias

[ Upstream commit 8905592b6e50cec905e6c6035bbd36201a3bfac1 ]

The omap dss susbystem takes the display aliases to find
out which displays exist. To enable tv-out we must define
an alias.

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: omap3-gta04: fixes for tvout / venc

[ Upstream commit f6591391373dbff2c0200e1055d4ff86191578d2 ]

* fix connector compatibility (composite)
* add comment for gpio1 23
* add proper #address-cells
* we use only one venc_out channel for composite

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: omap3-gta04: give spi_lcd node a label so that we can overwrite in other DTS files

[ Upstream commit fa0d7dc355c890725b6178dab0cc11b194203afa ]

needed for device variants based on GTA04 board but with
different display panel (driver).

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

of: make PowerMac cache node search conditional on CONFIG_PPC_PMAC

[ Upstream commit f6707fd6241e483f6fea2caae82d876e422bb11a ]

Cache nodes under the cpu node(s) is PowerMac specific according to the
comment above, so make the code enforce that.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>